HPR-2 Series

Electrically Heated Regulators

Introduction
The HPR-2 Series heated pressure regulator
is designed to supply heat to samples
entering instrumentation systems. It can
be used to preheat liquids, to prevent
condensation of gases or to vaporize
liquids prior to gas analysis.
The modular design of the
HPR-2 consists of heat exchanger
and pressure control sections.
The pressure control section is
patterned after the time proven
design of the PR-1 pressure
reducing regulator and provides

pressure regulators
the same excellent outlet
pressure stability. The heat
exchanger section is made up of a
body and heat exchange element.
The heat exchange element uses
GO Regulator’s unique spiral
wrapped screen as the heat exchange surface. This screen has up to 100 square inches of heat transfer area and
precise design forces all sample flow to pass through the element.
The HPR-2 Series of vaporizing pressure reducing regulators are both CSA and ATEX approved. The electrical
components of this unit are securely housed in a Class A, B, C, D condulet assuring that there is always an
adequate flame path between the environment and the controller. Safety considerations can be further
enhanced by using the optional TCO (Thermal Cut Out) heater cartridge and proportional controller. These
features enable the unit to boast a T3 rating with 150 watts of power.

Typical Applications Features & Benefits

Analytical process sample conditioning systems: • Optional Hastelloy® C and Monel®
• Petrochemical refineries • Electropolished body with better than 25 Ra finish
• Chemical production facilities in diaphragm cavity for an optimal sealing surface
• Pilot plants (chemical & petrochemical) • Bubble-tight shutoff
• LNG loading and off-loading points • Modular pressure control and heat exchanger
• Natural gas pipeline sampling assemblies for easy maintenance
• Unique spiral wrapped heat exchange element
Technical Data
provides up to 100 square inches of heat transfer
CONSTRUCTION 316L stainless steel
area.
OUTLET PRESSURES 0–10, 0–25, 0–50, 0–100, 0–250, and • Available in 120VAC or 240VAC
0–500 psig
• Optional TCO heating cartridge and proportional
INLET PRESSURE up to 6000 psig at 380° F (193° C) controller
HEATING CAPACITY 40, 50, 100, and 150
RANGES (IN WATTS)
CV COEFFICIENTS 0.06, 0.025, 0.2
CERTIFICATIONS CSA certification # LR-82566-5
ATEX Directive 94/9/EC
Certification # TRL03ATEX11001X

GO Regulator
405 Centura Court • PO Box 4866 (29305) • Spartanburg, SC 29303
Phone (864) 574-7966 Fax (864) 574-5608
www.goreg.com • [email protected]
HPR-2 Series
How to Order
Standard items in bold

H2 – 4 Z 3 3 H 3 G 4 1 4 7
BODY MATERIAL OPTIONS
1 316L stainless steel 1 TCO thermistor
4 Monel® 5 6000 psig inlet w/TCO thermistor
(1-pc assy.)
PORT CONFIGURATION
7 6000 psig inlet w/standard thermistor
Z One inlet port, one outlet port
(1-pc assy.)
For more configurations, see page 32
B TCO thermistor w/
TEMP. RANGE/HEATING TYPE Teflon®/Inconel® diaphragm
1 55° F–85° F
CAP ASSEMBLY
2 75° F–175° F
1 Tamper-proof, standard, stainless steel
3 130° F–300° F
4 Tamper-proof, panel mount,
4 260° F–380° F
stainless steel
HEATER WATTAGE
HEATER BLOCK PORTING
1 40W
1 Standard block
2 50W
2 Extra outlet block
3 100W
For more blocks, see pages 34–35
4 150W
HEATER BLOCK TYPE
SEAT MATERIAL
3 120 VAC
A Tefzel®
4 240 VAC
B CF Teflon®
5 No electronics
C Polyimide
8 Proportional 120 VAC
H PCTFE (formerly Kel-F®)
9 Proportional 240 VAC
Q PEEK™
OUTLET RANGE
FLOW COEFFICIENT (Cv)
C 0–10 psig
3 0.06
D 0–25 psig
E 0–50 psig
NOTE: The choices above represent an abbreviated list of the more commonly G 0–100 psig
ordered options. For a complete listing of all available options, please
I 0–250 psig
see the Selection Wizard on the GO website at www.goreg.com or
contact the factory. J 0–500 psig

Maximum Temperature & Operating Inlet Pressures

HPR-2 Electric 2-piece Assembly HPR-2 Electric 1-piece Assembly
(Heater block and regulator body separate) (Integral heater block and regulator)
MAXIMUM OPERATING INLET MAXIMUM OPERATING INLET
SEAT MATERIAL MAXIMUM PRESSURE @ PRESSURE SEAT MATERIAL MAXIMUM PRESSURE @ PRESSURE
Up to 175° F (80° C) @ 3600 psig (24.82 MPa) Up to 175° F (80° C) @ 3600 psig (24.82 MPa)
176° F to 300° F 176° F to 300° F
@ 1000 psig (6.90 MPa) @ 1000 psig (6.90 MPa)
Tefzel® (80° C to 148° C) Tefzel® (80° C to 148° C)
301° F to 380° F 301° F to 380° F
@ 400 psig (2.76 MPa) @ 400 psig (2.76 MPa)
(148° C to 193° C) (148° C to 193° C)
Up to 175° F (80° C) @ 3600 psig (24.82 MPa) Up to 175° F (80° C) @ 3600 psig (24.82 MPa)
176° F to 300° F 176° F to 300° F
@ 1000 psig (6.90 MPa) @ 1000 psig (6.90 MPa)
High density Teflon® (80° C to 148° C) High density Teflon® (80° C to 148° C)
301° F to 380° F 301° F to 380° F
@ 400 psig (2.76 MPa) @ 400 psig (2.76 MPa)
(148° C to 193° C) (148° C to 193° C)
PCTFE (formerly Kel-F®) Up to 380° F (193° C) @ 3600 psig (24.82 MPa) PCTFE (formerly Kel-F®) Up to 380° F (193° C) @ 3600 psig (24.82 MPa)
Polyimide Up to 380° F (193° C) @ 3600 psig (24.82 MPa) Polyimide Up to 380° F (193° C) @ 6000 psig (24.82 MPa)
PEEK™ Up to 380° F (193° C) @ 3600 psig (24.82 MPa) PEEK™ Up to 380° F (193° C) @ 6000 psig (24.82 MPa)

4 GO Regulator Vaporizing Pressure Regulators

HPR-2 Series
Outline & Mounting Dimensions

Ø 0.30" (7.6mm) on 4.29" (109mm) BC

5.67"
(144mm)
5.61" 6.55"
(142mm) (166mm)

A.C. IN

1 2 3 4

10-32UNF × 0.25
Min Full Thds (2×) 1.50"
(38mm)
10.3"
(262mm)

¼" FNPT
Outlet

0.50" (12.7mm) 1/8" FNPT

Inlet

GO Regulator Vaporizing Pressure Regulators 5

Porting Configurations (Pressure Regulator Body)
for HPR-2 Steam & Electric and HPR-2XW Steam & Electric Series

270˚

180˚ 0˚

A C D
90˚

G L M

N V
P

W X Y

Location of ports from top view. Arrow pointing toward body is inlet. Arrow pointing away from body is outlet.
32 GO Regulator Vaporizing Pressure Regulators
Heater Block Configurations
for HPR-2 Steam & Electric and HPR-2XW Steam & Electric Series

FRONT VIEW
SIDE VIEW

1/4" FNPT
1/8" FNPT OUT
1/4" FNPT OUT
FRONT VIEW SAMPLE IN

F-6K FILTER
1/4" FNPT OUT
1/4" FNPT
1/8" FNPT SAMPLE IN
SAMPLE IN

BOTTOM VIEW BOTTOM VIEW

BOTTOM VIEW

1/4" FNPT INLET WITH EXTRA OUTLET @ 270° LOW VOLUME WITH F-6K
STANDARD BLOCK, STEAM STEAM OR ELECTRIC STEAM OR ELECTRIC

FRONT VIEW

FRONT VIEW 1/4" FNPT OUT FRONT VIEW

1/4" FNPT OUT 1/4" FNPT OUT

1/8" FNPT 1/8" FNPT

1/8" FNPT SAMPLE IN SAMPLE IN
SAMPLE IN

BOTTOM VIEW BOTTOM VIEW

BOTTOM VIEW

EXTRA OUTLET @ 270° REVERSE BLOCK, ELECTRIC

STANDARD BLOCK, ELECTRIC STEAM OR ELECTRIC

REMOVEABLE FILTER (XW)

FRONT VIEW

SIDE VIEW
1/4" FNPT
OUT
1/8" FNPT OUT

1/8" FNPT 1/8" FNPT SAMPLE IN

SAMPLE IN

BOTTOM VIEW
BOTTOM VIEW

1/8" FNPT OUTLET

XW BLOCK
STEAM OR ELECTRIC STEAM OR ELECTRIC

GO Regulator Vaporizing Pressure Regulators 35

 REMOVABLE FILTER (XW)

SIDE VIEW
1/4" FNPT
SIDE VIEW OUT
1/4" FNPT
1/8" FNPT 1/8" FNPT OUT
SAMPLE IN SAMPLE IN

F-6K FILTER F-6K FILTER

BOTTOM VIEW BOTTOM VIEW

LOW VOLUME EXTRA OUTLET WITH F-6K LOW VOLUME XW WITH F-6K
STEAM OR ELECTRIC STEAM OR ELECTRIC

FRONT VIEW

1/4" FNPT
1/8" FNPT OUT
SAMPLE IN

1/4" FNPT OUT

SIDE VIEW
F-6K FILTER

BOTTOM VIEW

BOTTOM VIEW 1/8" FNPT

SAMPLE IN
LOW VOLUME WITHOUT F-6K LOW VOLUME REVERSE
STEAM OR ELECTRIC BLOCK WITH F-6K, ELECTRIC

36 GO Regulator Vaporizing Pressure Regulators

For Your Safety
It is solely the responsibility of the system designer and user to select products suitable for their specific application
requirements and to ensure proper installation, operation, and maintenance of these products. Material compatibility, product
ratings and application details should be considered in the selection. Improper selection or use of products described herein can
cause personal injury or property damage.

Hastelloy® is a registered trademark of Haynes International, Inc.

Monel® is a registered trademark of Special Metals Corporation.
Teflon® and Tefzel® are registered trademarks of the DuPont Company.
Kel-F® is a registered trademark of 3M Company.
PEEK™ is a trademark of Victrex PLC.
Viton® is a registered trademark of DuPont Dow Elastomers.