Octaverb

datasheet version: 041117

www.op-electronics.com

The Octaverb is a DSP based multieffect system with 10 types of reverb effects and 6 various effects divided in two
banks:

BANK A (reverbs):
1. Spring
2. Chapel
3. Gated
4. Reverse
5. Church
6. Room
7. Big Hall
8. Small Hall

BANK B (reverbs + other effects):

1. Slap Back Delay
2. Delay
3. Big Ambience
4. Early Reflection
5. Chorus
6. Echo
7. Flanger
8. Phaser

Banks are selected with a toggle switch and program effects are then selected with a rotary switch. Controls for MIX
and VOLUME are also present to balance the dry vs wet signal and output level signal.

Octaverb can be powered from negative-center 9V DC power supply and draws 140mA of current when fully
operational.

BUILDING INFO

PCB version 121017 misses a 100K resistor labeled as R in the partlist. You can just solder it on bottom side of the
pcb as shown in the following image:

solder the 100K resistor on bottom of the PCB

Leave 5V and RST pads disconnected

 Rotary switch, pots and toggle switch have to be mounted on pcb bottom side as shown:

Pots can be mounted both on pcb that wired witch cable. If you choose to mount on pcb make sure to align so that
they are not excessively high with respect to rotary and toggle switch:

Solder the rotary switch as shown:

 Value Package Parts Description
jumper L1
SPDT SPDT S2 Toggle Switch
0.47u E2,5-6 C2, C3, C17 POLARIZED CAPACITOR
1.2K 0204/7 R11 RESISTOR
100K 0204/7 R, R3, R18, R26 RESISTOR
100K LOG 16MM VOLUME POTENTIOMETER
100n C050B-025X075 C7, C9, C10, C11, C22, C24, C26, C27, C29 CAPACITOR
100p C050B-025X075 C12 CAPACITOR
100u E2,5-6 C23 POLARIZED CAPACITOR
10K 0204/7 R14, R25 RESISTOR
150p C050B-025X075 C28 CAPACITOR
10u E2,5-6 C20, C25 POLARIZED CAPACITOR
15n C050B-025X075 C15 CAPACITOR
16K 0204/7 R9 RESISTOR
1K 0204/7 R4 RESISTOR
150K 0204/7 R17 RESISTOR
1M 0204/7 R1, R6, R15, R16, R2 RESISTOR
1N4148 DO35 D1, D2 Fast Switching Diode
1P8T 1P8T-16MM S1 Rotary Switch
1N4001 DO41-3 D3 Rectifier Diodes
2.2K 0204/7 R7 RESISTOR
2.2n C050B-025X075 C5 CAPACITOR
220n C050B-025X075 C4, C13 CAPACITOR
220p C050B-025X075 C14 CAPACITOR
22p C050B-025X075 C18, C19 CAPACITOR
2K 0204/7 R8, R19, R20, R21, R22, R23, R24 RESISTOR
3.9K 0204/7 RLED RESISTOR
empty R5
390R 0204/7 R10 RESISTOR
4.7u E2,5-6 C6 POLARIZED CAPACITOR
47n C050B-025X075 C1 CAPACITOR
47u E2,5-6 C8, C21 POLARIZED CAPACITOR
50K LIN 16MM MIX POTENTIOMETER
10R 0204/7 R12, R13 RESISTOR
6.8n C050B-025X075 C16 CAPACITOR
L7805 TO220 IC6 VOLTAGE REGULATOR
12.28Mhz HC49U QF1 Monolithic Crystal
ATTINY25-20P* DIP8 U1 MCU
LED+ LED LED LED
TL072 DIL08-LP IC1, IC4 OP AMP
V1000** DIL16-500MIL IC3 DSP
V4420M** DIL28-6 IC2 AUDIO CODEC

* This is a pre-programmed microcontroller, it is included inside the kit but if you aim at building the Octaverb without the kit you need to purchase the pre-
programmed ATTINY25 from our store or program one yourself.
** These parts are SMD but are preassemblied on a breakout pcb so you can solder them as usual THT parts with help of pinhead connectors. Same as
above, they are included in the kit but if you aim at building the Octaverb without the kit you need to purchase the preassemblied V1000 and V4220M from
our store or make your own custom pcbs (Eagle files are available).