Scribd
Upload
95 views

Pallet Racking Assembly Instructions: Parts List Safety Information

This document provides instructions for assembling pallet racking. It lists the necessary parts and safety equipment. The 8 steps describe how to: 1) Measure and mark floor points for uprights; 2) Secure the first upright and lock in the lowest shelf beam; 3) Add additional uprights and beams to form bays; 4) Ensure uprights are level, beams are horizontal, and bays are square; 5) Fit remaining shelf beams; 6) Secure the racking to the floor with dynabolts; and 7) Attach a load rating sign. Safety is emphasized, and installing qualified personnel is recommended for commercial settings.

Uploaded by

Uni Tools
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
95 views

Pallet Racking Assembly Instructions: Parts List Safety Information

This document provides instructions for assembling pallet racking. It lists the necessary parts and safety equipment. The 8 steps describe how to: 1) Measure and mark floor points for uprights; 2) Secure the first upright and lock in the lowest shelf beam; 3) Add additional uprights and beams to form bays; 4) Ensure uprights are level, beams are horizontal, and bays are square; 5) Fit remaining shelf beams; 6) Secure the racking to the floor with dynabolts; and 7) Attach a load rating sign. Safety is emphasized, and installing qualified personnel is recommended for commercial settings.

Uploaded by

Uni Tools
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Pallet Racking, Shelving & Warehouse Solutions

PALLET RACKING ASSEMBLY INSTRUCTIONS


Important: Please note in some states Pallet Racking must be installed by a qualified person.

Parts List Safety Information


• Two people are required for safe assembly
Starter Units Qty
• Install shelving on a level and secure surface. Avoid soft surfaces
Upright Frame (Supplied Assembled) 2
like asphalt or tarmac.
Shelf Beams 8
• We recommend the use of floors fixings in commercial installations
Beam Locking Pins 16 • For maximum load per shelf please refer to your invoice
Dynabolts 8 • Never climb on shelving

Tools Required
Extension Units Qty
Upright Frame (Supplied Assembled) 1 • Impact drill, and appropriate drill bits • String line
Shelf Beams 8 • Rattle gun • Measuring
• 2 x 16 and 17mm open end spanners • Rotary impact drill
Beam Locking Pins 16
• 2 x 16mm impact sockets • Dust extractor vacuum
Dynabolts 8
• 2 x 8mm hex head • Extension leads
Important: Please contact your Unirack if any parts are missing • Full spanner and screwdriver sets • Level
or damaged before assembly. • Chalk line

STEP 1 STEP 2

Measure an even distance from two points on the wall Stand an upright by having one person secure the base or up
and mark the floor. Run a chalk line between the marks against wall and lock a beam in at the lowest point.
and flick the line.
Note: As a pallet will extend out the back of the racking a minimum of Note: Reason for placing beam at the lowest point is so the other end of the
300mm from the wall is recommended. beam is on the ground making it safe while getting the other upright.

STEP 3 STEP 4

Stand the next upright and lock it into place by securing Add the other lower beam to the other side of the upright
it to the beam again at the lowest point. therefore ending up with two uprights and two beams.

www.unirack.com.au 1300 864 725


STEP 5

Add another two beams to the right of the upright again on the lowest level. Then safely stand another upright and attach
to the beams, as per Step 3 & 4. This can be continued until the run is complete.

STEP 6

TOP VIEW

Then, once the bay and all the additional bays are in place ensure all the uprights are on the chalk line. Then check that the
uprights are level vertically and the beams are level horizontally. Also check the bay is square by ensuring the lengths of
the diagonals are identical.

STEP 7

Then fit all the upper beams at their desired height and finally raise or remove the lowest beam. Ensure that the safety clips
are fitted as you go.

STEP 8

SAFE WORKING LOADS

Kg Kg

UNEVEN-POINT LOAD
REFER SUPPLIER

Kg

Kg
TOTAL BAY LOAD

Then drill a hole using the impact drill and secure the racking to the ground using two Dynabolts per upright. Finally, place
the Load rating sign on the upright at the end of the row.

www.unirack.com.au 1300 864 725

You might also like