1

DESIGN CONSIDERATIONS FOR WATER-BOTTLE ROCKETS

Read the following information. It is provided to help in the design of your water-bottle rocket and will
help you answer questions in your Water-Bottle Rocket Project packet.

(information from: http://mdavenport.net/Physical%20Science/Rockets/Rocket%20Design%20Info.pdf)

Bottle rockets are excellent devices for investigating Newton's Three Laws of Motion:
1st Law - A rocket will remain on the launch pad until an unbalanced force is exerted, propelling the
rocket upward.
2nd Law - The amount of force depends upon how much air is pumped inside the rocket. You can
increase the force further by adding a small amount of water, which increases the mass expelled by the air
pressure in the rocket.
3rd Law - Finally, the action force of the air (and water) as it rushes out of the nozzle creates an equal
and opposite reaction force propelling the rocket upward.

As with a balloon, air pressurizes the bottle rocket. Adding a small amount of water to the bottle increases
the action force. The water expels from the bottle before the air does.

Newton’s First Law: Objects at rest will stay at rest, or objects in motion will stay in motion unless
acted upon by an unbalanced force.
When the rocket is sitting on the launcher, the forces are balanced because the surface of the
launcher pushes the rocket up while gravity pulls it down. When we pressurize the fluid inside the rocket
and release the locking clamps the forces become unbalanced. A small opening in the bottom of the
rocket will allow fluid to escape in one direction and in doing so provides thrust (force) in the opposite
direction allowing the rocket to propel skyward. This force continues until the pressure forces the last
of the fluid to leave the rocket.

Newton’s Second Law: The acceleration of an object is directly related to the force exerted on the
object and oppositely related to the mass of that object. (A = F/m)
For example: If you use the same amount of force, you can throw a baseball faster that a basketball
because the baseball has less mass.
To get your water bottle rockets to fly to great heights you will need to:
o Minimize the rocket’s mass (weight) while maximizing the amount of force.
o Be careful when minimizing the rocket’s weight. If the rocket is too light it will lose stability as soon
as the water is expelled and turn end over end.
o The greater the mass of the fluid expelled from the rocket, and the faster the fluid can be expelled
from the rocket, the greater the thrust (force) of the rocket.
o Increasing the pressure inside the bottle rocket produces greater thrust. This is because a greater mass
of air inside the bottle escapes with a higher acceleration.
 2
Newton’s Third Law: For every action there is always an opposite and equal reaction.
Like a balloon full of air, the bottle rocket is pressurized. When the locking clamp is released,
fluid escapes the bottle providing an action force that is accompanied by an equal and opposite reaction
force which results in the movement of the rocket in the opposite direction.

o Essentially, the faster the fluid is ejected, and the more mass that is ejected, the greater the reaction
force on the rocket.
Stability - Center of Mass and Center of Pressure:
When a 2-liter bottle is launched, it quickly loses stability and tumbles end over end as soon as the
water is expelled. In order for your rocket to reach heights of 200-300 feet, the rocket must be
aerodynamically stable during flight. To increase the stability of the rocket there are two principles you
need to understand: Center of Mass (CM), and Center of Pressure (CP).
Determining the Center of Mass (CM)
The CM of the rocket is easy to find: it is the point at which the rocket balances. If you were to tie
a string around the rocket at its CM, it would balance from the string horizontally.
Determining the Center of Pressure
The CP is more difficult to determine. The CP exists only when air is flowing past the moving
rocket. The CP is defined as the point along the rocket where, if you were to attach a pivot and then hold
the rocket crossways into the wind by that pivot, the wind forces on either side of the CP are equal.
This principle is similar to that of a weather vane. When wind blows on a weathervane the arrow
points into the wind because the tail of the weathervane has a surface area much greater than the
arrowhead. The flowing air imparts a greater pressure on the tail and therefore the tail is pushed away.
On a rocket the purpose of the fins is to add surface area to the rear of the rocket, which helps keep
the nose of the rocket pointed into the wind. If the fins on a rocket were placed at the front of the rocket,
the nose of the rocket would swap positions with the tail a few feet into the flight, which would be
disastrous!
 3

One method of approximating the CP of a rocket is to make a cardboard cutout shaped like the
silhouette of the rocket, and then find the cutout's balance point. This balance point provides an
approximation of the CP of the rocket.
Relationship of CM to CP
In order for a rocket to fly in a stable fashion the center of mass (CM) of the rocket must be forward of the
center of pressure (CP) (See the figure below).

It is important that the CP is located toward the tail of the rocket and the CM is located toward the nose.
In order to achieve this, the following is recommended:
o Adding fins to a rocket increases the surface area of the tail section. The wind forces will thus
increase in the tail section, which in turn will move the CP toward the fins. In fact, that is the
main function of fins. The larger the fins, the further back the CP will be.
o Adding weight to the nose cone section will help move the CM toward the nose of the rocket.
Experiment with your rocket by adding amounts of modeling clay to the nosecone section of
the rocket and then launching it to check stability and height. Be careful not to add too much
weight as this will slow down the rocket.
o Typically, the longer the rocket, the more stable the rocket’s flight will be. However, the longer
the rocket, the heavier the rocket will be. This means that you need to increase the thrust to
compensate for the extra weight.
o Essentially, you need to minimize the rockets weight without compromising stability.

Size of Nozzle:
Remember that the thrust of the rocket will end when the last of the fluid leaves the nozzle of the
bottle. You can make the nozzle smaller by closing it off with a rubber stopper or similar device.
Arguments for the size of nozzle are given below:
o A wide-open nozzle allows for a lot of thrust but for a very short
period of time.
o Reduced nozzles don't give as much thrust but they burn longer.
Because of this low thrust (i.e., slow launch speeds) you need to have
a rocket that is stable at slower speeds.
o Launches with a reduced nozzle are slower, have a less explosive
launch, are safer in the event of a tip over, and look cool.
o A wide-open nozzle keeps launches fast and stable
 4
Fill Ratio of Water in Rocket
When water is added to the rockets, the effect of mass is demonstrated. Before air can leave the
water rocket, the water has to first be expelled. Because water has a much greater mass than air, it
contributes to a much greater thrust (Newton’s 2nd Law). A rocket filled with water will fly much
farther than a rocket filled only with air. By varying the amount of water and air in the rocket and
graphing how high the rockets travel, you can see that the thrust of the rocket is dependent on the mass
being expelled and the speed of expulsion.
The best way to determine the fill ratio is to launch 3-4 test flights using differing amounts of fluid
and graph the height of rocket flight for each.

Pressure of Fluid:
By using the bicycle pump to pressurize the air inside the rocket, we can increase the launch
pressure of the fluid in the rocket, which will then increase the thrust available to the rocket for lift off.
The rocket launchers you will use for this activity have been regulated to a maximum launch pressure of
100 psi. Typically, you will want to use a pressure close to 100 psi. However, you need to remember
that at high pressures there may be a tradeoff in rocket stability and rocket design considerations related to
center of mass and center of pressure might need to be adjusted.

Air Drag:
As a rocket moves through the air, friction between the rocket surface and the air (air drag) will
slow it down. At the high velocities these rockets achieve, air drag becomes a very significant force. To
reduce air drag, the rocket should be designed so that air passing over the surfaces of the rocket flows in
smooth lines (streamlining) thus reducing drag to a minimum.
Below are examples of nose cone designs for the rocket and their relationship to Air Drag.
 5
Some general rules of design to decrease air drag include:
o The fins should be thin and tapered.
o Swept back fins create less drag than straight fins and rounded corners on a fin create less drag
than sharp corners
Every surface on the rocket should be as smooth as possible.
o The nose cone should be a reasonable shape (see the nose cone designs).

Fins:
Without fins, your rocket will not fly straight. Typically, water bottle rockets have three or four fins
attached at the neck of the bottle. Remember the larger the fins and the further back they are placed
on the rocket, the further back the center of pressure (CP) will be thus increasing the stability of
rocket flight.
There are many fin variations possible. You will need some fine-tuning to get the design right.
Below are some fin design possibilities: use these or come up with your own design.

*** Spiral flight helps stabilize the rocket the same way a football is stabilized by spinning in flight.
However, this spinning motion does tend to use up some of the energy needed for forward motion. To
make a rocket spin, angle the fins slightly when attaching the fins to the rocket or bend the tips of the fins
in a pinwheel fashion.
 6
Nose Cone:
The nose cone serves several purposes for the water bottle rocket. These include:
o The nose cone helps reduce air drag by streamlining the air as it flows past the surface of the
rocket.
o Adding weight to the nose cone helps move the center of mass (CM) toward the nose of the rocket
increasing the stability of the rocket.
o The nose cone is often used to hold a payload such as a parachute.
How to construct a paper nosecone:

Designs to consider to help keep your rocket from being destroyed:

o When making the rocket, the section of the rocket, which is to be pressurized, should not be cut in
any manner or the rocket will not hold pressure.

Bounce Method - Add a Nerf ball, tennis ball, or other device to the nose of the rocket so that it bounces
upon impact.

Parachute method - A parachute can be added to the nosecone of the rocket. The tricky part is getting
the parachute to release on the way down rather than the way up. One method is to add a paper towel
tube to the rocket, place a parachute inside the tube, and then attach the parachute to a tennis ball and then
place the ball on the top of the tube. When the rocket reaches the end of it’s flight and turns to tumble to
earth the ball falls off and deploys the parachute.
 7
Basic Suggested Steps & Ideas

1. Remove the label from the outside of the bottle.

2. Decide how many fins you would like. 4 fins are easier than 3, but, if done correctly, either
way works well. The fin shape is also up to you. See the diagram for the easiest fin shape.
3. Now, it is time to mount the fins onto the rocket. Take a piece of paper and wrap it around the
lower portion of the bottle (near the opening end). Mark the circumference of the bottle where
the piece of paper overlaps its self. Remove the paper and measure the distance to the mark
that was just made. This will tell you the circumference of the bottle. If you are planning 4 fins,
divide the circumference by 4. Use this number to divide the piece of paper into 4 equal
sections and mark the sections. If you are planning for 3 fins, use the same process, but, this
time, divide the piece of paper into 3 sections. Wrap the piece of paper around the bottle as
before and secure it with a piece of tape. Take a felt marker and transfer the section marks on
the paper to the bottle. These marks designate where the fins are to be placed. Make sure
everything is perfectly even, or the rocket will not fly well.
4. Next, take a straight edge (ruler) and draw a line through the mark that was made so you will
have a guideline for fin mounting. Apply a rubber-based cement to the fins, carefully aligning
the fins with the straight lines you have just drawn. Press the fins down onto the bottle and
use a piece of tape on either side of the fins in order to keep them straight while the glue sets.
It is best if only one fin is done at a time and the fin is kept vertical until the glue has set.
Make sure all of the fins are perfectly straight.
5. The final step is to cut the manila folder (or whatever material you choose) into a cone so that
it will fit over the top of the bottle rocket. This will be the nose cone. Cement the nose cone to
the top of the rocket. If you wish, a parachute can be added.
The rocket is now finished. Make sure all glues have dried completely and the fins a securely
attached to the rocket before it is flown.
 8
The following are some suggestions if you would like to use two 2 L bottles and create a parachute:
(information from: http://www.lnhs.org/hayhurst/rockets/)

1. Cut the top and the bottom off of one 2. Tape the cylinder to another bottle to
bottle, so that the center portion or a create a fuselage (a place to store the
cylinder remains. parachute).

3. Get the manila folder; fins will be made from it. Cut 3 shapes out of the folded bottom in the
shape that the diagram shows. Your fins will be triangular.
 9
The next drawing indicates how the fin should look once folded.

4. Mark straight lines on the bottle by putting the bottle in the doorframe or a right angle and
trace a line on the bottle with a marker. Use these lines as guides to place the fins on the
bottles.

5. Make 3 fins and tape them on the rocket. Be sure that the fins are spaced equally around the
rocket body. This can be achieved by using a piece of string, wrapping it around the bottle,
and marking the string where it meets the end. Mark the string and lay it flat on a meter-stick
or ruler. Find the circumference of the bottle by measuring the length of the string to the mark.
Once you know the circumference, then you can divide it by three to find the distances the
fins should be separated.
 10
6. Use the athletic cone to make your nose cone. Use fairly rigid scissors and cut the bottom
square off of the cone. Depending upon your project's mass limitations, place a golf ball sized
piece of clay in the tip of the cone. This will add mass to the cone and give the rocket/cone
more inertia. Then, using scissors, trim the cone to make it symmetrical. (Hint: the diameter of
the bottom of the cone should be a little wider than the diameter of a 2-liter bottle.

7. Attach the cone with string to the top of the other two-
liter bottles so that it looks like the diagram. Tie a knot
in the end of each piece of string to give it more friction
and tape it using a piece of duct tape to the inside of
the cone and to the inside of the rocket body.

8. Many students have trouble with their nosecone getting stuck on the
top of the rocket and not coming off. Making a pedestal for the cone
to sit on can prevent this. It should be high enough up so that there is
space between the cone and the top of the parachute compartment.
You can make a pedestal out of the same material you will make the
fins, the manila folder. Make three mini-fins, invert them and tape
them on the rocket where the cone should sit.

9. Making the Parachute

*Don't forget a good parachute has shroud lines that are at least as long as the diameter of
the canopy.
1. Lay your garbage bag out flat. Cut off
the closed end. It should look like a
large rectangle and be open at both
ends. Lay down the bag on a flat
surface and smooth it out.

2. The bag has a long side and

a short side and is open at
both ends. Fold it in two so
that the short side is half as
long as it was originally.
 11
4. Make a triangle with the base of the triangle being the closed end of the previous fold.

5. Now fold it again. Fold the hypotenuse so that it lines up with the right side of the triangle
in the above drawing.

6. Examine the base of the triangle and find the

shortest length from the tip to the base. This is the
limiting factor for chute size. The most pointed end
will end up being the middle of the canopy.
For an example; if you want the diameter of the
chute to be 34 inches then measure 17 inches
from the center of the canopy (the most pointed
side of the parachute) along each side, mark it and
then cut it.
 12
7. After cutting it, unfold it. If you have been successful
there should be two canopies.
8. Fold the canopy in half, then into quarters, then into
eighths. Carefully crease the folds each time.
Crease it well and fold it again. Now the canopy is
divided into 16ths. Unfold the parachute. Notice the
crease marks. Get masking tape and put a piece
around the edge at each fold mark. You may also
use Avery reinforcement tabs. Place one on both the
inside and outside of every crease, making sure that
they are overlaid on top of each other.
9. Punch holes through every piece of masking tape or
Avery tab pairs and use these to attach the kite-
string shroud lines.
As mentioned earlier, the minimum length of the
shroud line should be the same length as the
diameter of the canopy.
10. After punching the holes, fold the canopy in half.
Pick four holes and tie the shroud lines to the
holes. After doing this tie the four lines together at
the end most distant from the canopy.
Repeat this four times until the chute is completed.
10. Once you have it complete, attach it inside the fuselage. Generally a couple of pieces of duct
tape will hold the parachute to the rocket. Pack the parachute loosely and put the nosecone
on the rocket.
You are now ready to launch your rocket!