Scribd
Upload
58 views2 pages

ORAJET 3165 - Technical Data Sheet (EN)

Uploaded by

Dejan Pekić
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
58 views2 pages

ORAJET 3165 - Technical Data Sheet (EN)

Uploaded by

Dejan Pekić
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Technical

ORAJET® 3165 Datasheet


2020/46
Page 1 of 2

Description
Blended polymeric PVC film, available in white with a glossy or matt surface and in transparent with a glossy or matt surface

Release Paper
Double sided PE coated paper, one side siliconised, 143 g/m²

Adhesive
Solvent polyacrylate, permanent, grey or transparent

Area of use
For brilliant and colourful digital advertising prints in short- and medium-term outdoor applications.

Printing Method
Inkjet printing with solvent based inks, UV- or latex inks

Technical Data
Thickness (1) (without paper and adhesive) 100 micron
(1)
Dimensional stability (FINAT TM 14) Adhered to steel shrinkage, no shrinkage in cross direction, in
length 0,4 mm max.
Temperature resistance (2) Adhered to aluminium, -40° C to +80° C, no variation
Sea water resistance (DIN 50021) Adhered to aluminium, after 100h/23° C, no variation
Fire behavior Adhered to steel, self-extinguishing
(1)
Adhesive power (FINAT TM 1, after 24h, stainless steel) 18 N/25 mm
Tensile strength (1) (DIN EN ISO 527) Along: > 19 MPa
Across: > 19 MPa
Elongation at break (1) (DIN EN ISO 527) Along: > 130%
Across: > 150%
Shelf life (3) 2 years
Application temperature >+8° C
Maximum service life by specialist application 5 years (not printed)
Applies for vertical outdoor exposure (4)

(1) (2) short-time (3) (4)


average exposure in original packaging, at 20° C and 50% relative humidity normal climate of Central Europe

Note
After printing, the ink must be allowed to thoroughly dry, in order to avoid any issues when later combined with the laminate.
Surfaces to which the material will be applied must be thoroughly cleaned and free from dust, grease or any contamination
which could affect the adhesion of the material. Freshly lacquered or painted surfaces should be allowed to dry for at least
three weeks and to completely cure. The compatibility of the selected lacquers and paints should be tested by the user, prior
to the application of the material. Furthermore the application information published by ORAFOL must be considered. The
batch traceability according to ISO 9001 is possible on the basis of the roll number.

ORAFOL Europe GmbH - Orafolstraße 1 – D 16515 Oranienburg - Germany


[email protected] – www.orafol.com
Technical
ORAJET® 3165 Datasheet
2020/46
Page 2 of 2

IMPORTANT NOTICE
All ORAJET® products are subject to careful quality control throughout the manufacturing process and are warranted to be of
merchantable quality and free from manufacturing defects. Published information concerning ORAJET® products is based
upon research which the Company believes to be reliable although such information does not constitute a warranty. Because
of the variety of uses of ORAJET® products and the continuing development of new applications, the purchaser should
carefully consider the suitability and performance of the product for each intended use, and the purchaser shall assume all
risks regarding such use. All specifications are subject to change without prior notice.
ORAJET® is a registered trademark of ORAFOL Europe GmbH.

ORAFOL Europe GmbH - Orafolstraße 1 – D 16515 Oranienburg - Germany


[email protected] – www.orafol.com

You might also like