Scribd
Upload
199 views

MCQs of Introduction To Metrology, Linear and Angular Measurement (Mechanical M

The document provides a list of multiple choice questions about metrology and measurement topics. It covers concepts like the purpose of instruments, definitions of measurement, measurand and output. The questions also address direct and indirect measurement methods, and components of a generalized measurement system like manipulator, detector-transducer and indicating units.

Uploaded by

Abhishek Yadav
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
199 views

MCQs of Introduction To Metrology, Linear and Angular Measurement (Mechanical M

The document provides a list of multiple choice questions about metrology and measurement topics. It covers concepts like the purpose of instruments, definitions of measurement, measurand and output. The questions also address direct and indirect measurement methods, and components of a generalized measurement system like manipulator, detector-transducer and indicating units.

Uploaded by

Abhishek Yadav
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 4

MCQs of Introduction to Metrology, Linear and Angular Measurement (Mechanical Measurement and Metrology - 3141901) | GTU MCQ

GTU MCQ
  Home   Bachelor of Engineering   Diploma in Engineering   About   Contact

Mechanical Measurement and Metrology (3141901)  MCQs

MCQs of Introduction to Metrology, Linear and Angular Measurement


Showing 1 to 10 out of 81 Questions 1
2
3
4
5
6

1. The purpose of instruments is to


(a) allow measurements to be made

(b) transmit the information

(c) change signals

(d) any of the above.

Show
Show Answer
Answer

2. The measurement refers to which of the following


(a) primary signal

(b) measured variable

(c) output

(d) all of the above.


2021 © Darshan Institute of Engineering & Technology, Rajkot (V2) Developed by  

Show
Show Answer
Answer

3. The measurement of a quantity


(a) is an act of comparison of an unknown quantity with another quantity

(b) is an act of comparison of an unknown quantity with a known quantity whose accuracy may be known or may not be known

(c) is an act of comparison of an unknown quantity with a predefined acceptable standard which is accurately known

(d) none of the above

Show
Show Answer
Answer

Measuring and testing software - Quality assurance


No complex in-house developments and evaluation programs. sonictc.de
OPEN

https://gtu-mcq.com/BE/Mechanical-Engineering/Semester-4/3141901/4991/MCQs?q=9aZHDjblmRk=[4/2/2022 10:33:36 PM]


MCQs of Introduction to Metrology, Linear and Angular Measurement (Mechanical Measurement and Metrology - 3141901) | GTU MCQ

4. In present day measurement systems


(a) direct methods are commonly used

(b) one of direst methods is limited but indirect methods are commonly used

(c) both direct and indirect methods are commonly used

(d) all of the above

Show
Show Answer
Answer

5. The measurand is
(a) output

(b) measured variable

(c) secondary signal

(d) any of the above

Show
Show Answer
Answer

6. The output stage of a generalized measurement system may comprise


(a) manipulator

(b) detector-transducer

(c) indicating or recording unit

(d) all of the above

Show
Show Answer
Answer

Measuring and testing software - Quality assurance


No complex in-house developments and evaluation programs. sonictc.de
OPEN

https://gtu-mcq.com/BE/Mechanical-Engineering/Semester-4/3141901/4991/MCQs?q=9aZHDjblmRk=[4/2/2022 10:33:36 PM]


MCQs of Introduction to Metrology, Linear and Angular Measurement (Mechanical Measurement and Metrology - 3141901) | GTU MCQ

7. The temperature measurement by a thermocouple is


(a) primary measurement

(b) secondary measurement

(c) tertiary measurement

(d) any one of above

Show
Show Answer
Answer

8. The function of the signal manipulating element in a generalized measurement system is to


(a) change the quantity under measurement to an analog signal

(b) change the magnitude of the input signal while retaining its identity

(c) to perform non-linear operation like filtering, chopping and clipping and clamping

(d) non of thee abovee

Show
Show Answer
Answer

9. The intermediate stage of an instrument is used to


(a) sense the primary (input) signal

(b) indicate and record the measurement

(c) amplify and transmit the secondary signal

(d) any of thee above

Show
Show Answer
Answer

https://gtu-mcq.com/BE/Mechanical-Engineering/Semester-4/3141901/4991/MCQs?q=9aZHDjblmRk=[4/2/2022 10:33:36 PM]


MCQs of Introduction to Metrology, Linear and Angular Measurement (Mechanical Measurement and Metrology - 3141901) | GTU MCQ

10. The degree of perfection used in instruments, the methods and the observations, is known as
(a) precision

(b) accuracy

(c) least count

(d) error

Show
Show Answer
Answer

Showing 1 to 10 out of 81 Questions 1


2
3
4
5
6

https://gtu-mcq.com/BE/Mechanical-Engineering/Semester-4/3141901/4991/MCQs?q=9aZHDjblmRk=[4/2/2022 10:33:36 PM]

You might also like