P1 Panelboards

Features
P1 panelboards are pre-engineered to • Three circuit sizes means only three box
accept the most common modifications heights, regardless of main configuration
without increasing box height. The through 250 amp and an additional three
enclosure size is determined by the number circuit version and boxes available at
of circuits as shown in the Main Lug Table 400 amps.
P1-5 or the Main Circuit breaker Table
P1-3. All P1 Main Lug or main breaker • Suitable for use as service entrance given
panelboards have space built-in to accept compliance with NEC.
either feed-thru lugs equal to the panel • Bonding provisions are shipped with
rating, one subfeed circuit breaker up to each panel.
250 amperes or a surge suppressor (TVSS)
without increasing box height. • 240V and 480V / 277V for versions utilize
identical boxes and fronts.
Note the following features, all found in the
innovative P1 lighting panelboards: Voltage – 480Y / 277 Vac max.
250V Vdc max.
• Symmetrical interiors - No top or bottom.
To change from top to bottom (or vice Amperage – 400 amp max.
versa), simply invert the interior. The Short Circuit Rating – 200 KAIC max.
deadfront labeling is always right-side up. symmetrical or equal to the lowest rated
• First in the - industry Ratings of 125 device installed unless a series rating is
through 400A main lug and main breaker. indicated. Panels with subfeed or feed-thru
Field convertible from main lug ro main lugs without a main device, circuit breaker,
breaker and vice versa - with no increase or fusible unit, are limited to a three-cycle
in enclosure height. rating. The three-cycle rating for the P1
panel is limited to 22 KAIC. Note that the
• Field adaptability of feed-thru lugs or main device may be mounted remote from
subfeed circuit breaker without increasing the panel.
enclosure size.
Bussing – The P1 panel meets the majority
• Neutral system is field upgradeable to of the market’s bussing requirements.
200% capacity - another industry first. The standard bussing is temperature
rated aluminum. The rating is per the
requirements of UL 67 - the standard for
panelboards. All aluminum bussing is tin-
plated. Optional bussing for the P1 panel is
temperature rated copper. The copper bus
option for the panel is tin-plated.
Weight – Approximate
Total panelboard weight when filled
with a normal quantity of breakers and
accessories is about 3 lbs. (1 kg) per inch
(54g per mm) of box height.

Box Material Gauge

Width Height (in.) Gauge Steel
20” 32, 38, 44 #16
56, 62, 68
Trim Material Gauge
Width Height (in.) Gauge Steel
20” 32, 38, 44 #14
56, 62, 68

Lighting Panelboards

www.usa.siemens.com/panelboards
Main Lug or Main Breaker
Maximum Main Breaker Maximum Box Height Connections Suitable
Ampere Rating Type Number of Poles Inches (mm) for Cu or Al
BL, BLH 32 (813) #8-#6 AWG Cu or Al
100 HBL 38 (965) #8-6 AWG Cu or #8-4 AWG Al
BQD 44 (1118) #8-#1 AWG Cu or #6-#1/0 AWG Al
32 (813)
15-30 amp #14-#6 Cu or #12-#6 Al
NGB 38 (965)
35-125 amp #6-1/0 Cu. #4-2/0 Al.
44 (1118)
125
EDZ, ED4 #14-#10 AWG Cu or #12-10 AWG Al
32 (813)
ED6, HED4 #3-3/0 Cu or
18 38 (965)
HED6 44 (1118) #1-2/0 Al
30
Q12 42 32 (813) #6 AWG-300 Kcmil (Cu)
225 QJH2 38 (965) or
QJ2-H 44 (1118) #4 AWG-300 Kcmil (Al)
FXD6 32 (813) #6 AWG-350 Kcmil (Cu)
250 FD6 38 (965) or
HFD6, HFXD6 44 (1118) #4 AWG-350 Kcmil (Al)
32 (813)
≤250 MLO 38 (965) (1) #4-350 Kcmil
44 (1118)
JD6, JXD6 56 (1422) 3/0-500 Kcmil (Cu)
HJD6 62 (1575) or
HJXD6 18 68 (1727) 4/0-500 Kcmil (Al)
400 30
42 56 (1422) (1) 250 -600 Kcmil
MLO 62 (1575) or
68 (1727) (2) #3/0-500 Kcmil

Side Gutter Wiring Space

Inches (mm) (Fig. P1-1) Fig. P1-1 Main Device Gutter
Panel
Reference Panel Width 24” BL, BLH, HBL BL, BLH, HBL
Letter Width 20” Optional A A
BLF, BLHF BLF, BLHF
A 6.375 (162) 8.375 (213) B BQD BQD B
B 5.500 (140) 7.500 (191) C NGB NGB C
C 5.000 (127) 7.000 (178) D ED2, ED4, ED6, HED4, HED6
Da 6.125 (156) 8.125 (206) E QJ2, QJH2, QJ2-H
Ea 6.500 (165) 8.500 (216) F FXD6, FD6, HFD6
Fa 5.250 (133) 7.250 (184)
a Subfeed mounting limit 1 per panel Panel Width
20 in. (508 mm)

Main Breaker Gutter Dimensions Inches (mm)

Gutter Neutral Location
Main Breaker 20” wide box 24” wide box 20” wide box
BL, BLH, HBL, BQD 8.500 (216) 10.500 (267) 11.500 (292)
ED2, ED4, ED6, HED4 6.125 (156) 8.125 (206) 11.500 (292)
QJ2, QJH2, QJ2-H 6.500 (165) 8.500 (216) 11.500 (292)
FD6, FXD6, HFD6 5.250 (133) 7.250 (184) 11.500 (292)
JD6, JXD6  15.000 (381) 15.000 (381) 26.750 (680)
a JD frame mounted vertically.

Typical Panelboard Wiring Diagrams

Breaker Mounting Kit – Main or Subfeed w/o Breaker 200% Neutral Lug Kits – 250A
Amp Catalog Number
Rating Breaker Frames Service Number of Circuits Description Catalog Number
BL, BLH, HBL 1 Phase MBKBL1 2 Branch Neutral Strips,
18 2NLK18
100 3 Phase MBKBL3 2 Main Neutral Lug, Hardware
BQD 3 Phase MBKBC3 2 Branch Neutral Strips,
30 2NLK30
NGB 1 Phase MBKNB1 2 Main Neutral Lug, Hardware
3 Phase MBKNB3 2 Branch Neutral Strips,
125 42 2NLK42
ED2, ED4, ED6, HED4, HED6 1 Phase MBKED1 2 Main Neutral Lug, Hardware
3 Phase MBKED3
QJ2, QJH2, QJ2-H 1 Phase MBKQJ1
225 200% Neutral Lug Kits – 400A
3 Phase MBKQJ3
Number
FXD6, FD6, HFD 1 Phase MBKFD1
250 of Circuits Description Catalog Number
3 Phase MBKFD3
2 Branch Neutral Strips,
JD2, JD6, JXD6, HJD6, HJXD6 1 Phase MBKJD1 18 42NLK18
400a 4 Main Neutral Lug, Hardware
3 Phase MBKJD3
2 Branch Neutral Strips,
30 42NLK30
4 Main Neutral Lug, Hardware
2 Branch Neutral Strips,
42 42NLK42
4 Main Neutral Lug, Hardware
Lug Kits – Main or Feed-thru
Amp Catalog
Rating Material Wire Range Service Number Copper Neutral Lug Kits – 250A and 400A
Al (1) #6 AWG-350 Kcmil (Cu or Al) 1 Phase MLKA1 Number
(1) #6 AWG-350 Kcmil (Cu or Al) 3 Phase MLKA3 of Circuits Description Catalog Number
250
Cu (1) #6 AWG-350 Kcmil (Cu or Al) 1 Phase MLKC1 2 Branch Neutral Strips,
18 CNLK18
(1) #6 AWG-350 Kcmil (Cu or Al) 3 Phase MLKC3 1 Main Neutral Lug, Hardware
Al (2) 3/0 - (1) 600 Kcmil 1 Phase 4MLKA1 2 Branch Neutral Strips,
30 CNLK30
(2) 3/0 - (1) 600 Kcmil 3 Phase 4MLKA3 1 Main Neutral Lug, Hardware
400
Cu (2) 3/0 - (1) 600 Kcmil 1 Phase 4MLKC1 2 Branch Neutral Strips,
42 CNLK42
(2) 3/0 - (1) 600 Kcmil 1 Phase 4MLKC3 1 Main Neutral Lug, Hardware

Branch Circuit Breakers

Maximum Interrupting Rating (kA)
Max. No.
Amp Breaker of Amp Volts – AC DC Load
Rating Type Poles Rating 120 120/240 240 277 480 600 250 Connectors
1 15 - 70 10 – – – – – –
BL 2 15 - 100 – 10 – – – – –
3 15 - 100 – – 10 – – – –
1 15 - 30 10 – – – – – –
BL, HD
2 15 - 30 – 10 – – – – –
BLR 2 15 - 100 – – 10 – – – –
1 15 - 30 10 – – – – – –
BLE
2 15 - 60 – 22 – – – – –
15-20A #14-#10 AWG Cu
1 15 - 30 22 – – – – – –
BLEH #12-#10 AWG Al
2 15 - 60 – 10 – – – – – 25-35A #8-#6 AWG Cu
1 15 - 30 10 – – – – – – #8-#6 AWG Al
BLF
2 15 - 60 – 10 – – – – – 40-50A #8-#6 AWG Cu
1 15 - 30 22 – – – – – – #8-#4 AWG Al
BLHF 55-70A #8-#4 AWG Cu
100 3 15 - 60 – 22 – – – – –
2 15 - 30 10 – – – – – – #8-#2 AWG Al
BGLb 80-100A #4-#1/0 AWG Cu
3 15 - 30 – 10 – – – – –
#2-#1/0 AWG Al
BAF 1 15 - 20 10 – – – – – –
BAFH 1 15 - 20 22 – – – – – –
1 15 - 70 – 22 – – – – –
BLH 2 15 - 100 – 22 – – – – –
3 15 - 100 – – 22 – – – –
1 15 - 70 – 65 – – – – –
HBL 2 15 - 100 – 65 – – – – –
3 15 - 100 – – 65 – – – –
1 – 65 – 14 – – 14 15-40A #14-#6 AWG Cu
2 15 - 100 – 65 – – 14 – 14 #12-#6 AWG Al
BQD
45-100A #8-#1 AWG Cu
3 – – 65 – 14 – 14 #6-#1/0 AWG Al
1 100 – – 25 – – 14 15-30A #14-#6 Cu
2 15 - 125 – 100 100 – 25 – – #12 - #6 Al
125 NGBc
35-125 #6-1/0 Cu
3 – 100 100 – 25 – – #4-2/0 Al

a Main Only
b Two pole breaker is one phase and neutral. Three pole is two phase and neutral.
c P1 panel with NGB branch devices will not accept BL or BQD frames in the same panel as branch devices.
NOTE: BL, HBL, BLH and BQD breakers are mounted in common mountings in 3” or (6) pole increments.
Modifications and Dimensions
Panel Options, Enclosures
• Extra gutter to sides or ends of the can • Painted boxes • Special keyed locks
• 24” wide boxes • Custom colors - TEY
• Hinged trims • Increase gauge trims and boxes - TEU1
• Door-in-door trims • Stainless steel trims and boxes, Type 1 - Cat 60
• Screw to the box trims • Aluminum trims and boxes, Type 1 - LL803
• Trim mounted devices (Devices • NEMA 3R enclosures - LL806
mountedand wired to the trim should • NEMA 3R/12 enclosures - Yale
also have hinged trim specified.) • NEMA 4 enclosures • Meters
- Pilot lights • NEMA 4X enclosures (Contact application engineering
- Toggle switches for space requirements.)
- Push buttons • Panel skirts
• Gaskets between trim and box

Type P1 Dimensions
Type 1 Box (Box is Symmetrical) Type 3R and 3R/12 Box

Flush Mounting

a Dimensions are interior of the box. Add 5/8” to width for absolute dimension.
Add 1/8” to height for absolute dimension. Dimensions shown in inches and millimeters [ ].

The information provided in this flyer contains merely

general descriptions or characteristics of performance
Siemens Industry, Inc. Subject to change without prior notice
which in case of actual use do not always apply as described
Building Technologies Division Order No.: PBSS-20301-0811 or which may change as a result of further development
5400 Triangle Parkway Printed in USA of the products. An obligation to provide the respective
Norcross, GA 30092 © 2011 Siemens Industry, Inc. characteristics shall only exist if expressly agreed in the
terms of contract.
1-800-241-4453
[email protected] All product designations may be trademarks or product
names of Siemens AG or supplier companies whose use by
www.usa.siemens.com/panelboards third parties for their own purposes could violate the rights
of the owners.
 P2 Panelboards
Features
Flexibility is the hallmark of the P2 panel. mixed within unit space by these increments.
This panel offers a wide array of factory- Breakers of the same frame can cross from
assembled options to meet virtually any one mounting to another if contiguous. QJ
lighting panel application. The ability to frame breakers are mounted in 6” increments
mix breaker frames within the unit space for two and three pole, single mounted units.
up to 225 amps will also meet certain Changes in the unit space length for BL, BQD,
distribution panel requirements in a much NGB or ED frame breakers require an addition
smaller package. Bussing options for deadfront, center strip kit. Check with sales or
the P2 vary from a typical temperature the factory for additional unit space kits.
rating of 750 A/Si aluminum, to 1000 A/
Si copper. Standard bussing in the P2 Voltage – 600 Vac max.
panel is tin-plated. Silver-plated copper 250V Vdc max.
is offered as an option. Integrated time Amperage – 600 amp max.
clocks, bus mounted contactors (as mains
or sub mains), split bus, and subfeed lugs Short Circuit Rating – 200 KAIC Max.
(up to 400 amps) are just a few of the symmetrical or equal to the lowest rated
options available in this unique panel. device installed unless a series rating is
indicated. Panels with subfeed or feed-thru
As with our other lighting panelboards, lugs without a main device, circuit breaker or
the standard P2 panel set up includes fusible unit, are limited to a three-cycle rating.
18, 30, 42 or 54 breakers. In specific The three-cycle rating for the P2 panel is
applications, the panel can accept 66, 78 limited to 22 KAIC. Note that the main device
or 90 circuits. The 6” circuit increments may be mounted remote from the panel.
allow the user to configure the smallest
possible panel size. The P2 starts with Bussing – The P2 panel has more options
9” of unit space (18 circuits of 1 pole to meet market requirements. The standard
breakers). Breakers mounted in the unit bussing is temperature rated aluminum. The
space can be mixed and matched to rating is per the requirements of UL 67 –
meet customer requirements. The 1” pole the standard for panelboards. All aluminum
devices (BL, BOD, NGB, ED) are mounted bussing is tin-plated. Optional bussing for the
in 3” or 6” increments. Breaker frames P2 panel is: 750 A/Si aluminum, temperature
above 125A are single mounted in a 6” rated copper, and 1000 A/Si copper. The
space. An example of a minimum panel copper bus option for this panel is tin-plated.
is as follows: (6) 20A, 1-pole, BL breakers Weight – Approximate
(3” of unit space) and a 225A, 3-pole, QJ
breaker (6” of unit space) equaling 9” of Total panelboard weight when filled with a
unit space can be configured in a P2 panel normal quantity of breakers and accessories is
without any extra provisions or space about 3 lbs. (1 kg) per inch
required. FD 250 and JD 400A breakers (54g per mm) of box height.
are mounted outside the unit space.
Table P2-1 – Gauge Steel of Boxes
Another unique feature of the P2 Fronts, Surface and Flush
panel is that blank unit space can be
Dimensions in inches (mm) Gauge Steel
added to allow for future expansion
or modifications. All expansion or Width (in.) Height (in.) Box Front
modifications must be in 3” increments. 20” j 26 - 74 j #16j #14j
BL, BQD, NGB, and ED frame breakers
have 3” or 6” pole kits, and can be (508)j (660, 1880)j

Lighting Panelboards

www.usa.siemens.com/panelboards
Standard Circuit P2 Panels
Base Box Size Requirements for P2 Panels with Standard Line Lugs, and fewer than 55 poles of 1" module (BL,BQD, ED, NGB) branch
breakers and provisions. Unit Spaces range from 9" to 45" (in 6" increments). Boxes range from 26" to 74" high (in 6" increments).
Inclusion of optional modifications may require size increases that must be added to these base values to calculate the final box size for
the panel. Vertical Main breaker options with the “Vert.” designation are added-price options. Values in brackets [ ], at the bottom of
each column, indicate the maximum allowable 1" module branch poles for each main type.
P2 Panels with Standard Line Lugs. Unit Space (starting with 9" and adding 6" increments) “A” Dimension
Main Lugs Main Breakers
“B” Dimen- 125A Horiz. 125A 125A 225A 225A 250A 250A
sion Box 400A BL, BQD, Vert. Horiz. Horiz. Vert. Horiz. Vert. 250A 400A 400A 600A 600A
Height 125A 250A 600A NGB, ED ED  CED QJ QJ FD FD CFD JD CJD LD CLD
26 9 — — 9 — — — — — — — — — — —
32 15 9 — 15 9 9 9 — — — — — — — —
38 21 15 9 21 15 15 15 9 9 — — — — — —
44 27 21 15 27 21 21 21 15 15 9 — — — — —
50 27 27 21 27 27 27 27 21 21 15 9 9 — — —
56 39 27 27 39 33 33 33 27 27 21 15 15 — 9 —
62 45 39 33 45 39 39 39 33 33 27 21 21 9 15 9
68 45 45 39 45 45 45 45 39 39 33 27 27 15 21 15
74 45 45 45 45 45 45 45 45 45 39 33 33 21 27 21
[54p] [54p] [54p] [54p] [54p] [54p] [54p] [54p] [54p] [54p] [54p] [54p] [42p] [54p] [42p]

Extended Circuit P2 Panels

Base box size requirements for Extended Circuit P2 Panels with Standard Line Lugs, and 55 or more poles of 1" module (BL,BQD, ED, NGB)
branch breakers and provisions. Unit Spaces range from 33" to 45" (in 6" increments). Boxes range from 56" to 74" high (in 6" increments).
Inclusion of optional modifications may require size increases that must be added to these base values to calculate the final box size for
the panel (see pages <?>, <?>). Vertical Main breaker options with the “Vert.” designation are added-price options (see page <?>).
Values in brackets [ ], at the bottom of each column, indicate the maximum allowable 1" module branch poles for each main type.
P2 Panels with Standard Line Lugs. Unit Space (starting with 9" and adding 6" increments) “A” Dimension
Main Lugs Main Breakers
“B” Dimen- 125A Horiz. 125A 125A 225A 225A 250A 250A
sion Box 400A BL, BQD, Vert. Horiz. Horiz. Vert. Horiz. Vert. 250A 400A 400A 600A 600A
Height 125A 250A 600A NGB, ED ED CED QJ QJ FD FD CFD JD CJD LD CLD
56 33 — — 33 — — 33 — — — — — — — —
62 39 33 33 39 33 33 39 33 — — — — — — —
68 45 39 39 45 39 39 45 39 33 — — — — — —
74 45 45 45 45 45 45 45 45 39 33 — 33 — — —
[90p] [90p] [90p] [90p] [90p] [90p] [90p] [90p] [78p] [66p] [54p] [66p] [42p] [54p] [42p]
Note: The vertical main breaker application for ED, QJ, and FD adds 6" of box height.

Main breaker wire bending Main lug wire bending

space diagram space diagram

Box depth = 5.75 in. (146 mm) Box depth = 5.75 in. (146 mm)
Box width – 20 in. (508 mm) Box width – 20 in. (508 mm)
for 100-600A for 100-600A
Standard Circuit P2 Panels Extended Circuit P2 Panels
Main Breaker Wire Bending Main Breaker Wire Bending

Standard Circuits (up to 54 1" module branch poles) Extended Circuits (more than 54 1" module branch poles)
Panel Amps Breaker Frames C D Panel Amps Breaker Frames C D
BL 5.75 8.00 BL 5.75 6.56
100 100
BQD 5.13 8.00 BQD 5.13 6.56
NGB 4.63 8.00 NGB 4.63 6.56
125 ED (horiz.) 4.00 8.00 125 ED (horiz.) 4.00 6.56
ED (vert.) 6.56 11.13 ED (vert.) 12.56 14.88
QJ (horiz.) 5.00 7.00 QJ (horiz.) 5.00 6.44
225 225
QJ (vert.) 10.06 16.69 QJ (vert.) 10.06 15.53
FD (horiz.) 5.00 7.00 FD (horiz.) 5.00 5.63
250 250
FD (vert.) 13.25 22.72 FD (vert.) 19.25 25.71
400 JD 15.38 25.00 400 JD 15.38 23.75
600 LD 15.38 23.00 600 LD (54p max) N/A N/A

Main Lug Connectors Main Lug Connectors

Standard Circuits (up to 54 1" module branch poles) Extended Circuits (more than 54 1" module branch poles)
Panel Amps Standard Connectors C D Panel Amps Standard Connectors C D
125 (1) #14-2/0 6.62 8.19 125 (1) #14-2/0 12.62 8.91
250 (1) #6 AWG - 350 MCM 11.75 10.72 250 (1) #6 AWG - 350 MCM 17.75 13.69
(1) #4 AWG - 600 MCM or 14.00 13.09 (1) #4 AWG - 600 MCM or 14.00 14.19
400 400
(2) #6 - 250 MCM (2) #6 - 250 MCM
600 (2) #4 AWG - 500 MCM 14.00 11.00 600 (2) #4 AWG - 500 MCM 14.00 14.23

Branch Breaker Side Gutters Inches (mm)

Reference BL, BLH, HBL BL, BLH, HBL
Letter Panel Width 20" (508) A A
BLF, BLFH BLF, BLFH
A 5.750 (146) BQD, BQD6 BQD, BQD6
B B
B 5.125 (130) ED, ED4, ED6 ED, ED4, ED6
C 4.000 (102) C C
HED4, HHED6 HED4, HHED6
D  5.000 (127) QJ2, QJH2, QJ2-H, HQJ2H
D
E 4.625 (117) (Single Mounted)
E NGB NGB E
Panel Width
20 in. (508 mm)

 Refer to diagrams at the bottom of page 2.

 Single branch mounting construction.
Main Breaker Selection a
Maximum Interrupting Ref.
Ampere Breaker Rating (kA) Catalog
Rating Type 240V 480V 600V Number Available Trip Values
BL 10 — — BL 15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100
HBL 65 — — HB 15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100
BQD 65 14 — BQ 15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100
BLH 22 — — BH 15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100
ED4 65 18 — E4 15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100
100
NGB 100 25 — NB 15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 100
ED6 100 25 14 E6 15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100
HED4 100 42 — H4 15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100
HHED6 100 65 18 HA 15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100
CED6 b 200 200 100 CE 15, 20, 25, 30, 35, 40, 50, 60, 70, 80, 90, 100
NGB 100 25 — NB 110, 125
ED4 65 18 — E4 125

125 ED6 65 25 18 E6 125
HED4 100 42 — H4 125
HHED6 100 65 18 HA 125
CED6 b 200 200 100 CE 125
QJ2 10 — — QJ 60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
QJH2 22 — — QH 60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
QJ2H 42 — — Q2 60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
HQJ2H 100 — — Q3 60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
225 FD6 65 35 18 FD 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
FXD6 65 35 18 FX 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
HFD6 100 65 25 HF 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
HFXD6 100 65 25 H2 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
CFD6 b 200 200 100 CF 70, 80, 90, 100, 110, 125, 150, 175, 200, 225
FD6 65 35 18 FD 250
FXD6 65 35 18 FX 250
250 HFD6 100 65 35 HF 250
HFXD6 65 35 25 H2 250
CFD6 b 200 150 100 CF 50
JXD6b 65 35 25 JX 200, 225, 250, 300, 350, 400
JD6 b 65 35 35 J6 200, 225, 250, 300, 350, 400
HJXD6 100
b 65 35 H6 200, 225, 250, 300, 350, 400
HJD6b 100 65 35 H5 200, 225, 250, 300, 350, 400
400
SJD6 65
b 35 25 SJ 200, 300, 400
SHJD6 100
b 65 35 S2 200, 300, 400
CJD6b 200 200 100 CJ 200, 300, 400
SCJD6 200
b 200 100 SC 200, 300, 400
LXD6b 65 35 25 LX 450, 500, 600
LD6b 65 35 25 L6 250, 300, 350, 400, 450, 500, 600
HLXD6 100
b 65 35 HL 250, 300, 350, 400, 450, 500, 600
HLD6b 100 65 35 HO 250, 300, 350, 400, 450, 500, 600
600
SLD6 65
b 35 25 SL 300, 400, 500, 600
SHLD6 100
b 65 35 S6 300, 400, 500, 600
CLD6b 200 150 100 CL 300, 400, 500, 600
SCLD6 200 150 100 C6 300, 400, 500, 600

When an ED4, ED6, HED4, QJ2, QJH2, QJ2H, FD6, HFD6, or FXD6 frame main breaker, vertically mounted,
is required, price as a main breaker panel and add from the table for the main breaker mounting.

Vertically Mounted Main Breaker

(available in 2-pole or 3-pole)
Ampere Unit Space
Rating Breaker Type(s) (in.)
100 ED4, ED6, HED4 6

QJ2, QJH2, QJ2-H

225 6
FXD6, FD6, HFD6

Subfeed Breakers (available in 2-pole or 3-pole)

Mounting Position When Maximum Interrupting Rating a Interchangeable trip main breakers are mounted at top
Ampere of panel only.
Breaker Used as Subfeed Breaker Ratings (kA) Symmetrical b Vertically mounted.
Type Vertical For Load 240V AC 480V AC 600V AC c Twin
 mounted subfeed breakers are mounted at the
bottom of panelboard only and adds 24" to the panel
FD6 c, FXD6 Twin 70–250 65 35 22 height.
HFD6 c, HFXD6 Twin 70–250 100 65 25 d Subfeed breaker is mounted at bottom of panelboard
only. 400 amp subfeed breaker adds 24" to the panel
JD6 d, JXD6 Single 200–400 65 35 25 height. (Only for use with MLO)
HJD6 d, HJXD6 Single 200–400 100 65 35
 Standard Enclosures Options For Type 1 Trims
Catalog Number Items must be ordered as manual line item
Box
Height Type 1 –Standard Trim on Spartanburg
(in.) Box Surface Flush Type 3R Type 3R/12 Hinged trim – Replace “B” suffix with “H”
26 B26 S26B F26B NR26 WP26 Door-in-door – Replace “B” suffix with “D”
32 B32 S32B F32B NR32 WP32
38 B38 S38B F38B NR38 WP38
Metal card holder – Replace “B” suffix
44 B44 S44B F44B NR44 WP44 with “M” on standard trim, add “M” suffix
50 B50 S50B F50B NR50 WP50 on optional trims
56 B56 S56B F56B NR56 WP56 Option For 24” Wide Enclosures with
62 B62 S62B F62B NR62 WP62 Equal Gutter on Both Sides
68 B68 S68B F68B NR68 WP68 24” wide with equal gutter on both sides,
74 B74 S74B F74B NR74 WP74 add “24” as prefix
Breaker kits and accessories

Kit No. Description Contents

BBKB32 BL/BQD 6-pole 3” branch breaker kit Kit contains top barrier, (3) A/C connectors, (1) B connector, hardware
Kit contains breaker support, interphase barriers (3) A/C connectors,
BBKNB32 NGB 6-pole 3” branch mounting kit
(1) B phase connector, hardware
Kit contains breaker support, inter-phase barriers, (3) A/C connectors,
BBKED32 ED 6-pole 3” branch breaker kit
(1) B connector, hardware
Kit to contain all connectors and cover plates necessary to mount
BBKQ1 QJ branch breaker kit for 2 and 3-pole single mount
both 2 and 3-pole breakers
DFK1 BL, BQD, ED Dead front kit for 1” pole breakers Center strips 3”, 6”, 9,” 15,” 21” plus mounting hardware
DFFP3 Dead front filler 3” 3” empty space filler and hardware
DFFP6 Dead front filler 6” 6” empty space filler and hardware
BNK2 Branch neutral (P2) Three tier lug with mounting hardware to increase neutral capacity
P2BK1 P2 250A max. bonding kit Bonding strap and hardware
P2BK2 P2 400A max. Bonding Kit Bonding strap and hardware
P2BK3 P2 600A max. Bonding Kit Bonding strap and hardware

Branch Circuit Breakers

Maximum Interrupting Rating (kA)
Max. Bolt-On No.
Amp Breaker of Amp Volts – AC DC
Rating Type Poles Rating 120 120/240 240 277 480 600 250 Load Connectors
1 15 - 70 10 – – – – – –
BL 2 15 - 100 – 10 – – – – –
3 15 - 100 – – 10 – – – –
1 15 - 30 10 – – – – – –
BL HID
2 15 - 30 – 10 – – – – –
BLR 2 15 - 100 – – 10 – – – –
1 15 - 30 10 – – – – – – 15-20A #14-#10 AWG Cu
BLE
2 15 - 60 – 10 – – – – – #12-#10 AWG Al
BLEH 1 15 - 30 22 – – – – – –
2 15 - 60 – 22 – – – – – 25-35A #8-#6 AWG Cu
1 15 - 30 10 – – – – – – #8-#6 AWG Al
BLF
2 15 - 60 – 10 – – – – – 40-50A #8-#6 AWG Cu
1 15 - 30 22 – – – – – – #8-#4 AWG Al
BLHF
3 15 - 60 – 22 – – – – –
2 15 - 30 10 – – – – – – 55-70A #8-#4 AWG Cu
BGLa #8-#2 AWG Al
100 3 15 - 30 – 10 – – – – –
BAF 1 15, 20 10 – – – – – – 80-100A #4-#1/0 AWG Cu
BAFH 1 15, 20 22 – – – – – – #2-#1/0 AWG Al
1 15 - 70 – 22 – – – – –
BLH 2 15 - 100 – 22 – – – – –
3 15 - 100 – – 22 – – – –
1 15 - 70 – 65 – – – – –
HBL 2 15 - 100 – 65 – – – – –
3 15 - 100 – – 65 – – – –
1 – 65 – 14 – – 14 15-40A #14-#6 AWG Cu
2 15 - 100 – 65 – – 14 – 14 #12-#6 AWG Al
BQD 3 – – 65 – 14b – 14 45-100A #8-#1 AWG Cu
#6-#1/0 AWG Al
1 100 – – 25 – – 14 15-30A #14-#6 Cu or #12 - #6 Al
NGB 2 15 - 125 – 100 100 – 25 – –
3 – 100 100 – 25b – – 35-125A #6-1/0 Cu or #4-2/0 Al
ED2 1 15 - 125 10 – – – – – –
2, 3
1 15 - 125 65 – – 22 – – – 15-25A #14-#10 AWG Cu
ED4 2 – – 65 – 18 – 30 #12-#10 AWG Al
125 3 – – 65 – 18 – – 30-100A #10-#1/0 Cu or Al
ED6 2 15 - 125 – – 65 – 25 18 30
3 – – 65 – 25 18 – 100-125A #3-3/0 Cu
HED4 1 100 – – – – – – #1-2/0 Al
2 15 - 125 – – – 65 – – –
HHED6 3 – – 100 42 42 – 30
QJ2 2&3 60 - 225 – – 10 – – – –
QJH2 2&3 60 - 225 – – 22 – – – – 60-225A #6 AWG-300 Kcmil Cu
225
QJ2-H 2&3 60 - 225 – – 42 – – – – #4 AWG-300 Kcmil Al
HQJ2H 2&3 100 - 225 – – 100 – – – –
NOTE: QJ Breakers are single mounted in nit space and take 6” of unit space. Limited to (3) per panel max. BL, HBL, HBL and BQD breakers are mounted in common
mountings in 3” or (6) pole increments. ED2, ED4, ED6, HED4 and HHED6 breakers are mounted in common mountings in 3” or (6) pole increments. NGB breakers
are mounted in common mounting in 3” or (6) pole increments.
a Two pole breaker is one phase and neutral. Three pole is two phase and neutral. b For use on 480Y/277 volt systems not suitable for 480 delta 3 phase 3 wire systems.
Box Size Additions for Optional Features
Main Lugs Main Breakers
125A
250A
400A 600A 125A 125A 125A 225A 225A 225A 250A 250A 400A 400A 600A 600A
Options Horiz. Horiz. Vert. Horiz. Vert. Horiz. Vert. Vert. JD CJD LD CLD
BL, BQD,
ED, NGB CED ED QJ QJ FD FD CFD
*Min. Box Size 26" 32" 38" 38" 26" 32" 32" 32" 38" 38" 44" 50" 50" 62" 56" 62"
200% Neutral 0 0 6 (all) 6 (all) 0 0 0 N/A 0 N/A 0 0 0 0 0 0
(lug type)
Std. Lugs 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
(100% Neut. PNL)
CU Lugs (100% 6 6 6 0 N/A N/A 0 N/A 0 N/A 0 0 0 0 0 0
Neut. PNL)
Comp Lugs 6 6 6 6 N/A N/A 0 N/A 0 N/A 0 0 0 0 0 0
(100% Neut. PNL)
Feed-thru
Standard Lugs 6 6 12 12 6 6 6 N/A 6 N/A 6 6 12 12 12 12
Feed-thru Cu Lugs 6 6 12 N/A N/A N/A 6 N/A 6 N/A 6 6 12 12 N/A N/A
Feed-thru
Comp Lugs 6 12 12 N/A N/A N/A 6 N/A 6 N/A 12 12 12 12 N/A N/A
Subfeed Standard
Lugs 0 6 6 N/A — — — — — — — — N/A — — —
Split Bus 6 6 6 6 6 6 6 N/A 6 N/A 6 6 6 6 6 6
(1) FD Subfeed N/A 12 12 12 N/A N/A N/A N/A N/A 12 12 12 12 12 12 12
(Horizontal Mtg.)
(2) FD Subfeed N/A 24 24 24 N/A N/A N/A N/A N/A 24 24 24 24 N/A N/A N/A
(Vertical Mtg.)
SPD 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

Split

bus is paired with feed-thru lugs by default. Feed-thru lugs are to feed the section after the split.
NOTE: N/A = OPTION NOT AVAILABLE
*Min. Box Size, corresponding to 9" of Unit Space.

Compression Lugs
Amp Breaker Compression Box Height
Style Rating Type Connectors Addition
125 N/A (1)#6 - 350 kcmil Al/Cu 6
250 N/A (1)#6 - 350 kcmil Al/Cu 6
MLO (1) 400 - 600 kcmil Cu or
400 N/A 6
(2)#6 - 350 kcmil Al/Cu
(2)#6 - 350 kcmil Cu or Cu/Al or
600 N/A 6
400 - 600 kcmil Al/Cu
Box must go to 24" wide on CED6 breaker
ED4, ED6, HED4
100 (1)#14-2/0 AWG Cu or Al only
HHED6, CED6
Add 6" to box height for NØ
225 QJ2, QJH2, QJ2H (1)#6 AWG - 350 kcmil Cu or Al Box must go to 24" wide
Box must go to 24" wide for all breakers
250 FXD6, HFD6, CFD6 (1)#6 AWG - 350 kcmil Cu or Al
Main Requires an additional 6.0" box height
Breaker JD6, JXD6, HJD6,
400 CJD6, SJD6, SHJD6, (2)#1/0 AWG - 500 kcmil Cu or Al 9
SCJD6
LD6, LXD6, HLD6,
600 CJD6, SLD6, SHLD6, (2)#2/0 AWG - 500 kcmil Cu or Al 6
SCLD6

Alternate Lugs
Amp Breaker Standard AL Box Height
Style Rating Type Connectors Addition
(1) 250 - 750 kcmil or
MLO 400 N/A 6
(2)#3/0 AWG - 250 kcmil Cu or Al
JD6, JXD6, HJD6,
Main
400 CJD6, SJD6, SHJD6, (1)#4/0 AWG - 750 kcmil Cu or Al 6
Breaker
SCJD6

 Not availabe for feed thru lug.

Modifications and Dimensions
Panel Options, Enclosures
• Extra gutter to sides or ends of the can • Painted boxes • Special keyed locks
• 24” wide boxes • Custom colors - TEY
• Hinged trims • Increase gauge trims and boxes - TEU1
• Door-in-door trims • Stainless steel trims and boxes, Type 1 - Cat 60
• Screw to the box trims • Aluminum trims and boxes, Type 1 - LL803
• Trim mounted devices (Devices • NEMA 3R enclosures - LL806
mountedand wired to the trim should • NEMA 3R/12 enclosures - Yale
also have hinged trim specified.) • NEMA 4 enclosures • Meters
- Pilot lights • NEMA 4X enclosures (Contact application engineering
- Toggle switches for space requirements.)
- Push buttons • Panel skirts
• Gaskets between trim and box

Type P2 Dimensions
Type 1 Box (Box is Symmetrical) Type 3R and 3R/12 Box

Flush Mounting

a Dimensions are interior of the box. Add 5/8” to width for absolute dimension.
Add 1/8” to height for absolute dimension. Dimensions shown in inches and millimeters [ ].
 The information provided in this flyer contains merely
general descriptions or characteristics of performance
Siemens Industry, Inc. Subject to change without prior notice
which in case of actual use do not always apply as described
5400 Triangle Parkway Order No.: PBSS-20302-0811 or which may change as a result of further development
Norcross, GA 30092 Printed in USA of the products. An obligation to provide the respective
© 2011 Siemens Industry, Inc. characteristics shall only exist if expressly agreed in the
1-800-241-4453 terms of contract.
[email protected]
All product designations may be trademarks or product
names of Siemens AG or supplier companies whose use by
www.usa.siemens.com/panelboards third parties for their own purposes could violate the rights
of the owners.
 P3 Panelboards
Features
The innovative P3 panelboard from are mounted in 6” increments for two and
Siemens is a smaller footprint distribution three pole single and twin mounted units.
panel designed for applications that Changes in the unit space length for Bl,
require more large-branch devices than BQD, NGB, NEB, HEB, and ED frame breakers
typical lighting panels can support. This require an additional deadfront center strip
panel offers a wide array of factory- kit. Contact your Siemens representative for
assembled options and has the ability additional unit space kits.
to mix breaker frames in unit space up
to 225 amps. Bussing options include Voltage – 600 Vac max.
standard, temperaturerated aluminum 250V Vdc max.
and temperature rated (750 ASI1 and Amperage – 600 amp max.
1,000 AlSq”) copper. All aluminum
bussing in the P3 panel is tin-plated as Short Circuit Rating – 200 KAIC Max.
a standard. Silver-plating is the default symmetrical or equal to the lowest rated
for copper bus with tin as an option. device installed unless a series rating is
Integrated time clocks, bus mounted indicated. Panels with subfeed or feed-thru
contactors as mains or sub-mains, split lugs without a main device, circuit breaker or
bus and sub-feed lugs (up to 400 amps) fusible unit, are limited to a three-cycle rating.
are just a few of the options available in The three-cycle rating for the P3 panel is
this unique panel. limited to 22 KAIC. Note that the main device
may be mounted remote from the panel.
The panel configurations, defined by unit
space, allow for given amperage, main Bussing – The P3 panel has more options
device, and box height. The P3 panel to meet market requirements. The standard
starts with a 56” high box. Breakers in bussing is temperature rated aluminum. The
unit space can be mixed and matched to rating is per the requirements of UL 67 –
meet customer requirements. All 1”pole the standard for panelboards. All aluminum
breakers (Bl, BOD, NGB, NEB, HEB and bussing is tin-plated. Optional bussing for the
ED frames) are mounted in 3” or 6-pole P3 panel is: 750 A/si aluminum, temperature
increments. Breaker frames, rated 225 rated copper, and 1000 A/si copper. The
amps, are dual mounted in 6” increments copper bus option for this panel is tin-plated.
in unit space. Also available are one or Weight – Approximate
two 250 amp frame breakers or one 400
amp frame breaker, mounted as sub-feed Total panelboard weight when filled with a
devices outside the unit space. normal quantity of breakers and accessories is
about 5 lbs. (1 kg) per inch (54g per mm) of
Like other distribution panels, the box height.
P3 panel can include blank space for
future expansion or modifications. Any Table P3-1 – Gauge Steel of Boxes Fronts,
expansions or modifications must be in Surface & Flush
3”increments. BL, BQD, NGB, NEB, HEB,
Dimensions in inches (mm) Gauge Steel
and ED frame breakers have 3” or 6-pole
kits and can be mixed in unit space by Width (in.) Height (in.) Box Front
these increments. Breakers of the same 24” j 56 - 80 j #16j #14j
frame can cross from one mounting to
another if contiguous. QJ frame breakers (610)j (1422, 2032)j
1 ASI = Amperes per square inch

Lighting Panelboards

www.usa.siemens.com/panelboards
Panel Unit Space To Box Height Requirements
P3 Panels With Standard Line Lugs. Unit Space (starting with 9” and adding 6” increments) “A” Dimension
Main Lugs Main Breakers
“B” 250A 400A 600A 800A 250A 250A 250A 400A 400A 600A 600A
Dimension Horiz. Vert.
Box Height FD FD CFD JD CJD LD CLD
56 27 21 21 21 21 15 9 9 — 9 —
62 33 27 27 27 27 21 15 15 9 15 9
68 39 33 33 33 33 27 21 21 15 21 15
74 45 39 39 39 39 33 27 27 21 27 21
80 51 45 45 45 45 39 33 33 27 33 27

Main Breaker Selection1

“B” Maximum interrupting rating (kA)
Box Height P3 Panels Wit 240V 480V 600V Lug wire range
FD6, FXD6 (STD) 65 35 18 #6 AWG - 350 Kcmil Cu
250 HFD6, HFXD6 100 65 25 or
CFD6 200 150 100 #4 AWG - 30 Kcmil Al
JXD6 (STD), JD6 65 35 25
3/0 - 500 Kcmil Cu
HJD6, HJXD6 100 65 35
400 or
SJD6 65 35 25
4/0 - 500 Kcmil Al
CJD6, SCJD6 200 200 100
LXD6 (STD) 65 35 25
LD6 65 35 25
3/0 - 500 Kcmil Cu
HLD6, HLXD6 100 65 35
600 or
SLD6 65 35 25
4/0 - 500 Kcmil Al
SHLD6 100 65 35
CLD6, SCLD6 200 150 100

Fig. P3-1 Table P3-1 – Gauge Steel of Boxes Fronts, Surface & Flush
Dimensions in inches (mm) Gauge Steel
Width Height Box Front
24” 56 - 80 #16 #14
-610 (1422, 2032)

Typical Panelboard Wiring Diagrams

Main Breaker Main Lugs Main Breaker Main Lugs

Box depth = 7.75 in. (197 mm)

Box width = 24 in. (610 mm) 1 Phase, 3 Wire 3 Phase, 4 Wire,
3 Phase 3 Wire (No SN)
Branch Breaker Side Gutters Inches (mm) (Fig. P3-2) Fig. P3-2
Reference Panel Width
Letter 24” (609) BL, BLH, HBL BL, BLH, HBL
A A
BLF, BLFH BLF, BLFH
A 7.750 (197)
B BQD, BQD6 BQD, BQD6 B
B 7.125 (181)
C NGB NGB C
C 6.620 (168) D NEB, HEB NEB, HEB D
D 6.440 (164) ED, ED4, ED6 ED, ED4, ED6
E E
E 6.000 (152) HED4, HHED6 HED4, HHED6
F QJ2, QJH2, QJ2-H, HQJ2H QJ2, QJH2, QJ2-H, HQJ2H F
F 7.000 (178)
Panel Width
24 in. (610 mm)

Branch Breaker Side Gutters Inches (mm) (Fig. P3-2)

Catalog Number Options For Type 1 Trims
Box Type 1 Items must be ordered as manual line item on factory.
Height Standard Trim Hinged trim – Add “H” suffix
(In.) Box Surface Flush Type 3R Type 3R/12 Door-in-door – Add “D” suffix
56 24WD56 P3S56 P3F56 24NRD56 24WPD56 Metal card holder – Add “M” suffix
62 24WD62 P3S62 P3F62 24NRD62 24WPD62
68 24WD68 P3S68 P3F68 24NRD68 24WPD68
74 24WD74 P3S74 P3F74 24NRD74 24WPD74
80 24WD80 P3S80 P3F80 24NRD80 24WPD80
1Interchangeable trip main breakers are mounted at top of panel only.
Breaker kits and accessories

Kit No. Description Contents

BBKB32 BL/BQD 6-pole 3” branch breaker kit Kit contains top barrier, (3) A/C connectors, (1) B connector, hardware
Kit contains breaker support, interphase barriers (3) A/C connectors,
BBKNB32 NGB 6-pole 3 branch mounting kit
(1) B phase connector, hardware
Kit contains breaker support, interphase barriers (3) A/C connectors,
BBKEB32 NEB/HEB 6 pole 3 branch breaker kit
(1) B phase connector, hardware
Kit contains breaker support, inter-phase barriers, (3) A/C connectors,
BBKED32 ED 6-pole 3” branch breaker kit
(1) B connector, hardware
Kit to contain all connectors and cover plates necessary to mount
BBKQ1 QJ branch breaker kit for 2 and 3-pole single mount
both 2 and 3-pole breakers
Kit to contain all connectors and cover plates necessary to mount
BBKQ2 Branch breaker kit for 2 and 3-pole QJ twin mount
both 2 and 3-pole breakers
DFFP3 Deadfront filler 3” 3” empty space filler and hardware
DFFP6 Deadfront filler 6” 6” empty space filler and hardware
P3BK1 P3 bonding kit Bonding strap and hardware
Filler plate for BL, BQD, ED frame
QF3 1” filler plate
branch breaker provisions
EBF1 Filler plate for NEB/HEB branch breaker provision content 1” filler plate
Branch Circuit Breakers
Maximum Interrupting Rating (kA)
Max. Bolt-On No.
Amp Breaker of Amp Volts – AC DC
Rating Type Poles Rating 120 120/240 240 277 480 600 250 Load Connectors
1 15 - 70 10 – – – – – –
BL 1 2 15 - 100 – 10 – – – – –
3 15 - 100 – – 10 – – – –
1 15 - 30 10 – – – – – –
BL HID
2 15 - 30 – 10 – – – – –
BLR 2 15 - 100 – – 10 – – – –
1 15 - 30 10 – – – – – –
BLE 15-20A #14-#10 AWG Cu
2 15 - 60 – 10 – – – – –
1 15 - 30 22 – – – – – – #12-#10 AWG Al
BLEH 25-35A #8-#6 AWG Cu
2 15 - 60 – 22 – – – – –
1 15 - 30 10 – – – – – – #8-#6 AWG Al
BLF
2 15 - 60 – 10 – – – – – 40-50A #8-#6 AWG Cu
1 15 - 30 22 – – – – – – #8-#4 AWG Al
BLHF
3 15 - 60 – 22 – – – – – 55-70A #8-#4 AWG Cu
100
2 15 - 30 10 – – – – – – #8-#2 AWG Al
BGL
3 15 - 30 – 10 – – – – – 80-100A #4-#1/0 AWG Cu
BAF 1 15, 20 10 – – – – – – #2-#1/0 AWG Al
BAFH 1 15, 20 22 – – – – – –
1 15 - 70 – 22 – – – – –
BLH 1 2 15 - 100 – 22 – – – – –
3 15 - 100 – – 22 – – – –
1 15 - 70 – 65 – – – – –
HBL 1 2 15 - 100 – 65 – – – – –
3 15 - 100 – – 65 – – – –
1 – 65 – 14 – – 14 15-40A #14-#6 AWG Cu
2 15 - 100 – 65 – – 14 – 14 #12-#6 AWG Al
BQD 1, 3
3 – – 65 – 14 – 14 45-100A #8-#1 AWG Cu
#6-#1/0 AWG Al
1 100 – – 25 – – 14 15-30A #14-#6 Cu
NGB 2, 3 2 15 - 125 – 100 100 – 25 – – #12 - #6 Al
35-125A #6-1/0 Cu
3 – 100 100 – 25 – – #4-2/0 Al
1 85 – – 35 – – – 15-100 A #14-1/0 Al/Cu
NEB 3, 4 2 15 - 125 – 85 85 – 35 – –
3 – 85 85 – 35 – – 110-125A #6 - 3/0 Al/Cu
1 100 – – 65 – – – 15-100A #14-1/0 Al/Cu
HEB 3, 4 2 15 - 125 – 100 100 – 65 – –
125 3 – 100 100 – 65 – – 110-125A #6 - 3/0 Al/Cu
1 15 - 125 65 – – 22 – – –
ED4 5 2 – – 65 – 18 – 30 15-25A #14-#10 AWG Cu
3 – – 65 – 18 – – #12-#10 AWG Al
2 15 - 125 – – 65 – 25 18 30
ED6 5 30-100A #10-#1/0 Cu or Al
3 – – 65 – 25 18 –
1 100 – – – – – – 100-125A #3-3/0 Cu
HED4 5
2 15 - 125 – – – 65 – – – #1-2/0 Al
HHED6 5
3 – – 100 42 42 – 30
QJ2 6 2&3 60 - 225 – – 10 – – – –
QJH2 6 2&3 60 - 225 – – 22 – – – – 60-225A #6 AWG-300 Kcmil Cu
225
QJ2-H 6 2&3 60 - 225 – – 42 – – – – #4 AWG-300 Kcmil Al
HQJ2H 6 2&3 100 - 225 – – 100 – – – –
1 BL, HBL, BLH and BQD breakers are mounted in common mountings in 3” or 6 4 NEB/HE breakers are counted in common mountings of 3” or 6 pole increments.
pole increments. 5 ED4, ED6, HED4 and HHED6 breakers are mounted in common mountings in 3”
2
 NGB breakers are counted in common mountings of 3” or 6 pole increments. or (6) pole increments.
3 For use on 480Y/277 volt systems. Not suitable for 480 Delta 3 phase 3 6 QJ Breakers are single mounted in unit space and take 6” of unit space.

wire systems. Limited to (3) per panel max.

Modifications and Dimensions
Panel Options, Enclosures
• Extra gutter to sides or ends of the can • Painted boxes • Special keyed locks
• 24” wide boxes • Custom colors - TEY
• Hinged trims • Increase gauge trims and boxes - TEU1
• Door-in-door trims • Stainless steel trims and boxes, Type 1 - Cat 60
• Screw to the box trims • Aluminum trims and boxes, Type 1 - LL803
• Trim mounted devices (Devices • NEMA 3R enclosures - LL806
mountedand wired to the trim should • NEMA 3R/12 enclosures - Yale
also have hinged trim specified.) • NEMA 4 enclosures • Meters
- Pilot lights • NEMA 4X enclosures (Contact application engineering
- Toggle switches for space requirements.)
- Push buttons • Panel skirts
• Gaskets between trim and box

Type P3 Dimensions
Type 1 Box (Box is Symmetrical) Type 3R and 3R/12 Box

Flush Mounting

a Dimensions are interior of the box. Add 5/8” to width for absolute dimension.
Add 1/8” to height for absolute dimension. Dimensions shown in inches and millimeters [ ].

The information provided in this flyer contains merely

general descriptions or characteristics of performance
Siemens Industry, Inc. Subject to change without prior notice
which in case of actual use do not always apply as described
5400 Triangle Parkway Order No.: PBSS-20303-0811 or which may change as a result of further development
Norcross, GA 30092 Printed in USA of the products. An obligation to provide the respective
© 2011 Siemens Industry, Inc. characteristics shall only exist if expressly agreed in the
1-800-241-4453 terms of contract.
[email protected]
All product designations may be trademarks or product
names of Siemens AG or supplier companies whose use by
www.usa.siemens.com/panelboards third parties for their own purposes could violate the rights
of the owners.