General AI-517-02

Specifications
GS48C17Z02-00E-N Analogue Input Module (open < 2.8 mA)

■ GENERAL Figure 1

This Analogue Input module, or trip

amplifier, contains two circuits and
can be utilized for various
applications.

The open line detection level is

configured for 2.8 mA.

AI-517-02
Analogue Input Module (open < 2.8 mA)

This module has a number of typical characteristics:

• Galvanic isolation between inputs and between inputs and logic

• Supply for passive transmitters
• Current or voltage input
• Internal or external set point setting with set point limiter
• LED indication
• Transmitter and set point outputs
• Open line input detection
• Normal or inverting operation
• Shift register circuit for connection to the Sequence of Event Recording system (SER)

The incoming field current signal is converted to a voltage signal. This signal (or a voltage input signal) is
internally compared with the set point and open line levels. The result of comparison with the set point is
used for the circuit output. Depending on the wiring, the output is a high or a low trip signal.

The result of the open line comparison can be used to disable the output in case of a line fault. Open line
levels are set by resistors on the module.

Both set point and field input signals are available for monitoring as a 0 - 10 V signal.

GS48C17Z02-00E-N
Yokogawa Europe B.V.  Copyright 2017
1st Edition January 2017
AI-517-02 2 of 8

■ FUNCTIONAL DIAGRAM

Inputs Module Outputs

Supply Notes Front

z32 24 Vdc field The output LEDs 3 and 6 represents the output current. 1 set point circuit 1
z30 0 Vdc field 2 test bus / led 1
b32 20 Vdc logic Disabling LEDs for unused circuits: 3 test bus / led 2
d32 0 Vdc logic connect b04-b08 (b18-b22) for LED 1(4) 4 test bus / led 3
d30 A voltage pulse connect b02-z06 (b16-z22) for LED 2(5) 5 set point circuit 2
b30 not used 6 test bus / led 4
7 test bus / led 5
8 test bus / led 6

All Rights Reserved.  Copyright Yokogawa Europe B.V. GS48C17Z02-00E-N January 2017
AI-517-02 3 of 8

■ SPECIFICATIONS

Description Data
General Number of channels 2
Width 3HP
Identification AI-517 on front and more detailed on connector label
Weight 130 gram

Input Current input 0 - 20 mA, 55 Ω ± 10% (60 mA max., fuse protected)

Voltage input 0 - 10 V, 1 MΩ (max. 30 V)
Voltage output 0 - 10 V ± 0.5%, max. 5 mA
Open line level 2.8 mA ± 0.4 mA
Open line indication Below open line level: red LED
Reference output 11.25V±1%, 5 mA max.
Set point input 10 kΩ (30 V max.)
Set point level Adjustable by potentiometer
Trip indication Above set point : red LED
Hysteresis 1% (full scale, trip & open line)
Stability error < 0.2% (full temp. range)
Clock Clock pulses from MC-573, level 0 / 11 V

Output Pulse logic Current pulses 500 mA

Capacity 10 unit loads
Status indication Red LED per output
Monitor 0 - 10 V, 1 kΩ
Test bus 0 - 10 V, 10 kΩ (0 Ω for 0 V test bus)
Transmitter supply 25.5 Vdc ± 0.5 V (at 2 x 20 mA) and field voltage tolerance,
80 mA max. / channel (fuse protected)
Data 8 bits serial data, level 0 / 11 V

Propagation RC-filtering 50 msec.

Supply Field supply 24 Vdc ± 10%

35 - 50 mA passive
40 - 100 mA active
Logic supply 20 Vdc
5 mA
Clock A pulse, level 0 / 20 V

Dissipation Passive 1.0 - 1.3 W

Active 1.1 - 1.6 W

Signal definition: 0 – 100% = 0 - 20 mA = 0 - 10 V (max. signal: 120%)

All Rights Reserved.  Copyright Yokogawa Europe B.V. GS48C17Z02-00E-N January 2017
AI-517-02 4 of 8

■ NOTES

Input & Setpoint configurations

External AI-517 AI-517 AI-517
power supply d08 +24V
d08 +24V
d08 +24V
d10 20µA d10 20µA d10 20µA
Connect for high trip
at open transmitter
b06 b06 line. b06
0-20mA
b04 + 0-20mA b04 0-10V b04
+ d04 d04 + d04
d06 + I d06 + I d06 + I
z06 0 U z06 0 U z06 0 U

Current input Current input Voltage input

Active transmitter Passive transmitter Active transmitter
Active transmitter (with external power supply) Passive transmitter (powered by AI-517) Active transmitter (with external power supply)
Passive AI-517 Active AI-517 Passive AI-517

AI-517 AI-517
d08 +24V
d08 +24V
d10 20µA d10 20µA

b06 b06
+ 0-20mA b04 AI-517 + 0-20mA b04 AI-517
d08 d08
d04 +24V d04 +24V
d10 d10
d06 + I 20µA d06 + I 20µA

z06 0 U z06 0 U
b06 b06
b04 0-10V b04
d04 d04
0-20mA d06 + I d06 + I
z06 0 U 0V-common z06 0 U

Current input, passive transmitter Current input, passive transmitter

2 Channels serial connected 2 Channels parallel connected
Passive transmitter (powered by AI-517) Passive transmitter (powered by AI-517)
Active AI-517 (first AI-517 active, second AI-517 passive) Active AI-517 (first AI-517 active, second AI-517 passive voltage input)
No galvanic isolation between channels No galvanic isolation between channels

AI-517 AI-517 AI-517

b08 Uref
b08 Uref

b10 Setpoint 0-10V b10 Setpoint

d04 0 d04 d04 0

d06 + I 0-20mA d06 + I 0-20mA d06 + I

z06 0 U 0V-common
z06 0 U 0V-common
z06 0 U

Internal Setpoint reference

External Setpoint reference
Adjust Setpoint with multiturn potentiometer at module front panel
Clockwise is up, counter clockwise is down Example for comparing 2 analog signals
No galvanic isolation between channels

All Rights Reserved.  Copyright Yokogawa Europe B.V. GS48C17Z02-00E-N January 2017
AI-517-02 5 of 8

■ NOTES

All Rights Reserved.  Copyright Yokogawa Europe B.V. GS48C17Z02-00E-N January 2017
AI-517-02 6 of 8

■ NOTES

All Rights Reserved.  Copyright Yokogawa Europe B.V. GS48C17Z02-00E-N January 2017
AI-517-02 7 of 8

■ NOTES

All Rights Reserved.  Copyright Yokogawa Europe B.V. GS48C17Z02-00E-N January 2017
AI-517-02 8 of 8

■ NOTES

All Rights Reserved.  Copyright Yokogawa Europe B.V. GS48C17Z02-00E-N January 2017