Energy Tips Pumping Systems

Pumping Systems Tip Sheet #2 October 2005

Industrial Technologies Program

Suggested Actions
Accurately identify process flow rate and pressure requirements. Measure actual head and flow rate. Develop a system curve. Select a pump with high efficiency over the expected range of operating conditions. Specify electric motors that meet the NEMA Premium full-load efficiency standards. Use life cycle costing techniques to justify acquiring high efficiency pumps and designing efficient systems.

Pump Selection Considerations

Understanding Your Pumping System Requirements
Pumps transfer liquids from one point to another by converting mechanical energy from a rotating impeller into pressure energy (head). The pressure applied to the liquid forces the fluid to flow at the required rate and to overcome friction (or head) losses in piping, valves, fittings, and process equipment. The pumping system designer must consider fluid properties, determine end use requirements, and understand environmental conditions. Pumping applications include constant or variable flow rate requirements, serving single or networked loads, and consisting of open loops (nonreturn or liquid delivery) or closed loops (return systems).

Fluid Properties
The properties of the fluids being pumped can significantly affect the choice of pump. Key considerations include: Acidity/alkalinity (pH) and chemical composition. Corrosive and acidic fluids can degrade pumps, and should be considered when selecting pump materials. Operating temperature. Pump materials and expansion, mechanical seal components, and packing materials need to be considered with pumped fluids that are hotter than 200F. Solids concentrations/particle sizes. When pumping abrasive liquids such as industrial slurries, selecting a pump that will not clog or fail prematurely depends on particle size, hardness, and the volumetric percentage of solids. Specific gravity. The fluid specific gravity is the ratio of the fluid density to that of water under specified conditions. Specific gravity affects the energy required to lift and move the fluid, and must be considered when determining pump power requirements. Vapor pressure. A fluids vapor pressure is the force per unit area that a fluid exerts in an effort to change phase from a liquid to a vapor, and depends on the fluids chemical and physical properties. Proper consideration of the fluids vapor pressure will help to minimize the risk of cavitation. Viscosity. The viscosity of a fluid is a measure of its resistance to motion. Since kinematic viscosity normally varies directly with temperature, the pumping system designer must know the viscosity of the fluid at the lowest anticipated pumping temperature. High viscosity fluids result in reduced centrifugal pump performance and increased power requirements. It is particularly important to consider pump suction-side line losses when pumping viscous fluids.

Resources
DOE and Hydraulic Institute, Improving Pumping System Performance: A Sourcebook for Industry. Hydraulic InstituteHI is a nonprofit industry association for pump and pump system manufacturers; it provides product standards and a forum for the exchange of industry information for management decisionmaking. In addition to the ANSI/HI pump standards, HI has a variety of energy-related resources for pump users and specifiers, including training, guidebooks, and more. For more information, visit www.pumps. org, www.pumplearning.org, and www.pumpsystemsmatter.org. U.S. Department of EnergyDOEs Pumping System Assessment Tool (PSAT) can help you assess pumping system efficiency and estimate energy and cost savings. PSAT uses pump performance data from Hydraulic Institute standards and motor performance data from the MotorMaster+ database. Visit the BestPractices Web site at www.eere.energy.gov/bestpractices for more information on PSAT and for upcoming training in improving pumping system performance and in becoming a qualified pumping system specialist.

End Use RequirementsSystem Flow Rate and Head

The design pump capacity, or desired pump discharge in gallons per minute (gpm) is needed to accurately size the piping system, determine friction head losses, construct a system curve, and select a pump and drive motor. Process requirements may be met by providing a constant flow rate (with on/off control and storage used to satisfy variable flow rate requirements), or by using a throttling valve or variable speed drive to supply continuously variable flow rates. The total system head has three components: static head, elevation (potential energy), and velocity (or dynamic) head. Static head is the pressure of the fluid in the system, and is the quantity measured by conventional pressure gauges. The height of the fluid

level can have a substantial impact on system head. The dynamic head is the pressure required by the system to overcome head losses caused by flow rate resistance in pipes, valves, fittings, and mechanical equipment. Dynamic head losses are approximately proportional to the square of the fluid flow velocity, or flow rate. If the flow rate doubles, dynamic losses increase fourfold. For many pumping systems, total system head requirements vary. For example, in wet well or reservoir applications, suction and static lift requirements may vary as the water surface elevations fluctuate. For return systems such as HVAC circulating water pumps, the values for the static and elevation heads equal zero. You also need to be aware of a pumps net positive suction head requirements. Centrifugal pumps require a certain amount of fluid pressure at the inlet to avoid cavitation. A rule of thumb is to ensure that the suction head available exceeds that required by the pump by at least 25% over the range of expected flow rates.

BestPractices is part of the Industrial Technologies Program Industries of the Future strategy, which helps the countrys most energy-intensive industries improve their competitiveness. BestPractices brings together emerging technologies and best energy-management practices to help companies begin improving energy efficiency, environmental performance, and productivity right now. BestPractices emphasizes plant systems, where significant efficiency improvements and savings can be achieved. Industry gains easy access to near-term and long-term solutions for improving the performance of motor, steam, compressed air, and process heating systems. In addition, the Industrial Assessment Centers provide comprehensive industrial energy evaluations to small- and medium-size manufacturers.

Environmental Considerations
Important environmental considerations include ambient temperature and humidity, elevation above sea level, and whether the pump is to be installed indoors or outdoors.

Software Tools
Most pump manufacturers have developed software or Web-based tools to assist in the pump selection process. Pump purchasers enter their fluid properties and system requirements to obtain a listing of suitable pumps. Software tools that allow you to evaluate and compare operating costs are available from private vendors.

FOR ADDITIONAL INFORMATION, PLEASE CONTACT: EERE Information Center 1-877-EERE-INF (1-877-337-3463) www.eere.energy.gov Industrial Technologies Program Energy Efficiency and Renewable Energy U.S. Department of Energy Washington, DC 20585-0121 www.eere.energy.gov/industry

Reference
Centrifugal/Vertical NPSH Margin (ANSI/HI 9.6.1-1998), www.pumps.org, Hydraulic Institute, 1998.

About DOEs Industrial Technologies Program

The Industrial Technologies Program, through partnerships with industry, government, and non-governmental organizations, develops and delivers advanced energy efficiency, renewable energy, and pollution prevention technologies for industrial applications. The Industrial Technologies Program is part of the U.S. Department of Energys Office of Energy Efficiency and Renewable Energy. The Industrial Technologies Program encourages industry-wide efforts to boost resource productivity through a strategy called Industries of the Future (IOF). IOF focuses on the following eight energy and resource intensive industries: Forest Products Metal Casting Petroleum Aluminum Glass Mining Steel Chemicals The Industrial Technologies Program and its BestPractices activities offer a wide variety of resources to industrial partners that cover motor, steam, compressed air, and process heating systems. For example, BestPractices software can help you decide whether to replace or rewind motors (MotorMaster+), assess the efficiency of pumping systems (PSAT), compressed air systems (AirMaster+), steam systems (Steam Scoping Tool), or determine optimal insulation thickness for pipes and pressure vessels (3E Plus). Training is available to help you or your staff learn how to use these software programs and learn more about industrial systems. Workshops are held around the country on topics such as Capturing the Value of Steam Efficiency, Fundamentals and Advanced Management of Compressed Air Systems, and Motor System Management. Available technical publications range from case studies and tip sheets to sourcebooks and market assessments. The Energy Matters newsletter, for example, provides timely articles and information on comprehensive energy systems for industry. You can access these resources and more by visiting the BestPractices Web site at www.eere.energy.gov/ industry/bestpractices or by contacting the EERE Information Center at 877-337-3463 or via email at www.eere.energy.gov/informationcenter/.

A S TRONG E NERGY P ORTFOLIO FOR A S TRONG A MERICA

Energy efficiency and clean, renewable energy will mean a stronger economy, a cleaner environment, and greater energy independence for America. Working with a wide array of state, community, industry, and university partners, the U.S. Department of Energys Office of Energy Efficiency and Renewable Energy invests in a diverse portfolio of energy technologies. DOE/GO-102005-2156 October 2005 Pumping Systems Tip Sheet #2