Thick film shunt resistors <face down type>

UCR series
Datasheet

● Features
1)Very-low ohmic resistance from 11mΩ is in lineup by thick-film resistive element.
2)Resistive element is located at bottom side, which reduces the resistance shift
during mounting process.
3)ROHM's unique structure achieved improvement of heat.
4)ROHM resistors have obtained ISO9001 / IATF16949 certification.
5)Corresponds to AEC-Q200.UCR03 (under 100mΩ or less) are unsupprted.

● Products list
Size Rated Resistance Temperature Operating Automotive
Power Resistance range temperature
Part No. (70℃) tolerance coefficient range grade
(mm) (inch) available
(W) (ppm / ℃) (Ω) (℃)
F ( ±1% )
UCR006 0603 0201 0.1
J ( ±5% )
0～300 0.100≦R＜1 (E24series) -55 ～+155 Yes

0～300 0.068≦R＜0.100 (E24series)

F ( ±1% )
UCR01 1005 0402 0.125 J ( ±5% ) 0～250 0.100≦R＜0.220 (E24series) -55 ～+155 Yes
0～200 0.220≦R≦0.910 (E24series)
0～250 0.020≦R＜0.050 (E24series)
0.25 F ( ±1% ) 0～200 0.050≦R＜0.100 (E24series)
J ( ±5% )
UCR03 1608 0603 0～150 0.100≦R≦0.200 (E24series) -55 ～+155 Yes*

0.2 F ( ±1% ) 0～150 0.220≦R≦0.910 (E24series)

J ( ±5% )
250±200 0.011≦R＜0.020 (E24series)
F ( ±1% )
UCR10 2012 0805 0.33 J ( ±5% ) 0～250 0.020≦R≦0.047 (E24series) -55 ～+155 Yes
0～150 0.047＜R≦0.1 (E24series)
0.5 0～350 0.011≦R＜0.020 (E24series)
UCR18 3216 1206 (★1) F ( ±1% ) (E24series) -55 ～+155 Yes
J ( ±5% ) 0～200 0.020≦R≦0.039
0.5 0～150 0.039＜R≦0.1 (E24series)
* Design and specifications are subject to change without notice. ★:Under development
Carefully check the specification sheet supplied with the product before using or ordering it.
* UCR03 correspounds only to 100mΩ or more.
● Part Number Description
UCR 1 0 EVH J L R1 0
Part No. Size (mm [inch]) Packaging specifications code Resistance Special Nominal resistance
006(0603 [0201]) Packaging Quantity tolerance part code Resistance code,3 or 4 digits.
UCR Part No. Code specifications / Reel
01(1005 [0402]) F ( ±1% ) S： 0.011 ～ Resistance
(Thick film tolerance Resistance
shunt 03(1608 [0603]) Paper tape J ( ±5% ) 0.091Ω +
UCR006 YVP 15,000 code
resistors ( 2mm Pitch) L： 0.1Ω ～ Specialcode
10(2012 [0805])
face down 18(3216 [1206]) FS,FL,JS ： 4 digits
type) Paper tape
UCR01 MVP ( 2mm Pitch)
10,000
JL ： 3 digits
EWP
(20mΩ～47mΩ) Paper tape
UCR03 ( 4mm Pitch) 5,000
EVP
(51mΩ～910mΩ)

Paper tape
UCR10 EVH ( 4mm Pitch)
5,000
Paper tape
UCR18 EVH ( 4mm Pitch)
5,000

www.rohm.com
© 2020 ROHM Co., Ltd. All rights reserved. 1/4
2020.07 - Rev.G
UCR series Datasheet

● Chip resistor dimensions and markings

■ UCR006/01 ■ UCR03(20mΩ≦R<50mΩ) ■ UCR10/18

■ UCR03(50mΩ≦R≦910mΩ)
<Marking method>
There are three or four digits used for
the calculation number according to
IEC code and “R”is used for the
decimal point.
Ex.) 4digits······0.1Ω =R100
3digits······0.1Ω =R10

(Unit:mm)
Part No. (mm) (inch) L W t a b Marking
existence

UCR006 0603 0201 0.62±0.05 0.32±0.05 0.24±0.05 0.18±0.10 0.22±0.10 No

UCR01 1005 0402 1.00±0.10 0.55±0.10 0.37±0.05 0.28±0.10 0.34±0.10 No

UCR03 1608 0603 1.60±0.10 0.87±0.10 0.50±0.10 0.45±0.20 0.45±0.20 No

UCR10 2012 0805 2.00±0.10 1.25±0.10 0.55±0.10 0.24±0.20 0.50±0.20 Yes

UCR18 3216 1206 3.20±0.15 1.60±0.15 0.55±0.10 0.30±0.20 0.90±0.25 Yes

● Land pattern example

(Unit:mm)
Dimensions
Part No.
A B C D

UCR006 0.3 0.84 0.3 0.27

UCR01 0.5 1.8 0.5 0.65

UCR03 0.5 2.5 0.9 1.0

UCR10 0.8 3.4 1.3 1.3

UCR18 1.4 4.0 1.8 1.3

www.rohm.com
© 2020 ROHM Co., Ltd. All rights reserved. 2/4
2020.07 - Rev.G
UCR series Datasheet

● Derating curve
When the ambient temperature exceeds 70°C, power dissipation must be adjusted according to the derating curves below.

■UCR006/01/03/10/18

● Characteristics
Test items Guaranteed value Test conditions
20℃
Measuring method : Measure Bottom termination
by 4 proves.

Resistance See P.1

Variation of resistance
with temperature See P.1 Measurement：+25/-55, +25/+125℃

Overload ±2.0％ Rated voltage(current)×2.5， 2s

Anew uniform coating of minimum
Rosin-ethanol solution (25% mass)
of 95% of the surface being Soldering condition：245±5℃
Solderability
immersed and no soldering Duration of immersion：2.0±0.5s
damage.
Resistance to ±1.0％ Soldering condition：260±5℃
soldering heat No remarkable abnormality on the appearance. Duration of immersion：10±1s
Rapid change of
temperature ±1.0％ Test temp：-55℃～+125℃ 5cycles

40℃，93％(Relative humidity)
Damp heat, steady state ±3.0％
Test time：1,000h
70℃,Rated voltage
Endurance at 70℃ ±3.0％ 1.5h:ON－0.5h:OFF
Test time：1,000h
155℃
Endurance ±3.0％
Test time：1,000h

Resistance to solvent ±0.5％ 23±5℃, Immersion cleaning, 5±0.5min

Solvent: 2-propanol

Bend strength of
the end face plating Without open. -

*Please contact us for guarantee of the test conditions other than those described above. Compliance Standard(s) : IEC60115-8
JIS C 5201-1

www.rohm.com
© 2020 ROHM Co., Ltd. All rights reserved. 3/4
2020.07 - Rev.G
UCR series Datasheet
● Tape dimensions
■Paper tape (Unit : mm)
Part No. W F E A0 B0
UCR006 8.0±0.1 3.5±0.05 1.75±0.03 0.39±0.02 0.7±0.02

UCR01 8.0±0.3 3.5±0.05 1.75±0.1 0.7±0.1 1.2±0.10

UCR03 8.0±0.3 3.5±0.05 1.75±0.1 1.1±0.1 1.9±0.1

UCR10 8.0±0.3 3.5±0.05 1.75±0.1 1.65 +0.2 2.4 +0.2

-0.1 -0.1
UCR18 8.0±0.3 3.5±0.05 1.75±0.1 1.95 +0.1 3.5 +0.15
-0.05 -0.05

Part No. D0 P0 P1 P2 T2
UCR006 Φ1.5±0.03 4.0±0.1 2.0±0.05 2.0±0.05 MAX0.46
+0.1
UCR01 Φ1.5 4.0±0.1 2.0±0.05 2.0±0.05 MAX1.1
0
UCR03 Φ1.5 +0.1 4.0±0.1 4.0±0.05 2.0±0.05 MAX1.1
0
UCR10 Φ1.5 +0.1 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1
0
UCR18 Φ1.5 +0.1 4.0±0.1 4.0±0.1 2.0±0.05 MAX1.1
0

● Reel dimensions
Using two kinds of reels for taping.

(Unit : mm)
Part No. A B C D
UCR006
UCR01
0 +1.0 +1.0
UCR03 Φ180 Φ60 9 Φ13±0.2
-1.5 0 0
UCR10
UCR18

www.rohm.com
© 2020 ROHM Co., Ltd. All rights reserved. 4/4
2020.07 - Rev.G
 Notice
Precaution on using ROHM Products
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1),
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN USA EU CHINA
CLASSⅢ CLASSⅡb
CLASSⅢ CLASSⅢ
CLASSⅣ CLASSⅢ

2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure

3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used.
However, recommend sufficiently about the residue.); or Washing our Products by using water or water-soluble
cleaning agents for cleaning residue after soldering
[h] Use of the Products in places subject to dew condensation

4. The Products are not subject to radiation-proof design.

5. Please verify and confirm characteristics of the final or mounted products in using the Products.

6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.

7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.

8. Confirm that operation temperature is within the specified range described in the product specification.

9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.

Precaution for Mounting / Circuit board design

1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.

2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.

For details, please refer to ROHM Mounting specification

Notice-PAA-E Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.

2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.

Precaution for Electrostatic

This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).

Precaution for Storage / Transportation

1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl 2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic

2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.

3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.

4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.

Precaution for Product Label

A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.

Precaution for Disposition

When disposing Products please dispose them properly using an authorized industry waste company.

Precaution for Foreign Exchange and Foreign Trade act

Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.

Precaution Regarding Intellectual Property Rights

1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.

Notice-PAA-E Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
 Datasheet

General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall n ot be in an y way responsible or liabl e for fa ilure, malfunction or acci dent arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.

2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.

3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for an y damages, expenses or losses incurred b y you or third parties resulting from inaccur acy or errors of or
concerning such information.

Notice – WE Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

ROHM Semiconductor:
UCR03EVPFSR050 UCR10EVHFSR050 UCR03EVPFSR056 UCR18EVHFSR100 UCR10EVHFLR150
UCR18EVHFSR050 UCR18EVHJSR050 UCR03EVPJSR082 UCR03EWPFSR036 UCR10EVHFSR100
UCR01MVPFSR075 UCR01MVPFSR091 UCR01MVPFSR110 UCR03EVPFLR051