Scribd
Upload
443 views1 page

General Notes: Legends: Riser Diagram:: Service Entrance

The document provides general notes for electrical works including wiring methods, materials, and mounting heights. The electrical service is 1-phase, 2-wire, 230V AC, 60Hz. Wiring methods include intermediate metallic conduit for feeders and risers and PVC conduit for lighting and power receptacles. Grounding is required for all lighting and power circuits per code.

Uploaded by

Jonard Meregildo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
443 views1 page

General Notes: Legends: Riser Diagram:: Service Entrance

The document provides general notes for electrical works including wiring methods, materials, and mounting heights. The electrical service is 1-phase, 2-wire, 230V AC, 60Hz. Wiring methods include intermediate metallic conduit for feeders and risers and PVC conduit for lighting and power receptacles. Grounding is required for all lighting and power circuits per code.

Uploaded by

Jonard Meregildo
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 1

GENERAL NOTES: LEGENDS:

1. ALL ELECTRICAL WORKS SHALL COMPLY IN ACCORDANCE WITH THESE LIGHTING OUTLET
RISER DIAGRAM:
PLANS AND SPECIFICATIONS. THE APPLICABLE PROVISIONS OF THE LATEST
EDITION OF THE PHILIPPINE ELECTRICAL CODE (PEC). THE RULES AND DUPLEX CONVENIENCE OUTLET
REGULATION OF THE LOCAL ENFORCING AUTHORITY AND THE
REQUIREMENTS OF THE LOCAL POWER COMPANY. THE ELECTRICAL WORKS W
SHALL BE DONE UNDER THE IMMEDIATE SUPERVISION OF A DULY
WASHING MACHINE OUTLET
REGISTERED ELECTRICAL ENGINEER.
R

2. THE ELECTRICAL SERVICE POWER IS 1-PHASE, 2-WIRE, 230 V AC, 60 Hz. RANGE AND RANGE HOOD
RH SERVICE ENTRANCE

GFCI
3. WIRING METHOD SHALL BE AS FOLLOWS : 230V, 1Ø, 2
a. FEEDERS AND RISERS - INTERMEDIATE METALLIC CONDUIT GFCI CONVENIENCE OUTLET WIRE, 60Hz
b. LIGHTING, POWER RECEPTACLE - POLYVINYL CHLORIDE
CONDUIT SCH. 40 BRANCH CKT., & AUXILIARY
ACU OUTLET PROVISION
ACU
2 - 22 sq. mm THW
4.ALL WIRES SHALL BE COPPER AND THERMOPLASTIC INSULATED TYPE
"THW" UNLESS OTHERWISE INDICATED IN THE PLAN. THE MINIMUM SIZE OF Sa ONE GANG SWITCH
WIRE FOR POWER AND LIGHTING CIRCUIT HOMERUN SHALL BE 3.5mm² AND
INSULATED FOR 600 VOLTS. SMALLEST RACEWAY SHALL BE 15mmØ Sab TWO GANG SWITCH
TRADE/NOMINAL SIZE.
100
5. ALL OUTLET BOXES SHALL BE GALVANIZED GAGE NO. 16 DEEP TYPE WITH PANEL BOARD
FACTORY
KNOCKOUTS.
LP
1 HOMERUN 1 2
20 20
6. ALL MATERIALS TO BE USED SHALL BE BRAND NEW AND APPROVED TYPE
FOR THE
RACEWAY CONDUIT CONCEALED UNDER FLOOR
PARTICULAR LOCATION AND PURPOSE OF USAGE.
3 20 4 30
7. GROUNDING SYSTEM SHALL BE PROVIDED TO ALL LIGHTING AND POWER RACEWAY CONDUIT CONCEALED UNDER CEILING
CIRCUIT AS
PER PHILIPPINE ELECTRICAL CODE REQUIREMENT.
5 30 6 20
8. MOUNTING HEIGHT OF WIRING DEVICES SHALL BE AS FOLLOWS : CIRCUIT BREAKER

a. LIGHT SWITCH - 1.2 M ABOVE FINISH FLOOR


7 20
b. CONVENIENCE OUTLET - 0.3 M ABOVE FINISH FLOOR SERVICE ENTRANCE

c. PANEL BOARD -1.5 M ABOVE FINISH FLOOR

GROUND TERMINAL
#8 sq. mm BARE COPPER
LOAD SCHEDULE

You might also like