2016/05/20

2016/05/20
2016/05/20
 ITEM DESCRIPTION MATERIAL QTY
1 DUMMY LEG TO MATCH SUPPORTED LINE 1
2 UPPER BASE PLATE CSA G40.21 (260W MIN.) 1
3 MACHINE BOLT C/W 2 HEX NUTS CARBON STEEL 1
4 LOWER BASE PLATE CSA G40.21 (260W MIN) 1

LINE SIZE NPS DUMMY LEG NPS & SCH PLATE SIZE (OD x T) ID BOLT SIZE

2 1-1/2 SCH80 Ø 75x12 Ø 40 M33x250

3 2 SCH80 Ø 75x12 Ø 45 M39x250
4 2 SCH80 Ø 75x12 Ø 45 M39x250
6 3 STD Ø 100x12 Ø 50 M45x250
8 3 STD Ø 100x12 Ø 50 M45x250
10 4 STD Ø 150x16 Ø 50 M45x250
12 4 STD Ø 150x16 Ø 50 M45x250

TYP
6

Ø10 WEEP HOLE

THRU DUMMY LEG TYP
TYP 1 6

L
(1200 MAX) 2
(350 MIN) 25
TYP 3 MACHINE
BOLT HEAD

ØID
CLEARANCE ØOD
HOLE

LOWER BASE PLATE

UPPER BASE PLATE DETAIL
DETAIL

NOTES:
1. BASE SUPPORT TO REST ON STRUCTURAL STEEL OR CONCRETE
2. PLACE BASE SUPPORT AFTER GROUT IS CURED IF APPLICABLE
3. ALL DIMENSIONS IN mm
4. DIMENSION "L" TO BE DEFINED ON PIPING ISOMETRIC
5. DO NOT CUT HOLE IN HEADER 2017/03/14
TAG: BS-04
EXAMPLE: BS-04
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2015/12/01 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
ADJUSTABLE BASE SUPPORT
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2015/12/01 NTS A BS-04 0
 ITEM DESCRIPTION MATERIAL QTY
1 9.5 mm PLATE CSA G40.21 (260W MIN.) 1
2 6.0 mm PLATE CSA G40.21 (260W MIN.) 1
3 LISEGA 42..19 PIPE CLAMP CARBON STEEL 2
4 LINER EPDM RUBBER 2

LINE SIZE H OPTIONAL WT MAXIMUM DESIGN LOADS (kN) BOLT

CODE SECTION TORQUE
(NPS) (mm) (NOTE 2) VERTICAL AXIAL LATERAL (ft-lbs)
100 A WT100x11.3
2-4 7.5 3 3 30
150 B WT155x16.4
100 A WT100x11.3
6-8 10 3.4 3.4 80
150 B WT155x16.4

20
45°
6
TYP 2 H
6
1
20
A
25 L/2
100
L

SECTION A-A

NOTES:
1. LINER MATERIAL BASED ON SERVICE TEMPERATURE
2. STANDARD LENGTH IS 300 OR 450mm
3. ITEMS 1 & 2 CAN BE EXCHANGED FOR STRUCTURAL TEE SPECIFIED
4. ALL DIMENSIONS IN mm
5. BOLTS REQUIRE LUBRICATION FOR RATED BOLT TORQUE
6. INSPECT SHOE POSITION AND BOLT TORQUE AT REGULAR INTERVALS
BASED ON OPERATING CONDITIONS. RE-TORQUE AS REQUIRED. 2017/03/14
TAG: CS-01-CODE-LENGTH
EXAMPLE: CS-01-A-300
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2015/12/01 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
CLAMPED PIPE SHOE 2-8 NPS
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2015/12/01 NTS A CS-01 0
 ITEM DESCRIPTION MATERIAL QTY
1 12.7mm PLATE CSA G40.21 (260W MIN.) 1
2 9.5mm PLATE CSA G40.21 (260W MIN.) 1
3 9.5mm PLATE CSA G40.21 (260W MIN.) 2
4 LISEGA 42 .. 19 PIPE CLAMP CARBON STEEL 2
5 LINER EPDM RUBBER 2

MAXIMUM DESIGN LOADS (kN)

LINE SIZE W H OPTIONAL WT BOLT TORQUE
(NPS) (mm) (mm) CODE SECTION (NOTE 3) (ft-lbs)
VERTICAL AXIAL LATERAL
100 A WT100x18
10-16 150 40 25 15 130
150 B WT155x22.3
100 A WT100x23.1
18-24 200 60 40 20 200
150 B WT155x30

45°
5

6
TYP
6
3
8 H
2
8
12 8 L/2
1 TYP
W 8 L

NOTES:
1. LINER MATERIAL BASED ON SERVICE TEMPERATURE
2017/03/14
2. STANDARD LENGTH IS 300 OR 450mm
3. ITEMS 1 & 2 CAN BE EXCHANGED FOR STRUCTURAL TEE SPECIFIED
4. ALL DIMENSIONS IN mm
5. BOLTS REQUIRE LUBRICATION FOR RATED BOLT TORQUE
6. INSPECT SHOE POSITION AND BOLT TORQUE AT REGULAR INTERVALS BASED ON OPERATING
CONDITIONS. RE-TORQUE AS REQUIRED.

TAG: CS-02-CODE-LENGTH
EXAMPLE: CS-02-A-300
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2015/12/01 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
CLAMPED PIPE SHOE 10-24 NPS
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2015/12/01 NTS A CS-02 0
 ITEM DESCRIPTION MATERIAL QTY
1 9.5 mm PLATE CSA G40.21 (260W MIN.) 1
2 6.0 mm PLATE CSA G40.21 (260W MIN.) 1
3 6.0 mm PLATE CSA G40.21 (260W MIN.) 3
4 LISEGA 42 .. 19 PIPE CLAMP CARBON STEEL 3
5 LINER EPDM RUBBER 3

LINE SIZE C H OPTIONAL WT MAXIMUM DESIGN LOADS (kN) BOLT

HEIGHT SECTION TORQUE
(NPS) (mm) (mm) CODE (NOTE 2) VERTICAL AXIAL LATERAL (ft-lbs)
100 A WT100x11.3
1-1.5 25 5 7.5 2.5 25
150 B WT155x16.4
100 A WT100x11.3
2-4 13 10 15 5 30
150 B WT155x16.4

6
TYP
6
A
6
4 TYP
6
5

3
20
2 Cx45°
TYP
6 H
TYP 6 TYP
6
1 20
6 25 L/2
TYP A
100 6 450

SECTION A-A

NOTES:
1. LINER MATERIAL BASED ON SERVICE TEMPERATURE
2. STANDARD LENGTH IS 450, 600 OR 750mm
3. ITEMS 1 & 2 CAN BE EXCHANGED FOR STRUCTURAL TEE SPECIFIED
4. ALL DIMENSIONS IN mm
5. BOLTS REQUIRE LUBRICATION FOR RATED BOLT TORQUE
6. INSPECT SHOE POSITION AND BOLT TORQUE AT REGULAR INTERVALS 2017/03/20
BASED ON OPERATING CONDITIONS. RE-TORQUE AS REQUIRED.
TAG: CS-03-CODE-LENGTH
EXAMPLE: CS-03-A-450
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2017/03/16 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
XL CLAMPED PIPE SHOE 1-4 NPS
DESIGNED J.MEITZ
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2017/03/16 NTS A CS-03 0
 ITEM DESCRIPTION MATERIAL QTY
1 12.7mm PLATE CSA G40.21 (260W MIN.) 1
2 9.5mm PLATE CSA G40.21 (260W MIN.) 1
3 9.5mm PLATE CSA G40.21 (260W MIN.) 3
4 LISEGA 42 .. 19 PIPE CLAMP CARBON STEEL 3
5 LINER EPDM RUBBER 3

LINE SIZE W H OPTIONAL WT MAXIMUM DESIGN LOADS (kN) BOLT TORQUE

HEIGHT SECTION
(NPS) (mm) (mm) CODE (NOTE 3) VERTICAL AXIAL LATERAL (ft-lbs)

100 A WT100x11.3
6-8 100 20 25 15 80
150 B WT155x16.4
100 A WT100x18
10-16 150 40 40 20 130
150 B WT155x22.3
100 A WT100x23.1
18-24 200 60 60 25 200
150 B WT155x30

45° 5 8
TYP
8
6
TYP
6 20

3
H
8
TYP 2
8 8 20
1 TYP 25 L/2
12 8
A
W L

SECTION A-A

NOTES:
1. LINER MATERIAL IS BASED ON SERVICE TEMPERATURE
2. STANDARD LENGTH IS 600, 750 OR 900mm
3. ITEMS 1 & 2 CAN BE EXCHANGED FOR STRUCTURAL TEE SPECIFIED
4. ALL DIMENSIONS IN mm
5. BOLTS REQUIRE LUBRICANT FOR RATED BOLT TORQUE
6. INSPECT SHOE POSITION AND BOLT TORQUE AT REGULAR INTERVALS BASED ON
OPERATING CONDITIONS. RE-TORQUE AS REQUIRED. 2017/03/14
TAG: CS-03-CODE-LENGTH
EXAMPLE: CS-03-A-600
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2015/12/01 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
XL CLAMPED PIPE SHOE 6-24 NPS
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2015/12/01 NTS A CS-03 0
ITEM DESCRIPTION MATERIAL QTY
1 19.0mm PLATE CSA G40.21 (260W MIN.) 1
2 12.7mm PLATE CSA G40.21 (260W MIN.) 2
3 12.7mm PLATE CSA G40.21 (260W MIN.) 3
4 LISEGA 42 .. 19 PIPE CLAMP CARBON STEEL 3
5 LINER EPDM RUBBER 3

LINE SIZE W H HEIGHT MAXIMUM DESIGN LOADS (kN) BOLT TORQUE

(NPS) (mm) (mm) CODE VERTICAL AXIAL LATERAL (ft-lbs)
100 A
30 400 300
150 B
120 80 50
100 A
36 550 400
150 B

5
22.5°

4 20
2 TYP
TYP 8
8
3 H 20
12 TYP 25(TYP)
1
6
W L

NOTES:
1. LINER MATERIAL BASED ON SERVICE TEMPERATURE
2. STANDARD LENGTH IS 600, 750 OR 900mm
3. ALL DIMENSIONS IN mm
4. BOLTS REQUIRE LUBRICATION FOR RATED BOLT TORQUE
5. INSPECT SHOE POSITION AND BOLT TORQUE AT REGULAR INTERVALS BASED
ON OPERATING CONDITIONS. RE-TORQUE AS REQUIRED. 2017/03/14
TAG: CS-04
CS-04-CODE-LENGTH
EXAMPLE: CS-04-A-600
CS-04
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2015/12/01 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
CLAMPED SHOE 30-36 NPS
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2015/12/01 NTS A CS-04 0
2016/05/20
2016/05/20
2016/05/20
2016/05/20
2016/05/20
 ITEM DESCRIPTION MATERIAL QTY
1 DUMMY LEG TO MATCH SUPPORTED LINE 1
DUMMY LEG NPS & SCH CODE
LINE SIZE NPS
A B
2 1-1/2 SCH80 LINE SIZE x SCH80
3 - 4 2 SCH80 LINE SIZE x STD
6 - 8 3 STD LINE SIZE x STD
10 - 12 4 STD LINE SIZE x STD
14 - 16 6 STD LINE SIZE x STD
18 - 20 10 STD LINE SIZE x STD
24 12 STD LINE SIZE x STD
30 14 STD LINE SIZE x STD

1
6

MAINTAIN SAME B.O.P. AS MAINLINE

Ø10 WEEP HOLE

"L" 250

NOTES:
1. ALL DIMENSIONS IN mm
2. DIMENSION "L" TO BE DEFINED ON PIPING ISOMETRIC
3. DO NOT CUT HOLE IN HEADER 2017/03/14
TAG: DS-01-CODE
EXAMPLE: DS-01-A
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2017/02/15 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
DUMMY LEG SUPPORT
DESIGNED J.MEITZ
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2017/02/15 NTS A DS-01 0
 ITEM DESCRIPTION MATERIAL QTY
1 DUMMY LEG TO MATCH SUPPORTED LINE 1
DUMMY LEG NPS & SCH CODE
LINE SIZE NPS
A B
2 1-1/2 SCH80 LINE SIZE x SCH80
3 - 4 2 SCH80 LINE SIZE x STD
6 - 8 3 STD LINE SIZE x STD
10 - 12 4 STD LINE SIZE x STD
14 - 16 6 STD LINE SIZE x STD
18 - 20 10 STD LINE SIZE x STD
24 12 STD LINE SIZE x STD
30 14 STD LINE SIZE x STD

1
6

MAINTAIN SAME
B.O.P. AS MAINLINE
Ø10 WEEP HOLE

"L" 250

NOTES:
1. ALL DIMENSIONS IN mm
2. DIMENSION "L" TO BE DEFINED ON PIPING ISOMETRIC
3. DO NOT CUT HOLE IN HEADER 2017/03/14
TAG: DS-02-CODE
EXAMPLE: DS-02-A
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2017/02/15 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
DUMMY LEG SUPPORT
DESIGNED J.MEITZ
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2017/02/15 NTS A DS-02 0
 ITEM DESCRIPTION MATERIAL QTY
1 DUMMY LEG TO MATCH SUPPORTED LINE 1
DUMMY LEG NPS & SCH CODE
LINE SIZE NPS
A B
2 1-1/2 SCH80 LINE SIZE x SCH80
3 - 4 2 SCH80 LINE SIZE x STD
6 - 8 3 STD LINE SIZE x STD
10 - 12 4 STD LINE SIZE x STD
14 - 16 6 STD LINE SIZE x STD
18 - 20 10 STD LINE SIZE x STD
24 12 STD LINE SIZE x STD
30 14 STD LINE SIZE x STD

1
6

MAINTAIN SAME B.O.P. AS MAINLINE

Ø10 WEEP HOLE

"L" 250

NOTES:
1. ALL DIMENSIONS IN mm
2. DIMENSION "L" TO BE DEFINED ON PIPING ISOMETRIC
3. DO NOT CUT HOLE IN HEADER 2017/03/14
TAG: DS-03-CODE
EXAMPLE: DS-03-A
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2017/02/15 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
DUMMY LEG SUPPORT
DESIGNED J.MEITZ
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2017/02/15 NTS A DS-03 0
 ITEM DESCRIPTION MATERIAL QTY
1 DUMMY LEG TO MATCH SUPPORTED LINE 1
DUMMY LEG NPS & SCH CODE
LINE SIZE NPS
A B
2 1-1/2 SCH80 LINE SIZE x SCH80
3 - 4 2 SCH80 LINE SIZE x STD
6 - 8 3 STD LINE SIZE x STD
10 - 12 4 STD LINE SIZE x STD
14 - 16 6 STD LINE SIZE x STD
18 - 20 10 STD LINE SIZE x STD
24 12 STD LINE SIZE x STD
30 14 STD LINE SIZE x STD

"L" 250

Ø10 WEEP HOLE

NOTES:
1. ALL DIMENSIONS IN mm
2. DIMENSION "L" TO BE DEFINED ON PIPING ISOMETRIC
3. DO NOT CUT HOLE IN HEADER 2017/03/14
TAG: DS-04-CODE
EXAMPLE: DS-04-A
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2017/02/15 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
DUMMY LEG SUPPORT
DESIGNED J.MEITZ
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2017/02/15 NTS A DS-04 0
 ITEM DESCRIPTION MATERIAL QTY
1 DUMMY LEG TO MATCH SUPPORTED LINE 1
LINE SIZE NPS DUMMY LEG NPS & SCH
2 LINE SIZE x SCH80
3 - 4 LINE SIZE x STD
6 - 8 LINE SIZE x STD
10 - 12 LINE SIZE x STD
14 - 16 LINE SIZE x STD
18 - 20 LINE SIZE x STD
24 LINE SIZE x STD
30 LINE SIZE x STD

1
6

MAINTAIN SAME B.O.P. AS MAINLINE

Ø10 WEEP HOLE

"L" 250

NOTES:
1. ALL DIMENSIONS IN mm
2. DIMENSION "L" TO BE DEFINED ON PIPING ISOMETRIC 2017/03/14
3. DO NOT CUT HOLE IN HEADER
TAG: DS-05
EXAMPLE: DS-05
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2017/02/15 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
DUMMY LEG SUPPORT WELDED TO BLIND FLANGE
DESIGNED J.MEITZ
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2017/02/15 NTS A DS-05 0
2016/05/20
2016/05/20
 ITEM DESCRIPTION MATERIAL QTY
1 CENTER PLATE CSA G40.21 (260W MIN.) 1
2 BASE PLATE CSA G40.21 (260W MIN.) 1
3 END PLATE CSA G40.21 (260W MIN.) 2
FLANGE CLASS
PLATE 150# 300# 600#
NPS THICKNESS
INSIDE RADIUS WIDTH INSIDE RADIUS WIDTH INSIDE RADIUS WIDTH
t (mm) R (mm) W (mm) R (mm) W (mm) R (mm) W (mm)
2 9.5 78 123 84 133 84 133
3 9.5 97 151 107 165 107 165
4 9.5 117 178 130 197 139 210
6 12.7 142 219 162 247 181 274
8 12.7 175 265 194 293 214 320
10 12.7 207 311 227 339 259 384
12 19.1 246 375 266 403 285 430
14 19.1 272 412 298 448 308 462
16 19.1 304 458 330 494 350 522
18 19.1 324 485 363 540 379 563
20 19.1 356 531 395 586 415 613
24 19.1 415 613 466 687 479 705

A W
W/4 4 x 22

L
L/4

BASE PLATE DETAIL (Note 4)

90°
R 9.5

t t 6
TYP
6 t H
6 6
t TYP
6

12 A 12 L
W
NOTES:
A-A
1. HEIGHT FROM BOTTOM OF FLANGE TO BOTTOM OF SUPPORT TO BE FIELD DETERMINED.
MAXIMUM HEIGHT H = 150mm
2. LENGTH BASED ON FLANGE WIDTH AND REQUIRED THERMAL MOVEMENT
MINIMUM LENGTH L = 100mm
3. ALL DIMENSIONS IN mm
4. BASE PLATE TO BE WELDED OR BOLTED TO STRUCTURAL STEEL. IF BOLTED REFER TO
BASE PLATE DETAIL FOR DIMENSIONS
5. CONSULT STRESS ENGINEER PRIOR TO USE 2017/03/14
TAG: FS-02-CLASS-LENGTH-HEIGHT
EXAMPLE: FS-02-150-300-100
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2015/12/01 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
FLANGE CRADLE FOR 2-24 NPS ASME B16.5 FLANGES
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2015/12/01 NTS A FS-02 0
2016/05/20
 ITEM DESCRIPTION MATERIAL QTY
1 L SECTION CSA G40.21 (260W MIN.) 2
LINE SIZE NPS L SECTION LENGTH
2 - 3 38x38x6.4 100
4 - 6 64x64x6.4 150
8 - 10 89x89x6.4 150
12 - 14 102x102x9.5 150
16 - 18 127x127x13 150
20 - 24 152x152x16 150

1
TYP
3 TYP 6

NOTES:
1. ALL DIMENSIONS IN mm 2017/08/10
TAG: G-01
EXAMPLE: G-01
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2015/12/01 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
GUIDE FOR BARE PIPE
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2015/12/01 NTS A G-01 0
 ITEM DESCRIPTION MATERIAL QTY
1 SECTION CSA G40.21 (300W MIN.) 2
LINE SIZE NPS SECTION H (mm)
≤ 2 L51x51x7.9 70
3 85
4 100
WT 75x15
6 125
8 150
10 175
12 200
WT 100x23
14 225
16 250
18 275
20 300
24 350
WT 155x39.5
30 425
36 500
42 575

25 X 45.0°
TYP 1 3 TYP

TYP
6

6
TYP
6

NOTES:
1. ALL DIMENSIONS IN mm
2. MAX DESIGN LOAD = 10kN 2018/01/15
TAG: G-02
EXAMPLE: G-02
Pi Engineering
Piping Stress Analysis,
1 SECTION COLUMN REVISED 2018/01/15 SP Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2015/12/01 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
GUIDE FOR BARE PIPE
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2015/12/01 NTS A G-02 1
 ITEM DESCRIPTION MATERIAL QTY
1 L 25 x 25 x 6 x 100 LONG CSA G40.21 (300W MIN.) 2

1 1
TYP.
6

3 GAP
TYP.

NOTES:
1. 5kN MAXIMUM GUIDE LOAD
2. 6mm MAXIMUM LIFTOFF
3. 6 NPS MAXIMUM LINE SIZE
4. MAXIMUM LOAD APPLIES TO GUIDE ONLY, MAY EXCEED ALLOWABLE FOR SHOE
5. CONSULT STRESS ENGINEER PRIOR TO USE 2017/03/14
6. ALL DIMENSIONS IN mm
TAG: G-03
EXAMPLE: G-03
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2016/11/07 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
NARROW GUIDE FOR PIPE SHOE
DESIGNED J.MEITZ
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2016/11/07 NTS A G-03 0
 ITEM DESCRIPTION MATERIAL QTY
1 WT SECTION CSA G40.21 (300W MIN.) 2
LINE SIZE NPS WT SECTION MAXIMUM LOAD (kN)
2 - 10 75 x 14.9 30
12 - 24 100 x 23.1 50
24-36 125 x 40 90

1
3
TYP
EXCEPT INSIDE
6 FACE (TYP)
50

NOTES:
1. STAGGER GUIDES ON ADJACENT LINES IF REQUIRED
2. MAXIMUM LOAD APPLIES TO GUIDE ONLY, MAY EXCEED ALLOWABLE FOR SHOE
3. MAXIMUM LOAD TO BE DETERMINED IF GUIDE HEIGHT EXCEEDS 50mm
4. CONSULT STRESS ENGINEER PRIOR TO USE
5. ALL DIMENSIONS IN mm 2017/01/30
TAG: G-04
EXAMPLE: G-04
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2016/11/07 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
GUIDE FOR PIPE WITH SHOE
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2016/11/07 NTS A G-04 0
 ITEM DESCRIPTION MATERIAL QTY
1 PLATE CSA G40.21 (300W MIN.) 2
MAX GUIDE LOAD
THICKNESS CODE L (mm) T (mm) W (mm) MAX HOLD DOWN LOAD (kN) (kN)
A 40 12.7 6 7 30
B 46 19 9 15 50

12
19

38 W
W

L 19

NOTES:
1. DO NOT WELD GUIDE FACE
2. FIELD TO VERIFY ADEQUATE CLEARANCE TO PREVENT BINDING
3. MAY RESTRICT MOVEMENT OF ADJACENT LINES
4. CONSULT STRESS ENGINEER PRIOR TO USE 2017/03/14
5. ALL DIMENSIONS IN mm
TAG: G-05
EXAMPLE: G-05
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2016/11/07 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
HOLD DOWN GUIDE FOR PIPE SHOE
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2016/11/07 NTS A G-05 0
 ITEM DESCRIPTION MATERIAL QTY
1 PL 19 x 100 x 140 CSA G40.21 (300W MIN.) 2
2 HSS 88.9 x 88.9 x 9.5, 40 LG CSA G40.21 (350W MIN.) 2

12 X 45.0 °

3 SIDES TYP
6 NOTE 4

5
NOTE 3
18
NOTE 3
TYP
6

DETAIL A

40 A
40 NOTE 1
NOTE 1
2

15 (43)
TYP GAP NOTE 5
NOTE 2

NOTES:
1. FABRICATED LENGTH, FIELD OR SHOP TO ADJUST FOR CLEARANCE
2. NON TYPICAL GAPS TO BE IDENTIFIED ON GENERAL ASSEMBLY DRAWINGS
3. REQUIRED MINIMUM CLEARANCE
4. CENTER GUIDES ON STRUCTURAL SUPPORT, DO NOT WELD GUIDE FACE
5. SHOE BASE REQUIRES A MINIMUM OF 43mm EXTENSION FROM SIDE WALL
6. ALL DIMENSIONS IN mm 2017/01/30
TAG: G-06
EXAMPLE: G-06
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2016/11/07 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
HEAVY DUTY HOLD DOWN GUIDE FOR PIPE SHOE
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2016/11/07 NTS A G-06 0
 ITEM DESCRIPTION PART NUMBER
1 UPPER ELEMENT 03SS 13CS W1 mm x L1 mm
2 LOWER ELEMENT 06CHP 13CS 50L W2 x L2 mm
LOWER ELEMENT (ITEM 2) UPPER ELEMENT (ITEM 1)
TAG #
PART # W1 (mm) L1 (mm) PART # W2 (mm) L2 (mm)
LFP-__ 06CHP 13CS 50L 03SS 13CS
LFP-__
LFP-__
LFP-__
LFP-__
LFP-__

W2

W1 TYP
3 3-25 NOTE 4

L2

(9.5mm)

L1

NOTES:
1. BASED ON CON-SERV INC. CHP SLIDE BEARINGS
2. SIZE LOWER ELEMENT FOR CONTACT PRESSURE (MAXIMUM 35MPA)
3. SIZE UPPER ELEMENT FOR MOVEMENT
4. TACK OR STITCH WELD TO MAINTAIN PIPE TEMPERATURE LESS THAN 300°C
5. MAXIMUM CONTACT DESIGN TEMPERATURE 260°C 2017/03/14
TAG: LFP-01
EXAMPLE: LFP-01
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2017/03/07 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
CON-SERV CHP SLIDE BEARING (LOW FRICTION PAD)
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2017/03/07 NTS A LFP-01 0
 ITEM DESCRIPTION MATERIAL QTY
1 FORMED PLATE CSA G40.21 (260W MIN.) 1
2 9.5mm PLATE CSA G40.21 (260W MIN.) 1
LINE SIZE NPS A B C D R T H S BOLT SIZE
1-1/2 71 197 - 49 12 6 15 58 1/2"
2 77 209 - 61 12 6 15 58 1/2"
3 91 238 - 90 12 6 15 58 1/2"
4 104 263 50 115 12 6 15 58 1/2"
6 131 317 68 169 12 6 15 58 1/2"
8 168 390 75 220 20 10 15 58 1/2"
10 203 474 90 274 20 10 24 73 3/4"
12 229 525 90 325 20 10 24 73 3/4"
14 258 583 90 357 20 10 24 73 3/4"
16 283 634 90 408 20 10 24 73 3/4"
18 303 685 103 459 20 10 30 83 1"
20 328 735 103 509 20 10 30 83 1"
22 353 785 103 559 20 10 30 83 1"
24 379 837 103 611 20 10 30 83 1"

4XØH

90 150
T
S
A A 30
2XØH
B

90
1

30 2
SHIM DETAIL D T D 6
R TYP
6

C R 12(TYP)
(C)
SHIM WHERE
REQUIRED
NOTES:
1. OMIT ITEM 2 FOR SIZES 3 NPS AND SMALLER
2. INSTALL SHIMS IF NEEDED SO THAT CLAMP IS SNUG BUT DOES NOT ANCHOR PIPE
3. SIZE BOLT LENGTH ACCORDING TO ATTACHED STRUCTURE
4. INSTALL LOCK-NUTS AGAINST FIRST NUT ON EACH SIDE
5. LINE DESIGN TEMPERATURE TO BE WITHIN -29.5°C TO 200°C.
6. CHECK WITH STRESS ENGINEER PRIOR TO USE 2018/01/04
7. MAY RESTRICT MOVEMENT OF ADJACENT LINES
TAG: PC-01
EXAMPLE: PC-01
Pi Engineering
Piping Stress Analysis,
1 REVISED 'C' FOR NPS 4 2018/01/03 SP Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2015/12/01 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
HEAVY DUTY PIPE CLAMP
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2015/12/01 NTS A PC-01 1
 ITEM DESCRIPTION MATERIAL QTY
1 FORMED PLATE CSA G40.21 (260W MIN.) 1
2 9.5mm PLATE CSA G40.21 (260W MIN.) 1
LINE SIZE NPS A B C D R T H S BOLT SIZE
1-1/2 76 217 - 49 12 6 15 58 1/2"
2 82 229 - 61 12 6 15 58 1/2"
3 96 258 - 90 12 6 15 58 1/2"
4 109 283 50 115 12 6 15 58 1/2"
6 136 337 68 169 12 6 15 58 1/2"
8 173 410 75 220 20 10 15 58 1/2"
10 208 494 90 274 20 10 24 73 3/4"
12 234 545 90 325 20 10 24 73 3/4"
14 263 603 90 357 20 10 24 73 3/4"
16 288 654 90 408 20 10 24 73 3/4"
18 308 705 103 459 20 10 30 83 1"
20 333 755 103 509 20 10 30 83 1"
22 358 605 103 559 20 10 30 83 1"
24 384 857 103 611 20 10 30 83 1"

2xH
ØH

90 150
T
S
2xØH A A 30
B
90
1

30 2
SHIM DETAIL D T D 6
TYP
R 6

C R 12
(TYP)
(C)
SHIM WHERE
REQUIRED
NOTES:
1. OMIT ITEM 2 FOR SIZES 3 NPS AND SMALLER
2. INSTALL SHIMS IF NEEDED SO THAT CLAMP IS SNUG BUT DOES NOT ANCHOR PIPE
3. SIZE BOLT LENGTH ACCORDING TO ATTACHED STRUCTURE
4. INSTALL LOCK-NUTS AGAINST FIRST NUT ON EACH SIDE
5. LINE DESIGN TEMPERATURE TO BE WITHIN -29.5°C TO 200°C.
6. CHECK WITH STRESS ENGINEER PRIOR TO USE
7. MAY RESTRICT MOVEMENT OF ADJACENT LINES 2018/01/04
TAG: PC-02
EXAMPLE: PC-02
Pi Engineering
Piping Stress Analysis,
1 REVISED 'C' FOR NPS 4 2018/01/03 SP Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2015/12/01 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
HEAVY DUTY SLOTTED PIPE CLAMP
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2015/12/01 NTS A PC-02 1
 ITEM DESCRIPTION MATERIAL QTY
1 FORMED PLATE CSA G40.21 (260W MIN.) 1
2 9.5mm PLATE CSA G40.21 (260W MIN.) 1
LINE SIZE BOLT BOLT TORQUE MAX AXIAL LOAD
NPS A B C D R T H SIZE (ft-lb) (kN)
1-1/2 71 197 - 49 12 6 15 1/2" 30 20
2 77 209 - 61 12 6 15 1/2" 30 20
3 91 238 - 90 12 6 15 1/2" 30 20
4 104 263 50 115 12 6 15 1/2" 30 20
6 131 317 68 169 12 6 15 1/2" 30 20
8 168 390 75 220 20 10 15 1/2" 30 20
10 203 474 90 274 20 10 24 3/4" 80 40
12 229 525 90 325 20 10 24 3/4" 80 40
14 258 583 90 357 20 10 24 3/4" 80 40
16 283 634 90 408 20 10 24 3/4" 80 40
18 303 685 103 459 20 10 30 1" 130 50
20 328 735 103 509 20 10 30 1" 130 50
22 353 785 103 559 20 10 30 1" 130 50
24 379 837 103 611 20 10 30 1" 130 50

4XØH

90 150
T

30
A A
B

2
D (D-T) T D 6
TYP
R 6

C 12
R (TYP)
(C)

NOTES:
1. OMIT ITEM 2 FOR SIZES 3 NPS AND SMALLER
2. ENSURE GAP EXISTS BETWEEN CLAMP AND STRUCTURE SO CLAMP ANCHORS PIPE
3. SIZE BOLT LENGTH ACCORDING TO ATTACHED STRUCTURE
4. INSTALL LOCK-NUTS AGAINST FIRST NUT ON EACH SIDE
5. LINE DESIGN TEMPERATURE TO BE WITHIN -29.5°C TO 200°C.
6.
7.
CHECK WITH STRESS ENGINEER PRIOR TO USE
MAY RESTRICT MOVEMENT OF ADJACENT LINES
2018/01/04
TAG: PC-03
EXAMPLE: PC-03
2 REVISED 'C' FOR NPS 4 2018/01/03 SP Pi Engineering
Piping Stress Analysis,
1 REMOVED S COLUMN 2016/10/27 SP Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2015/12/01 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
HEAVY DUTY PIPE CLAMP ANCHOR
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2015/12/01 NTS A PC-03 2
2016/05/20
A

2016/05/20
A

2016/05/20
2016/05/20
 ITEM DESCRIPTION MATERIAL QTY
1 U-BOLT: SIZE PER NPS, C/W NUTS CARBON STEEL 1

LINE SIZE NPS LISEGA PART NO. U-BOLT ØD (mm) THREAD SIZE (inches)
1 40 03 .8 34 1/4 UNC x 2-3/8
1.5 40 05 .8 48 3/8 UNC x 2-1/2
2 40 06 .8 60 3/8 UNC x 2-1/2
3 40 09 .8 89 1/2 UNC x 3
4 40 11 .8 114 1/2 UNC x 3
6 40 17 .8 168 5/8 UNC x 3-3/4
8 40 22 .8 219 5/8 UNC x 3-3/4
10 40 27 .8 273 3/4 UNC x 4
12 40 32 .8 324 7/8 UNC x 4-1/4
14 40 36 .8 356 7/8 UNC x 4-1/4
16 40 41 .8 406 7/8 UNC x 4-1/4
18 40 46 .8 457 1 UNC x 4-3/4
20 40 51 .8 508 1 UNC x 4-3/4
24 40 61 .8 610 1 UNC x 4-3/4

ØD

3 GAP

EXISTING STRUCTURAL STEEL

NOTES:
1. LISEGA PARTS CAN BE EXCHANGED WITH EQUIVALENT
2. DO NOT ANCHOR PIPE
3. CHECK FOR INTERFERENCE WITH ADJACENT PIPES OR GUIDES
4. MAXIMUM LINE TEMPERATURE 80°C 2017/01/30
TAG: UB-01
EXAMPLE: UB-01
Pi Engineering
Piping Stress Analysis,
Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2015/12/01 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
GUIDED U-BOLT SUPPORT
DESIGNED M.BROOK
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2015/12/01 NTS A UB-01 0
 ITEM DESCRIPTION MATERIAL QTY
1 U-BOLT: SIZE PER NPS, C/W NUTS CARBON STEEL 1

LINE SIZE NPS LISEGA PART NO. U-BOLT ØD (mm) THREAD SIZE (inches)
1 40 03 .8 34 1/4 UNC x 2-3/8
1.5 40 05 .8 48 3/8 UNC x 2-1/2
2 40 06 .8 60 3/8 UNC x 2-1/2
3 40 09 .8 89 1/2 UNC x 3
4 40 11 .8 114 1/2 UNC x 3
6 40 17 .8 168 5/8 UNC x 3-3/4
8 40 22 .8 219 5/8 UNC x 3-3/4
10 40 27 .8 273 3/4 UNC x 4
12 40 32 .8 324 7/8 UNC x 4-1/4
14 40 36 .8 356 7/8 UNC x 4-1/4
16 40 41 .8 406 7/8 UNC x 4-1/4
18 40 46 .8 457 1 UNC x 4-3/4
20 40 51 .8 508 1 UNC x 4-3/4
24 40 61 .8 610 1 UNC x 4-3/4

ØD
U-BOLT TYPE 40

EXISTING STRUCTURAL STEEL

NOTES:
1. LISEGA PARTS CAN BE EXCHANGED WITH EQUIVALENT
2. CHECK FOR INTERFERENCE WITH ADJACENT PIPES OR GUIDES
3. MAXIMUM LINE TEMPERATURE 80°C 2017/05/18
TAG: UB-02
EXAMPLE: UB-02
Pi Engineering
Piping Stress Analysis,
1 REVISED NUT LOCATION 2017/05/18 SP Piping Engineering, Finite
Element Analysis (FEA)
0 ISSUED FOR CONSTRUCTION 2015/12/01 SP
DESCRIPTION
REV REVISION DETAIL DATE APR'D
ANCHOR U-BOLT SUPPORT
DESIGNED J.MEITZ
APPROVED S.PHELPS
SCALE SIZE DWG NO. TYPE REV
DATE (YYYY/MM/DD) 2017/05/18 NTS A UB-02 1