ondia Ae 1s 16700 : 2017 Indian Standard uae Wa Se AMES Criteria for Structural Safety of Tall Concrete Buildings Ies 91.080.040 © BIS 2017 saci ue at BUREAU OF INDIAN STANDARDS are wer, 9 aergteMe wee A, aE feet-110002 SESE iManak BHAVAN, 9 BAHADUR SHAH ZAFAR MARG NEW DELHI-1 10002 wonw.bis,orgin www. résbis.in November 2017 Price Group 10Special Structures Sectional Committee, CED 38 FOREWORD, This Indian Standard was adopted by the Bureau of Indian Standards, after the draft finalized by the Special | Structures Sectional Committee had been approved by the Civil Engineering Division Council | ‘The large scale urbanization in the country and shortage of land in urban areas for accommodating the vast population migrating thereto, is being addressed through vertical developments inthe form of tall buildings. This standard has been formulated to comprehensively address the special issues associated with the design of reinforced | conerete tal buildings, whose design is governed not just by structural safety aspects, but also by serviceability aspects, especially under the conditions of wind effects. This standard has therefore been formulated to cover these aspects celating to reinforced concrete buildings otheight greater than 50 m, but ess than or equal to 250 m. This standard provides prescriptive requirements For design of reinforced concrete tal buildings, The following salient aspects, which are based on the prescriptive approach, are addressed inthis standard 2) Stctural systems tht can be adopted in tall bullings b) General requirements including; (1) height limitations of diff@rent structural systems, (2) elevation and. plan aspect ratio, (3) lateral def (8) store sifess and stent, (5) density of buikings (6) modes of vibration, (7 floor systems, (8) materials, ind (9) progressive collapse mechanisms; ©) Wind and seismic effects: (1) load combinations, al(2) acceptable serviceability criteria for lateral accelerations, vy 4) Methods of structural analysis to bappted, ang Seton properties (in racked and uncracked sates) of reinforced concrete member to be busderedT gals, ©) Structural design aspeets for v cable structural systems; igh of foundations; and ath pgaitoring 1) Issues to be considered in d 2) Systems needed for structural Buildings that do not follow the Féquirements of this standard [for example, buildings with height exceeding the limits specified in this standart, buildingg Whose height exceeds the maximum suitable height specified for a Particular structural systemsor use of ay other (irregular) lateral load resisting steuctural system), and those buildings that are not covered by this standard, shall be deemed to be code-exceeding tall concrete buildings. Such cvode-exceeding tall concrete buildings shall require a performance-basedl design approach to demonstrate that the performance of the building meets at least that intended by the prescriptive design code provisions laid down in this standard, For such code-exceeding tall buildings, Annex A provides design and approval processes. The Committee responsible for the formulation of this standard has taken into consideration the views of users, ‘engineers, architects, builders and technologists, and has related the standard to the practices followed in the country in this field. Also, due consideration has been given to the coordination of this standard with the corresponding international standards prevailing in different regions ofthe world In the formulation of this standard, assistance has been derived from the following publications: JG) 3.2010 Technical specifications for concrete structures of tall buildings, Ministry of Housing and Urban-Rural Development of the People’s Republic of China ACI 318 — Building code requirements for structural concrete, American Concrete Institute ASCE 7-10 — Minimum design loads for buildings and other structures, American Society of Civil Engineers Academic & Science ASTM C-1202—Standard test method for electrical indication of concrete’s ability to resist chloride ion penetration, American Society for Testing and Materials EUROCODE 2-EN1992-1-1 — Design of concrete structures, European Committee for Standardization. (Continued on third cover)1s 16700 : 2017 Indian Standard CRITERIA FOR STRUCTURAL SAFETY OF TALL CONCRETE BUILDINGS 1 SCOPE, systems, for example, outrigger trusses, belt 1.1 This standard covers the following design aspects sruseos and braced frames. ofreinfored conercte (RC) buildings of heigh eater 1.6 This standard shal! be read along with all Indian than 40 m but les than or equal 10 250 m, Generally, Standards relevant to design and construction of aaa ped on prescriptive uppeoach and uilngs and structures, Tn case of conflict, clauses Covers the following design aspects of tall buildings: given in tis standard shall be applicable. 1.7 For buildings that do not conform to the prescriptive requirements of this standard, a more Figorous procedure is necessary for design and review The general procedure to be adopted is given in a). Selection of appropriate structural system; b). Geometric proportioning ofthe buildings co) Integrity of structural system; 4d) Resistance to wind and earthquake effects;and Annex A to proportion, analyze, design, detail, gain ©) Other special considerations related to tall approval and construct such buildings. Performance buildings objectives of procedures more stringent than those specified in Annex A may be specified by the elient 1.2 This standard is not applicable to tall buildings ee Baar e mae _aner ofthe building or by the tall building committee ' ve mens aN eee bo Semin local authority administering the — For the purposes ofthis stmt, nese whey uti pect Soe rea tne ecawegeis fal Oe Site nanan heme mg” 2 RERERENCES faults, ore rigorous approach is aceded to proportion gD abge @) ae re acy conte nah butiags The penpive _ TReFllowing standards contain provisions which, se ee Msonel inti sand shall Be-a88 for °4@ough reference in this text, constitute provisions of oping ih igs. race inet tne Gihis standard, A he time of publication the etions so icapeicd by th cent owner othe HulBnor by HER) A ation, We ee a ee ce appointed by thegggl aur (Op pudicated Were valid. All standards are eiest & ‘inser he bling roe. oo 7 revision, and parties to agreements based on this Standard are encouraged to investigate the possibility of applying the most recent editions ofthe standards indicated below: 1.3 This standard is applicable only Gp buildings pa house 20 00 oF Fewer persons. <> 144 This standard may alsg @rised fog Cesien of ISNo, Tule buildings of height equal.to OF tess thas $0 m. The 456:2000 Code of practive for plain and provisions ofthis standard wif value tthe design cFiforoed concrete (OA>tk RAG fsuch buildings, However this standard isnot applicable 75 Code of practice for design loads for design of buildings of height more than 250m. (other than earthquake) for buildings 1.5 This standard addresses the following typical and structure structural systems of tall concrete buildings: (Part 1): 1987 Dead loads — Unit weights of building material and stored materials a) Structural wall systems (second revision) bb) Moment frame systems; (Part 2) Imposed loads (second revision) 6) Moment frame — Structural wall systems: (Part 3) Wind loads (thind revision) (Past 4) ‘Snow loads (second revision) 4) Structural wall — Flat slab floorsystems with perimeter moment frame (Part 5) ‘Special londs and lond combinations {second revision) )_ Structural wall — Framed tube systems: 1g93 (Pen I): Criteria for earthquake resistant 1) Framedetube system: 2016 design of structures : Part 1 General 18) Tube-in-tube system: provisions and buildings (sixth revision) bh) Multiple ube system; ) Multi vst 1904 1986 Code of practice for design and i) Hybrid system; and ‘construction of foundations in soils kk) Any of the above with additional framing (ihied revision)