VT Exam 2020

1. The angle between the eye and the test surface for general visual testing should be
A) less than 60º
B) more than 60º
C) less than 30º
D) more than 30º

2. In flexible boroscope the image remains round and sharp until the tube is bent up to an
angle of
A) 30º
B) 45º
C) 60º
D) 90º

3. The leg of a concave fillet weld is:

A) the same as the size of a concave fillet weld.
B) larger than the size of a concave fillet weld.
C) equal to the actual throat dimension.
D) not applicable to a fillet weld.

4. A visual examination of a swing check valve would include:

A) an examination of the hinge pin.
B) an examination for wear on the disc.
C) an examination for wear on the seat.
D) all of the above.

5. The inverse square law states that the illuminance due to a point light source is:
A) inversely proportional to the distance from the light source.
B) directly proportional to the intensity of the li t source and inversely proportional to the
square of the distance from the source.
C) directly proportional to the square of the distance from the light source and inversely
proportional to the intensity of the source.
D) none of the above.

6. In Convex fillet welds, the shortest distance from the root of the weld to the face or the
Weld is called:
A) actual throat.
B) theoretical throat-
C) effective throat.
D) throat.

7. Which of following processes of undesirable metal wastage is characterized by

something other than wear:
A) Fretting
B) Erosion
C) Corrosion
D) Abrasion

8. An aid detecting thread from problems such as shaved and other threads that exhibit on
excessive narrowness of thread width is called:
A) Micrometer
B) Profile gauge
 C) Thread pitch gauge
D) Caliper
E) Pit gauge

9. Overlap is a weld profile condition where the angle formed at the junction between the
weld and base material is:
A) less than the 90 degrees from the plate surface.
B) equal to 90 degrees from the plate surface.
C) greater than the 90 degrees from the plate surface.
D) an internal flaw only detectable with ultrasonic testing.

10. General material loss in pumps could be caused:

A) lmpeller vibration
B) Vapor implosion on the trailing edge of the impeller
C) Surfaces in contact with relative motion
D) Chemical attack on pump internal any of these

11. The defect which can be located always by visual in a sand castings
A) Porosity
B) Lamellar

12. The three important properties of color are

A) Contrast, wave length, hue
B) Purity, hue, Contrast
C) Brightness, saturation, hue
D) Brightness, temp, hue

13. what are three Characteristics of surface texture?

a. roughness waveiness
b. profile scales and distortion
c. mechanic process and reflectivity
d. palplnaes and vaeeys
14. optical comparator and optical use over lays beside in review screen ----------,------or----
-----
a. linear , purch , profile
b. profile , linear , thermal
c. linear, angular and profile
d. linear , profile and reflection

15. you are visual examination a swing check valve which of following condition should
looking for (in disc – grading system – wear and seat – leakage)
a. 1:2
b. 2:3
c. 3
d.4
16. the fillet weld gauges manufacturing increments of
a.1/4
b. 1/16
c. 1/2
d. 3/16

17. What need to on hallo contractors that may have contain flammable Gases before
apply heat
a. vent fill internal gases
b. vent the container with halogen
c. place of container storage for three months

18. how is average roughness (RA)define it

a. average high test
b. average depth valley
c. average distance to main line

19. the term use to descript the condition wear eyes is in adapt it state
a. alnberitan actual
b. accommodation
c. scotopic vision

20. what is the purpose destroyed stretched wire of renown diameter and underwater of
nuclear contents
A visual resolution calibration
B discontinuity measurement
C marking area of interest
D check for expensive glare

21. the B31.8 this published by

a. api
b.nsce
c.aws
d.ASME
22. blister on rolled plate are describe with
a. an asid eating visual inspection
b. normal in cadence direct lighting
c. low indication side lighting
d. 50X magnifier

23. when mix quantity of material etchants the use of space mandatory
a. eye station
b. exhaust wood
c. safety shower
d. fire extinguisher

24. syflemons of nausea dizziness fever is caused by fumes containing.

a. chromium
b. copper , lead and nickel
c. zinc
d. arsenic
25. Video camera image is reserved in
Ans: frame

26. Inverse square law: Source 10in. 100 lumens, 30in.?

1/102 : 100 = 1/302 : X X x 1/100 = 100 x 1/900 X = 100/9 = 11.1 lumen