APL SPCOIGATION 17D, 180 196264 7 6.4 Marking ‘The subsea tree assembly shall be tagged with a nameplate labelled as “Subsea tree assembly’, iocated on the master valve or tree valve block, and contain the following information as a minimum: name and location af assembleridate; — PSL designation of assembly: rated working pressure of assembly — temperature rating of assembly: material class of assembly (including maximum H2S partial pressure i applicable): unique identifier (serial number); — 180 136284. 6.5 Storing and si Any disassembly, removal or replacement of parts or equipment after testing shall be as agreed with the purchaser. ‘The shipping weight of the subsea tree, including balance weights, should be kept to a minimum. In many cases, ‘maximum lift weight can be restricted by rig-crane limitations in accordance with local legislation or regulations. 7 Specific requirements — Subsea-tree-related equipment and sub assemblies 7.1 Flanged end and outlet connections TAA General — Flange types |=SlauseNOTE1 SECTION 7 spenifies the ISO (API) type end and outlet flanges used on subsea completions equipment. Table 6 lists the types and sizes of flanges covered by this parteH1S0-42628 SPECIFICATION Table 7 5 — Rated working pressures and size ranges of ISO (API) flanges Rated working Flange size range pressure Type 1788 Type 178V Type 68x mea | tos) | mm in mm (in) mm (in) ‘345 | (8000) | S2i0346| (Zimelo | S2t056 | (2velo1SS~e) | sMBt>S40 | (1S8~t021 vA) 1358) a0 | (10000) | — = 4610946 | (1 isitoto 1358) | 4610540 | (1 tat0t0 21 1) 1038 | (15000) | — = = = 4610408 | (1 isnet0 18 44) Standard flanges for subsea completion equipment with working pressures of 34.5 MiPa (5 000 psi) and below in sizes of 52 mm (2 1/16 in) ti mm (13 5/8 in) shall be type 17SS flanges as defined in 7.1.2.2.48 Desion ano OPERATION OF SUBSEA PRODUCTION SYSTENE, Past 4: SUBSEA WELLHEAD AND TREE EQUPMENT shall conform to Table 7, Tabie 9, Table 10, and Table 11. Standard flanges for 34,5 MPa (5 000 psi -eme-betow in sizes of 346 mm (13 5/8 in) through $40 mm (24 1/4 in) shall be type 6BX flanges es defined in 480-40423. AP! 6A Standard flanges for subsea completions with maximum working pressures of 69 MPa (10 000 psi) ar 103,5 MPa {15 000 psi) shall be type BX flanges as defined in {S@-40423 API 6A ASCAPI-Yype flanges for subsea completions may be either integral, blind or welding neck flanges, Threaded flanges, as defined in 1$0-40423 API 6A, shall not be used on ‘subsea completion equipment handling produced fluids, except as specified in 7.3, Segmented flanges shall not be used. NOTE? Swivel flanges are often used to facilitate subsea flowline connections that are made up underwater. Type 17SV flanges, as defined herein, have been developed as the standard swivel-flange design for subsea completions in the sizes and working pressures given in Table 78. Type 17SV swivel flanges are designed to mate with standard APIIS6-type 17SS and type 6BX flanges of the same size and pressure rating 7A.2 Design 7121 General All flanges used on subsea completions equipment shall be of the ring-joint type designed for face-to-face make- up. The connection make-up force and external loads shall react primarily on the raised face of the flange. ‘Therefore, at least one of the flanges in a connection shall have a raised face All flanged connections that are made up underwater in accordance with the manufacturer's written specification shall be equipped with a means to vent any trapped fluids. Type SBX ring gaskets, as shown in Table 86, are an acceptable means for venting type 6BX, 17S, or 17SV flanges. Type SBX or 180-18423API GA-type BX ring gaskets, are acceptable for 6BX, 1735 or 17SV flanges made up in air Other proprietary flange and seal designs that eliminate the trapped fluid problem have been developed and these are, therefore, well suited for underwater make-up. These proprietary flange and seal designs shall comply with TA Trapped fluid MAVean-alge interfere with the proper make-up of studs ar bolts installed into blind holes underwater. shroaded-hole-andiorthe stud} if installed underwater, a means should be provided to confirm that bolting has been fully engaged in the blind Nole or a means to vent trapped fluid from behind the installed botting7.1.2.2 Ring Gaskets Types 6BX, 17S, and 17SV flanges in subsea completion equipment shall use types BX or SBX gaskets. If these flanges are made up underwater, they shall be made up with SBX gaskets, in accordance with TAZA. Connections that are not made up underwater may use nonvented type BX gaskets. Gasket material shall be of a corrosion-resistant alloy (CRA) or corrosion-resistant material (CRM) to provide corrosion resistance to seawater under the specified operating conditions (dissimilar metal corrosion with the ring groove). Gasket materials shall conform to the requirements of API 6A. The thickness of coatings and platings used on BX and SBX ring gaskets to aid seal engagement while izing galling shall not exceed 0.0005 in. (0.013 mm). The use of coatings that can be harmful to the environment or galvanically active should be avoided. Local legislation should be checked for coatings deemed hazardous. Proprietary gaskets shall conform to the manufacturer's written specification. Grease shall not be applied around the complete perimeter to hold ring gaskets in position during makeup, since grease can interfere with proper make-up of the gasket. Tack welding rods to the OD of seal rings (to simplify positioning of the ring during make-up) shall not be used on gaskets for subsea service. Except for testing purposes, BX and SBX ring gaskets shall not be reused.“Table £0 — AP! type SBX prossure-energized ring gaskets rte tr abt Kes Tolerances, express mimes inenes) Hebe (mm) +0/-0.006 (+0/-0.15), +002 (40.05), 40,008 /-0(+0.15/-0) (ODT, cutie dameterT 3 wath ttt i | | i 4 rads inna SEE NOTET 0 nator 40,008 /-0 (20.210) 64° wth ofrng 40,008 0 (40:21) 7 depot prove hone, -ccom.02 / 0 (0.51.0) cutsée depth of gone 3k wetnatgroe 10% radusin rove 40,0040 (40.17-9) 0,004 /.0 (20.1.0) MAX 11 srencsnarp comer NOTE Rague tehat bo 851072 of he goat alg NOTE2 Two pressure passage holes inthe SX rng cous-seton seven fesse ck when conneatons fe made up urdermatr Th options we ‘vic tor eng peers passage Maes (EE ro -“Table 6 (contnued) Tognm] Be] Saat] taper | wan [emma] maha [ices [ong | Bote Sera | MoE sous [oe ser] ca faze waar oz ecg] cea for] ary oe war [te |aer | (ae we |e 72s | ee [0 [os | a6 foe Tom | re |r fa 3 758 |e] 18 | a 98x 159 {2 ons} | x00,o4 (9,74) | 11,38 (0,448; | 11,98] 0.448) o0.31 | (o.oo 0,76 | 10,306] a soa77 | 306) sori] re pave | Heat] em [Ao] oe | 2.0] oan |nsasteon [tse] eal] ss|ean]] Toe 78a — sores [or [a terse] cm |tao[ioso| uz] onoyc| aren [uzaloanl|ssfeonlf x am Sees | oe [in| nas [rors | Boas eras] aso a [axal|irar [wen | tn ceo soxsee_| se | | 329725 | 1220s 2 Oa 57>49] eo 222[ er] 5 [oon] 959 | 0351 | 7aera0 cea res | at ine 02 aaaPy{cer|oss so) aa wor Yorn: | seas axa sek 0 | tesa mom agar so] eal |epe Love] era com ea a wn [rasnf wa sao gual als] s [Astron 08m 008 wh fd npr eid evi hy Sa so, OE rhodeAPI SPECIFICATION 17D, 180 19628-4 5 fom art Tablas Fant 8 rat-the-modified-integrat Threaded fanges-s pletions-equipment-exceptas-pr onda 71.2.34 Standard subsea flanges — Type 6BX with working pressures of 69 MPa (10 000 psi) or 103,5 MPa (15 000 psi) Standard flanges for subsea completion equipment with a working pressure of 69 MPa (10 000 psi) or 103,5 MPa (15 000 psi shall CONFORM -eompiy-with TO the requirements for type 6BX flanges, a8 defined in 4S0-4423-AP1 6A, ‘These flanges are ring-joint-type flanges, designed for face-to-face make-up. The connection make-up force and external loads shell react primarily on the raised face of the flange. Corrosion-resistant, inlaid ring grooves for type 6BX flanges shall comply with the requirements of $0-48423 API 6A. 7.1245 Special-purpose subsea flanges — Type 17SS with working pressures of 103,5 MPa (15 000 psi) cor 120,7 MPa (17 500 psi) ‘Spocial-purpose 25mm (1 in) flanges for use with a working prossure of 103,6 MPa (15.000 psi) or 19 mm. (0.75 in) flanges for use with a working pressure of 120,7 MPa (17 500 psi) for subsea completion equipment shall CONFORM TO eamply-with the requirements for type 6BX flanges. as defined in Table& 10. These-flanges_are-rn7.1.2.3 Corrosion-resistant Ring Grooves All end and outlet flanges, and flanged connections used on subsea completion equipment shall be manufactured from a CRA, or their ring grooves overlaid with a CRM/CRA material, per 5.3.3, to provide corrosion resistance to seawater under the specified operating conditions. Prior to application of the overlay, preparation of the BX ring grooves shall conform to the dimensions in Table 12 or API 6A. The overlay material shall be compatible, in accordance with the manufacturer's written specification, with retained fluids and with both the base metal of the flange and the gasket material (surface hardness, galling, and dissimilar metals corrosion). 7.1.2.6 Standard Subsea Flanges—Type 17SS with Working Pressures of 5000 psi (34.5 MPa) 7.1.2.6.1 General 24/16 in, (52 mm) through 11 in. (279 mm) type 17SS flange designs are based on type 6B flange designs as defined in API 6A, but they have been modified to incorporate type BX ring gaskets (the established practice for subsea completions) rather than type R or RX gaskets. In addition, type 17SS flanges shall be designed with raised faces for rigid face-to-face make-up, 5000 psi (34.5 MPa) typo 17SS flanges shall be used for all 21/16 in. (52 mm) through 11 in. (279 mm) subsea completion API-type flange applications at or below 5000 psi (34.5 MPa) working pressure. 135/8 in. (346 mm) through 211/4 in. (540 mm) standard subsea flanges for working pressures of 5000 psi (34.5 MPa) and below shall be type 6BX flanges as defined in API 6A. 7.1.2.6.2 Dimensions 7.1.2.6.2.1 Standard Dimensions Dimensions for type 178S flanges shall conform to Figure 6 and Table 9, Table 10, and Table 11 Dimensions for ring grooves shall conform to Table 8 through Table 12 or API 6A. Type 17SS flanges used as end connections on subsea compietion equipment may have entrance bevels, counterbores or recesses {o receive runningjtest tools, plugs, etc. The dimensions of counterbores and recesses are not covered by this specification but shall not exceed the B dimension given in Table 9 and Table 10. 7.1.2.6.2.2 Integral Flange Exceptions The manufacturer shall ensure that the modified integral flange designs shall meet the requirements of Section 57.1.2.6.2.3 Welding Neck Flanges—Line Pipe The following conditions shall apply. a) Bore and wall thickness—The bore diameter, JL, shall not exceed the values given in Table 11. The specified bore shall not result in a weld end wall thickness less than 87.5 % of the wall thickness of the pipe to which the flange is being attached. b) Weld end preparation—Dimensions for weld end preparation shall conform to Figure 8. c) Taper—When the thickness at the welding end is at least 0.09 in. (2.3 mm) greater than that of the pipe and the additional thickness decreases the inside diameter (ID), the flange shall be taper-bored from the weld end at a slope not exceeding 3 to 1. NOTE Its not intended in this specification that Type 17SS welding neck flanges be welded to wellheads or tree bodies. Their purpose is to provide a welding transition between a flange and a pipe.API SPECIFICATION 17D, 180 19626-4 Table 7 9 — Basic flange and bolt dimensions for type 17SS flanges for 34,5 MPa (5 000 psi) rated working pressure Gan 652 Et tie, 5 48 "| 8 3mm 0.42 in} min Break sharp comers. nm (0,189) 1,5 mm (2.08 ring gr2ove shell be conceritie with tore within D3 my (0.040 in total inceator runout Bot hole contating locates within 0.8 mn (0,03 in) of tsoratea’ B.C. and Bal Roles wth equal pacing, 40.2)Table? coninved wecton| ee |ranaes raat re Oapatct Bam at | Batre | Langa wnt fe amie [am| se ee] [vem erm wa|ran|aelnan|wa]ea| «=o = an] jem) elem De ‘Table #10 — Basle flange and bol dimensions for 19 mm (34 in) and 25 mm (1 In) type 17SS flanges ae eee oo» ee ar pa ateAPI SPECIFICATION 17D, 180 19628-4 Table 911 — Hub and bore dimensions for type 1788 welding neck flanges. for 34,5 MPa (5 000 psi) rated working pressure om eh ' 4 | - | | | NOTE See Table 7 for diversions 8, 0. and Tard forthose rok shown Nomina size Neck diameter of Tolerance for Maximum bore ond bore of ‘relding neck of welding neck flange ‘tango ange % £076 (0.03) mm o om 7 om wo om ia) = ein) eos) (aa) 2 om 130 789 7 ? & (888 ee) 6 en) 32 | a8) a om Bal @13) & | (88 98 (B18) 88,9 (3,50) +2 (eos 66,5 (2,62) & 88 toa | etna | 14a | (50) 2 ae | eae) 0] im | ane | eam) % ws) ean wo | wma | 604 | (05) ’ a] G9) 28 @ zea | a) | os 1730 | an 278 a zea | 680) we | Gee | azn | ieee) |e, aia | 36t)56 DESIGN ANO OPERATION OF SUBSEA PRODUCTION SYSTEMS, PART 4: SUBSEA WELLHEAD AND TREE EQUPMENT Neer ff NOTE 2 (718) Figure 8 — Weld end preparation for types 17SS and 17SV welding neck flangesAPLSPECIFICATION 17D, 180 19628-4 El #4257 Swivel flanges — Type 178 for working pressures 34,5 MPa (5 000 psi) or 69 MPa (10 000 psi) FARE T1271 General ‘Type 17SV flanges are multiple-piece assemblies in which the flange rim is free to rotate relative to the flange hub, A retainer groove is provided on the neck of the hub to allow installation of a snap wire of sufficient diameter 10 hold the ring on the hub during storage, handling and installation. Type 17SV flanges may be used on subsea completion equipment whore Its difficult or impossible to rotate either of the flange hubs to align the mating bolt, holes. Type 17SV flanges mate with standard types 6BX and 178S flanges of the same size and pressure rating, NOTE Type 17SV swivel flanges are of the ring-joint type and are designed for face-to-face make-up (SEE FIG. 9) ‘The connection make-up force and external loads shall react primarily on the raised face of the flange. Fh&b27.4.2.7.2 Dimensions Dimensions for type 17SV flanges shall conform to Tables +4 13 through 44 16. [Dimensions for welding neck preparations shail conform to Figure 8 and Table + 13. Dimensions for ring groves shall conform to Tables 6 8 and-40 12. FA887.1.27.8 Flange faco Flange faces shall be fully machined. The nut bearing surface shall be parallel to the flange gesket face within 1°. The back face may be fully machined or spot faced at the bolt holes, The thickness of type 1788 flanges and type 17SV hubs and swivel rings after facing shall meet the dimensions of Tables #8; 9, 10 and +t 13 through 44 16, a8 applicable. The thickness of type 6BX flanges shall meet the requirements of }SO-0423. API 6A. vee one _ a é ee sieges 2:56 7.1.2.7.4 Flange materials nform-to-the requirements if a rine 4 if sa "the swivel flange materiais shall conform to the requirements in 6.2 and 6.3. A minimum yield strength of 75,000 psi (517 MPa) shall be used for type 17SV flanges for 10,000 psi (69 MPa) RWP. The clamp hub Portion of a 17SV flange shail conform to 7.2hub (see Tables 13 and 15) SBX or BX ring gasket ring (see Tables 14 and 18) closure bolting retainer ring mating API 6BX flange butt weld (see Figure 8) mating AP! 68X studdad connector component welded to hub Figure 9—Assembled Type 17SV Flange.Groove location, . 3 (000 Groove radius, ot “St (“Y Desion ano OF VATION OF SUBEEK PRODUCTION SYSTEMS, PART 4: SURGEA WELLHEAD AND TREE EQUIPWENT Table 44 13 — Hub and bore dimensions for type 178V flanges - USC UNITS ore : rong \ || Para | 9 (0.125) le") Break sharp comers. Hub? and bore dimensions. Nominal Outside Total Large | Lengthof | Groove | Retainer Ring ‘and bore ameter | thickness diameter af | neck location | gre gasket nock us| no, OD, r 7 Z uy, GR Bx. mm [ tin) [mm [ny (a) am] tn) _[mm) tn (ny [om [inp 52 [2 wise) [128 | 6.031) [95 [Ft 33 [13.866 [64 Ty 74 [@s07)| 8 [10.128)] #82 05. | (26) | 147 | (6.761) | 29,5 | (1,766) | NPSL Ga <08) %3.282)| 74 [(2,907)| 3 [(0,125)| 153 73 | (319) | 160] (6.312) | 295 | (1.156) | 126 | a8 | (3.432)| 7a | 1.067) 3 |t0.125)| 154 103 | (4 v6) | 194 | (7,625) | 90,5 | (1.197) 76.250) 3.757) | 86 [(3.382)| 3 [(0,125)| 155 130 | S10) [240 | (0.380) | 36.0 | CLgsehT 107 | «7.755) | 121 |e in [iaas7)| 3 [oo.t2s)| 269 179 | (7 16) | 272 [(10,700) | 4psT1.922) | 231 | (9,075) | 141 | 15,584) ora) 5 [10,188] 158 zae| e340 | ragpprar.s [ 7.622) | 206 [ (11,628) | 156 | 6.178) | 747 | © 5_| 10.768) [ 767 za (11) F250) | 42.0 | (1,854) | 372 | (14,625) | 162 | v6.932) | 162 | (6.370) 0,188) | 158 346 | (43 sppar8%4 | (20,625) | 27.52 | (1,871) | 489 | (19,000) | 182 | 17,190) | 108 | 6.614) | 5 [> +60 g ‘al svength shall be equal fo or greater than 517.1 MPa (75 000 psNOVA TABELA Hub Dimensions for 17SV Flanges for 5000 psi Rated Working Pressure—USC Units Dimensions in inches Maxinwum | Outside Groove | Retziner Nominal Groove aay Bore | Diameter Location | Rroove (my L ue GR Tolerance: Minimum | +0.030-0 | +0.006-0 12s | Bx-182 ars | Bx-183 ozs | Bx-184 ozs | Bx-186 778 128 | Bx-t89 2.07 area | Bx-156 a 1 11.82 osea | Bx-157 1" 1103 18.25 1.85 1482 7 oes | Bx-158 13% 13.88 20.82 187 19.00 718 ects otea | Bx-te0 Hub Dimensions for 17SV Flanges for 10,000 psi Rated Working Pressure—USC Units Dimensions in inches Nominat | Maximum | outside | totat | 42700 Groove | Retainer Se gees |inemear: [Nixes | De (Saten| Soe (in) 2 ‘oD r z L ue GR Tolerance: | Maximum vo.oa0 | +0030 | minimum +0.0051-0lo 12 — Basic dimensions of rings and bolts for type 17SV flanges for 34,5 MPa (5 000 psi) rated working pressure Dmonsens inline (ache) unk Tolerances (outside diameter) Sizes 2716105 18 sot0.062 in) Sizes 7 161011 mm (0,125) RE (onathof ring 3mm (39) mm $3) (rge10 ring umm 2° in ps wont © (chamter) £32 amen “92" i) Bol lame Sizes 2 1610 7 116 Szes 91011 36 mm 2888)NOVA TABELA Table 14—Ring Dimensions for Type 17SV Flanges—USC Units [Dimensions in inches RE length of ting) 942% 9, (“2mm RT epth of xge +1002, (2) diameter) o C5 J (large-ID ring) $0031 9, (3 om) RID (gmalHID ring) °°93F ("7 ae) Bolt diameter: Sies2 toto 7 his “BED in, (78% mm Sizes 9 to 11 20.000 in, (25 un)Ring Dimensions for Type 178V Flanges for 8000 psi Rated Working Pressure—USC Units Dimensions in inches Depth Nominat | Diameter | , 2f Sonat Chamter Hote | nor ‘Size ofRing | trae of Ring Qty. | Bolt Holes (in) ‘ROD ar En r Tolerance: | +0.000-0 +008/-0 ts 2.50 72 ee 447 6.00 11.89 vas | test | 14.00 13s 2080 1s7 | 2002 | 18.00 Ring Dimensions for Type 178V Flanges for 10,000 psi Rated Working Pressure—USC Units Dimensions in inches Depth aa Outside Diameter of Ring Gr | target | sman io Diameter of uaige | ortag | ering enamter | chete | Hole | “Gon ttiee 1D ty. 20D ar BL En Tolerance: | +0.06"-0 oso | 03-0 1h 7.38 asoz | 331 Dee 7, | sosz | 381 ne 2.862 athe e002 aleHub Dimensions for 178V Flanges for 34.6 MPa Rated Working Pressure—SI Units. Dimensions in milimeters Large Retainer Nominat | Maximum | Outside | Tota | Qi 278 | Length of Se = Bore | Diameter | Thickness | “Sein, | Neck ‘aadiiee 5 T £ GR Tolerance: | Maximum Minimum a4 a4 TRE 88 103.0 98 131.1 120 180.1 2 141 1265 2284 186 141.0 220.2 413 18 118 37.0 524 478 483 182 162.0 Hub Dimensions for 178V Flanges for 69.0 MPa Rated Working Pressure—SI Units Dimensions in milimaters Retainer Groove Radius Nominal | Maximum | Outside Total Length of | Groove ‘Size Bore | Diameter | Thickness Neck | Location in} z oD L af GR Tolerance: | Maximum a Minimum he 487 84 84 24Table 16—Ring Dimensions for Type 17SV Flanges—SI Units Dimensions in millimeters @.X THRU, (Y) HOLES EQUALLY SPACED RaoL0sRing Dimensions for Type 178V Flanges for 34.5 MPa Rated Working Pressure—S1 Units Dimensions in milimaters Outside | Depth Number Nominal | pismeter chamfer of Bolt Size | of Ring Holes (ing Diameter of Bolt Holes, ROD a Fr Tolerance: | +2/-0 4 33:0 X Figure the 1203 82 2he 1484 a athe 44 | te20 a8 24 | 1053 76 a5 207 | 2208 a 204 ger | 2734 114 483, se1 | s382 128 38% 85 aes | 4144 140 482.8 e73 aa | sana 154 500.8 Ring Dimensions for Type 178V Flanges for 69.0 MPa Rated Working Pressure—S1 Units Dimensions in milimetars Sze | otning | iy Beles ‘ROD ar Tr = Tolerance: Figure Ph @ 88 (St 00030 ean 111s Ue ager Hy] 088 6] 09] va Zar ver B sea (ose) | on vele 6m - 068 s 2 | et 962 Vee sue s_ | ew @ 96 ves | toose | 66 061 Zoe ee e [Gee ge (Gee0) [ese zoe e [i @ woo | sve 05h teva | eo oeo | sre seh [sre |e Geso) | she ay a ws | | ww | ON Lae > 18 1 ia ajo 0109 “wpe yoqieiseuryg | 2HUEYO Sujousuey | Sunjociews | Buuyoaie6iey | aisTONEeD | asc omanc | PEA RUMON 08 (panugues) zi a1qeL “NaWaMIOg SSu CNV GYSNTISN WASONG ip LNG AGISAG NOUSNOOUd WEEN 40 NOUISAO GNV NOISEAPL SPECIFICATION 170,180 19628-4 63 Table 13 — Hub dimensions for type 17SV flanges for 69 MPa (10 000 psi) rated working pressure Dimensions in milimetrasafRches) Hub* dimensions Nominal size side Total | Large diameter] Length of | Groove fetainer | Ring ‘andbore | diathajer | thickness | of neck neck location arocve | gacket oD T J L RG Bx mm] ce) [mm] tiny [mm NG | mm [iy mm | pA mm] ir) [mm] tin) 46 | (1 r31t8) [115] (4.500) [29.5 | (1.180) 22.6 | (9,250) 282)| 74 | (2,907)| 3 |0.128)| 151 52 | (216) | 130 | (6,000) | 29.5 | (1,186) (3.75974 [(3,282)| 74 [i2907)| 3 [00.125] 152 65 | (2are) | 150 | (6.800) | 29.5 | (1,166) | 115.6 | Sy6o) | 84 | (3.302)| 75 | (227) 3 [co.r26)| 159 78 | (3119) | 175 | (6.930) | 30,5 | (1.197) | 145] 680X193 | (3,608) 84 [(@.29| 3 [io.t25)[ 154 103 | ane) | 215 | (e437) [33.3 | (1.a1pA7e0| (6.812) | HAYa.27)| 99 | (a.902)| 3 [io.r28)| 155 x30] vay [225] (960) | 38.1 eSo0) | 211,7| (6.995) | 121 | ae] 111 4.357) | 3 [c0.125)| 169 79 | «746 | 350 | (13,660) (1,652) | 305,7 | (12,035) | 158 | (6.204) NN | 6.647)| 5 [(0.188)| 156 228| (9) | 415 | (re ga6h] 4200 | (1,653) | 371.5 | (14,625) | 185 | (7,270)| 170 Nego7)| 5 [(o.188)| 197 27a (11) _[ 4sq)efe.a70)| 51,7 | 2,035) | 438,0 | (17,245) | 207 | (8.183) | 193 | 7.595 [0.188)| 158 346 | (13 sie) 665 | (22,250) 58,7 | 2,309) | 523,9 | (20,625) | 242 | (2,531) | 228 | (8,969) 0,188)| 159 = Hus pera strength shall be equal oor greater than 517,1 MPa (75 000 ps)6 DESIGN ANO OPERATION OF SUBSEA PRODUCTION SYSTEMS, PART 4: SUBSEA WELLHEAD AND TREE EQUPMENT Table 14 — Basic ring and bolt dimensions for type 17SV flanges for 69 MPa (10 000 psi) rated working pressure Dimensions in millimetres (inches) unless otherwise ipficated mh Tolerances s——4 = R (outside diameter) Oe te REY Sizes 2 111610 5 118 +219 (0,062 in) 7 Sizes 7 1/16 to 11 +i mm (0,125 in) <4 7 RL (length of ing) 3 mn 25 in) ; RT (depth of arge diafber) °3 mm (°° in) % ay “4 mm {$0031 is s|< _—It_IN oe 3 8] | R17 (largetD rin dmm( 9°" in) ele RI iw s . s RI2_ (small-Ifing) “4mm (“309 in} t - +103 40,010 (PST c (eyfafer) 23 mm (19019 in) Y | Bolt plameter: “4928 in) Sizes 2 1/16 to 7 1/16 ~ Sizes 9 to 11 235 mm ( 13858 in) Basic dimensions of ring® Bolts Large 1D ofring | SmalliD ofring | Length ofting| cham | Diameter of bolt] Number | Diameter of circle | of bolts | bolt holes Ri Riz RL ¢ BC mm | tm) | mm | tm) lm] tm [mm] om 7m mm | tn) nis9 | 562) | oa | ary] os | eas | 3 [225 | wed] G75 | @ | 2 | 2s) 266 | 6.062) | 968 | aya | os | asm | 5 | 0.125) | 1588. Nos | 8 | 23 | oa) 148,9 | (6,862) | 117.1 1612) | 63 | (2,470) | 3 | (0,125) | 184,1 | (7B) 8 26 | (1,00) 778 | (6992) | a 6742) | 72 | eas | 3 [0225 |259| sone | 2 [asa 215,9 | (8,500) | 44.6 | (6,875) | 88 | (3.445) | 3 | (0,125) | 258,8 | (10,19) 8 32_| (1.25) 2548 | (10.022) Vora | 18.387) | 99 | (900) | 3 _| (0.128) | s000 | (1.81) x2 | (1.25) 3485 | (13,79 | 307.3 | (12,097) | 490 | 6.12) | 5 | (0.188) | 403 | (1598) | _12Q] a2 | Gea) 2097 | (ight) | 373 | (14.687) | 158 | 188) [ 5 | (0.188) | e963 | cars) | 16 Nee | (182) 280.9 |fe.932) | 4396 | 17.307) | 100 | (07a) | 5 | (ote) | 5052 | @a2s)| 16 (88) 5667} (22.312) | 525.4 | (20,687) | 215 | (8.450) | 5 | (0.188) | 673,1 | (26,50) 20 512.00) = Hing material strength shall be equal ‘oor greater than 517,1 MPa (75 000 psiAPLSPcORICATION 17D, 180 19626-4 6 7.2 ISO clamp hub-type connections ‘API clamp-hub-type connections for uso on subsea completion equipment shall comply with the dimensional requirements of SO 13533. All end and outlet clamp hubs used on subsea completion equipment shall have their ring grooves either manufactured from, or inlaid with, corrosion resistant materials. Corrosion-resistant inlaid ring grooves for clamp hubs shall comply with ISO 13533 (or lo Figure 7 and Table 6 if BX or SBX gaskets are used). Overlays are not required If the base material is compatible with well fluids, seawater, etc. NOTE For the purposes ofthis provision, AP! Spec 16A is equivalent to ISO 13533 (alt parts) For forged material used for pressure-containing and high-load-bearing parts, forging practices, heat treatment and test coupon (QTC or prolongation) requirements should meet those of AP! RP SHT. In addition, the test ‘coupon shall accompany the material it qualifies through all thermal processing, excluding stress relief. 7.3. Threaded connections Loose-threaded flanges and other throaded end and outlet connections shall not be used on subsea completion ‘equipment, except for tubing hangers, that handles produced fluid. Threaded flanges may be used on non- production connections, such as injection piping, provided there is an isolation valve and either a bolted flange or a clamp hud connection on the tree side of the threaded flange. Integral threaded connections, such as instrument connections, test ports, and injection/monitor connections, may be used in sizes up to 25,4 mm (1.00 in), provided they are used in conjunction with the appropriate rated working pressure defined in Table 2 and ISO 10423 and are located downstream of the first wing valve. If threaded connections are used upstream of the first wing valve, there shall be an isolation valve and either a bolted flange, clamp hud or welded connections as defined in 7.20.2.6 on the tree side of the threaded connection. Threaded bleeder/greaselinjection fittings shall be allowed upstream of the first wing valve without the isolation valve and flange/clamp hub if at least two pressure barriers between the produced fluid and the external environment are provided. The sealing areas shall be made of corrosion-resistant materials. Threaded connections used on subsea equipment covered by this part of ISO 13628 shall comply with the requirements of 5.1.2.1.7. 7.4 Other end connectors The use of other non-standard end connectors, such as misalignment connectors, non-ISO flanges, ball joints, articulated jumper assemblies or instrument/monitor flanges is allowable in subsea completion equipment if these connectors have been designed, documented and tested in accordance wilh the requirements established in Clause 5, Materials for OECs shall meet the requirements of 5.2 and 5.3. If the connector's primary seals are not metal-to- metal, redundant seals shall be provided. OECs used on subsea completion equipment shall have seal surfaces that engage metal-to-metal seals and shail be inlaid with a corrasion-resistant material that is compatible with well fluids, seawater, etc. Overlays are not required if the base material is a corrosion-resistant material For forged meterial used for pressure-containing and high-load-bearing pars, forging practices, heat treatment and test coupon (QTC or prolongation) requirements should meet those of API RP 6HT. In addition, the test ‘coupon shall accompany the material it qualifies through all thermal processing, excluding stress relief.