Scribd
Upload
1K views2 pages

CAT C18 Connecting Rod Bearings - Install

Uploaded by

Sayel Mokhaimer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
1K views2 pages

CAT C18 Connecting Rod Bearings - Install

Uploaded by

Sayel Mokhaimer
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

12/25/2018 C18 Industrial Engine WJB00001-UP(SEBP4502 - 28) - Documentation

Previous Screen
Welcome: q631tm
Product: INDUSTRIAL ENGINE
Model: C18 INDUSTRIAL ENGINE WJB00266
Configuration: C18 Industrial Engine WJB00001-UP

Disassembly and Assembly


C18 Fire Pump Industrial Engine
Media Number -KENR8146-02 Publication Date -01/10/2014 Date Updated -17/10/2014

i02221853

Connecting Rod Bearings - Install


SMCS - 1219-012

Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9082 Engine Turning Tool 1

B 8T-3052 Degree Wheel 1

NOTICE
Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

Note: Install the connecting rod bearings dry when clearance checks are performed. Refer to Disassembly and Assembly, "Bearing
Clearance - Check". Apply clean engine oil on the connecting rod bearings for final assembly.

Illustration 1 g00998730

1. Use Tooling (A) to rotate the crankshaft until the connecting rod journal is at the bottom center.

2. Install a new lower half connecting rod bearing (3) in connecting rod bearing cap (2).

https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/s… 1/2
12/25/2018 C18 Industrial Engine WJB00001-UP(SEBP4502 - 28) - Documentation
Note: Ensure that bearing locking tab (4) is located in the notch of the connecting rod bearing cap.

3. Install a new upper half connecting rod bearing in the connecting rod.

Note: Ensure that the bearing locking tab is located in the notch of the connecting rod.

4. Pull the connecting rod onto the crankshaft.

Illustration 2 g01016640

5. Position connecting rod bearing cap (2) on the connecting rod.

Note: Ensure that the number on the side of the connecting rod bearing cap is on the same side as the number on the connecting rod.
The bearing tabs of the connecting rod bearing cap and the connecting rod are located on the side of the piston cooling jet.

6. Lubricate the threads of bolts (1) with clean engine oil. Install the bolts.

7. Tighten bolts (1), as follows:

a. Tighten Bolt (A) and Bolt (C) to a torque of 70 ± 4 N·m (52 ± 3 lb ft).

b. Tighten Bolt (B) and Bolt (D) to a torque of 70 ± 4 N·m (52 ± 3 lb ft).

c. Turn Bolt (B) and Bolt (D) for an additional 60 ± 5 degrees (1/6 turn).

Note: If Tooling (B) is not used, place an index mark on each bolt.

d. Tighten Bolt (A) and Bolt (C) again to a torque of 70 ± 4 N·m (52 ± 3 lb ft).

e. Tighten Bolt (A) and Bolt (C) for an additional 60 ± 5 degrees (1/6 turn).

Note: If Tooling (B) is not used, place an index mark on each bolt.

f. Rotate the crankshaft in order to ensure that the crankshaft turns freely.

End By:

a. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install".

Copyright 1993 - 2018 Caterpillar Inc. Tue Dec 25 2018 09:53:57 GMT+0400 (Gulf Standard Time)
All Rights Reserved.
q631tm
Private Network For SIS Licensees.

https://sis.cat.com/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisweb/mediasearch/mediaheaderinfoframeset.jsp&calledpage=/s… 2/2

You might also like