Connect the charging cable to the USB port of the computer (or

12.0. FPV Troubleshooting 12.2 The Image quality received by the glasses is
4. Battery installation 5.0 Aircraft battery charge the USB port with DV5V output), the charging line indicates that
12.1 There Is no Image on the glasses
display screen:
poor or the wireless transmission distance is
near:
1)If there is a same frequency radio transmission
14+ 4.2 Telecontroller function introduction
for telecontroller Tips:Please charge before use!
the red light is on; then the balanced charging port of the battery
end is connected to the balanced charging port of the charging
line, Flashing, full green after the lights long; when the green light
1)Check the power supply of the glasses and equipment interference in near area .the FPV system AGES 11111 is long after the battery recharging for 20 minutes to achieve full
the power supply of the aircraft if its ok and is 4e . 12 ■ Clw * Input
should select other frequencies,avoid the frequency of full power.
the battery adequate or not . interference or avoid use in the same field. ANGIE/W(20W Wireless control 5.30 Waded
Vibration tips
IAANUAL flight mode simulator system lamanission Checking codes methods:
2) Check whether the receiving channel of the 2) If the glasses antenna has been installed USB charging line Output
glasses is consistent with the transmitter ©The terminal of the aircraft is connected with the power supply,
On/Off
channel. 3) If there is a obstruction between the glasses and the Battery and the state of the flight control indicates that the red light is
aircraft, such as the mountain, house, tree, etc. Indicator light Pitch fine-tuning Open the battery cover
flashing.
©Connect the aircraft terminal power supply after 30 seconds and
Throttle fine-tuning 6.0 Operation instructions hold the BIND button on a telecontroller to open the telecontroller
13.0. Accessories list Throttle push rod power source switch, then start to check code, after complete code,
pip, down, left and the aircraft Indicator light switch to slowly flashing, remote control
right steering function) 6.1 Boot program Indicator light will keep shinning.
Direction push rod Right indicator light
1.The code of the aircraft and
, ...--/A YAW fine-tuning (front, left, right, left, sNe Indicator light

\ -\/\ mg1 Propeller A*2

Rudder flow
I Press for shod Nathan the Adder
flying)
Roll fine-tuning
Please use 4 pcs of "AA 1.5V.
batteries and install them by the
telecontroller (need check the codes
when you use at first time,then open
•
.7401ght indicator light
no -,
,1-1-t
pkitimaWN On/Ofl
Aircraft *1 Remote controller *1 Propeller B*2 USB charging line *1 I flow an switch drcularly (minims direction of positive and negative the telecontroller power source ,41/4
ndder Mw, remote vibration have
ANGLE flight mode poleatty (do not mix different button,then turn on the aircraft
button
...-
..
--,
bne time prompt sward adder flow,
I remote control vitiation have two
Ames prompt, MaXi1111111 adder flow,
Oda pressing Monter eubs
stable flight mode
sixes of batteries)
power source to complete the code
automatically.
he aircraft
connects the
bingt1 Code

power supply BIND button

I remote control vibration have three HORIZON flight mode 2. Aircraft calibration
o Imes prompt) Shod mewing to enter emiauto
.w■w.-•_ww rade light mode 3. Aircraft unlock Note:
Codes CH/GAME
Aircraft batteries *1 Propeller guard *4 Impeller *1 Manuar1
INSTRUCTION MANUAL Tips:Please charge before usel FCCE Long preedw the boot to Short pressing sr/Uwe pas MANUAL flight mode 4. Slowly push the accelerator from 1. The aircraft receiver antenna should be erected before
enter the codes Meths, transmkalon frequency point, long Short pressing to enter the adnual the rocker and take off. fighting , to increase the communication distance.
short mewing no fmclion pressing enter emulator motley flight mode button 2.Choose a larger space and soft ground for frying.

6.2 Aircraft calibration and unlock Calibration method

1.0 Know your aircraft Calibration method
Catalog i
7.4"Nlinki"ariat
To make the throttle rocker and the pitching rocker under at the
lowest position, then the vehicle can be calibrated.,When 1 ti 12111111r1i
1.0 Know your aircraft 2 calibrating, the status indicator red light of aircraft will flash iff
The main structure is made of PC material, and the new industrial and modular
VIZI"
;ad light flashes thaw
continuously for three times, that means calibrating is successful. Tum Tum
2.0 Parameter 3 design improves the product development, easy installation, maintenance, Mee continuously
right left
wa•■••A
rs-••
3.0 About flight control 5 replacement and upgrade. Unlock method Put In the lowest

4.0 Remote control 6 Equipped with 5.8G real-time graphics transmission system, which gives you different Put the throttle rocker at the lowest position and position as well Falling
visual effects the roll rocker to the right
5.0 Aircraft battery charge 8 Unlock method When left controller (throttle) pushes left or When left controller (throttle) pushes up or
1.Forward motor 7. Graphic transmission Aircraft locking right, the aircraft rises or falls accordingly. down, the aircraft turn left or right accordingly.
6.0 Operation instructions 8 Sideways rocker
Put the throttle in the lowest position and has no operation Place the throttle
to the right
7.0 Operation and control 9 2. Reversing motor 8. Aircraft upper cover for 5 seconds. rocker to the
lowest position
8.0 Three flight modes 12
3. Forward propeller 9. Airframe ic;i; Tips:
9.0 Flight environment 13 Before the aircraft take off,make sure that the aircraft is
10.0 Installation method of propeller 14 4. Reversing propeller 10. Batteries placed on the horizontal surface for proofreading,ensure that
Flying on Flying on [
the aircraft flies smoothly after take off.when aircraft deviation the right
11.0 Troubleshooting 14 5. Camera 11.Rubber band the left
from impact or collision,it also can be calibrated in same way.
12.0 FPV troubleshooting 15 6. Flight control 12.Propeller ring
7.0 Operation and control Moving backward
13.0 Accessories list 15
7.1 Rocker operation method When left controller (throttle) pushes up or down, When right controller (throttle) pushes up or down,
the aircraft turn left or right accordingly. the aircraft fly on the left or right accordingly.
As for the Sensitive induction,For be9inners,suggest to operate joystick slowly.
If the craft drops slightly during steenng,can push the left joystick slowly so that can climb
01 02 up to a certain height at the same time. 9
When operating, avoid pushing the throttle substantially.

8.0 Three flight modes flight tilt towards to the left [

Joystick left push
2.2 Function features 7.2 Fine-tuning operation method Pitch fine tuni g Auto stable mode: This mode is suitable for
Pre
2.0 Parameter 5.8G 3dBi micro antenna Fine-tuning of aircraft movements
primary user. With this mode, the aircraft will
2.4G receiving antenna automatically restore horizontal position according
Lifting the throttle rocker slowly,When the aircraft to the Roll, Pitch, and Yaw joystick back in middle.
leaves the ground,lf the craft tends in different For example, when the Roll joystick is turned to
44mm three bladed propeller directions,can use fine-tuning to do corrected action. the left and the Roll joystick automatically returns,
2.1 Vehicle parameters
8520 2S motor the vehicle will automatically resume its horizontal automatically restore
1. Pitch fine tuning position. Auto back to middle horizontal posihion
Propeller: 44mm (triple blade propeller)
When the aircraft leaves the ground, Semi automatic stabilization mode: This mode Soft: Auto stable mode
Fuselage (L * w * h): 88*58*40mm tilt forward while flying,adjust slightly downward. epRight rotation
is suitable for intermediate user that can control Violence: manual mode
Weight: 42g (excluding battery) tilt back while flying,adjust slightly upward. .0J -fik of aircraft well. The joystick is "auto stable mode" Sot Auto stable mode
before hitting a certain proportion, and exceeds Violence: manual mode
Flight control: customized version of steady this ratio will change to "manual mode'. That
2. YAW fine-tuning means soft control is automatic stabilization, and
flight control 110 Centigrade wide angle When the aircraft leaves the ground, vW.■ violent operation is manual mode.
Motor: 8520 2S motor 1000TVL COMS camera Rotate to the right while flying,adjust to the left slightly.
Battery 7.4V, 300mAh, 25C YAW fine-tuning Left rotation Manual mode: This model is suitable for advanced
Battery: 7.4V, 300mAh, 25C Rotate to the left while flying,adjust to the right slightly.
user that can control all kinds of stunt performance, Push the joystick to the Continue flying to the left
showing its super reaction and control ability. Under left and automatically
Flight time: 6 minutes 3. Roll fine-tuning this mode, the aircraft will automatically restore back to middle place
Working environment temperature: F "9 When the aircraft leaves the ground, Oci-7,(4 horizontal position according to the Roll, Pitch, and
Yaw joystick back in middle. For example, when
-10°C to +40°C
CZ
EL .0 (g)
Fly to the right while flying,adjust to the left slightly.
Fly to the left while flying,adjust to the right slightly. '<*•■ you hit the Roll joystick to the left, the Roll joystick .›(!)
keep sailing 2.4GHz mufti-function automatically returns to middle, while the vehicle
FPV Safely flight
for 6 munites remote control Roll fine-tuning
Fly left Fly right continues to roll to the left side without recovery. -rabont11;.thedght
03 04 Only when the Roll joystick hits the same degree to
the right, the vehicle will roll to the right to recover The joystick is pushed
to the right level
horizontally.

10.0 Installation method of propeller Propeller installation: Hold the small cap
3.3 Supports indication of current frequency points 9.0 Flight environment
3.0 About flight control Please do not use this product under below The propeller installation of aircraft has position of the propeller, press the motor shaft
Frequency (Unit:MHz) envlronment,avold accidental injury or requirements. Please install it according to the down, and be careful not to deform the
3.1 Support Freerider simulator wireless control function Frequency point corresponding code,the codes shows as below. propeller.
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 damaged aircraft.
indicator light Camera
5658 5695 5732 5769 5806 5843 5880 5917 1)High voltage lines, parks, railways, B
figmqP4mP-
111.1111,
.. • CH1, the frequency point indicates that the blue light (as shown on the right) flashes at intervals
highways and so on.
of 2 seconds; CH2 flashes 2 times per second for 2 seconds; CH3 blinks 3 times per second; 2) Thunderstorms,wind ,snow and rain, etc.
NE CH4 flashes 4 times at intervals of 2 seconds; in tum, 2 times.
r.
Adopt professional competition frequency points,No interference from one another will occur
when multiple people use the same field.At the same time, this product can also supports 2.4G 9.1 End flight C) Manual landing.
3.2 Support Betaflight software, PID parameters adjustable remote control switching frequency point function. © Switch off the power of the aircraft first, then 11.2 Solution for airframe shaking
Flight through turn off the telecontroller power supply.
11.0 Troubleshooting 1)Check whether the propeller is deformed and
2' Adjustable parameters Er Adjustable parameters 2' Adjustable parameters replace the new propeller.
4.0 Remote control (2) Remove the battery from the aircraft. 11.1 Remote control and aircraft
2) Calibrate the gyro by placing the aircraft at the
unresponsive solutions:
4.1 Vibration alarm prompt horizontal plane.
1)Make sure the code successfully. see
• Law vibration alarm for low voltage remote terminal of aircraft. Alarm voltage (single battery3.7V) page 8 for codes. 11.3 Telecontroller vibration solutions:
• Remote control low voltage vibration alarm. Alarm voltage (single battery 1.02V) 2) Whether the battery is low. 1) When the telecontroller is vibrating, check the side of
* It will have vibration alarm once lose signal. When the remote control is out of contact with the aircraft Vibration alarm the aircraft and the telecontroller if have enough power or
signal, the remote control will send a vibration prompt. 3) Make sure that the remote control is the
prompt function original one. if have object blocked between the aircraft and the remote
The button can impels the vibration prompt. When the remote control button is operated at any time, the controller that causes a weak reception signal.
Open function Open function Open function remote controller will send out a shock prompt 4) Confirm if is unlocked after code
2 ) The reason for the remote controller vibration
Tips: No indicating area not open yet.
05 a Support 3 rudder volume (DM key) and three flight modes (ANGLE / HORIZON /
MANUAL three keys), NEW occasionally is that the signal is weak or the
battery is about to go into a low -voltage state .
The remote control panel function sham as below:
 • * •
AGES 14+ Key description Menu interface guide map
(Can optional) Brightening -
[+]: In the menu mode for the down function. In
the non-menu mode, press to adjust to the next - 0 Brightness {
frequency of the current frequency. CO Darkening
[MENU]: menu switch.
[-]: in the menu mode for the up function. In the
non-menu mode, short press to adjust to the - © Contrast
r Q Enhancement
previous frequency point. L p Reduced
[SCAN /c]]: short press for the automatic
frequency function, long press for the switch Short press Intensity - Loop switch
function. O MENU o SCAN / 0.) Saturation {
the "Menu
• Change
hange
Tips:
Turn on the machine, long press [SCAN MA button, the - 0 AV/AVIN Switch
Tips:Please charge before use! indicator light from flashing to light is on, that is, complete
the boot. When the camera is turned off, the indicator light

FCCE_ FPV goggle instruction manual

turns off from flashing to complete shutdown. Through the ,
ventilation hole can
see the light fleisties
- Q Exit

The menu adjustment uses the icon

() The menu adjustment uses the icon
Features -No M •
+
•
MENU
•
-
•
SCAN /C) }
One key
HO display Mini type auto-search function
First person Real-lime display Adjustable L
. Short press [MENU] key to enter Short press [MENU] key to enter menu option Function:
view of arrant frequency head band menu option Function:
[+]
Brightness adjustment: short
Specifications BRIGHTNESS.......................1.
f! BRIGHTNESS 50 AV / AV IN Mode setting: [+]
press [+] or [- ] button to
[-] When this option is selected, INPUT -a. INPUT
Working voltage: 1s battery(3.7-4.2v) E adjust the brightness.
9.7V 9.7V
press the [+] or [-] button Ef AV DAV IN DAV Ef AV IN
E [-]
First-person perspective, Working current: 350--450mA 00 to select AV or AV IN mode. 3.7 V 3.7 V
Receiving sensitivity: -95dBM 3-1
experience more shocking Weight: 164.7g (without antenna and rLi Contrast adjustment: Short CONTRAST 10
[+]
CONTRAST
headband)
press 1+1 or I-1 button to
Size:138129'79mm( without antenna 9.7V [-] 9.7V
To exit the menu: Press
seat and antenna height) adjust the contrast. the [MENU]] button to INPUT
Receiver connector:RP-SMA male exit the menu interface. Ef AV DAV IN
E 3.7 V 3.7 V
Built-in battery
Receiving frequency:5.8G 40CH N., Saturation adjustment:
SATURATION SATURATION 50
short press [+] or [-]
3-inch high-definition screen, whether it is to play through or look at the button to adjust the color. 9.7V 9.7V
scenery, every detail is not missed. 01 129mm 02

4;0. 4.ZL■150t17i1 6 ■•

Description Adjust the frequency of use as follows Common troubleshooting

1. AV IN input port: In AV IN mode can enter the HD display [ SCAW 01 ]: short press a key search frequency, long press for the switch function. Goggles display screen No image:
video signal.
2.Antenna port: thumb and forefinger pinch the • 3-inch high-definition screen, In the non-menu interface for the FM (1) Check to confirm whether the correct boot (long press [SCAN /0] , turn
antenna port, turn clockwise, twist it. whether It Is to play through or interface wake-up function, enter the FM
[-] on the light from the flash to light, that is, has been properly boot).
3. Ventilation holes: all breathable (see page 6). look at the scenery, every detail interface, short press I-1 to adjust to
(2) Check whether the frequency of the goggles and the transmitter frequency is
4. Snap-on head hole: the headband from the eye is not missed. the current frequency of the previous
lens with the middle of the gap in the hole into the hole. frequency, short press 1+1 to adjust to 3.70 5.865GHZ
[+] 3.7V 5.845GHZ
consistent.
The side headband penetrates the side of the head hole, the current frequency of the next (3) Check to see if the battery power of the aircraft or goggle is sufficient.
the top of the headband into the top of the head hole. Screen size:3 inch LCD display
Screen resolution:500x300 pixels frequency.
5. Charging indicator: red light when charging light; (4) Check if the antenna of the goggle is properly installed.
full power, the indicator goes off. Frequency table
6. [E]: Key Function Details on page 7. Unit : GHz
7. [MENU]: Key Function Details on page 7. • Support a key search frequency Goggles received the image signal quality is poor or wireless transmission
--"---„, 1 2 3 4 5 6 7 8
8. [-1: Key Function Details on page 7. distance near:
9. [SCAWC]: Key Function Details on page 7. • OSD Real-time display of A 5.865 5.845 5.825 5.805 5.785 5.765 5.745 5.725
10. Micro USB charging port: This product battery voltage (1) Whether the same frequency of radio frequency transmission equipment
B 5.733 5.752 5.771 5.790 5.809 5.828 5.847 5.866
supports DC5V charging real-time standby function. interference, FPV system should choose other frequencies, to avoid the
When you are outdoors, you can use your charger or its C 5.705 5.685 5.665 5.645 5.885 5.905 5.925 5.945 interference frequency or to avoid the use of a unified site.
mobile power while charging.
11. Eye ring: eye ring is used to protect the Right side Left side D 5.740 5.760 5.780 5.800 5.820 5.840 5.860 5.880 (2) Whether the antenna of the goggles and the transmitter is installed.
surrounding parts of the eyes, so that the wearer wear Battery voltage Frequency display
more comfortable. display E 5.658 5.695 5.732 5.769 5.806 5.843 5 880 5.917 (3) Whether the goggles and the transmitter between the mountains, houses,
03 04 11 trees and other obstacles, should be used in the open space FPV system.

AV IN function Stable display, reasonable focal Precautions packing list

The video signals of external devices (such as DVD) can be input
Ventilation holes length and perspective, even Before use, make sure that the battery power of the device is saturated.
to the end of the glasses via the AV IN connector to display their • All-round ventilation, the effective beginners can quickly adapt. To reduce the risk of fire, electric shock, or product damage, do not expose the unit to rain,
images. formation of convection. moisture, dripping, or splashing water. Do not place liquid, such as a vase, on the unit. ..-1.1757-_____7•70 11
00: Tips:Please charge before use!
Not halo screen
Please avoid falling or strong collision of the product, do not let the product was violent vibration,
otherwise it may lead to product damage or display is not normal.
I . lili
‘,-,■111RIL
p)
/ 2:::::24
INSTRUCIION MAHLY.I.

Built-in battery *
AV IN input port NOmiiiitobow Do not use in particularly cold, hot, dusty and humid environments. Goggles*1
Working voltage: In the following places, pay special attention, so as not to cause video goggles failure. S raight rod antenna*1 Manual *1
1S batter (3.7 - 4.2V)
(1) where there is a lot of sand or dust.
'!a
(2) Exposure to water, such as in the rain or on the beach when the use of the machine, the '
product lens sticky dust or dirt, please use a professional lens cleaning paper clean. -
4
AV line (3) Do not force the video goggles into stuffed or crowded package, so as to avoid damage to
Micro USB Micro USB
charging port internal parts or personal injury. charging cable * 1 Lens wipes *2
Charging real-time standby function
This product supports DC5V charging real-time • Tips:
When you need to watch the video for a long time, we recommend that you
standby function. When you are outdoors, you
take a video break every 50 minutes. If your eyes and other body parts feel
can use your charger or other mobile power unwell, please stop using this product. Eyes and other body parts of the
while charging. Charging indicator original discomfort of the user, please consult the relevant medical institutions
DC 5V to obtain the use of recommendations.