Shear & Moment in Beams

DEFINITION OF A BEAM

A beam is a bar subject to forces or couples that lie in a plane containing the

longitudinal of the bar. According to determinacy, a beam may be determinate or

indeterminate.

STATICALLY DETERMINATE BEAMS

Statically determinate beams are those beams in which the reactions of the supports

may be determined by the use of the equations of static equilibrium. The beams shown

below are examples of statically determinate beams.

STATICALLY INDETERMINATE BEAMS

If the number of reactions exerted upon a beam exceeds the number of equations in

static equilibrium, the beam is said to be statically indeterminate. In order to solve the

reactions of the beam, the static equations must be supplemented by equations based

upon the elastic deformations of the beam.

The degree of indeterminacy is taken as the difference between the umber of reactions

to the number of equations in static equilibrium that can be applied. In the case of the

propped beam shown, there are three reactions R1, R2, and M and only two equations

(∑M = 0 and sum;Fv = 0) can be applied, thus the beam is indeterminate to the first

degree (3 – 2 = 1).
TYPES OF LOADING

Loads applied to the beam may consist of a concentrated load (load applied at a point),

uniform load, uniformly varying load, or an applied couple or moment. These loads are

shown in the following figures.

carries a uniform load of w (N/m) throughout its

length and is held in equilibrium by reactions R1

and R2. Assume that the beam is cut at point C a

distance of x from he left support and the portion of

the beam to the right of C be removed. The portion

removed must then be replaced by vertical

shearing force V together with a couple M to hold

the left portion of the bar in equilibrium under the

action of R1 and wx. The couple M is called the resisting moment or moment and the

force V is called the resisting shear or shear. The sign of V and M are taken to be

positive if they have the senses indicated above.

Solved Problems in Shear and Moment Diagrams

Write shear and moment equations for the beams in the following problems. In each

problem, let x be the distance measured from left end of the beam. Also, draw shear

and moment diagrams, specifying values at all change of loading positions and at points

of zero shear. Neglect the mass of the beam in each problem.

Problem 403

Beam loaded as shown in Fig. P-403.

Beam loaded as shown in Fig. P-404.

Solution 404
Problem 405

Beam loaded as shown in Fig. P-405.

Solution 405
Problem 406

Beam loaded as shown in Fig. P-406.

Solution 406
Problem 407

Beam loaded as shown in Fig. P-407.

Solution 407
Problem 408

Beam loaded as shown in Fig. P-408.

Solution 408
 Problem 409

Cantilever beam loaded as shown in Fig. P-409.

Solution 409
Problem 410

Cantilever beam carrying the uniformly varying load shown in Fig. P-410.

Solution 410
Problem 411

Cantilever beam carrying a distributed load with intensity varying from wo at the free

end to zero at the wall, as shown in Fig. P-411.

Solution 411
Problem 412

Beam loaded as shown in Fig. P-412.

Solution 412
Problem 413

Beam loaded as shown in Fig. P-413.

Solution 413
Problem 414

Cantilever beam carrying the load shown in Fig. P-414.

Solution 414
Problem 415

Cantilever beam loaded as shown in Fig. P-415.

Solution 415
Problem 416

Beam carrying uniformly varying load shown in Fig. P-416.

Beam carrying the triangular loading shown in Fig. P- 417.

Solution 417
Problem 418

Cantilever beam loaded as shown in Fig. P-418.

Solution 418

Problem 419

Beam loaded as shown in Fig. P-419.

A total distributed load of 30 kips supported by a uniformly distributed reaction as

shown in Fig. P-420.

Write the shear and moment equations as functions of the angle θ for the built-in arch

shown in Fig. P-421.

Solution 421
Problem 422

Write the shear and moment equations for the semicircular arch as shown in Fig. P-422

if (a) the load P is vertical as shown, and (b) the load is applied horizontally to the left

at the top of the arch.

Solution 422
Relationship between Load, Shear, and Moment
The vertical shear at C in the figure shown in previous section is taken as

where R1 = R2 = wL/2

If we differentiate M with respect to x:

thus,

Thus, the rate of change of the bending moment with respect to x is equal to the

shearing force, or the slope of the moment diagram at the given point is the

shear at that point.

Differentiate V with respect to x gives

Thus, the rate of change of the shearing force with respect to x is equal to the load or

the slope of the shear diagram at a given point equals the load at that point.

PROPERTIES OF SHEAR AND MOMENT DIAGRAMS

The following are some important properties of shear and moment diagrams:

1. The area of the shear diagram to the left or to the right of the section is equal to

the moment at that section.

2. The slope of the moment diagram at a given point is the shear at that point.

3. The slope of the shear diagram at a given point equals the load at that point.
 4. The maximum moment occurs at the point of zero shears.

This is in reference to property number 2, that when the

shear (also the slope of the moment diagram) is zero, the

tangent drawn to the moment diagram is horizontal.

5. When the shear diagram is increasing, the moment diagram is concave upward.

6. When the shear diagram is decreasing, the moment diagram is concave

downward.

SIGN CONVENTIONS

The customary sign conventions for shearing force and bending moment are

represented by the figures below. A force that tends to bend the beam downward is said

to produce a positive bending moment. A force that tends to shear the left portion of

the beam upward with respect to the right portion is said to produce a positive shearing

force.

An easier way of determining the sign of the bending moment at any section is that

upward forces always cause positive bending moments regardless of whether they act

to the left or to the right of the exploratory section.

Solved Problems in Relationship between Load, Shear, and Moment

INSTRUCTION

Without writing shear and moment equations, draw the shear and moment diagrams for

the beams specified in the following problems. Give numerical values at all change of

loading positions and at all points of zero shear. (Note to instructor: Problems 403 to

420 may also be assigned for solution by semi graphical method describes in this

article.)
Problem 425

Beam loaded as shown in Fig. P-425.

Solution 425
Problem 426

Cantilever beam acted upon by a uniformly distributed load and a couple as shown in

Fig. P-426.

Solution 426
Problem 427

Beam loaded as shown in Fig. P-427.

Solution 427
Problem 428

Beam loaded as shown in Fig. P-428.

Solution 428
Problem 429

Beam loaded as shown in Fig. P-429.

Solution 429
Problem 430

Beam loaded as shown in P-430.

Solution 430
Problem 431

Beam loaded as shown in Fig. P-431.

Solution 431
Problem 432

Beam loaded as shown in Fig. P-432.

Solution 432
Problem 433

Overhang beam loaded by a force and a couple as shown in Fig. P-433.

Solution 433
Problem 434

Beam loaded as shown in Fig. P-434.

Solution 434
Problem 435

Beam loaded and supported as shown in Fig. P-435.

Solution 435
Problem 436

A distributed load is supported by two distributedreactions as shown in Fig. P-436.

Solution 436
Problem 437

Cantilever beam loaded as shown in Fig. P-437

Solution 437
Problem 438

The beam loaded as shown in Fig. P-438 consists of two segments joined by a

frictionless hinge at which the bending moment is zero.

Solution 438
Problem 439

A beam supported on three reactions as shown in Fig. P-439 consists of two segments

joined by frictionless hinge at which the bending moment is zero.

Solution 439
Problem 440

A frame ABCD, with rigid corners at B and C, supports the concentrated load as shown

in Fig. P-440. (Draw shear and moment diagrams for each of the three parts of the

frame.)

Solution 440
Problem 441

A beam ABCD is supported by a roller at A and a hinge at D. It is subjected to the loads

shown in Fig. P-441, which act at the ends of the vertical members

BE and CF. These vertical members are rigidly attached to the beam at B and C. (Draw

shear and moment diagrams for the beam ABCD only.)

Solution 441
Problem 442

Beam carrying the uniformly varying load shown in Fig. P-442.

Solution 442
Problem 443

Beam carrying the triangular loads shown in Fig. P-443.

Solution 443
Problem 444

Beam loaded as shown in Fig. P-444.

Solution 444
Problem 445

Beam carrying the loads shown in Fig. P-445.

Solution 445
Problem 446

Beam loaded and supported as shown in Fig. P-446.

Solution 446
Finding the Load & Moment Diagrams with Given Shear
Diagram

INSTRUCTION

In the following problems, draw moment and load diagrams corresponding to the given

shear diagrams. Specify values at all change of load positions and at all points of zero

shear.

Problem 447

Shear diagram as shown in Fig. P-447.

Solution 447
Problem 448

Shear diagram as shown in Fig. P-448.

Solution 448
Problem 449

Shear diagram as shown in Fig. P-449.

Solution 449
Problem 450

Shear diagram as shown in Fig. P-450.

Solution 450
Problem 451

Shear diagram as shown in Fig. P-451.

Solution 451