TOPIC 4 - WIND SENSOR

Wind Sensor
INTENDED LEARNING OUTCOME
At the end of the topic, the student must be able to:
 describes the basic principles of wind sensors
 demonstrates ordinary readings of wind speed and direction
Anemometer
Jump to navigationJump to search

https://en.wikipedia.org/wiki/File:Wea00920.jpg

A hemispherical cup anemometer of the type invented in 1846 by John Thomas Romney
Robinson.

An anemometer is a device used for measuring wind

speed and direction. It is also a common weather
station instrument. The term is derived from the Greek
word anemos, which means wind, and is used to describe any
wind speed instrument used in meteorology. The first known
description of an anemometer was given by Leon Battista
Alberti in 1450.
 
History
The anemometer has changed little since its development in the 15th century. Leon
Battista Alberti (1404–1472) is said to have invented the first mechanical anemometer
around 1450. In the ensuing centuries numerous others, including Robert Hooke (1635–
1703), developed their own versions, with some being mistakenly credited as the
inventor. In 1846, John Thomas Romney Robinson (1792–1882) improved upon the
design by using four hemispherical cups and mechanical wheels. In 1926, Canadian
meteorologist John Patterson (January 3, 1872 – February 22, 1956) developed a
three-cup anemometer, which was improved by Brevoort and Joiner in 1935. In
1991, Derek Weston added the ability to measure wind direction. In 1994, Andreas
Pflitsch developed the sonic anemometer.[1]

Velocity anemometers
Cup anemometers

https://en.wikipedia.org/wiki/File:Cup-Anemometer-Animation.gif

Cup anemometer animation

A simple type of anemometer was invented in 1845 by Rev Dr John Thomas Romney
Robinson, of Armagh Observatory. It consisted of four hemispherical cups mounted on
horizontal arms, which were mounted on a vertical shaft. The air flow past the cups in
any horizontal direction turned the shaft at a rate that was roughly proportional to the
wind speed. Therefore, counting the turns of the shaft over a set time interval produced
a value proportional to the average wind speed for a wide range of speeds. It is also
called a rotational anemometer.
On an anemometer with four cups, it is easy to see that since the cups are arranged
symmetrically on the end of the arms, the wind always has the hollow of one cup
presented to it and is blowing on the back of the cup on the opposite end of the cross.
Since a hollow hemisphere has a drag coefficient of .38 on the spherical side and 1.42
on the hollow side,[2] more force is generated on the cup that is presenting its hollow
side to the wind. Because of this asymmetrical force, torque is generated on the axis of
the anemometer, causing it to spin.
Theoretically, the speed of rotation of the anemometer should be proportional to the
wind speed because the force produced on an object is proportional to the speed of the
fluid flowing past it. However, in practice other factors influence the rotational speed,
including turbulence produced by the apparatus, increasing drag in opposition to the
torque that is produced by the cups and support arms, and friction of the mount point.
When Robinson first designed his anemometer, he asserted that the cups moved one-
third of the speed of the wind, unaffected by the cup size or arm length. This was
apparently confirmed by some early independent experiments, but it was incorrect.
Instead, the ratio of the speed of the wind and that of the cups, the anemometer factor,
depends on the dimensions of the cups and arms, and may have a value between two
and a little over three. Every previous experiment involving an anemometer had to be
repeated after the error was discovered.
The three-cup anemometer developed by the Canadian John Patterson in 1926 and
subsequent cup improvements by Brevoort & Joiner of the United States in 1935 led to
a cupwheel design with a nearly linear response and had an error of less than 3% up to
60 mph (97 km/h). Patterson found that each cup produced maximum torque when it
was at 45° to the wind flow. The three-cup anemometer also had a more constant
torque and responded more quickly to gusts than the four-cup anemometer.
The three-cup anemometer was further modified by the Australian Dr. Derek Weston in
1991 to measure both wind direction and wind speed. Weston added a tag to one cup,
which causes the cupwheel speed to increase and decrease as the tag moves
alternately with and against the wind. Wind direction is calculated from these cyclical
changes in cupwheel speed, while wind speed is determined from the average
cupwheel speed.
Three-cup anemometers are currently used as the industry standard for wind resource
assessment studies & practice.

Vane anemometers
One of the other forms of mechanical velocity anemometer is the vane anemometer. It
may be described as a windmill or a propeller anemometer. Unlike the Robinson
anemometer, whose axis of rotation is vertical, the vane anemometer must have its axis
parallel to the direction of the wind and therefore horizontal. Furthermore, since the wind
varies in direction and the axis has to follow its changes, a wind vane or some other
contrivance to fulfill the same purpose must be employed.
A vane anemometer thus combines a propeller and a tail on the same axis to obtain
accurate and precise wind speed and direction measurements from the same
instrument.[3] The speed of the fan is measured by a rev counter and converted to a
windspeed by an electronic chip. Hence, volumetric flow rate may be calculated if the
cross-sectional area is known.
In cases where the direction of the air motion is always the same, as in ventilating
shafts of mines and buildings, wind vanes known as air meters are employed, and give
satisfactory results.[4]
o Vane anemometers
 o

o
Vane style of anemometer
 
o

Helicoid propeller anemometer incorporating a wind vane for

orientation
 
o

o
Vane style of anemometer
 
o

Helicoid propeller anemometer incorporating a wind vane for

orientation
 
o
 Hand-held low-speed vane anemometer

Hand-held digital anemometer or Byram anenometer.

Hot-wire anemometers

https://en.wikipedia.org/wiki/File:Hd_sonde.jpg

Hot-wire sensor
Hot wire anemometers use a fine wire (on the order of several micrometres) electrically
heated to some temperature above the ambient. Air flowing past the wire cools the wire.
As the electrical resistance of most metals is dependent upon the temperature of the
metal (tungsten is a popular choice for hot-wires), a relationship can be obtained
between the resistance of the wire and the speed of the air. [5] In most cases, they cannot
be used to measure the direction of the airflow, unless coupled with a wind vane.
Several ways of implementing this exist, and hot-wire devices can be further classified
as CCA (constant current anemometer), CVA (constant voltage anemometer) and CTA
(constant-temperature anemometer). The voltage output from these anemometers is
thus the result of some sort of circuit within the device trying to maintain the specific
variable (current, voltage or temperature) constant, following Ohm's law.
Additionally, PWM (pulse-width modulation) anemometers are also used, wherein the
velocity is inferred by the time length of a repeating pulse of current that brings the wire
up to a specified resistance and then stops until a threshold "floor" is reached, at which
time the pulse is sent again.
Hot-wire anemometers, while extremely delicate, have extremely high frequency-
response and fine spatial resolution compared to other measurement methods, and as
such are almost universally employed for the detailed study of turbulent flows, or any
flow in which rapid velocity fluctuations are of interest.
An industrial version of the fine-wire anemometer is the thermal flow meter, which
follows the same concept, but uses two pins or strings to monitor the variation in
temperature. The strings contain fine wires, but encasing the wires makes them much
more durable and capable of accurately measuring air, gas, and emissions flow in
pipes, ducts, and stacks. Industrial applications often contain dirt that will damage the
classic hot-wire anemometer.

https://en.wikipedia.org/wiki/File:Laser_anemometer.png

Drawing of a laser anemometer. The laser light is emitted (1) through the front lens (6) of the
anemometer and is backscattered off the air molecules (7). The backscattered radiation (dots)
re-enters the device and is reflected and directed into a detector (12).

Laser Doppler anemometers

In laser Doppler velocimetry, laser Doppler anemometers use a beam of light from
a laser that is divided into two beams, with one propagated out of the anemometer.
Particulates (or deliberately introduced seed material) flowing along with air molecules
near where the beam exits reflect, or backscatter, the light back into a detector, where it
is measured relative to the original laser beam. When the particles are in great motion,
they produce a Doppler shift for measuring wind speed in the laser light, which is used
to calculate the speed of the particles, and therefore the air around the anemometer. [6]
https://en.wikipedia.org/wiki/File:Ultrasonic_Windsensor.png

2D ultrasonic anemometer with 3 paths

Ultrasonic anemometers

https://en.wikipedia.org/wiki/File:WindMaster.jpg

3D ultrasonic anemometer
Ultrasonic anemometers, first developed in the 1950s, use ultrasonic sound waves to
measure wind velocity. They measure wind speed based on the time of flight of sonic
pulses between pairs of transducers. Measurements from pairs of transducers can be
combined to yield a measurement of velocity in 1-, 2-, or 3-dimensional flow. The spatial
resolution is given by the path length between transducers, which is typically 10 to
20 cm. Ultrasonic anemometers can take measurements with very fine temporal
resolution, 20 Hz or better, which makes them well suited for turbulence measurements.
The lack of moving parts makes them appropriate for long-term use in exposed
automated weather stations and weather buoys where the accuracy and reliability of
traditional cup-and-vane anemometers are adversely affected by salty air or dust. Their
main disadvantage is the distortion of the air flow by the structure supporting the
transducers, which requires a correction based upon wind tunnel measurements to
minimize the effect. An international standard for this process, ISO 16622 Meteorology
—Ultrasonic anemometers/thermometers—Acceptance test methods for mean wind
measurements is in general circulation. Another disadvantage is lower accuracy due to
precipitation, where rain drops may vary the speed of sound.
Since the speed of sound varies with temperature, and is virtually stable with pressure
change, ultrasonic anemometers are also used as thermometers.
Two-dimensional (wind speed and wind direction) sonic anemometers are used in
applications such as weather stations, ship navigation, aviation, weather buoys and
wind turbines. Monitoring wind turbines usually requires a refresh rate of wind speed
measurements of 3 Hz,[7] easily achieved by sonic anemometers. Three-dimensional
sonic anemometers are widely used to measure gas emissions and ecosystem fluxes
using the eddy covariance method when used with fast-response infrared gas
analyzers or laser-based analyzers.
Two-dimensional wind sensors are of two types:
 Two ultrasounds paths: These sensors have four arms. The disadvantage of this
type of sensor is that when the wind comes in the direction of an ultrasound path,
the arms disturb the airflow, reducing the accuracy of the resulting measurement.
 Three ultrasounds paths: These sensors have three arms. They give one path
redundancy of the measurement which improves the sensor accuracy and reduces
aerodynamic turbulence.
Acoustic resonance anemometers

https://en.wikipedia.org/wiki/File:Acoustic_Resonance_Wind_Sensor.jpg

Acoustic resonance anemometer

Acoustic resonance anemometers are a more recent variant of sonic anemometer. The
technology was invented by Savvas Kapartis and patented in 1999. [8] Whereas
conventional sonic anemometers rely on time of flight measurement, acoustic
resonance sensors use resonating acoustic (ultrasonic) waves within a small purpose-
built cavity in order to perform their measurement.

https://en.wikipedia.org/wiki/File:Acoustic_Resonance_Anemometer.jpg

Acoustic resonance principle

Built into the cavity is an array of ultrasonic transducers, which are used to create the
separate standing-wave patterns at ultrasonic frequencies. As wind passes through the
cavity, a change in the wave's property occurs (phase shift). By measuring the amount
of phase shift in the received signals by each transducer, and then by mathematically
processing the data, the sensor is able to provide an accurate horizontal measurement
of wind speed and direction.
Because acoustic resonance technology enables measurement within a small cavity,
the sensors tend to be typically smaller in size than other ultrasonic sensors. The small
size of acoustic resonance anemometers makes them physically strong and easy to
heat, and therefore resistant to icing. This combination of features means that they
achieve high levels of data availability and are well suited to wind turbine control and to
other uses that require small robust sensors such as battlefield meteorology. One issue
with this sensor type is measurement accuracy when compared to a calibrated
mechanical sensor. For many end uses, this weakness is compensated for by the
sensor's longevity and the fact that it does not require recalibration once installed.

Ping-pong ball anemometers

A common anemometer for basic use is constructed from a ping-pong ball attached to a
string. When the wind blows horizontally, it presses on and moves the ball; because
ping-pong balls are very lightweight, they move easily in light winds. Measuring the
angle between the string-ball apparatus and the vertical gives an estimate of the wind
speed.
This type of anemometer is mostly used for middle-school level instruction, which most
students make on their own, but a similar device was also flown on the Phoenix Mars
Lander.[9]
Pressure anemometers

https://en.wikipedia.org/wiki/File:Britannia_Yacht_Club_tour,_burgee,_and_wind_gauge.jpg

Britannia Yacht Club clubhouse tour, burgee, and wind gauge on roof

The first designs of anemometers that measure the pressure were divided into plate and
tube classes.

Plate anemometers
These are the first modern anemometers. They consist of a flat plate suspended from
the top so that the wind deflects the plate. In 1450, the Italian art architect Leon Battista
Alberti invented the first mechanical anemometer; in 1664 it was re-invented by Robert
Hooke (who is often mistakenly considered the inventor of the first anemometer). Later
versions of this form consisted of a flat plate, either square or circular, which is kept
normal to the wind by a wind vane. The pressure of the wind on its face is balanced by
a spring. The compression of the spring determines the actual force which the wind is
exerting on the plate, and this is either read off on a suitable gauge, or on a recorder.
Instruments of this kind do not respond to light winds, are inaccurate for high wind
readings, and are slow at responding to variable winds. Plate anemometers have been
used to trigger high wind alarms on bridges.

Tube anemometers

https://en.wikipedia.org/wiki/File:Tube_anemometer_invented_by_William_Henry_Dines.jpg
Tube anemometer invented by William Henry Dines. The movable part (right) is mounted on the
fixed part (left).

https://en.wikipedia.org/wiki/File:Instruments_at_Mount_Washington_Observatory.JPG

Instruments at Mount Washington Observatory. The pitot tube static anemometer is on the right.

https://en.wikipedia.org/wiki/File:Pitot_tube_static_anemometer.JPG

The pointed head is the pitot port. The small holes are connected to the static port.
James Lind's anemometer of 1775 consisted of a glass U tube containing a
liquid manometer (pressure gauge), with one end bent in a horizontal direction to face
the wind and the other vertical end remains parallel to the wind flow. Though the Lind
was not the first it was the most practical and best known anemometer of this type. If
the wind blows into the mouth of a tube it causes an increase of pressure on one side of
the manometer. The wind over the open end of a vertical tube causes little change in
pressure on the other side of the manometer. The resulting elevation difference in the
two legs of the U tube is an indication of the wind speed. However, an accurate
measurement requires that the wind speed be directly into the open end of the tube;
small departures from the true direction of the wind causes large variations in the
reading.
The successful metal pressure tube anemometer of William Henry Dines in 1892
utilized the same pressure difference between the open mouth of a straight tube facing
the wind and a ring of small holes in a vertical tube which is closed at the upper end.
Both are mounted at the same height. The pressure differences on which the action
depends are very small, and special means are required to register them. The recorder
consists of a float in a sealed chamber partially filled with water. The pipe from the
straight tube is connected to the top of the sealed chamber and the pipe from the small
tubes is directed into the bottom inside the float. Since the pressure difference
determines the vertical position of the float this is a measure of the wind speed. [10]
The great advantage of the tube anemometer lies in the fact that the exposed part can
be mounted on a high pole, and requires no oiling or attention for years; and the
registering part can be placed in any convenient position. Two connecting tubes are
required. It might appear at first sight as though one connection would serve, but the
differences in pressure on which these instruments depend are so minute, that the
pressure of the air in the room where the recording part is placed has to be considered.
Thus if the instrument depends on the pressure or suction effect alone, and this
pressure or suction is measured against the air pressure in an ordinary room, in which
the doors and windows are carefully closed and a newspaper is then burnt up the
chimney, an effect may be produced equal to a wind of 10 mi/h (16 km/h); and the
opening of a window in rough weather, or the opening of a door, may entirely alter the
registration.
While the Dines anemometer had an error of only 1% at 10 mph (16 km/h), it did not
respond very well to low winds due to the poor response of the flat plate vane required
to turn the head into the wind. In 1918 an aerodynamic vane with eight times the torque
of the flat plate overcame this problem.
Pitot tube static anemometers
Modern tube anemometers use the same principle as in the Dines anemometer but
using a different design. The implementation uses a pitot-static tube which is a pitot
tube with two ports, pitot and static, that is normally used in measuring the airspeed of
aircraft. The pitot port measures the dynamic pressure of the open mouth of a tube with
pointed head facing wind, and the static port measures the static pressure from small
holes along the side on that tube. The pitot tube is connected to a tail so that it always
makes the tube's head to face the wind. Additionally, the tube is heated to prevent rime
ice formation on the tube.[11] There are two lines from the tube down to the devices to
measure the difference in pressure of the two lines. The measurement devices can
be manometers, pressure transducers, or analog chart recorders.[12]

Effect of density on measurements

In the tube anemometer the dynamic pressure is actually being measured, although the
scale is usually graduated as a velocity scale. If the actual air density differs from the
calibration value, due to differing temperature, elevation or barometric pressure, a
correction is required to obtain the actual wind speed. Approximately 1.5% (1.6% above
6,000 feet) should be added to the velocity recorded by a tube anemometer for each
1000 ft (5% for each kilometer) above sea-level.

Effect of icing
At airports, it is essential to have accurate wind data under all conditions, including
freezing precipitation. Anemometry is also required in monitoring and controlling the
operation of wind turbines, which in cold environments are prone to in-cloud icing. Icing
alters the aerodynamics of an anemometer and may entirely block it from operating.
Therefore, anemometers used in these applications must be internally heated. [13] Both
cup anemometers and sonic anemometers are presently available with heated versions.

Instrument location
In order for wind speeds to be comparable from location to location, the effect of the
terrain needs to be considered, especially in regard to height. Other considerations are
the presence of trees, and both natural canyons and artificial canyons (urban buildings).
The standard anemometer height in open rural terrain is 10 meters.