See discussions, stats, and author profiles for this publication at: https://www.researchgate.

net/publication/331412969

Energy Harvesting on Footsteps Using Piezoelectric based on Circuit LCT3588

and Boost up Converter

Article  in  International Journal of Electrical and Computer Engineering · December 2018

DOI: 10.11591/ijece.v8i6.pp4104-4110

CITATIONS READS

19 3,420

6 authors, including:

Yosi Apriani
Universitas Muhammadiyah Palembang
21 PUBLICATIONS   58 CITATIONS   

SEE PROFILE

Some of the authors of this publication are also working on these related projects:

SOSIALISASI PENGGUNAAN INVERTER BERBASIS SOLAR SEL DI LAYANAN KESEHATAN CUMA-CUMA (LKC) DOMPET DUAFA PALEMBANG SEBAGAI UPAYA PENINGKATAN
KUALITAS LAYANAN KESEHATAN View project

All content following this page was uploaded by Yosi Apriani on 19 February 2020.

The user has requested enhancement of the downloaded file.

International Journal of Electrical and Computer Engineering (IJECE)
Vol. 8, No. 6, December 2018, pp. 4104~4110
ISSN: 2088-8708, DOI: 10.11591/ijece.v8i6.pp4104-4110  4104

Energy Harvesting on Footsteps Using Piezoelectric based on

Circuit LCT3588 and Boost up Converter

Iswanto1, Slamet Suripto 2, Faaris Mujahid3, Karisma Trinanda Putra4, Noor Pratama Apriyanto5,
Yosi Apriani6
1,2,3,4,5Department
of Electrical Engineering, Universitas Muhammadiyah Yogyakarta, Indonesia
6Department of Electrical Engineering, Universitas Muhammadiyah Palembang, Indonesia
1Laboratory Control, Robotics, and Computer Vision, Universitas Muhammadiyah Yogyakarta, Indonesia

Article Info ABSTRACT

Article history: Piezoelectric utilization as a generator is an effort to obtain electrical energy
that refers to the concept of energy harvesting referring the development of
Received Nov 11, 2017 piezoelectric as a generator that converts the pressure or vibration generated
Revised Jul 7, 2018 from steps into electrical energy that can be used on low-power electronic
Accepted Jul 27, 2018 devices. Because the use of piezoelectric as a generator allows the use in
charging low voltage, a larger resource is required in different series. Based
on the problem, an energy harvesting device and a voltage amplifier are
Keyword: created to increase the voltage of the pizoelectric output. An arduino
microcontroller is used to control the energy harvesting device and voltage
Arduino booster. It is required approximately 10 steps to charge four AA 1.2 Volt
Conventional energy batteries and 80 steps to charge two 12 volt batteries respectively.
Microcontroller
Piezoelectric
Renewable energy source Copyright © 2018 Institute of Advanced Engineering and Science.
All rights reserved.

Corresponding Author:
Iswanto,
Laboratory Control, Robotics, and Computer Vision,
Universitas Muhammadiyah Yogyakarta,
Yogyakarta, Indonesia.
Email: [email protected]

1. INTRODUCTION
The current energy crisis is a problem that greatly affects the survival of human life, especially the
problem of electrical energy. The development of technology makes most of human activities are supported
by various equipment and technologies that use electrical energy as a source of energy. This certainly makes
the electrical energy as an inseparable part in all human activities. The main source of power today is fossil
fuel, but fossil fuel is non-renewable natural resource and the availability is limited because it has a certain
amount of mass and if used continuously without any restriction it will considerably decrease and run out.
The production and use of fossil fuel has a detrimental effect on the environment, and fossil fuels are carbon
dioxide producers that produce greenhouse gases. Along with the increasing energy demand and the
unbalanced condition between the demand and supply due to the decrease of the fossil fuel supply, the
development of alternative energy sources is needed to meet current energy needs.
A renewable energy is needed to reduce the use of fossil fuels as a major source of energy for power
generation. It is a source of sustainable energy that is available in nature and can be used in a relatively long
time so that there is no need to worry about the lack of the resources. Reflecting to the last few years, many
studies have been conducted in developing renewable energy sources both in large and small scale. One of
the research developments of renewable energy is energy harvest design. Some previous researchers have
conducted energy harvesting research such as Kymissis et al. conducting a research on energy harvesting on
shoe-use by using micro-generator [1]. When the shoe stepped on, the micro-generator rotates to produce
voltage. Energy harvesting in sea and river using small generators is conducted by Taylor et al. [2].

Journal homepage: http://iaescore.com/journals/index.php/IJECE

Int J Elec & Comp Eng ISSN: 2088-8708  4105

The generator is driven by the flow of river water and ocean currents to produce very low energy. Controls
and modifiers for energy harvesters using micro power are examined by Shengwen Xu et al. [3]. Pizoelectric
transducer is used to generate micro power and digital control is used to increase the dc power of micro
power.
The mechanical analysis of vibrate energy harvesters on pizoelectric is carried out by Blažević
et al. [4]. In an experiment to analyze the mechanics of energy harvesters, a Caterpillar is used to create
vibrations against the pizoelectric. The energy harvester of the pizoelectric transducers is applied to shoes by
Rocha et al. [5]. When the shoes are used for walking, they will produce energy from pizoelectric transducers
applied to the shoes’ pedestal.
Designing a circuit using pizoelectric transducers and capacitors has been conducted by
Pisharody [6]. The circuit is arranged in parallel to which the output voltage is rectified with the diode bridge
circuit. The harvesting of vibrational energy by using pizoelectric transducers has been performed by Wang
et al. [7]. Four pizoelectrics are coupled in parallel to the diode, and then the output voltage is measured and
tested by several forces. The greater the force applied, the greater the voltage resulted.
The dropped energy harvesting using pizoelectric and its model has been conducted by Alkhaddeim
et al. [8]. The pizoelectric circuit is modeled and tested with water droplets such as rain. In the test it is seen
that the voltage generated by the pizoelectric closes to 0.5 volts with a 10Kohm output. Energy harvesting
from low airflow velocity using pizoelectric has been investigated by [9]. Pizoelectric energy harvesters are
installed on the windmill so that when the windmill is rotated, the pizoelectric produces energy. A research
on rectifiers for energy harvesters has been examined by Do et al [10]. The rectifier circuit is examined and
applied to the energy harvester using a Triac component which gate is controlled by a digital block.
The research on inverter design for stand-alone piezoelectric energy harvesting has been conducted
by Stein & Hofmann [11]. The inverters are designed using a new resonant inverter topology that applies
dynamic energy harvesting techniques. The research on super capacitors applied to pizoelectric energy
harvesting has been investigated by Shahriat et al.[12]. This paper presents the application of energy
harvesting on foot steps using pizoelectric transducer. This study is different from the studies previously
mentioned. This research modifies the pizoelectric energy harvesting circuit so that the output voltage from
energy harvesters can be stored at large energy sources such as battery.

2. RESEARCH METHOD
2.1. Hardware Design
This paper presents a renewable energy by using a transducer to convert pressure energy into
electrical energy designed as shown in Figure 1. It shows that the transducer used is piezoelectric which has
the capability as some crystals and other materials in that they can generate electrical voltage if getting
pressure or strain treatments. Piezoelectric has the ability to generate electrical voltage when given a
mechanical pressure. In this study, the pizoelectric is assembled using a parallel circuit as shown in Figure 2.
The picture shows that in one footstep there are 40 pizoelectrics arranged in parallel. The parallel circuit
serves to raise the pizoelectric output current.
The voltage and current generated from the pizoelectric is so small that an energy harvesting circuit
is required. The energy harvesting circuit used is LTC3588 IC circuit. The output voltage generated from this
circuit is very small that is 1 volt so that the output voltage is not able to charge 12 volt energy source. Based
on these problems, this paper explains the idea of how to calibrate a 12-volt battery using energy harvesting
components.
Figure 1 shows that the output from the energy harvester is used to charge two AA batteries. After
the batteries are full, they are connected to the boost step up circuit so that the voltage goes up to 12 volts.
This boost step circuit uses XL6009 IC as shown in Figure 3. It is seen in the picture that the circuit uses
33uH inductor that serves as a current folder. The output of this circuit is used to charge the 12-volt battery.
As shown in Figure 1, the study uses a microcontroller to control the flow of power flowing from the
pizoelectric to the 12 volt battery. The voltage sensor is used to determine the voltage stored in two AA
batteries. This sensor is connected to the Arduino microcontroller and this microcontroller is used to control
the relay. The algorithm to control the relay is fuzzy cell decomposition algorithm [13]. Fuzzy algorithms has
been frequently used by former researchers to control algorithms such as in guadrotor control.

Energy Harvesting on Footsteps Using Piezoelectric Based on Circuit.... (Slamet Suripto)

4106  ISSN: 2088-8708

Figure 1. Design of pizoelectric energy harvester to charge 12 Volt battery

Figure 2. The 40 piezoelectric circuit is coupled by using a parallel circuit

Figure 3. Boost up converter circuit

Int J Elec & Comp Eng, Vol. 8, No. 6, December 2018 : 4104 - 4110
Int J Elec & Comp Eng ISSN: 2088-8708  4107

2.2. Software Design

The function of the microcontroller in the energy harvesting circuit is to do a simple control that is
to control the ignition time on the relay circuit so as to make the channeling of the AA battery voltage to the
12 Volts battery voltage, read the input from the voltage level detector, and give action on each input given
by a voltage level detector circuit,as shown by the flowchart in Figure 4. Figure 4 shows that the initial step
of the program is to initialize the pin and memory usage of the microcontroller that is followed by the ADC
initialization which will be used to read the voltage level [14]-[16].
The program will then read from the signal given by the voltage level detector circuit. When the
voltage is sufficient, the microcontroller will do the ignition control on the relay circuit and turn on the light
indication of the safe input voltage level. When the input voltage indicates the descending level, the
microcontroller stops the control on the relay which is then continued by turning on the LED indicated in red
and the Buzzer sounds. The control algorithm uses fuzzy algorithm control found by zadeh that have been
used in multi-quadrotor path planning [13], closest path planning for motorcycle safety [16], path planning of
robot trash [17] and quadrotor control [18].

Figure 4. Flowchart energy harvesters

3. RESULTS AND ANALYSIS

The system testing and analysis include piezoelectric system test and current reader circuit test
previously made. In piezoelectric system test, forty piezoelectrics were arranged in parallel, then, in the last
stage, there was a test for charging the battery.

3.1. The test on 40 Piezoelectrics in Parallel

The test of the output voltage on the forty piezoelectris in the parallel circuit is shown in Figure 5.
The figure shows that the forty piezoelectris were tested by applying an average weight of people 70 Kg. In
the graph, it can be seen that from fifty tests using heavy pressure of 70 Kg weight of people, the
piezoelectric output voltage varies from 35 Volts to 50 Volts. Although they have the same weight, different
pressures generate different piezoelectric voltages.
The current test of forty piezoelectrics arranged in a parallel circuit is shown in Figure 6. The figure
shows that the forty piezoelectrics are tested by applying an average weight of 70 Kg. From the graph, it can
Energy Harvesting on Footsteps Using Piezoelectric Based on Circuit.... (Slamet Suripto)
4108  ISSN: 2088-8708

be seen that from fifty tests using pressure of people of 70 Kg showed that the piezoelectric output current
varies from 22 milli-ampere to 33 milli-ampere. Although people have the same weight, but different
pressures generate different piezoelectric currents.

Figure 5. Voltages generated by 40 piezoelectrics in parallel

Figure 6. Current generated by 40 piezoelectrics in parallel

3.2. Battery Charging Test

AA battery charging current test using forty piezoelectrics in parallel circuits is shown in Figure 7.
The picture shows that the forty piezoelectrics are tested by gving a pressure of 70 Kg weight. From the
graph, it can be seen that from fifty tests using pressure of people of 70 Kg showed that the piezoelectric
output current varies from 1.2 milli-ampere to 1.6 milli-ampere. Although people have the same weight, but
different pressures generate different piezoelectric currents.
AA battery charging current test using forty piezoelectrics in parallel circuits is shown in Figure 8.
The picture shows that the forty piezoelectrics are tested by giving a pressure of 70 Kg weight. From the
graph, it can be seen that from fifty tests using pressure of people of 70 Kg showed that the piezoelectric

Int J Elec & Comp Eng, Vol. 8, No. 6, December 2018 : 4104 - 4110
Int J Elec & Comp Eng ISSN: 2088-8708  4109

output current varies from 9 volts to 20 volts. Although people have the same weight, but different pressures
generate different piezoelectric currents.

Figure 7. AA battery test using 40 piezoelectrics in parallel

Figure 8. AA battery test using 40 piezoelectrics in parallel

4. CONCLUSION
Based on the discussion and the analysis of the data that has been obtained, it can be concluded that
the current and voltage generated by piezoelectric is proportional to the size of the given force. The highest
current obtained is 938 micro amperes and the lowest is 641 micro amperes. While the highest voltage
obtained is 80 volts and the lowest is 67 volts. The utilization of electric current and voltage from the
piezoelectric with small current and large voltage for charging the battery can be carried out by limiting
piezoelectric output voltage using voltage regulator in accordance with the capacity of the battery used. This
results in a long time consumed in battery charging due to the small current cut by the regulator. The greater
the cutting voltage, the greater the discharged current. In addition, the frequency of stepping on the
piezoelectric floor affects on the battery charging. The higher the frequency, the more stable the current, and
the faster the battery charged. Piezoelectric current and voltage monitoring can be performed, but for
monitoring the battery capacity takes a considerably long time due to the very small battery capacity,
whereas microcontroller can only process with a minimum change of 4 mV.

Energy Harvesting on Footsteps Using Piezoelectric Based on Circuit.... (Slamet Suripto)

 4110  ISSN: 2088-8708

REFERENCES
[1] J. Kymissis, et al., “Parasitic power harvesting in shoes,” Digest of Papers. Second International Symposium on
Wearable Computers (Cat. No.98EX215), pp. 132-139, 1998.
[2] G. W. Taylor, et al., “The Energy Harvesting Eel: a small subsurface ocean/river power generator,” IEEE J. Ocean.
Eng., vol/issue: 26(4), pp. 539-547, 2001.
[3] S. Xu, et al., “Converter and controller for micro-power energy harvesting,” Twentieth Annual IEEE Applied Power
Electronics Conference and Exposition, 2005. APEC 2005, vol. 1, pp. 226-230, 2005.
[4] D. Blažević, et al., “Mechanical analysis of piezoelectric vibration energy harvesting devices,” The 33rd
International Convention MIPRO, pp. 122-126, 2010.
[5] J. G. Rocha, et al., “Energy Harvesting From Piezoelectric Materials Fully Integrated in Footwear,” IEEE Trans.
Ind. Electron., vol/issue: 57(3), pp. 813-819, 2010.
[6] H. G. Pisharody, “An optimal design for piezoelectric energy harvesting system,” ISGT2011-India, pp. 244-247,
2011.
[7] W. Wang, et al., “Vibration energy harvesting using piezoelectric circular diaphragm array,” 2011 International
Symposium on Applications of Ferroelectrics (ISAF/PFM) and 2011 International Symposium on Piezoresponse
Force Microscopy and Nanoscale Phenomena in Polar Materials, pp. 1-4, 2011.
[8] T. Alkhaddeim, et al., “Piezoelectric energy droplet harvesting and modeling,” 2012 IEEE Sensors, pp. 1-4, 2012.
[9] N. Rezaei, et al., “An Efficient Piezoelectric Windmill Topology for Energy Harvesting from Low Speed Air
Flows,” IEEE Trans. Ind. Electron., vol/issue: 62(6), pp. 1-1, 2015.
[10] X. D. Do, et al., “A Self-Powered High-Efficiency Rectifier With Automatic Resetting of Transducer Capacitance
in Piezoelectric Energy Harvesting Systems,” IEEE Trans. Very Large Scale Integr. Syst., vol/issue: 23(3), pp. 444-
453, 2015.
[11] A. Stein and H. Hofmann, “Resonant inverter design for stand-alone dynamic active piezoelectric energy
harvesting,” 2015 IEEE Applied Power Electronics Conference and Exposition (APEC), pp. 3265-3271, 2015.
[12] S. M. Shahriat, et al., “Design and implemantation of a piezoelectric energy harvesting system using a super
capacitor,” 2015 International Conference on Advances in Electrical Engineering (ICAEE), pp. 30-33, 2015.
[13] Iswanto, et al., “Path planning of decentralized multi-quadrotor based on fuzzy-cell decomposition algorithm,” 7th
International Conference on Mechanical and Manufacturing Engineering: Proceedings of the 7th International
Conference on Mechanical and Manufacturing Engineering, Sustainable Energy Towards Global Synergy, pp.
0200601-02006010, 2017.
[14] A. N. N. Chamim, et al., “Uninterruptable Power Supply based on Switching Regulator and Modified Sine Wave,”
Int. J. Electr. Comput. Eng., vol/issue: 7(3), pp. 1161-1170, 2017.
[15] A. N. N. Chamim, et al., “Atmega16 Implementation As Indicators Of Maximum Speed,” Int. J. Appl. Eng. Res.,
vol/issue: 11(15), pp. 8432-8435, 2016.
[16] R. Mubarok, et al., “Motorcycle-Security using Position Searching Algorithm Based on Hybrid Fuzzy-Dijkstra,”
Indones. J. Electr. Eng. Comput. Sci., vol/issue: 3(2), pp. 468-474, 2016.
[17] T. P. Tunggal, et al., “Pursuit Algorithm for Robot Trash Can Based on Fuzzy-Cell Decomposition,” Int. J. Electr.
Comput. Eng., vol/issue: 6(6), pp. 2863-2869, 2016.
[18] N. M. Raharja, et al., “Hovering Control of Quadrotor Based on Fuzzy Logic,” Int. J. Power Electron. Drive Syst.,
vol/issue: 8(1), pp. 492-504, 2017.

Int J Elec & Comp Eng, Vol. 8, No. 6, December 2018 : 4104 - 4110

View publication stats