Scribd
Upload
165 views

DragonlockUltimate Instr Building4

The document provides instructions for 3D printing terrain models from a DRAGONLOCK terrain system including basic materials, printing settings for different models, and links for additional resources like painting tutorials and printer forums.

Uploaded by

pisof
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
165 views

DragonlockUltimate Instr Building4

The document provides instructions for 3D printing terrain models from a DRAGONLOCK terrain system including basic materials, printing settings for different models, and links for additional resources like painting tutorials and printer forums.

Uploaded by

pisof
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

Getting Started

Welcome to the DRAGONLOCK: Ultimate™ terrain system. This instruction manual will outline some
basic materials you will need for 3D printing these models, specific printing information for the models in
this set, and links to additional resources.

For more information on getting started with 3D printing, help with choosing a printer, settings for many
popular printers, troubleshooting, and more; please visit our 3D Printer forums:
http://fatdragongames.proboards.com/board/21/3d-printing-dragonlock-terrain

For painting tutorials on these and other models in the DRAGONLOCK: Ultimate™ product line, please
visit our Youtube channel:
https://www.youtube.com/channel/UC5Lbnd97HV3rU98gcwHklzQ

Basic Tools and Materials


For gluing models with multiple pieces together, we
have found that Gorilla Glue works great (especial-
ly the ‘gel’ type.)

While not necessary, it helps to have a pair of small


tweezers on hand. You’ll find yourself using them
often to pull odd strands of plastic off the model,
getting small bits of plastic out of the printer, etc.
Absolutely essential is a small metal spatula to help
remove models from your build plate. We’ve found
that ones like this from art supply aisles at craft
stores work great and should only cost you a few
dollars.

When printing PLA on a non-heated build plate, ap-


plying blue painter tape to your build-plate works
great to help the plastic adhere.

To make your print stick as well as possible, you


can wipe off newly applied tape with a paper towel
that has a little rubbing alcohol on it (the tape has
a wax coating on the back that sometimes inhibits
the plastic from properly sticking to it).
General printing tips for DRAGONLOCK: Ultimate™ models
With the wide variety of printers and filaments on the market, it isn’t possible for us to list printer settings
that will work with multiple machines. Please visit the Fat Dragon Games forums for printer-specific tips and
information:

http://fatdragongames.proboards.com/board/21/3d-printing-dragonlock-terrain

Using the DRAGONBITE™ clips

Before inserting a Dragonbite™ clip, you must first remove the printing support present in each slot on all
four sides of every model. We recommend using needle-nose pliers to gently twist the support out of place
(always wear eye protection when using tools.) Clips should be printed with 15-20% infill (but can be printed
with 0%.)

To connect DRAGONLOCK™ Ultimate models together, simply insert a Dragonbite™ clip into the slot of
one model, then slide the adjoining model into the opposite side. In addition to the standard v2.0 clip, there
is an optional looser clip included.
‘Timber and Stone Walls’ Model List

Wall D Door
Wall D 2 window

Wall A Wall C

Wall D 1 window
Wall C 1 window

Gables
Wall D Wall B
Printing info:
Filament:
•We recommend using PLA (we use Hatchbox in the FDG office)

Layer Height:
•All clips, wall models & stairs: 150 micron/.15mm recommended (200 micron/.2mm works great as well)
•Door: 100 micron/.1mm recommended

Top/Bottom layers:
•6 layers or .9mm

Infill:
•0% on all models

Rafts:
•None

Brim:
•None

DRAGONLOCK™, DRAGONLOCK: Ultimate™, and Dragonbite™ are trademarks of Fat Dragon Games. @2017 Fat Dragon Games. All rights reserved.
For more information please visit: www.fatdragongames.com

You might also like