Scribd
Upload
62 views

Korabor AF744

Korabor A/F744 is a chlorinated rubber-based antifouling paint containing cuprous oxide. It provides effective protection against fouling with an extended docking interval. It has a flat red-brown or dark brown finish and dries fully in 8 hours at 30°C. It can be applied by spray, roller, or brush at 125 microns wet thickness in 2-3 coats.

Uploaded by

Isabelo Abao
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
62 views

Korabor AF744

Korabor A/F744 is a chlorinated rubber-based antifouling paint containing cuprous oxide. It provides effective protection against fouling with an extended docking interval. It has a flat red-brown or dark brown finish and dries fully in 8 hours at 30°C. It can be applied by spray, roller, or brush at 125 microns wet thickness in 2-3 coats.

Uploaded by

Isabelo Abao
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Korabor

A/F744

Product A chlorinated rubber based antifouling paint containing cuprous oxide providing very effective and
Description extended protection against fouling.
Approved as TBT-free antifouling paint by Korean Register of Shipping (KR), Russian Maritime of
Shipping(RMRS)
Recommended Use General purpose antifouling paint, keel to load line, on vessels in global trade, with extended docking
interval.

Physical Properties

Finish and Color Flat. Red Brown, Dark Brown

Drying Time Substrate temperature 5 ℃/41 ℉ 20 ℃/68 ℉ 30 ℃/86 ℉


Set to touch 8h 2h 2h
Dry through 24 h 12 h 8h
* The actual drying time is subject to the film thickness, ventilation, humidity etc., and drying time under other temperature
conditions should be checked and informed by KCC.

Solids by Volume Approx. 50 % (Determined by ISO 3233)

Theoretical 4 ㎡/L in 125 ㎛ dry film thickness on a smooth surface.


Spreading Rate
Specific Gravity Approx. 1.70

Flash Point 26 ℃/79 ℉(Closed cup)

Application Details

Surface Remove any oil, grease, dirt and any other contaminants from the surface before painting by proper
Preparation method such as solvent cleaning and fresh water washing, etc.

Application The surface should be cleaned and dried completely. Do not apply when relative humidity is above
Conditions 85 %. The surface temperature should be at least 2.7 ℃ (5 ℉) above dew point to prevent
condensation. In confined areas, ventilate with clean air during application to assist solvent
evaporation.
Preceding Coat Korabor Aluminium H.B. RH248, Kovinyl Sealer VH137AL, Korepox H.B. EH2560 or according to
specification.
* Tar bleeding may occur from Korepotar H.B. EH173(S),etc.
This effect is only cosmetic problem and has no negative influence on the antifouling performance.
*Renewal : High pressure fresh water hosing to remove salt deposits and other contaminants.
Allow surface to dry before recoating with Korabor A/F744.

Thinning Thinner No. 002

Disclaimer : The information in this data sheet is believed to the best of our knowledge based on laboratory test and practical experience.
However, there are many factors affecting the performance of product and the product quality itself, so we are not able to guarantee
KCC Corporation
without the confirmation of the purpose of using the product from us in writing. We reserve the right to change the data without notice and
you should check that this data sheet is current prior to using the product.
Korabor A/F744

Application Spray (Airless or Air), Roller or Brush application.


Method For airless spray application ;
Nozzle orifice : 635 ㎛ ~ 787 ㎛ (0.025″ ~ 0.031″)
Output pressure : 13.8 MPa ~ 19.7 MPa
Fan : 60 ˚
(Airless spray data are indicative and subject to adjustment)

Typical 125 ㎛ dry.


Film Thickness Two (2) or Three (3) coats are recommended with different color of consecutive coats.
Depending on the purpose and the area of use, different film thickness may be applied..
This will alter spreading rate and may influence drying time and recoating interval.

Recoating Interval At 20 ℃/68 ℉, Minimum : 6 h


Maximum : Free
Before overcoating, remove any oil, salt, chalking material and any other contaminants on aged
coating film completely by proper cleaning method such as solvent cleaning and/or fresh water
washing.

Shelf Life 12 months

Standard Packing 15 L, 18 L
Unit
Remarks Avoid contact with skin and inhalation of paint mist or solvent vapor.
In case of eye contact, the eyes should be rinsed immediately by fresh water continuously for at least
15 minutes. Doctor’s advice is recommended.
In case of skin contact, the exposed area should be cleansed thoroughly with soap and water.
Contaminated clothing should be removed and laundered with soap and water before reuse.
In case of ingestion, swallow promptly a large quantity of milk, egg white or gelatin as a first aid.
(If these are not available, drink a large quantity of water instead.) And obtain immediate medical
attention.

Issued July 2011

Disclaimer : The information in this data sheet is believed to the best of our knowledge based on laboratory test and practical experience.
However, there are many factors affecting the performance of product and the product quality itself, so we are not able to guarantee
KCC Corporation
without the confirmation of the purpose of using the product from us in writing. We reserve the right to change the data without notice and
you should check that this data sheet is current prior to using the product.

You might also like