Atlas Copco Powercrusher

Technical specification PC 5

 PC 5

Specifications
Engine PC 5 (metric) PC 5 (imperial)
Engine make CAT
Engine model C13 Tier 4i (C13 Tier 3)
Engine power 328 kW (328 kW) 440 HP (440 HP)
Engine type 4 cycle, water cooled, direct injection
Air cleaner CAT pre cleaner
Emission certification EPA Tier 4i (Tier 3)
Hydraulic system
Hydraulic type Open circuit
Hydraulic pump Radial piston pump
Cooler and max ambient temp (celcius) Combi Cooler - 50 degrees C
Electrical system
Voltage 24V DC
Batteries 2 x 12V 180 Ah
Alternator CAT 24V 95A (CAT 24V 65A Tier 3)
Undercarriage
Track adjuster Hydraulic
Number of shoes each side 55
Number of track rollers 10 +10
Wheel base 3 782 mm 12' 4"
Track width (inside/outside) 1 960 / 2 960 mm 6' 5" / 9' 8"
Track chain width 500 mm 20"
Travel speeds 1.10-1.90 km/h 0.7-1.2 mph
Max. travel speed (KPH) 1.90 km/h 1.2 mph
Hill climbing ability (degrees) 25.8°
Crusher
Crusher box weight 14 800 kg 32 628 lbs
Inlet opening 1 250 x 1 020 mm 49" x 40"
Outlet to conveyor belt dimension 1 040 mm 41"
Hammer data 360 kg 794 lbs
Gap setting range CSS lower beam* 30 - 130 mm 1 ¼" - 5.2"
Rotor revolution 710 at max engine rpm
Rotor width 1 200 mm 48"
Rotor diameter 1 300 mm 51"
Number of V-belts and specification 8 x KRN9000SPC
Setting adjustment Hydraulic assist with shim plates
Drive type Over KPTO-19 trans. with V-belts
Feedhopper
Charging volume 9.5 m3 12.4y3
Charging height 4 000 mm 13' 1"
Charging w idth 2 920 mm 9' 7"
Charging length 4 325 mm 14' 2"

* To be read in conjunction with operating manual

2 
PC 5

Specifications
Vibrating feeder with pre-screen section PC 5 (metric) PC 5 (imperial)
Length 4 790 mm 15' 8"
Width 1 162 mm 45"
Grid openings 25-40 mm straight 1-1 ½" straight
Grid dimensions L / W 1 800 x 1 140 mm 71" x 45"
Double deck ( YES / NO ) YES
Lower deck mesh size 25 mm 1"
Vibro drive type and displacement (cc) Hydraulic motor - 50cc
Indep double deck pre-screen drive and
Hydraulic motor - 55cc
displacement (cc)
Main conveyor
Main conveyor width and length 1 200 / 20 450 mm 48" / 67'
EP500/3 10+3 seamless 19mm THK
Belt specification
steel reinforced
Main conveyor discharge height 3 304 mm 10' 10"
Drive drum diameter Ø392 mm Ø15"
Belt speed 1.7 m/s 5.5 ft/s
Drive type and displacement (cc) Hydraulic motor - 750cc
Side conveyor
Side conveyor width and length 800 / 10 350 mm 31" / 33' 11"
Side conveyor discharge height 2 869 mm 9' 5"
Drive drum diameter Ø254 mm Ø10"
Belt speed 2.73 m/s 9 ft/s
Drive type and displacement (cc) Hydraulic motor - 315cc
Magnetic seperator
Magnetic separator make Eriez UK
Type Permanent
Belt width 750 mm 29"
Dimensions
Operation length 14 616 mm 47' 11"
Opeartion height 4 650 mm 15' 3"
Operation width 5 786 mm 18' 11"
Transport length 14 620 mm 47' 11"
Transport height 3 650 mm 11' 11"
Transport width 2 980 mm 9' 9"
Length of track on ground 3 782 mm 12' 4"
Ground clearance 307 mm 12"
Weight
Total weight 53 000 kg 116 845 lbs
Ground pressure 1.37 bar 19.8 lb/sq inch
Volumes
Refill capacity - coolant 39 ltr 10 gallon
Refill capacity - fuel tank 900 ltr 238 gallon
Refill capacity - engine 35 ltr 9 gallon
Refill capacity - hydraulics 850 ltr 225 gallon
Refill capacity - clutch 40 ltr 10 gallon
Refill capacity - transmission distribution N/A
Refill capacity - final drives, each 18 ltr 5 gallon
Refill capacity - vibrating hopper 4 ltr 1 gallon

3 
 PC 5

hopper
vibrating
adjusable
Hydraulically

hopper
Wear resistent

tubes
section
Independent

Fixed hydraulic
double deck pre-screen
Product features
Transport dimensions

at outlet
conveyor

Impact plates
under conveyor
foldable side
Hydraulically
beams
14620

Hydraulically
adjustable swing

belt
(C13 T3)
drive unit
CAT C13 T4

Large distance
between crusher
outlet and conveyor
belt
Lowerable
main conveyor

Large GRP covers

magnetic
separator
Permanent
2980

main conveyor
HS1 screenbox
can be mounted on
belt
19 mm (3/4")
steel reinforced
3650

9851 2873 01 2012-01 Örebro, Sweden Legal Notice © Copyright 2012, Atlas Copco Rock Drills AB, Örebro, Sweden. All product names in this publication are trademarks of Atlas Copco. Any unauthorized use or copying of the contents or any part thereof is prohibited. Illustrations and photos
may show equipment with optional extras. No warranty is made regarding specifications or otherwise. Specifications and equipment are subject to change without notice. Consult your Atlas Copco Customer Center for specific information.