ANALYSIS REFERENCE Chapter 2.

Node/DOF/Coordinate
system

Section 1 Node and DOF

Nodes and elements determine the size and shape of the finite element model and are the starting point of all
analyses. A model defined by nodes and elements is the same as physical phenomena expressed using
numerical equations in matrix form. The variables that affect the matrix equation are displacement, rotation,
pore pressure and other physical quantities, which are called degrees of freedom (DOF).

For example, a structural analysis problem is assigned 3 displacements and 3 rotational DOFs. These 6 DOFs
are as follows.

Figure 2.1.1 Displacement and

2
Rotation DOFs on the rectangular
coordinate system

u2

u1 1
u3

3

Each DOF is generally expressed using the following signs:

DOF 1  T1  u1 DOF 2  T2  u2 DOF 3  T3  u3

, ,
DOF 4  R1  1 DOF 5  R2  2 DOF 6  R3  3
, ,

Each node has a coordinate system that describes the direction of motion. This is called the nodal

displacement coordinate system. All DOFs mentioned above follow the coordinate system direction

assigned to the nodes, and all nodes describe the direction of motion with reference to the global

coordinate system. The pore pressure DOF does not have a direction and hence, it is unrelated to the
nodal displacement coordinate system.

8 | Section 1. Node and DOF

 ANALYSIS REFERENCE Chapter 2. Node/DOF/Coordinate system

Section 2 Coordinate System

Various coordinate systems are needed to use the finite element method to appropriately model and correctly
analyze the given problem. For example, a coordinate system is needed to define the nodal displacement
direction outlined above and to set the direction for transversely isotropic materials. A particular coordinate
system is also specified for result value extraction. The rectangular coordinate system and cylindrical
coordinate system are both available on FEA NX.

Figure 2.2.1 Rectangular

coordinate system and cylindrical Cylindrical
Rectangular
coordinate system coordinate system
coordinate system

z
z

Origin Origin
y r
x


For example, if the nodal motion direction is defined about a cylindrical coordinate system, the DOFs are as
follows.

DOF 1 = translation in r -direction

DOF 2 = translation in  -direction
DOF 3 = translation in z -direction
DOF 4 = rotation in r -direction
DOF 5 = rotation in  -direction
DOF 6 = rotation in z -direction

FEA NX uses the following coordinate systems for ground or structural modeling and analysis.

Section 2. Coordinate System | 9

 ANALYSIS REFERENCE Chapter 2. Node/DOF/Coordinate
system

Table 2.2.1 Major coordinate Type of coordinate system Explanation

systems on the FEA NX
Coordinate system that expresses the entire model
GCS : global coordinate system using the same standard. Rectangular coordinate
system
NDCS : nodal displacement coordinate Coordinate system that describes the nodal motion
system direction. Rectangular/Cylindrical coordinate system
Coordinate system determined by the position of the
ECS : element coordinate system nodes that make up the element. Rectangular
coordinate system
Coordinate system that defines the direction of the
MCS : material coordinate system material applied on the element.
Rectangular/Cylindrical coordinate system
Coordinate system that prints the element results.
ERCS : element result coordinate system
Rectangular/Cylindrical coordinate system
Coordinate system used for finite element
EFCS : element formulation coordinate
formulation.
system
Same as GCS or element coordinate system

Here, the EFCS is used in the solver and, although it may not be directly related to the instructions for the FEA
NX, it provides a better understanding of the materials of this manual. Also, the MCS and ERCS can affect the
analysis and results. Detailed information on the ECS, MCS and ERCS are provided in Chapter 3.

Figure 2.2.2 Various coordinate

systems on the FEA NX

w
v
y z
x y
u
y x

x
z
y

GCS x

10 | Section 2. Coordinate System

 ANALYSIS REFERENCE Chapter 2. Node/DOF/Coordinate system

Section 3 Finite Rotation Simulation

Geometric nonlinear analysis that includes finite rotation needs a variable for rotation. FEA NX uses the
rotation vector as a DOF of a particular node to describe finite rotation. In other words, the result values for
nodal DOF 4~6 on the geometric nonlinear analysis results are each components of the rotation vector. The
rotation vector θ has a size θ and direction e  θ / θ . Expressing this in physical terms, the rotation vector
θ rotates about the axis e by an angle θ (radian) as shown in Figure 2.3.1

Figure 2.3.1 Direction and size of a

θ Axis of rotation
rotation vector
θ
z e
θ

y
x

Be aware that a compound rotation, which applies multiple rotation vectors continuously, does not consist of
the sum of each vector for finite rotations. For example, if a rotation of θ is continuously applied after θ , the
final rotation value θ* has a property of θ*  θ  θ . Also, because the commutative law does not apply,
applying θ and θ in reversed order creates a different rotation value, as shown in figure 2.3.2. Various
methods such as a rotation matrix can be used to calculate compound rotations, but the FEA NX uses the
quaternion product. The quaternion q has the following relationship the rotation vector θ :

q  (q0 , q)  (cos( θ / 2), sin( θ / 2)e)

(2.3.1)

The product of two quaternions can be calculated using the following equation:

q*  q q  (q0 q0  q  q, q0q  q0 q  q  q) (2.3.2)

*
q : Quaternion corresponding to θ *

q : Quaternion corresponding to θ

Section 3. Finite Rotation Simulation | 11

 ANALYSIS REFERENCE Chapter 2. Node/DOF/Coordinate
system

Figure 2.3.2 Example of θ (90) θ (90)

compound rotations that do not
satisfy the commutative law

Initial configuration Final configuration

θ (90) θ (90)

12 | Section 3. Finite Rotation Simulation