Technical specification Parts

A B C
Display
Resolution 800 x 480
Inst
Installation

ENGL
Installation Ma

ISH
ENGL
Installation Manual

ISH
ENGL
alla Manua

ISH
tion nual

ENGL
ISH
Ma l
nua
l

ban
dg.
com com com com
ban ban ban
dg. dg. dg.
Brightness >1200 nits
Touch screen Full touch screen (multi-touch)
Viewing angles D E F
(typical value at contrast ratio = 10)
Left/right: 70°, top: 50°, bottom: 60° P2005
Electrical Installation Guide
Supply voltage 12/24 V DC (9.0 - 31.2 V DC min - max) G H
650 mA/320 mA at 12 V DC (backlight full/off )
Power consumption
350 mA/190 mA at 24 V DC (backlight full/off )
Recommended fuse rating (12 V / 24 V) 3A
Environmental
A. P2005 unit
Temperature range -15°C to +55°C (5°F to 131°F)
B. Panel mounting kit
Storage temperature -20°C to +60°C (4°F to 140°F)
C. Documentation
Waterproof rating IPX6, IPX7
D. 3-way adapter cable
Category Protected
E. Communication cable
Shock, vibration and humidity According to IEC 60945
F. Fuse kit
Interface/Connectivity
Ethernet 1x (RJ45) 100Base-TXS, 8P8C connector, IPv4 G. Bracket kit

Lightweight Ethernet protocol IEE 802.3 H. Suncover (sold separately)

Maximum data rate 450 sps addressed to device, 500 sps unintended *988-12388-003*

Buffer capacity Dynamic serial buffer

NMEA 2000 1x (Micro-C ,1 LEN)
Data card reader 1x slot (microSD)
System example
Comms
IEC 61162-2 ports 2x
GPS GPS GPS
Digital input 1x
Analog input 1x
Power output (+16 V DC, 70 mA) 1x
Datagram types NkPgN and UdPbC
P2005 / P3007 P2005 / P3007 P2005 / P3007
Physical T BACKLIGHT
MOB KEY CONTROL SPEED
Compass Safe Distance - Metric, imperial 0.6 m (1.97 ft)
Weight (display only) 0.54 kg (1.18 lbs)

Bracket mounting Dimensional drawings 148.2 mm

(4.62”) T
152.0 mm 58.0 mm T
(5.98”) (2.27”)
136.0 mm
120 mm
(4.72”)

(5.35”)

MX JUNCTION BOX

T
ANALOG
CAN BUS CAN BUS CAN BUS NMEA 0183/
DIGITAL ETHERNET
TERMINATOR BACKBONE DROP CABLES IEC 61162-1/-2
94.0 mm 8.0 mm 94.0 mm FREQUENCY
Unit removal (3.70”) (0.32”) (3.70”)
Connector overview Communication cable
A
A. Grounding, M4 threaded insert B C Refer to the Operator Manual for software setup. Wiring illustrations only include the required wires for the example.
B. Comms (communication), 19-pin connector
IEC 61162-2 port 1 RX: 6, 5, 4, Drain N.C
C. Power, external alarm, NMEA 2000 and Ethernet, 14-pin connector IEC 61162-2 port 1 TX: 10, 17, 18, 19 12 1
D. Communication cable D E 11 2
13 14
IEC 61162-2 port 2 TX: 3, 16, 15, 19 10 3
E. 3-way adapter cable 18 19 15 Cable plug
9 4
17 16
8 5
F. NMEA 2000, Micro-C connector 7 6
IEC 61162-2 port 2 RX: 7, 8, 9, Drain N.C
G. Ethernet, RJ45 Ethernet connector Digital/Analog: 1, 13, 12, 11, 2, 14
H. Power and external alarm IEC 61162-2
F G H
Pin/Wire Color IEC 61162-2 port 1 Pin/Wire Color IEC 61162-2 port 2
10 black TX common 3 black/red TX common
17 white talker (TX_A) 16 white/red talker (TX_A)
Power and external alarm
18 brown talker (TX_B) 15 brown/red talker (TX_B)
A. 3-way adapter cable E. Power failure alarm output (contact return) A B C 19 drain (gray shrink tube) TX drain 19 drain (blue shrink tube) TX drain
- blue
B. DC negative - black 7 black/white RX common 6 brown/red RX common
F. Power failure alarm output (N/C isolated D
C. +12/24 V DC - red 8 yellow listener (RX_A) 5 yellow/red listener (RX_A)
contact) - yellow E F
D. Fuse (3 A) 9 green listener (RX_B) 4 green/red listener (RX_B)
G. Alert management system G
N.C drain (purple shrink tube) RX drain N.C drain (orange shrink tube) RX drain

¼ Note: Refer to the technical specification for electrical details. Direct antenna connection
IEC 61162-2 port 1 GPS antenna IEC 61162-2 port 2 GPS antenna
8 GPS primary output (TX_A) 4 GPS secondary output (TX_B)
9 GPS primary output (TX_B) 5 GPS secondary output (TX_A)
Ethernet NMEA 2000 A B 17 GPS control input (RX_A)
A B 18 GPS control input (RX_B)
A. 3-way adapter cable A. 3-way adapter cable
B. RJ-45 connector B. Micro-C connector Analog input
The analog port can be configured for backlight control.
¼ Note: Network switches can be used to extend the Pin/wire Color Backlight control A. Potentiometer (10 k - 100 k Ohm, 0.1 W)
network. Routers and repeater hubs shall not be used.
2 red +16 V DC (max. 70 mA) 2 11 A
Network traffic filtering by external managed switch 11 blue/white signal in
supports IGMP version 2. 12 blue/red not used
13 gray/orange ground 13
14 drain (clear shrink tube) not used

Grounding A
Digital input
A. Ground, M4 threaded insert
B C D The digital port can be used for either speed input or as an external MOB key.
B. Grounding cable, min. 0.82 mm2 ( 18 AWG)
C. Star washer Pin/wire Color Speed log MOB
1 pink signal in signal in
D. Screw (M4-.7 X 6 mm)
13 grey/orange ground ground
14 drain (clear shrink tube) not used not used

MOB Speed
¼ Note: It is recommended that the unit ground is connected to the vessel’s bonded ground or a non-bonded RF ground.
A. Momentary push button A speed log that outputs 200 pulses per nautical mile can
be connected to the digital port.
1 A 1
A. Speed log (200 pulses/NM)
A
For more information on alerts, refer to the Operator manual. B. Ship’s ground
13 B
13
For product manuals, technical specifications, certificates and declarations, refer to: www.navico-commercial.com