wear parts catalog Doc. no. R 223.

1330

SANDVIK CS660:01
This document is valid for:

Serial no. / Machine no. Sign.

SANDVIK CS660:01

© Copyright 2007 Sandvik SRP AB.

All rights reserved. No parts of this document may be reproduced or copied in any form or by
any means without written permission from Sandvik SRP AB. All data and information in this
manual may be changed without further notice. Reservations for misprints.

Document number: R 223.1330

Issue: 20080814
Version: 1

Sandvik
Stationsplan, SE-233 81 Svedala, Sweden
Tel: +46 (0)40 409000, Fax: +46 (0)40 409260
www.sandvik.com
WPC Sandvik CS660:01

General
Ordering information
When ordering parts, always state the machine type, manufacturing number,
serial number and order number according to the identification plate on the
cone crusher or tank. State quantity, article number and denomination for
each ordered part. The quantities listed in this catalog show how many pieces
of each part that are usually exchanged in a certain position.
Crusher’s identification plate
The figure below shows an example of the crusher’s identification plate. The
identification plate contains data needed when contacting Sandvik
concerning wear parts.
Please enter the serial number of the associated machine in the intended field
on the first page of this wear part catalog (the copyright page).

1 2 3 4

Identification plate:
1 Machine type
2 Part number
3 Serial number
4 Order number

The “Type” number is a designation system that describes the product.

Type:
1 Type and size of crusher
2 Crushing chamber (concave ring) CS660-EC/B-25/30/36/20:1
3 Mantle
4 Filler ring
1 2 4 5
5 Eccentric throw (mm)
6 Mark number 3

© 2007 Sandvik SRP AB Doc. no. R 223.1330 Ver. 1 3

WPC Sandvik CS660:01

Tank unit identification

The figure below shows an example of the tank unit’s identification plate.
The identification plate contains data needed when contacting
Sandvik SRP AB concerning this specific equipment

Identification plate:
1 Type
2 Part number
3 Serial number
4 Order number

1 2 3 4

Think ahead!
Avoid unnecessary downtime and increased freight charges by ordering parts
well in advance.
Feedback
If you have comments on this wear parts catalog or problems connected to
the crusher’s documentation, send an e-mail to: [email protected]

4 Doc. no. R 223.1330 Ver. 1 © 2007 Sandvik SRP AB

WPC Sandvik CS660:01

Overview with section number references

Cone crusher 2
Feed hopper
5
3

5 1

7
6
Over-pressure system

11
8 9

1 Feed hopper Tank unit

2 Spider cap
3 Head nut
4 Liners
5 Liner and Air filter
6 Dust sealing
7 Bottomshell wearing
8 Step bearing set
9 Chevron packing
10 Hydroset 10
11 Over-pressure system
12 Tool list

© 2007 Sandvik SRP AB Doc. no. R 223.1330 Ver. 1 5

WPC Sandvik CS660:01

1. Feed hopper
1

2
4
5
3

Pos no Qty. Part number Alternative Description Remarks

1 442.9120-00 Feed hopper complete Consist of:
1 1 442.8978-00 Feed hopper
2 12 840.0532-00 Screw M6S 20x110 8.8 ISO 4014
3 12 845.0203-00 Nut M20 20 8 ISO 7040
4 12 847.0132-00 Washer BRB 21x36 HB 200
5 12 847.0197-00 Washer TBRSB 21x52 1370

2. Spider cap
5150-0 5155-0 5685-0, -2 5675-0 5651-0

5705-0

5655-0,
5650-0 5655-2

Cat. no. Qty. Part number Alternative Description Remarks

5150-0 2 442.8976-01 Arm shield
5650-0 1 442.8753-01 Spider cap
5655-0 6 840.0652-00 Screw M6S 20x90 8.8 ISO 4017
5655-2 4 847.0132-00 Washer TBRB 21x36 HB200 SS 3576
5651-0 1 873.1160-00 Seals O-ring 529,3x5,7 SMS 1586
5675-0 1 442.8754-01 Spider bushing
5685-0 6 840.0652-00 Screw M6S 20x90 8.8 ISO 4017
5685-2 6 847.0132-00 Washer BRB 21x36 HB200 SS 3576
5705-0 1 442.8755-01 Oil seal ring

6 Doc. no. R 223.1330 Ver. 1 © 2007 Sandvik SRP AB

WPC Sandvik CS660:01

3. Head nut

4205-0

4025-0 4205-2

4205-1

Cat. no. Qty. Part number Alternative Description Remarks

4025-0 1 442.8792-01 Main shaft sleeve
4205-0 1 442.8800-00 Head nut with burning ring
4205-1 1 442.8791-01 Inner head nut
4205-2 1 452.0269-001 Burn ring

© 2007 Sandvik SRP AB Doc. no. R 223.1330 Ver. 1 7

WPC Sandvik CS660:01

4. Liners

6390-0

6305-0

4175-0

Cat. no. Qty. Part number Alternative Description Remarks

6395-9 831-0016-00 Casting compound
6390-0 1 442.8981-00 Concave upper EC Extra coarse
442.9072-00 -90 Concave upper C Coarse
6305-0 442.8979-00 -90 Concave lower EC Extra coarse
442.9071-00 -90 Concave lower C Coarse
4175-0 1 442.8982-01 -02 Mantle A
442.8983-01 -02 Mantle B

8 Doc. no. R 223.1330 Ver. 1 © 2007 Sandvik SRP AB

WPC Sandvik CS660:01

The table below illustrates different crushing chambers alternatives

Crushing chamber(se page 3 Type number)

CS660-EC/B-25/30/36/20:1

6390-0 6305-0 6395-9 4175-0 4175-9

Concave upper Concave lower Casting Mantle Casting
Comp. Comp.

EC extra coarse EC extra coarse Total A 4x10 kg

EC/A 442.8981-00 (M1) 442.8979-00 (M1) 6390-0 and 6305-0 442.8982-01 (M1)
442.8979-90 (M2) =20x10 kg 442.8982-02 (M2)
EC extra coarse EC extra coarse Total B 4x10 kg
EC/B 442.8981-00 (M1) 442.8979-00 (M1) 6390-0 and 6305-0 442.8983-01 (M1)
442.8979-90 (M2) =20x10 kg
C course C coarse Total A 4x10 kg
C/A 442.9072-00 (M1) 442.9071-00 (M1) 6390-0 and 6305-0 442.8982-01 (M1)
442.9072-90 (M2) 442.9071-90 (M2) =46x10 kg 442.8982-02 (M2)
C course C coarse Total B 4x10 kg
C/B 442.9072-00 (M1) 442.9071-00 (M1) 6390-0 and 6305-0 442.8983-01 (M1)
442.9072-90 (M2) 442.9071-90 (M2) =46x10 kg

5. Liner and Air filter

5110-0

5650-1

5650-3

Cat. no. Qty. Part number Alternative Description Remarks

(5650-1) 1 912.0155-00 Filter cartridge 852.514 Mic
5650-1 1 912.0114-00 Air filter P 10102 R 1/4”
5650-2 1 900.0243-00 Wrought iron pipe fittings socket Rp 1/4

© 2007 Sandvik SRP AB Doc. no. R 223.1330 Ver. 1 9

WPC Sandvik CS660:01

6. Dust sealing

4305-0
4350-0
4355-1

4365-1 4365-0,-2
4355-0
Cat. no. Qty. Part number Alternative Description Remarks
4305-0 1 442.8802-01 Dust seal ring
4350-0 1 442.8801-01 Retaining ring
4355-0 1 442.8804-01 Retainer
4355-1 1 442.8805-01 Scraper
4365-0 11 840.0069-00 Screw M6S 16x55 8.8 ISO 4017 Fasteners for dust sealing and scraper
4365-1 1 840.0071-00 Screw M6S 16x65 8.8 ISO 4014
4365-2 12 847.0016-00 Washer BRB 17x30 HB200 ISO 7089

8. Bottomshell wearing liners

1010-2
1320-2 1320-3

1320-4 1320-4

1320-2

1320-3
1320-4 1320-1 1010-1
Cat. no. Qty. Part number Alternative Description Remarks
1010-1 1 442.8760-00 Liner-Pin shaft arm Arm liners
1010-2 2 442.8759-01 Liner-Narrow arm
1320-1 1 442.9040-01 Wearing plate
1320-2 2 442.9041-01 Wearing plate
1320-3 2 442.9042-01 Wearing plate
1320-4 7 442.9043-01 Wearing plate
12 804.0004-00 Rod 1312-00 4-kt 12 L=60
8 847.0059-00 Washer TBRSB 13,5x36 1370
2 840.0049-00 Screw M6S 12x40 8.8 ISO 4014

10 Doc. no. R 223.1330 Ver. 1 © 2007 Sandvik SRP AB

WPC Sandvik CS660:01

9. Step bearing set

4075-0

2280-0

2260-0

Cat. no. Qty. Part number Alternative Description Remarks

4075-0 1 442.8732-01 Main shaft step
2280-0 1 442.8731-01 Step washer
2260-0 1 442.8730-01 Piston wearing plate

10. Chevron packing

2401-1 2305-0

2540-0 2540-1 2055-0, -2

Cat. no. Qty. Part number Alternative Description Remarks
2055-0 1 840.0019-00 Screw MC6S 8x12 8.8
2055-2 1 847.0012-00 Washer BRB 8,4x16 HB200 ISO 7089
2305-0 1 442.8739-00 Chevron packing
2401-0 1 841.0266-00 Screw MC6S 12x25 8.8
2540-0 1 873.0838-00 Seals O-ring 499,3x5,7 SMS 1586
2540-1 1 873.1277-00 Seal O-ring 548,0x5,7 SMS 1586

© 2007 Sandvik SRP AB Doc. no. R 223.1330 Ver. 1 11

WPC Sandvik CS660:01

11. Hydroset

3
1
2

Cat. no. Qty. Part number Alternative Description Remarks

1 1 912.0129-00 Filter cartridge HC2 Pinionshaft lubrication system
2 4 912.0126-00 Filter cartridge HC69 Main lubrication system
3 1 912.0129-00 Filter cartridge HC2 Hydroset oil system
4 2 873.0643-00 O-ring

12. Over-pressure system

1

Cat. no. Qty. Part number Alternative Description Remarks

1 1 912.0139-00 Filter cartridge 852516 Mic

12 Doc. no. R 223.1330 Ver. 1 © 2007 Sandvik SRP AB

WPC Sandvik CS660:01

13 Tool list
Cat. no. Qty. Part number Alternative Description Remarks
442.8877-90 Tool box complete
1 442.8879-00 Lifting tool Eccentric sleeve
1 442.8880-00 Lifting tool Bottom shell bushing
3 843.1511-00 Lowering rod M24x750 Removal of piston
3 845.0012-00 Nut M6M M24 8 Lowering rod
1 442.7284-00 Lowering rod M16x600 Removal of main shaft step
1 442.9996-00 Piston stop plate Holding piston
1 840.0542-00 Screw M6S 24x75 For piston stop plate
1 442.7282-01 Eye bolt Remove plate, piston
1 899.0331-00 Eye bolt Mainshaft
4 899.0299-00 Eye bolt Top shell
3 899.0160-00 Eye bolt LT M20 Spider bushing
4 899.0147-00 Eye bolt LT M16 Dust, collar, piston
4 899.0155-00 Eye bolt LT M12 Eccentric unit
2 899.0244-00 Eye bolt LT M8 Mainshaft sleeve
1 920.0110-00 Ring spanner striking NV 65 mm Screw & nut M42
1 920.0151-00 Ring spanner striking NV 36 mm Screw & nut M24
1 920.0131-00 U-ring spanner NV 46 mm Screw & nut M30
1 920.0135-00 U-ring spanner NV 36 mm Screw & nut M24
1 920.0134-00 U-ring spanner NV 30 mm Screw & nut M20
1 920.0022-00 U-ring spanner NV 24 mm Screw & nut M16
1 920.0245-00 U-ring spanner NV 16 mm Screw & nut M10
1 920.0186-00 U-ring spanner NV 13 mm Screw & nut M8
1 920.0041-00 Socket screw key NV 17 Screw MC6S 20
1 920.0038-00 Socket screw key NV 10 Screw MC6S 12
1 920.0037-00 Socket screw key NV 8 Screw MC6S 10
1 920.0035-00 Socket screw key NV 5 Air bleeder valve
1 920.0032-00 Socket screw key 5/8” Plug Spider Cap
1 923.0422-00 Feeler gauge 0,05-1 mm L=300

© 2007 Sandvik SRP AB Doc. no. R 223.1330 Ver. 1 13

WPC Sandvik CS660:01

This page is intentionally left blank

14 Doc. no. R 223.1330 Ver. 1 © 2007 Sandvik SRP AB