Scribd
Upload
3K views8 pages

Como Leer Codigos HAMM

This document provides instructions for reading error codes on H-Series compactors from HAMM AG. It explains that the ignition must be on to view error codes, and that codes will appear in displays 101, 106, 108 or 110. Pushing the MODE button when the control lamp is flashing will cycle through the error codes. The first code shown will be the error number, and pushing MODE again will show the failure mode indicator number. The document provides this process for both the EMR4 and RC28-14 systems.

Uploaded by

Vladimir Valentin Lopez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
3K views8 pages

Como Leer Codigos HAMM

This document provides instructions for reading error codes on H-Series compactors from HAMM AG. It explains that the ignition must be on to view error codes, and that codes will appear in displays 101, 106, 108 or 110. Pushing the MODE button when the control lamp is flashing will cycle through the error codes. The first code shown will be the error number, and pushing MODE again will show the failure mode indicator number. The document provides this process for both the EMR4 and RC28-14 systems.

Uploaded by

Vladimir Valentin Lopez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 8

Readout of error codes H-Series

Series 3000 (RC28)

Readout of error codes


H-Series
Series 3000 (RC28)

HAMM AG 1/8 # 2285023


01.12.2014
Readout of error codes H-Series
Series 3000 (RC28)

Inhaltsverzeichnis / Contents:

1  Instructions for use ..................................................................... 3 


1.1  Liability exclusion ................................................................................................... 3 
1.2  Important symbols in the manual: ......................................................................... 3 
2  Readout of error codes ............................................................... 4 
2.1  Important information ............................................................................................. 4 
2.1  Displays for error codes ......................................................................................... 4 
3  Error reporting EMR4 .................................................................. 5 
4  Identification of errors ................................................................ 6 
5  Error reporting RC28-14 ............................................................. 7 
6  Identification errors .................................................................... 8 

HAMM AG 2/8 # 2285023


01.12.2014
Readout of error codes H-Series
Series 3000 (RC28)

1 Instructions for use


1.1 Liability exclusion
This manual should assist service technicians with the readout of error codes via the
display. The general safety and accident prevention regulations apply. Company HAMM
AG cannot be made liable for occurrences caused by the application of the steps
recommended in this document.

1.2 Important symbols in the manual:

! Security advices

9 Necessary information

; General information

HAMM AG 3/8 # 2285023


01.12.2014
Readout of error codes H-Series
Series 3000 (RC28)

2 Readout of error codes


2.1 Important information

9 Ignition on!

8 Diesel engine off!!!

2.1 Displays for error codes

Display 101

Display 106

Display 108

Display 110

HAMM AG 4/8 # 2285023


01.12.2014
Readout of error codes H-Series
Series 3000 (RC28)

3 Error reporting EMR4

Control lamp
(240) in the
display lights up

By pushing the
MODE button
when control lamp
(240) is flashing,
the displays
(101,106,108,110)
are switched over
to the diagnostic
mode.
Each actuation of
the MODE button,
the Display
switches one step
forward.

The button is only active when the control lamp (240) is flashing.

HAMM AG 5/8 # 2285023


01.12.2014
Readout of error codes H-Series
Series 3000 (RC28)

4 Identification of errors

“Err S1“ = SPN 1 ----> push MODE button ----> „Err F1“ = FMI 1----> push….

HAMM AG 6/8 # 2285023


01.12.2014
Readout of error codes H-Series
Series 3000 (RC28)

5 Error reporting RC28-14

Control lamp
(240) in the
display lights up

By pushing the
MODE button
when control lamp
(240) is flashing,
the displays
(101,106,108,110)
are switched over
to the diagnostic
mode.
Each actuation of
the MODE button,
the Display
switches one step
forward.

The button is only active when the control lamp (240) is flashing.

HAMM AG 7/8 # 2285023


01.12.2014
Readout of error codes H-Series
Series 3000 (RC28)

6 Identification errors

“Err H“ = internal ----> push MODE button ---->

HAMM AG 8/8 # 2285023


01.12.2014

You might also like