NNH4-65C-R6-V2

12-port sector antenna, 4x 703–894 and 8x 1695–2200 MHz, 65°

HPBW, 6x RET.
Features a downtilt range of 0-10° to provide for improved interference performance
Features broadband Low Band (698-896 MHz) and High Band (1695-2360 MHz) arrays for
4T4R (4X MIMO) capability for Band 14, AWS, PCS and WCS applications.
Independent tilt for all arrays.
Array configuration provides capability for 4T4R (4x MIMO) on Low band and Dual 4T4R
(4x MIMO) on High band
Optimized SPR performance across all operating bands
Excellent wind loading characteristics

General Specifications
Antenna Type Sector

Band Multiband

Effective Projective Area (EPA), frontal 0.9 m²   |   9.688 ft²

Effective Projective Area (EPA), lateral 0.31 m²   |   3.337 ft²

Grounding Type RF connector inner conductor and body grounded to reflector and
mounting bracket

Performance Note Outdoor usage    |   Wind loading figures are validated by wind tunnel
measurements described in white paper WP-112534-EN

RF Connector Interface 4.3-10 Female

RF Connector Location Bottom

RF Connector Quantity, high band 8

RF Connector Quantity, low band 4

RF Connector Quantity, total 12

Remote Electrical Tilt (RET) Information, General

RET Hardware CommRET v2

RET Interface 8-pin DIN Female    |   8-pin DIN Male

RET Interface, quantity 1 female    |   1 male

Dimensions
Width 498 mm   |   19.606 in

Length 2438 mm   |   95.984 in

Depth 197 mm   |   7.756 in

Page 1 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: January 17, 2020
NNH4-65C-R6-V2
Array Layout

Port Configuration

Page 2 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: January 17, 2020
NNH4-65C-R6-V2

Electrical Specifications
Operating Frequency Band 1695 – 2200 MHz    |   703 – 894 MHz

Total Input Power, maximum 900 W @ 50 °C

Remote Electrical Tilt (RET) Information, Electrical

Protocol 3GPP/AISG 2.0 (Single RET)

Power Consumption, idle state, maximum 1W

Power Consumption, normal conditions, maximum 8W

Input Voltage 10–30 Vdc

Internal RET High band (4)    |   Low band (2)

Electrical Specifications
Page 3 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: January 17, 2020
NNH4-65C-R6-V2
Frequency Band, MHz 703–803 824–894 1695–1880 1850–1990 1920–2200
Gain, dBi 15.8 16 17 17.5 17.8
Beamwidth, Horizontal, 75 73 58 59 61
degrees
Beamwidth, Vertical, degrees 9.7 8.7 7.9 7.4 7
Beam Tilt, degrees 2–12 2–12 2–12 2–12 2–12
USLS (First Lobe), dB 19 19 17 18 19
Front-to-Back Ratio at 180°, 32 33 39 42 39
dB
Isolation, Cross Polarization, 25 25 25 25 25
dB
Isolation, Inter-band, dB 25 25 25 25 25
VSWR | Return loss, dB 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0 1.5 | 14.0

PIM, 3rd Order, 2 x 20 W, dBc -150 -150 -150 -150 -150

Input Power per Port at 50° 300 300 250 250 250
C, maximum, watts

Electrical Specifications, BASTA

Frequency Band, MHz 703–803 824–894 1695–1880 1850–1990 1920–2200
Gain by all Beam Tilts, 15.3 15.8 16.5 17.1 17.3
average, dBi
Gain by all Beam Tilts ±0.7 ±0.4 ±0.8 ±0.6 ±0.6
Tolerance, dB
Gain by Beam Tilt, average, 2 ° | 15.2 12 ° | 15.7 2 ° | 16.6 2 ° | 17.1 2 ° | 17.1
dBi 7 ° | 15.3 2 ° | 15.8 7 ° | 16.8 7 ° | 17.4 7 ° | 17.6
12 ° | 15.2 7 ° | 15.9 12 ° | 16.2 12 ° | 16.7 12 ° | 16.9

Beamwidth, Horizontal ±2.5 ±2.1 ±4.8 ±2.4 ±3.4

Tolerance, degrees
Beamwidth, Vertical ±0.8 ±0.5 ±0.4 ±0.3 ±0.6
Tolerance, degrees
USLS, beampeak to 20° 16 16 14 15 16
above beampeak, dB
Front-to-Back Total Power at 23 22 31 33 29
180° ± 30°, dB
CPR at Boresight, dB 22 24 20 21 21
CPR at Sector, dB 9 6 9 9 7

Material Specifications
Radiator Material Low loss circuit board

Radome Material Fiberglass, UV resistant

Reflector Material Aluminum

Page 4 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: January 17, 2020
NNH4-65C-R6-V2
Mechanical Specifications
Wind Loading at Velocity, frontal 214.5 lbf @ 150 km/h    |   954.0 N @ 150 km/h

Wind Loading at Velocity, lateral 331.0 N @ 150 km/h    |   74.4 lbf @ 150 km/h

Wind Loading at Velocity, maximum 1,235.0 N @ 150 km/h    |   277.6 lbf @ 150 km/h

Wind Speed, maximum 241 km/h   |   149.75 mph

Packaging and Weights

Width, packed 608 mm   |   23.937 in

Depth, packed 352 mm   |   13.858 in

Length, packed 2620 mm   |   103.15 in

Net Weight, without mounting kit 46.8 kg   |   103.176 lb

Weight, gross 68.3 kg   |   150.576 lb

Regulatory Compliance/Certifications
Agency Classification
CHINA-ROHS Below maximum concentration value
ISO 9001:2015 Designed, manufactured and/or distributed under this quality management system
REACH-SVHC Compliant as per SVHC revision on www.commscope.com/ProductCompliance
ROHS Compliant

Included Products
BSAMNT-3 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top
bracket set and one bottom bracket set.
BSAMNT-M — Middle Downtilt Mounting Kit for Long Antennas for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one
scissor bracket set.

* Footnotes
Performance Note Severe environmental conditions may degrade optimum performance

Page 5 of 5

©2020 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks,
respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the
most current information. Revised: January 17, 2020