NOTE: When exiting dC330, the machine resets and communication between the PWS and the machine

is momentarily lost. The PWS will reconnect automatically. Table 1 Input Component Control Codes Code 007-103 007-104 007-105 007-106 007-107 007-108 007-109 007-110 007-111 007-112 007-113 007-114 007-115 007-116 007-117 007-118 007-119 007-120 007-121 007-122 007-123 007-125 007-128 008-100 008-102 008-103 008-104 008-105 008-106 008-107 008-108 008-109 008-110 008-300 Tray 1 Level Sensor Tray 2 Level Sensor Tray 3 Level Sensor Tray 4 Level Sensor Tray 1 No paper Sensor Tray 2 No paper Sensor Tray 3 No paper Sensor Tray 4 No paper Sensor Tray 5 No paper Sensor Face Up Tray Detect #1Feed Out Sensor #3Feed Out Sensor #4Feed Out Sensor Regi Sensor Dup Wait Sensor T/A Sensor TTM Path Sensor1 TTM Path Sensor2 OHP Sensor#L OHP Sensor#R DUP Open Switch Tray 4 Size Switch 4 (3TM only) Tray 4 Size Switch 3 (3TM only) Tray 4 Size Switch 2 (3TM); Size Switch 3 (TTM) Tray 4 Size Switch 1 ON = AN value ON = AN value ON = AN value ON = AN value Lift Up. ON = High Lift Up. ON = High Lift Up. ON = High Lift Up. ON = High No paper. ON = High No paper. ON = High No paper. ON = High No paper. ON = High No paper. ON = High Low when Tray is installed. ON = Low Paper detected. ON = High Paper detected. ON = High Paper detected. ON = High No paper -ON = Low Paper detected. ON = High Paper detected. ON = High Paper detected Paper detected ON = Low ON = Low ON = High ON = AN value ON = AN value Tray 3 Size Switch 2 (3TM); Size Switch 3 (TTM) Tray 3 Size Switch 3 (3TM only) Tray 3 Size Switch 4 (3TM only) ON = AN value Tray 3 Size Switch 1 ON = AN value Tray 2 Size Switch 4 ON = AN value Tray 2 Size Switch 3 ON = AN value Tray 2 Size Switch 2 ON = AN value Tray 2 Size Switch 1 ON = AN value Tray 1 Size Switch 4 ON = AN value Name Description

Table 1 Input Component Control Codes Description High when Open is detected. ON = High High when Open is detected. ON = High High when Open is detected. ON = High Low when Open is detected. ON = Low High when Open is detected. ON = High IBT is not at Home Position. Open circuit. It is necessary to operate IBT 5V ON. ON = High

Code

Name

001-300

INTLK_1

001-301

INTLK_2

001-302

LH LOW I/L SW

001-304

LH 3TM I/L SW

001-306

INTLK_3

004-100

Belt Home Sensor

004-101

Drum Motor YMC Fail Detec- PR (Drum) Motor YMC Failure. ON = High tion Fan rotation is stopped. ON = Fault No paper detected by Document Sensor. ON = High Paper detected by Regi Sensor. ON = Low Paper detected by Exit Sensor. ON = Low Paper detected by Dup Sensor. ON = Low No paper detected by #1 Size Sensor. ON = High No paper detected by #2 Size Sensor. ON = High Document Exchange Instruction. on from IISS. ON = Low Platen Cover Open. ON = High Top Cover Inter Lock Open. ON = High Document Regist. ON = Low Deactuation of Regi Sensor. ON = Low DADF is not installed. ON = High Document is detected. ON = APS SNR1: Low, APS. ON = High Document is detected. ON = APS SNR3: Low, APS. ON = High Flash Memory writing is not in progress. ON = Inside PWBA High when FAN failure is detected. ON = High Low when Platen closed. ON = Low Low when Platen closed. ON = Low ON = AN value ON = AN value ON = AN value

004-102

Drum Motor K Fail Detection PR (Drum) Motor K Failure. ON = High

004-200

FAN_LOCK_FAIL

005-102

Document Sensor

005-110

Regi Sensor (DADF)

005-115

Exit Sensor

005-119

Dup Sensor

005-150

#1 Size Sensor

005-151

#2 Size Sensor

005-201

Exchange from IISS

005-300

Platen I/L Switch

005-301

Top Cover I/L Switch

006-160

Polygon Motor Ready Signal Regular rotation of Polygon Motor. ON = Low

006-201

Sheet Abort

006-212

IIT Regi Sensor

006-240

DADF Exist

006-251

APS Sensor1

006-253

APS Sensor3

006-272

PM-0

006-281

IPS Fan Fail

006-300

Platen I/L Switch

006-301

Angle Sensor

007-100

Tray 1 Size Switch 1

007-101

Tray 1 Size Switch 2

007-102

Tray 1 Size Switch 3

Table 1 Input Component Control Codes Description 012-224 012-225 012-300 012-301 012-302 012-305 H-Tra Interlock Sensor Docking Interlock Sensor Top Cover Interlock Switch Stapler Front Corner Sensor Stapler Move Sensor CRU Connection of color is open (The CRU in use is present, or it is not present). Low=new, High=old Code Name Description

Table 1 Input Component Control Codes

Code

Name

009-101

Toner_Y New

Non-transmissive position. O Front Corner position. ON = Open. ON = High Docking release. ON = High Open. ON = High

Front Cover Interlock Switch Open. ON = High

009-102

Toner_M New

CRU Connection of color is open (The CRU in use is present, or it is not present). Low=new, High=old

009-103

Toner_C New

CRU Connection of color is open (The CRU in use is present, or it is not present) Low=new, High=old Code 001-001 001-003 004-001 Flicker Steering Motor Delayed_off Name CRU Connection of color is open (The CRU in use is present, or it is not present) Low=new, High=old ON = High CRU is installed CRU is installed CRU is installed CRU is installed Retraction. ON = Low Paper detected. ON = Low Retraction. ON = Low Paper detected. ON = High NotFull. ON = Low Clutch OFF. ON = High Paper detected. ON = High Paper detected. ON = High Paper detected. ON = High Paper detected. ON = High Paper detected. ON = High Higher than the detection surface. ON = High Upper Limit position. ON = High Non-transmissive position. ON = High Non-transmissive position. ON = High Not at Home position. ON = High Low Staple. ON = High Not at Ready position. ON = High Not at Home Position (Roller is down). ON = High Not at Home Position (transmissive). ON = High Home position. ON = High Home position. ON = High Not at Home Position (transmissive). ON = High 004-010 004-009 Drum Motor K (52mm/sec.) 004-008 004-007 004-006 Drum Motor K (104mm/sec.) 004-005 Steering Motor Home Position 004-004 004-003 004-002

Table 2 Output Component Control Codes Description Delay Relay Energize triac to switch in Flicker Resi (220VAC - DC3535 only) Reswitch the Steering Cam to Home p tion once and operate it at half cycle af that. IBT Motor (104mm/ Operate with the IBT Assy. removed to sec.) vent Transfer Belt damage. Drum Motor YMC (104mm/sec.) Main Motor (104mm/sec.) Remove all Drum Cartridges before en gizing to prevent Belt damage.

009-104

Toner_K New

009-150

TNR FULL SNR

009-151

#Y_CRU detect

009-152

#M_CRU detect

009-153

#C_CRU detect

009-154

#K_CRU detect

009-200

2nd BTR Retract Sensor

009-201

POB Sensor

009-203

1st BTR Retract Sensor

010-101

Fuser Exit

010-102

Full Paper Stack Sensor

012-100

IOT Regi Clutch

Rotate at medium speed. Operate the motor with the 2nd BTR nipped, or the Cover opened. Otherwise, the 2nd BT might damage the belt. Returns Steering Cam to home positio ON = Low. Operate with the IBT Assy. removed to prevent Transfer Belt dam Remove all Drum Cartridges before en gizing to prevent Belt damage.

012-101

Compiler Tray Exit Sensor

012-102

Compiler Paper Sensor

012-103

H-Tra Ent. Sensor

012-104

H-Tra Exit Sensor

012-200

Stacker Paper Sensor

012-201

Stacker Height Sensor

012-202

Stacker Upper Limit Sensor

012-204

Stacker Stack A Sensor

Main Motor (52mm/ Rotate at low speed. Operate the mot sec.) with the 2nd BTR nipped, or the LH C opened. Otherwise, the 2nd BTR migh damage the belt. Main Motor (high speed)

012-205

Stacker Stack B Sensor

012-207

Staple Head Home Sensor

012-208

Low Staple Switch

012-209

Staple Ready Sensor

Rotate at high speed. Operate the mot with the 2nd BTR nipped, or the LH C opened. Otherwise, the 2nd BTR migh damage the belt.

012-210

Eject Clamp Home Sensor

012-211

Set Clamp Home Sensor

Rotate at low speed. Remove all Drum tridges before energizing to prevent B damage. Drum Motor K (high Rotate at high speed. Remove all Dru speed) Cartridges before energizing to preven Belt damage.

012-212

Rear Tamper Home Sensor

012-215

H-Tra IOT Full Paper Sensor No paper. ON = High

012-216

Front Tamper Home Sensor

012-217

Decurler Cam Position Sen-

Table 2 Output Component Control Codes Table 2 Output Component Control Codes Conflicts Code 006-031 006-032 006-086 006-091 004-002, 004-012 007-003 007-004 008-001 008-002 008-003 008-004 #2Feed Motor (Fwd) #2Feed Motor (Rev) 005-056 005-055 008-005 008-006 008-007 008-008 #4Feed Motor (Fwd) #4Feed Motor (Rev) #3Feed Motor (Fwd) #3Feed Motor (Rev) #1Feed Motor (Rev) #1Feed Motor (Fwd) HOTLINE_TRAY Not used. Feed (Rotate #1Feed Motor in paper feed direction at 200mm/sec.) Tray 5 FEED Clutch Exchange To ADF 8-002 8-001 IIT Image Area IMG-AREA Signal Output. ON = P727 LVDS (Differential) High Turn ON the document exchange command signal to the DADF SOS Gain Start-of-Scan Sensor gain signal Polygon Motor Start Signal Name Description Conflicts

Code

Name

Description

004-011

Drum Motor YMC (52mm/sec.) 004-002, 004-013

Rotate at low speed. Remove all Drum Car- 004-003 tridges before energizing to prevent Belt damage.

004-012

IBT Motor (52mm/ sec.)

Rotate at low speed. Operate with the IBT Assy. removed to prevent Transfer Belt damage.

004-013

IBT Motor (high speed)

Rotate at high speed. Operate with the IBT unit removed. The Belt might be damaged since the Belt Work Control is not performed. -

004-014

IBT_5V ON

ON = High.

004-050

Fuser Fan, LV Fan Rotate the FUSER FAN, LV FAN and and Rear Fan REAR FAN at high speed. (Rotation is Low Rotation High at Power ON) speed

005-011

Set Gate Solenoid Open

Turn Set Gate Open ON (Towards bottom of Nudger Roll) for 5sec -> Auto OFF

It switches OFF automatically 6sec after LiftUp has started, or when the Level Snr detected LiftUp. LiftUp cannot be performed when the Level Snr should detect LiftUp. Feed (Turn #2Feed Motor On in paper feed direction at 192mm/sec.)

005-012

Set Gate Solenoid Close

Turn Set Gate Close ON (Towards bottom of Nudger Roll) for 5sec -> Auto OFF

8-004 8-003

005-040

Feed Mot.

DADF Feed Motor for 2sec -> Auto OFF

005-055

Belt Motor Non CVT Mode (CW)

Rotate the DADF Belt Motor forward.

005-056

Belt Motor Non CVT Mode (CCW)

Rotate the DADF Belt Motor backward.

It switches OFF automatically 6sec after LiftUp has started, or when the Level Snr detected LiftUp. LiftUp cannot be performed when the Level Snr should detect LiftUp. Feed (Turn #3Feed Motor On in paper feed direction at 192mm/sec.)

005-075

Regi Gate Solenoid Push the Regi Gate with the Arm to turn it ON for 5sec -> Auto OFF

005-081

Exit Motor Non CVT Mode

Operate the DADF Exit Motor

8-005

005-083

Doc Ready

switch ON the Doc Ready signal.

005-084

Doc Set LED

switch ON the DOC SET LED

006-002

It switches OFF automatically 6sec after LiftUp has started, or when the Level Snr detected LiftUp. LiftUp cannot be performed when the Level Snr should detect LiftUp. Feed (Turn #4Feed Motor On in paper feed direction at 192mm/sec.)

IIT Exposure Lamp switch the Lamp ON for 180sec -> Auto OFF

8-008 8-007

006-004

IPS Cooling Fan (Low speed)

After operating the IPS Cooling Fan at high speed for 5sec, operate it at low speed. ON = FAN. ON = 24V, FAN Slow: L->H (About 13V) 006-006 006-005 -

006-005

IIT Scan Motor (Scan)

More it 50mm from current position in Scan direction -> Auto OFF

It switches OFF automatically 6sec after LiftUp has started, or when the Level Snr detected LiftUp. LiftUp cannot be performed when the Level Snr should detect LiftUp. 008-009 Dup Motor (200.1mm/sec.) 008-010 Dup Motor (104mm/sec.) Start operation. Switches OFF automatically at 1000msec. Start operation. Switches OFF automatically at 1000msec.

006-006

IIT Scan Motor (Return)

More it 50mm from current position in Return direction -> Auto OFF

8-010, 011, 012, 053, 054, 055, 056

006-014

IPS Cooling Fan (High speed)

Operate the IPS Cooling Fan at high speed.

006-030

LD ON Enable Signal (concurrently for 4 colors)

8-009, 011, 012, 053, 054, 055, 056

Table 2 Output Component Control Codes Description 8-009, 010, 012, 053, 054, 055, 056 008-034 TTM TA Motor (104mm/sec.) Long TTM TA Motor (192mm/sec.) Long TTM TA Motor (370mm/sec.) Long Regi Clutch #1TA Clutch Invert Clutch CW 8-009, 010,011, 053, 054, 055, 056 008-035 Start operation. Switches OFF automatically at 1000msec. 008-036 Start operation. Switches OFF automatically at 1000msec. 008-037 008-038 008-042 008-043 008-047 008-048 008-049 Start operation. Switches OFF automatically at 1000msec. Start operation. Switches OFF automatically at 1000msec. 8-021, 022, 023, 024, 026, 027, 028 8-021, 022, 023, 024, 025, 027, 028 8-021, 022, 023, 024, 025, 026, 028 8-021, 022, 023, 024, 025, 026, 027 Start operation. Switches OFF automatically at 1000msec. Start operation. Switches OFF automatically at 1000msec. Start operation. Switches OFF automatically at 1000msec. Start operation. Switches OFF automatically at 1000msec. 8-021, 022, 023, 025, 026, 027, 028 8-021, 022, 024, 025, 026, 027, 028 8-021, 023, 024, 025, 026, 027, 028 8-022, 023, 024, 025, 026, 027, 028 Conflicts Code Name Description

Table 2 Output Component Control Codes

Code

Name

008-011

Dup Motor (200.1mm/sec.) Long

008-012

Dup Motor (104mm/sec.) Long

008-021

3TM TA Motor (52mm/sec.)

008-022

3TM TA Motor (104mm/sec.)

Switches on. Switches off automaticall 400msec. Switches on. Switches off automaticall 400msec. Switches on in output direction. Switch OFF automatically at 400msec.

008-023

3TM TA Motor (192mm/sec.)

008-024

3TM TA Motor (370mm/sec.)

Invert Clutch CCW Switches on in Invert direction. Switch OFF automatically at 400msec. TTM TM Motor2 (370mm/sec.) Start operation. Switches OFF automa cally at 1000msec. TTM TM Motor2 . (370mm/sec.) Long

008-025

3TM TA Motor (52mm/sec.) Long

008-026

3TM TA Motor (104mm/sec.) Long

008-027

3TM TA Motor (192mm/sec.) Long

MOB2LED_CHNG MOB SNR2 LED Light quantity switchi signal, Light quantity UP (increase volt at PORT H. ON = ANA Output LED2 L quantity UP 008-050 008-051 MOB2LED_ON MOB SNR2 LED ON. ON = ANA outp MOB1LED_CHNG MOB SNR1 LED Light quantity switchi signal, Light quantity UP (increase volt at PORT H. ON = ANA Output LED1 L quantity UP 008-052 008-053

008-028

3TM TA Motor (370mm/sec.) Long

008-029

TTM TA Motor (52mm/sec.)

8-030, 031, 032, 033, 034, 035, 036

MOB1LED_ON Dup Motor (373.2mm/sec.) 8-029, 031, 032, 033, 034, 035, 036 008-054 Dup Motor (194mm/sec.) 8-029, 030, 032, 033, 034, 035, 036 008-055

MOB SNR1 LED ON. ON = ANA outp Start operation. Switches OFF automa cally at 1000msec. Start operation. Switches OFF automa cally at 1000msec.

008-030

TTM TA Motor (104mm/sec.)

008-031

TTM TA Motor (192mm/sec.)

008-032

TTM TA Motor (370mm/sec.)

Dup Motor (373.2mm/sec.) Long 8-029, 030, 031, 033, 034, 035, 036 008-056 Dup Motor (194mm/sec.) Long 8-029, 030, 031, 032, 034, 035, 036 009-001 #Y_Disp MOT Y Color Disp. MOT turns ON, and swit

008-033

TTM TA Motor (52mm/sec.) Long