HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 2 OF 77

CONTENT

1 SCOPE ................................................................................................................................ 3

2 CODES, REGULATIONS, STANDARDS............................................................................ 3

3 GENERAL ........................................................................................................................... 5

4 PIPE.................................................................................................................................... 6

5 VALVES............................................................................................................................... 7

6 FLANGES............................................................................................................................ 8

7 FITTINGS............................................................................................................................. 9

8 BOLTING ............................................................................................................................. 9

9 GASKETS.......................................................................................................................... 10

10 NON METALLIC MATERIAL .......................................................................................... 10

11 SOUR SERVICE PIPING................................................................................................. 10

12 PIPING CLASSIFICATIONS AND MATERIAL SPECIFICATIONS................................ 11

APPENDICES

APPENDIX – A PIPING CLASSES SPECIFICATIONS

APPENDIX – B PIPING MATERIAL SPECIFICATIONS

APPENDIX – C BRANCH CONNECTIONS

 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 3 OF 77

1 SCOPE
This specification governs the selection and limitations of piping and piping system
components which belongs to the scope of ASME B31.3, ASME B31.4 and ASME B31.8.
This section should be read in conjunction with associated specifications of this project and
most stringent shall be followed when conflicts.

2 CODES, REGULATIONS, STANDARDS

2.1 Vendor shall meet or exceed the requirements of the latest edition or the equivalent ones
of the following codes, regulations and standards, except as superseded herein. In cases
where more than one code, regulation or standard apply to the same condition, the most
stringent shall be followed. In the event of a conflict between this specification and other
specifications or correspondence, the OWNER shall be consulted and a ruling, in writing,
shall be obtained before any work is started.
ASME Standards
ASME B1.1 Unified inch screw threads
ASME B16.5 Pipe Flanges and Flanged Fittings: NPS 1/2 through NPS 24
ASME B16.9 Factory-Made Wrought Butt-welding Fittings
ASME B16.10 Face-to-face and End-to-end dimensions of valves
ASME B16.11 Forged Fittings, Socket-Welding and Threaded
ASME B16.14 Ferrous pipe plugs, bushings, and locknuts with pipe threads
ASME B16.20 Metallic Gaskets for Pipe Flanges: Ring-Joint, Spiral-Wound, and
Jacketed
ASME B16.21 Non-metallic Flat Gaskets for Pipe Flanges
ASME B16.25 Butt-welding Ends
ASME B16.34 Valves Flanged, Threaded and Welding End
ASME B16.47 Large Diameter Steel Flanges: NPS 26 through NPS 60
ASME B16.48 Line Blanks
ASME B18.2.1 Square and hexagonal bolts and screws
ASME B18.2.2 Square and hexagonal nuts
ASME B31.3 Process Piping
ASME B31.4 Pipeline Transportation Systems for Liquid Hydrocarbons and
Other Liquids
ASME B31.8 Gas Transmission and Distribution Piping Systems
ASME B36.10M Welded and Seamless Wrought Steel Pipe
ASME B36.19M Stainless Steel Pipe
ASME B1.20.2M Pipe Threads, 60 deg. General Purpose
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 4 OF 77

API Standards
API STD 5L Specification for Line Pipe
API STD 600 Steel Gate Valves - Flanged and Butt-welding ends, Bolted
Bonnets
API STD 602 Compact Steel Gate Valves – Flanged, Threaded, Welded and
Extended-Body Ends
API STD 607 Fire test for Soft-Seated quarter-turn valves
API STD 609 Butterfly valves-double flanged, lug-and wafer-type
API SPEC 6FA Specification for Fire Testing of Valves
API SPEC 6D Specification for pipe line valves (Gate, Plug, Ball and Check
valves)

MSS-SP Standards
MSS-SP-43 Wrought Stainless Steel Butt-Welding Fittings
MSS-SP-25 Standard Marking System for Valves, Fittings, Flanges, Unions
MSS-SP-75 Specification for High Test Wrought Butt-welding Fittings
MSS-SP-95 Swage(d) Nipples and Bull Plugs

NACE Standards
NACE-RP-0169 Control of External Corrosion on Underground or Submerged
Metallic Piping System
NACE-PR-0286 Electrical Isolation of Cathodic Protection
NACE MR0175 Sulfide stress cracking resistant metallic materials for Oil-field
equipment

ISO Standards

ISO 15590-1 Petroleum and natural gas industries—Induction bends

ISO 15761 Steel gate, globe and check valves for sizes DN 100 and smaller,
for the petroleum and natural gas industries

BS Standards
BS 1873 Specification for Steel globe and globe stop and check valves
(flanged and butt-welding ends) for the petroleum, petrochemical
and allied industries
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 5 OF 77

Note: This list covers the majority of references, but it is not exhaustive.
2.2 The following General Specifications shall be used in conjunction with this specification
where applicable:
HFY-PIP-SP-00001 Specification for Piping Design and Layout
HFY-PIP-SP-00002 Specification for Pressure Testing of Steel Piping Systems
HFY-PIP-SP-00003 Specification for Piping Fabrication
HFY-PIP-SP-00004 Specification for Piping and Pipeline Welding in Sour Service
HFY-PIP-SP-00006 Specification for Valves
HFY-PIP-SP-00007 Specification for Construction and Installation of Piping
HFY-PIP-SP-00008 Specification for Insulation
HFY-PIP-SP-00009 Specification for BNS Seamless Piping Material
HFY-PIP-SP-00010 Specification for BNS Fittings
HFY-PIP-SP-00011 Specification for BNS SAWL Piping Material
HFY-PIP-SP-00013 Specification for Piping and Pipeline Welding in non- Sour Service
HFY-PIP-SP-00014 Specification for Sour Service Forged Material
HFY-PPL-SP-00003 Specification for Transportation and Handle of Steel Pipe

2.3 Some requirements in this specification may be modified by specific requirements in the
Purchase Specification. In case of conflict, the specific requirements supersede this
specification.
2.4 Any deviation from this specification must be approved, in writing, by OWNER. Such
written approval must be obtained prior to the commencement of any work which would
constitute such a deviation.

3 GENERAL
3.1 All pressures given in this Specification are gauge pressure unless specially noted.
3.2 Except under special conditions of severity, hazard, etc., the materials used shall be in
accordance with the Piping Materials Specification which is based on the design pressure
and temperature and on the type of service. The materials used under special conditions of
severity and hazard must be suitable for the particular service conditions involved.
3.3 The corrosion allowance specified for the classes shall be considered in the calculation of
the wall thickness.
3.4 In no case it shall be reduced to obtain a thinner commercially available pipe thickness.
3.5 The abbreviated material description in the classes gives brief information to the piping
designer. For the supply of the material, detailed technical requirements shall be included the
purchasing requisitions.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 6 OF 77

3.6 All material used shall be selected in accordance with code requirements and industry
standards for good workmanship.
3.7 Pipe materials shall be selected as follows, whenever temperature is the governing factor.
Material Temperature Range
Carbon Steel -20℃ to 425℃
Type 316L stainless steel -196℃ to 450℃
Low alloys (carbon-moly and chrome alloys) -40℃ to 450℃
Other types of materials or alloys shall be used where corrosive conditions are the governing
factor. NACE MR 01-75/ISO 15156 shall be used for selecting and treating of materials for
piping in sour services.
3.8 The use of any materials containing asbestos is prohibited for gasket and valve packing.
3.9 All piping materials shall meet the impact requirements of ASME B31.3, ASME B31.4 and
ASME B31.8.
3.10 Marking for pipe and fittings shall be done as per relevant piping standard, and shall
include the following,
 The size
 The specification and grade of material
 The heat number
 The batch number
On ferrous material with a thickness under 5mm (austenitic steels under 10mm), marking
shall be applied by engraving or by stencilling. For stencil marking, a water insoluble ink shall
be used, that does not contain substances which could harmfully affect the material.
On ferrous material with a thickness 5mm & over (austenitic steels 10mm & over), marking
shall be applied by low stress hard die stamping. Low stress stamps shall have a round nose
with a radius of minimum 0.25mm.

4 PIPE
4.1 Pipe shall normally be as specified in the Specification for Piping Materials for the
applicable Piping Class Rating and Service.
4.2 Piping for service below -20℃ and above 454℃ shall be approved in writing by OWNER.
4.3 Material API 5L PSL2 BNS and X52NS is for sour service. For chemical injection service,
ASTM A 312-TP316L shall be used. Pipe material is API 5L PSL2 Gr.BN. For the other
service material selection, please refers to Appendix B.
4.4 Marking and Finish
Pipe shall be legibly marked in accordance with the applicable ASTM or ISO specification.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 7 OF 77

4.5 Pipe sizes 1¼",2½",3½",5",7",9",22",26",34",38”, 44” & 46” shall not be used. Line
connections to equipment with such connections sizes shall be made with suitable reducing
fittings.
4.6 Galvanized piping (1G0)
These piping from air header to different field instruments shall be installed with the following
considerations.
4.6.1 Threaded connections shall be done by the use of thread compound or P.T.F.E. (Teflon)
tape. P.T.F.E. tape shall not be used where temperatures exceed 230°C (450°F).
Wherever thread compound is used on screwed fittings it should be applied to the male
thread only.
4.6.2 All pipe ends shall be cut square, reamed of all burrs and cleared of all foreign material.
4.6.3 Cutting oil shall be used in cutting all threads on galvanized pipe.
4.7 Hardness of Pipe Material
The maximum hardness of pipe with welded seams anywhere in the weld, heat-affected zone,
or parent metal shall follow the requirements specified in latest edition of NACE MR
0175/ISO15156 or other applicable codes & standards and Section 2.1.
4.8 Schedules 5S shall not be used for stainless steels and schedule 80 shall be selected for
carbon steel as a minimum for pipes 1½” diameter and below.

5 VALVES
5.1 General

Valves shall be provided in accordance with this specification and HFY-PIP-SP-00006

Specification for Valves.
No valves of brass, cast iron, ductile iron, nodular iron, or semi-steel; nor valves containing
rubber, bronze or plastics shall be used unless specifically noted in the Specification for
Valves HFY-PIP-SP-00006.
Flanged valves shall be used in place of socket weld and screwed valves in 3/4” and 1 1/2”
sizes when mounted directly to flanged connection, vent, drain and level control connection.
Rating of valves must match nozzle connection.
Care shall be taken to maintain differential hardness between seats and ball/wedge/plug/disc
in nickel based alloys to prevent galling.
All valves shall be of fire-safe design. Ball valves shall be fire-safe tested in accordance with
BS 6755 part 2 or equal and shall have appropriate certification.
Gear operators shall be provided on valves as required in the HFY-PIP-SP-00006
Specification for Valves.
Valves shall be provided with a position indicator. Showing open position in the direction of
flow and close position perpendicular to the direction of flow. The shut and open terms in
English shall be permanently indicated in a visible location.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 8 OF 77

Stem protectors shall be provided for all outside screw and yoke (OS&Y) flanged valves.
Locking devices shall be supplied as per manufacturer’s standard.
Welded-end (butt welded) valves of any type (e.g., ball, gate, check, etc.) shall not be
allowed without prior, specific written approval of OWNER on a case by case basis. In this
project, the heating medium system piping valve shall be flanged-end. Detailed information
refers to HFY-PIP-SP-00006 Specification for Valves.
All valves, excluding check valves unless specified otherwise, shall be provided with hand
wheels, levers, wrenches or gear operators as required for the intended services, and shall
be capable of sealing with design pressure applied from either end of the valve. All ball,
check, gate and globe valves shall be field repairable. Balls, discs, flappers, seals and seats
shall be replaceable without requiring welding or cutting.
In the absence of a specified test procedure, API 598, ISO5208, BS 6755 or API 6D shall be
the basis for testing.
5.2 Valve Identification
Each valve in a facility shall be designated by a descriptive valve identification number
consisting of the following identifiers:
 Nominal Valve Size (inches NPS)
 Valve Type
 Piping Class Code
 Valve Style
 S (NACE TAGGED)
E.G. 10"-BA-1A1-1S, specifies:
10" -----Nominal valve size.
BA -----Valve Type (Ball Valve).
1A1 -----Piping Class Code (See APPENDIX A)
1 -----Valve style (See HFY-PIP-SP-00006 Specification for Valves)
S -----NACE Tagged.
Valve Type:
BA - Ball BT - Butterfly CK – Check GA - Gate GL - Globe PL-Plug

6 FLANGES
6.1 Flanges shall be provided in accordance with this specification for the applicable Piping
Class Rating and Service.
6.2 Flanges and flanged connections up to and including NPS 24” shall be in accordance
with ASME B 16.5 and flanges 26" & above shall be in accordance with ASME B16.47 series
"A" (formerly MSS SP 44) unless otherwise stated.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 9 OF 77

6.3 RF(less than 900#) and RJ (900# and above) are recommended for ease of fit up and
installation and removal of valves and equipment with OWNER approval. For Piping Class
1G0 (Galvanised), in place of socket welded & weld neck flanges, screwed (NPT) raised face
flanges shall be used.
6.4 Spectacle blind shall be in accordance with ASME B16.48 & shall be suitable for
installation between ASME B16.5 RF and RJ flanges.
6.5 Orifice flanges shall be supplied in pairs, complete with jackscrews for ease of removal.
Quantities on bills-of-material, material requisitions, etc., shall indicate sets, not individual
flanges.
6.6 All spec breaks (e.g. two different materials or different thicknesses) must be indicated at
flanges.
6.7 Slip-on flanges (flat face) are permitted only for where connection is necessary between
fibreglass flanges and steel flanges.
6.8 Flange Surface Finish shall be 125μin to 250 125μin according to ASME B16.5 for RF
and FF flange. For RJ flanges, the side wall surface finish of the gasket groove shall not
exceed 1.6μm(63μin) roughness.

7 FITTINGS
7.1 Fittings shall be provided in accordance with this specification for the applicable Piping
Class Rating and Service.
7.2 Fittings shall conform to ASTM A234, ASTM A105N, ASTM A694, and ASTM A182 &
ASTM A403, etc. as applicable.
7.3 For sour service, API 5L PSL2 Gr.BNS, X52NS, and ASME A350 LF2 are chosen as
material of fittings.
7.4 Branch Connections using welding tees or commercial integrally reinforced fittings such
as Weldolets, or Threadolets are equally acceptable, with the choice of the type of
connection based on the criteria provided by the Branch Connection Tables contained in
Appendix C.
7.5 Butt weld elbows shall be long radius type (radius = 1½ nominal pipe size).
7.6 Fittings shall be prepared for shipment in a manner that damage or atmospheric
corrosion of internal or external surfaces is avoided during storage and transport.
7.7 Fittings shall be marked in accordance with MSS SP-25.

8 BOLTING
8.1 Flange bolting shall be provided suitable for connecting ASME B16.5 /ASME B16.47
Series A flanges in accordance with this specification for the applicable Piping Class Rating
and Service.
8.2 Materials for use below -20℃ and above 425℃ shall be approved in writing by OWNER
unless otherwise specified in supplementary specifications.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 10 OF 77

8.3 Nuts shall be heavy hexagonal. All threading shall confirm to ASME B1.1.
8.4 Threads on stud bolts and nuts under or equal to 1” diameter shall be coarse thread
series(UNC threads). Larger diameter studs shall have Unified 8(8UN Threads) Class 2A
threads. Nuts shall have Class 2B threads.
8.5 Studs shall be threaded full length.

8.6 Bolt tensioning shall be considered for all bolts 1½” (38 mm) diameter and larger. In all
such cases the bolt length shall be increased by normal required length plus one bolt
diameter. In addition, for elevated temperatures, cyclic service and other critical joints,
controlled tensioning shall be considered.

9 GASKETS
9.1 Gaskets shall be provided in accordance with this specification for the applicable Piping
Class Rating and Service.
9.2 Gaskets shall be according to ASME B16.20/ASME B16.21 used for ASME B16.5/B16.47
Series A flanges connection. The end types of flanges are RF and RJ.
 For RJ flanged, gaskets shall be Oval Ring Type.
 Soft Iron Oval ring gaskets shall have maximum hardness limit up to 90BHN/
 Surface finish shall be according to ASME B16.20 para, 2.6.

10 NON METALLIC MATERIAL

For non metallic material used in this project, the related standards shall be followed.

11 SOUR SERVICE PIPING

11.1 General Requirement
All components shall comply with the requirements of NACE MR0175.
Where a difference in Codes, Standards exists, the more stringent requirement shall govern.
If no special definition, the maximum carbon equivalent (CE) of all components shall be less
than 0.43%.
If no special definition, the maximum hardness of all components at any position shall be not
higher than 200HB.
11.2 Piping
a) The pipe material used in sour service shall comply with the requirements of Specification
for API 5L PSL2 Gr. BNS Seamless Piping Material, Specification for API 5L PSL2 Gr. BNS
and Gr. X52NS SAWL Piping Material;
b) Threaded and socket welded piping shall not be used in sour service; such piping shall be
butt-welded and flanged.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 11 OF 77

11.2.1 Fitting & Flanges

The steel fittings and flanges used in sour service shall comply with the requirements of HFY-
PIP-SP-00010 Specification for BNS Fittings and HFY-PIP-SP-00014 Specification for Sour
Service Forged Material.
11.2.2 Bolting
a) ASTM A193 Grade B7M bolting materials and ASTM A194 Grade 2HM nuts material shall
be mating with carbon steel components.
b) Proper bolt tightening procedures shall be used to avoid cold working, or yielding of bolt
materials. Impact tightening is not permitted.

12 PIPING CLASSIFICATIONS AND MATERIAL SPECIFICATIONS

12.1 Line Identification:

BB” CC DDDDD EE F(F) G H I J

1 2 3 4 5 6 7 8 9
3” HC 10211 13 1 A 1 H E

1―― Pipe Size

Nominal sizes in inches.
2―― Product Service Codes

Abbreviation Fluid Abbreviation Fluid

AI Instrument Air HC Hydrocarbon Liquid
AS Starting Air HG Hydrocarbon Gas
AU Utility Air HM Heating Medium
CF AFFF Concentrate ME Methanol
CH Hypochlorite OH Hydraulic Oil
CI Chemical injection OL Lubricating Oil
CM Chemical Injection (Methanol) OS Seal Oil
CO Crude Oil PR Propane
DC Closed Drain SO Slop Oil
DO Open Drain VA Atmospheric Vent
DS Sanitary Drain VH High Pressure Flare
DT Glycol Drain VL Low Pressure Flare
FA Aviation Fuel VT Vessel Trim
FD Diesel Fuel, Gasoline WC Cooling Water
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 12 OF 77

Abbreviation Fluid Abbreviation Fluid

GB Blanket Gas WD Fresh Water (non Potable)
GE Exhaust Gas WF Fire Water
GF Fuel Gas WO Produced Water
GL Glycol WP Potable Water
GI Nitrogen Gas WS Sea Water
GC Carbon Dioxide WW Waste Water
SL Sludge WI Water Injection
FS Foam Solution LS Liquid Sulfur
PG Sour Gas SW Soften Water
AW Sour Water ST Steam
Mixture Liquid of Glycol and
LH CW Condensate Water
Hydrocarbon
BFW Boiler Feed Water DOW Deoxygenated Water

3―― The first four digits of the equipment digit number

Detailed numbering refers to Numbering system
4―― Sequence Number
The sequence number shall run consecutively from 01 before each equipment, preferably in
such a way that the main medium flow is followed. Parallel lines should be numbered
separately. Refer to Numbering system.
5―― Piping Pressure Rating
1 150 pounds rating (ASME codes)

3 300 pounds rating (ASME codes)

6 600 pounds rating (ASME codes)

9 900 pounds rating (ASME codes)

15 1500 pounds rating (ASME codes)

25 2500 pounds rating (ASME codes)

50 5000 pounds rating (API codes)

100 10000 pounds rating (API codes)

6―― Piping Material Classification

A Carbon Steel
B Low Temperature Carbon Steel
C Stainless Steel
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 13 OF 77

D Carbon Steel Sour Service

E Low Temperature Carbon Steel Sour Service
F Stainless Steel Sour Service
G Carbon Steel Galvanised Pipe
H Cunifer
J PVDF
K Carbon Steel with inner coating
L Super Duplex Stainless Steel (25% Cr)
M 6% Molybdenum
N Duplex Stainless Steel (22% Cr)
P Glass Fibre Reinforced Plastic
R Duplex Stainless Steel (22% Cr) Sour Service
S PVCU
T High Temperature Carbon Steel(Heating medium service)
U Steam Jacked Carbon Steel(Liquid Sulfur service)
Q Carbon Steel (for pipeline)
X Carbon Steel Sour Service(for pipeline)

7―― The sequence number indicates the material corrosion grade

0 Corrosion allowance is 0 mm
1 Corrosion allowance is 1 mm
2 Corrosion allowance is 2 mm
3 Corrosion allowance is 3 mm
4 Corrosion allowance is 4 mm

8―― Insulation class

A Acoustic Protection
C Frost Proofing
F Fire Protection
H Heat Conservation
P Personnel Protection
Z Cold Conservation

9――Tracing Class
S Steam Jacket Tracing
W Hot Water Tracing
E Electrical Heating Tracing
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 14 OF 77

12.2 Abbreviations Used (in alphabetical order)

ABBREVIATION NAME NOTE

AL Aluminum
ASME American National Standard Institute
API American Petroleum Institute
ASME American Society of Mechanical Engineers
ASTM American Society of Testing and Materials
ATM Atmosphere
BB Bolted Bonnet
BBE Beveled both Ends
BC Bolted Cover
BE Beveled End
BLE Beveled Large End
BOE Beveled One End
Br Bronze
BRZG Capillary Brazing End
BSE Beveled Small End
BW Butt Welding
CA Corrosion Allowance
CAS Cast Alloy Steel
CCS Cast Carbon Steel
CI Cast Iron
CONC Concentric
Cr Chromium
CS Carbon Steel
CSA Canadian Standards Association
CuNi Copper-Nickel
CWP Cold Working Pressure
D Diameter
ECC Eccentric
EFW Electric Fusion Welded
EQ Equal
ERW Electric Resistance Welded
F6 Stainless Steel, 13% Cr
FAS Forged Alloy Steel
FCS Forged Carbon Steel
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 15 OF 77

ABBREVIATION NAME NOTE

FF Flat Face
FM Female Face
GALV Galvanize
Gr Grade
HEX Hexagonal
HT Heat Tracing
IH Hot Insulation
IP Personnel Protection Insulation
LJ Lap Joint
LR Long Radius
M Male Face
Manuf Manufacturer
Max Maximum
MI Malleable Cast iron
Mo Molybdenum
MPCS Micro-porous Calcium Silicate
MSS Manufacturer Standardization Society
NCS Normalized Carbon Steel
Ni Nickel
NPT Threading as per ASME B1.20.1
OD Outside Diameter
PBE Plain both Ends
PE Plain End
PLE Plain Large End
PO Polyurethane
POE Plain One End
PSE Plain Small End
PT Polyethylene Type
PVC Polyvinyl Chloride
R Radius
RED Reducing
RF Raised Face
RJ Ring Joint Face
SAW Submerged Arc Welding
SB Screwed Bonnet
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 16 OF 77

ABBREVIATION NAME NOTE

Sch Schedule
SMLS Seamless
SS Stainless Steel
STD Standard
SW Socket Welding
TBE Threaded both Ends
TE Threaded End
THK Thickness
TLE Threaded Large End
TLPR Two layer Polyolefin Resin
TOE Threaded one End
TSE Threaded Small End
WB Welded Bonnet
WN Welded Neck

Appendix A and B provide details for the selection and limitations of piping materials for each
piping class rating and service. For branching table refer to Appendix C.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 17 OF 77

APPENDIX A

PIPING CLASSES SPECIFICATIONS

 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 18 OF 77

APPENDIX A PIPING CLASSES SPECIFICATIONS

C.A. Service Limit

Class Service Symbol Rating Material (mm) P T
MPa ℃
Exhaust Gas GE
Utility Air AU
Propane PR
Glycol Drain DT
On Spec Crude Oil CO
Hydraulic Oil OH
Lubricating Oil OL
Seal Oil OS
Fuel Gas GF
Hydrocarbon Gas HG
1.96 -20/38
1A1 Diesel Fuel, Gasoline FD 150 # API 5L. PSL2 Gr.BN 1 1.58 148.9
Blanket Gas GB
Nitrogen Gas GI
Glycol GL
Atmospheric Vent VA
Soften Water SW
Steam ST
Condensate Water CW
Boiler Feed Water BFW
Deoxygenated Water DOW

Open Drain DO

Hydrocarbon Liquid
HC
(non-sour)
Open Drain(Oil area) DO
Fire Water WF
1.96 -20/38
1A3 Fresh Water WD 150 # API 5L. PSL2 Gr.BN 3
1.58 148.9
Cooling Water WC
Foam Solution FS

Potable Water WP
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 19 OF 77

APPENDIX A PIPING CLASSES SPECIFICATIONS

C.A. Service Limit

Class Service Symbol Rating Material (mm) P T
MPa ℃
Open Drain(Water
DO
Area)
Produced Water WO
1.96 -20/38
1A4 Slop Oil SO 150 # API 5L PSL2 Gr.BN 4
1.77 100
Water Injection (LP) WI

Waste Water WW

1.5 -20/38
1C0 Chemical injection CI 150 # S.S.316L 0
1.3 100
Crude Oil (Sour) CO
Closed Drain DC
Sour Gas/Sour Water PG/AW
Hydrocarbon Gas HG
1.96 -20/38
Atmospheric Vent VA API 5L PSL2 Gr.BNS
1D3 150 # 3 1.58 148.9
（Sour Service）
High Pressure Flare VH 0.34 200
Low Pressure Flare VL
Hydrocarbon Liquid
HC
(sour)
Off-spec Oil CO
API 5L PSL2 Gr.BN 1.96 -20/38
1G0 Instrument Air AI 150 # 0
+GALV 1.77 100
1.96 -20/38
3T1 Heating Medium HM 300 # API 5L PSL2 Gr.BN 1
1.2 260
1.96 -20/38
1U1
Liquid Sulfur LS 150 # API 5L PSL2 Gr.BN 1 1.58 148.9
(HOLD)
1.38 200
Fuel Gas GF
Chemical injection CI
Glycol GL
Mixture Liquid of 4.1 -20/38
3A1 300 # API 5L PSL2 Gr.BN 1
Glycol and LH 3.55 93
Hydrocarbon
Hydrocarbon Liquid HC
Hydrocarbon Gas HG
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 20 OF 77

APPENDIX A PIPING CLASSES SPECIFICATIONS

C.A. Service Limit

Class Service Symbol Rating Material (mm) P T
MPa ℃
4.1 -20/38
3C0 Chemical injection CI 300 # S.S.316L 0
3.4 100
8.2 -20/38
6C0 Chemical injection CI 600 # S.S.316L 0
6.9 100
API 5L PSL2 Gr.BNS
3X3 Hydrocarbon Gas /
HG 4.7 -20/38
(B31.8) Export 300 # API 5L PSL2 3
CO 4.7 90
(B31.4) Cruid Oil Gr.X52NS
（Sour Service）
Crude Oil CO
Process Sour Gas PG
Hydrocarbon Gas HG
API 5L PSL2 Gr.BNS 4.7 -20/38
3D3 Atmospheric Vent VA 300 # 3
（Sour Service） 4.7 90
Hydrocarbon Liquid HC
High Pressure Flare VH
Low Pressure Flare VL

Crude Oil CO
9.0 0/38
6A1 600 # API 5L PSL2 Gr.BN 1
9.0 148.9
Chemical injection CI

API 5L PSL2 Gr.BNS 9.0 0/38

6D3 Crude Oil CO 600 # 3
(Sour Service) 9.0 148.9
6Q0
9.0 0/38
(B31.4) Crude Oil Export CO 600 # API 5L PSL2 Gr.X60 0
9.0 148.9
(HOLD)
15Q4
25.5 0/38
(B31.4) Water Injection WI 1500# API 5L PSL2 Gr. X60 4
22.54 148.9
(HOLD)
15A4 25.5 0/38
Water Injection (CPF) WI 1500# API 5L PSL2 Gr. BN 4
(HOLD) 22.54 148.9
25D3 42.5
Crude Oil CO 2500# API 6A (HOLD) 3 HOLD
(HOLD) 37.5
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 21 OF 77

APPENDIX B

PIPING MATERIAL SPECIFICATION

 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 22 OF 77

1A1 Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 150 # PWHT NONE Piping Material C.S.

Allowable 1.96MPa @ -20/38℃

Pressure 1.58 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch. /Thk. Description
BA-1A11 (Floating Ball,
800# SW
Full Bore)
1/2” 1 1/2”
BA-1A12 (Floating Ball,
150# Flanged,RF
Full Bore) (Note 1)
BA-1A13 (Floating Ball,
2” 4” 150# Flanged,RF
Full Bore)
Ball Valve BA-1A14 (Trunnion
6” 24” 150# Flanged,RF Mounted, Full Bore/W
Gear Operator
BA-1A17 (Floating Ball,
3” 4” 150# Flanged,RF
Reduced Bore)
BA-1A18(Trunnion
6” 24” 150# Flanged,RF Mounted, Reduced Bore
/W Gear Operator
800# SW GA-1A11 (Wedge Gate)
1/2” 1 1/2”
150# Flanged,RF GA-1A12 (Wedge Gate)
2” 8” 150# Flanged,RF GA-1A13 (Wedge Gate)
Gate Valve 2” 8” 150# Flanged,RF GA-1A14 (Flat Gate) (Note1)
GA-1A15 (Wedge Gate &
10” 24” 150# Flanged,RF
/W Gear Operator)
GA-1A16 ((Flat Gate & /W
10” 24” 150# Flanged,RF
Gear Operator)
1/2” 1 1/2” 150# Flanged,RF GL-1A11 (Spherical Disc)
GL-1A12 (Spherical Disc
2” 6” 150# Flanged,RF
Globe Valve & Renewable Seat) (Note1)
GL-1A13 (Spherical Disc
8” 16” 150# Flanged,RF & Renewable Seat With
Gear Operator)
1/2” 1 1/2” 150# Flanged,RF CK-1A11 (Lift)
Check
(Note1)
Valve 2” 24” 150# Flanged,RF CK-1A12 (Wafer)
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 23 OF 77

1A1 Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 150 # PWHT NONE Piping Material C.S.

Allowable 1.96MPa @ -20/38℃

Pressure 1.58 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch. /Thk. Description
BT-1A11 (Three-
2” 6” 150# Flanged,RF
Eccentricity)
Butterfly
BT-1A12 (Three- (Note1)
Valve
8” 24” 150# Flanged,RF Eccentricity With Gear
Operator)
1/2” 1 1/2” SCH80 BE Seamless, Steel Pipe
2” 2” 3.91mm BE Seamless, Steel Pipe
3” 3” 4.37mm BE Seamless, Steel Pipe
4” 4” 4.78mm BE Seamless, Steel Pipe
API 5L
6” 6” 5.56mm BE Seamless, Steel Pipe PSL2.GR.BN,
Pipe 8” 8” 6.35mm BE Seamless, Steel Pipe ASME B36.10M
10” 10” 7.09mm BE Seamless, Steel Pipe
12” 12” 8.38mm BE Seamless, Steel Pipe
14” 16” 8.74mm BE Seamless, Steel Pipe
18” 18” 9.53mm BE Seamless, Steel Pipe
20” 24” 8.74mm BE SAWL, Steel Pipe

API 5L
Seamless, Steel Pipe
Nipple 1/2” 1 1/2” SCH160 - PSL2.GR.BN,
(80mm Long)
ASME B36.10M

Elbow, Tee, Coupling, ASTM A105N,

Fittings 1/2” 1 1/2” 3000# SW
Cap, Union ASME B16.11

Coupling, Cap,
ASTM A105N,
Union,
1/2” 1 1/2” 3000# NPT ASME B16.11 &
Threadolets
MSS SP-97
(Note 4)
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 24 OF 77

1A1 Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 150 # PWHT NONE Piping Material C.S.

Allowable 1.96MPa @ -20/38℃

Pressure 1.58 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch. /Thk. Description

ASTM A105N,
1/2” 1 1/2” 3000# SW Sockolets
MSS SP 97

2” 2” SCH40 BW
3” 4” SCH30 BW
6” 6” 5.56mm BW
ASTM A234
8” 8” SCH20 BW Gr.WPB
Elbow (LR) ,Tee, Seamless
10” 12” SCH30 BW
Reducer,Cap
ASME B16.9,
14” 14” 8.74mm BW
16” 16” 8.74mm BW
Fittings
18” 18” 9.53mm BW
20” 24” SCH20 BW
1/2” 1 1/2” SCH80 BW
2” 2” SCH40 BW
ASTM A105N
3” 4” SCH30 BW Weldolets
MSS SP 97
6” 6” 5.56mm BW
8” 8” SCH20 BW
1/2” 24” 150# Flanged,RF Welding Neck(Note2)
ASTM A105N,
2” 24” 300# Flanged,RF Welding Neck(Note 2,3)
ASME B16.5
1/2” 24” 150# Flanged,RF Blind
Flanges 1/2” 12” 150# - Spectacle Blank ASTM A105N,
14” 24” 150# - Blinds and Spacer ASME B16.48
Orifice Flange Set, 0.5” ASTM A105N,
2” 24” 300# Flanged,RF
socketweld taps (Note 2) ASME B16.36

Full Length, /W Two HVY Stud Bolts, Alloy

Studs/ Steel, ASTM
1/2” 24” 150# N/A Hexagonal Nuts To
Nuts ASME B 18.2.1/18.2.2 A193-B7 /194-2H,
Hot Dip
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 25 OF 77

1A1 Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 150 # PWHT NONE Piping Material C.S.

Allowable 1.96MPa @ -20/38℃

Pressure 1.58 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch. /Thk. Description
Galvanized ASTM
A153
2” 24” 300# N/A

1/2” 24” 150# N/A

SS 316L/FG,
Spirally Wound /W SS
Gasket 4.5mm Thk,
Inner & CS Outer Rings
ASME B 16.20
2” 24” 300# N/A

Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
3. To be used only to match Class 300 flange connections at control valves and special equipment.
4. For Utility Air service.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 26 OF 77

1A3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 150 # PWHT NONE Piping Material C.S.

Allowable 1.96 MPa @ -20/38℃

Pressure 1.58 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
BA-1A31 (Floating Ball,
800# SW
Full Bore)
1/2” 1 1/2”
BA-1A32 (Floating Ball,
150# Flanged,RF
Full Bore)
BA-1A33 (Floating Ball,
2” 4” 150# Flanged,RF
Full Bore)
Ball BA-1A34 (Trunnion (Note 1)
Valve 6” 24” 150# Flanged,RF Mounted, Full Bore/W
Gear Operator
BA-1A37 (Floating Ball,
3” 4” 150# Flanged,RF
Reduced Bore)
BA-1A38 (Trunnion
6” 24” 150# Flanged,RF Mounted, Reduced
Bore /W Gear Operator
800# SW GA-1A31 (Wedge Gate)
1/2” 1 1/2”
150# Flanged,RF GA-1A32 (Wedge Gate)
2” 8” 150# Flanged,RF GA-1A33 (Wedge Gate)
Gate 2” 8” 150# Flanged,RF GA-1A34 (Flat Gate) (Note1)
Valve
GA-1A35 (Wedge Gate
10” 24” 150# Flanged,RF
& /W Gear Operator)
GA-1A36 ((Flat Gate &
10” 24” 150# Flanged,RF
/W Gear Operator)

GL-1A31 (Spherical
1/2” 1 1/2” 150# Flanged,RF
Disc)

GL-1A32 (Spherical
Globe 2” 6” 150# Flanged,RF Disc & Renewable (Note 1)
Valve Seat)

GL-1A33 (Spherical
8” 16” 150# Flanged,RF Disc & Renewable Seat
With Gear Operator)
Check 1/2” 1 1/2” 150# Flanged,RF CK-1A31 (Lift) (Note1)
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 27 OF 77

1A3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 150 # PWHT NONE Piping Material C.S.

Allowable 1.96 MPa @ -20/38℃

Pressure 1.58 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
Valve 2” 24” 150# Flanged,RF CK-1A32 (Wafer)
BT-1A31 (Three-
2” 6” 150# Flanged,RF
Eccentricity)
Butterfly
BT-1A32 (Three- (Note 1)
Valve
8” 24” 150# Flanged,RF Eccentricity With Gear
Operator)
1/2” 1 1/2” SCH80 BE Seamless, Steel Pipe
2” 2” 3.91mm BE Seamless, Steel Pipe
3” 3” 4.37mm BE Seamless, Steel Pipe
4” 4” 4.78mm BE Seamless, Steel Pipe
5” 5” 6.55mm BE Seamless, Steel Pipe
6” 6” 5.56mm BE Seamless, Steel Pipe
API 5L PSL2.GR.BN,
Pipe 8” 8” 6.35mm BE Seamless, Steel Pipe
ASME B36.10M
10” 10” 7.09mm BE Seamless, Steel Pipe
12” 12” 8.38mm BE Seamless, Steel Pipe
14” 14” 9.53mm BE Seamless, Steel Pipe
16” 16” 9.53mm BE Seamless, Steel Pipe
18” 18” 9.53mm BE Seamless, Steel Pipe
20” 24” 8.74mm BE SAWL, Steel Pipe
Seamless, Steel Pipe API 5L PSL2.GR.BN,
Nipple 1/2” 1 1/2” SCH160 -
(80mm Long) ASME B36.10M
C. Swage ASTM A105N, MSS
2”x2-1/2” XS BEXNPT Seamless, BSE X TLE
Nipple SP-95

Elbow, Tee, Coupling, ASTM A105N,

Fittings 1/2” 1 1/2” 3000# SW
Cap, Union ASME B16.11

Coupling, Cap, ASTM A105N,

1/2” 1 1/2” 3000# NPT Union, ASME B16.11 & MSS
Threadolets SP-97
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 28 OF 77

1A3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 150 # PWHT NONE Piping Material C.S.

Allowable 1.96 MPa @ -20/38℃

Pressure 1.58 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description

ASTM A105N,
1/2” 1 1/2” 3000# SW Sockolets
MSS SP 97

2” 2” SCH40 BW
3” 4” SCH30 BW
5” 5” SCH40 BW
6” 6” 5.56mm BW ASTM A234 Gr.WPB,
Elbow (LR) ,Tee, Seamless
8” 8” SCH20 BW Reducer
ASME B16.9
10” 16” SCH30 BW
Fittings 18” 18” 9.53mm BW
20” 24” SCH20 BW
1/2” 1 1/2” SCH80 BW
2” 2” SCH40 BW
ASTM A105N,
3” 4” SCH30 BW Weldolets
MSS SP 97
6” 6” 5.56mm BW
8” 8” SCH20 BW
1/2” 24” 150# Flanged,RF Welding Neck (Note2)
Welding Neck (Note2, ASTM A105N,
2” 24” 300# Flanged,RF
3) ASME B16.5
1/2” 24” 150# Flanged,RF Blind
Flanges 1/2” 12” 150# - Spectacle Blank ASTM A105N,
14” 24” 150# - Blinds and Spacer ASME B16.48

Orifice Flange Set, ASTM A105N,

2” 24” 300# Flanged,RF 0.5”socketweld
taps(Note 2) ASME B16.36

1/2” 24” 150# N/A Stud Bolts, Alloy Steel,

Studs/ Full Length, /W Two
ASTM A193-B7 /194-
HVY Hexagonal Nuts
Nuts 2H, Hot Dip Galvanized
2” 24” 300# N/A ASME B 18.2.1/18.2.2
ASTM A153
1/2” 24” 150# N/A Spirally Wound /W SS SS 316L/FG, 4.5mm
Gasket
2” 24” 300# N/A Inner & CS Outer Rings Thk, ASME B 16.20
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 29 OF 77

Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
3. To be used only to match Class 300 flange connections at control valves and special equipment.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 30 OF 77

1A4 Piping Material Specification

Service See Appendix A Corrosion Allowance 4 mm

Rating 150 # PWHT NONE Piping Material C.S.

Allowable 1.96 MPa @ -20/38℃

Pressure 1.77 MPa @ 100℃
Items Inch Size Rating. End Tag No. & Main Material
From To Sch./Thk Description
BA-1A41 (Floating Ball,
1/2” 1 1/2” 150# Flanged,RF
Full Bore)
BA-1A42 (Floating Ball,
2” 6” 150# Flanged,RF
Full Bore)
BA-1A43 (Trunnion
8” 24” 150# Flanged,RF Mounted, Full Bore/W
Ball Valve (Note 1)
Gear Operator
BA-1A45 (Floating Ball,
3” 6” 150# Flanged,RF
Reduced Bore)
BA-1A46 (Trunnion
8” 24” 150# Flanged,RF Mounted, Reduced
Bore/W Gear Operator
1/2” 1 1/2” 150# Flanged,RF GA-1A41 (Wedge Gate)
2” 8” 150# Flanged,RF GA-1A42 (Wedge Gate)
2” 8” 150# Flanged,RF GA-1A43 (Flat Gate)
Gate Valve (Note 1)
GA-1A44 (Wedge Gate &
10” 24” 150# Flanged,RF
/W Gear Operator)
GA-1A45 (Flat Gate & /W
10” 24” 150# Flanged,RF
Gear Operator)
GL-1A41 (Spherical
1/2” 1 1/2” 150# Flanged,RF
Disc& Renewable Seat)

GL-1A42 (Spherical Disc

2” 6” 150# Flanged,RF
Globe Valve & Renewable Seat) (Note 1)

GL-1A43 (Spherical Disc

8” 16” 150# Flanged,RF & Renewable Seat With
Gear Operator)

1/2” 1 1/2” 150# Flanged,RF CK-1A41 (Lift)

Check
(Note 1)
Valve
2” 24” 150# Flanged,RF CK-1A42 (Wafer)
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 31 OF 77

1A4 Piping Material Specification

Service See Appendix A Corrosion Allowance 4 mm

Rating 150 # PWHT NONE Piping Material C.S.

Allowable 1.96 MPa @ -20/38℃

Pressure 1.77 MPa @ 100℃
Items Inch Size Rating. End Tag No. & Main Material
From To Sch./Thk Description
BT-1A41 (Three-
2” 6” 150# Flanged,RF
Eccentricity)
Butterfly
BT-1A42 (Three- (Note 1)
Valve
8” 24” 150# Flanged,RF Eccentricity With Gear
Operator)
1/2” 1 1/2” SCH160 BE Seamless, Steel Pipe
2” 2” 5.54mm BE Seamless, Steel Pipe
3” 3” 5.49mm BE Seamless, Steel Pipe
4” 4” 5.56mm BE Seamless, Steel Pipe
6” 6” 6.35mm BE Seamless, Steel Pipe
8” 8” 6.35mm BE Seamless, Steel Pipe API 5L
Pipe 10” 10” 7.09mm BE Seamless, Steel Pipe PSL2.GR.BN,
ASME B36.10M
12” 12” 8.38mm BE Seamless, Steel Pipe
14” 14” 9.53mm BE Seamless, Steel Pipe
16” 16” 9.53mm BE Seamless, Steel Pipe
18” 18” 9.53mm BE Seamless, Steel Pipe
20” 20” 8.74mm BE SAWL, Steel Pipe
24” 24” 9.53mm BE SAWL, Steel Pipe
API 5L
Seamless, Steel Pipe PSL2.GR.BN,
Nipple 1/2” 1 1/2” XXS -
(80mm Long)
ASME B36.10M

Elbow, Tee, Coupling, ASTM A105N,

1/2” 1 1/2” 6000# SW
Cap, Union ASME B16.11

Coupling, Cap, ASTM A105N,

Fittings 1/2” 1 1/2” 3000# NPT Union, ASME B16.11 &
Threadolets MSS SP-97

ASTM A105N,
1/2” 1 1/2” 6000# SW Sockolets
MSS SP 97
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 32 OF 77

1A4 Piping Material Specification

Service See Appendix A Corrosion Allowance 4 mm

Rating 150 # PWHT NONE Piping Material C.S.

Allowable 1.96 MPa @ -20/38℃

Pressure 1.77 MPa @ 100℃
Items Inch Size Rating. End Tag No. & Main Material
From To Sch./Thk Description
2” 2” SCH80 BW
3” 6” SCH40 BW
ASTM A234
8” 8” SCH20 BW Gr.WPB
Elbow (LR) ,Tee, Reducer
10” 16” SCH30 BW Seamless
ASME B16.9
18” 18” 9.53mm BW
Fittings
20” 24” SCH20 BW
1/2” 1 1/2” SCH160 BW
2” 2” SCH80 BW ASTM A105N,
Weldolets
3” 6” SCH40 BW MSS SP 97
8” 8” SCH20 BW
1/2” 24” 150# Flanged,RF Welding Neck(Note 2)
ASTM A105N,
2” 24” 300# Flanged,RF Welding Neck(Note 2,3)
ASME B16.5
1/2” 24” 150# Flanged,RF Blind
Flanges 1/2” 12” 150# - Spectacle Blank ASTM A105N,
14” 24” 150# - Blinds and Spacer ASME B16.48
Orifice Flange Set, 0.5” ASTM A105N,
2” 24” 300# Flanged,RF
socketweld taps (Note 2) ASME B16.36
1/2” 24” 150# N/A Stud Bolts, Alloy
Steel, ASTM
Studs/ Full Length, /W Two HVY
A193-B7 /194-2H,
Hexagonal Nuts, ASME B
Nuts 2” 24” 300# N/A Hot Dip
18.2.1/18.2.2
Galvanized ASTM
A153
1/2” 24” 150# N/A PTFE w/ barium
sulfate GYLON
Gasket Non-Matallic 3510 or equal,
2” 24” 300# N/A 1.6mm Thk,
ASME B 16.21

Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
3. To be used only to match Class 300 flange connections at control valves and special equipment.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 33 OF 77

1C0 Piping Material Specification

Service See Appendix A Corrosion Allowance 0 mm

ASTM A312-
Rating 150 # PWHT NONE Piping Material
TP316L
Allowable 1.5MPa @ -20/38℃
Pressure 1.3 MPa @ 100℃
Inch Size Rating Tag No. &
Items End Main Material
From To Sch./Thk. Description
BA-1C01 (Floating
1/2” 1 1/2” 150# Flanged,RF
Ball, Full Bore)
BA-1C02 (Floating
Ball Valve 2” 6” 150# Flanged,RF (Note 1)
Ball, Full Bore)
BA-1C04 (Floating
3” 6” 150# Flanged,RF
Ball, Reduced Bore)
GL-1C01 (Spherical
1/2” 1 1/2” 150# Flanged,RF Disc& Renewable
Seat)
Globe Valve (Note 1)
GL-1C02 (Spherical
2” 6” 150# Flanged,RF Disc & Renewable
Seat)
Check 1/2” 1 1/2” 150# Flanged,RF CK-1C01 (Lift)
(Note 1)
Valve 2” 6” 150# Flanged,RF CK-1C02 (Wafer)
Seamless, Steel
Pipe 1/2” 6” SCH40S BE ASTM A312-
Pipe
TP316L,
Seamless, Steel
Nipple 1/2” 1 1/2” SCH80S - ASME B36.19M
Pipe( 80mm Long)
ASTM A182-
F316L,
Cap 1/2” 1” 3000# NPT -
ASME B16.11
(Note 4)
ASTM A403 WP
Elbow (LR) ,Tee, 316L,
1/2” 6” SCH40S BW
Reducer Seamless ASME
Fittings B16.9
ASTM A182-
1/2” 6” SCH40S BW Weldolets F316L,
MSS SP 97,
Welding Neck (Note
1/2” 6” 150# Flanged,RF
2) ASTM A182-
Welding Neck (Note F316L, ASME
2” 6” 300# Flanged,RF
2,3) B16.5
1/2” 6” 150# Flanged,RF Blind
Flanges ASTM A182-
1/2” 6” 150# - Spectacle Blank F316L, ASME
B16.48
Orifice Flange Set, ASTM A182-
2” 6” 300# Flanged,RF 0.5” socketweld F316L,
taps (Note 2) ASME B16.36
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 34 OF 77

1C0 Piping Material Specification

Service See Appendix A Corrosion Allowance 0 mm

ASTM A312-
Rating 150 # PWHT NONE Piping Material
TP316L
Allowable 1.5MPa @ -20/38℃
Pressure 1.3 MPa @ 100℃
Inch Size Rating Tag No. &
Items End Main Material
From To Sch./Thk. Description
Full Length, /W Two
HVY Hexagonal Nuts
1/2” 6” 150#
N/A ASME B
18.2.1/18.2.2 Stud Bolts, ASTM
Studs/ Full Length, /W A193 Gr B8M Cl2
Nuts
Two HVY / A194 Gr 8M
2” 6” 300#
N/A
Hexagonal Nuts
ASME B
18.2.1/18.2.2
Phenlic
Electrically
Insulated Retainer
Type F Insulating W/PTFE
Insulation Gasket Kits, Max Electrically
1/2” 6” 150# N/A
Gasket Kits Water Absorption Sealing, Phenlic
1.5%, Integral Sleeves
and Washers,
3.175
mm Thk,
1/2” 6” 150# N/A Spirally Wound /W SS 316L/PTFE,
Gasket SS Inner & CS Outer 4.5mm Thk,
2” 6” 300# N/A Rings ASME B16.20
Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
3..To be used only to match Class 300 flange connections at control valves and special equipment.
4. Use restricted to drains only.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 35 OF 77

1D3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 150 # PWHT YES Piping Material C.S. (NACE)

Allowable 1.96 MPa @ -20/38℃

Pressure 1.58 MPa @ 148.9℃ / 0.34MPa @ 200℃
Items Inch Size Rating. End Tag No. & Main Material
From To Sch./Thk Description
BA-1D31S (Floating
1/2” 1 1/2” 150# Flanged,RF
Ball, Full Bore)
BA-1D32S (Floating
2” 4” 150# Flanged,RF
Ball, Full Bore)
BA-1D34S (Trunnion
6” 24” 150# Flanged,RF Mounted, Full Bore /W
Ball Valve (Note 1)
Gear Operator
BA-1D36S (Floating
3” 4” 150# Flanged,RF
Ball, Reduced Bore)
BA-1D38S (Trunnion
6” 24” 150# Flanged,RF Mounted, Reduced
Bore /W Gear Operator
GA-1D31S (Wedge
1/2” 1 1/2” 150# Flanged,RF
Gate)
GA-1D32S (Wedge
2” 8” 150# Flanged,RF
Gate)
2” 8” 150# Flanged,RF GA-1D34S (Flat Gate)
Gate Valve (Note1)
GA-1D35S (Wedge
10” 24” 150# Flanged,RF Gate & /W Gear
Operator)

GA-1D36S (Flat Gate &

10” 24” 150# Flanged,RF
/W Gear Operator)

GL-1D31S (Spherical
1/2” 1 1/2” 150# Flanged,RF
Disc& Renewable Seat)
GL-1D32S (Spherical
2” 6” 150# Flanged,RF Disc & Renewable
Globe Valve (Note 1)
Seat)
GL-1D33S (Spherical
8” 16” 150# Flanged,RF Disc & Renewable Seat
With Gear Operator)
Check 1/2” 1 1/2” 150# Flanged,RF CK-1D31S (Lift)
(Note1)
Valve 2” 24” 150# Flanged,RF CK-1D32S (Wafer)
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 36 OF 77

1D3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 150 # PWHT YES Piping Material C.S. (NACE)

Allowable 1.96 MPa @ -20/38℃

Pressure 1.58 MPa @ 148.9℃ / 0.34MPa @ 200℃
Items Inch Size Rating. End Tag No. & Main Material
From To Sch./Thk Description

Butterfly
8” 24” 150# Flanged,RF BT-1D31S (Note1)
Valve

1/2” 1 1/2” SCH80 BE Seamless, Steel Pipe

2” 2” 3.91mm BE Seamless, Steel Pipe
3” 3” 4.37mm BE Seamless, Steel Pipe
4” 4” 4.78mm BE Seamless, Steel Pipe
6” 6” 5.56mm BE Seamless, Steel Pipe
API 5L PSL2.Gr BNS
8” 8” 6.35mm BE Seamless, Steel Pipe ASME B36.10M
Pipe
10” 10” 7.09mm BE Seamless, Steel Pipe
12” 12” 8.38mm BE Seamless, Steel Pipe
14” 14” 9.53mm BE Seamless, Steel Pipe
16” 16” 9.53mm BE Seamless, Steel Pipe
18” 18” 9.53mm BE Seamless, Steel Pipe
20” 24” 8.74mm BE SAWL, Steel Pipe

Seamless, Steel Pipe API 5L PSL2 BNS,

Nipple 1/2” 1 1/2” SCH160 -
(80mm Long) ASME B36.10M

ASTM A350 LF2,

ASME B16.11
Cap 1/2” 1” 3000# NPT
Sour Service
(Note 4)
Fittings 1/2” 1 1/2” SCH80 BW
2” 2” SCH40 BW API 5L PSL2.Gr
3” 4” SCH30 BW BNS, Seamless
Elbow (LR) ,Tee, ASME B16.9
6” 6” 5.56mm BW
Reducer, Cap
8” 8” SCH20 BW ASTM A420 WPL6
10” 16” SCH30 BW (for CAP)
18” 18” 9.53mm BW
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 37 OF 77

1D3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 150 # PWHT YES Piping Material C.S. (NACE)

Allowable 1.96 MPa @ -20/38℃

Pressure 1.58 MPa @ 148.9℃ / 0.34MPa @ 200℃
Items Inch Size Rating. End Tag No. & Main Material
From To Sch./Thk Description
API 5L PSL2.Gr
Elbow (LR) ,Tee, BNS, Welded,
20” 24” SCH20 BW
Reducer
ASME B16.9
ASTM A420 WPL6,
20” 24” SCH20 BW Cap Seamless, ASME
B16.9
1/2” 1 1/2” SCH80 BW
2” 2” SCH40 BW ASTM A350 LF2,
3” 4” SCH30 BW Weldolets MSS SP 97
6” 6” 5.56mm BW Sour Service

8” 8” SCH20 BW
1/2” 24” 150# Flanged,RF Welding Neck(Note 2) ASTM A350 LF2，
2” 24” 300# Flanged,RF Welding Neck(Note 2,3) ASME B16.5,
1/2” 24” 150# Flanged,RF Blind Sour Service

1/2” 12” 150# - Spectacle Blank ASTM A350 LF2,

Flanges ASME B16.48
14” 24” 150# - Blinds and Spacer Sour Service
Orifice Flange Set, 0.5” ASTM A350 LF2,
2” 24” 300# Flanged,RF socketweld taps (Note ASME B16.36
2) Sour Service

Studs/ 1/2” 24” 150# N/A Full Length, /W Two Stud Bolts, Alloy
HVY Hexagonal Nuts Steel, ASTM A193-
Nuts 2” 24” 300# N/A ASME B 18.2.1/18.2.2 B7M /194-2HM
1/2” 24” 150# N/A Spirally Wound /W SS SS 316L/FG, 4.5mm
Gasket
2” 24” 300# N/A Inner & CS Outer Rings Thk, ASME B 16.20
Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
3.To be used only to match Class 300 flange connections at control valves and special equipment.
4. Use restricted to drains only.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 38 OF 77

1G0 Piping Material Specification

Service See Appendix A Corrosion Allowance 0 mm

Rating 150 # PWHT NONE Piping Material C.S.(Galvd)

Allowable 1.96 MPa @ -20/38℃

Pressure 1.77 MPa @ 100℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
BA-1G01 (Floating Ball,
1/2” 1 1/2” 800# NPTF
Full Bore)
BA-1G02(Floating Ball,
Ball Valve 2” 4” 150# RF (Note 1)
Full Bore)
BA-1G04(Floating Ball,
3” 4” 150# RF
Reduced Bore)
Gate 1/2” 1 1/2” 800# NPTF GA-1G01 (Wedge Gate)
(Note 1)
Valve 2” 4” 150# RF GA-1G02 (Wedge Gate)
1/2” 1 1/2” 800# NPTF GL-1G01 (Wedge Gate)
Globe
GL-1G02 (Spherical Disc (Note 1)
Valve 2” 4” 150# RF
& Renewable Seat)
Check 1/2” 1 1/2” 800# NPTF CK-1G01 (Lift)
(Note 1)
Valve 2” 4” 150# RF CK-1G02 (Wafer)
Seamless, Hot Dip
1/2” 2” SCH80 NPTM
Galvanised
Pipe API 5L PSL2.GR.BN
Seamless, Hot Dip Galvanized
3” 4” SCH40 NPTM
Galvanised
ASME B36.10M
Seamless, Hot Dip
Nipple 1/2” 4” SCH80 NPTM
Galvanised (80mm Long)
Coupling, Cap,
ASTM A105N+ Galvanised
Union,
1/2” 1 1/2” 3000# NPTF ASME B16.11 & MSS SP-
Threadolets, Elbow 97
Fittings (LR) ,Tee, Reducer
2” 4” 3000# NPTF Full Coupling
ASTM A105N +
Elbow (LR) ,Tee, Galvanised, ASME B 16.11
2” 4” 3000# NPTF
Reducer
1/2” 4” 150# NPTF/RF Thread
ASTM A105N+Galvanised,
4” 3” 150# NPTF/RF Reducing Thread
ASME B16.5
Flanges 1/2” 4” 150# RF Blind
ASTM A105N+Galvanised,
1/2” 4” 150# RF Spectacle Blank
ASME B16.48
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 39 OF 77

1G0 Piping Material Specification

Service See Appendix A Corrosion Allowance 0 mm

Rating 150 # PWHT NONE Piping Material C.S.(Galvd)

Allowable 1.96 MPa @ -20/38℃

Pressure 1.77 MPa @ 100℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
Stud Bolts, Alloy Steel,
Studs/ Full Length, /W Two HVY
ASTM A193-B7/A194-2H,
1/2” 4” 150# N/A Hexagonal Nuts, ASME B
Nuts Hot Dip Galvanized ASTM
18.2.1/18.2.2
A153
PTFE w/ barium sulfate
GYLON 3510 or equal,
Gasket 1/2” 4” 150# N/A Non-Matallic
1.6mm Thk, ASME B
16.21

Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 40 OF 77

3T1 Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 300# PWHT NONE Piping Material C.S.
Allowable 1.96 MPa @ -20/38℃
Pressure 1.2 MPa @ 260℃
Inch Size Rating
Items End Tag No. & Description Main Material
From To Sch./Thk.
GL-3T11 (Spherical
1/2” 1 1/2” 300# Flanged,RF Disc& Renewable
Seat) Bellow Type
GL-3T12 (Spherical
2” 6” 300# Flanged,RF Disc & Renewable
Globe Valve (Note 1)
Seat) Bellow Type
GL-3T13 (Spherical
Disc & Renewable
8” 16” 300# Flanged,RF
Seat With Gear
Operator) Bellow Type
CK-3T11 (Lift)
1/2” 1 1/2” 300# Flanged,RF
Check Bellow Type
(Note 1)
Valve CK-3T12(Wafer)
2” 24” 300# Flanged,RF
Bellow Type

1/2” 1 1/2” SCH80 BE Seamless, Steel Pipe

2” 2” 3.91mm BE Seamless, Steel Pipe
3” 3” 4.37mm BE Seamless, Steel Pipe
4” 4” 4.78mm BE Seamless, Steel Pipe
6” 6” 5.56mm BE Seamless, Steel Pipe API 5L PSL2.GR.BN
Pipe ASME B36.10M
8” 8” 6.35mm BE Seamless, Steel Pipe (Note 3)
10” 10” 7.09mm BE Seamless, Steel Pipe
12” 16” 8.38mm BE Seamless, Steel Pipe
18” 18” 9.53mm BE Seamless, Steel Pipe
20” 24” 8.74mm BE Seamless, Steel Pipe

Seamless, Steel Pipe API 5L PSL2.GR.BN,

Nipple 1/2” 1 1/2” SCH160 -
(80mm Long) ASME B36.10M

A105N,
Cap 1/2” 1” 3000# NPT
ASME B16.11(Note 4)
1/2” 1 1/2” SCH80 BW ASTM A234 Gr.WPB
Fittings Elbow (LR) ,Tee, Seamless
2” 2” SCH40 BW
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 41 OF 77

3T1 Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 300# PWHT NONE Piping Material C.S.
Allowable 1.96 MPa @ -20/38℃
Pressure 1.2 MPa @ 260℃
Inch Size Rating
Items End Tag No. & Description Main Material
From To Sch./Thk.
3” 4” SCH30 BW Reducer (Note 3)
Elbow (LR) ,Tee, ASME B16.9
6” 6” 5.56mm BW
Reducer
8” 8” SCH20 BW
10” 12” SCH30 BW
14” 14” 8.38mm BW
16” 16” 8.38mm BW
18” 18” 9.53mm BW
20 24 SCH20 BW
1/2” 1 1/2” SCH80 BW
2” 2” SCH40 BW
ASTM A105N,
3” 4” SCH30 BW Weldolets
MSS SP 97
6” 6” 5.56mm BW
8” 8” SCH20 BW
Welding Neck(Note
1/2” 24” 300# Flanged,RF ASTM A105N,
2,3)
ASME B16.5
1/2” 24” 300# Flanged,RF Blind
1/2” 12” 300# - Spectacle Blank ASTM A105N,
Flanges
14” 24” 300# - Blinds and Spacer ASME B16.48
Orifice Flange Set, ASTM A105N,
2” 24” 300# Flanged,RF 0.5” socketweld taps
(Note 2,3) ASME B16.36

Stud Bolts, Alloy Steel,

Studs/ Full Length, /W Two ASTM A193-B7 /194-
1/2” 24” 300# N/A HVY Hexagonal Nuts 2H, Hot Dip
Nuts ASME B 18.2.1/18.2.2 Galvanized ASTM
A153
Spirally Wound /W SS
SS 316L/FG, 4.5mm
Gasket 1/2” 24” 300# N/A Inner & CS Outer
Thk, ASME B 16.20
Rings
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 42 OF 77

Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
3. Calculate pipe and fitting wall thickness based on the specific line design conditions. The pressure limit
may be lower than the full flange rating.
4. Use restricted to drains only.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 43 OF 77

1U1(HOLD) Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 150 # PWHT NONE Piping Material C.S.

Allowable 1.96 MPa @ -20/38℃

Pressure 1.58 MPa @ 148.9℃ 1.38 MPa @ 200℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description

BA-1U11 (Floating Ball,

1/2” 1 1/2” 150# Flanged,FF Full Bore, Steam
Jacked Valve)

BA-1U12 (Floating Ball,

Ball Valve (Note 1)
2” 6” 150# Flanged,FF Full Bore, Steam
Jacked Valve)
BA-1U14 (Floating Ball,
2” 6” 150# Flanged,FF Reduced Bore, Steam
Jacked Valve)
Seamless, Steel Pipe
1/2” 1 1/2” SCH80 BE
Steam Jacked
Seamless, Steel Pipe
2” 2” 3.91mm BE
Steam Jacked
Seamless, Steel Pipe
3” 3” 4.37mm BE
Steam Jacked
Seamless, Steel Pipe
4” 4” 4.78mm BE
Steam Jacked
API 5L PSL2.GR.BN
Pipe Seamless, Steel Pipe
6” 6” 5.56mm BE ASME B36.10M
Steam Jacked
Seamless, Steel Pipe
8” 8” 6.35mm BE
Steam Jacked
Seamless, Steel Pipe
10” 10” 7.09mm BE
Steam Jacked

Seamless, Steel Pipe

12” 12” 8.38mm BE
Steam Jacked

Elbow, Tee, Coupling,

ASTM A105N,
1/2” 1 1/2” 3000# SW Cap, Union
ASME B16.11
Fittings Steam Jacked
Sockolets ASTM A105N,
1/2” 1 1/2” 3000# SW
Steam Jacked MSS SP 97
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 44 OF 77

1U1(HOLD) Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 150 # PWHT NONE Piping Material C.S.

Allowable 1.96 MPa @ -20/38℃

Pressure 1.58 MPa @ 148.9℃ 1.38 MPa @ 200℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
1/2” 1 1/2” SCH80 BW
2” 2” SCH40 BW
ASTM A234 Gr.WPB
3” 4” SCH30 BW Elbow (LR) ,Tee, MSS SP-75
Reducer
6” 6” 5.56mm BW Seamless
Fittings Steam Jacked
ASME B16.9
8” 8” SCH20 BW
10” 12” SCH30 BW
1/2” 1 1/2” SCH80 BW Weldolets ASTM A105N,
2” 2” SCH40 BW Steam Jacked MSS SP 97
Welding Neck(Note2) ASTM A105N,
1/2” 12” 150# FlangedFF
Steam Jacked ASME B16.5
Blind ASTM A105N,
1/2” 12” 150# FlangedFF
Steam Jacked ASME B16.5
Flanges Spectacle Blank ASTM A105N,
1/2” 12” 150# -
Steam Jacked ASME B16.48
Orifice Flange Set
ASTM A105N,
2” 12” 300# FlangedFF (Note2)
ASME B16.36
Steam Jacked

Stud Bolts, Alloy Steel,

1/2” 12” 150# N/A
Studs/ Full Length, /W Two ASTM A193-B7 /194-
HVY Hexagonal Nuts 2H, Hot Dip
Nuts ASME B 18.2.1/18.2.2 Galvanized ASTM
2” 12” 300# N/A A153

1/2” 12” 150# N/A

Spirally Wound /W SS
SS 316L/FG, 4.5mm
Gasket Inner & CS Outer
Thk, ASME B 16.20
Rings
2” 12” 300# N/A

Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 45 OF 77

3A1 Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 300 # PWHT NONE Piping Material C.S.
Allowable 4.1 MPa @ -20/38℃
Pressure 3.55 MPa @ 93℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk Description

BA-3A11 (Floating Ball,

800# SW
Full Bore)
1/2” 1 1/2”
BA-3A12 (Floating Ball,
300# Flanged,RF
Full Bore)

BA-3A13 (Floating Ball,

2” 4” 300# Flanged,RF
Full Bore)

BA-3A14 (Trunnion
6” 18” 300# Flanged,RF Mounted, Full Bore /W
Ball Valve Gear Operator (Note 1)

BA-3A15 (All Butt

6” 18” 300# Flanged,RF Welding Underground，
Full Bore Ball Valve)

BA-3A18 (Floating Ball,

3” 4” 300# Flanged,RF
Reduced Bore)

BA-3A19 (Trunnion
6” 18” 300# Flanged,RF Mounted, Reduced Bore
/W Gear Operator

800# SW GA-3A11 (Wedge Gate)

1/2” 1 1/2”
300# Flanged,RF GA-3A12 (Wedge Gate)

2” 8” 300# Flanged,RF GA-3A13 (Wedge Gate)

Gate Valve 2” 8” 300# Flanged,RF GA-3A14 (Flat Gate) (Note 1)

GA-3A15 (Wedge Gate

10” 18” 300# Flanged,RF
& /W Gear Operator)

GA-3A16 ((Flat Gate &

10” 18” 300# Flanged,RF
/W Gear Operator)

GL-3A11 (Spherical
Globe Valve 1/2” 1 1/2” 300# Flanged,RF (Note 1)
Disc)
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 46 OF 77

3A1 Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 300 # PWHT NONE Piping Material C.S.
Allowable 4.1 MPa @ -20/38℃
Pressure 3.55 MPa @ 93℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk Description
GL-3A12 (Spherical Disc
2” 6” 300# Flanged,RF
& Renewable Seat)
GL-3A13 (Spherical Disc
8” 16” 300# Flanged,RF & Renewable Seat With
Gear Operator)

Check 1/2” 1 1/2” 300# Flanged,RF CK-3A11 (Lift)

(Note 1)
Valve 2” 18” 300# Flanged,RF CK-3A12 (Wafer)
Plug Valve 2” 6” 300# Flange. RF PL-3A11 (Note 1)
1/2” 1 1/2” SCH80 BE Seamless, Steel Pipe
2” 2” 3.91mm BE Seamless, Steel Pipe
3” 3” 4.37mm BE Seamless, Steel Pipe
4” 4” 4.78mm BE Seamless, Steel Pipe
6” 6” 5.56mm BE Seamless, Steel Pipe
API 5L PSL2.GR.BN
8” 8” 6.35mm BE Seamless, Steel Pipe ASME B36.10M
Pipe
10” 10” 7.09mm BE Seamless, Steel Pipe
12” 12” 8.38mm BE Seamless, Steel Pipe
14” 14” 9.53mm BE Seamless, Steel Pipe
16” 16” 9.53 mm BE Seamless, Steel Pipe
11.13
18” 18” BE Seamless, Steel Pipe
mm
Seamless, Steel Pipe API 5L PSL2 GR.BN
Nipple 1/2” 1 1/2” SCH160 -
(80mm Long) ASME B36.10M
Elbow, Tee, Coupling, ASTM A105,
1/2” 1 1/2” 3000# SW
Cap, Union ASME B16.11
ASTM A105N,
Coupling, Cap, Union,
Fittings 1/2” 1 1/2” 3000# NPTF ASME B16.11 &MSS
Threadolets
SP-97
ASTM A105N,
1/2” 1 1/2” 3000# SW Sockolets
MSS SP 97
Fittings 1/2” 1 1/2” SCH80 BW Elbow (LR) ,Tee, ASTM A234 Gr.WPB
Reducer Seamless
2” 2” SCH40 BW
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 47 OF 77

3A1 Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 300 # PWHT NONE Piping Material C.S.
Allowable 4.1 MPa @ -20/38℃
Pressure 3.55 MPa @ 93℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk Description
3” 4” SCH30 BW ASME B16.9
6” 6” 5.56mm BW
8” 8” SCH20 BW
10” 14” SCH30 BW
16” 16” SCH30 BW
18” 18” SCH30 BW
1/2” 1 1/2” SCH80 BW
2” 2” SCH40 BW
ASTM A105N
3” 4” SCH30 BW Weldolets
MSS SP 97
6” 6” 5.56mm BW
8” 8” SCH20 BW
1/2” 18” 300# Flanged,RF Welding Neck (Note 2) ASTM A105N,
1/2” 18” 300# Flanged,RF Blind ASME B16.5
1/2” 12” 300# - Spectacle Blank ASTM A105N,
Flanges
14” 18” 300# - Blinds and Spacer ASME B16.48
Orifice Flange Set, 0.5” ASTM A105N,
2” 18” 300# Flanged,RF
socketweld taps (Note 2) ASME B16.36
Stud Bolts, Alloy
Studs/ Full Length, /W Two Steel, ASTM A193-
1/2” 18” 300# N/A HVY Hexagonal Nuts, B7 /194-2H, Hot Dip
Nuts ASME B 18.2.1/18.2.2 Galvanized ASTM
A153
Spirally Wound /W SS SS 316L/FG, 4.5mm
Gasket 1/2” 18” 300# N/A
Inner & CS Outer Rings Thk, ASME B 16.20
Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 48 OF 77

3X3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 300 # PWHT YES Piping Material C.S.(NACE)

Allowable 4.7 MPa @ -20/38℃

Pressure 4.7 MPa @ 90℃
Items Inch Size Rating. End Tag No. & Main Material
From To Sch./Thk Description

1/2” 3/4” SCH160 BE Seamless, Steel Pipe

1
1” SCH80 BE Seamless, Steel Pipe
1/2”

2” 2” 4.78mm BE Seamless, Steel Pipe

3” 3” 4.78mm BE Seamless, Steel Pipe

4” 4” 6.02mm BE Seamless, Steel Pipe

API 5L PSL2
6” 6” 6.35mm BE Seamless, Steel Pipe Gr.BNS, ASME
B36.10M
Pipe
8” 8” 7.92mm BE Seamless, Steel Pipe

10” 10” 8.74mm BE Seamless, Steel Pipe

12” 12” 9.53mm BE Seamless, Steel Pipe

14” 16” 9.53mm BE Seamless, Steel Pipe

20” 20” 12.7mm BE Seamless, Steel Pipe

API 5L
10.31mm PSL2.GR.X52NS
24” 24” BE SAWL Steel Pipe ASME B36.10M
11.13mm(CPF1)
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 49 OF 77

3X3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 300 # PWHT YES Piping Material C.S.(NACE)

Allowable 4.7 MPa @ -20/38℃

Pressure 4.7 MPa @ 90℃
Items Inch Size Rating. End Tag No. & Main Material
From To Sch./Thk Description
API 5L PSL2
1 Seamless, Steel Pipe
Nipple 1/2” SCH160 - Gr.BNS, ASME
1/2” (80mm Long)
B36.10M
ASTM A350 LF2,
ASME B16.11,
Cap 1/2” 1” 3000# NPT
Sour Service (Note
3)
ASTM A182 F316,
ASME B16.11, As
Plug 1/2” 1/2” NPT Hex Plug Per NACE
MR0175/ISO15156
(Note 4)
Body/Bonnet-
Needle 316SS, Trim-alloy
1/2” 1/2” 2500# FNPT
Valve 400, As Per NACE
MR0175/ISO15156.
Fittings 3” 3” 4.78mm BW

4” 4” 6.02mm BW

6” 6” 6.35mm BW
6D Hot Bend With API 5L
8” 8” 7.92mm BW 250mm tangent PSL2.GR.BNS,
Seamless,
Barred Tee,
10” 10” 8.74mm BW ISO 15590-1 for
Isolation Joint Hot Bend
12” 12” 9.53mm BW
14” 16” 9.53mm BW
20” 20” 12.7mm BW
6D Hot Bend With API 5L PSL2.GR.
10.31mm 500mm tangent X52NS, Welded
24” 24” BW
11.13mm(CPF1) Barred Tee, ISO 15590-1 for
Isolation Joint Hot Bend
1/2” 3/4” SCH160 BW Elbow(LR), Tee, API 5L PSL2
Reducer Gr.BNS, Seamless
1 (For CPF1 No PIG
1” SCH80 BW ASME B16.9
1/2”
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 50 OF 77

3X3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 300 # PWHT YES Piping Material C.S.(NACE)

Allowable 4.7 MPa @ -20/38℃

Pressure 4.7 MPa @ 90℃
Items Inch Size Rating. End Tag No. & Main Material
From To Sch./Thk Description
2” 2” 4.78mm BW Pass)

3” 3” 4.78mm BW
4” 4” SCH40 BW
6” 6” 6.35mm BW
8” 12” SCH40 BW
14” 16” SCH30 BW
Elbow(LR), Tee, API 5L PSL2
Reducer
20” 20” SCH30 BW Gr.BNS, Welded,
(For CPF1 No PIG
Pass) ASME B16.9

1/2” 3/4” SCH160 BW

1
1” SCH80 BW
1/2”
ASTM A350 LF2
2” 2” SCH80 BW
Fittings Weldolets MSS SP 97,
3” 4” SCH40 BW Sour Service
6” 6” SCH40 BW

8” 8” SCH40 BW

Welding Neck (Note 2) ASTM A350 LF2,

1/2” 20” 300# Flanged,RF Anchor Flange ASME B16.5, Sour
Blind Service
Welding Neck (Note 2) ASTM A694 F52,
24” 24” 300# Flanged,RF Anchor Flange ASME B16.5, Sour
Blind Service
Flanges
1/2” 12” 300# - Spectacle Blank ASTM A350 LF2,
ASME B16.48,
14” 20” 300# - Blinds and Spacer Sour Service

ASTM A350 LF2,

Orifice Flange Set ASME B16.36,
2” 20” 300# Flanged,RF
(Note 2)
Sour Service
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 51 OF 77

3X3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 300 # PWHT YES Piping Material C.S.(NACE)

Allowable 4.7 MPa @ -20/38℃

Pressure 4.7 MPa @ 90℃
Items Inch Size Rating. End Tag No. & Main Material
From To Sch./Thk Description

Studs/ Full Length, /W Two Stud Bolts, Alloy

1/2” 24” 300# N/A HVY Hexagonal Nuts Steel, ASTM A193-
Nuts ASME B 18.2.1/18.2.2 B7M /194-2HM
Spirally Wound /W SS SS 316L/FG,
Gasket 1/2” 24” 300# N/A Inner & CS Outer 4.5mm Thk, ASME
Rings B 16.20
Notes:
1. Valves selection of piping class 3X3 follows the piping class 3D3.
2. Thickness to suit pipe.
3. Use restricted to drains only.
4. Use restricted to needle valve only.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 52 OF 77

3C0 Piping Material Specification

Service See Appendix A Corrosion Allowance 0 mm

Rating 300 # PWHT NONE Piping Material ASTM A312-TP316L

Allowable 4.1 MPa @ -20/38℃

Pressure 3.4 MPa @ 100℃
Inch Size Rating
Items End Tag No. & Description Main Material
From To Sch./Thk.
BA-3C01 (Floating Ball,
1/2” 1 1/2” 300# Flanged,RF
Full Bore)
BA-3C02 (Floating Ball,
Ball Valve 2” 6” 300# Flanged,RF (Note 1)
Full Bore)
BA-3C04 (Floating Ball,
3” 6” 300# Flanged,RF
Reduced Bore)
GL-3C01 (Spherical
1/2” 1 1/2” 300# Flanged,RF Disc& Renewable
Seat)
Globe Valve (Note 1)
GL-3C02 (Spherical
2” 6” 300# Flanged,RF Disc & Renewable
Seat)
Check 1/2” 1 1/2” 300# Flanged,RF CK-3C01 (Lift)
(Note 1)
Valve 2” 6” 300# Flanged,RF CK-3C02 (Wafer)
Pipe 1/2” 6” SCH40S BE Seamless, Steel Pipe
ASTM A312-TP316L
Seamless, Steel Pipe ASME B36.19M
Nipple 1/2” 1 1/2” SCH40S -
(80mm Long)
ASTM A182-F316L,
Cap 1/2” 1” 3000# NPT ASME B16.11
(Note 3)
ASTM A403 WP
Elbow (LR) ,Tee, 316L, Seamless
1/2” 6” SCH40S BW
Reducer
Fittings ASME B16.9
ASTM A182-F316L
1/2” 6” SCH40S BW Weldolets
MSS SP 97
1/2” 6” 300# Flanged,RF Welding Neck(Note 2) ASTM A182-F316L,
1/2” 6” 300# Flanged,RF Blind ASME B16.5
ASTM A182-F316L,
Flanges 1/2” 6” 300# - Spectacle Blank
ASME B16.48
Orifice Flange Set, 0.5”
ASTM A182-F316L,
2” 6” 300# Flanged,RF socketweld taps (Note
ASME B16.36
2)
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 53 OF 77

3C0 Piping Material Specification

Service See Appendix A Corrosion Allowance 0 mm

Rating 300 # PWHT NONE Piping Material ASTM A312-TP316L

Allowable 4.1 MPa @ -20/38℃

Pressure 3.4 MPa @ 100℃
Inch Size Rating
Items End Tag No. & Description Main Material
From To Sch./Thk.
Full Length, /W Two Stud Bolts, ASTM
Studs/
1/2” 6” 300# N/A HVY Hexagonal Nuts A193 Gr B8M Cl2 /
Nuts ASME B 18.2.1/18.2.2 A194 Gr 8M
Phenlic Electrically
Insulated Retainer
Type F Insulating
W/PTFE Electrically
Insulation Gasket Kits, Max
Gasket Kits
1/2” 6” 300# N/A Water Absorption
Sealing, Phenlic
Integral Sleeves and
1.5%,
Washers, 3.175
mm Thk,
Spirally Wound /W SS SS 316L/PTFE,
Gasket 1/2” 6” 300# N/A Inner & CS Outer 4.5mm Thk, ASME
Rings B 16.20

Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
3. Use restricted to drains only.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 54 OF 77

6C0 Piping Material Specification

Service See Appendix A Corrosion Allowance 0 mm

Rating 600 # PWHT NONE Piping Material ASTM A312-TP316L

Allowable 8.2 MPa @ -20/38℃

Pressure 6.9 MPa @ 100℃
Inch Size Rating
Items End Tag No. & Description Main Material
From To Sch./Thk.
BA-6C01 (Floating Ball,
1/2” 1 1/2” 600# Flanged,RF
Full Bore)
BA-6C02 (Floating Ball,
Ball Valve 2” 6” 600# Flanged,RF (Note 1)
Full Bore)
BA-6C04 (Floating Ball,
3” 6” 600# Flanged,RF
Reduced Bore)
GL-6C01 (Spherical
1/2” 1 1/2” 600# Flanged,RF Disc& Renewable
Seat)
Globe Valve (Note 1)
GL-6C02 (Spherical
2” 6” 600# Flanged,RF Disc & Renewable
Seat)
Check 1/2” 1 1/2” 600# Flanged,RF CK-6C01 (Lift)
(Note 1)
Valve 2” 6” 600# Flanged,RF CK-6C02 (Wafer)
Pipe 1/2” 6” SCH40S BE Seamless, Steel Pipe
ASTM A312-TP316L
Seamless, Steel Pipe ASME B36.19M
Nipple 1/2” 1 1/2” SCH80S -
(80mm Long)
ASTM A182-F316L,
Cap 1/2” 1” 3000# NPT ASME B16.11
(Note 3)
ASTM A403 WP
Elbow (LR) ,Tee, 316L, Seamless
1/2” 6” SCH40S BW
Reducer
Fittings ASME B16.9
ASTM A182-F316L
1/2” 6” SCH40S BW Weldolets
MSS SP 97
1/2” 6” 600# Flanged,RF Welding Neck(Note 2) ASTM A182-F316L,
1/2” 6” 600# Flanged,RF Blind ASME B16.5
ASTM A182-F316L,
Flanges 1/2” 6” 600# - Spectacle Blank
ASME B16.48
Orifice Flange Set, 0.5”
ASTM A182-F316L,
2” 6” 600# Flanged,RF socketweld taps (Note
ASME B16.36
2)
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 55 OF 77

6C0 Piping Material Specification

Service See Appendix A Corrosion Allowance 0 mm

Rating 600 # PWHT NONE Piping Material ASTM A312-TP316L

Allowable 8.2 MPa @ -20/38℃

Pressure 6.9 MPa @ 100℃
Inch Size Rating
Items End Tag No. & Description Main Material
From To Sch./Thk.
Full Length, /W Two Stud Bolts, ASTM
Studs/
1/2” 6” 600# N/A HVY Hexagonal Nuts A193 Gr B8M Cl2 /
Nuts ASME B 18.2.1/18.2.2 A194 Gr 8M
Phenlic Electrically
Insulated Retainer
Type F Insulating
W/PTFE Electrically
Insulation Gasket Kits, Max
Gasket Kits
1/2” 6” 600# N/A Water Absorption
Sealing, Phenlic
Integral Sleeves and
1.5%,
Washers, 3.175
mm Thk,
Spirally Wound /W SS SS 316L/PTFE,
Gasket 1/2” 6” 600# N/A Inner & CS Outer 4.5mm Thk, ASME
Rings B 16.20

Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
3. Use restricted to drains only.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 56 OF 77

3D3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 300 # PWHT YES Piping Material C.S. (NACE)
Allowable 4.7 MPa @ -20/38℃
Pressure 4.7 MPa @ 90℃

Items Inch Size Rating End Tag No. & Main Material

From To Sch./Thk. Description

BA-3D31S (Floating
1/2” 1 1/2” 300# Flanged,RF
Ball, Full Bore)
BA-3D32S (Floating Ball
2” 4” 300# Flanged,RF
Mounted, Full Bore)
BA-3D33S (Trunnion
6” 24” 300# Flanged,RF Mounted, Full Bore /W
Ball Valve Gear Operator (Note 1)
BA-3D35S (Floating Ball
3” 4” 300# Flanged,RF Mounted, Reduced
Bore)
BA-3D36S (Trunnion
6” 24” 300# Flanged,RF Mounted, Reduced Bore
/W Gear Operator
GA-3D31S (Wedge
1/2” 1 1/2” 300# Flanged,RF
Gate)
GA-3D32S (Wedge
2” 8” 300# Flanged,RF
Gate)
2” 8” 300# Flanged,RF GA-3D33S (Flat Gate)
Gate Valve (Note 1)
GA-3D34S (Wedge
10” 24” 300# Flanged,RF Gate & /W Gear
Operator)
GA-3D35S (Flat Gate &
10” 24” 300# Flanged,RF
/W Gear Operator)
GL-3D31S (Spherical
1/2” 1 1/2” 300# Flanged,RF
Disc& Renewable Seat)
GL-3D32S (Spherical
2” 6” 300# Flanged,RF
Globe Valve Disc & Renewable Seat) (Note 1)
GL-3D33S (Spherical
8” 16” 300# Flanged,RF Disc & Renewable Seat
With Gear Operator)
Check 1/2” 1 1/2” 300# Flanged,RF CK-3D31S (Lift)
(Note 1)
Valve 2” 24” 300# Flanged,RF CK-3D32S (Wafer)
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 57 OF 77

3D3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 300 # PWHT YES Piping Material C.S. (NACE)
Allowable 4.7 MPa @ -20/38℃
Pressure 4.7 MPa @ 90℃

Items Inch Size Rating End Tag No. & Main Material

From To Sch./Thk. Description

1/2” 3/4” SCH160 BE Seamless, Steel Pipe
1” 1 1/2” SCH80 BE Seamless, Steel Pipe
2” 2” 4.78mm BE Seamless, Steel Pipe
3” 3” 5.49mm BE Seamless, Steel Pipe
4” 4” 6.02mm BE Seamless, Steel Pipe
6” 6” 7.11mm BE Seamless, Steel Pipe API 5L
PSL2.GR.BNS,
Pipe 8” 8” 7.92mm BE Seamless, Steel Pipe ASME B36.10M
10” 10” 8.74mm BE Seamless, Steel Pipe (Note 3)
12” 12” 9.53mm BE Seamless, Steel Pipe
14” 14” 10.31mm BE Seamless, Steel Pipe
16” 16” 11.0mm BE Seamless, Steel Pipe C.

20” 20” 13.0mm BE Seamless, Steel Pipe

24” 24” 15.88mm BE SAWL, Steel Pipe
API 5L
Seamless, Steel Pipe
Nipple 1/2” 1 1/2” XXS - PSL2.GR.BNS,,
(80mm Long)
ASME B36.10M
ASTM A350 LF2,
ASME B16.11,
Cap 1/2” 1” 6000# NPT
Sour Service
(Note 4)
1/2” 3/4” SCH160 BW
1” 1 1/2” SCH80 BW API 5L
PSL2.GR.BNS,
2” 2” 4.78mm BW Elbow (LR) ,Tee,
Fittings Seamless
3” 12” SCH40 BW Reducer
ASME B16.9
14” 14” 10.31mm BW (Note 3)
16” 16” 11.0mm BW
C.

Elbow (LR) ,Tee, API 5L

20” 20” 13.0mm BW
Reducer PSL2.GR.BNS,
Welded
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 58 OF 77

3D3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 300 # PWHT YES Piping Material C.S. (NACE)
Allowable 4.7 MPa @ -20/38℃
Pressure 4.7 MPa @ 90℃

Items Inch Size Rating End Tag No. & Main Material

From To Sch./Thk. Description

ASME B16.9
24” 24” 15.88mm BW (Note 3)

1/2” 3/4” SCH160 BW

ASTM A350 LF2,
1” 2” SCH80 BW
Fittings Weldolets MSS SP 97,
3” 8” SCH40 BW Sour Service

1/2” 24” 300# Flanged,RF Welding Neck(Note 2,3) ASTM A350 LF2,
ASME B16.5,
1/2” 24” 300# Flanged,RF Blind Sour Service
1/2” 12” 300# - Spectacle Blank ASTM A350 LF2,
Flanges ASME B16.48,
14” 24” 300# - Blinds and Spacer Sour Service
Orifice Flange Set, 0.5” ASTM A350 LF2,
2” 24” 300# Flanged,RF socketweld taps (Note ASME B16.36,
2,3) Sour Service

Studs/ Full Length, /W Two Stud Bolts, Alloy

1/2” 24” 300# N/A HVY Hexagonal Nuts Steel, ASTM A193-
Nuts ASME B 18.2.1/18.2.2 B7M /194-2HM
SS 316L/FG,
Spirally Wound /W SS
Gasket 1/2” 24” 300# N/A 4.5mm Thk, ASME
Inner & CS Outer Rings
B 16.20

Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
3. Calculate pipe and fitting wall thickness based on the specific line design conditions. The pressure limit
may be lower than the full flange rating.
4. Use restricted to drains only.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 59 OF 77

6A1 Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 600 # PWHT NONE Piping Material C.S.

Allowable 9.0 MPa @ 0/38℃

Pressure 9.0 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
BA-6A11 (Floating Ball,
800# SW
Full Bore)
1/2” 1 1/2”
BA-6A12 (Floating Ball,
600# Flanged,RF
Full Bore)
BA-6A13 (Floating Ball,
2” 4” 600# Flanged,RF
Full Bore)
BA-6A14 (Trunnion
6” 24” 600# Flanged,RF Mounted, Full Bore /W
Gear Operator
Ball Valve BA-6A15 (Single Piece (Note 1)
But-Welding
6” 24” 600# Flanged,RF
Underground, Full Bore
Ball Valve)
BA-6A18 (Floating Ball,
3” 4” 600# Flanged,RF
Reduced Bore)

6” 24” 600# Flanged,RF BA-6A19 (Trunnion

Mounted, Reduced
Bore /W Gear Operator

800# SW GA-6A11(Wedge Gate)

1/2” 1 1/2”
600# Flanged,RF GA-6A12(Wedge Gate)
2” 4” 600# Flanged, Rf GA-6A13(Wedge Gate)
2” 4” 600# Flanged, Rf GA-6A14 (Flat Gate)
Gate Valve GA-6A15(Wedge Gate (Note 1)
6” 24” 600# Flanged,RF
& /W Gear Operator)
GA-6A16(Flat Gate &
6” 24” 600# Flanged,RF
/W Gear Operator)
GA-6A17 (All Butt
2” 6” 600# Flanged,RF Welding Underground
Plate Gate Valve)
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 60 OF 77

6A1 Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 600 # PWHT NONE Piping Material C.S.

Allowable 9.0 MPa @ 0/38℃

Pressure 9.0 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description

GL-6A11 (Spherical
1/2” 1 1/2” 600# Flanged,RF
Disc& Renewable Seat)

GL-6A12 (Spherical
Globe Valve 2” 4” 600# Flanged,RF Disc & Renewable (Note 1)
Seat)
GL-6A13 (Spherical
6” 16” 600# Flanged,RF Disc & Renewable Seat
With Gear Operator)
1/2” 1 1/2” 600# Flanged,RF CK-6A11 (Lift)
Check
(Note 1)
Valve 2” 24” 600# Flanged,RF CK-6A12 (Wafer)

1/2” 1 1/2” SCH80 BE Seamless, Steel Pipe

2” 2” 3.91mm BE Seamless, Steel Pipe
3” 3” 4.37mm BE Seamless, Steel Pipe
4” 4” 5.16mm BE Seamless, Steel Pipe
6” 6” 7.11mm BE Seamless, Steel Pipe
8” 8” 9.53mm BE Seamless, Steel Pipe C. API 5L
10” 10” 11.13mm BE Seamless, Steel Pipe PSL2.GR.BN,
Pipe ASME B36.10M
12” 12” 12.70mm BE Seamless, Steel Pipe (Note 3)
14” 14” 14.27mm BE Seamless, Steel Pipe C.
16” 16” 15.88mm BE Seamless, Steel Pipe
18” 18” 17.48mm BE Seamless, Steel Pipe
20” 20” 19.05mm BE SAWL, Steel Pipe
24” 24” 23.83mm BE SAWL, Steel Pipe C.

API 5L
Seamless, Steel
Nipple 1/2” 1 1/2” SCH160 - PSL2.GR.BN,
Pipe(80mm Long)
ASME B36.10M
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 61 OF 77

6A1 Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 600 # PWHT NONE Piping Material C.S.

Allowable 9.0 MPa @ 0/38℃

Pressure 9.0 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
Elbow, Tee, Coupling, ASTM A105N,
1/2” 1 1/2” 6000# SW
Cap, Union ASME B16.11
ASTM A105N,
Coupling, Cap, Union,
1/2” 1 1/2” 3000# NPTF ASME B16.11
Threadolets
&MSS SP-97
Fittings
ASTM A105N,
1/2” 1 1/2” 6000# SW Sockolets
MSS SP 97
ASTM A105N,
STD X MSS SP 97, ASME
2” 2” BW X RF Flange-olet
600# B16.5(TOTAL
LENGTH 6”)
1/2” 1 1/2” SCH80 BW
2” 2” SCH40 BW
3” 3” SCH30 BW
4” 4” 5.16mm BW
6” 6” SCH40 BW
ASTM A234
C.
8” 8” 9.53mm BW Gr.WPB
Elbow (LR) ,Tee ,Cap , Seamless
Fittings 10” 10” 11.13mm BW
Reducer
12” 12” 12.70mm BW ASME B16.9
(Note 3)
14” 14” 14.27mm BW C.

16” 16” 15.88mm BW

18” 18” 17.48mm BW
20” 20” 19.05mm BW
C.
24” 24” 23.83mm BW
1/2” 1 1/2” SCH80 BW
2” 2” SCH40 BW
ASTM A105N,
Fittings 3” 3” SCH30 BW Weldolets
MSS SP 97
4” 6” SCH40 BW
8” 8” 9.53mm BW C.

Flanges 1/2” 24” 600# Flanged,RF Welding Neck(Note 2,3) ASTM A105N,
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 62 OF 77

6A1 Piping Material Specification

Service See Appendix A Corrosion Allowance 1 mm

Rating 600 # PWHT NONE Piping Material C.S.

Allowable 9.0 MPa @ 0/38℃

Pressure 9.0 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
1/2” 24” 600# Flanged,RF Blind ASME B16.5
1/2” 8” 600# - Spectacle Blank ASTM A105N,
10” 24” 600# - Blinds and Spacer ASME B16.48
Orifice Flange Set, 0.5”
ASTM A105N,
2” 24” 600# Flanged,RF socketweld taps (Note
ASME B16.36
2,3)
Stud Bolts, Alloy
Studs/ Full Length, /W Two Steel, ASTM A193-
1/2” 24” 600# N/A HVY Hexagonal Nuts B7 /194-2H, Hot
Nuts ASME B 18.2.1/18.2.2 Dip Galvanized
ASTM A153
SS 316L/FG,
Spirally Wound /W SS
Gasket 1/2” 24” 600# N/A 4.5mm Thk, ASME
Inner & CS Outer Rings
B 16.20
Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
3. Calculate pipe and fitting wall thickness based on the specific line design conditions. The pressure limit
may be lower than the full flange rating.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 63 OF 77

6Q0
Piping Material Specification
(HOLD)
Service See Appendix A Corrosion Allowance 0 mm
Rating 600 # PWHT NONE Piping Material C.S.

Allowable 9.0 MPa @ 0/38℃

Pressure 9.0 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
API 5L PSL2.Gr.BN,
10” 10” 7.09mm BE ERW ASME B36.10M
Pipe
SAWH/SAWL, Steel
24” 24” 12.7mm BE API 5L PSL2.X60
Pipe
ASTM A694 F60,
Elbow, Tee, Coupling,
1/2” 1 1/2” 6000# SW ASME B16.11,
Cap, Union
Seamless
ASTM A694 F60,
Coupling, Cap, Union, Seamless
1/2” 1 1/2” 3000# NPTF
Threadolets ASME B16.11 &MSS
SP-97
ASTM A694 F60,
1/2” 1 1/2” 6000# SW Sockolets MSS SP 97,
Seamless
Hot Bend With 250mm API 5L PSL2 Gr.BN,
tangent, Barred Tee, MSS SP-75
10” 10” SCH30 BW Reducer, CP, Seamless
Fittings Isolation Joint ASME B16.9
API 5L
Hot Bend With 500mm PSL2.GR.X52BN,
tangent, Barred Tee, MSS SP-75
24” 24” SCH30 BW Reducer, CP, ASME B16.9
Isolation Joint ISO 15590 for Hot
Bend
1/2” 1 1/2” SCH80 BW
2” 2” SCH40 BW
3” 4” SCH30 BW ASTM A694 F60,
Weldolets
6” 6” SCH40 BW MSS SP 97

8” 8” SCH60 BW
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 64 OF 77

6Q0
Piping Material Specification
(HOLD)
Service See Appendix A Corrosion Allowance 0 mm
Rating 600 # PWHT NONE Piping Material C.S.

Allowable 9.0 MPa @ 0/38℃

Pressure 9.0 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
Welding Neck(Note 2) ASTM A694 F60,
1/2” 24” 600# Flanged,RF
Anchor Flange ASME B16.5
ASTM A694 F60,
1/2” 24” 600# Flanged,RF Blind
ASME B16.5
Flanges
1/2” 8” 600# - Spectacle Blank ASTM A694 F60,
10” 24” 600# - Blinds and Spacer ASME B16.48
Orifice Flange Set (Note ASTM A694 F60,
2” 24” 600# Flanged,RF
2) 0.5” socketweld taps ASME B16.36
Stud Bolts, Alloy
Studs/ Full Length, /W Two Steel, ASTM A193-
1/2” 24” 600# N/A HVY Hexagonal Nuts, B7 /194-2H, Hot Dip
Nuts ASME B 18.2.1/18.2.2 Galvanized ASTM
A153
Spirally Wound /W SS SS 316L/FG, 4.5mm
Gasket 1/2” 24” 600# N/A
Inner & CS Outer Rings Thk, ASME B 16.20
Notes:
1. Valves selection refers to piping class 6A1.
2. Thickness to suit pipe.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 65 OF 77

6D3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 600 # PWHT YES Piping Material C.S. (NACE)

Allowable 9.0MPa @ 0/38℃

Pressure 9.0 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
BA-6D31s (Floating
1/2” 1 1/2” 600# Flanged,RF
Ball, Full Bore)
BA-6D32s (Floating
2” 4” 600# Flanged,RF Ball Mounted, Full
Bore)
BA-6D33s (Trunnion
6” 12” 600# Flanged,RF Mounted, Full Bore /W
Ball Valve Gear Operator (Note 1)
BA-6D35s (Floating
3” 4” 600# Flanged,RF Ball Mounted,
Reduced Bore)
BA-6D36s (Trunnion
Mounted, Reduced
6” 12” 600# Flanged,RF
Bore /W Gear
Operator
GA-6D31s (Wedge
1/2” 1 1/2” 600# Flanged,RF
Gate)
GA-6D32s (Wedge
2” 4” 600# Flanged,RF
Gate)
2” 4” 600# Flanged,RF GA-6D33s (Flat Gate)
Gate Valve (Note 1)
GA-6D34s (Wedge
6” 8” 600# Flanged,RF Gate & /W Gear
Operator)
GA-6D35s (Flat Gate
6” 12” 600# Flanged,RF
& /W Gear Operator)
GL-6D31s (Spherical
1/2” 1 1/2” 600# Flanged,RF Disc& Renewable
Seat)
GL-6D32s (Spherical
2” 4” 600# Flanged,RF Disc & Renewable
Globe Valve (Note 1)
Seat)
GL-6D33s (Spherical
Disc & Renewable
6” 12” 600# Flanged,RF
Seat With Gear
Operator)
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 66 OF 77

6D3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 600 # PWHT YES Piping Material C.S. (NACE)

Allowable 9.0MPa @ 0/38℃

Pressure 9.0 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
Check 1/2” 1 1/2” 600# Flanged,RF CK-6D31s (Lift)
(Note 1)
Valve 2” 8” 600# Flanged,RF CK-6D32s (Wafer)
1/2” 1 1/2” SCH160 BE Seamless, Steel Pipe
2” 2” 6.35mm BE Seamless, Steel Pipe
3” 3” 7.14mm BE Seamless, Steel Pipe
API 5L PSL2 Gr.BNS
Pipe 4” 4” 8.56mm BE Seamless, Steel Pipe To ASME B36.10M
6” 6” 10.97mm BE Seamless, Steel Pipe
8” 8” 12.70mm BE Seamless, Steel Pipe
10” 10” 15.09mm BE Seamless, Steel Pipe
12” 12” 17.48mm BE Seamless, Steel Pipe
Seamless, Steel Pipe API 5L PSL2 Gr.BNS
Nipple 1/2” 1 1/2” XXS -
(80mm Long) To ASME B36.10M
ASTM A350 LF2,
ASME B16.11,
Cap 1/2” 1” 6000# NPT
Sour Service
(Note 3),
1/2” 1 1/2” SCH160 BW API 5L PSL2 Gr.BNS
Elbow (LR) ,Tee, Seamless
2” 2” 6.35mm BW
Reducer
3” 12” SCH80 BW ASME B16.9
Fittings
1/2” 1 1/2” SCH160 BW ASTM A350 LF2,
2” 2” 6.35mm BW Weldolets MSS SP 97,
3” 3” SCH80 BW Sour Service
Flanges 1/2” 12” 600# Flanged,RF Welding Neck(Note 2) ASTM A350 LF2,
ASME B16.5,
1/2” 12” 600# Flanged,RF Blind Sour Service
1/2” 8” 600# - Spectacle Blank ASTM A350 LF2,
ASME B16.48,
10” 12” 600# Blinds and Spacer Sour Service
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 67 OF 77

6D3 Piping Material Specification

Service See Appendix A Corrosion Allowance 3 mm

Rating 600 # PWHT YES Piping Material C.S. (NACE)

Allowable 9.0MPa @ 0/38℃

Pressure 9.0 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
Orifice Flange Set, ASTM A350 LF2,
2” 12” 600# Flanged,RF 0.5” socketweld taps ASME B16.36,
(Note 2) Sour Service

Studs/ Full Length, /W Two Stud Bolts, Alloy

1/2” 12” 600# N/A HVY Hexagonal Nuts, Steel, ASTM A193-
Nuts ASME B 18.2.1/18.2.2 B7M /194-2HM
Spirally Wound /W SS
SS 316L/FG, 4.5mm
Gasket 1/2” 12” 600# N/A Inner & CS Outer
Thk, ASME B 16.20
Rings

Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
3. Use restricted to drains only.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 68 OF 77

15A4
Piping Material Specification
(HOLD)
Service See Appendix A Corrosion Allowance 4 mm
Rating 1500 # PWHT Per B31.3 Piping Material C.S.

Allowable 25.5 MPa @ 0/38℃

Pressure 22.54 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
BA-15A41 (Floating
1/2” 1 1/2” 1500# Flanged,RJ
Ball, Full Bore)
BA-15A42 (Floating
2” 4” 1500# Flanged,RJ
Ball, Full Bore)
BA-15A43 (Trunnion
6” 20” 1500# Flanged,RJ Mounted, Full Bore /W
Ball Valve Gear Operator (Note 1)
BA-15A45 (Floating
3” 4” 1500# Flanged,RJ
Ball, Reduced Bore)
BA-15A46 (Trunnion
Mounted, Reduced
6” 20” 1500# Flanged,RJ
Bore /W Gear
Operator
GA-15A41 (Wedge
1/2” 1 1/2” 1500# Flanged,RJ
Gate)
GA-15A42 (Wedge
2” 4” 1500# Flanged, RJ
Gate)
2” 4” 1500# Flanged, RJ GA-15A43(Flat Gate)
Gate Valve (Note 1)
GA-15A44 (Wedge
4” 20” 1500# Flanged,RJ Gate & /W Gear
Operator)
GA-15A45 (Flat Gate
4” 20” 1500# Flanged,RJ
& /W Gear Operator)
GL-15A41 (Spherical
1/2” 1 1/2” 1500# Flanged,RJ Disc& Renewable
Seat)
GL-15A42 (Spherical
2” 4” 1500# Flanged,RJ Disc & Renewable
Globe Valve Seat) (Note 1)

GL-15A43 (Spherical
Disc & Renewable
6” 16” 1500# Flanged,RJ
Seat With Gear
Operator)
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 69 OF 77

15A4
Piping Material Specification
(HOLD)
Service See Appendix A Corrosion Allowance 4 mm
Rating 1500 # PWHT Per B31.3 Piping Material C.S.

Allowable 25.5 MPa @ 0/38℃

Pressure 22.54 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
Check 1/2” 1 1/2” 1500# Flanged,RJ CK-15A41 (Lift)
(Note 1)
Valve 2” 20” 1500# Flanged,RJ CK-15A42 (Wafer)
1/2” 1 1/2” XXS BE Seamless, Steel Pipe
2” 4” SCH160 BE Seamless, Steel Pipe
6” 6” 15.88mm BE Seamless, Steel Pipe API 5L PSL2. Gr.BN,
Pipe
ASME B36.10M
8” 8” 19.05mm BE Seamless, Steel Pipe
10” 10” 22.23mm BE Seamless, Steel Pipe
12” 20” SCH120 BE Seamless, Steel Pipe
Seamless, Steel API 5L PSL2. Gr.BN,
Nipple 1/2” 1 1/2” XXS -
Pipe(80mm Long) ASME B36.10M
Elbow, Tee, Coupling, ASTM A105N,
1/2” 1 1/2” 9000# SW
Cap, Union ASME B16.11,
ASTM A105N,
Coupling, Cap, Union,
1/2” 1 1/2” 6000# NPTF ASME B16.11 &MSS
Threadolets
SP-97
ASTM A105N,
1/2” 1 1/2” 9000# SW Sockolets
MSS SP 97
1/2” 1 1/2” XXS BW
Fittings 2” 4” SCH160 BW
6” 6” 15.88mm BW ASTM A234 Gr.WPB
Elbow (LR) ,Tee ,Cap , Seamless
8” 8” 19.05mm BW Reducer
ASME B16.9
10” 10” 22.23mm BW
12” 20” SCH120 BW
1/2” 1 1/2” XXS BW
ASTM A105N,
2” 6” SCH160 BW Weldolets
MSS SP 97
8” 8” SCH140 BW
Flanges 1/2” 20” 1500# Flanged,RJ Welding Neck(Note 2) ASTM A105N,
1/2” 20” 1500# Flanged,RJ Blind ASME B16.5
1/2” 6” 1500# RJ Spectacle Blank ASTM A105N,
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 70 OF 77

15A4
Piping Material Specification
(HOLD)
Service See Appendix A Corrosion Allowance 4 mm
Rating 1500 # PWHT Per B31.3 Piping Material C.S.

Allowable 25.5 MPa @ 0/38℃

Pressure 22.54 MPa @ 148.9℃
Items Inch Size Rating End Tag No. & Main Material
From To Sch./Thk. Description
8” 20” 1500# RJ Blinds and Spacer ASME B16.48
Orifice Flange Set,
Orifice Flange Set, ASTM A694 F60,
2” 20” 1500# Flanged,RJ
0.5” socketweld taps ASME B16.36
(Note 2)
Stud Bolts, Alloy
Studs/ Full Length, /W Two Steel, ASTM A193-
1/2” 20” 1500# N/A HVY Hexagonal Nuts, B7 /194-2H, Hot Dip
Nuts ASME B 18.2.1/18.2.2 Galvanized ASTM
A153
304 SS, ASME B
Gasket 1/2” 20” 1500# N/A Oval Ring Type
16.20
Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 71 OF 77

15Q4
Piping Material Specification
(HOLD)
Service See Appendix A Corrosion Allowance 4 mm
Rating 1500 # PWHT Per CODE Piping Material C.S.

Allowable 25.5 MPa @ 0/38℃

Pressure 22.54 MPa @ 148.9℃
Inch Size Rating
Items End Tag No. & Description Main Material
From To Sch./Thk.
1/2” 1 1/2” SCH160 BE Seamless, Steel Pipe
Pipe 2” 8” SCH80 BE Seamless, Steel Pipe API 5L PSL2 X60,
10” 20” SCH60 BE Seamless, Steel Pipe ASME B36.10M

Seamless, Steel
Nipple 1/2” 1 1/2” SCH160 -
Pipe(80mm Long)
Elbow, Tee, Coupling, ASTM A694 F60,
1/2” 1 1/2” 9000# SW
Cap, Union ASME B16.11
ASTM A694 F60,
Coupling, Cap, Union,
1/2” 1 1/2” 6000# NPTF ASME B16.11
Threadolets
&MSS SP-97
ASTM A694 F60
1/2” 1 1/2” 9000# SW Sockolets
MSS SP 97
Fittings
1/2” 1 1/2” SCH160 BW Hot Bend Hot Bend
With 250mm tangent,
2” 8” SCH80 BW
Barred Tee, Reducer, API 5L.PSL2 X60
Cp,
10” 20” SCH60 BW
Isolation Joint
1/2” 1 1/2” SCH160 BW ASTM A694 F60
Weldolets MSS SP 97,
2” 8” SCH80 BW Seamless
1/2” 20” 1500# Flanged,RJ Welding Neck (Note 2) ASTM A694 F60,
1/2” 20” 1500# Flanged,RJ Blind ASME B16.5
1/2” 8” 1500# RJ Spectacle Blank ASTM A694 F60,
Flanges
10” 20” 1500# RJ Blinds and Spacer ASME B16.48
Orifice Flange Set (Note ASTM A694 F60,
2” 20” 1500# Flanged,RJ
2) ASME B16.36
Stud Bolts, Alloy
Studs/ Full Length, /W Two Steel, ASTM A193-
1/2” 20” 1500# N/A HVY Hexagonal Nuts B7 /194-2H, Hot Dip
Nuts ASME B 18.2.1/18.2.2 Galvanized ASTM
A153
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 72 OF 77

15Q4
Piping Material Specification
(HOLD)
Service See Appendix A Corrosion Allowance 4 mm
Rating 1500 # PWHT Per CODE Piping Material C.S.

Allowable 25.5 MPa @ 0/38℃

Pressure 22.54 MPa @ 148.9℃
Inch Size Rating
Items End Tag No. & Description Main Material
From To Sch./Thk.
304 SS, ASME B
Gasket 1/2” 20” 1500# N/A Oval Ring Type
16.20
Notes:
1. Valves selection please refers to piping class 15A4.
2. Thickness to suit pipe.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 73 OF 77

25D3
Piping Material Specification
(HOLD)
Service See Appendix A Corrosion Allowance 3 mm
Rating 2500 # PWHT YES Piping Material C.S. (NACE)

Allowable 42.5MPa @ 0/38℃

Pressure 37.5MPa @ 148.9℃
Inch Size Rating
Items End Tag No. & Description Main Material
From To Sch./Thk.
BA-25D31s (Trunnion
3 1/8” 3 1/8” 2500 # Flanged,RJ
Ball Mounted, Full Bore)
Ball Valve BA-25D32s (Trunnion (Note 1)
4 1/16” 4 1/16” 2500 # Flanged,RJ Mounted, Full Bore& /W
Gear Operator
3 1/8” 3 1/8” HOLD HOLD HOLD
Pipe API 6A
4 1/16” 4 1/16” HOLD HOLD HOLD
3 1/8” 3 1/8” HOLD HOLD HOLD
API 6A
Fittings
4 1/16” 4 1/16” HOLD HOLD
HOLD
3 1/8” 3 1/8” 2500 # Flanged,RJ HOLD(Note 2) API 6A
Flanges
4 1/16” 4 1/16” 2500 # Flanged,RJ HOLD(Note 2) API 6A
Studs/ 3 1/8” 3 1/8” 2500 # N/A HOLD
API 6A
Nuts 4 1/16” 4 1/16” 2500 # N/A HOLD
3 1/8” 3 1/8” 2500 # N/A HOLD
Gasket API 6A
4 1/16” 4 1/16” 2500 # N/A HOLD

Notes:
1. For details, see HFY-PIP-SP-00006 Specification for Valves.
2. Thickness to suit pipe.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 74 OF 77

APPENDIX C

BRANCH CONNECTIONS
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 75 OF 77

BRANCH CONNECTION TABLE 1

Piping class 1A1, 1A3, 1A4, 3A1, 6A1, 1U1, 6Q0, 15A4, 15Q4，
Branch Pipe
MainHeader 1/2 3/4 1 1 2 3 4 6 8 10 12 14 16 18 20 24
1/2
1/2 T
3/4 RT T
1 RT RT T
1 RT RT RT T
1/2
2 SO SO SO SO T
3 SO SO SO SO RT T
4 SO SO SO SO RT RT T
6 SO SO SO SO WO RT RT T
8 SO SO SO SO WO WO RT RT T
10 SO SO SO SO WO WO RT RT RT T
12 SO SO SO SO WO WO WO RT RT RT T
14 SO SO SO SO WO WO WO RT RT RT RT T
16 SO SO SO SO WO WO WO RT RT RT RT RT T
18 SO SO SO SO WO WO WO WO RT RT RT RT RT T
20 SO SO SO SO WO WO WO WO RT RT RT RT RT RT T
24 SO SO SO SO WO WO WO WO WO RT RT RT RT RT RT T
28 SO SO SO SO WO WO WO WO WO RT RT RT RT RT RT RT

Notes: T - Straight Tee

RT - Reducing Tee
SO - Sockolets
WO - Weldolets

1) Any deviation from the connection type shown in the above table or branch connections for
larger piping sizes shall be approved in writing by OWNER.
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 76 OF 77

BRANCH CONNECTION TABLE 2 –PIPING CLASS 1G0

BRANCH

inches 3/4 1 1 1/2 2 3 4

3/4 T
H 1 RT T
E
A 1 1/2 RT RT T
D
2 RT RT RT T
E
R 3 RT RT RT RT T

4 RT RT RT RT RT T

Notes: T - Straight Tee Screwed RTR - Tee with Reducer Screwed

RT- Reducing Tee Screwed
1) All branch connections shall be designed and reinforced so that the branch line connection is
equal to the pressure and temperature rating of the header.

2) Any deviation from the connection type shown in the above table or branch connections for
larger piping sizes shall be approved in writing by OWNER.

BRANCH CONNECTION TABLE 3 –

PIPING CLASS 1C0,3C0,6C0

BRANCH
inches 3/4 1 1 1/2 2 3 4 6

3/4 T

H 1 RT T

E 1 1/2 RT RT T

A 2 WO WO WO T

D 3 WO WO WO RT T

E 4 WO WO WO RT RT T

R 6 WO WO WO WO RT RT T
 HALFAYA PROJECT SURFACE FACILITY

Petrochina (Halfaya)

DETAIL DESIGN DOC. NO.: HFY-PIP-SP-00005 REV.: C. PAGE 77 OF 77

BRANCH CONNECTION TABLE 4

Piping class 3T1, 3D3, 1D3, 6D3, 3X3, 6X3, 25D3
Branch Pipe
MainHeader 1/2 3/4 1 1 2 3 4 6 8 10 12 14 16 18 20 24
1/2
1/2 T
3/4 RT T
1 RT RT T
1 RT RT RT T
1/2
2 WO WO WO WO T
3 WO WO WO WO RT T
4 WO WO WO WO RT RT T
6 WO WO WO WO WO RT RT T
8 WO WO WO WO WO WO RT RT T
10 WO WO WO WO WO WO RT RT RT T
12 WO WO WO WO WO WO WO RT RT RT T
14 WO WO WO WO WO WO WO RT RT RT RT T
16 WO WO WO WO WO WO WO RT RT RT RT RT T
18 WO WO WO WO WO WO WO WO RT RT RT RT RT T
20 WO WO WO WO WO WO WO WO RT RT RT RT RT RT T
24 WO WO WO WO WO WO WO WO WO RT RT RT RT RT RT T
28 WO WO WO WO WO WO WO WO WO RT RT RT RT RT RT RT