[Automation Server Family] SmartStruxure solution

I/O Module UI-16

16 channel universal input

Patented two-piece design

Each module can be separated from its terminal
base to allow the site to be wired prior to the
installation of the electronics. The patented locking
mechanism serves as handles for removing the
module from its base. All critical components have
a protective cover that permits convection cooling
to occur.

Introduction
The UI-16 is a universal input, 16 channel I/O
module.
Figure: Two-piece design
The universal inputs are ideal for any mix of Hot-connect and Hot-swap
temperature, pressure, flow, status points, and
Because critical applications require 24-hour
similar point types in a building control system. As
operation, Schneider Electric designed the I/O
counter inputs they are commonly used in energy
modules for hot-connection of terminal bases and
metering applications. As supervised inputs they
hot-swapping of the modules to their bases. This
are used for security applications where it is critical
design ensures continuous power and
to know whether or not a wire has been cut or
communication during service operations.
shorted. These events provide a separate indication
of alarms and trouble conditions to the system.
Auto-addressing
The auto-addressing feature eliminates the need for
Function
© 2014 Schneider Electric. All rights reserved.

setting DIP switches or pressing commission

Modular and scalable system buttons. With the Automation Server family, each
The modules are part of a modular system that module automatically knows its order in the chain
delivers power and communications on a common and assigns itself accordingly – significantly
bus. Connecting modules is a one-step process: reducing engineering and maintenance time.
just slide the modules together using the built-in
connectors. Simple DIN-rail installation
Fasteners easily snap into a locked position for
panel installation. The fastener has a quick-release
feature for easy DIN-rail removal.

Schneider Electric | Building Business www.schneider-electric.com/buildings

Trademarks and registered trademarks are the property of their respective owners.
03-14006-02-en July 2014
[Automation Server Family] SmartStruxure solution
2

Efficient terminal management LED status indicators

The I/O module terminals are clearly labelled and The I/O module has a status indicator that denotes
protected by transparent covers. The input and the health and status of the module.
output terminals are at the top and bottom of each
module and are accessible for maintenance without Each input channel has a dedicated two color
removing the module. The StruxureWare Building status LED. The LED can be configured to display
Operation WorkStation software can generate either red or green for each input state.
custom as-built labels for each module. Pre-
perforated letter and A4 size label sheets are Protection
available as an accessory. Protection components on the inputs protect
against high-voltage short-duration transient
Accommodates multiple row panel installations events.
The Automation Server module family uses built-in
connectors for single row connectivity, side by side. The current inputs are protected against over
If a panel size requires multiple rows, extension current.
cords are available.

Specifications
Input channels ........................................................................................................................................16
DC input supply power ......................................................................................................................1.8 W
DC input supply voltage ..................................................................................................................24 VDC
Environment
Ambient temperature, operating .............................................................................0 to 50 °C (32 to 122 °F)
Ambient temperature, storage .........................................................................-20 to +70 °C (-4 to +158 °F)
Maximum humidity...............................................................................................95 % RH non-condensing
Material
Plastic rating................................................................................................................................UL94-5VB
Enclosure....................................................................................................................Eco Friendly ABS/PC
Enclosure rating...................................................................................................................................IP 20
Mechanical
Dimensions including terminal base ..............................90 W x 114 H x 64 D mm (3.6 W x 4.5 H x 2.5 D in.)

© 2014 Schneider Electric. All rights reserved.

Weight including terminal base .........................................................................................0.269 kg (0.59 lb)

Weight excluding terminal base ........................................................................................0.146 kg (0.32 lb)
Terminal base .............................................................................................................................TB-IO-W1

Schneider Electric | Building Business www.schneider-electric.com/buildings

Trademarks and registered trademarks are the property of their respective owners.
03-14006-02-en July 2014
[Automation Server Family] SmartStruxure solution
3

Part numbers
UI-16, I/O module
16 universal inputs .........................................................................................................SXWUI16XX10001
TB-IO-W1, terminal base for I/O module
(Required for each I/O module)......................................................................................SXWTBIOW110001
Accessory part numbers
DIN-RAIL-CLIP, DIN-rail end clip
package of 25 pieces ....................................................................................................SXWDINEND10001
PRINTOUT-A4-W1, printout sheets for terminal labels
A4 sheet size, 100 sheets, 18 labels per sheet...............................................................SXWTERLBL10011
PRINTOUT-LTR-W1, printout sheets for terminal labels
Letter sheet size, 100 sheets, 16 labels per sheet ..........................................................SXWTERLBL10012
S-CABLE-L, S-cable extension cord for Automation Server I/O bus L shaped connectors
1.5 m............................................................................................................................SXWSCABLE10002
S-CABLE-L, S-cable extension cord for Automation Server I/O bus L shaped connectors
0.75 m..........................................................................................................................SXWSCABLE10003

Universal inputs
The universal inputs of the UI-16 I/O module are
designed to read several different types of inputs.

Input types:

• Digital
• Counter
• Supervised
• Voltage
• Current
• Temperature
• Resistive

Figure: Universal input internal configuration

Applied signals beyond the absolute maximum
ratings will cause over current in the protection
component DZ.
© 2014 Schneider Electric. All rights reserved.

The I/O bus in the terminal base provides the I/O

module with power and an address.

The address value in the I/O bus is increased by

one for each terminal base. The I/O bus also
enables RS-485 communication between the I/O
module and the Automation Server.

Schneider Electric | Building Business www.schneider-electric.com/buildings

Trademarks and registered trademarks are the property of their respective owners.
03-14006-02-en July 2014
[Automation Server Family] SmartStruxure solution
4

Digital inputs end of the cable close to the field contact, so that
The external connection of a digital input is shown the point where there is a risk that the circuit is
in the following figure. defeated is between the resistors and the I/O
module.

Three different types of supervised input

connections are supported:

• Series only
• Parallel only
• Series and parallel
Each type of supervised input connection provides
a different capability in regards to what form of
tamper/trouble can be detected regardless of
switch contact open or closed condition.

Figure: Digital input external connection A single resistor, which is connected in series with
the switch, can only detect tamper/trouble in the
K is the monitored external switch. form of a short circuit across the wire pair. The
external connection of a series only supervised
VS = 24 V input connection is shown in the following figure.

RPU = 10 kohm

Counter inputs
A counter input utilizes the same hardware
configuration as the digital input as shown in the
figure above.

Supervised inputs
Supervised inputs are contact closing inputs
supplemented with the supervision of the field
wiring integrity. This supervision is a required
feature in many security system applications. The
supervised inputs provide the ability to detect
specific forms of tampering or trouble with the wire Figure: Series only external connection
connections to the field contacts. The supervision is
achieved with a combination of 1 or 2 resistors K is the monitored external switch.
attached to the contact in the field. The resistor
combination creates continuous current flow VS = 5 V
through the field contact loop and presents a
defined set of expected resistance values for each RPU = 10 kohm
of the defined conditions. If someone is attempting
to defeat the monitoring of the field contact by short A single resistor, which is connected in parallel with
© 2014 Schneider Electric. All rights reserved.

circuiting the wire with a jumper or cutting the wire, the switch, can only detect tamper/trouble in the
the objective is to detect and indicate such a form of an open circuit in the field wiring loop. The
condition. The resistors need to be located at the external connection of a parallel only supervised
input connection is shown in the following figure.

Schneider Electric | Building Business www.schneider-electric.com/buildings

Trademarks and registered trademarks are the property of their respective owners.
03-14006-02-en July 2014
[Automation Server Family] SmartStruxure solution
5

Voltage inputs
The external connection of a voltage input is shown
in the following figure.

Figure: Parallel only external connection Figure: Voltage input external connection

K is the monitored external switch. VG is the monitored external voltage.

VS = 5 V RIN = 100 kohm

RPU = 10 kohm Current inputs

The external connection of a current input is shown
Two resistors, where one is connected in series in the following figure.
with the switch and one is connected in parallel with
the switch, can detect tamper/trouble conditions in
the form of both an open and a shorted circuit. The
external connection of a series and parallel
supervised input connection is shown in the
following figure.

Figure: Current input external connection

IG is the monitored external current.

RSH = 47 ohm

In the internal configuration of the current input,

there is a current limit circuit in order to protect the
shunt resistor from over load. The input current is
limited to 60 mA with a serial connected FET
transistor. If this limit is reached for 0.5 s, the
Figure: Series and parallel external connection transistor is turned off. When 5 s has elapsed, the
transistor is turned on again to make a new start
K is the monitored external switch. attempt.
© 2014 Schneider Electric. All rights reserved.

VS = 5 V Temperature inputs
RPU = 10 kohm The external connection of a temperature input is
shown in the following figure.

Schneider Electric | Building Business www.schneider-electric.com/buildings

Trademarks and registered trademarks are the property of their respective owners.
03-14006-02-en July 2014
[Automation Server Family] SmartStruxure solution
6

Thermistor VS RPU
type

The resulting voltage across the thermistor is

measured and a temperature is calculated
dependent on the selected thermistor type.

Resistive inputs
The external connection of a resistive input is
shown in the following figure.

Figure: Temperature input external connection

RT is the monitored external thermistor.

When a universal input is used as a temperature

input, VS and RPU in the internal configuration of the
universal input are used according to the following
table.

Thermistor VS RPU
type

20 kohm 5V 10 kohm

10 kohm 5V 10 kohm Figure: Resistive input external connection

RM is the monitored external resistance.
2.2 kohm 1V 1.5 kohm

1.8 kohm 1V 1.5 kohm VS = 5 V

1 kohm 1V 1.5 kohm RPU = 10 kohm

Specifications
Universal inputs

© 2014 Schneider Electric. All rights reserved.

Absolute maximum ratings ................................................................................................-0.5 to +24 VDC

Digital
Range .......................................Dry contract switch closure or open collector/open drain, 24 VDC, 2.4 mA
Minimum pulse width ......................................................................................................................120 ms

Schneider Electric | Building Business www.schneider-electric.com/buildings

Trademarks and registered trademarks are the property of their respective owners.
03-14006-02-en July 2014
[Automation Server Family] SmartStruxure solution
7

LED polarity ..................................Software selectable, if the LED is activated when the input is high or low
LED color ................................................................................................Red or green, software selectable
Counter
Range .......................................Dry contract switch closure or open collector/open drain, 24 VDC, 2.4 mA
Minimum pulse width ........................................................................................................................20 ms
Maximum frequency ..........................................................................................................................25 Hz
LED polarity ..................................Software selectable, if the LED is activated when the input is high or low
LED color ................................................................................................Red or green, software selectable
Supervised
5 V circuit, 1 or 2 resistors
Monitored switch combinations...........................................Series only, parallel only, and series and parallel
Resistor range.........................................................................................................................1 to 10 kohm
For a 2-resistor configuration, each resistor is assumed to have the same value +/- 5 %
Voltage
Range.......................................................................................................................................0 to 10 VDC
Accuracy .........................................................................................................+/-(7 mV + 0.2 % of reading)
Resolution..............................................................................................................................12 bit, 2.7 mV
Impedance...................................................................................................................................100 kohm
Reliability check .....................................................................................................................................Yes
Current
Range.........................................................................................................................................0 to 20 mA
Accuracy ....................................................................................................+/-(0.03 mA + 0.4 % of reading)
Resolution...............................................................................................................................12 bit, 5.6 μA
Impedance ......................................................................................................................................47 ohm
Reliability check .....................................................................................................................................Yes
Resistive
10 ohm to 10 kohm accuracy .................................................................................+/-(7 + 4 x 10-3 x R) ohm
R = Resistance in ohm
10 to 60 kohm accuracy.........................................................................+/-(4 x 10-3 x R + 7 x 10-8 x R2) ohm
R = Resistance in ohm
Reliability check .....................................................................................................................................Yes
Temperature
Range .........................................................................................................-50 to +150 °C (-58 to +302 °F)
© 2014 Schneider Electric. All rights reserved.

Resolution...........................................................................................................................................12 bit
Reliability check .....................................................................................................................................Yes
Supported thermistors
Honeywell ......................................................................................................................................20 kohm
Type I (Continuum) .........................................................................................................................10 kohm
Type II (I/NET).................................................................................................................................10 kohm
Type III (Satchwell)..........................................................................................................................10 kohm
Type IV (FD)................................................................................................................................... 10 kohm

Schneider Electric | Building Business www.schneider-electric.com/buildings

Trademarks and registered trademarks are the property of their respective owners.
03-14006-02-en July 2014
[Automation Server Family] SmartStruxure solution
8

Type V (FD w/ 11k shunt)...............................................................................................Linearized 10 kohm

Satchwell D?T ...............................................................................................................Linearized 10 kohm
Johnson Controls..........................................................................................................................2.2 kohm
Xenta ............................................................................................................................................1.8 kohm
Balco ...............................................................................................................................................1 kohm
Thermistor accuracy
20 kohm, 10 kohm, 2.2 kohm, and 1.8 kohm....................-50 to -30 °C: +/-1.5 °C (-58 to -22 °F: +/-2.7 °F)
...........................................................................................-30 to 0 °C: +/-0.5 °C (-22 to +32 °F: +/-0.9 °F)
............................................................................................. 0 to 50 °C: +/-0.2 °C (32 to 122 °F: +/-0.4 °F)
....................................................................................... 50 to 100 °C: +/-0.5 °C (122 to 212 °F: +/-0.9 °F)
..................................................................................... 100 to 150 °C: +/-1.5 °C (212 to 302 °F: +/-2.7 °F)
Linearized 10 kohm ..........................................................-50 to -30 °C: +/-3.0 °C (-58 to -22 °F: +/-5.4 °F)
...........................................................................................-30 to 0 °C: +/-1.0 °C (-22 to +32 °F: +/-1.8 °F)
............................................................................................. 0 to 50 °C: +/-0.3 °C (32 to 122 °F: +/-0.5 °F)
....................................................................................... 50 to 100 °C: +/-0.5 °C (122 to 212 °F: +/-0.9 °F)
..................................................................................... 100 to 150 °C: +/-2.0 °C (212 to 302 °F: +/-3.6 °F)
1 kohm .......................................................................-50 to +150 °C: +/-1.5 °C (-58 to +302° F: +/-2.7 °F)

For protection from excess current that could be • Individual 24 VDC power sources to the field
produced by field wiring, follow these instructions: must be current limited to maximum of 4
amps for UL compliant installations, and no
• Connect one RET terminal on each of the I/O more than 6 amps in other areas.
modules to a common chassis/power ground
• For more information on wiring, see
rail in the control panel using a size 16 AWG,
Automation Server Family Hardware Guide.
1.3 mm, or larger wire.

Regulatory Notices
Federal Communications Commission CE - Compliance to European Union (EU)
FCC Rules and Regulations CFR 47, Part 15, Class B 2004/108/EC Electromagnetic Compatibility Directive
This device complies with part 15 of the FCC Rules. Operation is subject to the following This equipment complies with the rules, of the Official Journal of the European Union, for
two conditions: (1) This device may not cause harmful interference. (2) This device must governing the Self Declaration of the CE Marking for the European Union as specified in
accept any interference received, including interference that may cause undesired the above directive(s) per the provisions of the following standards: IEC/EN 61326-1
operation. Product Standard, IEC/EN 61010-1 Safety Standard.

Industry Canada
ICES-003 WEEE - Directive of the European Union (EU)
This is a Class B digital device that meets all requirements of the Canadian Interference This equipment and its packaging carry the waste of electrical and electronic equipment
Causing Equipment Regulations. (WEEE) label, in compliance with European Union (EU) Directive 2002/96/EC, governing
the disposal and recycling of electrical and electronic equipment in the European
community.
C-Tick (Australian Communications Authority (ACA))
AS/NZS 3548
This equipment carries the C-Tick label and complies with EMC and radio UL 916 Listed products for the Unites States and Canada, Open Class Energy
communications regulations of the Australian Communications Authority (ACA), governing Management Equipment.
the Australian and New Zealand (AS/NZS) communities.
© 2014 Schneider Electric. All rights reserved.

Schneider Electric | Building Business www.schneider-electric.com/buildings

Trademarks and registered trademarks are the property of their respective owners.
03-14006-02-en July 2014