0% found this document useful (0 votes)
187 views11 pages

HF Static Transceivers As Per MHA QR (Version 2.0)

This document outlines the technical specifications for a Static HF Transceiver, including: 1. The transceiver will operate in the 2-30 MHz frequency range with 10 Hz channel spacing and support SSB, AM, CW modes. 2. It will have over 100 preset channels, less than 1 ppm frequency stability, 50 ohm antenna impedance, and EMI/EMC compliance. 3. Transmitter specifications include 20-100W output power, sideband suppression over 50dB, carrier suppression over 40dB, and intermodulation distortion over 30dB below peak envelope power.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
187 views11 pages

HF Static Transceivers As Per MHA QR (Version 2.0)

This document outlines the technical specifications for a Static HF Transceiver, including: 1. The transceiver will operate in the 2-30 MHz frequency range with 10 Hz channel spacing and support SSB, AM, CW modes. 2. It will have over 100 preset channels, less than 1 ppm frequency stability, 50 ohm antenna impedance, and EMI/EMC compliance. 3. Transmitter specifications include 20-100W output power, sideband suppression over 50dB, carrier suppression over 40dB, and intermodulation distortion over 30dB below peak envelope power.
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

GOVERNMENT OF INDIA

(Ministry of Home Affairs)


.DIRECTORATE GENERAL
CENTRAL RESERVE POLICE FORCE
EAST BLOCK.T sEc-l R.K. PURAM NEW DELHI.I10066
(Email:- [email protected] Tele/Fa>r:Ol l-26109038)

No. B.V-7 l2o2t-22-C (QRs) Dated, the yFebruary'2O22

To

1. DIG (Comn), ITBP 2. DIG (Comn), NSG


Block No. 2, CGO Complex Meharam Nagar
Lodhi Road, New Delhi-O3 Palam, New Delhi-37

3. DIG (Comn), SSB 4. AIG (Comn), CISF


East Block-V, R.K Puram Block No. 13, CGO, Complex
New- Delhi-66 Lodhi Road, New Delhi-O3

5. DIG (Prov), BSF 6. Liaison Office, Assam Rifle


Block No. 10, CGO Complex Room No-171, North Block, MHA
Lodhi Road, New Delhi-O3 New Delhi -01

Subject: ReEardlng revision of ORs/TDs of gStatic HF Transcelver".

Please find enclosed QRs/TDs of "Static HF Transceiver" as Annexure-


"A" duly approved by the competent authority is forwarded herewith for further
necessary action.
ii) Further QRs/TDs of "Static HF Transceiver" approved on L2IO9/2OL9
will be obsolAte and dropped.

Encl: (Approved QRs & TDs of "Static HF Transceive/)

a.1-
{Sunil Kr (Comn))
For DIG (Equipment)
Directorate General, CRPF
t

ORs OF STATIC HF TRANSCEIVER

'P' 1 General Specillcation

s.N Parameter Specificatlons


1 Frequency Range 2.O MHz to 29.9999 MHz channel spacing 10
Hz.
2 Modes ssB( J3E) USB, LSB, AM, CW/MCW
3 Preset 100 Channels or more
4 Frequency tl PPM or better
Stability
5 Built-in-test Front panel testing.
6 Input Power +l2V or 24Y * LOo/o DC Nominal & 230V * IOo/o
AC
7 Power s4OW in Receive & < 450W in Transmit
Consumption
8 EMI / EMC MIL-STD- 4611462C or ETSI or CISPR 22 or
IEC 61000-4 Series (TEC/EMI/TEL-001/01
FEB-09) or better standard
9 Weight Less than 20 KG
10. Antenna 50 C) Unbalanced
Impedance
l1 Protection (i) Reverse Polarity protection
(without fuse )
(iil Protection against high VSWR. Radio set
should be protected from 3.5:l or above VSWR.
(iii) Over Voltage and under Voltage Protection.
12 Roles Fixed / Transportable / Mobile
13. Headphone Up to 600C)
Impedance
74. Cooling Built in fan/ Heat sink
15 VSWR Better than 1.5
16. Visual display Front panel LCD/LED display or latesl.
technolory
17. Interface RS-232 / USB
18. Programming PC programming software and front panel
programming.

--;f-!rll'( -2, \-.


4y@urv
+^e \
I
-2-

s.N Parameter Speclfications


r,'
I
t.2 Transmitter Specification
1 RF Power 20W to 100W PEP (Low, Medium , High)
As per user requirement with
programmable feature.
2 Spurious Emission > 46 dB below PEP
Suppression
3 Side Band > 50 dB or better
Suppression
4 Carrier Suppression > 40 dB or better
5 Inter modulation 30 dB minimum below PEP
distortion
6 Audio Response Within 6 dB from 350H2 to 27OOHz
7 Side Tone l,evel Better than 0.1 mW into 150Cl load for
5mV of audio iirput at 1 KHz.
8 Modulation Sensitivity 1 to lO mV at l KHz for full power under
SSB mode.
1.3 Receiver Specification
1 Receiver Sensitivity -LO7 dBm for 10dB SINAD or better
2 Image Rejection >70 dB or better
3 IF Rejection >70 dB or better
4 In band Inter 35 dB minimum below PEP
Modulation
Distortion
5 Audio Response Within *6 dB from 350H2 to 27OOHz
6 Audio Output lW or more across loudspeaker
7 Audio Frequency > 25 dB or better
Harmonics
Distortion.
1.4 Euvironmental Parameters
1 Operating -30'C to +55" C
Temperature
2 Storage Temperature -30"C to +60'C
3 Humidity 9 5o/o non- condens ing @ 40' C.
4 Dust MIL-STD-8lOF or better
5 Vibration or
6. Shock JSS-55555 (As laid down in Class L3 of
7 Water Intrusion JSS-55555, revision No.2)
8 Altitude

t--
/z-
1
u \/

A \ I

.t.'-',
v -3-

s.N Parameter Specifications


v
J

1.5 f,'eatures
1 Selective calling Digital FSK coding
2 Scanning 5 channels per second or better
3 Flash messages Minimum 60 characters
4 Vocoder MELP/CELP (1200 l2a0obps) or better
5 In built Data Modem MrL-STD -188 -rtOA/BlC single tone up to
4800 bps or more.
6 Data Communication Provision for data communication
7 Tele Call The Radio set should have capability to dial
and operate data.
8 RS-232 control The Radio set should have capability to
operate at 4800 baud rate or better
9 Tuneable receiver Continuous tuneable.
10. Radio kill/un-kill be able to manually erase the
data.
11. Remote Operation Capable to operate from remote location
through cable.
L2 Audio input sockets Mic and external socket.
13. Squelch Voice/Digital squelch
14. Push to talk Suitable Microphone to be provided.
1.6 Optional Features
user
1 Communication AES 128 bit or AES 256 bit or SAG approved
Security (As per user requirement)
2 ALE 2G I ALE 3G ALE 2G as per Appendix "A" and ALE 3G as
per Appendix "C" of MIL-STD- 188- 14 1B
3 Frequency Hopping Hop Rate: >6 hops per second
4 GPS Interface Inbuilt GPS with polling facility
b Data Terminal Specifications:
Should also be com tible with existing HF Radio
a) Processor Intel Core i5 9ot generation/equivalent o
better
b) Speed 2.5 GHz or better
c) RAM Minimum 8GB DDR4 (Expendable up to 64
GB or better)
d) Memory Speed 2133 MHz or better
e) Storage 2s6 GB or more plP
<<-.-D'ltt'l (^ 4/
a{fliuu
\
L-
c -4-

a s.N Parameter Speciflcations


0 Display Size 14 Inch or more
s) Interface USB, HDMI /DP Port
h) Keyboard Multimedia/ Membrane
i) Mouse Touchpad
i) Operating System Windowsl0 or latest Windows version OS
k) Battery endurance 18 hrs or more with one battery
U Data communication Compatible with Windows 10 or latest
software version Windows OS
m) Operating Temperature -10"C to +50" C
n) Storage Temperature -2O"C to +60"C
o) Dust and water IP 53 or better
resistance test
p) Safety Standards MIL-STD-8IOH or better or JS-55555 or
better
q) Drop resistance test 90 cm

(SI/RM. Ashok Kumar Rajwant) (WO/RM. Jaydeep Verma)


BSF Assam Rifles
/")
Singh, AC)
ITBP
( h^.
SSB

rrry
(H Dy.Dir) (Viplav Azad, DC) (Maj.Ajay Antil) (Sunil I(r Singh), DC(Comn)
DCPW CISF NSG CRPF

L
{ I
(Amit , DIG(Eqpt) Agrawal),DIG(Comn)
CRPF CRPF
,u)
€r
(Syed Mohd Husnain)
IG(Comn&IT), CRPF
(Zulfiquar Hasan),IPS
SDG(OPS),CRPF

o
Singh, rPS)
DG, CRPF
(
QRS/TDS OT. STATIC HF TRANSCETVER
lr5 1.1 General Specification
'-.-'
s.N Parameter Specifications Trlal Directives
1 Frequency 2.O MHz to 29.9999 BOO will check frequencY
Range MHz channel spacing range of I.IF set bY
IO Hz. programming lowest, highest
and any random frequencY in
2.0-29.9999 MHz range and
will measure with the helP of
standard testing instruments.
The RF output and sensitivitY
of radio set in entire band
should be same.
2 Modes ssB( J3E) USB, LSB, BOO will check Modulation
AM, CW/MCW practically after switching "ON"
the radio set and setting these
modes one by one and firm will
produce OEM certificate.
3 Preset 100 Channels or more BOO will check it practicallY
by setting the channels in the
radio set.
4 Frequency t1 PPM or better BOO will check Parameter
Stability practically by using the
standard test instrument.
5 Built-in-test Front panel testing. BOO will check practicallY.
6 Input Power +l2Y or 24Y t 10% DC BOO will check practicallY bY
Nominal&230VtlOo/o connecting mentioned DC/AC
AC voltages to radio set and will
ensure that set works ProPerlY.
7 Power BOO will check practicallY
Consumption 450W in Transmit
8 EMI / EMC MIL-STD - 461 1462C ot The firm will produce
ETSI or CISPR 22 or certificate of Govt Lab. or
IEC 61000-4 Series NABL/ILAC accredited
(TEC/EMI/rEL-00 t lot laboratory.
FEB-09) or better
standard
.l uqi'

\- \
/*
r.

-2-
!
-t.

s.N Parameter Speclflcatlons Trial Directives


9 Weight Less than 20 KG BOO will measure weight
with help of weighing
machine.
10. Antenna 50 C) Unbalanced BOO will check practically.
Impedance
11. Protection (i) Reverse Polarity BOO will check practicallY
protection and firm will produce OEM
(without fuse ) certificate.
(ii) Protection against high
VSWR. Radio set should be
protected from 3.5:1 or
above VSWR.
(iii) Over Voltage and under
Voltage Protection.
t2 Roles BOO will check practicallY'
F ixed / Transportable / Mobile

13 Headphone Up to 600C) BOO will check


Impedance practically/Firm will Produce
OEM certificate.
t4. Cooling Built in fan/ Heat sink BOO will check Physically.
15. VSWR Better than 1.5 BOO will check PracticallY.
16. Visual Front panel LCD/LED BOO will check practicallY.
display display or latest technolory
t7. lnterface RS-232 / USB BOO will check practicallY.
18 Programming PC programming software BOO will check practicallY bY
and front panel software and front Panel
programming. programming.
1.2 Transmitter Specification
1 RF Power 2OW to 1O0W PEP (Low, BOO will check practicallY.
Medium , High)
As per user requirement
with programmable feature.
2 Spurious > 46 dB below PEP BOO will check practicallY.
Emission
Suppression
3 Side Band > 50 dB or better BOO will check practicallY.
Suppression
+

quL

L
\
a
-3-
a
f, s.N Parameter Speclfications Trial Dlrectives
4 Carrier > 40 dB or better BOO will check
Suppression practically.
5 Inter modulation 30 dB minimum below PEP BOO will check
distortion practically.
6. Audio Response Within 6 dB from 350H2 to BOO will check
27OOHz. practically.
7 Side Tone Level Better than 0.1 mW into BOO will check
150C) load for SmV of audio practically.
input at I KHz.
8 Modulation 1 to 10 mV at I KHz for full BOO will check
Sensitivity power under SSB mode. practically.
1.3 Receiver Specification
1 Receiver -lOT dBm for lOdB SINAD or BOO will check
Sensitivity better practically.
2 Image Rejection >70 dB or better BOO will check
practically.
3 IF Rejection >70 dB or better BOO will check
practically.
4 In band Inter 35 dB minimum below PEP Firm will produce OEM
Modulation certificate.
Distortion
5 Audio Response Within t6 dB from 350H2 to BOO will check
27OOHz practically.
6 Audio Output lW or more across BOO will check
loudspeaker practically.
7 Audio > 25 dB or better BOO will check
Frequency practically.
Harmonics
Distortion.
t,4 Euvironmental Parameters
1 Operating -3O'C to +55" C The firm will produce
Temperature certificate of Govt. Lab.
2 Storage -3O"C to +60"C or NABL/ILAC
accredited laboratory.
Temperature I

0 (<."rJrA
-@ .C\
a/
\-"
-a{5xt''

,L v \ I
a,

-4-
t
a-

s.N Parameter Specifications Trial Dlrectives


3 Humidity non-condensing @ 40'C
9 5%o The firm will produce
4 Dust MIL-STD-810F or better certilicate of Govt. Lab.
5 Vibration or or NABL/ ILAC
6. Shock JSS-55555 (As laid down in accredited laboratory.
7 Water Intrusion Class L3 of JSS-55555,
revision No.2)
8 Altitude
1.5 Features
1 Selective calling Digital FSK coding Firm will produce OEM
2 Scanning 5 channels per second or Certificate.
better
3 Flash messages Minimum 60 characters BOO will check
practically.
4 Vocoder MELP/ CELP ( 1 200/ 2a00bps) Firm will produce OEM
or better certificate.
5 In built Data MrL-STD - 188 -tLOAlH- lC Firm will produce OEM
Modem single tone up to 4800 bps or certificate.
more.
6 Data Provision for data BOO will check
Communication communication practically.
7 Tele Call The Radio set should have Firm will produce OEM
capability to dial and operate certificate.
data.
8 RS-232 control The Radio set should have BOO will check
capability to operate at 4800 practically.
baud rate or better.
9 T\rneable receiver Continuous tuneable. BOO will check
practically.
10. Radio kill/un-kill Should be able to manually BOO will check
erase the programming/data. practically.
11. Remote Operation Capable to operate from BOO will check
remote location through cable. practically.
t2 Audio input Mic and external socket. BOO will check
sockets I practically.

\ I
t."
V
5
,

a
-5-
q
2

s Parameter Specifications Trial Dlrectives


13. Squelch Voice/Digital squelch BOO will check
practically.
t4 hrsh to talk Suitable Microphone to be BOO will check
provided. practically.
1.6 Optional Features
user
1 Communication AES 128 bit or AES 256 bit Firm will submit
Security or SAG approved (As per OEM Certificate.
user requirement)
2 ALB_ 2G IALE 3G ALE 2G as per Appendix Firm will produce
"A" and ALE 3G as Per OEM Certificate.
Appendix "C" of MIL-STD-
188- 14 1B
3 Frequency Hopping Hop Rate: >6 hops per Firm will produce
second OEM certificate.
4 GPS Interface Inbuilt GPS with polling BOO will check
facility practically.
5. Data Terminal Speciflcations:
Should also be compatible with existing HF Radio
a) Processor Intel Core i5 BOO will check
generation / equivalent physically and firm
better will produce OEM
b) Speed 2.5 GHz or better certificate.
c) RAM Minimum 8GB DDR4
(Expendable up to 64 GB or
better)
d) Memory Speed 2133 MHz or better
e) Storage 256 GB or more SD
0 Display Size 14 Inch or more
s) Interface SB, HDMI /DP Port
h) Keyboard ultimedia/ Membrane
i) Mouse Touchpad
i) Operating System WindowslO or
Windows version OS
k) Battery endurance 18 hrs or more with
ba

rl \-/ \,/

v \
-6-
1
s.N Parameter Speciflcations Trial Dlrectives
t
r) Data communication Compatible with Windows BOO will check
software 10 or latest version physically and firm
Windows OS will produce OEM
certificate.
m) Operating Temperature -10'C to +50" C The firm will
n) Storage Temperature -2O"C to +60"C produce certilicate
o) Dust and water IP 53 or better of Govt. Lab. or
resistance test NABL/ILAC
p) Safety Standards MIL-STD-810H or better or accredited
JS-55555 or better laboratory.
q) Drop resistance test 90 cm

(SI/RM. Ashok Kumar Rajwant) (WO/ Verma) t Singh, AC) (G AC


BSF Assam Rifles ITBP SSB

)-y
(H.S.Srihari , Dy.Dir)
,rd
(Viplav Azad, DC) (Maj.Ajay Antil) (Sunil Kr Singh), DC(Comn)
DCPW CISF NSG CRPF

L {
(Amit , DIG(Eqpt) Agrawal),DIG(Comn)
CRPF CRPF

M,. (Zulfiquar Hasan),lPS


(Syed Mohd Husnain)
IG(Comn&IT), CRPF sDG(OPS),CRPF

'r>
(Kuldiep
DG, CRPF

You might also like