Scribd
Upload
47 views3 pages

Question Pre Final

This document contains a pre-final assignment for a Microprocessor Interfacing and Embedded Systems course. It includes two main questions to answer. The first asks the student to (1) design logic to access an 8255A chip, (2) initialize control registers, (3) create string variables, (4) compare input and reversed strings, and (5) light LEDs accordingly to check for palindromes. It also asks the student to answer true/false questions about string instructions, timers, and data movement instructions. The second main question asks the student to (1) access and configure individual bits as inputs, and (2) use timers to energize a relay coil every 10 milliseconds by (i) initializing a

Uploaded by

Salman Reza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
47 views3 pages

Question Pre Final

This document contains a pre-final assignment for a Microprocessor Interfacing and Embedded Systems course. It includes two main questions to answer. The first asks the student to (1) design logic to access an 8255A chip, (2) initialize control registers, (3) create string variables, (4) compare input and reversed strings, and (5) light LEDs accordingly to check for palindromes. It also asks the student to answer true/false questions about string instructions, timers, and data movement instructions. The second main question asks the student to (1) access and configure individual bits as inputs, and (2) use timers to energize a relay coil every 10 milliseconds by (i) initializing a

Uploaded by

Salman Reza
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

Department of Electrical & Computer Engineering (ECE)

North South University


Course Code: 331, Section: 5,6 (Noon)
Course Title: Microprocessor Interfacing & Embedded System
Pre Final Assignment, Summer 2019

Name:
Student ID and section:

Answer All

1. Answer all the questions given below. [10]

(a) Consider the following 8086 interfacing problem. [1+1+1+1+1]

The LED array connected to Port A will light up if the input string is a Palindrome

Ex. of Palindrome: Input String- "abba" ; Output: String is palindrome

Input String- "abbc" ; Output: String is not palindrome

(i) Construction of the logic circuit to access 8255A


(ii) Initialization of the control registers for the designated operation
(iii) Creation of the string variables
(iv) Comparison between the input string and reversed string
(v) Lighting up the LED array
Hints: Use LEA, SI and DI to access and compare the input and reversed strings

(b) Write answer of T or F for each question given below [1+1+1+1+1]

(i) Move string instructions are used to copy an array from one location to another location
(ii) There are two 8 bit timers in 8051 microcontroller
(iii) Timers can only be used for creating delay loops but not for counting
(iv) The MOVSB instruction tells the assembler to be moved string as words; the MOVSW
implies the string is to be moved as bytes.
(v) CMPSB compares two bytes in given addresses and sets the flag accordingly

2. Answer all the questions given below

(a) Explain how to access and configure individual bit as input for 8051 application.
[2.5+2.5]

(b) Consider the following 8051 interfacing problem. Crystal frequency: 11.059MHz.The
relay coil is to be energized at an interval of 10 ms. Use timer routine to implement the
operation. [1+1+1+1+1]

i) Initialize TMOD for timer 0 , mode 1 operation


ii) Initialize TH0 and TL0 for 10 ms delay
iii) Construct the delay loop with appropriate timer flag setting
iv) Access and configure relevant pin as needed
v) Call back delay loop from the main function as needed

You might also like