8/9/2020 Exhaust Camshaft and Lifter Replacement (Camshaft) - ALLDATA Repair
2007 Pontiac G5 L4-2.4L
Vehicle > Engine, Cooling and Exhaust > Engine > Camshaft, Lifters and Push Rods > Camshaft > Service and Repair
> Removal and Replacement
EXHAUST CAMSHAFT AND LIFTER REPLACEMENT
Exhaust Camshaft and Lifter Replacement
Removal Procedure
1. Remove the exhaust camshaft position actuator.
Important: Remove each bolt on each cap one turn at a time until there is no spring tension pushing on the
camshaft.
2. Mark the bearing caps to ensure they are installed in the original position.
3. Remove the bearing cap bolts.
4. Remove the bearing caps.
https://my.alldata.com/repair/#/repair/article/43179/component/56/itype/401/nonstandard/1268925/selfRefLink/false 1/9
8/9/2020 Exhaust Camshaft and Lifter Replacement (Camshaft) - ALLDATA Repair
5. Remove the exhaust camshaft (3).
https://my.alldata.com/repair/#/repair/article/43179/component/56/itype/401/nonstandard/1268925/selfRefLink/false 2/9
8/9/2020 Exhaust Camshaft and Lifter Replacement (Camshaft) - ALLDATA Repair
Important: Keep all of the roller followers and hydraulic adjusters in order so that they can be reinstalled in their
respective locations.
6. Remove the camshaft roller followers.
https://my.alldata.com/repair/#/repair/article/43179/component/56/itype/401/nonstandard/1268925/selfRefLink/false 3/9
8/9/2020 Exhaust Camshaft and Lifter Replacement (Camshaft) - ALLDATA Repair
7. Remove the hydraulic element lash adjusters.
Installation Procedure
https://my.alldata.com/repair/#/repair/article/43179/component/56/itype/401/nonstandard/1268925/selfRefLink/false 4/9
8/9/2020 Exhaust Camshaft and Lifter Replacement (Camshaft) - ALLDATA Repair
1. Install the hydraulic element lash adjusters into their bores in the cylinder head.
2. Lubricate the hydraulic lash adjusters with GM PN 12345501 (Canadian PN 992704) or equivalent.
https://my.alldata.com/repair/#/repair/article/43179/component/56/itype/401/nonstandard/1268925/selfRefLink/false 5/9
8/9/2020 Exhaust Camshaft and Lifter Replacement (Camshaft) - ALLDATA Repair
3. Lubricate the valve tips with GM PN 12345501 (Canadian PN 992704) or equivalent.
https://my.alldata.com/repair/#/repair/article/43179/component/56/itype/401/nonstandard/1268925/selfRefLink/false 6/9
8/9/2020 Exhaust Camshaft and Lifter Replacement (Camshaft) - ALLDATA Repair
Important: Used roller followers MUST be returned to the original position on the camshaft. If the camshaft is
being replaced, the roller followers actuated by the camshaft must also be replaced.
4. Position the roller followers on the tip of the valve stem and on the lash adjuster. Apply lubricate GM PN
12345501 (Canadian PN 992704) or equivalent.
https://my.alldata.com/repair/#/repair/article/43179/component/56/itype/401/nonstandard/1268925/selfRefLink/false 7/9
8/9/2020 Exhaust Camshaft and Lifter Replacement (Camshaft) - ALLDATA Repair
5. Install the exhaust camshaft (3). Lubricate with GM PN 12345501 (Canadian PN 992704) or equivalent.
6. Install the camshaft bearing caps. Hand tighten the cap bolts.
Notice: Refer to Fastener Notice.
https://my.alldata.com/repair/#/repair/article/43179/component/56/itype/401/nonstandard/1268925/selfRefLink/false 8/9
8/9/2020 Exhaust Camshaft and Lifter Replacement (Camshaft) - ALLDATA Repair
7. Tighten the bearing cap bolts in increments of 3 turns until they are seated.
Tighten the bolts to 10 N.m (89 lb in).
8. Install the exhaust camshaft position actuator.
https://my.alldata.com/repair/#/repair/article/43179/component/56/itype/401/nonstandard/1268925/selfRefLink/false 9/9
