Electrical network protection

Protection guide

Guide
 A฀new฀path฀for฀achieving฀
your฀electrical฀installations

A comprehensive offer
The฀Protection฀Guide฀completes฀the฀perfectly฀coordinated฀
offer฀of฀products฀which฀meet฀all฀medium฀and฀low฀voltage฀
electrical฀distribution฀requirements.฀All฀of฀these฀products฀have฀
been฀designed฀to฀work฀together:฀electrical,฀mechanical฀and฀
communication฀compatibility.
The฀electrical฀installation฀is฀thus฀both฀optimised฀and฀has฀improved฀
performance:
b฀better฀service฀continuity,
b฀increased฀personnel฀and฀equipment฀safety,
b฀guaranteed฀upgradeability,
b฀efficient฀monitoring฀and฀control.
You฀therefore฀have฀all฀the฀advantages฀at฀hand฀in฀terms฀of฀
knowhow฀and฀creativity฀for฀achieving฀optimised,฀safe,฀upgradeable฀
and฀compliant฀installations.

Tools for facilitating the design and installation

With฀Schneider฀Electric,฀you฀have฀a฀complete฀range฀of฀tools฀to฀
help฀you฀get฀to฀know฀and฀install฀the฀products฀whilst฀complying฀
with฀current฀standards฀and฀good฀working฀practices.฀These฀tools,฀
technical฀sheets฀and฀guides,฀design฀software,฀training฀courses,฀
etc.฀are฀regularly฀updated.

Schneider฀Electric฀is฀associating฀itself฀
with฀your฀know-how฀and฀your฀creativity฀
to฀produce฀optimised,฀safe,฀upgradeable฀
and฀compliant฀installations
For a real partnership with you
A฀universal฀solution฀doesn’t฀exist฀because฀each฀electrical฀
installation฀is฀specific.฀The฀variety฀of฀combinations฀on฀offer฀allows฀
you฀to฀truly฀customise฀the฀technical฀solutions.
You฀are฀able฀to฀express฀your฀creativity฀and฀put฀your฀know-how฀to฀
best฀advantage฀when฀designing,฀manufacturing฀and฀exploiting฀an฀
electrical฀installation.
Protection guide Contents

Presentation 2
Power-system architecture
Selection criteria 4
Examples of architectures 5
Neutral earthing
Five neutral earthing systems 6
Isolated neutral 7
Resistance earthing 8
Low reactance earthing 9
Compensation reactance earthing 10
Solidly earthed neutral 11
Short-circuit currents
Introduction to short-circuits 12
Types of short-circuit 14
Short-circuit across generator terminals 16
Calculation of short-circuit currents 17
Equipment behaviour during short-circuits 18
Sensors
Phase-current sensors (CT) 19
Phase-current sensors (LPCT) 21
Residual-current sensors 22
Voltage transformers (VT) 23
Protection functions
General characteristics 24
List of functions 26
Associated functions 27
Discrimination
Time-based discrimination 28
Current-based discrimination 30
Logic discrimination 31
Directional protection discrimination 32
Differential protection discrimination 33
Combined discrimination 34
Power-system protection
Single-incomer power systems 36
Dual-incomer power systems 38
Open loop power systems 40
Closed loop power systems 41
Busbar protection
Types of faults and protection functions 42
Link (line and cable) protection
Types of faults and protection functions 44
Transformer protection
Types of faults 46
Protection functions 47
Recommended settings 48
Examples of applications 49
Motor protection
Types of faults 50
Protection functions 51
Recommended settings 53
Examples of applications 54
Generator protection
Types of faults 55
Protection functions 56
Recommended settings 58
Examples of applications 59
Capacitor protection
Types of faults 60
Protection functions 61
Recommended settings and examples of applications 62
Appendices
Glossary - Key words and definitions 64
Bibliography 66
Definitions of symbols 67
Index of technical terms 68

1
 Presentation Protection guide 0

Protection units continuously monitor Introduction

the electrical status of power system Among their multiple purposes, protection devices:
components and de-energize them b contribute to protecting people against electrical hazards,
b avoid damage to equipment (a three-phase short-circuit on medium-voltage
busbars can melt up to 50 kg of copper in one second and the temperature
(for instance by tripping a circuit breaker)
when they are the site of a serious at the centre of the arc can exceed 10 000 °C),
disturbance such as a short-circuit, b limit thermal, dielectric and mechanical stress on equipment,
insulation fault, etc. b maintain stability and service continuity in the power system,
b protect adjacent installations (for example, by reducing induced voltage
in adjacent circuits).
The choice of a protection device is not
In order to attain these objectives, a protection system must be fast, reliable and
the result of an isolated study, but rather one
of the most important steps in the design ensure discrimination.
of the power system. Protection, however, has its limits because faults must first occur before the protection
Based on an analysis of the behaviour of system can react.
Protection therefore cannot prevent disturbances; it can only limit their effects and
their duration. Furthermore, the choice of a protection system is often a technical
electrical equipment (motors, transformers,
etc.) during faults and the phenomena and economic compromise between the availability and safety of the electrical power
produced, this guide is intended to facilitate supply.
your choice of the most suitable protective

Designing power system protection

devices.

The design of protection for a power system can be broken down into two distinct
steps:
b definition of the protection system, also called the protection-system study,
b determination of the settings for each protection unit, also called protection
coordination or discrimination.

Definition of the protection system

This step includes selection of the protection components and a consistent, overall
Order structure suited to the power system.
The protection system is made up of a string of devices including the following (fig. 1):
Interruption
DE57357EN

b measurement sensors (current and voltage) supplying the data required to detect
faults,
b protection relays in charge of continuously monitoring the electrical status
Measurement of the power system up to and including the formulation and emission of orders
to the trip circuit to clear the faulty parts,
Processing
Sensor
b switchgear in charge of clearing faults, such as circuit breakers or combinations
of switches or contactors and fuses.
The protection-system study determines the devices to be used to protect against
Protection
relay
the main faults affecting the power system and the machines:
b phase-to-phase and phase-to-earth short-circuits,
Fig. 1. Protection system.

b overloads,
b faults specific to rotating-machines.
The protection-system study must take the following parameters into account:
b power system architecture and size, as well as the various operating modes,
b the neutral-earthing systems,
b the characteristics of current sources and their contributions in the event of a fault,
b the types of loads,
b the need for continuity of service.

Determination of protection-unit settings

Each protection function must be set to ensure the best possible power system
operation in all operating modes.
The best settings are the result of complete calculations based on the detailed
characteristics of the various elements in the installation.
These calculations are now commonly carried out by specialized software tools
that indicate the behaviour of the power system during faults and provide the
settings for each protection function.

2
 Presentation Protection guide 0

Contents of this guide

This guide is intended for those in charge of designing protection for power systems.
It comprises two parts:
b part 1, Power-system study,
b part 2, Solutions for each application.

Power-system study
This is a theoretical section presenting the information required to carry out a protection-
system study covering the following points:
b power-system architecture - what are the main architectures used in medium-voltage
DE57358

51
51N
power systems?
A

b neutral earthing systems - what are the main neutral earthing systems in medium
voltage and what are the selection criteria?
b short-circuit currents - what are their characteristics, how are they calculated
and how do electrical devices react?
49 b measurement sensors - how should instrument transformers for current
and voltage be used?
B 51
b protection functions - what functions do protection units provide
51N

and what are their codes (ANSI codes)?

b discrimination of protection devices - what techniques must be used to ensure
effective fault clearing?
Precise determination of protection settings is not dealt with in this guide.
Fig. 1. Protection-system study.

Solutions for each application

This section provides practical information on the types of faults encountered
in each application:
DE57304

b power systems,
b busbars,
b lines and cables,
12

b transformers,
14
27D
27R b motors,
b generators,
46

b capacitors,
48฀-฀51LR
49RMS
26 51
and the protection units required for each type of fault, with setting
recommendations and application examples.
63 51G
49T 66
87T

38/
M 49T

Fig. 2. Example of a motor application.

3
Power-system Selection criteria 0

architecture

Protection of a power system depends on Power-system architecture

its architecture and the operating mode. The various components of a power system can be arranged in different ways.
This chapter compares typical structures The complexity of the resulting architecture determines the availability of electrical
energy and the cost of the investment.
Selection of an architecture for a given application is therefore based on a trade-off
of power systems.
between technical necessities and cost.

Architectures include the following:

b radial systems
v single-feeder,
v double-feeder,
v parallel-feeder,
v dual supply with double busbars.
b loop systems
v open loop,
v closed loop.
b systems with internal power generation
v normal source generation,
v replacement source generation.
The table below lists the main characteristics of each architecture for comparison.
Illustrations are provided on the next page.

Architecture Use Advantages Drawbacks

Radial
Single-feeder radial Processes not requiring Most simple architecture Low availability
continuous supply Easy to protect Downtime due to faults may be long
E.g. a cement works Minimum cost A single fault interrupts supply to the entire
feeder
Double-feeder radial Continuous processes: steel, Good continuity of supply Expensive solution
petrochemicals Maintenance possible on busbars Partial operation of busbars during
of main switchboard maintenance
Parallel-feeder Large power systems Good continuity of supply Requires automatic control functions
Future expansion is limited Simple protection
Double busbars Processes requiring high Good continuity of supply Expensive solution
continuity of service Flexible operation: no-break transfers Requires automatic control functions
Processes with major load Flexible maintenance
changes
Loop systems
Open loop Very large power systems Less expensive than closed loop Faulty segment can be isolated during loop
Major future expansion Simple protection reconfiguration
Loads concentrated in Requires automatic control functions
different zones of a site
Closed loop Power system offering high Good continuity of supply Expensive solution
continuity of service Does not require automatic control Complex protection system
Very large power systems functions
Loads concentrated in
different zones of a site
Internal power generation
Normal source Industrial process sites Good continuity of supply Expensive solution
generation producing their own energy Cost of energy (energy recovered
E.g. paper plants, steel from process)
Replacement source Industrial and commercial Good continuity of supply for priority Requires automatic control functions
(source changeover) sites outgoing feeders
E.g. hospitals

4
 Power-system Examples of architectures 0

architecture

Single-feeder radial Double-feeder radial Legend:

NC: normally closed
NC NO: normally open
DE55361

DE55362EN
or
NO Unless indicated
otherwise, all switchgear
is NC.

NO

NO

Parallel-feeder Double busbars

NC
DE55363EN

DE55364EN

or
NO

NC NO NO NC

NC NC
or
NO

NO NC NO NC NO NO NC
NC

NO

Open loop Closed loop

NC NC
DE55365EN

DE55366EN

or or
NO NO

NC NC NC NO NC NC NC NC NC NC NC NC

Local normal source generation Replacement source generation (source changeover)

G G G
DE55367EN

DE55368EN

NO
NC NC
or or source
NO NO changeover

NC

5
 Neutral earthing Five neutral earthing systems 0

The choice of neutral earthing for MV and Earthing impedance

HV power systems has long been a topic of The neutral potential can be earthed by five different methods, according to type
heated controversy due to the fact that (capacitive, resistive, inductive) and the value (zero to infinity) of the impedance ZN
of the connection between the neutral and earth:
b ZN = ×: isolated neutral, i.e. no intentional earthing connection,
it is impossible to find a single compromise
for the various types of power systems. b ZN is related to a resistance with a fairly high value,
Acquired experience now allows an b ZN is related to a reactance, with a generally low value,
appropriate choice to be made according to b ZN is related to a compensation reactance, designed to compensate
for the system capacitance,
b ZN = 0: the neutral is solidly earthed.
the specific constraints of each system.
This chapter compares the different types
of neutral earthing, distinguished by the Difficulties and selection criteria
neutral point connection and the operating The selection criteria involve many aspects:
technique used. b technical considerations (power system function, overvoltages, fault current, etc.),
b operational considerations (continuity of service, maintenance),
b safety,
b cost (capital expenditure and operating expenses),
b local and national practices.
Two of the major technical considerations happen to be contradictory:
Reducing the level of overvoltages
Excessive overvoltages cause the dielectric breakdown of electrical insulating
DE57201

materials, resulting in short-circuits.

Overvoltages are of several origins:
b lightning overvoltage, to which all overhead systems are exposed, up to the user
supply point,
b overvoltage within the system caused by switching and critical situations such as
resonance,
ZN C C C b overvoltage resulting from an earth fault itself and its elimination.
Reducing earth fault current (Ik1) (fig. 1)
Ik1

Fault current that is too high produces a whole series of consequences related to
the following:
b damage caused by the arc at the fault point; particularly the melting of magnetic
circuits in rotating machines,
Fig. 1. Equivalent diagram of a power system b thermal withstand of cable shielding,
with an earth fault. b size and cost of earthing resistor,
b induction in adjacent telecommunication circuits,
b danger for people created by the rise in potential of exposed conductive parts.
Unfortunately, optimizing one of these requirements is automatically to the
disadvantage of the other. Two typical neutral earthing methods accentuate
this contrast:
b isolated neutral, which eliminates the flow of earth fault current through the neutral
but creates higher overvoltages,
b solidly earthed neutral, which reduces overvoltage to a minimum, but causes high
fault current.
As for the operating considerations, according to the neutral earthing method used:
b continued operation may or may not be possible after a persisting first fault,
b the touch voltages are different,
b protection discrimination may be easy or difficult to implement.
An in-between solution is therefore often chosen, i.e. neutral earthing
via an impedance.

Summary of neutral earthing characteristics

Characteristics Neutral earthing
isolated compensated resistance reactance direct
Damping of transient overvoltages – +– + +– ++
Limitation of 50 Hz overvoltages – – + + +
Limitation of fault currents + ++ + + ––
Continuity of service + + – – –
(no tripping required on first fault)
Easy implementation of protection discrimination – –– + + +
No need for qualified personnel – – + + +
Legend: + good
– mediocre

6
 Neutral earthing Isolated neutral 0

Block diagram
There is no intentional earthing of the neutral point, except for measurement
or protection devices.
DE57202

Operating technique
V

In this type of power system, a phase-to-earth fault only produces a low current
through the phase-to-earth capacitances of the fault-free phases (fig. 1).
It can be shown that Ik1 = 3 • C • ω • V where:
b V is the phase-to-neutral voltage,
b C is the phase-to-earth capacitance of a phase,
b ω is the angular frequency of the power system defined as ω = 2 • π • f
C C C
Ik1

The fault current Ik1 can remain for a long time, in principle, without causing
any damage since it is not more than a few amperes (approximately 2 A per km
Ic
for a 6 kV single-core cable with a cross-section of 150 mm2 , XLPE insulation and a
capacitance of 0.63 mF/km). Action does not need to be taken to clear this first fault,
Fig. 1. Capacitive fault current in isolated neutral system. making this solution advantageous in terms of maintaining service continuity.
However, this entails the following consequences:
b the insulation must be continuously monitored and faults that are not yet cleared
must be indicated by an insulation monitoring device or by a neutral voltage
displacement protection unit (ANSI 59N) (fig. 2),
b subsequent fault tracking requires complex automatic equipment for quick
identification of the faulty feeder and also maintenance personnel qualified
DE55203EN

to operate the equipment,

b if the first fault is not cleared, a second fault occurring on another phase will cause
a real two-phase-to-earth short circuit, which will be cleared by the phase protection
units.

Advantage
The basic advantage is service continuity since the very low fault current does not
I MD

cause automatic tripping for the first fault; it is the second fault that requires tripping.

Drawbacks
b The failure to eliminate transient overvoltages through the earth can be a major
Fig. 2. Insulation monitoring device (IMD).

handicap if the overvoltage is high.

b Also, when one phase is earthed, the others reach a phase-to-phase voltage
at power frequency (U = 3 • V) in relation to the earth, and this increases the
probability of a second fault. Insulation costs are higher since the phase-to-phase
voltage may remain between the phase and earth for a long time with no automatic
tripping.
V0 b Insulation monitoring is compulsory, with indication of the first fault.
IrsdB b A maintenance department with the equipment to quickly track the first insulation
fault is required.
DE57204

b It is difficult to implement protection discrimination for the first fault.

V0 V0

b There are risks of overvoltages created by ferroresonance.

Protection function
IrsdA

The faulty feeder may be detected by a directional earth fault protection unit
(ANSI 67N) (fig. 3).
The diagram shows that discrimination is implemented by a comparison of the
phase displacement angle between the residual voltage and residual currents, for
the faulty feeder and for each fault-free feeder.
The current is measured by a core balance CT and the tripping threshold is set:
IrsdA IrsdB b to avoid nuisance tripping,
b lower than the sum of the capacitive currents of all the other feeders.
This makes it difficult for faults to be detected in power systems that are limited
67N 67N
A B
in size, consisting of only a few hundreds of meters of cable.

Ik1 Applications
This solution is often used for industrial power systems (ð 15 kV) that require service
continuity.
It is also used for the public distribution systems in Spain, Italy and Japan.

Fig. 3. Detection for directional earth fault protection.

7
 Neutral earthing Resistance earthing 0

Block diagram
A resistor is intentionally connected between the neutral point and earth.

Operating technique
DE57205

In this type of power system, the resistive impedance limits the earth fault current Ik1
and still allows satisfactory evacuation of overvoltages.
However, protection units must be used to automatically clear the first fault. In power
systems that supply rotating machines, the resistance is calculated so as to obtain
a fault current Ik1 of 15 to 50 A. This low current must however be IRN Š 2 Ic (where
RN Ic is the total capacitive current in the power system) to reduce switching surges and
allow simple detection.
IRN Ik1
In distribution power systems, higher values are used (100 to 300 A) since they are
easier to detect and allow the evacuation of lightning overvoltages.

Advantages
Ic

b This system is a good compromise between low fault current and satisfactory
Fig. 1. Earthing with accessible neutral:

overvoltage evacuation.
resistor between neutral and earth.

b It does not require equipment with phase-to-earth insulation sized for the phase-
to-phase voltage.
b The protection units are simple and selective and the current is limited.
DE55200

Drawbacks
b The service continuity of the faulty feeder is downgraded and earth faults must be
cleared as soon as they occur (first fault tripping).
b The higher the voltage and the current limited, the higher the cost of the earthing
RN resistor.

Neutral earthing
b If the neutral point is accessible (star-connected windings with an accessible
neutral), the earthing resistor may be connected between the neutral and earth (fig. 1)
Fig. 2. Earthing with accessible neutral:

or via a single-phase transformer with an equivalent resistive load on the secondary

resistor on single-phase transformer secondary circuit.

winding (fig. 2).

b When the neutral is not accessible (delta-connected winding) or when the protection
system study shows that it is appropriate, an artificial neutral point is created using a
zero sequence generator connected to the busbars; it consists of a special
DE55206

transformer with a very low zero sequence reactance.

v star-delta transformer with solidly earthed primary neutral, and a delta connection
including a limiting resistor (LV insulation, therefore the most inexpensive solution)
(fig. 3),
v star-delta transformer with limiting resistor (HV insulation) between the primary
neutral point and earth, and a closed delta connection (no resistor); this solution
is less often used (fig. 4).

Protection functions
RN

To detect a fault current Ik1 that is low, protection functions other than phase
RN overcurrent are required (fig. 5).
These “earth fault’’ protection functions detect fault current:
b directly in the neutral earthing connection 1,
Earthing with inaccessible neutral:

b or in the power system by the vector sum of the 3 currents measured by:
Fig. 3. Limiting resistor Fig. 4. Limiting resistor on

v 3 current sensors supplying the protection units 2,

on secondary circuit. primary circuit.

v or a core balance CT 3: preferred method since more accurate.

The threshold is set according to the fault current Ik1 calculated without taking
into account the source and connection zero sequence impedance in relation to
DE57208

the impedance RN, in compliance with two rules:

b setting > 1.3 times the capacitive current of the power system downstream
from the protection unit,
b setting in the range of 10 to 20% of the maximum earth fault current.
In addition, if 3 CTs are used for detection, in view of current technologies, the
1 2 3 setting should be within 5 to 30% of the CT rating to account for the uncertainty
51G 51G linked to:
b transient current asymmetry,
RN 51N b CT saturation,
b scattering of performance.

Fig. 5. Earth fault protection solutions. Applications

Public and industrial MV distribution systems.

8
 Neutral earthing Low reactance earthing 0

Block diagram
A reactor is intentionally connected between the neutral point and earth.
For power system voltages greater than 40 kV, it is preferable to use a reactor rather
than a resistor because of the difficulties arising from heat emission in the event
of a fault (fig. 1).

Operating technique
DE57209

In this type of power system, an inductive impedance limits earth fault current Ik1 and
still allows satisfactory evacuation of overvoltages. However, protection units must
be used to automatically clear the first fault.
To reduce switching surges and allow simple detection, the current IL must be much
higher than the total capacitive current of the power system Ic.
LN In distribution systems, higher values are used (300 to 1000 A) since they are easier
to detect and allow the evacuation of lightning overvoltages.
ILN Ik1

Advantages
b This system limits the amplitude of fault currents.
Ic

b Protection discrimination is easy to implement if the limiting current is much greater

Fig. 1. Earthing with accessible neutral. than the capacitive current in the power system.
b The coil has a low resistance and does not dissipate a large amount of thermal
energy; the coil can therefore be reduced in size.
b In high voltage systems, this solution is more cost-effective than resistance earthing.

Drawbacks
b The continuity of service of the faulty feeder is downgraded; earth faults must be
cleared as soon as they occur (first fault tripping).
b When earth faults are cleared, high overvoltages may occur due to resonance
between the power system capacitance and the reactance.

Neutral earthing
b If the neutral point is accessible (star-connected windings with an accessible
neutral), the earthing reactance may be connected between the neutral and earth.
b When the neutral is not accessible (delta-connected winding) or when the protection
system study shows that it is appropriate, an artificial neutral point is created by
DE55210

a neutral point coil connected to the busbars; it consists of a zigzag coil with
an accessible neutral (fig. 2).
The impedance between the two parts of the winding, essentially inductive and low,
limits the current to values that remain greater than 100 A.
A limiting resistor may be added between the coil neutral point and earth to reduce
the amplitude of the fault current (HV insulation).

Protection functions
LN

b The protection setting is in the range of 10 to 20% of the maximum fault current.
b The protection function is less restrictive than in the case of resistance earthing,
especially considering the high value of ILN given that Ic is less than the limited
Fig. 2. Earthing with inaccessible neutral. current.

Applications
Public and industrial MV distribution systems (currents of several hundred amperes).

9
 Neutral earthing Compensation reactance
earthing 0

Block diagram
A reactor tuned to the total phase-to-earth capacitance of the power system
is inserted between the neutral point and earth so that the fault current is close
to zero if an earth fault occurs (fig. 1).
DE57211

Operating technique
This system is used to compensate for capacitive current in the power system.
The fault current is the sum of the currents flowing through the following circuits:
b reactance earthing circuit,
b fault-free phase capacitances with respect to earth.
R LN The currents compensate for each other since:
Ik1
b one is inductive (in the earthing circuit),
b the other one is capacitive (in the fault-free phase capacitances).
They therefore add up in opposite phase.
ILN฀+฀IR Ic In practice, due to the slight resistance of the coil, there is a low resistive current
of a few amperes (fig. 2).

Advantages
Fig. 1. Earth fault in power system with compensation
reactance earthing.

IL b The system reduces fault current, even if the phase-to-earth capacitance is high:
spontaneous extinction of non-permanent earth faults.
DE55212EN

current฀in฀the฀reactor
b The touch voltage is limited at the location of the fault.
Ik1 b The installation remains in service even in the event of a permanent fault.
b The first fault is indicated by detection of current flowing through the coil.

Drawbacks
V0
IR residual฀voltage

b The cost of reactance earthing may be high since the reactance needs
to be modified to adapt compensation.
Ic

b It is necessary to make sure that the residual current in the power system during
capacitive฀current
Fig. 2. Vector diagram of currents during an earth fault.
the fault is not dangerous for people or equipment.
b There is a high risk of transient overvoltages on the power system.
b Personnel must be present to supervise.
b It is difficult to implement protection discrimination for the first fault.

Protection function
Fault detection is based on the active component of the residual current.
The fault creates residual currents throughout the power system, but the faulty
circuit
is the only one through which resistive residual current flows.
In addition, the protection units must take into account repetitive self-extinguishing
faults (recurrent faults).
When the earthing reactance and power system capacitance are tuned
(3 LN • C • ω2 = 1)
b fault current is minimal,
b it is a resistive current,
b the fault is self-extinguishing.
The compensation reactance is called an extinction coil, or Petersen coil.

Application
Public and industrial MV distribution systems with high capacitive current.

10
 Neutral earthing Solidly earthed neutral 0

Block diagram
An electrical connection with zero impedance is intentionally set up between
the neutral point and earth.
DE57213

Operating technique
Since the neutral is earthed without any limiting impedance, the phase-to-earth fault
current Ik1 is practically a phase-to-neutral short-circuit, and is therefore high (fig. 1).
Tripping takes place when the first insulation fault occurs.

Advantages
b This system is ideal for evacuating overvoltages.
IN
Ik1
b Equipment with insulation sized for phase-to-neutral voltage may be used.
b Specific protection units are not required: the normal phase overcurrent protection
Ic units can be used to clear solid earth faults.

Fig. 1. Earth fault in a solidly earthed neutral power system. Drawbacks

b This system involves all the drawbacks and hazards of high earth fault current:
maximum damage and disturbances.
b There is no service continuity on the faulty feeder.
b The danger for personnel is high during the fault since the touch voltages created
are high.

Protection function
Impedant faults are detected by a delayed earth fault protection unit (ANSI 51N),
set in the range of the rated current.

Applications
b This type of system is not used in European overhead or underground MV power
systems, but is prevalent in North American distribution systems. In the North
American power systems (overhead systems), other features come into play
to justify the choice:
v distributed neutral conductor,
v 3-phase or 2-phase + neutral or phase + neutral distribution,
v use of the neutral conductor as a protective conductor with systematic earthing
at each transmission pole.
b This type of system may be used when the short-circuit power of the source is low.

11
 Short-circuit currents Introduction to short-circuits 0

A short-circuit is one of the major incidents Definitions

affecting power systems. b A short-circuit is an accidental connection between conductors by a zero
This chapter describes short-circuits and (solid short-circuit) or non-zero impedance (impedant short-circuit).
b A short-circuit is referred to as internal if it is located within equipment or external
their effects on power systems and their if its occurs on links.
interaction with equipment. b The duration of a short-circuit is variable. A short-circuit is said to be
It also provides a method and the main self-extinguishing if its duration is too short for tripping of the protection devices,
equations to calculate currents and voltages transient if cleared following tripping and reclosing of the protection devices
and continuous or sustained if it does not disappear following tripping.
when short-circuits occur. b The causes of a short-circuit can be mechanical (a shovel, a branch, an animal),
electrical (damaged insulation, overvoltages) or human (operating error) (fig. 1).

Effects of short-circuit currents

The consequences are often serious, if not dramatic.
b A short-circuit disturbs the power system environment around the fault point by
R X
DE57355EN

causing a sudden drop in voltage.

b It requires disconnection, through the operation of the protection devices,
Isc
A
of a part (often large) of the installation.
Zsc

b All equipment and connections (cables, lines) subjected to a short-circuit

E are subjected to high mechanical stress (electrodynamic forces) that can cause
breaks and thermal stress that can melt conductors and destroy insulation.
b At the fault point, there is often a high-energy electrical arc, causing very heavy
damage that can quickly spread.
B

Although short-circuits are less and less likely to occur in modern, well-designed,
well-operated installations, the serious consequences they can cause are an incentive
to implement all possible means to swiftly detect and eliminate them.
Ia฀=฀I฀•฀sin(ω฀t฀+฀α)
DE55356EN

– R •฀t
The short-circuit current at different points in the power system must be calculated to
design the cables, busbars and all switching and protection devices and determine
Ic฀=฀–฀I฀•฀sinα฀•฀e L

I
t their settings.

α
Characterization of short-circuits
A number of types of short-circuits can occur in a power system.
b Three-phase short-circuit: a fault between the three phases.
Isc฀=฀Ia฀+฀Ic This type generally provokes the highest currents (fig. 2).
b Phase-to-earth short-circuit: a fault between a phase and earth.
This type is the most frequent (fig. 3).
Moment฀fault฀occurs
Fig. 1. Graphical representation of a short-circuit current based b Two-phase short-circuit clear of earth: a fault between two phases (phase-to-
on an equivalent diagram.
phase voltage). The resulting current is lower than for a three-phase short-circuit,
except when the fault is in the immediate vicinity of a generator (fig. 4).
b Two-phase-to-earth short-circuit: a fault between two phases and earth (fig. 5).
Ph฀1 Ph฀1
DE57215

Ph฀2 Ph฀2

Ph฀3 Ph฀3

Fig. 2. Three-phase short-circuit (5% of cases). Fig. 4. Two-phase short-circuit clear of earth.

Ph฀1 Ph฀1
DE57216

Ph฀2 Ph฀2

Current฀(I) Ph฀3 Ph฀3

DE55229EN

Fig. 3. Phase-to-earth short-circuit (80% of cases). Fig. 5. Two-phase-to-earth short-circuit.

DC฀component

Short-circuit current at a given point in the power system is expressed as the rms
Ip value Ik (in kA) of its AC component (fig. 6).
The maximum instantaneous value that short-circuit current can reach is the peak
value Ip of the first half cycle. This peak value can be much higher than 2 • Ik
because of the damped DC component IDC that can be superimposed on the AC
2฀2฀Ik

Time component.
(t) This DC component depends on the instantaneous value of the voltage at the start
of the short-circuit and on the power system characteristics. The power system
is defined by the short-circuit power, according to the equation:
Fig. 6. Typical short-circuit current curve. Ssc = 3 • Un • Ik (in MVA).
This theoretical value has no physical reality; it is a practical conventional value
comparable to an apparent power rating.

12
Short-circuit currents Introduction to short-circuits 0

Symmetrical components
During normal, balanced symmetrical operation, analysis of three-phase systems is
similar to that of an equivalent single-phase system, characterized by the phase-to-
neutral voltages, phase currents and power system impedances (called cyclical
impedances). As soon as a significant dissymmetry appears in the configuration or
in power system operation, simplification is no longer possible. It is not possible to
establish simple electrical relations in the conductors, using the cyclical
impedances.
In this case, the symmetrical-components method is used, which consists of
expressing the real system as a superposition of three independent, single-phase
power systems, called:
b positive sequence (designated by a subscript 1, e.g. V1),
b negative sequence (designated by a subscript 2, e.g. V2),
b zero-sequence (designated by a subscript 0, e.g. V0).
For each system (positive-, negative- and zero-sequence respectively), voltages
V1, V2, V0 and currents I1, I2, I0 are related by the impedances Z1, Z2, Z0 of the same
system.
The symmetrical impedances are a function of the real impedances, notably
the mutual inductances.
The notion of symmetrical components is also applicable to power.

V1 = V 1 + V 2 + V 0 V1 = 1
--- (V1 + a • V2 + a2 • V3 )
3
V2 = a2 • V 1 + a • V2 + V0 1- (V1 + a2 • V2 + a • V3 )
V 2 = --
3
V3 = a • V1 + a2 • V2 + V0
V0 = 1
--- (V1 + V2 + V3 )
3

where where
2π 2π
j • ------ j • ------
3 a = e 3
a = e

Positive฀sequence Negative฀sequence Zero฀sequence

V31 V10
V2 2
DE55214EN

V3
V1 V11 V1 2 V20
ωt
V30
V2 ωt
ωt V3 2 ωt
V21
Decomposition of a three-phase system into symmetrical components

Decomposition into symmetrical components is not simply a mathematical technique,

it corresponds to the physical reality of the phenomena. It is possible to directly
measure the symmetrical components (voltages, currents, impedances)
of an unbalanced system.
The positive-, negative- and zero-sequence impedances of an element in the power
system are the impedances of the element subjected to voltage systems that are,
respectively, positive three-phase, negative three-phase and phase-to-earth
on three parallel phases.
Generators produce the positive-sequence component and faults may produce
the negative and zero-sequence components.
In the case of motors, the positive-sequence component creates the useful rotating
field, whereas the negative-sequence component creates a braking rotating field.
For transformers, an earth fault creates a zero-sequence component that produces
a zero-sequence field passing through the tank.

13
 Short-circuit currents Types of short-circuit 0

Three-phase short-circuit between the phase

conductors (fig. 1)
The value of the three-phase short-circuit current at a point F within the power system is:
Ik3
F
DE57217EN

Zsc
U
Ik3 = ----------------------
U √3 • Zsc
where U refers to the phase-to-phase voltage at point F before the fault occurs and
Zsc is the equivalent upstream power system impedance as seen from the fault point.
Zsc

In theory, this is a simple calculation; in practice, it is complicated due to the difficulty

of calculating Zsc, an impedance equivalent to all the unitary impedances of series
and parallel-connected units located upstream from the fault. These impedances
Zsc
are themselves the quadratic sum of reactances and resistances.
ZN Zs c = R2 + X2
Calculations can be made much simpler by knowing the short-circuit power Ssc
at the connection point for utility power. It is possible to deduce the equivalent
impedance Za upstream of this point.
Fig. 1. Three-phase short-circuit.
2
U----
Za = --- - I sc = ---------U
---
Ssc 3 • Za
Similarly, there may not be a single source of voltage, but rather several sources
in parallel, in particular, synchronous and asynchronous motors which act
as generators when short-circuits occur.
The three-phase short-circuit current is generally the strongest current that can flow
in the power system.

V1

DE55219EN
E Z1
I1
I 1 = --E
---- V2
Z1
Z2
I2 = I0 = 0 I2
V 1 = V2 = V 0 = 0 V0
Z0
I0
Model of a three-phase short-circuit using the symmetrical components.

Single-phase short-circuit between a phase

conductor and earth (fig. 2)
Zsc
DE57218EN

U The value of this current depends on the impedance ZN between the neutral
and earth. This impedance can be virtually nil if the neutral is solidly earthed
(in series with the earthing resistance) or, on the contrary, almost infinite if the
Zsc

neutral is isolated (in parallel with the power system phase-to-earth capacitance).
Zsc The value of the phase-to-earth fault current is:
3----•----U
Ik1 = ------------------------ ----------------------
( Z 1 + Z 2 + Z 0 + 3Z N)

This calculation is required for power systems in which the neutral is earthed by
ZN
Ik1
an impedance ZN. It is used to determine the setting of the “earth fault” protection
devices which must break the earth-fault current.
If Z1, Z2 and Z0 are negligible with respect to ZN, then:
U
Ik1 = ---------------------
Fig. 2. Phase-to-earth short-circuit. 3 • ZN
This is the case, for example, when Ik1 is limited to 20 A in an MV power system
supplied by a high-power transformer (10 MVA).

I 1 = I 2 = I 0 = ---------------------E
----------------------- V1
DE55220EN

Z 1 + Z 2 + Z 0 + 3Z E Z1
I1
E( Z + Z + 3Z )
V 1 = -------------2------------0------------------- V2
Z 1 + Z 2 + Z 0 + 3Z
Z2
–Z • E I2
V 2 = ---------------------2-----------------------
Z 1 + Z 2 + Z 0 + 3Z V0
–Z • E Z0
V 0 = ---------------------0----------------------- I0
Z 1 + Z 2 + Z 0 + 3Z
3Z

Model of a phase-to-earth short-circuit using the symmetrical components.

14
 Short-circuit currents Types of short-circuit 0

Two-phase short-circuit between phase conductors (fig.1)

The value of the two-phase short-circuit current at a point within the power system is:
Zsc I k2 = --------U
----------
DE57221EN

Z1 + Z 2
U In a power system supplied by a transformer (fault far from the sources), the value of
Zsc the two-phase short-circuit current at a point within the power system is:
Ik2 = -------U
-----------
2 • Zsc
The two-phase short-circuit current is weaker than three-phase short-circuit current,
Ik2

by a ratio of 3/2, i.e. approximately 87%.

Zsc
If the fault occurs close to a generator (Z2 ð Z1), the current can be higher
ZN than in a three-phase fault.

E
I 1 = ----------------------------

DE55224EN
Z1 + Z2 + Z
Fig. 1. Two-phase short-circuit clear of earth. V1
–E E Z1
I 2 = ----------------------------
Z1 + Z2 + Z I1
Z
I0 = 0 V2
Z2
E( Z + Z ) I2
V 1 = --------------2--------------
Z1 + Z2 + Z V0
E•Z Z0
V 2 = --------------------2-------- I0
Z1 + Z2 + Z
V0 = 0

Model of a two-phase short-circuit using the symmetrical components.

Two-phase short-circuit between two phase

conductors and earth (fig. 2)
Zsc
DE57222EN

U For a solid short-circuit (fault far from the sources), the value of the two-phase-
to-earth short-circuit is:
Zsc
Ik2E 3•U
IkE2E = ---------------------------
(Z + 2Z )

Zsc V1
DE55225EN

E ( Z + Z + 3Z ) Z1
IkE2E I 1 = -------------------------------2------------0----------------------------------- E
Z 1 • Z 2 + (3Z + Z0 ) • ( Z 1 + Z 2 ) I1
ZN
–E (Z + 3 Z ) V2
I2 = ---------------------------------------0--------------------------------------- Z2
Z 1 • Z 2 + (3Z + Z0 ) • ( Z 1 + Z 2 )
I2
–E • Z V0 3Z
I 0 = -----------------------------------------------2-------------------------------
Z 1 • Z 2 + ( 3Z + Z0 ) • ( Z 1 + Z 2) Z0
Fig. 2. Two-phase-to-earth short-circuit. I0

Model of a two-phase-to-earth short-circuit using the symmetrical components.

15
 Short-circuit currents Short-circuit across generator
terminals 0

It is more complicated to calculate short-circuit current across the terminals

of a synchronous generator than across the terminals of a transformer connected
Current to the power system.
This is because the internal impedance of the machine cannot be considered constant
DE55223EN

Subtransient Transient Steady-state after the start of the fault. It increases progressively and the current becomes weaker,
passing through three characteristic stages:
b subtransient (approximately 0.01 to 0.1 second), the short-circuit current
(rms value of the AC component) is high, 5 to 10 times the rated continuous current.
b transient (between 0.1 and 1 second), the short-circuit current drops to between
I1

2 and 6 times the rated current.

t

I2 b steady-state, the short-circuit current drops to between 0.5 and 2 times the rated
t current.
The given values depend on the power rating of the machine, its excitation mode and,
I3 for the steady-state current, on the value of the exciting current, therefore on the
t load on the machine at the time of the fault.
What is more, the zero-sequence impedance of the AC generators is generally
2 to 3 times lower than their positive-sequence impedance. The phase-to-earth
short-circuit current is therefore greater than the three-phase current.
By way of comparison, the steady-state three-phase short-circuit current across
the terminals of a transformer ranges between 6 and 20 times the rated current,
Moment฀fault฀occurs

Fig. 1. Typical curves for short-circuit currents across generator

depending on the power rating.
It can be concluded that short-circuits across generator terminals are difficult
terminals.

to assess, in particular their low, decreasing value makes protection setting difficult.
Current
DE55228EN

Subtransient฀component

Transient฀component

Steady-state฀component

DC฀component

Total-current฀curve

t
Subtransient Transient Steady-state
Fig. 2. Decomposition of the short-circuit current.

16
 Short-circuit currents Calculation of short-circuit currents 0

IEC method (standard 60909)

The rules for calculating short-circuit currents in electrical installations are presented
Current฀(I) in IEC standard 60909, issued in 2001.
The calculation of short-circuit currents at various points in a power system can
DE55226EN

quickly turn into an arduous task when the installation is complicated.

2฀2฀I"k

The use of specialized software accelerates calculations.

2฀2฀Ib IDC This general standard, applicable for all radial and meshed power systems, 50 or 60 Hz
and up to 550 kV, is extremely accurate and conservative.
It may be used to handle the different types of solid short-circuit (symmetrical or
2฀2฀Ik

Ip dissymmetrical) that can occur in an electrical installation:

b three-phase short-circuit (all three phases), generally the type producing
the highest currents,
b two-phase short-circuit (between two phases), currents lower than three-phase faults,
Time b two-phase-to-earth short-circuit (between two phases and earth),
(t) b phase-to-earth short-circuit (between a phase and earth), the most frequent type
(80% of all cases).
When a fault occurs, the transient short-circuit current is a function of time
t฀min

Fig. 1. Graphic representation of short-circuit quantities and comprises two components (fig. 1):
as per IEC 60909. b an AC component, decreasing to its steady-state value, caused by the various
rotating machines and a function of the combination of their time constants,
b a DC component, decreasing to zero, caused by the initiation of the current
and a function of the circuit impedances.
Practically speaking, one must define the short-circuit values that are useful
in selecting system equipment and the protection system:
b I’’k: rms value of the initial symmetrical current,
Type of I’’k b Ib: rms value of the symmetrical current interrupted by the switching device when
short-circuit the first pole opens at t min (minimum delay),
b Ik: rms value of the steady-state symmetrical current,
3-phase ----•------Un
--c ------- b Ip: maximum instantaneous value of the current at the first peak,
b IDC: DC value of the current.
3 • Z1

These currents are identified by subscripts 3, 2, 2E, 1, depending on the type of short-
2-phase circuit, respectively three-phase, two-phase clear of earth, two-phase-to-earth,
c----•----Un
-- --------
phase-to-earth.
Z1 + Z2

2-phase-to-earth
c • Un • 3 • Z2
-----------------------------------------------------
-------------- The method, based on the Thevenin superposition theorem and decomposition into
symmetrical components, consists in applying to the short-circuit point an equivalent
Z1 • Z2 + Z2 • Z0 + Z1 • Z0

source of voltage in view of determining the current. The calculation takes place in
Phase-to-earth three steps.
-c •----
------ --------•
Un ----------3--
Z1 + Z2 + Z0
b Define the equivalent source of voltage applied to the fault point. It represents the
Short-circuit currents as per IEC 60909 (general situation). voltage existing just before the fault and is the rated voltage multiplied by a factor
taking into account source variations, transformer on-load tap changers and the
Type of I’’k subtransient behavior of the machines.
short-circuit b Calculate the impedances, as seen from the fault point, of each branch arriving
at this point. For positive and negative-sequence systems, the calculation does not
take into account line capacitances and the admittances of parallel, non-rotating
3-phase
c----•----Un
--- --------
3 • Z1 loads.
b Once the voltage and impedance values are defined, calculate the characteristic
2-phase ----•
c Un
------
----- minimum and maximum values of the short-circuit currents.
2 • Z1

The various current values at the fault point are calculated using:
2-phase-to-earth b the equations provided,
c-----•----Un
---------•
----------3
-
b a summing law for the currents flowing in the branches connected to the node:
Z 1 + 2Z0
v I’’k, see the equations for I’’k in the tables opposite, where voltage factor c is defined
Phase-to-earth by the standard; geometric or algebraic summing,
c-----•----Un
---------•----------3
-
v ip = κ • 2 • I’’k, where k is less than 2, depending on the R/X ratio of the positive-
2Z1 + Z 0

Short-circuit currents as per IEC 60909 (distant faults). sequence impedance for the given branch; peak summing,
v Ib = μ • q • I’’k, where m and q are less than 1, depending on the generators
and motors, and the minimum current interruption delay; algebraic summing,
v Ik = I’’k, when the fault is far from the generator,
v Ik = λ • Ir, for a generator, where Ir is the rated generator current and λ is a factor
depending on its saturation inductance; algebraic summing.

17
 Short-circuit currents Equipment behaviour
during short-circuits 0

Characterization
There are 2 types of system equipment, based on whether or not they react when
Current฀(I) a fault occurs.
DE55227EN

Passive equipment
This category comprises all equipment which, due to its function, must have
the capacity to transport both normal current and short-circuit current.
IAC

This equipment includes cables, lines, busbars, disconnecting switches, switches,

transformers, series reactances and capacitors, instrument transformers.
For this equipment, the capacity to withstand a short-circuit without damage
is defined in terms of:
b electrodynamic withstand (expressed in kA peak), characterizing mechanical
resistance to electrodynamic stress,
b thermal withstand (expressed in rms kA for 1 to 5 seconds), characterizing
Time฀(t)

maximum permissible heat rise.

IDC

IAC: peak of the periodic component.

Active equipment
IDC: aperiodic component. This category comprises the equipment designed to clear short-circuit currents, i.e.
circuit breakers and fuses. This property is expressed by the breaking capacity and,
Fig. 1. Rated breaking current of a circuit breaker subjected to if required, the making capacity when a fault occurs.
a short-circuit as per IEC 60056. Breaking capacity (fig. 1)
This basic characteristic of a current interrupting device is the maximum current
(in rms kA) it is capable of breaking under the specific conditions defined by the
standards; it generally refers to the rms value of the AC component of the short-circuit
current. Sometimes, for certain switchgear, the rms value of the sum
of the 2 components (AC and DC) is specified, in which case, it is the “asymmetrical
current”.
The breaking capacity depends on other factors such as:
v voltage,
v R/X ratio of the interrupted circuit,
v power system natural frequency,
v number of breaks at maximum current, for example the cycle: O - C/O - C/O
(O = opening, C = closing),
v device status after the test.
The breaking capacity is a relatively complicated characteristic to define and it
therefore comes as no surprise that the same device can be assigned different
breaking capacities depending on the standard by which it is defined.
Short-circuit making capacity
In general, this characteristic is implicitly defined by the breaking capacity because
a device should be able to close for a current that it can break.
Sometimes, the making capacity needs to be higher, for example for circuit breakers
protecting generators.
The making capacity is defined in terms of the kA peak because the first asymmetric
peak is the most demanding from an electrodynamic point of view.
For example, according to standard IEC 60056, a circuit breaker used in a 50 Hz
power system must be able to handle a peak making current equal to 2.5 times the
rms breaking current.
Prospective short-circuit breaking current
Some devices have the capacity to limit the fault current to be interrupted.
Their breaking capacity is defined as the maximum prospective breaking current that
would develop during a solid short-circuit across the upstream terminals of the device.

Specific device characteristics

The functions provided by various interrupting devices and their main constraints
are presented in the table below.
Device Isolation Current switching Main constraints
conditions
Normal Fault
Disconnector yes no no Longitudinal input/output isolation
Earthing switch: short-circuit making capacity
Switch no yes no Making and breaking of normal load current
Short-circuit making capacity
With a fuse: short-circuit breaking capacity in fuse no-blow zone
Contactor no yes no Rated making and breaking capacities
yes, if withdrawable Maximum making and breaking capacities
Duty and endurance characteristics
Circuit breaker no yes yes Short-circuit breaking capacity
yes, if withdrawable Short-circuit making capacity
Fuse no no yes Minimum short-circuit breaking capacity
Maximum short-circuit breaking capacity

18
 Sensors Phase-current sensors (CT) 0

Protection and measuring devices require The role of a phase-current sensor is to provide its secondary winding with a current
proportional to the measured primary current. They are used for both measurements
and protection.
data on the electrical rating of the equipment
to be protected. There are two types of sensors:
For technical, economic and safety reasons, b current transformers (CT),
this data cannot be obtained directly b current transformers with a voltage output (LPCT).

General characteristics (fig. 1)

from the high-voltage power supply
of the equipment. The following intermediary
devices are needed: The current transformer is made up of two circuits, the primary and the secondary,
coupled by a magnetic circuit.
When there are a number of turns in the primary circuit, the transformer is of the wound-
b phase-current sensors,
b core balance CTs to measure earth fault primary type.
currents, When the primary is a single conductor running through a sensor, the transformer
b voltage transformers (VT). may be of the bar-primary type (integrated primary made up of a copper bar), support
type (primary formed by an uninsulated conductor of the installation) or the toroidal
type (primary formed by an insulated cable of the installation).
These devices fulfill the following functions:
b reduction of the value to be measured
(e.g. 1500/5 A), The CTs are characterized by the following values (according to standard IEC 60044)(1).
b galvanic isolation, CT rated insulation level
b provision of the power required for data This is the highest voltage applied to the CT primary.
Note that the primary is at the HV voltage level and that one of the secondary
terminals is generally earthed.
processing and for the protection function
itself. Similar to other equipment, the following values are defined:
b maximum1 min. withstand voltage at power frequency,
b maximum impulse withstand voltage.
Example. For a 24 kV rated voltage, the CT must withstand 50 kV for 1 minute at 50 Hz
and an impulse voltage of 125 kV.
Rated transformation ratio
It is usually given as the transformation ratio between primary and secondary current
Ip/Is.
The rated secondary current is generally 5 A or 1 A.
Accuracy
It is defined by the composite error for the accuracy-limit current.
The accuracy-limit factor is the ratio between the accuracy-limit current and the
rated current.
b For class P:
5P10 means 5% error for 10 In and 10P15 means 10% error for 15 In,
5P and 10P are the standard accuracy classes for protection CTs,
P1 Ip
DE57330

5 In, 10 In, 15 In, 20 In are the standard accuracy-limit currents.

Is b The PR class is defined by the remanence factor, the ratio between the remanent
flux and the saturation flux, which must be less than 10%.
S1

S2 5PR and 10PR are the standard accuracy classes for protection CTs.
b Class PX is another way of specifying CT characteristics based on the “knee-point
P2 voltage”, the secondary resistance and the magnetizing current (see next page, fig. 1,
Ip: primary current CT response in saturated state).
Is: secondary current (proportional to Ip and in phase)
Rated output
Fig. 1. Current transformer. This is the apparent power in VA that the CT is intended to supply to the secondary
circuit at the rated secondary current without causing the errors to exceed the values
specified.
It represents the power consumed by all the connected devices and cables.
If a CT is loaded at a power lower than its rated output, its actual accuracy level
is higher than the rated accuracy level. Likewise, a CT that is overloaded loses accuracy.
Short time withstand current
Expressed in kA rms, the maximum current permissible for 1 second (Ith)
(the secondary being short-circuited) represents the thermal withstand of the CT
to overcurrents. The CT must be able to withstand the short-circuit current for the time
required to clear it. If the clearing time t is other than 1 sec., the current the CT can
withstand is I th ⁄ t
Electrodynamic withstand expressed in kA peak is at least equal to 2.5 • Ith
Normal values of rated primary currents (in A):
10 - 12.5 - 15 - 20 - 25 - 30 - 40 - 50 - 60 - 75 and multiples or decimal submultiples.

(1) Also to be taken into account are elements related to the type of assembly,
characteristics of the site (e.g. temperature, etc.), power frequency, etc.

19
 Sensors Phase-current sensors (CT) 0

CT response in saturated state

When subjected to a very high primary current, the CT becomes saturated.
The secondary current is no longer proportional to the primary current. The current
error which corresponds to the magnetization current increases significantly.
Knee-point voltage (fig. 1)
This is the point on the current transformer magnetization curve at which a 10%
increase in voltage E requires a 50% increase in magnetization current Im.
E
P1 Ip
DE57331EN

Vk 10%

R
C
T฀
Is

+฀
R
RCT Rwire

w
ire
฀+
Im

฀R
S1 50%

lo
E Lm Vs Rload

ad
S2
Isecondary Imagnetizing
Isat Isn Im฀at฀Vk 1.5฀Im
P2
Fig. 1. Equivalent diagram of a CT secondary current... and CT magnetization curve.

The CT secondary satisfies the equation:

(RCT + Rload + Rwire) • ALF • Isn2 = constant
where Isn = rated secondary current
ALF = accuracy-limit factor
Isat = ALF • Isn

CT for phase overcurrent protection

For definite-time overcurrent protection, if saturation is not reached at 1.5 times
the current setting, operation is ensured no matter how high the fault current (fig. 2).
For IDMT overcurrent protection, saturation must not be reached at 1.5 times the
current value corresponding to the maximum in the useful part of the operation curve
(fig. 3).
t t
DE55332EN

x฀1.5 x฀1.5

I I
Isetting Isaturation Iscmax Isaturation

Fig. 2. Fig. 3.

CT for differential protection (fig. 4)

The CTs should be specified for each application, according to the operating principle
of the protection unit and to the protected component. Refer to the instruction manual
of the protection unit.
Protected฀zone
P1 P2 P2 P1
DE57334EN

Differential฀protection฀

Fig. 4.

20
 Sensors Phase-current sensors (LPCT) 0

Low-power current transducers (LPCT) (fig. 1)

These are special voltage-output sensors of the Low-Power Current Transducer
(LPCT) type, compliant with standard IEC 60044-8.
P1 Ip

LPCTs are used for measurement and protection functions.

DE57336

They are defined by:

S1

b the rated primary current,

Vs
S2 b the rated extended primary current,
b the rated accuracy-limit primary current.
They have a linear output over a wide current range and begin to saturate at levels
P2
Fig. 1. LPCT-type current sensors. above the currents to be interrupted.
Example of measurement characteristics as per IEC 60044-8
b Rated primary current Ipn = 100 A
b Rated extended primary current Ipe = 1250 A
b Secondary voltage Vsn = 22.5 mV
b Class 0.5:
v accuracy 0.5% from 100 A to 1250 A,
v accuracy 0.75% at 20 A,
v accuracy 1.5% at 5 A.
Example of protection characteristics as per IEC 60044-8
b Primary current Ipn = 100 A
b Secondary voltage Vsn = 22.5 mV
b Class 5P from 1.25 kA to 40 kA (fig. 2).

Module
(%)
DE55337EN

5%

1.5%

0.75%
Module
0.5%
Ip

Phase
(min)
90'

60'
45'
Phase
30'

Ip
5฀A 20฀A 100฀A 1฀kA 1.25 10 40
kA kA kA
Fig. 2. LPCT accuracy characteristics.

21
 Sensors Residual-current sensors 0

Zero-sequence current - residual current

The residual current characterizing the earth-fault current is equal to the vector sum
I3

of the 3 phase currents (fig. 1).

DE55338

Irsd
The residual current is equal to three times the zero-sequence current I0.
I1 Ir sd = 3 • I0 = I1 + I 2 + I3

Detection of the fault current

Fig. 1. Definition of
I2 residual current.
Earth-fault current can be detected in a number of ways.
Measurement Accuracy Recommended Assembly
sensors minimum threshold
for earth-fault
protection

+++
Neutral
Special core A few amperes
51G 51G

balance CT
DE57339

DE57340EN
Irsd Irsd

Direct measurement by special core It can also be installed on the accessible

balance CT connected directly to the neutral to earth link. The result is high
protection relay. The CT is installed measurement accuracy; a very low
around the live conductors and directly detection threshold (a few amperes)
creates the residual current. can be used.

++
Neutral
Toroidal CT + 10% of InCT (DT)
interposing ring 5% of InCT (IDMT)
DE57341EN

51G DE57342EN 51G

CT 1฀or฀5฀A 1฀or฀5฀A

Irsd Irsd

Differential measurement using a classic The toroidal CT can also be installed on

toroidal CT installed around the live the accessible neutral to earth link with
conductors and generating the residual an interposing ring CT.
current, plus an interposing ring CT used This solution offers good accuracy and
as an adapter for the protection relay. flexibility in CT selection.

3 phase CTs + ++ 10% of InCT (DT) 51N

interposing ring 5% of InCT (IDMT)
I1
DE57343EN

CT Measurement of the currents in the three

I2 1฀or฀5฀A

I3 phases with one CT per phase and

measurement of the residual current
by a special interposing ring CT.
Irsd
Practically speaking, the residual-current threshold must be:
b Is0 Š 10% InCT (DT protection),
b Is0 Š 5% InCT (IDMT protection).

3 phase CTs + No H2 restraint I1 51N

(Irsd calculated 30% InCT (DT)
DE57344

by relay) 10% InCT (IDMT)

I2
I3
With H2 restraint
10% InCT (DT)
5% InCT (IDMT)
Calculation based on measurement of the currents in the three phases with one CT
per phase.
b The residual current is calculated by the protection relay.
b Measurement accuracy is not high (sum of CT errors and saturation characteristics,
calculated current).
b Installation is easier than in the previous case, but measurement accuracy is lower.
Practically speaking, the protection threshold settings must comply with the
following rules:
b Is0 Š 30% InCT for DT protection (10% InCT for a protection relay with H2 restraint),
b Is0 Š 10% InCT for IDMT protection.

22
 Sensors Voltage transformers (VT) 0

The role of a voltage transformer is to provide Measurement of phase-to-phase voltages

its secondary winding with a voltage The voltage transformer is made up of two windings, the primary and the secondary,
proportional to that applied to the primary coupled by a magnetic circuit, and connections can be made between phases or
between a phase and earth.
circuit. Voltage transformers are used
for both measurements and protection. Voltage transformers are characterized by the following values:
(publications IEC 60186, IEC 60044-2 and NFC 42-501) (1)
b power frequency, generally 50 or 60 Hz,
b highest primary voltage in the power system,
b rated secondary voltage 100, 100/3, 110, 110/3 volts depending on the type
of connection,
b rated voltage factor used to define the heat-rise characteristics,
b apparent power, in VA, that the voltage transformer can supply to the secondary,
without causing errors exceeding its accuracy class, when connected to the rated
primary voltage and to its rated load. Note that a VT must never be short-circuited
on the secondary, because the power supplied increases and the transformer
can be damaged by the resulting heat rise,
b accuracy class defining the guaranteed error limits for the voltage ratio and phase-
displacement under the specified power and voltage conditions.

A number of measurement assemblies are possible:

DE57345

b 3-transformer star assembly (fig. 1)

(requires 1 insulated high-voltage terminal per transformer)

Transformation ratio: ------------------- for example

Un ⁄ 3
100 ⁄ 3

b 2-transformer “V” assembly, (fig. 2)

(requires 2 insulated high-voltage terminals per transformer)
Fig. 1. Star-connected voltage transformers (VT).

Transformation ratio: Un ⁄ 100 for example

In isolated neutral systems, all phase-neutral VTs sufficiently loaded to avoid the risk
DE57346

of ferromagnetic resonance.
(1) Elements related to the type of assembly, characteristics of the site (e.g. temperature), etc.
must also be taken into account.

Fig. 2. V-connected voltage transformers (VT).

Measurement of residual voltage
The residual voltage characterizing the neutral-point voltage with respect to earth
V3 is equal to the vector sum of the 3 phase-to-earth voltages.
The residual voltage is equal to three times the zero-sequence voltage V0:
DE55347

Vrsd = 3 • V0 = V1 + V2 + V3 (fig. 3)
Vrsd
V1 The occurrence of this voltage signals the existence of an earth fault.
It can be measured or calculated:
b measurement using three voltage transformers whose primaries are star connected
V2 and the secondaries, in an open delta arrangement, supply the residual voltage (fig. 4),
b calculation by the relay, using three voltage transformers whose primaries and
secondaries are star connected (fig. 5).
Fig. 3. Definition of residual voltage.
DE57348

DE57349

59N V1 59N

V2
Vrsd
V3

Fig. 4. Direct measurement of residual Fig. 5. Calculation of residual voltage.

voltage.

23
 Protection functions General characteristics 0

The protection relays that continuously Operation

monitor power system variables include The relay includes (fig. 1):
combinations of basic functions to suit b analog measurement input for the variable observed, received from the sensor,
b logic result of measurement processing (noted S),
b instantaneous logic output of the protection function, used for indication,
the power system components being
monitored. for example (noted Si),
b delayed logic output of the protection function, used to control circuit breaker
tripping (noted St).

Characteristics (fig. 2)
The protection function work mode involves characteristic times (IEC 60255-3):
DE57270

b operating time: this is the time between the application of the characteristic quantity
I S 0 St (at twice the threshold setting) and the switching of the output relay (instantaneous
output),
I฀>฀Is
Si
b overshoot time: this is the difference between operating time and the maximum
time during which the characteristic quantity can be applied with no tripping,
Fig. 1. Relay operating principle. b reset time: this is the time between a sudden decrease in the characteristic quantity
(example of ANSI 51 phase overcurrent protection relay) and the switching of the output relay.
Note: other non-standardized terms are commonly found as well, the definitions of which may
vary from one manufacturer to another: reclaim time, no response time, instantaneous tripping
time, memory time.

To improve stability, the functions have a drop out/pick up ratio d that is a %

of the threshold setting: in the example in figure 3, S goes from 1 to 0 when I = d • Is
I฀rms
DE55272EN

2฀Is

Threshold
฀Is t

Si Operating฀time Reset฀time

t
0

I Overshoot฀time
2฀Is

Is
t

Maximum฀no฀trip฀time฀

Fig. 2. Protection function characteristic times.

I
DE55271

Is

d฀•฀Is
t

t
0

Fig. 3. Drop out/pick up ratio.

24
Protection functions General characteristics 0

Settings
Some protection functions may be set by the user, in particular:
b tripping set point: it sets the limit of the observed quantity that actuates
the protection function.
b tripping time:
v definite time delay (DT)
The example in figure 1, applied to a current relay, shows that above the current
threshold Is, the protection tripping time is constant (time delay setting T).
t Current฀threshold

DE55273EN
No Delayed
operation operation

T
Delay
I
Is

Fig. 1. Definite time tripping principle.

v IDMT delay (IDMT: Inverse Definite Minimum Time)

The example in figure 2, applied to a current relay, shows that above the current
threshold Is, the higher the current, the shorter the protection tripping time.
t Current฀threshold
DE55274EN

No Delayed
operation operation

T
Delay
I
Is 10฀•฀Is

Fig. 2. IDMT tripping principle.

There are several types of curves, determined by equations and defined by the
various standardization organizations: for example, the IEC defines the following
(fig. 3):
- standard inverse time (SIT),
- very inverse time (VIT),
- extremely inverse time (EIT).
t
DE55275

EIT

VIT

SIT

I
Is 10฀•฀Is
Fig. 3. IDMT tripping curves.

b timer hold: adjustable reset time,

b restraint: inhibition of tripping according to percentage of second harmonic,
b time constants (e.g. thermal overload ANSI 49RMS),
b characteristic angle (e.g. directional overcurrent ANSI 67).

25
Protection functions List of functions 0

The main protection functions are listed with a brief definition in the table below.
They are listed in numerical order by ANSI C37.2 code.

ANSI code Name of function Definition

12 Overspeed Detection of rotating machine overspeed
14 Underspeed Detection of rotating machine underspeed
21 Distance protection Impedance measurement detection
21B Underimpedance Back-up phase-to-phase short-circuit protection for generators
24 Flux control Overfluxing check
25 Synchro-check Check before paralleling two parts of the power system
26 Thermostat Protection against overloads
27 Undervoltage Protection for control of voltage sags
27D Positive sequence undervoltage Protection of motors against operation with insufficient voltage
27R Remanent undervoltage Check on the disappearance of voltage sustained by rotating machines
after the power supply is disconnected
27TN Third harmonic undervoltage Detection of stator winding insulation earth faults (impedant neutral)
32P Directional active overpower Protection against active overpower transfer
32Q Directional reactive overpower Protection against reactive overpower transfer
37 Phase undercurrent 3-phase protection against undercurrent
37P Directional active underpower Protection against active underpower transfer
37Q Directional reactive underpower Protection against reactive underpower transfer
38 Bearing temperature monitoring Protection against overheating of rotating machine bearings
40 Field loss Protection of synchronous machines against faults or field loss
46 Negative sequence / unbalance Protection against unbalanced phase current
47 Negative sequence overvoltage Negative sequence voltage protection and detection of reverse rotation of rotating machines
48 - 51LR Excessive starting time and locked rotor Protection of motors against starting with overloads or reduced voltage, and for loads
that can block
49 Thermal overload Protection against overloads
49T RTDs Protection against overheating of machine windings
50 Instantaneous phase overcurrent 3-phase protection against short-circuits
50BF Breaker failure Checking and protection if the circuit breaker fails to trip after a tripping order
50N or 50G Instantaneous earth fault Protection against earth faults:
50N: residual current calculated or measured by 3 CTs
50G: residual current measured directly by a single sensor (CT or core balance CT)
50V Instantaneous voltage-restrained phase 3-phase protection against short-circuits with voltage-dependent threshold
overcurrent
50/27 Inadvertent generator energization Detection of inadvertent generator energization
51 Delayed phase overcurrent 3-phase protection against overloads and short-circuits
51N or 51G Delayed earth fault Protection against earth faults:
51N: residual current calculated or measured by 3 CTs
51G: residual current measured directly by a single sensor (CT or core balance CT)
51V Delayed voltage-restrained phase overcurrent 3-phase protection against short-circuits with voltage-dependent threshold
59 Overvoltage Protection against excessive voltage or sufficient voltage detection
59N Neutral voltage displacement Insulation fault protection
63 Pressure Detection of transformer internal faults (gas, pressure)
64REF Restricted earth fault differential Earth fault protection for star-connected 3-phase windings with earthed neutral
64G 100% generator stator earth fault Detection of stator winding insulation earth faults (impedant neutral power systems)
66 Successive starts Protection function that monitors the number of motor starts
67 Directional phase overcurrent 3-phase short-circuit protection according to current flow direction
67N/67NC Directional earth fault Earth fault protection depending on current flow direction
(NC: Neutral compensated)
78 Vector shift Vector shift disconnection protection
78PS Pole slip Detection of loss of synchronization of synchronous machines
79 Recloser Automated device that recloses the circuit breaker after transient line fault tripping
81H Overfrequency Protection against abnormally high frequency
81L Underfrequency Protection against abnormally low frequency
81R Rate of change of frequency (ROCOF) Protection for fast disconnection of two parts of the power system
87B Busbar differential 3-phase protection against busbar internal faults
87G Generator differential 3-phase protection against internal faults in AC generators
87L Line differential 3-phase protection against line internal faults
87M Motor differential 3-phase protection against internal faults in motors
87T Transformer differential 3-phase protection against internal faults in transformers

26
Protection functions Associated functions 0

The protection functions are completed Switchgear control

by the following: This function controls the different types of switchgear closing and tripping coils.

Trip circuit supervision

b additional control functions,
b operation monitoring functions,
b operation functions, This function indicates switchgear trip circuit failures.

Control logic
b indication functions,
b metering functions,
b diagnosis functions, This function is used to implement logic discrimination by the sending and/or reception
of “blocking signals” by different protection units.
b communication functions,
for enhanced operation of power systems.
Logic functions
These functions perform logic equation operations to generate additional data
All of these functions may be provided
by the same digital protection unit. or orders used for the application.

Operation functions
These functions make operation more convenient for the user.
b Transformer on-load tap changers,
b Reactive energy regulation,
b Fault locator (ANSI 21FL),
b Capacitor bank control,
b Remaining operating time before thermal overload tripping.

Metering functions
These functions provide information required for a good understanding
of power system operation.
b Phase current,
b Tripping current,
b Residual current,
b Differential and through currents,
b Current THD (total harmonic distortion),
b Phase-to-neutral and phase-to-phase voltages,
b positive sequence, negative sequence and residual voltages,
b Voltage THD (total harmonic distortion),
b Frequency,
b Active, reactive and apparent power,
b Power factor (cos j),
b Active and reactive energy,
b Peak demand current, active and reactive power,
b Temperature,
b Motor starting time,
b Disturbance recording.

Switchgear diagnosis functions

b Switchgear closing and fault tripping operation counters,
b Operation time,
b Charging time,
b Sensor supervision (VT, CT); this function monitors the voltage or current
transformer measurement chain and acts on the related protection functions,
b Cumulative breaking current (kA2).

Communication functions
These functions are used for the exchange of available data by the different power
system components (measurements, states, control orders…).

27
 Discrimination Time-based discrimination 0

Protection functions form a consistent Principle

system depending on the overall structure of Time-based discrimination consists of assigning different time delays to the overcurrent
the power distribution system and the neutral protection units distributed through the power system.
The closer the relay is to the source, the longer the time delay.
earthing arrangement. They should therefore
Operating mode
be viewed as a system based on the principle
The fault shown in the diagram opposite (fig. 1) is detected by all the protection units
of discrimination, which consists of isolating
the faulty part of the power system and only (at A, B, C, and D). The contacts of delayed protection unit D close faster than those
that part as quickly as possible, leaving all of protection unit C, which themselves close faster than those of protection unit B…
the fault-free parts of the power system Once circuit breaker D tripped and the fault current has been cleared, protection units
A, B and C, which are no longer required, return to the stand-by position.
The difference in operation time DT between two successive protection units
energized.
Various means can be used to implement is the discrimination interval. It takes into account (fig. 2):
discrimination in power system protection: b breaking time Tc of the downstream circuit breaker, which includes the breaker
b time-based discrimination, response time and the arcing time,
b time delay tolerances dT,
b upstream protection unit overshoot time: tr,
b current-based discrimination,
b discrimination by data exchange, referred b a safety margin m.
to as logic discrimination, ΔT should therefore satisfy the relation:
b discrimination by the use of directional ΔT Š Tc + tr + 2dT + m
protection functions, Considering present switchgear and relay performances, ΔT is assigned a value
b discrimination by the use of differential of 0.3 s.
protection functions, Example: Tc = 95 ms, dT = 25 ms, t r = 55 ms; for a 300 ms discrimination interval,
b combined discrimination to ensure better the safety margin is 100 ms.
overall performance (technical and economic), TB TA
DE55242EN

or back-up.

dTB TcB m trA dTA

DE57241EN

Discrimination฀interval฀∆T

Fig. 2. Breakdown of a discrimination interval.

Advantages
51 TA฀=฀1.1฀s
A

This discrimination system has two advantages:

b it provides its own back-up; for example if protection unit D fails,
protection unit C is activated ΔT later,
51 TB฀=฀0.8฀s b it is simple.
B

Drawbacks
However, when there are a large number of cascading relays, since the protection
unit located the furthest upstream has the longest time delay, the fault clearing time
becomes prohibitive and incompatible with equipment short-circuit current withstand
51 TC฀=฀0.5฀s
C
and external operating necessities (e.g. constraint imposed by utility).

51 TD฀=฀0.2฀s
D

Phase-to-phase฀fault

Fig. 1. Time-based discrimination principle.

28
 Discrimination Time-based discrimination 0

Application
This principle is used in radial power systems. (fig. 1)
The time delays set for time-based discrimination are activated when the current
DE57243

exceeds the relay settings. The settings must be consistent.

51 IsA,฀TA
There are two cases, according to the type of time delay used.
A
Definite time relays (fig. 2)
The conditions to be fulfilled are: I sA > I sB > I sC et TA > TB > TC.
The discrimination interval ΔT is conventionally in the range of 0.3 seconds.
51 IsB,฀TB
B t C B A

DE55244EN

51 IsC,฀TC
C TA
∆T
TB
∆T
TC
Fig. 1. Radial power system with time-based discrimination.
I
IsC IsB IsA IscC IscB IscA
max max max

Fig. 2. Time-based discrimination with definite time relays.

IDMT relays (fig. 3)

If the thresholds are set to the rated current In, overload protection is ensured
at the same time as short-circuit protection and setting consistency is guaranteed.
I nA > I nB > I nC
I sA = I nA, l sB = I nB, and I sC = I nC
The time delays are set to obtain the discrimination interval ΔT for the maximum
current seen by the downstream protection relay. The same family of curves is used
to avoid overlapping in a portion of the domain.

t C B A
DE55245

∆T

∆T

I
IsC IsB IsA IscC IscB IscA
max max max

Fig. 3. Time-based discrimination with IDMT relays.

29
 Discrimination Current-based discrimination 0

Principle
Current-based discrimination uses the principle that within a power system,
the further the fault is from the source, the weaker the fault current is.

Operating mode
A current protection unit is installed at the starting point of each section: the
threshold is set to a value lower than the minimum short-circuit current caused by a
fault in
the monitored section, and higher than the maximum current caused by a fault
downstream (outside the monitored area).

Advantages
With these settings, each protection device is only activated by faults located
immediately downstream, within the monitored zone, and is not sensitive to faults
outside that zone.
For sections of lines separated by a transformer, it can be of benefit to use this system
since it is simple, cost-effective and quick (tripping with no delay).
An example is given below (fig.1):
IscBmax < IsA < IscAmin
IsA = current setting
IscB on the transformer primary is proportional to the maximum short-circuit current
on the secondary.
Time delays TA and TB are independent, and TA may be shorter than TB.

Drawbacks
The upstream protection unit (A) does not provide back-up for the downstream
protection unit (B).
In practice, it is difficult to define the settings for two cascading protection units, and
still ensure satisfactory discrimination, when there is no notable decrease in current
between two adjacent areas. This is the case in medium voltage power systems,
except for sections with transformers.

Application
The following example concerns current protection of a transformer between
two cable sections.
The overcurrent protection setting I s satisfies the relation:
1.25 I scBmax < IsA < 0.8 I scAmin
Discrimination between the two protection units is ensured.

t B A
DE57246EN

IscAmin IscBmax

51 IsA,฀TA 51 IsA,฀TA TB
A A

TA

I
IsB IscB IsA IscA
max min

Discrimination฀curves

51 IsB,฀TB
B

Condition Condition
IsA฀<฀IscAmin IsA฀>฀IscBmax

Fig. 1. Current-based discrimination operation.

30
 Discrimination Logic discrimination 0

Principle
This system was developed to solve the drawbacks of time-based discrimination.
This principle is used when short fault clearing time is required (fig. 1).
DE57247EN

Operating mode
The exchange of logic data between successive protection units eliminates the need
for discrimination intervals, and thereby considerably reduces the tripping time of the
circuit breakers closest to the source.
51 In radial power systems, the protection units located upstream from the fault are
activated; those downstream are not. The fault point and the circuit breaker to be
tripped can therefore be clearly located.
Each protection unit activated by a fault sends:
b a blocking signal to the upstream level (an order to increase the upstream relay
time delay),
b a tripping order to the related circuit breaker unless it has already received a
51

blocking signal from the downstream level.

Blocking฀signal Time-delayed tripping is provided as back-up.
The principle is illustrated in figure 2:
51 b when a fault appears downstream from B, the protection unit at B blocks
the protection unit at A,
b only the protection unit at B triggers tripping after the delay TB, provided it has not
received a blocking signal,
b the duration of the blocking signal for the protection unit at A is limited to TB + T3,
with T3 Š opening and arc extinction time of circuit breaker B (typically 200 ms),
b if circuit breaker B fails to trip, protection unit A gives a tripping order at TB + T3,
51

Phase-to-phase b when a fault appears between A and B, protection unit A trips after the delay TA.
fault

Advantages
Fig. 1. Logic discrimination principle. Tripping time is not related to the location of the fault within the discrimination chain
or to the number of protection units in the chain.
This means that discrimination is possible between an upstream protection unit
with a short time delay and a downstream unit with a long time delay. For example,
a shorter time delay may be used at the source than near the loads.
DE57248EN

The system also has back-up designed into it.

Drawbacks
Since logic signals must be transmitted between the different levels of protection
TA
IsA
units, extra wiring must be installed. This can be a considerable constraint when
A inst.

the protection units are far apart each other, in the case of long links, for example
(several hundreds of meters long).
This difficulty may be bypassed by combining functions: logic discrimination
Blocking฀signal
in the nearby switchboards and time-based discrimination between zones
that are far apart (refer to chapter on combined logic + time-based discrimination).

Application
TB฀+฀T3
(back-up)
TB
This principle is often used to protect medium voltage power systems that include
IsB
inst.
radial branches with several levels of discrimination.
B

Fig. 2. Logic discrimination operation.

31
 Discrimination Directional protection
discrimination 0

Principle
In a looped power system, in which faults are fed from both ends, it is necessary
to use a protection unit that is sensitive to the direction of the flow of fault current
in order to locate and clear the fault selectively. This is the role of directional
Cable
DE57249EN

overcurrent protection units.

Operating mode
67 Is,฀T The protection actions differ according to the direction of the current (figs. 1 and 2),
i.e. according to the phase displacement of the current in relation to a reference given
by the voltage vector; the relay therefore needs both current and voltage data.
I

The operating conditions, namely the position of the tripping and no tripping zones,
Vref are adapted to fit the power system to be protected (fig. 3).
Example of the use of directional protection units (fig. 4):
Circuit breakers D1 and D2 are equipped with directional protection units
that are activated if the current flows from the busbars to the cable.
Busbar
Directional protection principle If a fault occurs at point 1, it is only detected by the protection unit at D1.
The protection unit at D2 does not detect it, because of the detected current direction.
Fig. 1. Protection unit active.

The D1 circuit breaker trips.

If a fault occurs at point 2, it is not detected by these protection units
and the D1 and D2 circuit breakers remain closed.
DE57250EN

Other protection units must be included to protect the busbars.

Cable

Advantage
The solution is simple and may be used in a large number of cases.
67 Is,฀T
I

Drawback
Vref Voltage transformers must be used to provide a phase reference to determine
the direction of the current.

Application
Busbar

This principle is used to protect parallel incomers and closed loop power systems
Directional protection principle and also for certain cases of earth fault protection.
Fig. 2. Protection unit not active.

Tripping฀zone Cable Cable

DE57252EN
DE55251EN

I฀busbars฀V฀cable
No฀tripping฀zone
Vref 1
67 67

Vref
I฀cable฀V฀busbars D1 D2

Busbars
2
Directional protection principle Directional protection
Fig. 3. Detection of current direction. Fig. 4. Example of two parallel incomers.

32
 Discrimination Differential protection
discrimination 0

Principle
These protection units compare the current at the two ends of the monitored section
of the power system (fig. 1).
DE57253EN

A Operating mode
Any amplitude or phase difference between the currents indicates the presence
IA of a fault: The protection units only react to faults within the area they cover and
are insensitive to any faults outside that area. This type of protection is therefore
selective by nature.
Instantaneous tripping takes place when IA-IB ≠ 0
In order for differential protection to work, it is necessary to use current transformers
Protected
87
zone
specifically sized to make the protection units insensitive to other phenomena.
What makes differential protection units stable is that they do not pick up as long as
there are no faults in the zone being protected, even if a differential current is detected:
b transformer magnetizing current,
IB

b line capacitive current,

B b error current due to saturation of the current sensors.
There are two main principles according to the stabilization mode:
b high impedance differential protection: the relay is series-connected to a stabilization
Fig. 1. Differential protection principle.

resistor Rs in the differential circuit (figs. 2 and 3),

b percentage-based differential protection: the relay is connected independently to
the circuits carrying the currents IA and IB. The difference between the currents IA
and IB is determined in the protection unit and the protection stability is obtained by
a restraint related to the through current (figs. 4 and 5).
IA IB I฀differential
Protected Constant฀threshold
DE57254EN

DE55256EN

zone Is

Rs I฀through

∆I

Fig. 2. High impedance differential protection diagram. Fig. 3. Stability by resistance.

IA IB I฀differential
Protected
DE57255EN

DE55257EN

zone
Threshold฀%฀It

Is
∆I/I I฀through

Fig. 4. Percentage-based differential protection diagram. Fig. 5. Stability by restraint.

Advantages
b Protection sensitive to fault current less than the rated current of the protected
equipment.
b Zone protection that can trip instantaneously.

Drawbacks
b The cost of the installation is high.
b It takes skill to implement the system.
b An overcurrent back-up function needs to be included.

Comparison of the two principles

b High impedance differential protection:
v the upstream and downstream CTs must have the same rated currents (primary
and secondary),
v the resistance of the stabilization resistor is chosen to avoid tripping by external
faults with a saturated CT and to allow the relay to be supplied by the CT,
v The relay is relatively simple, but requires the use of stabilization resistors.
b Percentage-based differential protection:
v can be adapted to fit the equipment to be protected,
v the relay is relatively more complicated, but is easy to use.

Application
Differential protection may concern all priority high power components:
motors, generators, transformers, busbars, cables and lines.

33
 Discrimination Combined discrimination 0

Combined discrimination is a combination of Several practical examples of applications using combined

basic discrimination functions that provides discrimination are given below:
additional advantages in comparison to b current-based + time-based,
individual types of discrimination. b logic + time-based,
b total discrimination, b time-based + directional,
b redundancy or back-up. b logic + directional,
b differential + time-based.

Current-based + time-based discrimination

The example shows an arrangement with both of the following:
DE57258EN

b current-based discrimination between A1 and B,

b time-based discrimination between A2 and B.
This provides total discrimination, and the protection unit at A provides back-up
for the protection unit at B.
51 IsA1,฀TA1
A 51 IsA2,฀TA2
t B A
DE55259EN

Protected
zone

TA2
∆T
TB
51 IsB,฀TB
B TA1
I
Fig. 1. Current-based + time-based discrimination.
IsB IsA2 IscB IsA1 IscA

Logic + back-up time-based discrimination

The example shows an arrangement with both of the following:
DE57260

b logic discrimination between A1 and B,

b time-based discrimination between A2 and B.
IsA,฀TA1 IsA,฀TA2 The A2 protection unit provides back-up for the A1 protection unit, if A1 fails to trip
51 51 due to a blocking signal fault (permanent blocking signal).
A
t B A
DE55261EN

TA2
∆T
TB
TB
IsB TA1
B T=0
I
Fig. 2. Logic + back-up time-based discrimination. IsB IsA IscB IscA

Logic + time-based discrimination

The example shows an arrangement with both of the following:
DE57262EN

Combined Time-based b logic discrimination inside a switchboard

discrimination discrimination (between A and B and between C and D).
51 0.1฀s 1.3฀s b time-based discrimination between two switchboards B and D, with TB = TD + ΔT.
A It is not necessary to install a logic signal transmission link between two switchboards
that are far apart. The tripping delays are shorter than with time-based discrimination
alone (fig. 3).
b back-up time-based discrimination needs to be included at points A and C
51 0.7฀s 1.0฀s (refer to the paragraph above).
B

51 0.1฀s 0.7฀s
C

51 0.4฀s 0.4฀s
D
Fig. 3. Comparison of combined (logic + time-based)
discrimination and time-based discrimination tripping times.

34
 Discrimination Combined discrimination 0

Time-based + directional discrimination

D1 and D2 are equipped with short time-delayed directional protection units;
H1 and H2 are equipped with time-delayed overcurrent protection units.
If a fault occurs at point 1, it is only detected by the D1 (directional), H1 and H2
DE57263

protection units. The protection unit at D2 does not detect it, because of the detected
H1 H2 current direction. D1 trips. The H2 protection unit drops out, H1 trips and the faulty
section H1-D1 is isolated.
TH1 = TH2
51 51
TD1 = TD2
TH = TD + ΔT

1
67 67

D1 D2

Fig. 1. Time-based + directional discrimination.

51 BSIG 51
Logic + directional discrimination
The example shows that the orientation of blocking signals depends on the direction
DE57264EN

of the current flow.

This principle is used for busbar coupling and closed loops.
D1 67 D2

Fault at D2 end:
b tripping at D2 and B,
Vref

b D1 is blocked by B (BSIG: blocking signal).

B

Fault at D1 end:
51 BSIG 51

b tripping at D1 and B,
D1 67 D2
b D2 is blocked by B (BSIG: blocking signal).

Vref

Fig. 2. Logic + directional discrimination.

Differential + time-based discrimination

The example shows an arrangement with both of the following:
b instantaneous differential protection,
DE57265EN

b a phase overcurrent or earth fault protection unit at A as back-up for the differential
protection unit,
b a current protection unit at B to protect the downstream zone,
51 IsA,฀TA
A
b time-based discrimination between the protection units at A and B, with
TA = TB + ΔT.
This provides back-up for the differential protection function, but double-wound
Protected current transformers are sometimes necessary.
Note: time-based discrimination may be replaced by logic discrimination.
zone 87

51 IsB,฀TB
B

Fig. 3. Differential + time-based discrimination.

35
 Power-system protection Single-incomer power systems 0

Power-system protection should: Phase-to-phase faults (fig. 1)

b detect faults, The incomer and feeders are equipped with phase overcurrent protection units
b isolate the faulty parts of the power system, (ANSI 51).
Time-based discrimination is used between the incomer protection unit (A)
and the feeder protection units (D).
keeping the fault-free parts in operation.
The protection unit at D detects fault 1 on the feeder and trips circuit breaker D
Protection units are chosen according to
the power-system configuration (parallel after a delay TD.
operation of generators or transformers, The protection unit at A detects fault 2 on the busbars and trips after a delay TA.
loop or radial power system, neutral It also acts as back-up should protection D fail.
Choose: IsA Š IsD and TA Š TD + ΔT
ΔT: discrimination interval (generally 0.3 s).
earthing arrangement…).
Consideration must be given to: The protection unit at D must be selective in relation to the downstream protection units:
b phase-to-phase fault protection, if the delay required for protection A is too long, logic or combined (logic + time-based)
b earth fault protection, linked to the neutral discrimination should be used.

Phase-to-earth faults
earthing arrangement.
The following types of systems will be
examined: single-incomer, dual-incomer, Resistance earthing on the transformer (fig.2)
Earth fault protection units (ANSI 51N) are installed on the feeders, incomer and
neutral earthing connection.
open loops and closed loops.
Time-based discrimination is used between the different protection units.
These units are necessarily different from phase fault protection units since the fault
currents are in a different range.
The feeder protection units are set selectively in relation to the incomer protection
unit, which is itself set selectively in relation to the neutral earthing protection unit
(in accordance with discrimination intervals).
The fault current flows through the capacitances of the fault-free feeders
and the earthing resistance.
All the fault-free feeder sensors detect capacitive current.
To prevent inadvertent tripping, the protection unit on each feeder is set higher than
the feeder’s capacitive current.
b fault at 3: the D1 circuit breaker is tripped by the protection unit linked to it,
b fault at 4: the A circuit breaker is tripped by the incomer protection unit,
b fault at 5: the protection unit on the neutral earthing connection trips circuit breaker H
on the transformer primary circuit. (fig. 1).
The protection unit at D must be selective in relation to the downstream protection units:
if the delay required for protection A is too long, logic discrimination should be used.
The neutral earthing protection unit at H acts as back-up should the incomer
protection unit at A fail to trip.
The incomer protection unit at A acts as back-up should a feeder protection unit
at D fail to trip.
DE57230

DE57231EN

H
t D A 51G t D A H

TH
5 ∆T
51 IsA,฀TA
TA 51G TA
∆T ∆T
A
TD A TD
I I

2 IsD IsA IsD IsA IsH

D 4 D3 D2 D1 I฀fault

51 IsD,฀TD
51G 51G 51G

1 3
Capacitive฀current
Resistive฀current
Fig. 1. Phase-to-phase fault protection. Fig. 2. Phase-to-earth fault protection (resistance-earthed neutral at transformer).

36
 Power-system protection Single-incomer power systems 0

Phase-to-earth faults (cont’d)

Resistance-earthed neutral at busbars (fig. 1)
A zero sequence generator is used for resistance-earthing.
Earth fault protection units (ANSI 51G) are installed on the feeders, incomer and zero
H
DE57232

sequence generator.
Time-based discrimination is used between the different protection units.
The feeder protection units and incomer protection unit are set selectively in relation
3 to the earthing impedance protection unit. As in the previous case, the protection
unit on each feeder is set higher than the feeder’s capacitive current.
51G IsA,฀TA
In the event of a fault on feeder 1, only the D1 feeder circuit breaker trips.
In the event of fault on the busbars 2, only the protection unit on the earthing
connection detects the fault. It trips circuit breaker A.
A
In the event of fault on the transformer secondary circuit 3, the incomer protection
units detects the fault. It trips circuit breaker H.
2 Note: when circuit breaker A is open, the transformer secondary circuit neutral
is isolated. It may be necessary to protect it by a neutral voltage displacement
D2 D1

51G 51G IsD,฀TD 51G

measurement (ANSI 59N).
The zero sequence generator protection unit acts as back-up should the incomer
protection unit at A or a feeder protection unit at D fail to trip.
If the condition IsD > 1.3 Ic cannot be satisfied for a feeder, a directional earth fault
1 protection unit may be used to discriminate between fault current and capacitive
current.

Reactance-earthed neutral
Fig. 1. Phase-to-earth fault protection The same procedure is used as for resistance-earthing at the transformer or busbars.
(resistance-earthed neutral at busbars).
Isolated neutral (fig. 2)
A fault, regardless of its location, produces current which flows through the capacitance
of the fault-free feeders.
In industrial power systems, this current is generally weak (a few amperes), allowing
DE57233EN

operations to carry on while the fault is being tracked.

Time-based discrimination is used between the different protection units.
The fault is detected by an insulation monitoring device or a neutral voltage
displacement protection unit (ANSI 59N).
When the total capacitive current of a power system is high (in the range of ten
amperes), additional measures must be taken to quickly clear the fault.
IMD

Directional earth fault protection can be used to selectively trip the fault feeder.
59N

Solidly earthed neutral

This is similar to resistance-earthing at the transformer, but the capacitive currents
are negligible compared to the fault current, so the protection function is simpler
to implement.

Compensated neutral
The power system is earthed at the transformer. Faults are detected by a specific
directional earth fault protection unit (ANSI 67NC), which monitors the active
residual current and recognizes faults during their initial transient phase.

Fig. 2. Phase-to-earth fault protection (isolated neutral).

37
 Power-system protection Dual-incomer power systems 0

Phase-to-phase faults (fig. 1)

Power system with two transformer incomers or two line incomers
The feeders are equipped with phase overcurrent protection units with delays set
to TD.
DE57234

H1 H2
51 TH 51 TH The two incomers A1 and A2 are equipped with phase overcurrent protection units
(ANSI 51) set selectively in relation to the feeders, i.e.
TA Š TD + ΔT.
T1 T2 They are also equipped with directional protection units (ANSI 67) with delays set
at TR < TA – ΔT.
Time-based discrimination is used between the incomer A protection units
and feeder D protection units.
3
Current-based discrimination is used between the power supply H protection units
and incomer A protection units.
67 TR 67 TR

This means that a fault at 1 is cleared by the tripping of D2 after a delay TD.
51 TA 51 TA

A fault at 2 is cleared by the tripping of A1 and A2 with a delay of TA (the directional

protection units do not detect the fault).
A1 A2

A fault at 3 is detected by the A1 directional protection unit which trips at the time TR,
2 allowing continued operation of the fault-free part of the power system.
D1 D2 However, the fault at 3 is still fed by T1. At the time TH Š TA + ΔT,
H1 is tripped by the phase overcurrent protection unit linked to it.
51 TD 51 TD

Phase-to-earth faults (fig. 2)

1 Resistance-earthed neutral at incomer transformers
Earth fault protection units (ANSI 51G) are installed on the feeders and set higher
Fig. 1. Phase-to-phase fault protection. than the corresponding capacitive currents, with delays of TD.
Directional earth fault protection units (ANSI 67N) are installed on incomers A1 and
A2, with time delays of TR.
Earth fault protection units (ANSI 51G) are installed on the earthing connections and
DE57235

H1 H2 set higher than the incomer and feeder protection units, with time delays such that
51G TN 51G TN TN Š TD + ΔT.
Time-based discrimination is used between the different protection units.
This means that a fault at 4 is cleared by the tripping of D1.
A fault at 5 is cleared by the tripping of A1, A2, H1 and H2 by the protection units
located on the neutral earthing connections of the 2 transformers.
A fault at 6 is detected by the A1 directional protection unit which trips at the time TR,
6
allowing continued operation of the fault-free part of the power system.
However, the fault at 6 continues to be supplied up to the time TN at which
67N TR 67N TR

the protection unit on the corresponding transformer earthing connection trips

the H1 circuit breaker.
A1 A2

5 Resistance-earthed neutral at the busbars

A zero sequence generator is used for resistance-earthing.
Earth fault protection units are installed on the feeders, incomers and zero sequence
generator.
D1 D2 D3

51G TD 51G TD 51G TD Time-based discrimination is used between the different protection units.
The system operates in the same way as in single-incomer power systems.

Isolated neutral
4
The system operates in the same way as in single-incomer power systems.

Fig. 2. Phase-to-earth fault protection (resistance-earthed Solidly earthed neutral

This is similar to resistance-earthing, but the phase-to-earth current is higher
neutral at the transformer).

and reaches the phase-to-phase current level.

Compensated neutral
Only one earthing coil is in service at a given time to ensure power system
capacitance matching; this is similar to single-incomer power systems.

38
 Power-system protection Dual-incomer power systems 0

Additional protection functions

Coupling (fig. 1)
G The synchro-check function (ANSI 25) is used to check that the circuits to be connected
have voltage amplitude, phase and frequency differences within acceptable limits
DE57236

to allow closing of the coupling circuit breaker.

Decoupling
When electrical installations are supplied by the utility and an independent power
source, interference between the two sources as a result of events such as a utility
failure or earth faults should be avoided. The consequences include voltage and
frequency fluctuations and current and power exchanges between the different circuits.
Protection functions are often advocated or imposed in the distributors’ technical
guides.
There are several methods of decoupling two sources:
b monitoring of the active power direction and protection by a reverse power
protection relay (ANSI 32P),
b monitoring of voltage amplitude and under or overvoltage protection
(ANSI 27 or 59),
25 b monitoring of frequencies and underfrequency (ANSI 81L) or overfrequency
(ANSI 81H) protection,
b protection against phase shifts caused by faults (ANSI 78),
Fig. 1. Power system coupling protection.

b monitoring of frequency variations and ROCOF (rate of change of frequency)

protection (ANSI 81R) with respect to a threshold. This protection function is faster
than the frequency protection functions and more stable than phase shift protection.

Automatic source transfer (fig. 2)

The system in figure 2 shows an installation with two busbars normally supplied
Source฀1 Source฀2
DE57237EN

27 59 by two sources with the coupling open (2/3 configuration).

If source 1 is lost, the power system is reconfigured. Source 1 is opened and
50 the coupling is closed; this automatic source transfer takes place according
50N to a procedure:
b initialization of the transfer by the detection of undervoltage (ANSI 27) on source 1
resulting in opening of the source 1 circuit breaker: Us = 70% Un,
C฀➞฀O C
O฀➞฀C
b inhibition of transfer if a fault is detected downstream from source 1 by an overcurrent
protection unit (ANSI 50 and 50N),
b enabling of transfer after the disappearance of voltage sustained by rotating machines
is checked by the remanent undervoltage protection unit (ANSI 27R):
M Us = 25% Un,
27R b enabling of transfer after verification that there is sufficient voltage (ANSI 59)
Fig. 2. Automatic source transfer. on source 2 and closing of coupling circuit breaker: Us = 85% Un.

39
Power-system protection Open loop power systems 0

In distribution systems that include The power system is operated as an open loop and protection is provided at the ends
of the loops, which are equipped with circuit breakers (fig. 1).
The switching devices used on the substations are switches.
substations supplied in open loops,
protection is provided at the head Faults cause power outages.
of the loop. Phase overcurrent and earth fault protection units (ANSI 51 and 51N) are installed
on the circuit breakers at the head of each loop.
A fault occurring in a cable that connects 2 substations may trip either of these circuit
breakers depending on the position of the loop opening.
The protection is often completed by an automated device that:
b clears the fault (with the power off) by opening the devices located at the ends
of the faulty cable, after the faulty cable has been located by the fault detector,
b closes the circuit breaker that has tripped at the head of the loop,
b closes the device that ensured the normal opening of the loop in order to restore
power to the fault-free downstream half of the loop.
The power system can be put back into its initial operating state after the faulty circuit
has been repaired.
The outage may last from a few seconds to a few minutes depending on whether
the loop is reconfigured automatically or manually.
DE57238EN

51 51
51N 51N

C C

C C

C C

C C

O C

Fig. 1. Open loop protection principle.

40
Power-system protection Closed loop power systems 0

In distribution systems that include The power system may be operated in closed loops, with each section protected by
circuit breakers at the ends of the section. Most faults do not cause power outages.
Various protection solutions may be used.
substations supplied in closed loops,
protection is provided for different sections.
Differential protection (fig. 1)
Each cable is equipped with a line differential protection unit (ANSI 87L) and each
substation is equipped with a busbar differential protection unit (ANSI 87B).
This type of protection is very quick.
If the neutral is resistance-earthed, the sensitivity of the differential protection units
must cover phase-to-earth faults.

DE57239EN
C C

87L 87L

C C
87B 87B

C C

Fig. 1. Closed loop differential protection.

Overcurrent protection and directional logic discrimination (fig. 2)

The circuit breakers in the loop are equipped with overcurrent and directional
protection units. Logic discrimination is used to clear faults as quickly as possible.
A fault in the loop activates:
b all the protection units if the loop is closed,
b all the protection units upstream from the fault when the loop is open.
Each protection unit sends a blocking signal to one of the adjacent units in the loop,
according to the data transmitted by the directional protection unit.
Protection units that do not receive a blocking signal trip with a minimum delay that
is not dependent on the fault’s position in the loop:
b the fault is cleared by two circuit breakers, one on either side of the fault if the loop
is closed, and all the switchboards remain energized,
b the fault is cleared by the upstream circuit breaker if the loop is open.
This solution is a comprehensive one since it protects cables and busbars.
It is fast, selective and includes back-up protection.
DE57240

51 51
51N 51N

67 67 67 67
67N 67N 67N 67N

67 67 67 67
67N 67N 67N 67N

Fig. 2. Loop overcurrent protection and directional logic discrimination.

41
 Busbar protection Types of faults and
protection functions 0

Busbars are electrical power dispatching Phase-to-phase and phase-to-earth faults

nodes that generally have more than
two ends. Overcurrent protection
The use of time-based discrimination with the overcurrent (ANSI 51) and earth fault
(ANSI 51N) protection functions may quickly result in excessive fault clearing time
Specific busbar protection may be provided
in a variety of ways, using basic functions. due to the number of levels of discrimination.
In the example (fig. 1), protection unit B trips in 0.4 s when there is a busbar fault
at point 1; when a busbar fault occurs at point 2, protection unit A trips in 0.7 s,
since the discrimination interval is set to 0.3 s.
The use of logic discrimination (fig. 2) with overcurrent protection provides a simple
solution for busbar protection.
A fault at point 3 is detected by protection unit B, which sends a blocking signal
51
51N TA฀=฀0.7฀s
DE57281EN

A
to protection unit A.
Protection unit B trips after 0.4 s.
However, a fault at point 4 is only detected by protection unit A, which trips after 0.1 s;
2 with backup protection provided if necessary in 0.7 s.

Differential protection
51
51N TB฀=฀0.4฀s
Differential protection (ANSI 87B) is based on the vector sum of the current entering
B and leaving the busbars for each phase. When the busbars are fault-free, the sum
1 is equal to zero, but when there is a fault on the busbars, the sum is not zero and
the busbar supply circuit breakers are tripped.
This type of protection is sensitive, fast and selective.
51 b With percentage-based, low impedance differential protection, the difference
is calculated directly in the relay. The threshold setting is proportional to the through
C 51N TC฀=฀0.1฀s

current and CTs with different ratios may be used. However, the system becomes
Fig. 1. Time-based discrimination. complicated when the number of inputs increases.
b With high impedance differential protection (fig. 3), the difference is calculated
TA1฀=฀0.1฀s TA2฀=฀0.7฀s in the cables, and a stabilization resistor is installed in the differential circuit. The CTs
51 51 are sized to account for saturation according to a rule given by the protection relay
DE57282EN

A manufacturer. The threshold setting is approximately 0.5 CT In and it is necessary to

use CTs with the same ratings.

51 TB฀=฀0.4฀s
B

51 TC฀=฀0.1฀s
C

Fig. 2. Logic discrimination.

DE57283

Rs
51 87B

51 51 51

Fig. 3. Differential protection.

42
Busbar protection Types of faults and
protection functions
0

Load shedding function

The load shedding function is used when a shortage of available power in comparison
to the load demand causes an abnormal drop in voltage and frequency:
certain consumer loads are disconnected according to a preset scenario,
called a load shedding plan, in order to recover the required power balance.
Different load shedding criteria may be chosen:
b undervoltage (ANSI 27),
b underfrequency (ANSI 81L),
b rate of change of frequency (ANSI 81R).

Breaker failure
The breaker failure function (ANSI 50BF) provides backup when a faulty breaker
fails to trip after it has been sent a trip order: the adjacent incoming circuit breakers
are tripped.
The example (fig. 1) shows that when a fault occurs at point 1 and the breaker
that has been sent the trip order fails, the breaker failure protection function is faster
than action by upstream protection time-based discrimination: 0.6 s instead of 0.7 s.

51 0.7฀s 51 0.7฀s
DE57284EN

Faulty฀
breaker

51 50BF 51 50BF 51 50BF

0.4฀s 0.2฀s

Fig. 1. Breaker failure.

43
Link (line and cable) Types of faults and
protection protection functions 0

The term “link” refers to components designed Thermal overload

to convey electrical power between two points Protection against overheating due to overload currents in conductors under steady
that are several meters to several kilometers state conditions is provided by the thermal overload protection function (ANSI 49RMS),
which estimates temperature buildup according to the current measurement.
apart: links are generally overhead lines with
Phase-to-phase short circuits
bare conductors or cables with insulated
conductors.
b Phase overcurrent protection (ANSI 51) may be used to clear the fault,
A specific type of protection is required the time delay being set to provide discrimination.
for links. A distant 2-phase fault creates a low level of overcurrent and an unbalance;
a negative sequence / unbalance protection function (ANSI 46) is used to complete
the basic protection function (fig. 1).
b To reduce fault clearance time, a percentage-based differential protection function
(ANSI 87L) may be used. It is activated when the differential current is equal to more
than a certain percentage of the through current. There is a relay at either end
of the link and information is exchanged by the relays via a pilot (fig. 2).
DE57285EN

DE57286
46
51 87L
51N฀or฀67N

87L

Fig. 1. Link protection Fig. 2. Link protection

by overcurrent relay. by differential relays.

Phase-to-earth short circuits

Time-delayed overcurrent protection (ANSI 51N) may be used to clear faults with
a high degree of accuracy (fig. 1).
For long feeders though, with high capacitive current, the directional earth fault
protection function (ANSI 67N) allows the current threshold to be set lower than the
capacitive current in the cable as long as system earthing is via a resistive neutral.

44
 Link (line and cable) Types of faults and
protection protection functions 0

Distance protection
Distance protection (ANSI 21) against faults affecting line or cable sections is used
in meshed power systems (parallel links, several sources).
It is selective and fast, without requiring time-based discrimination. Sensitivity
DE57279EN

depends on the short-circuit power and the load. It is difficult to implement when the
21 type of link is not the same throughout (overhead line + cable).
It operates according to the following principle:
b measurement of an impedance proportional to the distance from the measurement
A point to the fault,
b delimitation of impedance zones which represent line sections of different lengths
(fig.1),
b tripping by zone with time delay.
The example in figure 2 shows the following for the protection unit at point A in line
0% 21

section AB:
b an impedance circle at 80% of the length of the line (zone 1), inside which tripping
is instantaneous,
b an impedance band between 80% and 120% of the length of the line (zone 2),
in which tripping is delayed (200 ms),
b an impedance circle at 120% of the length of the line (zone 3), outside which
there is long-time delayed backup tripping of protection unit B outside AB,
b an impedance circle at 120% downstream to provide backup for downstream
protection,
b When there is communication between the protection units at the ends,
Zone฀1 tripping can take place instantaneously between 0 and 100%.
X ZL
DE55280EN

Zone฀3

T3
Zone฀2

T2
Zone฀1
T1 Load฀Z

R
80%

Zone฀2 Downstream฀zone

21

B
100%
Fig. 2. Impedance circles.

21
Recloser
The recloser function (ANSI 79) is designed to clear transient and semi-permanent
faults on overhead lines and limit down time as much as possible. The recloser
function automatically generates circuit breaker reclosing orders to resupply
Zone฀2

overhead lines after a fault. This is done in several steps:

b tripping when the fault appears to de-energize the circuit,
b time delay required for insulation recovery in the location of the fault,
120%

b resupply of the circuit by reclosing.

Reclosing is activated by the link protection units.
The recloser may be single-phase and/or 3-phase, and may comprise one or more
Zone฀3 consecutive reclosing cycles.

L
Fig. 1. Distance protection principle.

45
 Transformer protection Types of faults 0

The transformer is a particularly important The main faults that can affect transformers are:
b overloads,
b short-circuits,
power system component.
Transformers requires effective protection b frame faults.
against all faults liable to damage them,
whether of internal or external origin. Overloads
The choice of a protection unit is often Overloads may be caused by an increase in the number of loads supplied
based on technical and cost considerations simultaneously or by an increase in the power drawn by one or more loads.
related to the power rating. Overloads result in overcurrent of long duration, causing a rise in temperature that is
detrimental to the preservation of insulation and to the service life of the transformer.

Short-circuits
Short-circuits can occur inside or outside the transformer.
Internal short-circuits: faults between different phase conductors or faults
between turns of the same winding. The fault arc damages the transformer winding
and can cause fire. In oil transformers, the arc causes the emission of
decomposition gas.
If the fault is slight, a small amount of gas is emitted and the accumulation of gas
can become dangerous.
A violent short-circuit can cause major damage liable to destroy the winding and also
the tank frame by the spread of burning oil.
External short-circuits: phase-to-phase faults in the downstream connections.
The downstream short-circuit current creates electrodynamic stress in the transformer
that is liable to have a mechanical effect on the windings and lead to an internal fault.

Frame faults
I I
Imax Imax
DE55288EN

Frame faults are internal faults. They may occur between the winding and the tank
frame or between the winding and the magnetic core.
Imax
They cause gas emission in oil transformers. Like internal short-circuits, they can cause
transformer damage and fire. The amplitude of the fault current depends on the
2
upstream and downstream neutral earthing arrangements, and also on the position
% % of the fault in the winding:
0 100% 0 50% 100% b in star connected arrangements (fig.1), the frame fault current varies between 0
and the maximum value depending on whether the fault is at the neutral or phase
end of the winding.
b in delta connected arrangements (fig. 2), the frame current varies between 50 and
100% of the maximum value depending on whether the fault is in the middle or at the
end of the winding.

Information on transformer operation

Fig.฀1 Fig.฀2

Transformer energizing (fig. 3)

Fault current according to the position of the fault in the

Transformer energizing creates a transient peak inrush current that may reach 20
winding.

times the rated current with time constants of 0.1 to 0.7 seconds. This phenomenon
is due to saturation of the magnetic circuit which produces a high magnetizing
Ic

current. The peak current is at its highest when energizing takes place as the voltage
–t
DE55289

-----

goes through zero and there is maximum remanent induction on the same phase.
ˆ • ( t) = Ie
ie ˆ • eτ e

The waveform contains a substantial amount of 2nd harmonics.

This phenomenon is part of normal power system operation and should not
be detected as a fault by the protection units, which should let the peak energizing
current through.
Overfluxing
Transformer operation at a voltage or frequency that is too low creates excessive
magnetizing current and leads to deformation of the current by a substantial amount
t

of 5th harmonics.

Fig. 3. Transformer energizing.

Ie: inrush current envelope
τe: time constant

46
 Transformer protection Protection functions 0

Overloads
Overcurrent of long duration may be detected by a definite time or IDMT delayed
overcurrent protection unit (ANSI 51) that provides discrimination with respect
to the secondary protection units.
DE57290

The dielectric temperature is monitored (ANSI 26) for transformers with liquid
insulation and the winding temperature is monitored (ANSI 49T) for dry type
transformers.
87T Thermal overload protection (ANSI 49RMS) is used for more sensitive monitoring
of temperature rise: heat rise is determined by simulation of the release of heat
according to the current and thermal inertia of the transformer.
For MV/LV transformers, overloads may be detected on the low voltage side
by the long time trip function of the main LV circuit breaker.

Short-circuits
Several protection functions may be implemented.
Fig. 1. Transformer differential protection.

b For oil transformers, devices that are sensitive to gas emission or oil movement
t

(ANSI 63) caused by short-circuits between turns of the same phase or phase-to-phase
DE57291EN

51
51 short-circuits:
50 50 v Buchholz relays for free breathing HV/HV transformers,
v gas and pressure detectors for hermetically sealed HV/LV transformers.
b Transformer differential protection (ANSI 87T) (fig.1) which provides fast protection
against phase-to-phase faults. It is sensitive and used for vital high power transformers.
I

Transformer฀energizing Max.฀LV฀ Max.฀HV฀ To avoid nuisance tripping, the 2nd harmonic of the differential current is measured
curve Isc Isc to detect transformer energizing (H2 restraint) and the 5th harmonic is measured
to detect overfluxing (H5 restraint).
Fig. 2. Transformer overcurrent protection. The use of this protection function with neural network technology provides
the advantages of simple setting and stability.
b An instantaneous overcurrent protection unit (ANSI 50) (fig. 2) linked to the circuit
breaker located on the transformer primary circuit provides protection against violent
DE57292

short-circuits. The current threshold is set higher than the current due to short-circuits
on the secondary winding, thereby ensuring current-based discrimination.
51G b HV fuses can be used to protect transformers with low kVA ratings.

Frame faults
b Tank frame fault (fig. 3)
Fig. 3. Transformer tank frame fault protection. This slightly delayed overcurrent protection unit (ANSI 51G), installed on the
transformer frame earthing connection (if the setting is compatible with the neutral
earthing arrangement), is a simple, effective solution for internal winding-to-frame
faults. In order for it to be used, the transformer must be isolated from the earth.
DE57293

This protection function is selective: it is only sensitive to transformer frame faults

on the primary and secondary sides.
Another solution consists of using earth fault protection:
51N 64REF

b earth fault protection (ANSI 51N) located on the upstream power system for frame
faults that affect the transformer primary circuit.
b earth fault protection (ANSI 51N) located on the incomer of the switchboard being
supplied, if the neutral of the downstream power system is earthed on the busbars
(fig. 4).
These protection functions are selective: they are only sensitive to phase-to-earth
faults situated in the transformer or on the upstream and downstream connections.
b restricted earth fault protection (ANSI 64REF) if the downstream power system
Fig. 4. Earth fault protection. Fig. 5. Restricted earth fault neutral is earthed at the transformer (fig. 5). This is a differential protection function
protection. that detects the difference between residual currents measured at the neutral
earthing point and at the three-phase output of the transformer.
b neutral point earth protection (ANSI 51G) if the downstream power system is
earthed at the transformer (fig. 6).
DE57294

b neutral voltage displacement protection (ANSI 59N) may be used if the downstream
power system neutral is isolated from the earth (fig. 7).
59N

51G

Fig. 6. Neutral point earth Fig. 7. Neutral voltage

protection. displacement protection.

47
Transformer protection Recommended settings 0

Faults Appropriate protection function ANSI code Setting information

Overloads
Dielectric temperature monitoring 26 Alarm at 95°C; tripping at 100°C
(transformers with liquid insulation)
Winding temperature monitoring 49T Alarm at 150°C; tripping at 160°C
(dry type transformers)
Thermal overload 49 RMS Alarm threshold = 100% of thermal capacity used
Tripping threshold = 120% of thermal capacity used
Time constant in the 10 to 30 minute range
Low voltage circuit breaker Threshold Š In
Short-circuits
Fuses Choice of rating according to appropriate method for switchgear concerned
Instantaneous overcurrent 50 High threshold > downstream Isc
Definite time overcurrent 51 Low threshold < 5 In
Delay Š downstream T + 0.3 seconds
IDMT overcurrent 51 IDMT low threshold, selective with downstream, approximately 3 In
Percentage-based differential 87T Slope = 15% + setting range
Min. threshold 30%
Buchholz or gas and pressure detection 63 logic
Earth faults
Tank frame overcurrent 51G Threshold > 20 A, delay 0.1 seconds
Earth fault 51N/51G Threshold ð 20 % of maximum earth fault current and > 10% of CT rating
(with 3CTs and H2 restraint)
Delay 0.1 seconds if earthing is on the power system
Time delay according to discrimination if earthing is on the transformer
Restricted earth fault differential 64REF Threshold 10% of In, no delay
Neutral point earth fault 51G Threshold < permanent limitation resistance current
Neutral voltage displacement 59N Threshold approximately 10% of residual overvoltage
Overfluxing
Flux control 24 Threshold > 1.05 Un/fn
Delay: constant time, 1 hour

48
Transformer protection Examples of applications 0

DE57295

DE57296
51G 49RMS
26 50
26 51
63 63 51G฀(2฀x)

Low rated HV/LV transformer High-rated HV/LV transformer

Fuse protection Circuit breaker protection
DE57297

DE57298
49RMS 49RMS
50 26 50
26 51 63 51
63 51N 49T 51G฀(2฀x)
51G฀(2฀x) 64REF
87T

Low-rated HV/HV transformer High-rated HV/HV transformer

49
Motor protection Types of faults 0

Motors are the interface between electrical Motors are affected by:
b faults related to the driven loads,
b power supply faults,
and mechanical equipment. They are
connected to the machines they drive b motor internal faults.
and are therefore exposed to the same
environment. Faults related to the driven loads
Motors may be subjected to internal Overloads
mechanical stress due to their moving parts. If the power drawn is greater than the rated power, there is overcurrent in the motor
A single faulty motor can disrupt an entire and an increase in losses, causing a rise in temperature.
Excessive starting time and frequency of starts
Motor starting creates substantial overcurrents which are only admissible for short
production process. Modern motors have
optimized characteristics which make them durations. If a motor starts too frequently or if starting takes too long due to insufficient
unsuitable for operation other than according motor torque compared to load torque, overheating is inevitable and must be avoided.
to their rated characteristics. This means Blocking
Rotation suddenly stops due to blocking of the driven mechanism. The motor draws
the starting current and stays blocked at zero speed. There is no more ventilation and
that they are relatively fragile electrical loads
that need to be carefully protected. overheating occurs very quickly.
There are asynchronous motors (mainly Loss of load
squirrel-cage motors or wound-rotor motors) Loss of pump priming or a break in load coupling causes no-load operation of the motor,
which does not directly harm the motor. However, the pump itself is quickly damaged.
and synchronous motors (motors with DC
Power supply faults
rotor excitation).
Loss of supply
Questions concerning synchronous motors
are the same as those that concern This causes motors to operate as generators when the inertia of the driven load
asynchronous motors plus those that is high.
concern generators. Voltage sag
This reduces motor torque and speed: the slow-down causes increased current
and losses. Abnormal overheating therefore occurs.
Unbalance
3-phase power supply may be unbalanced for the following reasons:
b the power source (transformer or AC generator) does not supply symmetrical
3-phase voltage,
b all the other consumers together do not constitute a symmetrical load and
this unbalances the power supply system,
b the motor is powered by two phases after a fuse has blown on one phase,
b The phase order is reversed, changing the direction of motor rotation.
Power supply unbalance creates negative sequence current which causes very high
losses and quick rotor overheating.
When the voltage is re-supplied after a motor power failure, the motor sustains
remanent voltage that may lead to overcurrent when the motor starts again or even
a mechanical break in transmission.

Motor internal faults

Phase-to-phase short-circuits
These faults vary in strength according to where they occur in the coil and they cause
serious damage.
Stator frame fault
The amplitude of the fault current depends on the power system neutral earthing
arrangement and the position of the fault within the coil.
Phase-to-phase short-circuits and stator frame faults require motor rewinding,
and frame faults can also irreparably damage the magnetic circuit.
Rotor frame faults (for wound-rotor motors)
Rotor insulation breakdown can cause a short-circuit between turns and produce
a current that creates local overheating.
Overheating of bearings due to wear or faulty lubrication.
Field loss
This fault affects synchronous motors; motor operation is asynchronous and the rotor
undergoes considerable overheating since it is not designed accordingly.
Pole slip
This fault also affects synchronous motors, which may lose synchronism for different
reasons:
b mechanical: sudden load variation,
b electrical: power supply system fault or field loss.

50
Motor protection Protection functions 0

Overloads
Overloads may be monitored the following:
b IDMT overcurrent protection (ANSI 51),
b thermal overload protection (ANSI 49RMS), which involves overheating
due to current,
b RTD temperature monitoring (ANSI 49T).

Excessive starting time and locked rotor

The same function provides both types of protection (ANSI 48-51LR).
For excessive starting time protection, an instantaneous current threshold is set
below the value of the starting current and activated after a delay that begins when
the motor is energized; the delay is set longer than the normal starting time.
Locked rotor protection is activated outside starting periods by current above
a threshold, after a delay.

Successive starts
The successive starts protection function (ANSI 66) is based on the number of starts
within a given interval of time or on the time between starts.

Loss of pump priming

This is detected by a definite time undercurrent protection unit (ANSI 37)
which is reset when the current is nil (when the motor stops).

Speed variation
Additional protection may be provided by the direct measurement of rotation speed
by mechanical detection on the machine shaft.
The underspeed protection function (ANSI 14) detects slow-downs or zero speed
resulting from mechanical overloads or locked rotors.
The overspeed protection function (ANSI 12) detects racing when the motor is
driven by the load, or a loss of synchronization for synchronous motors.

Loss of supply
Loss of supply is detected by a directional active power protection unit (ANSI 32P).

Voltage sag
This is monitored by a delayed positive sequence undervoltage protection unit
(ANSI 27D).
The voltage threshold and delay are set to allow discrimination with the power
system’s short-circuit protection units and to tolerate normal voltage sags such as
those that occur during motor starting. The same protection function may be shared
by several motors in the switchboard.

Unbalance
Protection is provided by the detection of negative sequence current by an IDMT
or definite time protection unit (ANSI 46).
The phase rotation direction is detected by the measurement of negative sequence
overvoltage (ANSI 47).

Resupply
Motor remanence is detected by a remanent undervoltage protection unit (ANSI 27R)
which enables resupply when the voltage drops below a certain voltage threshold.

51
 Motor protection Protection functions 0

Phase-to-phase short circuits

They are detected by a delayed overcurrent protection unit (ANSI 50 and 51).
The current threshold is set higher than the starting current and a very short delay
is applied to prevent the protection unit from tripping on transient inrush currents.
DE57300

When the corresponding breaking device is a contactor, it is associated with fuses

which ensure short-circuit protection.
For large motors, a high impedance or percentage-based differential protection
system (ANSI 87M) is used (fig.1).
As an alternative, by appropriate adaptation of the connections on the neutral side
and by the use of 3 summing current transformers, a simple overcurrent protection
unit (ANSI 51) can be used to provide sensitive, stable detection of internal faults (fig.2).
87M

Stator frame fault

The type of protection depends on the neutral earthing arrangement. High sensitivity
is required to limit damage to the magnetic circuit.
If the neutral is solidly earthed or impedance-earthed, a delayed residual overcurrent
protection unit (ANSI 51N/51G) may be used to protect the main windings.
In isolated neutral arrangements, a neutral voltage displacement protection unit
(ANSI 59N) may be used to detect neutral voltage displacement. If the motor feeder
Fig. 1. Phase-to-phase short-circuit.
is capacitive (long cable), a directional earth fault protection unit (ANSI 67N) is used.
Differential protection (ANSI 87M)

Rotor frame fault

DE57301

An insulation monitoring device with AC or DC current injection detects winding

insulation faults.

Overheating of bearings
The bearing temperature is measured by RTDs (ANSI 38).

Field loss
51 For synchronous motors: refer to the chapter on generators.

Pole slip
For synchronous motors: refer to the chapter on generators.

Fig. 2. Phase-to-phase short-circuit.

Autodifferential overcurrent protection (ANSI 51)

52
Motor protection Recommended settings 0

Faults Appropriate protection function ANSI code Setting information

Faults related to the driven loads
Overloads IDMT overcurrent 50/51 Setting that enables starting
Thermal overload 49RMS According to motor operating characteristics
(time constant in the range of 10 to 20 minutes)
RTDs 49T Depends on the thermal class of the motor
Excessive Delayed current threshold 48 Threshold in the 2.5 In range
starting time Delay: starting time + a few seconds
Locked rotor Delayed current threshold 51LR Threshold: 2.5 In
Delay: 0.5 to 1 second
Successive Counting of number of starts 66 According to motor manufacturer
starts
Loss of load Phase undercurrent 37 Threshold in the range of 70% of drawn current
Delay: 1 second
Speed variation Mechanical detection of overspeed, 12, 14 Threshold ± 5% of rated speed
underspeed Delay of a few seconds
Power supply faults
Loss of supply Directional active overpower 32P Threshold 5% of Sn
Delay: 1 second
Voltage sag Positive sequence undervoltage 27D Threshold from 0.75 to 0.80 Un
Delay in the 1 second range
Unbalance Negative sequence / unbalance 46 b Definite time
Is1 = 20% In, delay = starting time + a few seconds
Is2 = 40% In, delay 0.5 seconds
b IDMT
Is = 10% In, tripping time at 0.3 In > starting time
Rotation Phase rotation direction 47 Negative sequence voltage threshold at 40% of Un
direction
Resupply Remanent undervoltage 27R Threshold < 20 to 25% of Un
Delay in the 0.1 second range
Internal motor faults
Phase-to-phase Fuses Rating that allows consecutive starts
short circuits Definite time overcurrent 50/51 Threshold > 1.2 starting I, delay in the 0.1 second range (DT)
Differential protection 87M Slope 50%, threshold 5 to 15% of In, no delay
Stator frame Earthed Earth fault 51N/51G 10% of maximum earth fault current
fault neutral Delay in the 0.1 second range (DT)
Isolated Power system with 59N Threshold = 30% of Vn
neutral low capacitance
Neutral voltage displacement
High capacitance 67N Minimum threshold according to sensor
Directional earth fault
Rotor frame Insulation monitoring device
fault
Overheating of Temperature measurement 38 According to manufacturer’s instructions
bearings
Specific synchronous motor faults
Field loss Directional reactive overpower 32Q Threshold 30% of Sn
Delay: 1 second
Underimpedance 40 Same as for generator
Pole slip Loss of synchronization 78PS Same as for generator

53
Motor protection Examples of applications 0

DE57302

DE57303
37 27D
46 27R
48฀-฀51LR 46
49RMS 48฀-฀51LR
51G 49RMS
66 51
51G
M M 66
67N

Asynchronous motor controlled by fuse Asynchronous motor controlled by circuit

and contactor breaker
Example: 100 kW pump Example: 250 kW fan
DE57304

DE57305
12 27D
14 27R
27D 32P
27R 32Q
46 40
48฀-฀51LR 46
49RMS 48฀-฀51LR
26 51 49RMS
63 51G 51
49T 66 51G
87T 66
78PS
87M
38/ 38/
M 49T M 49T

Motor-transformer unit: asynchronous Priority synchronous motor

motor/transformer Example: 2 MW compressor
Example: 1 MW crusher

54
 Generator protection Types of faults 0

Generator operation can be altered by both Faults such as overloads, unbalance and internal phase-to-phase faults are the same
type for generators and motors.
Only faults specifically related to generators are described below.
faults within the machine and disturbances
occurring in the power system to which
it is connected. External phase-to-phase short-circuits
A generator protection system therefore When a short circuit occurs in a power system close to a generator, the fault current
has a dual objective: to protect the machine looks like the current shown in figure 1.
and protect the power system. The maximum short-circuit current should be calculated taking into account
the machine’s substransient impedance X”d.
The short-circuit current detected by a protection unit with a very short time delay
The generators referred to here are
synchronous machines (AC generators). (about 100 ms) should be calculated taking into account the machine’s transient
impedance X’d.
The short-circuit current in steady state conditions should be calculated taking into
account the synchronous impedance X.
It is low, generally less than the generator’s rated current.
Voltage regulators can often keep it higher than the rated current (2 or 3 times higher)
for a few seconds.

Internal phase-to-frame faults

This is the same type of fault as for motors and the effects depend on the neutral
earthing arrangement used. There is a difference however in comparison to motors
in that generators can be decoupled from the power system during start-up and
shutdown and also in test or stand-by mode. The neutral earthing arrangement
Current
may differ according to whether the generator is connected or disconnected
DE55306EN

and the protection functions should be suitable for both cases.

Subtransient Transient
phenomena phenomena

Field loss
When a generator coupled with a power system loses its field, it becomes
desynchronized with respect to the power system. It then operates asynchronously,
t at a slight overspeed, and it draws reactive power.
This causes stator overheating since the reactive current may be high and rotor
overheating since the rotor is not sized for the induced currents.

Loss of synchronism
Fig. 1. Short circuit currents across generator terminals.

The loss of generator synchronization occurs when balanced steady state operation
is disrupted by strong disturbances: for example, when a short-circuit in the power
system causes a drop in the electrical power supplied by the generator and
the generator accelerates, still driven by the prime mover.

Operation as a motor
When a generator is driven like a motor by the power system (to which it is connected),
it applies mechanical energy to the shaft and this can cause wear and damage
to the prime mover.

Voltage and frequency variations

Voltage and frequency variations under steady state conditions are due to regulator
malfunctions and cause the following problems:
b frequencies that are too high cause motor overheating,
b frequencies that are too low cause motor power loss,
b frequency variations cause motor speed variations, that may cause mechanical
damage and malfunctioning of electronic devices,
b voltage that is too high puts stress on the insulation of all parts of the power system,
causes magnetic circuit overheating and damages sensitive loads,
b voltages that are too low cause torque loss and an increase in current and motor
overheating,
b voltage fluctuations cause motor torque variations resulting in flicker (flickering of
light sources).

Generator management
Normal generator management may be disturbed:
b inadvertent energization when the normal starting sequence is not complied with:
the generator, shut down but coupled to the power system, runs like a motor and may
damage the prime mover,
b power management: when there are several parallel sources, the number of
sources must be adapted to suit the power drawn by the loads; there is also the case
of islanded operation of an installation with its own power generation.

55
 Generator protection Protection functions 0

Overloads
The overload protection functions for generators are the same as those for motors:
b IDMT overcurrent (ANSI 51),
b thermal overload (ANSI 49RMS),
b RTD temperature monitoring (ANSI 49T).

Unbalance
Protection is ensured, the same as for motors, by IDMT or definite time negative
sequence current detection (ANSI 46).

External phase-to-phase short-circuits

(in the power system)
Tripping฀threshold
DE55307EN

b As the value of short-circuit current decreases over time to approximately the rated
Is

current, if not lower, in steady state conditions, simple current detection may be
insufficient.
This type of fault can be detected effectively by a voltage-restrained overcurrent
protection device (ANSI 51V), the threshold of which increases with the voltage (fig.1).
0.2฀Is Operation is delayed.
b When the machine is equipped with a system that maintains the short-circuit at
U
0.3฀Un Un about 3 In, the use of a phase overcurrent protection unit (ANSI 51) is recommended.
b Another solution consists of using a delayed underimpedance protection unit (ANSI
Fig. 1. Voltage restrained overcurrent protection threshold. 21G), which may also provide back-up (ANSI 21B) for the overcurrent protection unit.

Internal phase-to-phase short-circuits (in the stator)

b High impedance or percentage-based differential protection (ANSI 87G) provides
a sensitive, quick solution.
b If the generator is operating in parallel with another source, a directional phase
overcurrent protection unit (ANSI 67) can detect internal faults.
b In certain cases, particularly for generators with low power ratings compared to the
power system to which they are connected , internal phase-to-phase short-circuit
DE57308

50
A
protection may be provided as follows (fig. 2):
G v instantaneous overcurrent protection (A), validated when the generator circuit
breaker is open, with current sensors on the neutral point side, set lower than
the rated current,
50 v instantaneous overcurrent protection (B), with current sensors on the circuit breaker
B
side, set higher than the generator short-circuit current.

Stator frame fault

b If the neutral is earthed at the generator neutral point, earth fault protection
(ANSI 51G) or restricted earth fault protection (ANSI 64REF) is used.
b If the neutral is earthed within the power system rather than at the generator neutral
Fig. 2. AC generator coupled with other sources.
point, a stator frame fault is detected by:
v an earth fault protection unit on the generator circuit breaker when the generator is
coupled to the power system,
v by an insulation monitoring device for isolated neutral arrangements when
the generator is decoupled from the power system.
b If the neutral is impedant at the generator neutral point, 100% stator frame fault
protection (ANSI 64G) is used. This protection combines two functions:
v neutral voltage displacement, which protects 80% of the windings (ANSI 59N)
v third harmonic (H3) neutral point undervoltage, which protects the 20%
of the windings on the neutral side (ANSI 27TN).
b If the neutral is isolated, frame fault protection is provided by an insulation
monitoring device. This device operates either by detecting residual voltage
(ANSI 59N) or by injecting DC current between the neutral and earth. If this device
exists on the power system, it monitors the generator when it is coupled; a special
generator device, validated by the open position of the generator circuit breaker
being in the open position, is needed to monitor insulation when the generator
is uncoupled.

Rotor frame fault

When the excitation current circuit is accessible, frame faults are monitored
by an insulation monitoring device.

56
 Generator protection Protection functions 0

Field loss
Field loss is detected either by a delayed reactive overpower protection unit
(ANSI 32Q) for high power rating systems or by an underimpedance protection unit
(ANSI 40) for “islanded” power systems with generators, or by direct monitoring
of the excitation circuit if it is accessible (ANSI 40DC).

Loss of synchronization
Protection against the loss of synchronization is provided by a specific pole slip
protection function (ANSI 78PS) ; the pole slip measurement principle is based on
either an estimate of machine instability according to the equal-area criterion,
or by the detection of active power swings (fig. 1); an overspeed protection unit
(ANSI 12) may be used as back-up.
Without฀loss฀of฀synchronization
5 7 57
4
DE55310EN

Active฀power 4 6 Active฀power 6
A2฀=฀A1 A3 A2฀=฀A1
8 8
Mechanical
power 1 1
(excluding฀
losses) 9 9

A1 A1

2 3 2 3
Time Internal฀angle
With฀loss฀of฀synchronization
Active฀power
Active฀power
4 A2 4
10 10
Mechanical 11 A2
power 5 1 5 11
1
(excluding฀
losses) 9 9
A1 A1
6 6
2 3 2 3
Time Internal฀angle
1 2 appearance฀of฀fault฀
3 4 clearing฀of฀fault 7 7
4 11 power฀swings 8 8

Fig. 1. Active power flows in a generator following a short-circuit.

Operation as a motor
This is detected by a relay that detects reverse active power (ANSI 32P) drawn
by the generator.

Voltage and frequency variations

Voltage variations are monitored by an overvoltage-undervoltage protection unit
(ANSI 59 and 27) and frequency variations by an overfrequency-underfrequency
protection unit (ANSI 81H and 81L).
The protection units are delayed since the phenomena do not require instantaneous
action and because the power system protection units and voltage and speed
controllers must be allowed time to react.
The flux control function (ANSI 24) can detect overfluxing.

G Inadvertent energization
The starting of generators according to a normal sequence is monitored by the
DE57309

inadvertent energization protection function (ANSI 50/27). This protection involves

the simultaneous use of:
37P b an instantaneous overcurrent function and an undervoltage protection function,
b the undervoltage protection function is delayed to avoid unwanted 3-phase fault
tripping, and there is another delay to allow generator starting without the presence
of current before coupling.

Power management
The distribution of active power flows can be managed appropriately by the use of
directional active underpower protection units (ANSI 37P), which provide adequate
Fig. 2. Independent operation of an installation with its own control of source and load circuit breaker tripping (example in fig. 2).
generating unit.

57
Generator protection Recommended settings 0

Faults Appropriate protection function ANSI code Setting information

Prime mover related faults
Overloads Overcurrent 51 In threshold, IDMT curve
Thermal overload 49RMS According to the generator operating characteristics:
maximum thermal capacity used 115 to 120%
RTDs 49T Depends on the thermal class of the generator
Operation Directional active overpower 32P Threshold 5% of Sn (turbine) to 20% of Sn (diesel)
as a motor Delay of a few seconds
Speed variation Mechanical detection of overspeed, 12, 14 Threshold ± 5% of rated speed
underspeed Delay of a few seconds
Power supply system faults
External With current Overcurrent 51 Threshold 2 In
short-circuits maintained at 3 In Delay for discrimination with downstream protection
Without current Voltage-restrained 51V Threshold 1.2 In
maintained at 3 In overcurrent Delay for discrimination with downstream protection
Underimpedance 21B About 0.3 Zn
(back-up) Delay for discrimination with downstream protection
Inadvertent Inadvertent energization 50/27 Current threshold = 10% of generator In
energization Voltage threshold = 80% of Un
Inhibit time after voltage sag = 5 seconds
Minimum current appearance time after voltage appearance = 250 ms
Generator internal faults and generator control
Phase-to-phase High impedance differential 87G Threshold 5 to 15% of In
short circuits No delay
Percentage-based differential 87G Slope 50%, threshold 5 to 15% of In
No delay
Directional phase overcurrent 67 Threshold In
Delay according to discrimination with the other sources
Unbalance Negative sequence / unbalance 46 Threshold 15% of In
Delay of a few seconds
Stator frame If neutral Earth fault 51G Threshold = 10% of maximum earth fault current
fault is earthed at Delay for discrimination with downstream protection
generator stator Restricted earth fault 64REF Threshold 10% of In
differential No delay
If neutral 100% stator frame fault 64G/59N Vrsd threshold = 30% of Vn
is impedant at Delay of 5 seconds
generator stator 64G/27TN Adaptive threshold = 15% of 3rd harmonic Vrsd
If neutral Earth fault on generator 51N/51G Threshold 10 to 20% of maximum earth fault current
is earthed within circuit breaker side Delay in the 0.1 second range
the power system
Neutral voltage 59N Vrsd threshold = 30% of Vn
displacement if the Delay of a few seconds
generator is decoupled
If neutral Neutral voltage 59N Vrsd threshold = 30% of Vn
is isolated displacement Delay of a few seconds
Rotor frame Insulation monitoring device
fault
Field loss Directional reactive overpower 32Q Threshold 30% of Sn
Delay of a few seconds
Impedance measurement 40 Xa = 0.15 Zn, Xb = 1.15 Zn, Xc = 2.35 Zn
Zn circle delay: 0.1 second
Xd circle delay: discrimination with downstream protection
Pole slip Loss of synchronization 78PS Equal-area criterion: delay of 0.3 seconds
Power-swing criterion: 2 revolutions, 10 seconds between 2 power swings
Voltage Overvoltage 59 Threshold 110% of Un
regulation Delay of a few seconds
Undervoltage 27 Threshold 80% of Un
Delay of a few seconds
Frequency Overfrequency 81H Threshold + 2 Hz of rated frequency
regulation Underfrequency 81L Threshold - 2 Hz of rated frequency
Overheating of RTDs 38 According to manufacturer’s specifications
bearings
Power Directional active underpower 37P According to the application
management

58
Generator protection Examples of applications 0

DE57311

DE57312
38/ 27 38/ 21B
G 49T 32P G 49T 27
32Q 32P
49RMS 40
46 46
51G 49RMS
51V 51
51 51G
59 59
64REF 64REF
Vrsd 67 78PS
67N 81H
81H 81L
81L 87M

Low power generator Medium power generator

DE57313

DE572314
Vnt

38/ 27 38/ 12
G 49T 32P G 49T 14
32Q 21B
46 27
49RMS 32P
26 51 26 40
63 51G฀(2฀x) 63 46
49T 51V 49T 49RMS
59 50N
67 51
67N 51G
81H 59
81L 64G
64REF
78PS
81H
81L
87T

Low power generator-transformer Medium power generator-transformer

59
 Capacitor protection Types of faults 0

Capacitor banks are used to compensate for The main faults which are liable to affect capacitor banks are:
reactive energy drawn by power system b overloads,
b short-circuits,
b frame faults,
loads and occasionally in filters to reduce
harmonic voltage. Their role is to improve b short-circuit of an individual capacitor.

Overloads
the quality of the power system.
They may be connected in star, delta and
double star arrangements, depending on An overload is due to continuous or temporary overcurrent:
the level of voltage and the total rated power b continuous overcurrent due to:
v an increase in the supply voltage,
of the loads. v the flow of harmonic current due to the presence of non-linear loads such as static
A capacitor comes in the form of a case converters (rectifiers, variable speed drives), arc furnaces, etc.,
with insulating terminals on top. It comprises b temporary overcurrent due to energizing of a capacitor bank step.
individual capacitors (fig. 1) which have Overloads result in overheating which has an adverse effect on dielectric withstand
and leads to premature capacitor aging.
limited maximum permissible voltages
(e.g. 2250 V) and are mounted in groups: Short-circuits
b in series to obtain the required voltage A short-circuit is an internal or external fault between live conductors, phase-to-phase
withstand, (delta connection of capacitors) or phase-to-neutral (star connection).
b in parallel to obtain the desired power The appearance of gas in the gas-tight case of the capacitor creates overpressure
which may lead to the opening of the case and leakage of the dielectric.
rating.
Frame faults
There are 2 types of capacitor banks:
A frame fault is an internal fault between a live capacitor component and the frame
b without internal protection,
b with internal protection where a fuse made up of the metal case that is earthed for safety purposes.
is added for each individual capacitor. The fault current amplitude depends on the neutral earthing arrangement and
on the type of connection (star or delta).
Similar to an internal short-circuit, the appearance of gas in the gas-tight case
of the capacitor creates overpressure which may lead to the opening of the case
and leakage of the dielectric.

Short-circuit of an individual capacitor

Dielectric breakdown of an individual capacitor results in a short-circuit.
Without internal protection, the parallel-wired individual capacitors are shunted
DE55315

by the faulty unit:

b capacitor impedance is modified,
b the applied voltage is distributed to one less group in the series,
b each group is subjected to greater stress, which may result in further, cascading
breakdowns, until a full short-circuit.
Figure 2 shows the situation where group 2 is shunted following breakdown
of an individual capacitor.
With internal protection, blowing of the related internal fuse clears the faulty
individual capacitor:
b the capacitor remains fault-free,
b its impedance is modified accordingly.
Figure 3 shows the situation where the individual capacitor in group 2 is cleared
by its internal fuse and group 2 remains in service.
Fig. 1. Capacitor bank.

Group
DE57316EN

1 V
n฀–฀1
Group
2 V
Group
3 V
n฀–฀1

Group
n

Fig. 2. Capacitor bank without internal fuses. Fig. 3. Capacitor bank with internal
fuses.

60
Capacitor protection Protection functions 0

Capacitors should not be energized unless they have been discharged.

Re-energizing must be time-delayed in order to avoid transient overvoltages.
A 10-minute time delay allows for sufficient natural discharging.
Fast discharge inductors may be used to reduce discharging time.

Overloads
b Extended overcurrents due to increases in the supply voltage can be avoided
by overvoltage protection (ANSI 59) that monitors the power-system voltage.
This protection may cover the capacitor itself or a larger part of the power system.
Given that the capacitor can generally accommodate a voltage of 110% of its rated
voltage for 12 hours a day, this type of protection is not always necessary.
b Extended overcurrents due to the flow of harmonic current are detected by an overload
protection of one the following types:
v thermal overload (ANSI 49RMS),
v time-delayed overcurrent (ANSI 51), provided it takes harmonic frequencies
into account.
b The amplitude of short overcurrents due to the energizing of a capacitor bank step
is limited by mounting impulse inductors in series with each step.

Short-circuits
Short-circuits are detected by time-delayed overcurrent protection (ANSI 51).
Current and time-delay settings make it possible to operate with the maximum
permissible load current as well as close and switch capacitor bank steps.

Frame faults
This type of protection depends on the neutral earthing arrangement.
If the neutral is earthed, time-delayed earth fault protection (ANSI 51G) is used.

Capacitor component short-circuit

Fault detection is based on the modification of the impedance created:
b by short-circuiting the component for capacitors with no internal protection,
b by clearing the faulty individual capacitor for capacitors with internal fuses.
When the capacitor bank is double star-connected, the unbalance created by
the change in impedance in one of the stars causes current to flow in the connection
between the neutral points. This unbalance is detected by a time-delayed sensitive
overcurrent protection device (ANSI 51).

61
Capacitor protection Recommended settings
and examples of applications 0

Recommended settings
Faults Suitable protection functions ANSI code Setting information
Overloads Overvoltage 59 Threshold ð 110% Un
Thermal overload 49 RMS Threshold ð 1.3 In
Time constant in the 10-minute range
Time-delayed overcurrent 51 Threshold ð 1.3 In, IDMT curve
Short-circuits Time-delayed overcurrent 51 Threshold approximately 10 In
Time delay approximately 0.1 s (DT)
Frame faults Time-delayed earth fault 51N/51G Threshold ð 20% I maximum earth fault
Threshold Š 10% CT rating is supplied by 3 CTs, with H2 restraint
Time delay approximately 0.1 s (DT)
Capacitor Time-delayed overcurrent 51 Threshold approx. 1 A, depending on the application
component Time delay approximately 1 s (DT)
short-circuit

Examples of applications
DE57320

51G

Delta compensation
DE57321

DE57322

49RMS 49RMS
51,฀51G 51,฀51G
51 59

Double-star compensation Filtering assembly

62
Capacitor protection 0

63
Appendices Glossary
Key words and definitions
0

Key words Definitions

Active power in MW The part of the apparent power that can be converted into mechanical or thermal
power.
Aperiodic component Average value (that drops to zero) of the upper and lower envelopes of a current
during energization or the initiation of a short-circuit.
Apparent power in MVA Power in MVA drawn by the loads in a power system.
Blocking signal Order sent to an upstream protection device by a device that has detected a fault.
Breaking capacity Maximum current that a breaking device is capable of interrupting under prescribed
conditions.
Compensated neutral The power system is earthed via a reactor tuned to the phase-to-earth capacitances.
Compensation coil (Petersen coil) Neutral earthing reactor tuned to the phase-to-earth capacitances.
Core balance CT Current sensor used to measure the residual current by summing the magnetic
fields.
Cos ϕ Cosine of the angle between the fundamental components of the current and voltage.
Coupling Operation whereby a source or part of a power system is connected to a power
system already in operation when the necessary conditions are fulfilled.
Current sensor Device used to obtain a value related to the current.
Current-based discrimination Discrimination system based on the fact that the closer the fault is located to
the source, the stronger the fault current.
Decoupling Operation whereby a source or part of a power system is disconnected from a power
system.
Definite-time delay Time delay before device tripping that does not depend on the measured current.
Discrimination Capacity of a set of protection devices to distinguish between conditions
where a given protection device must operate and those where it must not.
Dynamic stability Capacity of a power system to return to normal operation following a sudden
disturbance.
Feeder Cables arriving from a set of busbars and supplying one or more loads or substations.
Harmonics Series of sinusoidal signals whose frequencies are multiples of the fundamental
frequency.
IDMT delay Variable time delay before device tripping that is inversely dependent upon
the measured current.
IEC 60909 International standard dealing with the calculation of short-circuit currents
in three-phase power systems.
Impedant neutral The power system is earthed via a resistance or a low reactance.
Incomer A line supplying energy from a source to the busbars of a substation.
Inrush current Transient current that occurs when a load is connected to a power system.
For inductive loads, it comprises an aperiodic component.
Insulation monitoring device (IMD) In an isolated neutral system, device that verifies the absence of a fault.
Isolated neutral The power-system neutral is not earthed except for high-impedance connections
to protection or measurement devices.
Load reconnection Restoration of supply to loads that have been shed, when normal power system
operating conditions have been re-established.
Load shedding Disconnection of non-priority loads from the power system when normal power
system operating conditions no longer exist.
Logic discrimination Discrimination system in which any protection device detecting a fault sends
a “no-trip” order (blocking signal) to the upstream protection device.
The upstream protection trips a circuit breaker only if it did not receive a blocking
signal from the downstream device.
Making capacity Maximum current that a breaking device is capable of making under prescribed
conditions. It is at least equal to the breaking capacity.
Neutral earthing Method by which the power system neutral is connected to earth.
Non-linear load Load drawing a current with a waveform that is not identical to that of the voltage.
Current variations are not proportional to the voltage variations.
Overload Overcurrent lasting a long time and affecting one of the elements in the power
system.

64
Appendices Glossary
Key words and definitions
0

Key words Definitions

Polarization voltage In a directional phase protection function, the phase-to-phase voltage value
in quadrature with the current for cos ϕ = 1. In a directional earth-fault protection
function, it is the residual voltage.
Power factor Ratio between the active power and the apparent power. For sinusoidal signals,
the power factor is equal to cos ϕ.
Power system Set of electrical-power production and consumption centres interconnected
by various types of conductors.
Protection settings Protection function settings determined by the protection-system study.
Protection system Set of devices and their settings used to protect power systems and their components
against the main faults.
Protection-system study Rational selection of all the protection devices for a power system, taking into account
its structure and neutral earthing system.
Rate of change of frequency (ROCOF) Protection used for rapid decoupling of a source supplying a power system
in the event of a fault.
Reactive power in Mvar The part of the apparent power that supplies the magnetic circuits of electrical
machines or that is generated by capacitors or the stray capacitance of the links.
Recloser Automatic device that recloses a circuit breaker that has tripped on a fault.
Residual current Sum of the instantaneous line currents in a polyphase power system.
Residual voltage Sum of the instantaneous phase-to-earth voltages in a polyphase power system.
Restricted earth fault protection Protection of a three-phase winding with earthed neutral against phase-to-earth faults.
Short-circuit Accidental contact between conductors or between a conductor and earth.
Short-circuit power Theoretical power in MVA that a power system can supply. It is calculated
on the basis of the rated power system voltage and the short-circuit current.
Solidly earthed neutral The power-system neutral is earthed via a connection with zero impedance.
Source transfer Operation whereby a power system is disconnected from one source and connected
to another. The sources may or may not be parallel connected.
Subtransient Period lasting between 0 and 100 ms following the appearance of a fault.
Symmetrical components Three independent single-phase systems (positive sequence, negative sequence
and zero sequence) superimposed to describe any real system.
System reconfiguration Operation, following an incident, involving switching of circuit breakers and switches
to resupply power system loads.
Time delay Intentional delay in the operation of a protection device.
Time-based discrimination Discrimination system in which protection devices detecting a fault are organized
to operate one after the other. The protection device closest to the source has
the longest time delay.
Total harmonic distortion Ratio of the rms value of the harmonics to that of the fundamental.
Transient Period lasting between 100 ms and 1 second following the appearance of a fault.
Tripping threshold Value of the monitored parameter that trips operation of the protection device.
Voltage sensor Device used to obtain a value related to the voltage.
Zero-sequence generator Three-phase transformer used to create a neutral point in a power system
for neutral earthing.

65
Appendices Bibliography 0

Types of documents Titles

Standards b IEC 60050 international electrotechnical vocabulary
b IEC 60044 current transformers
b IEC 60186 voltage transformers
b IEC 60255 electrical relays
b IEC 60909 calculation of short-circuit currents in three-phase AC systems
b IEEE C37.2 standard electrical power system device function numbers
and contact designations

Schneider Electric documentation b MV design guide

b Protection of power systems (Published by Hermès)
b MV partner
b Cahier technique publications
v N° 2 Protection of electrical distribution networks by the logic-selectivity system
v N° 18 Analysis of three-phase networks under transient conditions using
symmetrical components
v N° 62 Neutral earthing in an industrial HV network
v N° 113 Protection of machines and industrial HV networks
v N° 158 Calculation of short-circuit currents
v N° 169 HV industrial network design
v N° 174 Protection of industrial and tertiary MV networks
v N° 181 Directional protection equipment
v N° 189 Switching and protecting MV capacitor banks
v N° 192 Protection of MV/LV substation transformers
v N° 194 Current transformers: how to specify them
v N° 195 Current transformers: specification errors and solutions
b Schneider Electric site: http://www.schneider-electric.com
b Sepam protection-relay site: http://www.sepamrelay.com
b Sepam catalogues

General b Les techniques de l’ingénieur (Engineering techniques)

b Guide de l’ingénierie électrique (Electrical engineering handbook) (Lavoisier)

66
Appendices Definitions of symbols 0

Symbol Definition Symbol Definition

ALF accuracy-limit factor NPC neutral point coil
C capacitance of a phase with respect to earth Ph1 phase 1
CT current transformer Ph2 phase 2
D feeder circuit breaker Ph3 phase 3
Δt difference between the operating times of two protection R resistance
devices
dT tolerance of time delays RCT winding resistance in a current transformer
E phase-to-neutral voltage of the equivalent single-phase RN neutral-point earthing resistance
diagram
f power frequency Rs stabilization resistance in a differential circuit
I”k initial symmetrical short-circuit current Ssc short-circuit power
I0 zero-sequence component of current T tripping time delay
I1 positive-sequence component of current Td tripping time
I2 negative-sequence component of current THD total harmonic distortion
I1 phase 1 current Tmin circuit breaker breaking time
(minimum time before separation of 1st pole)
I2 phase 2 current tr protection overshoot time
I3 phase 3 current U phase-to-phase voltage
Ib symmetrical short-circuit current interrupted when the first Un rated phase-to-phase voltage
pole separates
Ic capacitive current Us phase-to-phase voltage threshold
IDC decreasing aperiodic component of the short-circuit V phase-to-neutral voltage
current
Ik continuous short-circuit current V0 zero-sequence component of voltage
Ik1 continuous phase-to-earth short-circuit current V1 positive-sequence component of voltage
Ik2 two-phase short-circuit current V2 negative-sequence component of voltage
Ik3 three-phase short-circuit current V1 phase 1 phase-to-neutral voltage
ILN current flowing in the neutral earthing reactor V2 phase 2 phase-to-neutral voltage
Im magnetizing current V3 phase 3 phase-to-neutral voltage
IMD insulation monitoring device Vk knee-point voltage
In rated current of an electrical component Vn rated phase-to-neutral voltage
IN current flowing in the solidly earthed neutral-point circuit Vrsd residual voltage
InCT rated current of a current transformer Vs phase-to-neutral voltage threshold
Ip peak value of short-circuit current VT voltage transformer
IpCT primary current in a current transformer X reactance
IRN circuit flowing in the neutral earthing resistor Xd synchronous reactance
Irsd residual current X’d transient reactance
Is current threshold setting X”d subtransient reactance
Isat saturation current in a current transformer Z0 zero-sequence impedance
Isc short-circuit current Z1 positive-sequence impedance
Iscmax the highest short-circuit current Z2 negative-sequence impedance
IsCT secondary current in a current transformer Za equivalent impedance
Ith maximum permissible current for 1 s Zn apparent rated impedance (transformer, capacitor, motor,
generator)
LN neutral-point earthing reactance ZN impedance between the neutral point and earth
LPCT low-power current transformer Zsc short-circuit impedance
m safety margin
MALT earthing

67
Appendices Index of technical terms 0

A I
aperiodic component 18 IEC 60909 17

B L
blocking signal 27, 31, 34, 35, 41, 42 line 18, 33, 44, 45
breaking capacity 18 load shedding 43
busbars 4, 5, 33 LPCT 19, 21

C M
cable 18, 33, 41, 44, 45 making capacity 18
capacitor 18, 27, 60, 61, 62 motor
capacitor bank 27 asynchronous 14, 50, 54, 55
characteristic angle 25 synchronous 14, 50, 53, 54
circuit breaker 17, 18, 27, 36–43, 45
circuit-breaker failure 43 N
coil neutral
extinction 10 compensated 6, 26, 37, 38
neutral point 9 impedant 26, 56, 58
Petersen 10 isolated 6, 7, 23
contactor 2, 18, 52, 54 solidly earthed 11, 37, 38
core balance CT 7, 8, 22, 26 neutral earthing 6-11
coupling 35, 39, 46, 57 neutral point 6–11, 37, 47, 48, 52, 56
current
residual 10, 22 O
short-circuit 12–19, 28, 30 overfluxing 47
current sensors 19-22, 33 overload 44, 47, 51, 56, 61
overvoltage 6–12, 61
D
decoupling 19, 26, 39 P
differential protection power
busbars 26 active 27, 39, 51, 53, 57, 58
generator 26 apparent 19, 23
high impedance 33, 58 rated output 19
line 26 reactive 53, 55, 57, 58
motor 26 short-circuit 11, 12, 45
percentage-based 48, 58 power system
restricted earth fault 26, 47, 48, 56, 58 architecture 3, 4, 5
transformer 26 loop 4, 5, 32, 35, 40, 41
discrimination radial 4, 5, 29, 31, 36
combined 34, 36 power factor 27
current-based 30, 34, 47 protection
differential 35 100% generator stator 26
directional 35 busbars 42, 43
logic 34, 35, 36 capacitor 60–62
time-based 28, 29, 31, 34, 35, 38 circuit breaker failure 26
differential 20, 26, 33, 35, 41, 42, 44, 47, 52, 53, 56
E directional active overpower 26
earthing 6–11 directional active underpower 26, 58
directional reactive overpower 26, 53, 58
F directional reactive underpower 26
fault, characterization 12, 18 distance 26, 45
fuse 18, 47, 50, 52, 60 excessive starting time and locked rotor 26, 51
field loss 26, 50, 52, 53, 55, 57, 58
G generator 55–59
generator 14–17, 33, 55–59 inadvertent generator energization 26
links 44, 45
H motor 50–54
harmonics 46, 47, 56, 58, 60 negative sequence / unbalance protection 26, 44, 53, 58
negative sequence overvoltage 26

68
Appendices Index of technical terms 0

neutral voltage displacement 26, 48, 53, 58 S

overcurrent saturation
delayed earth fault 11, 26, 44, 61, 62 of a CT 8, 19, 20, 22, 33, 42
delayed phase 26, 47, 52, 62 of a transformer 46
delayed voltage-restrained phase 26, 56 short-circuit
directional earth fault 7, 26, 37, 44, 52, 53 phase-to-earth 12, 14, 17
directional phase 26, 56, 58 phase-to-phase 12, 14, 17, 44, 47, 52, 56
earth fault 36, 37, 38, 40, 42, 48, 53, 56, 58 three-phase 12, 14, 17
instantaneous earth-fault 26 two-phase 15, 17
instantaneous phase 26, 47, 48 two-phase clear of earth 12
instantaneous voltage-restrained phase 26 two-phase-to-earth 7, 12, 15, 17
phase 20, 36, 38, 40, 44, 56 source transfer 39
overfluxing 26, 48, 57 subtransient 16, 17, 55
overfrequency 26, 58 switch 2, 18, 40
overspeed 26, 53, 58 symmetrical components 13, 14, 15, 17
overvoltage 26, 37, 47, 58, 62
phase undercurrent 26, 53 T
pole slip 26, 50-58 temperature 27, 47, 51, 52
positive sequence undervoltage 26, 51, 53 time
power system 36–41 operation 24, 28
pressure 26, 47, 48 overshoot 24, 28
rate of change of frequency (rocof) 26, 39, 43 reset 24, 25
recloser 26, 45 timer hold 25
remanent undervoltage 26, 51, 53 tripping 24, 25, 31, 34, 53
residual undervoltage (third harmonic) 26, 56, 58 time delay
RTD 26, 51, 53, 56, 58 definite 25
successive starts 26 IDMT 25
synchro-check 26, 39 total harmonic distortion 27
temperature monitoring 26 transformation ratio 23
thermal image 26, 44, 47, 51, 53, 56, 58, 61, 62 transformer
thermostat 26 current 19, 21, 27, 33, 35, 52
transformer 46–49 voltage 19, 23, 27, 32
underfrequency 26, 58 transformer energization 46
underimpedance 26, 53, 56, 57, 58 transient 6, 7, 10, 16, 46, 55
underspeed 26, 53, 58 tripping threshold 7, 25, 48
undervoltage 26, 57, 58
vector shift 26 Z
protection coordination 2 zero-sequence generator 8, 37, 38
protection relays 22, 24, 42
protection settings 14
protection system study 2, 3, 8, 9

R
rate of change of frequency 26, 39, 43
recloser 26, 45
residual voltage 7, 23, 37, 47, 52, 56
restraint
current 33
H2 (second harmonic) 22, 25, 47, 48, 62
H5 (fifth harmonic) 47
voltage 26, 56, 58
restricted earth fault 26, 47, 48, 56, 58

69
Appendices Notes 0

70
Appendices Notes 0

71
Appendices Notes 0

72
 ART.065193 © 2008 Schneider Electric - All rights reserved

Schneider Electric Industries SAS

Postal address: As standards, specifications and designs change from time to time, please ask for confirmation
89. Boulevard Franklin Roosevelt of the information given in this publication.
92500 Rueil-Malmaison (France)
This document has been
Tel.: +33 (0)1 41 29 85 00
printed on ecological paper
http://www.schneider-electric.com Design: Graphème
http://www.sepamrelay.com Publication: Schneider Electric
Printed: Imprimerie du Pont-de-Claix / JPF - Made in France

01/2008
CG0021EN