Scribd
Upload
225 views

TS and CG Terminal Circuit

Uploaded by

Yomar Negron
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
225 views

TS and CG Terminal Circuit

Uploaded by

Yomar Negron
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Inspection Procedure - Toyota Service Information 11/3/17, 9(27 pm

Print Exit

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS ANTI-LOCK BRAKE SYSTEM TS and CG Terminal
Circuit

DESCRIPTION

In Test Mode (signal check), a malfunction in the speed sensor that cannot be detected when the vehicle is
stopped can be detected while driving.
Sensor check mode can be entered by connecting terminals TS and CG of the DLC3 and turning the ignition switch
from off to ON.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
When replacing the skid control ECU (brake actuator assembly), perform Test Mode (Signal Check) to acquire
the rear differential lock identification information.
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>TEST MODE
PROCEDURE

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TS of DLC3)

a. Turn the ignition switch off.

b. Disconnect the A3 skid control ECU (brake actuator assembly) connector.

c. Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Specified
Condition
Connection Condition

https://toyotamanuals.com.au/docs/hilux-service-repair-manua…/RM100000000L25V.html?PUB_TYPE=RM&MODE=3#RM100000000L25V_05 Page 1 of 3
Inspection Procedure - Toyota Service Information 11/3/17, 9(27 pm

A3-32 (TS) -
Always Below 1 Ω
G8-12 (TS)
A3-32 (TS) or
10 kΩ or
G8-12 (TS) - Always
higher
Body ground

Result:
Proceed to
OK
NG

OK

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

a.

*a Front view of DLC3

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Specified
Condition
Connection Condition
G8-4 (CG) -
Always Below 1 Ω
Body ground

Result:
Proceed to
OK
NG

OK

https://toyotamanuals.com.au/docs/hilux-service-repair-manua…/RM100000000L25V.html?PUB_TYPE=RM&MODE=3#RM100000000L25V_05 Page 2 of 3
Inspection Procedure - Toyota Service Information 11/3/17, 9(27 pm

REPLACE BRAKE ACTUATOR ASSEMBLY

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR(w/o


VSC)>REMOVAL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

© 2012 TOYOTA MOTOR CORPORATION. All Rights Reserved.

https://toyotamanuals.com.au/docs/hilux-service-repair-manua…/RM100000000L25V.html?PUB_TYPE=RM&MODE=3#RM100000000L25V_05 Page 3 of 3

You might also like