‫ روی ﻟﯾﻧﮏ زﯾر ﮐﻠﯾﮏ ﮐﻧﯾد و ﯾﺎ ﺑﮫ وﺑﺳﺎﯾت "اﯾﺑوک ﯾﺎب" ﻣراﺟﻌﮫ ﺑﻔرﻣﺎﯾﯾد‬،‫ﺑرای دﺳﺗرﺳﯽ ﺑﮫ ﻧﺳﺧﮫ ﮐﺎﻣل ﺣل اﻟﻣﺳﺎﺋل‬

Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
P1.1 A steel bar of rectangular cross section, 15 mm by 60 mm, is loaded by a compressive force of 110
kN that acts in the longitudinal direction of the bar. Compute the average normal stress in the bar.

Solution
The cross-sectional area of the steel bar is
A  15 mm  60 mm   900 mm2
The normal stress in the bar is
F 110 kN 1,000 N/kN 
   122.222 MPa  122.2 MPa Ans.
A 900 mm2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.2 A circular pipe with outside diameter of 4.5 in. and wall thickness of 0.375 in. is subjected to an
axial tensile force of 42,000 lb. Compute the average normal stress in the pipe.

Solution
The outside diameter D, the inside diameter d, and the wall thickness t are related by
D  d  2t
Therefore, the inside diameter of the pipe is
d  D  2t  4.5 in.  2  0.375 in.  3.75 in.
The cross-sectional area of the pipe is
 
A
4
D 2
 d2 
4
 4.5 in.   3.75 in.   4.8597 in.2
2

2

The average normal stress in the pipe is

F 42,000 lb
   8,642.6 psi  8,640 psi Ans.
A 4.8597 in.2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.3 A circular pipe with an outside diameter of 80 mm is subjected to an axial compressive force of
420 kN. The average normal stress may not exceed 130 MPa. Compute the minimum wall thickness
required for the pipe.

Solution
From the definition of normal stress, solve for the minimum area required to support a 420 kN load
without exceeding a normal stress of 130 MPa
F F  420 kN 1,000 N/kN 
  Amin    3,230.77 mm2
A  130 N/mm 2

The cross-sectional area of the pipe is given by


A (D2  d 2 )
4
Set this expression equal to the minimum area and solve for the maximum inside diameter d

80 mm   d 2   3, 230.77 mm2
2

4 

80 mm   d 2   3, 230.77 mm2 

2 4

 d max  47.8169 mm

The outside diameter D, the inside diameter d, and the wall thickness t are related by
D  d  2t
Therefore, the minimum wall thickness required for the aluminum tube is
D  d 80 mm  47.8169 mm
tmin    16.092 mm  16.09 mm Ans.
2 2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

P1.4 Three solid bars, each with square cross sections, make up the axial assembly shown in Figure
P1.4/5. Two loads of P = 30 kN are applied to the assembly at flange B, two loads of Q = 18 kN are
applied at C, and one load of R = 42 kN is applied at end D. The bar dimensions are b1 = 60 mm, b2 =
20 mm, and b3 = 40 mm. Determine the normal stress in each bar.

FIGURE P1.4/5

Solution
Cut an FBD through bar (1). The FBD should include the free end of the assembly at D. We will
assume that the internal force in bar (1) is tension. From equilibrium, the force in bar (1) is
Fx   F1  2 P  2Q  R  0
 F1  2 P  2Q  R  2  30 kN   2 18 kN   42 kN  66 kN  66 kN (C)

From the given width of bar (1), the cross-sectional area of bar (1) is
A1  b12   60 mm   3,600 mm2
2

and thus, the normal stress in bar (1) is

F  66 kN 1,000 N/kN 
1  1   18.333 MPa  18.33 MPa (C) Ans.
A1 3,600 mm2

Cut an FBD through bar (2). The FBD should include the free end of the assembly at D. We will
assume that the internal force in bar (2) is tension. From equilibrium, the force in bar (2) is
Fx   F2  2Q  R  0
 F2  2Q  R  2 18 kN   42 kN  6 kN  6 kN (C)

From the given width of bar (2), the cross-sectional area of bar (2) is
A2  b22   20 mm   400 mm2
2

The normal stress in bar (2) is

https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

F2  6 kN 1,000 N/kN 
2    15.000 MPa  15.00 MPa (C) Ans.
A2 400 mm2

Cut an FBD through bar (3). The FBD should include the free end of the assembly at D. We will
assume that the internal force in bar (3) is tension. From equilibrium, the force in bar (3) is
Fx   F3  R  0
 F3   R  42 kN  42 kN (C)

The cross-sectional area of bar (3) is

A3  b32   40 mm   1,600 mm2
2

The normal stress in bar (3) is

F  42 kN 1, 000 N/kN 
2  2   26.250 MPa  26.3 MPa (C) Ans.
A2 1, 600 mm2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

P1.5 Three solid bars, each with square cross sections, make up the axial assembly shown in Figure
P1.4/5. Two loads of P = 25 kN are applied to the assembly at flange B, two loads of Q = 15 kN are
applied at C, and one load of R = 35 kN is applied at end D. Bar (1) has a width of b1 = 90 mm.
Calculate the width b2 required for bar (2) if the normal stress magnitude in bar (2) must equal the
normal stress magnitude in bar (1).

FIGURE P1.4/5

Solution
Cut an FBD through bar (1). The FBD should include the free end of the assembly at D. We will
assume that the internal force in bar (1) is tension. From equilibrium, the force in bar (1) is
Fx   F1  2 P  2Q  R  0
 F1  2 P  2Q  R  2  25 kN   2 15 kN   35 kN  55 kN  55 kN (C)

From the given width of bar (1), the cross-sectional area of bar (1) is
A1  b12   90 mm   8,100 mm2
2

and thus, the normal stress in bar (1) is

F  55 kN 1, 000 N/kN 
1  1   6.7901 MPa
A1 8,100 mm2

Cut an FBD through bar (2). The FBD should include the free end of the assembly at D. We will
assume that the internal force in bar (2) is tension. From equilibrium, the force in bar (2) is
Fx   F2  2Q  R  0
 F2  2Q  R  2 15 kN   35 kN  5 kN

The normal stress in bar (2) must equal the normal stress in bar (1). Thus,
 2  1  6.7901 MPa
Solve for the required area of bar (2):
 Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
F2
2 
A2
F2  5 kN 1, 000 N/kN 
 A2   736.364 mm 2
2 6.7901 N/mm 2

The width of bar (2) is therefore:

b2  736.364 mm2  27.136 mm  27.1 mm Ans.
 Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
P1.6 Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in Figure
P1.6/7. One load of P = 1,500 lb is applied to the assembly at A, two loads of Q = 900 lb are applied
at B, and two loads of R = 1,300 lb are applied at C. The diameters of rods (1), (2), and (3) are d1 =
0.625 in., d2 = 0.500 in., and d3 = 0.875 in. Determine the axial normal stress in each of the three rods.

FIGURE P1.6/7

Solution
Cut an FBD through rod (1). The FBD should include the free end of the assembly at A. We will
assume that the internal force in rod (1) is tension. From equilibrium, the force in rod (1) is
Fx   P  F1  0
 F1  P  1,500 lb  1,500 lb (T)

Use the given diameter to calculate the cross-sectional area of rod (1):
 
A1  d12   0.625 in.  0.3068 in.2
2

4 4
The normal stress in rod (1) is
F 1,500 lb
1  1   4,889.24 psi  4,890 psi (T) Ans.
A1 0.3068 in.2

Cut an FBD through rod (2). The FBD should include the free end of the assembly at A. We will
assume that the internal force in rod (2) is tension. From equilibrium, the force in rod (2) is
Fx   P  2Q  F2  0
 F2  P  2Q  1,500 lb  2  900 lb   300 lb  300 lb (C)

Use the given diameter to calculate the cross-sectional area of rod (2):
 
A2  d22   0.500 in.  0.1963 in.2
2

4 4
The normal stress in rod (2) is
F 300 lb
2  2   1,527.89 psi  1,528 psi (C) Ans.
A2 0.1963 in.2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

Cut an FBD through rod (3). The FBD should include the free end of the assembly at A. We will
assume that the internal force in rod (3) is tension. From equilibrium, the force in rod (3) is
Fx   P  2Q  2 R  F3  0
 F3  P  2Q  2 R  1,500 lb  2  900 lb   2 1,300 lb   2,300 lb  2,300 lb (T)

Use the given diameter to calculate the cross-sectional area of rod (3):
 
A3  d32   0.8750 in.  0.6013 in.2
2

4 4
The normal stress in rod (3) is
F 2,300 lb
3  3   3,824.92 psi  3,820 psi (T) Ans.
A3 0.6013 in.2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.7 Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in Figure
P1.6/7. One load of P = 30 kips is applied to the assembly at A, two loads of Q = 25 kips are applied
at B, and two loads of R = 35 kips are applied at C. The normal stress magnitude in aluminum rod (1)
must be limited to 20 ksi. The normal stress magnitude in steel rod (2) must be limited to 35 ksi. The
normal stress magnitude in brass rod (3) must be limited to 25 ksi. Determine the minimum diameter
required for each of the three rods.

FIGURE P1.6/7

Solution
Cut an FBD through aluminum rod (1). The FBD should include the free end of the assembly at A.
We will assume that the internal force in rod (1) is tension. From equilibrium, the force in rod (1) is
Fx   P  F1  0
 F1  P  30 kips  30 kips (T)

The normal stress magnitude in aluminum rod (1) must be limited to 20 ksi. Therefore, the minimum
cross-sectional area of rod (1) must be
F 30 kips
A1  1   1.500 in.2
1 20 ksi
The diameter must be

A1  d12
4

 d1 
4

1.500 in.   1.382 in.
2
Ans.

Cut an FBD through steel rod (2). The FBD should include the free end of the assembly at A. We
will assume that the internal force in rod (2) is tension. From equilibrium, the force in rod (2) is
Fx   P  2Q  F2  0
 F2  P  2Q  30 kips  2  25 kips   20 kips  20 kips (C)
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

The normal stress magnitude in steel rod (2) must be limited to 35 ksi. Therefore, the minimum cross-
sectional area of rod (2) must be
F 20 kips
A2  2   0.5714 in.2
2 35 ksi
The diameter of rod (2) must be

A2  d 22
4

 d2 
4

 0.5714 in.   0.853 in.
2
Ans.

Cut an FBD through brass rod (3). The FBD should include the free end of the assembly at A. We
will assume that the internal force in rod (3) is tension. From equilibrium, the force in rod (3) is
Fx   P  2Q  2 R  F3  0
 F3  P  2Q  2 R  30 kips  2  25 kips   2  35 kips   50 kips  50 kips (T)

The normal stress magnitude in brass rod (3) must be limited to 25 ksi. Therefore, the minimum
cross-sectional area of rod (3) must be
F 50 kips
A3  3   2.0000 in.2
3 25 ksi
The diameter of rod (3) must be

A3  d32
4

 d3 
4

 2.0000 in.   1.596 in.
2
Ans.
 Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
P1.8 Determine the normal stress in rod (1) for the
mechanism shown in Figure P1.8. The diameter of
rod (1) is 8 mm, and load P = 2,300 N. Use the
following dimensions: a = 120 mm, b = 200 mm, c =
170 mm, and d = 90 mm.

FIGURE P1.8

Solution
First, consider an FBD of the pulley to determine the reaction forces exerted on the pulley by the
mechanism.
Fx  Ax  P  P cos  60   0
 Ax   2,300 N    2,300 N  cos  60   3, 450.000 N
Fy  Ay  P sin  60   0
 Ay   2,300 N  sin  60   1,991.858 N

FBD of pulley FBD of mechanism

Next, consider an FBD of the mechanism to determine the force in rod (1). Rod (1) is oriented at an
angle of:
c  d 170 mm  90 mm
tan     1.30
b 200 mm
   52.431
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

Rod (1) is a two-force member, and its axial force can be calculated from:
M C  Ax c  Ay a   F1 cos   c  d   0

 F1 
Ax c  Ay a  3, 450.000 N 170 mm   1,991.858 N 120 mm   5, 207.523 N

 c  d  cos  170 mm  90 mm  cos 52.431
The area of rod (1) is
 
A1  d12  8 mm   50.265 mm2
2

4 4

The normal stress in the rod is thus

F 5, 207.532 N
1  1 =  103.601 MPa  103.6 MPa Ans.
A1 50.265 mm2
 Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
P1.9 Determine the normal stress in bar (1) for the
mechanism shown in Figure P1.9. The area of bar
(1) is 2,600 mm2. The distributed load intensities
are wC = 12 kN/m and wD = 30 kN/m. Use the
following dimensions: a = 7.5 m and b = 3.0 m.

FIGURE P1.9

Solution
Consider an FBD of the mechanism. Determine the angle
 between rod (1) and the horizontal axis:
a 7.5 m
tan     2.5
b 3.0 m
   68.199

Write an equilibrium equation for the sum of moments

about C to compute the force in bar (1). Note: Bar (1) is a
two-force member.
wC a a wD a 2a
M C   F1 sin   b     0
2 3 2 3
wC a 2 2wD a 2
   12 kN/m  2  30 kN/m  
 
2
a 2
w  2 w 7.5 m
 F1  6 6  C D
  242.332 kN
b sin  6b sin  6  3.0 m  sin  68.199 

The normal stress in bar (1) is thus:

F (242.332 kN)(1,000 N/kN)
1  1  2
 93.205 N/mm2  93.2 MPa (T) Ans.
A1 2,600 mm
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.10 The rigid beam BC shown in Figure P1.10 is

supported by rods (1) and (2) that have diameters of
0.875 in. and 1.125 in., respectively. For a uniformly
distributed load of w = 4,200 lb/ft, determine the
normal stress in each rod. Assume L = 14 ft and a = 9
ft.

FIGURE P1.10

Solution
Equilibrium: Calculate the internal forces in rods (1) and (2).
 9 ft 
M C   F1 14 ft    4, 200 lb/ft  9 ft   0
 2 
 F1  12.150 kips
 9 ft 
M B  F2 14 ft    4, 200 lb/ft  9 ft  14 ft  0
 2 
 F2  25.650 kips

Areas:

A1   0.875 in.  0.601 in.2
2

4

A2  1.125 in.  0.994 in.2
2

Stresses:
F1 12.150 kips
1    20.206 ksi  20.2 ksi Ans.
A1 0.601 in.2

F2 25.650 kips
2    25.804 ksi  25.8 ksi Ans.
A2 0.994 in.2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.11 The rigid beam ABC shown in Figure P1.11 is

supported by a pin connection at C and by steel rod
(1), which has a diameter of 10 mm. If the normal
stress in rod (1) must not exceed 225 MPa, what is the
maximum uniformly distributed load w that may be
applied to beam ABC? Use dimensions of a = 340
mm, b = 760 mm, and c = 550 mm.

FIGURE P1.11

Solution
The cross-sectional area of rod (1) is

A1  10 mm   78.540 mm2
2

4
Since the normal stress in rod (1) must not exceed 225 MPa, the allowable force that can be applied to
rod (1) is:
F1,allow  1 A1   225 N/mm2  78.540 mm2   17,671.459 N
Rod (1) is oriented at an angle of  with respect to the horizontal direction:
c 550 mm
tan     0.7237    35.893
b 760 mm

Consider an FBD of rigid beam ABC. From the moment

equilibrium equation about joint C, the relationship
between the force in rod (1) and the distributed load w is:
 ab
M C  w  a  b      F1 sin   b  0
 2 
2b  F1 sin  
w 
 a  b
2

Substitute the allowable force F1,allow into this relationship to obtain the maximum distributed load that
may be applied to the structure:
2b  F1 sin  
w
 a  b
2

2  760 mm 17, 671.459 N  sin  35.893 


 340 mm  760 mm 
2

 13.014 N/mm  13.01 kN/m Ans.

https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.12 A simple pin-connected truss is loaded

and supported as shown in Figure P1.12. The
load P is 200 kN. All members of the truss
are aluminum pipes that have an outside
diameter of 115 mm and a wall thickness of 6
mm. Determine the normal stress in each truss
member. Assume truss dimensions of a =
12.0 m, b = 7.5 m, and c = 6.0 m.

FIGURE P1.12

Solution
Overall equilibrium:
Begin the solution by determining the external
reaction forces acting on the truss at supports B
and D. Write equilibrium equations that include
all external forces. Note that only the external
forces (i.e., loads and reaction forces) are
considered at this time. The internal forces acting
in the truss members will be considered after the
external reactions have been computed. The free-
body diagram (FBD) of the entire truss is shown.
The following equilibrium equations can be
written for this structure:
Fy  Dy  P  0 
 Dy  P  200 kN
M D  Pa  Bx c  0
Pa P 12 m 
 Bx     2 P  400 kN
c 6m
M B  Pa  Dx c  0
Pa P 12 m 
 Dx    2 P  400 kN
c 6m

Method of joints:
Before beginning the process of determining the internal forces in the axial members, the geometry of
the truss will be used to determine the magnitude of the inclination angles of members AC and BC. Use
the definition of the tangent function to determine AC and BC:
c 6.0 m
tan  AC    1.3333  AC  53.130
a  b 12.0 m  7.5 m
c 6.0 m
tan  BC    0.8  BC  38.660
b 7.5 m
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

Joint A:
Begin the solution process by considering an FBD of joint A.
Consider only those forces acting directly on joint A. In this
instance, two axial members, AB and AC, are connected at joint A.
Tension forces will be assumed in each truss member.
Fx  FAB  FAC cos AC  0 (a)
Fy  FAC sin  AC  P  0 (b)
Solve Eq. (b) for FAC:
P 200 kN
FAC    250.0 kN
sin  AC sin  53.130 
and then compute FAB using Eq. (a):
FAB   FAC cos  AC
   250.0 kN  cos  53.130   150.0 kN

Joint D:
Next, consider an FBD of joint D. As before, tension forces will be
assumed in each truss member.
Fx  Dx  FCD  0 (c)
Fy  Dy  FBD  0 (d)

Solve Eq. (c) for FCD:

FCD  Dx  400.0 kN
and solve Eq. (d) for FBD:
FBD  Dy  200.0 kN

Joint C:
Next, consider an FBD of joint C. As before, tension forces will be
assumed in each truss member.
Fx  FCD  FBC cos BC  FAC cos AC  0 (e)
Fy   FBC sin  BC  FAC sin  AC  0 (f)
Solve Eq. (e) for FBC:
sin  AC sin  53.130 
FBC   FAC    250 kN   320.1562 kN
sin  BC sin  38.660 
Eq. (f) can be used as a check on our calculations:
Fy   FBC sin  BC  FAC sin  AC
   320.1562 kN  sin  38.660    250.0 kN  sin  53.130   0 Checks!
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

Section properties:
For each of the five truss members:

d  115 mm  2  6 mm   103 mm A 115 mm   103 mm    2, 054.602 mm2
2 2

4 

Normal stress in each truss member:

F
 AB  AB 
 150 kN 1,000 N/kN   73.007 MPa  73.0 MPa (C) Ans.
AAB 2, 054.602 mm2
F
 AC  AC 
 250.0 kN 1,000 N/kN   121.678 MPa  121.7 MPa (T) Ans.
AAC 2, 054.602 mm2
F
 BC  BC 
 320.156 kN 1,000 N/kN   155.824 MPa  155.8 MPa (C) Ans.
ABC 2, 054.602 mm2
F
 BD  BD 
 200.0 kN 1,000 N/kN   97.342 MPa  97.3 MPa (T) Ans.
ABD 2, 054.602 mm2
F
 CD  CD 
 400.0 kN 1,000 N/kN   194.685 MPa  194.7 MPa (T) Ans.
ACD 2, 054.602 mm2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.13 A horizontal load P is applied to an assembly

consisting of two inclined bars, as shown in Figure 1.13.
The cross-sectional area of bar (1) is 1.5 in.2, and the
cross-sectional area of bar (2) is 1.8 in.2. The normal
stress in either bar may not exceed 24 ksi. Determine the
maximum load P that may be applied to this assembly.
Assume dimensions of a = 16 ft, b = 8 ft, and c = 13 ft.

FIGURE P1.13

Solution
Allowable member forces:
Using the allowable stresses and the member areas, we can determine the allowable force for each
member:
F1,allow  1,allow A1   24 ksi  1.5 in.2   36 kips (a)
F2,allow   2,allow A2   24 ksi  1.8 in.2   43.2 kips (b)

Equilibrium:
The geometry of the two-bar assembly will be used to determine the magnitude of the inclination angles
for members AB and BC. We can use the definition of the tangent function to determine AB and BC:
a 16 ft
tan  AB    1.2308  AB  50.906
c 13 ft
b 8 ft
tan  BC    0.6154  BC  31.608
c 13 ft

Consider a free-body diagram (FBD) of joint B. The following

equilibrium equations can be written for this joint:
Fx  P  F1 cos  AB  F2 cos  BC  0 (c)
Fy  F1 sin  AB  F2 sin  BC  0 (d)


Erroneous approach for finding maximum load P:

Since we are trying to calculate P, the temptation at this point in the solution is to substitute the values
from Equations (a) and (b) into Eq. (c) and simply solve for P:
P  F1 cos  AB  F2 cos  BC
  36 kips  cos  50.906    43.2 kips  cos  31.608 
 59.493 kips (e)
However, if we use the values from Equations (a) and (b) in Eq. (d), we find that equilibrium is not
satisfied:
Fy  F1 sin  AB  F2 sin  BC
  36 kips  sin  50.906    43.2 kips  sin  31.608 
 5.299 kips  0
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

Equilibrium must always be satisfied; therefore, we must conclude that F1 and F2 will not have the
allowable values of Equations (a) and (b). The answer obtained in Eq. (e) is incorrect because
equilibrium is not satisfied.

Correct method for calculating the capacity of the two-bar assembly:

The allowable load that can be applied to this two-bar assembly will be the load P that produces the
allowable load in either member (1) or member (2). Let’s return to Eq. (d), only this time, we are going
to make an assumption. We will assume that the force in member (1) will control the capacity of the
two-bar assembly. If this assumption is true, then the force in member (1) will equal its allowable force
as given in Eq. (a), and the force in member (2) will be less than its allowable force as given in Eq. (b).
sin  AB sin  50.906 
F2  F1  F1  1.4809 F1
sin  BC sin  31.608 
 1.4809  36 kips 
 53.311 kips  F2,allow  43.2 kips N.G.
This calculation shows that the force in member (2) will exceed its allowable force when the force in
member (1) equals its allowable force. Therefore, our assumption is proved incorrect. This result shows
us that the force in member (2) will control the capacity of the two-bar assembly. We’ll return to Eq.
(d), only this time, we know that member (2) will control. Set the force in member (2) to its allowable
force from Eq. (b) and solve for the force in member (1) that is required to satisfy equilibrium.
sin  BC sin  31.608 
F1  F2  F2  0.6753F2
sin  AB sin  50.906 
 0.6753  43.2 kips 
 29.172 kips  F1,allow  36 kips O.K.

We now know the forces in members (1) and (2) that will satisfy the equilibrium equations without
exceeding the allowable force in either member. Finally, we use these values to determine the load P
from Eq. (c):
P  F1 cos  AB  F2 cos  BC
  29.172 kips  cos  50.906    43.2 kips  cos  31.608 
 55.188 kips
= 55.2 kips Ans.
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.14 The rectangular bar shown in Figure

P1.14 is subjected to a uniformly distributed
axial loading of w = 13 kN/m and a
concentrated force of P = 9 kN at B.
Determine the magnitude of the maximum
normal stress in the bar and its location x.
Assume a = 0.5 m, b = 0.7 m, c = 15 mm, and
d = 40 mm.
FIGURE P1.14

Solution
Equilibrium:
Draw an FBD for the interval between A and B where
0  x  a . Write the following equilibrium equation:


Fx  (13 kN/m)(1.2 m  x)  (9 kN)  F  0
 F  (13 kN/m)(1.2 m  x)  (9 kN)
The largest force in this interval occurs at x = 0 where F = 6.6
kN.

In the interval between B and C where a  x  a  b , and write

the following equilibrium equation:


Fx  (13 kN/m)(1.2 m  x)  F  0
 F  (13 kN/m)(1.2 m  x)
The largest force in this interval occurs at x = a where F = 9.1
kN.

Maximum Normal Stress:

(9.1 kN)(1,000 N/kN)
 max   15.17 MPa at x  0.5 m Ans.
(15 mm)(40 mm)
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.15 The solid 1.25 in. diameter rod shown in

Figure P1.15 is subjected to a uniform axial
distributed loading along its length of w = 750 lb/ft.
Two concentrated loads also act on the rod: P =
2,000 lb and Q = 1,000 lb. Assume a = 16 in. and b
= 32 in. Determine the normal stress in the rod at
the following locations:
(a) x = 10 in.
(b) x = 30 in.
FIGURE P1.15

Solution
(a) x = 10 in.
Equilibrium: Draw an FBD for the interval between A and B
where 0  x  a , and write the following equilibrium equation:


 Fx  (750 lb/ft)(1 ft/12 in.)(48 in.  x)
 (2,000 lb)  (1,000 lb)  F  0
 F  (62.5 lb/in.)(48 in.  x)  3,000 lb
At x = 10 in., F = 5,375 lb.

Stress: The normal stress at this location can be calculated as follows.


A (1.25 in.) 2  1.227185 in.2
4
5,375 lb
  4,379.944 psi  4,380 psi Ans.
1.227185 in.2

(b) x = 30 in.
Equilibrium: Draw an FBD for the interval between B and C
where a  x  a  b , and write the following equilibrium
equation:


 Fx  (750 lb/ft)(1 ft/12 in.)(48 in.  x)
 (1,000 lb)  F  0
 F  (62.5 lb/in.)(48 in.  x)  1,000 lb
At x = 30 in., F = 2,125 lb.

Stress: The normal stress at this location can be calculated as follows.

2,125 lb
  1,731.606 psi  1,730 psi Ans.
1.227185 in.2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

P1.16 A block of wood is tested in direct shear using the

test fixture shown below. The dimensions of the test
specimen are a = 3.75 in., b = 1.25 in., c = 2.50 in., and d
= 6.0 in. During the test, a load of P = 1,590 lb produces
a shear failure in the wood specimen. What is the
magnitude of the average shear stress in the wood
specimen at failure?

FIGURE P1.16

Solution
Visualize the surface that will be exposed when the specimen fails.
The area of this surface will be
AV  cd   2.50 in. 6.0 in.  15.0 in.2

The average shear stress in the specimen at failure is thus

P 1,590 lb
 avg    106.0 psi Ans.
AV 15.0 in.2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.17 A cylindrical rod of diameter d =

0.625 in. is attached to a plate by a
cylindrical rubber grommet. The plate
has a thickness of t = 0.875 in. If the
axial load on the rod is P = 175 lb, what
is the average shear stress on the
cylindrical surface of contact between
the rod and the grommet?

FIGURE P1.17

Solution
Visualize the contact surface between the rod and the grommet. It will be a cylinder with a diameter of
d and a height of t. The area of this cylinder will be
AV   dt    0.625 in. 0.875 in.  1.718 in.2

The average shear stress between the rod and the grommet is thus
P 175 lb
 avg    101.9 psi Ans.
AV 1.718 in.2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.18 Two wood boards, each 19 mm thick,

are joined by the glued finger joint shown in
Figure P1.18. The finger joint will fail when
the average shear stress in the glue reaches
940 kPa. Determine the shortest allowable
length d of the cuts if the joint is to
withstand an axial load of P = 5.5 kN. Use
a = 23 mm and b = 184 mm.

FIGURE P1.18

Solution
We are considering the shear strength of the glued joint. The minimum shear area that is required for
this connection can be determined from the load P and the shear strength of the glue. Consequently, we
will need at least this much area
P  5.5 kN 1, 000 N/kN 
AV ,min    5,851.064 mm2
 0.940 N/mm2
to transmit the load P through the joint, based on the shear strength of the glue.

For this particular joint, there are seven surfaces that will be glued. Each of these surfaces has a length
of d and a thickness of 19 mm. Accordingly, the minimum length d required for each of the finger joints
is
7dt  5,851.064 mm 2
5,851.064 mm 2
d   44.0 mm Ans.
7 19 mm 
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.19 For the connection shown in Figure P1.19,

determine the average shear stress produced in the 7/8 in.
diameter bolts if the applied load is P = 32,000 lb.

FIGURE P1.19

Solution
There are three bolts, and it is always assumed that each bolt supports an equal portion of the external
load P. Therefore, the shear force V carried by each bolt is
32, 000 lb
V  10, 666.667 lb
3 bolts
The bolts in this connection act in single shear. The cross-sectional area of a single bolt is
  
Abolt  2
dbolt  (7 / 8 in.)2 
(0.875 in.)2  0.6013 in.2
4 4 4
Therefore, the average shear stress in each bolt is
V 10, 666.667 lb
   17, 738.739 psi  17, 740 psi Ans.
Abolt 0.6013 in.2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.20 For the clevis connection shown in

Figure P1.20, determine the maximum
applied load P that can be supported by the
15 mm diameter pin if the average shear
stress in the pin must not exceed 130 MPa.

FIGURE P1.20

Solution
Consider an FBD of the bar that is connected by the clevis,
including a portion of the pin. If the shear force acting on
each exposed surface of the pin is denoted by V, then the
shear force on each pin surface is related to the load P by:
Fx  P  V  V  0  P  2V

The area of the pin surface exposed by the FBD is simply the cross-sectional area of the pin:
 
Apin  2
dpin  (15 mm)2  176.715 mm2
4 4

If the average shear stress in the pin must be limited to 130 MPa, the maximum shear force V on a single
cross-sectional surface must be limited to
V   Abolt  130 N/mm2 176.715 mm2   22,972.95 N

Therefore, the maximum load P that may be applied to the connection is

P  2V  2  22,972.95 N   45,945.9 N  45.9 kN Ans.
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

P1.21 The five-bolt connection shown in Figure P1.21 must

support an applied load of P = 160 kips. If the average shear stress
in the bolts must be limited to 30 ksi, what is the minimum bolt
diameter that may be used for this connection?

FIGURE P1.21

Solution
There are five bolts, and it is assumed that each bolt supports an equal portion of the external load P.
Therefore, the shear force carried by each bolt is
160 kips
V  32 kips
5 bolts
Since the average shear stress must be limited to 30 ksi, each bolt must provide a shear area of at least:
32 kips/bolt
AV   1.0667 in.2 /bolt
30 ksi
Each bolt in this connection acts in double shear; therefore, two cross-sectional bolt surfaces are
available to transmit shear stress in each bolt.
AV 1.0667 in.2 /bolt
Abolt    0.5333 in.2 per bolt surface
2 surfaces per bolt 2 surfaces/bolt
The minimum bolt diameter must be
 2
dbolt  0.5333 in.2  dbolt  0.824 in. Ans.
4
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.22 The handle shown in Figure P1.22 is

attached to a 40 mm diameter shaft with a
square shear key. The forces applied to the
lever are P = 1,300 N. If the average shear
stress in the key must not exceed 150 MPa,
determine the minimum dimension a that must
be used if the key is 25 mm long. The overall
length of the handle is L = 0.70 m.
FIGURE P1.22

Solution
To determine the shear force V that must be resisted by the shear key, sum moments about the center of
the shaft (which will be denoted O):
 700 mm   700 mm   40 mm 
M O  (1,300 N)    (1,300 N)    V  0
 2   2   2 
V  45,500 N
Since the average shear stress in the key must not exceed 150 MPa, the shear area required is
V 45,500 N
AV    303.3333 mm2
 150 N/mm 2

The shear area in the key is given by the product of its length L (i.e., 25 mm) and its width a. Therefore,
the minimum key width a is
AV 303.3333 mm2
a   12.1333 mm  12.13 mm Ans.
L 25 mm
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.23 An axial load P is supported by the short steel

column shown in Figure P1.23. The column has a cross-
sectional area of 14,500 mm2. If the average normal stress
in the steel column must not exceed 75 MPa, determine the
minimum required dimension a so that the bearing stress
between the base plate and the concrete slab does not
exceed 8 MPa. Assume b = 420 mm.

FIGURE P1.23

Solution
Since the normal stress in the steel column must not exceed 75 MPa, the maximum column load is
Pmax   A  (75 N/mm2 )(14,500 mm2 )  1,087,500 N
The maximum column load must be distributed over a large enough area so that the bearing stress
between the base plate and the concrete slab does not exceed 8 MPa; therefore, the minimum plate area
is
P 1,087,500 N
Amin    135,937.5 mm2
b 8 N/mm2
The area of the plate is a ×b. Since b = 420, the minimum length of a must be
Amin  135,937.5 mm 2  a  b
135,937.5 mm 2
a   324 mm Ans.
420 mm
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

P1.24 The two wooden boards shown in Figure P1.24 are

connected by a 0.5 in. diameter bolt. Washers are installed
under the head of the bolt and under the nut. The washer
dimensions are D = 2 in. and d = 5/8 in. The nut is tightened
to cause a tensile stress of 9,000 psi in the bolt. Determine
the bearing stress between the washer and the wood.

FIGURE P1.24

Solution
The tensile stress in the bolt is 9,000 psi; therefore, the tension force that acts in the bolt is

Fbolt   bolt Abolt  (9,000 psi) (0.5 in.)2  (9,000 psi)(0.196350 in.2 )  1,767.146 lb
4
The contact area between the washer and the wood is

Awasher  (2 in.)2  (0.625 in.)2   2.834796 in.2
4
Thus, the bearing stress between the washer and the wood is
1,767.146 lb
b   623 psi Ans.
2.834796 in.2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.25 For the beam shown in Figure P1.25, the

allowable bearing stress for the material under
the supports at A and B is b = 800 psi.
Assume w = 2,100 lb/ft, P = 4,600 lb, a = 20 ft,
and b = 8 ft. Determine the size of square
bearing plates required to support the loading
shown. Dimension the plates to the nearest ½
in.
FIGURE P1.25

Solution
Equilibrium: Using the FBD shown,
calculate the beam reaction forces.
 20 ft 
M A  By (20 ft)  (2,100 lb/ft)(20 ft)   (4,600 lb)(28 ft)  0
 2 
 By  27,440 lb

 20 ft 
M B   Ay (20 ft)  (2,100 lb/ft)(20 ft)   (4,600 lb)(8 ft)  0
 2 
 Ay  19,160 lb

Bearing plate at A: The area of the bearing plate required for support A is
19,160 lb
AA   23.950 in.2
800 psi
Since the plate is to be square, its dimensions must be
width  23.950 in.2  4.894 in. use 5 in.  5 in. bearing plate at A Ans.

Bearing plate at B: The area of the bearing plate required for support B is
27,440 lb
AB   34.300 in.2
800 psi
Since the plate is to be square, its dimensions must be
width  34.300 in.2  5.857 in. use 6 in.  6 in. bearing plate at B Ans.
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.26 A wood beam rests on a square post.

The vertical reaction force of the beam at the
post is P = 1,300 lb. The square post has
cross-sectional dimensions of a = 6.25 in. The
beam has a width of b = 1.50 in. and a depth of
d = 7.50 in. What is the average bearing stress
in the wood beam?

FIGURE P1.26

Solution
Contact area: Visualize the contact area between the beam and the post. The contact area is
Ab  ab   6.25 in.1.50 in.  9.375 in.2

Bearing stress: The average bearing stress in the wood beam is

P 1,300 lb
b    138.7 psi Ans.
Ab 9.375 in.2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.27 The pulley shown in Figure P1.27 is

connected to a bracket with a circular pin of
diameter d = 6 mm. Each vertical side of the
bracket has a width of b = 25 mm and a
thickness of t = 4 mm. If the pulley belt
tension is P = 570 N, what is the average
bearing stress produced in the bracket by the
pin?

FIGURE P1.27

Solution
Pulley FBD: Consider an FBD of the pulley with the belt tensions.
From equilibrium, the bracket exerts horizontal and vertical reaction
forces Rx and Ry, respectively, on the pulley.
Fx  Rx  P cos  30   0
 Rx  P cos  30    570 N  cos  30   493.634 N
Fy  Ry  P  P sin  30   0
 Ry   P  P sin  30   570 N   570 N  sin  30   855.0 N

The resultant force exerted on the pulley by the bracket is thus

R  Rx2  Ry2

  493.634 N    855.0 N 
2 2

 987.269 N

Bearing stress in the bracket: From Newton’s Third Law, the pulley pin exerts an equal force R on the
bracket. The bracket has two vertical pieces (i.e., a plate on each side of the pulley). The resultant force
R is divided equally between these two vertical pieces. Therefore, the force exerted by the pin on one of
the vertical bracket pieces is 493.635 N. The average bearing stress in the bracket is based on the
projected area of the pin. Therefore, the average bearing stress produced in the bracket by the pin is
R/2 R/2 493.635 N
b     20.568 MPa  20.6 MPa Ans.
Ab dt  6 mm  4 mm 
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

P1.28 The d = 15 mm diameter solid rod shown in

Figure P1.28 passes through a D = 20 mm diameter
hole in the support plate. When a load P is applied
to the rod, the rod head rests on the support plate.
The support plate has a thickness of b = 12 mm.
The rod head has a diameter of a = 30 mm and the
head has a thickness of t = 10 mm. If the normal
stress produced in the rod by load P is 225 MPa,
determine:
(a) the average bearing stress acting between the
support plate and the rod head.
(b) the average shear stress produced in the rod
head.
(c) the punching shear stress produced in the
support plate by the rod head.

FIGURE P1.28

Solution
The cross-sectional area of the rod is:

Arod  (15 mm)2  176.715 mm2
4
The tensile stress in the rod is 225 MPa; therefore, the tension force in the rod is
Frod   rod Arod  (225 N/mm2 )(176.715 mm2 )  39,760.782 N

(a) The contact area between the support plate and the rod head is

Acontact  (30 mm)2  (20 mm)2   392.699 mm2
4
Thus, the bearing stress between the support plate and the rod head is
39,760.782 N
b   101.3 MPa Ans.
392.699 mm2

(b) In the rod head, the area subjected to shear stress is equal to the perimeter of the rod times the
thickness of the head.
AV   (15 mm)(10 mm)  471.239 mm2
and therefore, the average shear stress in the rod head is
39,760.782 N
  84.4 MPa Ans.
471.239 mm2

(c) In the support plate, the area subjected to shear stress is equal to the product of the rod head
perimeter and the thickness of the plate.
AV   (30 mm)(12 mm)  1,130.973 mm2
and therefore, the average punching shear stress in the support plate is
39,760.782 N
  35.2 MPa Ans.
1,130.973 mm2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

P1.29 A hollow box beam ABCD is supported at A by a pin that passes through the beam as shown
in Figure P1.29. The box beam is also supported by a roller that is located at B. The beam
dimensions are a = 2.5 ft, b = 5.5 ft, and c = 3.5 ft. Two equal concentrated loads of P = 2,750 lb
are placed on the box beam at points C and D. The box beam has a wall thickness of t = 0.375 in.,
and the pin at A has a diameter of 0.750 in. Determine:
(a) the average shear stress in the pin at A.
(b) the average bearing stress in the box beam at A.

FIGURE P1.29

Solution
Equilibrium: Determine the reaction force exerted on the beam by the pin at A.
M B   Ay a  Pb  P  b  c   0
b  b  c  2b  c
Ay   P  P
a a
2  5.5 ft   3.5 ft
   2, 750 lb 
2.5 ft
 15,950 lb

Average shear stress in the pin at A: The pin diameter is 0.750 in. The cross-sectional area of the pin
is
 
Apin  d2   0.750 in.
 0.4418 in.2
2

4 4
From the support detail figure, we observe that this pin acts in double shear; therefore, the shear area of
the pin is
AV  2 Apin  2  0.4418 in.2   0.8836 in.2
The average shear stress in the pin at A is thus
V Ay 15,950 lb
    18, 051.71 psi  18, 050 psi Ans.
AV AV 0.8836 in.2

Average bearing stress in the box beam at A: The average bearing stress produced in the box beam
by the pin is based on the projected area of the pin. The projected area is equal to the pin diameter
times the wall thickness of the box beam, taking into account that there are two walls that contact the
pin. Therefore, the average bearing stress in the box beam is
Ay 15,950 lb
b    28,355.56 psi  28, 400 psi Ans.
2dt 2  0.750 in. 0.375 in.
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.30 Rigid bar ABC shown in Figure P1.30 is

supported by a pin at bracket A and by tie rod (1).
Tie rod (1) has a diameter of 5 mm, and it is
supported by double-shear pin connections at B and
D. The pin at bracket A is a single-shear
connection. All pins are 7 mm in diameter.
Assume a = 600 mm, b = 300 mm, h = 450 mm, P
= 900 N, and  = 55°. Determine the following:
(a) the normal stress in rod (1)
(b) the average shear stress in pin B
(c) the average shear stress in pin A
FIGURE P1.30

Solution
Equilibrium: Using the FBD shown, calculate
the reaction forces that act on rigid bar ABC.
M A  F1 sin(36.87)(600 mm)
(900 N)sin (55)(900 mm)  0
 F1  1,843.092 N

Fx  Ax  (1,843.092 N)cos(36.87)  (900 N)cos(55)  0

 Ax  958.255 N

Fy  Ay  (1,843.092 N)sin (36.87)  (900 N)sin (55)  0

 Ay  368.618 N
The resultant force at A is
A  (958.255 N)2  (368.618 N)2  1,026.709 N

(a) Normal stress in rod (1).


Arod  (5 mm) 2  19.635 mm 2
4
1,843.092 N
 rod   93.9 MPa Ans.
19.635 mm 2

(b) Shear stress in pin B. The cross-sectional area of a 7 mm diameter pin is:

Apin  (7 mm)2  38.485 mm2
4
Pin B is a double shear connection; therefore, its average shear stress is
1,843.092 N
 pin B   23.9 MPa Ans.
2(38.485 mm2 )

(c) Shear stress in pin A.

Pin A is a single shear connection; therefore, its average shear stress is
1,026.709 N
 pin A   26.7 MPa Ans.
38.485 mm2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.31 The bell crank shown in Figure P1.31 is in

equilibrium for the forces acting in rods (1) and (2).
The bell crank is supported by a 10 mm diameter
pin at B that acts in single shear. The thickness of
the bell crank is 5 mm. Assume a = 65 mm, b =
150 mm, F1 = 1,100 N, and  = 50°. Determine the
following:
(a) the average shear stress in pin B
(b) the average bearing stress in the bell crank at B

FIGURE P1.31

Solution
Equilibrium: Using the FBD shown, calculate the
reaction forces that act on the bell crank.
M B  (1,100 N)sin(50)(65 mm)
 F2 (150 mm)  0
 F2  365.148 N

Fx  Bx  (1,100 N)cos(50)

365.148 N  0
 Bx  341.919 N

Fy  By  (1,100 N)sin(50)  0

 By  842.649 N

The resultant force at B is

B  (341.919 N)2  ( 842.649 N)2  909.376 N

(a) Shear stress in pin B. The cross-sectional area of the 10 mm diameter pin is:

Apin  (10 mm)2  78.540 mm 2
4
Pin B is a single shear connection; therefore, its average shear stress is
909.376 N
 pin B   11.58 MPa Ans.
78.540 mm2

(b) Bearing stress in the bell crank at B. The average bearing stress produced in the bell crank by the
pin is based on the projected area of the pin. The projected area is equal to the pin diameter times the
bell crank thickness. Therefore, the average bearing stress in the bell crank is
909.376 N
b   18.19 MPa Ans.
(10 mm)(5 mm)
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

P1.32 The beam shown in Figure P1.32 is

supported by a pin at C and by a short link
AB. If w = 30 kN/m, determine the average
shear stress in the pins at A and C. Each
pin has a diameter of 25 mm. Assume L =
1.8 m and  = 35°.

FIGURE P1.32

Solution
Equilibrium: Using the FBD shown,
calculate the reaction forces that act on the
beam.

 1.8 m 
M C   F1 sin(35)(1.8 m)  (30 kN/m)(1.8 m)  0
 2 
 F1  47.0731 kN

Fx  Cx  (47.0731 kN)cos(35)  0

 Cx  38.5600 kN

 1.8 m 
M B  C y (1.8 m)  (30 kN/m)(1.8 m)  0
 2 
 C y  27.0000 kN
The resultant force at C is
C  (38.5600 kN)2  (27.0000 kN)2  47.0731 kN

Shear stress in pin A. The cross-sectional area of a 25 mm diameter pin is:


Apin  (25 mm) 2  490.8739 mm 2
4
Pin A is a single shear connection; therefore, its average shear stress is
47,073.1 N
 pin A   95.9 MPa Ans.
490.8739 mm2

Shear stress in pin C.

Pin C is a double shear connection; therefore, its average shear stress is
47,073.1 N
 pin C   47.9 MPa Ans.
2(490.8739 mm2 )
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.33 The bell-crank mechanism shown in

Figure P1.33 is in equilibrium for an
applied load of P = 7 kN applied at A.
Assume a = 200 mm, b = 150 mm, and  =
65°. Determine the minimum diameter d
required for pin B for each of the following
conditions:
(a) The average shear stress in the pin may
not exceed 40 MPa.
(b) The bearing stress in the bell crank
may not exceed 100 MPa.
(c) The bearing stress in the support
bracket may not exceed 165 MPa.
FIGURE P1.33

Solution
Equilibrium: Using the FBD shown, calculate
the reaction forces that act on the bell crank.
M B  (7,000 N)sin(65)(200 mm)
 F1 (150 mm)  0
 F1  8,458.873 N

Fx  Bx  (7,000 N)cos(65)

8,458.873 N  0
 Bx  11,417.201 N

Fy  By  (7,000 N)sin(65)  0

 By  6,344.155 N

The resultant force at B is

B  (11,417.201 N)2  (6,344.155 N)2  13,061.423 N

(a) The average shear stress in the pin may not exceed 40 MPa. The shear area required for the pin
at B is
13,061.423 N
AV  2
 326.536 mm2
40 N/mm
Since the pin at B is supported in a double shear connection, the required cross-sectional area for the pin
is
A
Apin  V  163.268 mm2
2
and therefore, the pin must have a diameter of
4
d (163.268 mm2 )  14.42 mm Ans.

https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

(b) The bearing stress in the bell crank may not exceed 100 MPa. The projected area of pin B on the
bell crank must equal or exceed
13,061.423 N
Ab  2
 130.614 mm2
100 N/mm
The bell crank thickness is 8 mm; therefore, the projected area of the pin is Ab = (8 mm)d. Calculate the
required pin diameter d:
130.614 mm2
d  16.33 mm Ans.
8 mm

(c) The bearing stress in the support bracket may not exceed 165 MPa. The pin at B bears on two 6 mm
thick support brackets. Thus, the minimum pin diameter required to satisfy the bearing stress limit on
the support bracket is
13,061.423 N
Ab  2
 79.160 mm2
165 N/mm

79.160 mm2
d  6.60 mm Ans.
2(6 mm)
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

P1.34 A structural steel bar with a 4.0 in. × 0.875 in. rectangular cross section is subjected to an axial
load of 45 kips. Determine the maximum normal and shear stresses in the bar.

Solution
The maximum normal stress in the steel bar is
F 45 kips
 max    12.86 ksi Ans.
A  4.0 in. 0.875 in.
The maximum shear stress is one-half of the maximum normal stress
 max
 max   6.43 ksi Ans.
2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.35 A stainless steel rod of circular cross section will be used to carry an axial load of 30 kN. The
maximum stresses in the rod must be limited to 100 MPa in tension and 60 MPa in shear. Determine
the required minimum diameter for the rod.

Solution
Based on the allowable 100 MPa tension stress limit, the minimum cross-sectional area of the rod must
equal or exceed
Amin 
F

 30 kN 1, 000 N/kN   300 mm2
 max 100 N/mm2
For the 60 MPa shear stress limit, the minimum cross-sectional area of the rod must be equal or exceed
Amin 
F

 30 kN 1, 000 N/kN   250 mm2
2 max 2  60 N/mm2 
Therefore, the rod must have a cross-sectional area of at least 300 mm2 to satisfy both the normal and
shear stress limits.

The minimum rod diameter D is therefore

 2
dmin  300 mm2  dmin  19.54 mm Ans.
4
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.36 Two wooden members, each having a

width of b = 1.50 in. and a depth of d = 0.5
in., are joined by the simple glued scarf joint
shown in Figure P1.36/37. Assume  = 40°.
If the allowable shear stress for the glue
used in the joint is 90 psi, what is the largest
axial load P that may be applied?
FIGURE P1.36

Solution
The angle  shown for the scarf joint is 40°. The normal
force N perpendicular to the scarf joint can be expressed
as
N  P sin 

and the shear force V parallel to the scarf joint can be

expressed as
V  P cos 

The cross-sectional area of the bar is

A  bd
but the area along the inclined scarf joint is
 d  A
An   b 
 sin   sin 
Consequently, the shear stress nt parallel to the scarf joint can be expressed as
V P cos  P
 nt    sin  cos 
An A / sin  A
Given that the shear stress nt must be limited to 90 psi, solve for the maximum load P as:
P
 nt  sin  cos 
A
P
90 psi  sin 40 cos 40
bd

P
 90 psi 1.50 in. 0.5 in.  137.083 lb  137.1 lb Ans.
sin 40 cos 40

https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

P1.37 Two wooden members, each having a width of

b = 4.50 in. and a depth of d = 1.75 in., are joined by
the simple glued scarf joint shown in Figure P1.36/37.
Assume  = 35°. Given that the compressive axial
load is P = 900 lb, what are the normal stress and shear
stress magnitudes in the glued joint?
FIGURE P1.37

Solution
The angle  shown for the scarf joint is 35°. The normal
force N perpendicular to the scarf joint can be expressed
as
N  P sin 

and the shear force V parallel to the scarf joint can be

expressed as
V  P cos 

The cross-sectional area of the bar is

A  bd
but the area along the inclined scarf joint is
 d  A
An   b 
 sin   sin 

Consequently, the normal stress n magnitude perpendicular to the inclined scarf joint can be expressed
as
N P sin  P
n    sin 2 
An A / sin  A
900 lb
 sin 2 35  37.6 psi Ans.
 4.50 in.1.75 in.

and the shear stress nt magnitude parallel to the scarf joint can be expressed as
V P cos  P
 nt    sin  cos 
An A / sin  A
900 lb
 sin 35 cos 35  53.7 psi Ans.
 4.50 in.1.75 in.
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

P1.38 Two aluminum plates, each having a width of b = 7.0 in. and a thickness of t = 0.625 in., are
welded together as shown in Figure P1.38/39. Assume a = 4.0 in. For a load of P = 115 kips,
determine (a) the normal stress that acts perpendicular to the weld and (b) the shear stress that acts
parallel to the weld.

FIGURE P1.38/39

Solution
Begin by calculating the angle  for the
weld joint.
a 4.0 in.
tan     0.5714
b 7.0 in.
  29.745

The normal force N perpendicular to the

weld joint can be expressed as
N  P cos

and the shear force V parallel to the weld

joint can be expressed as
V  P sin 

The cross-sectional area of the bar is

A  bt
but the area along the inclined weld joint is
 b  A
An   t 
 cos   cos 

(a) Normal stress perpendicular to the weld: The normal stress n magnitude perpendicular to the
inclined weld joint can be expressed as
N P cos  P
n    cos 2 
An A / cos  A
115 kips
 cos 2 29.745  19.82 ksi Ans.
 7.0 in. 0.625 in.
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

(b) Shear stress parallel to the weld: The shear stress nt magnitude parallel to the weld joint can be
expressed as
V P sin  P
 nt    sin  cos 
An A / cos  A
115 kips
 sin 29.745 cos 29.745  11.32 ksi Ans.
 7.0 in. 0.625 in.
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.39 Two aluminum plates, each having a width of b = 5.0 in. and a thickness of t = 0.75 in., are
welded together as shown in Figure P1.38/39. Assume a = 2.0 in. Specifications require that the
normal and shear stress magnitudes acting in the weld material may not exceed 35 ksi and 24 ksi,
respectively. Determine the largest axial load P that can be applied to the aluminum plates.

FIGURE P1.38/39

Solution
Begin by calculating the angle  for the
weld joint.
a 2.0 in.
tan     0.4
b 5.0 in.
  21.801

The normal force N perpendicular to the

weld joint can be expressed as
N  P cos

and the shear force V parallel to the weld

joint can be expressed as
V  P sin 

The cross-sectional area of the bar is

A  bt
but the area along the inclined weld joint is
 b  A
An   t 
 cos   cos 

Normal stress perpendicular to the weld: The normal stress n magnitude perpendicular to the
inclined weld joint can be expressed as
N P cos  P
n    cos 2 
An A / cos  A
The normal stress perpendicular to the weld joint may not exceed 35 ksi. The allowable load P that
satisfies this constraint is
 A  35 ksi  5.0 in. 0.75 in.
P  n2   152.25 kips
cos  cos2  21.801 
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

Shear stress parallel to the weld: The shear stress nt magnitude parallel to the weld joint can be
expressed as
V P sin  P
 nt    sin  cos 
An A / cos  A
The shear stress parallel to the weld joint may not exceed 24 ksi. The allowable load P that satisfies this
requirement is
P
 nt A

 24 ksi  5.0 in. 0.75 in.  261.00 kips
sin  cos  sin  21.801  cos  21.801 

Allowable load P: The largest axial load P that can be applied to the aluminum plates is thus
P  152.3 kips Ans.
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
th
Mechanics of Materials: An Integrated Learning System, 4 Ed. Timothy A. Philpot

P1.40 Two wooden member are glued

together as shown in Figure P1.40. Each
member has a width of b = 1.50 in. and a
depth of d = 3.50 in. Use  = 75°.
Determine the average shear stress
magnitude in the glue joint if P = 1,300 lb.
FIGURE P1.40

Solution
Using the notion of symmetry, we will consider an FBD
for only the upper half of the left-hand wood piece. The
central angle  for the joint is 75°.

The shear force V parallel to the upper half joint can be

expressed as
P 
V  cos
2 2

The cross-sectional area of the upper half member is

d 
A  b 
2
but the area along the inclined upper half joint is
bd
An 

2sin
2

Consequently, the shear stress nt magnitude parallel to the joint can be calculated as
P 
cos
 nt 
V
 2 2  P sin  cos 
An bd bd 2 2

2sin
2
1,300 lb 75 75
 sin cos  119.6 psi Ans.
1.50 in. 3.50 in. 2 2
https://ebookyab.com/solution-manual-mechanics-of-materials-philpot/
Mechanics of Materials: An Integrated Learning System, 4th Ed. Timothy A. Philpot

P1.41 Two bars are connected with a welded

butt joint as shown in Figure P1.41. The bar
dimensions are b = 200 mm and t = 50 mm,
and the angle of the weld is  = 35°. The
bars transmit a force of P = 250 kN. What
is the magnitude of the average shear stress
that acts on plane AB?
FIGURE P1.41

Solution
The angle  shown for the weld joint is 35°.

The normal force N perpendicular to the weld joint can be

expressed as
N  P sin 

and the shear force V parallel to the weld joint can be

expressed as
V  P cos 

The cross-sectional area of the bar is

A  bt
but the area along the inclined weld joint is
 t  A
An   b 
 sin   sin 

Shear stress parallel to the weld: The shear stress nt magnitude parallel to the weld joint can be
expressed as
V P cos  P
 nt    sin a cos 
An A / sin  A


 250 kN 1, 000 N/kN  sin 35 cos 35  11.75 MPa Ans.
 200 mm  50 mm 