CDP-S3

SERVICE MANUAL AEP Model

UK Model
Ver 1.0 2001.04
E Model
Australian Model

CDP-S3 is the CD player section

in MHC-S7AV or MHC-S3.

Model Name Using Similar Mechanism NEW

CD Mechanism Type CDM63B-30BD60
Base Unit Name BU-30BD60
Optical Pick-up Name OP Assy (A-MAX.3)

SPECIFICATIONS

System Compact disc and digital

audio system
Laser Semiconductor laser
(λ=780 nm)
Emission duration:
continuous
Frequency response 2 Hz – 20 kHz (±0.5 dB)
Signal-to-noise ratio More than 90 dB
Dynamic range More than 90 dB
OPTICAL OUT
(Square optical connector jack, rear panel)
Dimensions (w/h/d) Approx. 280 x 108 x 330 mm
Mass Approx. 2.7 kg

Design and specifications are subject to change

without notice.

COMPACT DISC PLAYER

9-873-831-11 Sony Corporation
2001D0500-1 Home Audio Company
C 2001.4 Shinagawa Tec Service Manual Production Group

Downloaded from www.Manualslib.com manuals search engine

 CDP-S3

NOTES ON HANDLING THE OPTICAL PICK-UP CAUTION

BLOCK OR BASE UNIT Use of controls or adjustments or performance of procedures
The laser diode in the optical pick-up block may suffer electro- other than those specified herein may result in hazardous ra-
static break-down because of the potential difference generated diation exposure.
by the charged electrostatic load, etc. on clothing and the human
body.
During repair, pay attention to electrostatic break-down and also
use the procedure in the printed matter which is included in the
This appliance is classified as a CLASS 1 LASER product.
repair parts.
The CLASS 1 LASER PRODUCT MARKING is located on
The flexible board is easily damaged and should be handled with
the rear exterior.
care.

NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused

on the disc reflective surface by the objective lens in the optical
pick-up block. Therefore, when checking the laser diode emis-
sion, observe from more than 30 cm away from the objective lens.
Laser component in this product is capable of emitting radiation
exceeding the limit for Class 1.
LASER DIODE AND FOCUS SEARCH OPERATION
CHECK
The following caution label is located inside the unit.
Carry out the “S curve check” in “CD section adjustment” and
check that the S curve waveforms is output three times.

Notes on chip component replacement

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be dam-
aged by heat.

Flexible Circuit Board Repairing

• Keep the temperature of the soldering iron around 270 ˚C dur-
ing repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board. (within 3 times)
• Be careful not to apply force on the conductor when soldering
or unsoldering.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED
LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS
AND IN THE PARTS LIST ARE CRITICAL TO SAFE
OPERATION. REPLACE THESE COMPONENTS WITH
SONY PARTS WHOSE PART NUMBERS APPEAR AS
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUB-
LISHED BY SONY.

2
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

TABLE OF CONTENTS

1. SERVICING NOTES ............................................... 4

2. GENERAL ................................................................... 5

3. DISASSEMBLY
3-1. Disassembly Flow ........................................................... 6
3-2. Cover ............................................................................... 7
3-3. CD Mechanism Deck (CDM63B-30BD60) ................... 7
3-4. MAIN Board ................................................................... 8
3-5. Front Panel Section ......................................................... 8
3-6. PANEL (L) Board, PANEL (R) Board ........................... 9
3-7. Lid (CD) .......................................................................... 9

4. TEST MODE .............................................................. 10

5. ELECTRICAL ADJUSTMENTS ......................... 11

6. DIAGRAMS
6-1. Note for Printed Wiring Boards
and Schematic Diagrams ................................................ 12
6-2. Printed Wiring Board – BD Section – ........................... 14
6-3. Schematic Diagram –BD Section – ............................... 15
6-4. Printed Wiring Boards – CD CHANGER Section – ..... 16
6-5. Schematic Diagram – CD CHANGER Section – ......... 17
6-6. Printed Wiring Board – MAIN Section – ...................... 18
6-7. Schematic Diagram – MAIN Section – ......................... 19
6-8. Printed Wiring Boards – PANEL Section – .................. 20
6-9. Schematic Diagram – PANEL Section – ....................... 21
6-10. IC Pin Function Description ........................................... 24

7. EXPLODED VIEWS
7-1. General Section ............................................................... 26
7-2. CD Mechanism Deck Section-1
(CDM63B-30BD60) ....................................................... 27
7-3. CD Mechanism Deck Section-2
(CDM63B-30BD60) ....................................................... 28
7-4. Base Unit Section (BU-30BD60) ................................... 29

8. ELECTRICAL PARTS LIST ............................... 30

3
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3
SECTION 1
SERVICING NOTES
This set is a component of the MHC-S7AV or MHC-S3. CD-TEXT TEST DISC
The MHC-S7AV or MHC-S3 system configuration is as shown
below, and therefore it does not operate normally unless all four This unit is able to display the test data (character information)
components are connected. written in the CD on its fluorescent indicator tube.
In performing the repair, connect all components with the system The CD-TEXT TEST DISC (TGCS-313:4-989-366-01) is used
cables. for checking the display.
Note: The precaution to the users is described on the label stuck on To check, perform the following procedure.
the back panel (CD player) and in the troubleshooting section in
the Operation Manual. Checking Method:
1. Press the I/1 button to turn the power on, set the disc to the
System Configuration: disc table with the “test disc” label facing up, and chuck the
disc.
AC IN
2. Press the [CD] button to set CD function, and press the
TA n N button to playback the disc.
3. The following will be displayed on the liquid crystal display.
Display : 1KHZ/0DB/L R
POWER SUPPLY 4. Pressing the [-- .] or [> +] button, select the track. The text
data of each track will be displayed.
For details of the displayed contents for each track, refer to “Table
1 : CD-TEXT TEST DISC TEXT Data Contents”.

ST Restrictions in CD-TEXT Display

In this unit, some special characters will not be displayed prop-
erly. These will be displayed as a space or a character resembling
SYSTEM & CD µcon it.

DISPLAY Table 1 : CD-TEXT TEST DISC TEXT Data Contents

(TRACKS No. 1 to 20:Normal Characters)
TRACK
Displayed Contents
No.

CDP 1
2
1kHz/0dB/L&R
20Hz/0dB/L&R
3 40Hz/0dB/L&R
4 100Hz/0dB/L&R
5 200Hz/0dB/L&R
TC 6 500Hz/0dB/L&R
7 1kHz/0dB/L&R
TC µcon
8 5kHz/0dB/L&R
9 7kHz/0dB/L&R
10 10kHz/0dB/L&R
11 16kHz/0dB/L&R
12 18kHz/0dB/L&R
13 20kHz/0dB/L&R
14 1kHz/0dB/L&R
15 1kHz/–1dB/L&R
16 1kHz/–3dB/L&R
17 1kHz/–6dB/L&R
18 1kHz/–10dB/L&R
19 1kHz/–20dB/L&R
20 1kHz/–60dB/L&R
Note: Track No. 21 to 99 are not displayed.

4
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3
SECTION 2 This section is extracted from
GENERAL instruction manual.

Parts Identification

The items are arranged in alphabetical order.

Refer to the pages indicated in parentheses ( ) for details.

Main unit Remote Control

wj wkwl e; ea 1 2 3 CD H es (14, 15)

CHECK 5 (15)
CLEAR 6 (15)
CLOCK/TIMER SELECT qj
m M

(30)
es es H
4
. >

CLOCK/TIMER SET qk (13, 21,

1 2 3 H S x ed ea hH
5 29)
e; hH 6 DBFB qg (23)
wl 7 DISPLAY ws (13, 16, 18, 29, 35)
wk . > x 8 D.SKIP 4 (14)
wj 9 ENTER wg (10, 12, 13, 15, 17,
ek ej eh eg ef m M X

q; 18, 21, 22, 26–30)

wh O
EQ qd (27)
wg P p qa EQ ON/OFF qf (10, 28)
o FUNCTION wf (10, 14, 15, 20,
DISC 1–3 ek (14, 15, 21) qs
wf 21, 31)
DISC 1–3 indicators ej qd GROOVE wa (23)
DISC 1–3 Z (eject) wl (14) wd qf SET UP qs (10, 12, 26, 28, 29)
PLAY MODE wj (14, 15, 21) ws qg SLEEP 7 (29)
REPEAT wk (14) wa
SUR wd (25)
N (play) eh (14, 15) w; qh TAPE A hH ea (19, 35)
X (pause) eg (14) ql TAPE B hH e; (19, 20, 35)
x (stop) ef (14, 20) qk qj TUNER/BAND wl (17)
. (go back) ed (14, 15, 21)
TUNING + 9 (17)
> (go forward) es (14, 15, 21)
TUNING – wh (17)
m (rewind) e; (14)
TV CH +/– ql
M (fast forward) ea (14)
TV VOL +/– w;
TV @/1 2
TV/VIDEO 1
VOL +/– qh

BUTTON DESCRIPTIONS

@/1 (power) 3
X (pause) q;
x (stop) 8
. (go back) wk
> (go forward) wj
m (rewind) wh
M (fast forward) 9
O/o/P/p qa

5
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3
SECTION 3
DISASSEMBLY
• This set can be disassembled in the order shown below.

3-1. DISASSEMBLY FLOW

SET

3-2. COVER
(Page 7)

3-3. CD MECHANISM DECK

3-4. MAIN BOARD 3-5. FRONT PANEL SECTION
(CDM63B-30BD60)
(Page 8) (Page 8)
(Page 7)

3-6. PANEL (L) BOARD,

PANEL (R) BOARD
(Page 9)

3-7. LID (CD)

(Page 9)

6
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

Note: Follow the disassembly procedure in the numerical order given.

3-2. COVER

2 screw
3 cover
(BVTT3 × 6)

1 two screws
(case 3 TP2)

1 two screws
(case 3 TP2)

3-3. CD MECHANISM DECK (CDM63B-30BD60)

4 CD mechanism deck
(CDM63B-30BD60)

2 connector
(CN701)

1 wire (flat type) (21 core)

(CN301)
3 four screws
(BVTP3 × 8)

7
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

3-4. MAIN BOARD

2 two connectors
(CN101, 102)

1 wire (flat type) (21 core)

(CN301)
5 MAIN board

2 connector
(CN401) 3 screw
(BVTP3 × 8)

3 two screws
(BVTP3 × 8)

4 lug

3 screw
2 connector (BVTP3 × 8)
(CN701)

3-5. FRONT PANEL SECTION

1 connector
(CN401)

3 claw

4 front panel section

3 two claws
2 three screws
(BVTP3 × 8)

8
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

3-6. PANEL (L) BOARD, PANEL (R) BOARD

4 four screws
(BVTP2.6 × 8)
6 PANEL (R) board

5 two claws
1 five screws
(BVTP2.6 × 8)

3 PANEL (L) board

2 two claws

3-7. LID (CD)

2 bracket (LID) assy

1 screw
(BVTP2.6 × 8)

4 spring (CD)

3 lid (CD)

9
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3
SECTION 4
TEST MODE
Note: Use flowing buttons in the test mode. [CD Service Mode]
no mark : Button of CD unit (CDP-S3) • This mode can run the CD sled motor optionally. Use this mode,
*1 : Button of amplifier unit (TA-S7AV or TA-S3) for instance, when cleaning the optical pick-up.
*2 : Button of tuner unit (ST-S5 or ST-S3)
Procedure:
1. Press the I/1 *1 button to turn the power on.
[CD Delivery Mode]
2. Turn the [FILE SELECT] *1 knob to set the CD function.
• This mode moves the optical pick-up to the position durable to
3. While pressing the both [PLAY MODE] and [x] buttons, press
vibration. Use this mode when returning the set to the customer
the [.] button.
after repair.
4. Set to the CD service mode.
Procedure:
5. With the CD in stop status, press the [M] button to move the
1. Press the I/1 *1 button to turn the power on.
optical pick-up to outside track, or press the [m ] button to
2. Turn the [FILE SELECT] *1 knob to set the CD function.
inside track.
3. While pressing the [EQ ON/OFF] *1 button, press the I/1 *1
6. To release from this mode, perform as follows.
button.
1) Move the optical pick-up to the most inside track.
4. The message “LOCK” is displayed on the fluorescent indica-
2) Disconnect the power cord.
tor tube of tuner unit and turn the power off automatically, and Notes: • Always move the optical pick-up to most inside track when
the CD delivery mode is set. releasing from this mode. Otherwise, a disc will not be un-
loaded.
[GC Test Mode] • Do not run the sled motor excessively, otherwise the gear can
Enter the GC Test Mode be chipped.
Procedure 1:
1. Press the I/1 *1 button to turn the power on. [CD Cancellation Mode of Repeat Limitation]
2. While pressing the both [PLAY MODE] and [x] buttons, press • This mode can cancel the CD repeat limitation (5 times).
the [Z] (DISC 1) button. Procedure:
3. LEDs and fluorescent indicator tube are all turned on of all 1. Press the I/1 *1 button to turn the power on.
units. 2. Turn the [FILE SELECT] *1 knob to set the CD function.
3. While pressing the both [PLAY MODE] and [x] buttons, press
Procedure 2: the [REPEAT] button.
1. Press the I/1 *1 button to turn the power on. 4. CD repeat limitation is canceled.
2. While pressing the both [STEREO/MONO] *2 and 5. To release this mode, disconnect the power cord.
[CINEMA STUDIO C] *1 buttons, press the [CLOCK/TIMER]
*2 button.
3. LEDs and fluorescent indicator tube are all turned on of all
units.

Version Display Mode

Procedure:
1. Enter the GC test mode.
2. Each time the [DISC 1] or [TUNER MEMORY] *2 button is
pressed, microcomputer or mechanism deck version is dis-
played of each unit.
3. Press the [DISC 3] or [TUNING +] *2 button to detail is dis-
played the version.

Key Check Mode

Procedure:
1. Enter the GC test mode.
2. Press the [DISC 2] or [TUNING --] *2 button to set the key
check mode, and displays “K 0 J 0 V 0” on the fluorescent
indicator tube of tuner unit.
3. All buttons are pressed of CD unit, all LEDs are blinking of
CD unit. (not change the display of fluorescent indicator tube)

Releasing the GC Test Mode

To release from this mode, press three buttons in the same manner
as entering this mode or disconnect the power cord.

10
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3
SECTION 5
ELECTRICAL ADJUSTMENTS
Note : E-F Balance (1 Track jump) Check
1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given. oscilloscope
2. Use LUV-P01 (4-999-032-01) unless otherwise indicated. BD board
3. Use an oscilloscope with more than 10MΩ impedance.
4. Clean the object lens by an applicator with neutral detergent TP(TEO)
TP(DVC)
when the signal level is low than specified value with the
following checks.
Procedure :
S-Curve Check 1. Connect an oscilloscope to TP (TEO) and TP (DVC).
Oscilloscope
2. Turn Power switch on.
BD board 3. Load a disc (LUV-P01) and playback the number nine track.
4. Press the N button. (Becomes the 1 track jump mode.)
TP(FEO) 5. Confirm that the level B and A (DC voltage) on the oscilloscope
TP(DVC) waveform.

1 track jump waveform center of

Procedure :
1. Connect an oscilloscope to TP (FEO). waveform
2. Connect between TP (FEI) and TP (DVC) ( 1.65 V) by lead
wire. B
3. Turn Power switch on. A (DC voltage)
4. Load a disc (LUV-P01) and actuate the focus search. (In DVC
consequence of open and close the disc tray, actuate the focus
search) level=1.0 ±0.5Vp-p symmetry
5. Confirm that the oscilloscope waveform (S-curve) is
symmetrical between A and B. And confirm peak to peak level
within 2 ± 0.5 Vp-p. 6. Adjust RV101 on the BD board so that the center of waveform
S-curve waveform becomes the same voltage of DVC. (i.e. A=0V)
symmetry
Adjustment Location:

A [BD BOARD] (Conductor Side)

within 2 ±0.5Vp-p
B

6. After check, remove the lead wire connected in step 2.

Note : • Try to measure several times to make sure than the ratio
of A : B or B : A is more than 10 : 7.
• Take sweep time as long as possible and light up the
brightness to obtain best waveform.
TP (DVC)
TP
RF Level Check (RFAC) 15 1
IC103 21 20
BD board oscilloscope
16 30
TP (FEO)
TP(RFDC) 40 1
TP(RFAC) IC101
TP TP (TEO) 41 80
TP(DVC) (FEI) TP
(RFDC) 60 61
Procedure : RV101
1. Connect an oscilloscope CH1 to TP (RFDC) and CH2 to TP
(RFAC).
2. Turn Power switch on.
3. Load a disc (LUV-P01) and playback.
4. Confirm that oscilloscope waveform is clear and check if RF
signal level is correct or not.
Note : Clear RF signal waveform means that the shape “ ◊ ” can be clearly
distinguished at the center of the waveform.

RF signal waveform
VOLT/DIV : 200mV
TIME/DIV : 500ns

level : 0.65 ±0.15Vp-p (RFDC)

1.1 ±0.4Vp-p (RFAC)

11
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3
SECTION 6
DIAGRAMS
6-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
(In addition to this, the necessary note is printed in each block)

Note on Printed Wiring Boards: Note on Schematic Diagram:

• X : parts extracted from the component side. • All capacitors are in µF unless otherwise noted. pF: µµF
• Y : parts extracted from the conductor side. 50 WV or less are not indicated except for electrolytics
• f : internal component. and tantalums.
• : Pattern from the side which enables seeing. • All resistors are in Ω and 1/4 W or less unless otherwise
• Indication of transistor. specified.
• f : internal component.
C • C : panel designation.
Q These are omitted. Note: The components identified by mark 0 or dotted line
B E with mark 0 are critical for safety.
Replace only with part number specified.

Q • A : B+ Line.
• Voltages are taken with a VOM (Input impedance 10 MΩ).
B C E Voltage variations may be noted due to normal produc-
tion tolerances.
These are omitted. • Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J : CD PLAY

12
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

• Circuit Boards Location

PANEL (R) board

MAIN board

PANEL (L) board

TRAY SENSOR board

IN OUT SW board

BD board DRIVER board

MOTOR board
DISC SENSOR board

13
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

6-2. PRINTED WIRING BOARD – BD Section – • See page 13 for Circuit Boards Location.

(Page 18)
MAIN
A BOARD
CN301

M102
(SLED)

M101
(SPINDLE)

TP
(RFDC)

TP
(FEO)
TP (TEO)

TP
(DVC)

TP
(RFAC)
TP
(FEI)

• Semiconductor
Location
Ref. No. Location
D101 B-3

IC101 C-3
IC102 B-2
IC103 D-2

Q101 C-1 There are a few cases that the part printed on
Q102 A-3 this diagram isn’t mounted in this model.

14
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3
6-3. SCHEMATIC DIAGRAM – BD Section – • See page 22 for Waveforms. • See page 22 for IC Block Diagrams.

TP
(RFAC)

TP (FEI)
TP (DVC)

TP
(RFDC)

TP
(TEO)
IC B/D

IC B/D
TP
(FEO)

IC B/D

A
MAIN
BOARD
CN301
(Page 19)

Note: The components identified by mark 0 or dotted line • Voltages and waveforms are dc with respect to ground
with mark 0 are critical for safety. under no-signal conditions.
Replace only with part number specified. no mark : CD PLAY

15 15

Downloaded from www.Manualslib.com manuals search engine

 CDP-S3

6-4. PRINTED WIRING BOARDS – CD CHANGER Section – • See page 13 for Circuit Boards Location.

1 5

MAIN
BOARD
NO202
(Page 18)

There are a few cases that the part isn't mounted in model
is printed on diagrams.
16 16

Downloaded from www.Manualslib.com manuals search engine

 CDP-S3

6-5. SCHEMATIC DIAGRAM – CD CHANGER Section – • See page 22 for IC Block Diagram.

IC731
SUB TRAY1
HEIGHT SENSOR

IC732
SUB TRAY2
HEIGHT SENSOR

IC733
SUB TRAY3
HEIGHT SENSOR

B
MAIN
BOARD
NO202
(Page 19)

IC751
DISC IN
DETECT

• Voltages and waveforms are dc with respect to ground

under no-signal conditions.
no mark : CD STOP

17 17

Downloaded from www.Manualslib.com manuals search engine

 CDP-S3

6-6. PRINTED WIRING BOARD – MAIN Section – • See page 13 for Circuit Boards Location.

1 2 3 4 5 6 7 8 9 10
(Page 14) (Page 16)
BD BOARD DRIVER BOARD SYSTEM CONTROL 3
A CN101 B CN701 TO ST-S3/S5

MAIN BOARD
A C318 C316
CD303

C321 C118
FB305 1
JW158

JW137 FB314
IC503 C116
JW141

JW139

JW138
C319 C317 1 12 C532
CN301
C304

FB310 3
FB311
FB315 NO202 R484 R486
JW175

JW140
JW143

FB312 CLP102
L310
JW142

JW178
C303

R403
C302

(CHASSIS)

JW108
1 14
JW154

C523 1

JW112
JW111
JW110

JW109
CD311

JW130 C531 8
CD302

JW172

JW132
R440 C320 C311 R401
R437 C313 CD301 VCD101 CN102
JW151

1
JW135

C301

R426 R419 C251 R485 R487 2

JW102
B R429 1 8 C261 D514 D123

JW103
R436 R430

JW107
JW160
C315
FB313 IC402 R402
JW161 C255 C260
CN103
C314 C306
CD312

9
CD313

C310 C411 D515 SYSTEM CONTROL 5

JW155

JW159
R428 R424 D513 TO TC-S3
R417
JW120

CD304

JW129
JW163
JW128
JW127
JW126
JW125
JW156 R432
C401
JW157 R438 JW134

JW114
R413 JW136 C524

JW113
R443 C501
JW165 R411 JW133
C462 C425
C416 C522 IC502
R435

C427 JW122 14
JW145
JW144

JW124
JW153

R433 Q501 15
X401 C513
3
1 JW164 JW123
R460 R409 C521
JW162

R425 JW121
C CN401
R441 FB410 R445 JW171
R427
E
Q502
1
R482 R412 E
R442 R453 C499 L125
R456 C498 JW98 D504 C500
R134 D502 R123
IC401

JW100
R491
D511
R465 R494
R457 R451 C463 R489 C125
R469 R444
R500 R497 R483
R473 R447 R450 R448 JW99 CN101 C124

JW104
R492 JW106
R490 C122
JW131 D512 D503 D501
R477
IC102
JW169
JW168

JW148 9
3
C102
JW167

R481 FB416 C103

JW177
JW176

JW147 OPTICAL OUT

JW170
JW149

R132 JW119
TO ST-S3/S5
JW150

JW146 1
JW118
R493 R133
JW115

R480 JW117
R495 R496
D R452 R446 R449 R459
JW116 D105
C101 CLP101
C107 11
1
1-680-994- (21)

PANEL (L) BOARD

C NO703
(Page 20)

• Semiconductor Location
Ref. No. Location Ref. No. Location
D103 D-9 IC102 D-10
D104 D-9 IC401 C-4
D105 D-7 IC402 B-5
D123 B-8 IC502 C-8
D501 C-9 IC503 B-8
D502 C-9
D503 C-9 Q501 C-8
D504 C-9 Q502 C-8
D511 C-8
D512 D-7
D513 B-8
D514 B-8

18 18

Downloaded from www.Manualslib.com manuals search engine

 CDP-S3
6-7. SCHEMATIC DIAGRAM – MAIN Section – • See page 22 for Waveform.

OPTICAL OUT
TO ST-S3/S5

+3.3V
GND

SIG
CLP102
C122
CN301 IC102 0.022
21P TOTX140
PWM3 CD301 24 C103 C102 C101
0.1 0.1 0.1
C125 OPTICAL (CHASSIS)
PWM2 C301 0.47 50V CD302 26 220 D502 D501
TRANSCEIVER
10V 11ES2 11ES2
PWM1 C302 0.0047 CD303 28
C124 L125 D123
0.1 220µH MTZA-2.2A
DVDD C303 0.01 FB310 CD304 CN101
9P
DOUT C304 0.022 FB305 R123 100 D503 D504
D511
11ES2 11ES2 11ES2 C500 AC SYSTEM CONTROL 3
DGND FB311 C310 0.022 FB410 C501 0.1
4700 AC TO ST-S3/S5
LOUT 16V
Q501
HESO-GND
AGND FB312 RT1P137S
HESO-GND
ROUT
EVER+5V
AVDD FB313 Q501,502 D512
MRESET
11ES2
XRST C311 0.01 CD311 43 B+ SWITCH TP107
D105 V-MUTE
1SS133
DATA C320 0.01 CD312 35 C107 JW
D513 +5.6V REGULATOR I2C-DATA
(Page 15) XLT C313 220p CD313 42
Q502
BA1A4M
11ES2
O I I2C-CLK
CLOK C314 100p 37 C306 G
D514 D515
LDON C315 100p 40 C513 C524 C523 C522
11ES2 C521 11ES2
470 220 220 470 IC502
SQSO C316 100p A32 10V 10V 10V 10V TA78057S 0.1 CN102
8P
SENS C317 100p A36
DGND(TC)
JW98 JW99
SQCK C318 100p 33 100 100 VCD101
UNREG(TC)
SCOR C319 100p A19
MGND(TC)
MGND L310 5.6µH +7V REGULATOR
MGND(TC)
FB314
+7V O I
G SHASSIS GND
C321 C532 C116 1k
IC503 C531
0.022 FB315 470 TA7807S 0.1 VCD R-IN
10V
AGND(CD)
NO202 C118 1k
12P
VCD L-IN
DISC-SENS 52

IN-SW 47

OUT-SW C261 0.022 46

TRAYSENS3 C260 0.022 50

TRAYSENS2 49

TRAYSENS1 48 FB416

38

12

29

30
DGND

D+5V C255
0.022
(Page 17) LOD-POS 45

LOD-NEG 44 C463
10
MGND 50V
59

51

53

52

R133 75k
M+7V
C462

R134 1k
0.022
C251 R459 R451
R453 100

R452 100

0.022 100 100

R500 10k

R460 10k
77

73

69

65

TP463

TP461

TP460

TP458

TP457

TP456

R132
75k
R457 R456 CN103
10k 10k
15P
DGND

C401 91 BHALF
0.022
90 BSHUT
LED_
PLAY
LED_PLAY

LED_PLAY

LED_DISC3

LED_DISC3

LED_DISC3

LED_DISC3

LED_DISC2

LED_DISC2

LED_DISC2

LED_DISC2

LED_DISC1

LED_DISC1

LED_DISC1

LED_DISC1

VSS

SOFT-TEST

VCC

R/PB/PAS

A-TRIG

ECO CHECK

B-TRIG

DISC-SENS

LED_ 89 ASHUT
PLAY
A19

A32

A36

59 REC/PB/PAS
81 R450 100 50
LED_PAUSE T-SENS3 85 DATA-OUT
R449 100 49
R403 100

R402 100

R401 100

LED_PAUSE T-SENS2 84 DATA-IN

R484 R480 R448 100 48 SYSTEM CONTROL 5
100k LED_PAUSE T-SENS1 87 CLK
100 TO TC-S3
84 R447 100 47
EXP-IN DATA CLOSE 86 LAT
85 R485 100 R446 100 46
EXP-OUT DATA OPEN 94 KEY2
86 R486 100 R445 100 45
EXP-LAT LOAD-OUT 53 BTRIG
87 R487 100 R444 100 44
EXP-CLK LOAD-IN 51 ATRIG
R443 100 43
R489
LED_PAUSE XRST UNREG
89 100 R442 100 42
A-SHUT XLT MGND
LEVEL SHIFT
90 R490 100 R441 10k
IC402 B-SHUT SGND
SN74HCT04ANS 91 R491 100 SYSTEM CONTROLLER R440 100 40
-E05 B-HALF HOLD
IC401
R493 150 MODEL-IN M30620MAA-B31FP TP439
R492 4.7k R438 100 38
R482 10k TP493 KEY3 CD POWER
94 R494 100 R437 100 37
KEY2(TC) CD-CLK
95 R495 100 R436 100 36
KEY1(CD) SENS
19

32

36

R435 100 35
R483 10k AVSS CD-DATA
97 R497 100
KEY0(CD) RTS1
R433 100 33
VREF SQ-CLK
R496 10k SQ- R432 100 32
AVCC
BU PWM 2

BU PWM 1
BU PWM 3

DATA-IN
TP500
IIC-CLK

C498
CNVSS

RESET

X-OUT

SCOR

0.022
DATA
BYTE

X-IN
VSS

VCC

NMI

C499
IIC-

0.022

CN401
9P
R429 100

97 TP411
TP401

TP402

TP403

TP404

TP405

TP406

TP407

TP418

TP420

TP421

TP422

TP423

TP425

TP427

95
C425
R413 100p
330
R430
R481 150 81 100 R425 4.7k
X401 16MHz

R411 R417 R419 R424 R426 R428

R477 150 77 100 10k 100 2.2k 220k 100k R427 4.7k
12

R473 150 73 C427 100p

19

24

26

28

29

30

R409
R469 150 69 10k

(Page 21) R465 150 65

C411 C416
R412
1 10k 10
50V 50V

Note: The components identified by mark 0 or dotted line • Voltages and waveforms are dc with respect to ground
with mark 0 are critical for safety. under no-signal conditions.
Replace only with part number specified. no mark : CD PLAY
19 19

Downloaded from www.Manualslib.com manuals search engine

 CDP-S3

6-8. PRINTED WIRING BOARDS – PANEL Section – • See page 13 for Circuit Boards Location.

(Page 18)
MAIN BOARD
C CN401

PANEL (R) BOARD

9 1

NO703
R712

R711 R710

m REPEAT PLAY MODE

S712 S711 S707 S708

R706 R707

Z R705 R704
> .
S713 S714 (DISC 3)

Z Z
PANEL (L) BOARD (DISC 2) (DISC 1)
S706 S705 S704
R713 D703 D704 D705 1
D701 D702 2 NO701
DISC 3 DISC 2 DISC 1
D702, S717 NO702 1
R700 S701 R701 S702 R702 S703 R703
3 2 1 2
R715 N

S715 S716 R716 S717

x R714
D701, S716
X

11 11
1-680-995- (21) 1-680-996- (21)

20 20

Downloaded from www.Manualslib.com manuals search engine

 CDP-S3

6-9. SCHEMATIC DIAGRAM – PANEL Section –

R707 R706 R705 R704 R703 R702 R701 R700

1.8k 1.2k 1k 680 560 470 330 270

CN701
S708 S707 S706 S705 S704 S703 S702 S701
2P

PLAY MODE REPEAT DISC 1 DISC 2 DISC 3

(DISC 3) (DISC 2) (DISC 1)

R716 R715 R714 R713 R712 R711 R710

1.2k 1k 680 560 470 330 270

S717 S716 S715 S714 S713 S712 S711

CN702
2P

CNW703
9P

D701
SEL5923A

(Page 19)
D702
SEL5423E

D703
SEL5923A

D704
SEL5923A

D705
SEL5923A

21 21

Downloaded from www.Manualslib.com manuals search engine

 CDP-S3

• Waveforms • IC Block Diagrams

– BD Board – – MAIN Board – – BD Board –
1 IC101 ta (RFAC) (CD Play mode) qa IC401 qd (X-OUT)
IC101 CXD3017Q

AVDD3

AVDD0
AVSS3

AVSS0
DOUT

ASYO

RFDC
RFAC
CLTV

ADIO
IGEN
ASYI
BIAS
FILO
VDD

PCO
VSS

FILI

CE
TE
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41

1.1 Vp-p 2.6 Vp-p 40 SE

ERROR
DIGITAL 39 FE
CORRECTOR
DIGITAL ASYMMETRY 38 VC

INTERNAL BUS
OUT
PLL CORRECTOR
16K
RAM OPERATIONAL
LRCK 61 AMPLIFIER
D/A EFM ANALOG SWITCH
PCMD 62
INTERFACE DEMODULATOR
BCK 63 A/D
63 ns CONVERTER
EMPH 64
2 IC101 ra (TE) (CD Play mode)
XVDD 65
XTAI 66 TIMING
XTAO 67 LOGIC CLOCK
37 XTSL
XVSS 68 GENERATOR
36 TES1
AVDD1 69 35 TEST
AOUT1 70 SERVO DSP PWM GENERATOR
Approx. AIN1
34 VSS
71
0.4 Vp-p FOCUS FOCUS PWM 33 FRDR
SERVO GENERATOR 32 FFDR
TRACKING TRACKING 31 TRDR
LOUT1 72 SERVO PWM GENERATOR 30 TFDR
PWM PWM SUBCODE SLED SLED PWM 29 SRDR
AVSS1 73 PROCESSOR SERVO GENERATOR 28 SFDR
AVSS2 74
LOUT2 75 3rd ORDER 27 SSTP
NOISE SHAPER SERVO
INTERFACE 26 MDP
3 IC101 el (FE) (CD Play mode) DIGITAL
CLV 25 LOCK
AIN2 76 OVER SAMPLING
DIGITAL FILTER
AOUT2 77 SERVO AUTO MIRR, DFCT, 24 FOK
AVDD2 78 SEQUENCER FOK 23 DFCT
RMUT 79 DETECTOR 22 MIRR
SERIAL IN
Approx. LMUT 80 INTERFACE
0.3 Vp-p
CPU
INTERFACE 21 COUT

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20

GFS
SCLK

XLON

SCOR
XLAT

SENS

SPOB

C2PO
XRST
SYSM

WFCK
VDD
SQSO

ATSK

XUGF
SPOA

XPCK
SQCK

CLOK
DATA

4 IC101 wh (MDP)
IC102 BA5974FM-E2

CH3OUTR

CH4OUTR
CH3OUTF

CH4OUTF
POWVCC
CAPAIN3
CH4SIN'
PRFVCC

CH3RIN
CH4BIN

CH4SIN

CH3FIN

MUTE
GND

2.5 Vp-p
28 27 26 25 24 23 22 21 20 19 18 17 16 15

F R
R MUTE
INTERFACE

F
7.5 µs LEVEL SHIFT

THERMAL
SHUTDOWN
F
INTERFACE

F R F
R

INTERFACE
R
F R

1 2 3 4 5 6 7 8 9 10 11 12 13 14
VREFOUT

CH1FIN

CH1RIN

CAPAIN1

CH2FIN

CH2RIN

CAPAIN2

GND

VREFIN

POWVCC

CH2OUTR

CH2OUTF

CH1OUTR

CH1OUTF

22 22

Downloaded from www.Manualslib.com manuals search engine

 CDP-S3

– DRIVER Board –

IC103 CXA2581N-T4 IC701 BA6956AN

RW/ROM

30 DC OFST TSD
29 RFDCI
A –
–
B +
+ 28 RFDCO
C
DVC CONTROL LOGIC
D DVC
VCC
VC 1 2 3 4 5 6 7 8 9
–

VREF

OUT2

RNF

OUT1

VM

VCC

FIN

GND

RIN
DVC RW/ROM
+ VOFST 27 VC
VC

VC
LD 1 26 RFC
EQ 25 VFC
PD 2 APC AMP 24 BST

EQ ON/OFF
RFAC
EQ IN 3 23 RFG
RW/ROM VCA

RFAC VCC 22 VCC

AC SUM 4 SUMMING
AMP B VOFST 21 CEI
C –
–
GND 5 A +
+ 20 CE
D
A B C D
A DVC
A 6
B VC
B 7
C
C 8 RW/ROM
D
D 9 19 TE BAL
RW/ROM

E 10 GM
–
+ 18 TE

F 11 GM

VC
APC-OFF
(Hi-Z) RW/ROM
SW 12
RW/ROM RW/ROM
(H/L)
DVCC 13

B
VOFST 17 FEI
DVC
D –
–
DVC 14 A +
+ 16 FE
C
DVC
VC

RW/ROM
RFAC 15

23
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

6-10. IC PIN FUNCTION DESCRIPTION

• MAIN BOARD IC401 M30620MAA-B31FP (SYSTEM CONTROLLER)
Pin No. Pin Name I/O Description
1 to 7 — — Not used (open)
External data bus line byte selection signal input “L”: 16 bits, “H”: 8 bits
8 BYTE I
Not used (fixed at “L”)
9 CNVSS — To flash memory connector
10 — — Not used (fixed at “L”)
11 — — Not used (open)
12 RESET I Reset signal input from the tuner unit (ST-S3/S5)
13 X-OUT O System clock output terminal (16 MHz)
14 VSS — Ground terminal
15 X-IN I System clock input terminal (16 MHz)
16 VCC — Power supply terminal (+5V)
17 NMI I Non-maskable interrupt input terminal (fixed at “H” in this set)
18 — — Not used (open)
19 SCOR I Subcode sync (S0+S1) detection signal input from the CXD3017Q (IC101)
20 to 23 — — Not used (open)
24 BU PWM 3 O RFDC PWM signal output to the CXA2581N (IC103)
25 — — Not used (open)
26 BU PWM 2 O Tracking error PWM signal output to the CXA2581N (IC103)
27 — — Not used (open)
28 BU PWM 1 O Focus error PWM signal output to the CXA2581N (IC103)
Communication data reading clock signal input or transfer clock signal output with the tuner unit
29 IIC-CLK I/O
(ST-S3/S5)
30 IIC-DATA I/O Communication data bus with the tuner system (ST-S3/S5)
31 — — Not used
32 SQ-DATA-IN I Subcode Q data input from the CXD3017Q (IC101)
33 SQ-CLK O Subcode Q data reading clock signal output to the CXD3017Q (IC101)
34 RTS1 — Not used
35 CD-DATA O CD decode data output to the CXD3017Q (IC101)
36 SENS I Internal status (SENSE) signal input from the CXD3017Q (IC101)
37 CD-CLK O Serial data transfer clock signal output to the CXD3017Q (IC101)
Power on/off control signal output for the CD mechanism deck section
38 CD POWER O
“L”: standby, “H”: power on
39 — — Not used (open)
40 HOLD O Automatic power control hold signal output to the CXA2581N (IC103)
41 — — Not used (fixed at “L”)
42 XLT O Serial data latch pulse output to the CXD3017Q (IC101)
43 XRST O Reset signal output to the CXD3017Q (IC101)
44 LOAD-IN O Loading motor drive signal (load-in direction) output the motor driver (IC701)
45 LOAD-OUT O Loading motor drive signal (load-out direction) output the motor driver (IC701)
46 OPEN I Sub tray load in/out detect switch (S742) input “L”: sub tray is chucking position
47 CLOSE I Sub tray load in/out detect switch (S742) input “L”: sub tray slides out of chucking position
Detection input from the disc tray 1 height sensor (IC731)
48 T-SENS1 I
“H”: disc tray 1 position is chucking position
Detection input from the disc tray 2 height sensor (IC732)
49 T-SENS2 I
“H”: disc tray 2 position is chucking position

24
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

Pin No. Pin Name I/O Description

Detection input from the disc tray 3 height sensor (IC733)
50 T-SENS3 I
“H”: disc tray 3 position is chucking position
51 — — Not used (fixed at “H”)
52 DISC-SENS I Detection input from the disc in detect sensor (IC751)
Deck-B trigger plunger drive signal output to the tape deck unit (TC-S3)
53 B-TRIG O
“H”: trigger plunger on
54 ECO CHECK — Not used (fixed at “H”)
Deck-A trigger plunger drive signal output to the tape deck unit (TC-S3)
55 A-TRIG O
“H”: trigger plunger on
56 to 58 — — Not used (open)
Recording/playback/pass selection signal output to the tape deck unit (TC-S3)
59 R/PB/PASS O
“L”: recording, center voltage: playback, “H”: pass
60, 61 — — Not used (open)
62 VCC — Power supply terminal (+5V)
63 SOFT-TEST O For software check terminal
64 VSS — Ground terminal
65 to 68 LED_DISC1 O LED drive signal output of the 1 indicator (D705) “L”: LED on
69 to 72 LED_DISC2 O LED drive signal output of the 2 indicator (D704) “L”: LED on
73 to 76 LED_DISC3 O LED drive signal output of the 3 indicator (D703) “L”: LED on
77 to 80 LED_PLAY O LED drive signal output of the N indicator (D702) “L”: LED on
81 to 83 LED_PAUSE O LED drive signal output of the X indicator (D701) “L”: LED on
84 EXP-IN DATA I Serial data input from the tape deck unit (TC-S3)
85 EXP-OUT DATA O Serial data output to the tape deck unit (TC-S3)
86 EXP-LAT O Serial data latch pulse signal output to the tape deck unit (TC-S3)
87 EXP-CLK O Serial data transfer clock signal output to the tape deck unit (TC-S3)
88 LED_PAUSE O LED drive signal output of the X indicator (D701) “L”: LED on
89 A-SHUT I Shut off (desk-A) detection signal input from the tape deck unit (TC-S3)
90 B-SHUT I Shut off (desk-B) detection signal input from the tape deck unit (TC-S3)
Detection input from the deck-B cassette detect switch of the tape deck unit (TC-S3)
91 B-HALF I
“L”: cassette in
92 MODEL-IN I Model destination setting terminal
93 KEY3 — Not used (open)
94 KEY2 (TC) I Key input from the tape deck unit (TC-S3) (A/D input)
95 KEY1 (CD) I Key input terminal (A/D input) (S711 to S717) m, M , ., >, x, X, N keys input
96 AVSS — Ground terminal (for A/D conversion)
Key input terminal (A/D input) (S701 to S708) DISC 3, DISC 2, DISC 1, Z (DISC1), Z
97 KEY1 (CD) I
(DISC2), Z (DISC3), REPEAT, PLAY MODE keys input
98 VREF I Reference voltage (+5V) input terminal (for A/D converter)
99 AVCC — Power supply terminal (+5V) (for A/D conversion)
100 — — Not used (open)

25
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3
SECTION 7
EXPLODED VIEWS
NOTE:
• -XX and -X mean standardized parts, so they • Items marked “*” are not stocked since they The components identified by
may have some difference from the original are seldom required for routine service. Some mark 0 or dotted line with mark
one. delay should be anticipated when ordering 0 are critical for safety.
Replace only with part number
• Color Indication of Appearance Parts these items. specified.
Example: • The mechanical parts with no reference num-
KNOB, BALANCE (WHITE) . . . (RED) ber in the exploded views are not supplied.
↑ ↑
Parts Color Cabinet's Color

7-1. GENERAL SECTION

8
#2
10
7
9

11

7
not supplied
#1

CDM63B-30BD60
#1
not
1 supplied #1

5 12

not supplied
4
4 not supplied
6
#1 13
14
4 not supplied

2 not supplied

#1

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 X-4953-613-1 PANEL ASSY, FRONT 10 A-4725-658-A MAIN BOARD, COMPLETE
2 4-233-136-01 LID (CD) 11 1-757-633-11 CORD (WITH CONNECTOR) 17P
3 4-233-147-01 SPRING (CD) 12 4-233-135-01 PANEL, BACK (AEP, UK)
4 4-951-620-01 SCREW (2.6X8), +BVTP 12 4-233-135-11 PANEL, BACK (Korea, Australian)
5 1-680-996-11 PANEL (R) BOARD 12 4-233-135-31 PANEL, BACK (Mexican)

6 1-680-995-11 PANEL (L) BOARD 13 3-970-608-01 SUMITITE (B3), +BV

7 3-363-099-21 SCREW (CASE 3 TP2) 14 4-965-822-01 FOOT
8 4-233-134-11 COVER #1 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
9 1-823-055-11 WIRE (FLAT TYPE) (21 CORE) #2 7-685-871-01 SCREW +BVTT 3X6 (S)

26
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

7-2. CD MECHANISM DECK SECTION-1

(CDM63B-30BD60)

505
B
506
507 501
501
B
not supplied 506 519 508
501
509

not supplied

not supplied
510
A 501
518 not supplied
509
501 512
501
not
supplied
514 511
516

515 517 501

not supplied
504
513
520

501
503 501
502
not supplied not supplied
501
501
501

not supplied

501
not supplied
A
not supplied

501

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
501 4-218-253-01 SCREW (M2.6), +BTTP 511 4-228-964-01 SLIDER (STOCKER. R)
502 4-228-996-01 SPRING (R), TORSION 512 4-228-970-02 TRAY (SUB)
503 4-228-995-01 SPRING (L), TORSION 513 4-229-001-01 HOLDER (SENSOR)
504 4-228-972-02 TRAY (MAIN) 514 4-228-975-02 COVER (TRAY. L)
505 4-231-971-01 PULLEY (30B), CHUCKING 515 4-228-978-02 COVER (TRAY. R)

506 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING 516 4-228-970-12 TRAY (SUB)
507 4-228-414-01 BRACKET (YOKE) 517 4-228-970-22 TRAY (SUB)
508 4-228-980-01 SPRING (STOCKER), LEAF 518 X-4953-307-1 PULLEY (A) ASSY, CHUCKING
509 4-228-981-02 STOPPER (TRAY) 519 4-234-423-01 SPRING (STOCKER L), LEAF
510 4-228-963-01 SLIDER (STOCKER. L) 520 1-678-457-11 TRAY SENSOR BOARD

27
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

7-3. CD MECHANISM DECK SECTION-2

(CDM63B-30BD60)
563

567

580 574 553

575
BU-30BD60
561 561 561
556 560 553 556 579
565
562 560 551
553
561
558
560 551 A
559 564 569
562
568
551

not supplied 566

A
578
556
572
557 573 577
556 577
not supplied
555
557
576
578

not supplied 551

552 M721
554
571
553
551
551 570
552
556
551

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
551 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING 567 4-228-968-01 BELT
552 4-229-002-02 GEAR (SLIDER) 568 4-228-998-01 GEAR (DETECTION)
553 4-218-254-21 SCREW (M2.6), +PTPWH 569 4-228-976-01 SLIDER (BU. R)
554 4-228-971-01 CAM 570 1-678-461-11 MOTOR BOARD
555 4-228-974-02 RACK (CENTER) 571 X-4952-971-2 MOTOR ASSY

556 4-218-253-01 SCREW (M2.6), +BTTP 572 4-228-999-02 LEVER (MAIN. L)

557 4-228-969-02 SPRING (TABLE), LEAF 573 4-229-000-02 LEVER (MAIN. R)
558 4-228-977-01 SLIDER (BU. L) 574 4-227-899-01 SCREW (DIA. 12), FLOATING
559 4-951-620-01 SCREW (2.6X8), +BVTP 575 4-229-003-01 PULLEY
560 4-227-045-11 SPRING (INSULATOR), COIL 576 4-228-988-01 CHASSIS

561 4-231-451-01 INSULATOR (BU-30) 577 4-218-253-61 SCREW (M2.6), +BTTP

562 4-231-151-01 STOPPER (BU) 578 4-218-253-71 SCREW (M2.6), +BTTP
563 4-231-517-03 HOLDER (BU30) 579 1-678-462-11 IN OUT SW BOARD
564 4-228-985-01 GEAR (PULLEY) 580 1-678-463-11 DISC SENSOR BOARD
565 4-228-997-02 GEAR (CAM) M721 1-541-632-12 MOTOR, DC (LOADING)

566 1-678-460-11 DRIVER BOARD

28
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

7-4. BASE UNIT SECTION

(BU-30BD60)

604

606

not supplied

605
#5 #5

not supplied

not supplied
603

602

601

The components identified by mark 0 or dotted

line with mark 0 are critical for safety.
Replace only with part number specified.

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
601 3-531-576-11 RIVET 605 1-757-710-11 WIRE (FLAT TYPE) (16 CORE)
602 A-4725-531-A BD BOARD, COMPLETE 0 606 A-4735-188-A BU-30 (60) ASSY
603 4-233-832-01 GEAR (LB) #5 7-627-853-28 SCREW, PRECISION +P 2X3 TYPE3
604 4-233-831-01 GEAR (LA)

29
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3
SECTION 8
BD ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by
parts list may be different from the parts speci- are seldom required for routine service. mark 0 or dotted line with mark
fied in the diagrams or the components used Some delay should be anticipated when order- 0 are critical for safety.
Replace only with part number
on the set. ing these items. specified.
• -XX and -X mean standardized parts, so they • SEMICONDUCTORS
may have some difference from the original In each case, u: µ, for example: When indicating parts by reference
one. uA. . : µA. . uPA. . : µPA. . number, please include the board.
• RESISTORS uPB. . : µPB. . uPC. . : µPC. .
All resistors are in ohms. uPD. . : µPD. .
METAL: Metal-film resistor. • CAPACITORS
METAL OXIDE: Metal oxide-film resistor. uF: µF
F: nonflammable • COILS
uH: µH

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
A-4725-531-A BD BOARD, COMPLETE
******************* C191 1-124-584-00 ELECT 100uF 20% 10V
C192 1-163-038-11 CERAMIC CHIP 0.1uF 25V
< CAPACITOR > C193 1-104-665-11 ELECT 100uF 20% 10V
C194 1-163-038-11 CERAMIC CHIP 0.1uF 25V
C101 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V C195 1-163-038-11 CERAMIC CHIP 0.1uF 25V
C102 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C103 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C196 1-163-038-11 CERAMIC CHIP 0.1uF 25V
C104 1-162-962-11 CERAMIC CHIP 470PF 10% 50V C197 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C108 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C198 1-124-584-00 ELECT 100uF 20% 10V

C109 1-162-965-11 CERAMIC CHIP 0.0015uF 10% 50V < CONNECTOR >
C110 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V
C111 1-162-927-11 CERAMIC CHIP 100PF 5% 50V CN101 1-568-864-11 CONNECTOR, FFC 21P
C112 1-109-982-11 CERAMIC CHIP 1uF 10% 10V CN102 1-793-907-11 CONNECTOR, FFC/FPC 16P
C114 1-163-038-11 CERAMIC CHIP 0.1uF 25V
< DIODE >
C116 1-104-665-11 ELECT 100uF 20% 10V
C117 1-104-665-11 ELECT 100uF 20% 10V D101 8-719-422-12 DIODE UDZ-TE-17-3.9B
C118 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V
C121 1-163-038-11 CERAMIC CHIP 0.1uF 25V < FERRITE BEAD >
C122 1-124-584-00 ELECT 100uF 20% 10V
FB101 1-500-445-21 FERRITE 0uH
C123 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V FB102 1-500-445-21 FERRITE 0uH
C124 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V
C125 1-163-038-11 CERAMIC CHIP 0.1uF 25V < IC >
C126 1-163-038-11 CERAMIC CHIP 0.1uF 25V
C127 1-124-584-00 ELECT 100uF 20% 10V IC101 8-752-402-31 IC CXD3017Q
IC102 8-759-827-41 IC BA5974FM-E2
C129 1-162-974-11 CERAMIC CHIP 0.01uF 50V IC103 8-752-089-74 IC CXA2581N-T4
C130 1-163-038-11 CERAMIC CHIP 0.1uF 25V
C131 1-104-665-11 ELECT 100uF 20% 10V < SHORT >
C133 1-162-921-11 CERAMIC CHIP 33PF 5% 50V
C143 1-163-038-11 CERAMIC CHIP 0.1uF 25V JR101 1-216-295-11 SHORT 0
JR102 1-216-295-11 SHORT 0
C145 1-163-038-11 CERAMIC CHIP 0.1uF 25V JR103 1-216-295-11 SHORT 0
C153 1-163-038-11 CERAMIC CHIP 0.1uF 25V JR104 1-216-295-11 SHORT 0
C159 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V JR105 1-216-295-11 SHORT 0
C162 1-104-665-11 ELECT 100uF 20% 10V
C165 1-163-038-11 CERAMIC CHIP 0.1uF 25V JR106 1-216-295-11 SHORT 0
JR122 1-216-296-11 SHORT 0
C167 1-162-919-11 CERAMIC CHIP 22PF 5% 50V JR123 1-216-296-11 SHORT 0
C168 1-162-921-11 CERAMIC CHIP 33PF 5% 50V JR124 1-216-296-11 SHORT 0
C171 1-115-412-11 CERAMIC CHIP 680PF 5% 25V JR125 1-216-296-11 SHORT 0
C172 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C181 1-115-412-11 CERAMIC CHIP 680PF 5% 25V < COIL >

C182 1-162-927-11 CERAMIC CHIP 100PF 5% 50V L101 1-469-553-21 INDUCTOR 4.7uH
C183 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V
C184 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V < TRANSISTOR >
C185 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V
C190 1-115-156-11 CERAMIC CHIP 1uF 10V Q101 8-729-010-08 TRANSISTOR MSB710-RT1

30
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

BD DISC SENSOR DRIVER IN OUT SW MAIN

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
Q102 8-729-920-85 TRANSISTOR 2SD1664-T100-QR 1-678-463-11 DISC SENSOR BOARD
******************
< RESISTOR >
< PHOTO REFLECTOR >
R101 1-216-049-11 RES-CHIP 1K 5% 1/10W
R102 1-216-097-11 RES-CHIP 100K 5% 1/10W IC751 8-749-924-30 PHOTO REFLECTOR GP2S28
R103 1-216-077-00 RES-CHIP 15K 5% 1/10W (DISC IN DETECT)
R104 1-216-085-00 METAL CHIP 33K 5% 1/10W
R105 1-216-049-11 RES-CHIP 1K 5% 1/10W < RESISTOR >

R106 1-216-049-11 RES-CHIP 1K 5% 1/10W R751 1-249-407-11 CARBON 150 5% 1/4W

R107 1-216-073-00 METAL CHIP 10K 5% 1/10W **************************************************************
R108 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R109 1-216-121-11 RES-CHIP 1M 5% 1/10W 1-678-460-11 DRIVER BOARD
R111 1-216-099-00 METAL CHIP 120K 5% 1/10W *************

R114 1-218-745-11 RES-CHIP 160K 5% 1/16W < CAPACITOR >

R116 1-216-001-00 METAL CHIP 10 5% 1/10W
R117 1-216-049-11 RES-CHIP 1K 5% 1/10W C701 1-124-261-00 ELECT 10uF 20% 50V
R118 1-216-025-11 RES-CHIP 100 5% 1/10W C705 1-124-261-00 ELECT 10uF 20% 50V
R119 1-216-059-00 METAL CHIP 2.7K 5% 1/10W C706 1-164-159-11 CERAMIC 0.1uF 50V
C707 1-164-159-11 CERAMIC 0.1uF 50V
R120 1-216-077-00 RES-CHIP 15K 5% 1/10W
R122 1-216-097-11 RES-CHIP 100K 5% 1/10W < CONNECTOR >
R123 1-216-073-00 METAL CHIP 10K 5% 1/10W
R124 1-216-097-11 RES-CHIP 100K 5% 1/10W CN701 1-785-324-11 PIN, CONNECTOR (STRAIGHT) 12P
R131 1-216-033-00 METAL CHIP 220 5% 1/10W CN702 1-785-328-11 PIN, CONNECTOR (LIGHT ANGRE) 2P
CN703 1-785-331-11 PIN, CONNECTOR (LIGHT ANGLE) 5P
R143 1-216-085-00 METAL CHIP 33K 5% 1/10W CN704 1-785-329-11 PIN, CONNECTOR (LIGHT ANGLE) 3P
R144 1-216-085-00 METAL CHIP 33K 5% 1/10W CN705 1-785-329-21 PIN, CONNECTOR (LIGHT ANGLE) 3P
R147 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
R148 1-216-001-00 METAL CHIP 10 5% 1/10W < IC >
R149 1-216-001-00 METAL CHIP 10 5% 1/10W
IC701 8-759-598-69 IC BA6956AN
R158 1-216-083-00 METAL CHIP 27K 5% 1/10W
R159 1-216-083-00 METAL CHIP 27K 5% 1/10W < TRANSISTOR >
R162 1-216-097-11 RES-CHIP 100K 5% 1/10W
R171 1-216-081-00 METAL CHIP 22K 5% 1/10W Q701 8-729-029-66 TRANSISTOR RT1N141S-TP
R172 1-216-081-00 METAL CHIP 22K 5% 1/10W
< RESISTOR >
R173 1-216-081-00 METAL CHIP 22K 5% 1/10W
R181 1-216-081-00 METAL CHIP 22K 5% 1/10W R701 1-249-429-11 CARBON 10K 5% 1/4W
R182 1-216-081-00 METAL CHIP 22K 5% 1/10W R702 1-249-401-11 CARBON 47 5% 1/4W
R183 1-216-081-00 METAL CHIP 22K 5% 1/10W R705 1-249-435-11 CARBON 33K 5% 1/4W
R190 1-216-033-00 METAL CHIP 220 5% 1/10W R706 1-249-417-11 CARBON 1K 5% 1/4W
R707 1-249-429-11 CARBON 10K 5% 1/4W
R191 1-216-085-00 METAL CHIP 33K 5% 1/10W **************************************************************
R192 1-216-085-00 METAL CHIP 33K 5% 1/10W
R193 1-216-099-00 METAL CHIP 120K 5% 1/10W 1-678-462-11 IN OUT SW BOARD
R194 1-216-097-11 RES-CHIP 100K 5% 1/10W ****************
R195 1-216-113-00 METAL CHIP 470K 5% 1/10W
< SWITCH >
R196 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R198 1-216-295-11 SHORT 0 S741 1-771-821-11 SWITCH, PUSH (1 KEY) (IN)
S742 1-771-821-11 SWITCH, PUSH (1 KEY) (OUT)
< COMPOSITION CIRCUIT BLOCK > **************************************************************

RN101 1-233-576-11 RES, CHIP NETWORK 100 A-4725-658-A MAIN BOARD, COMPLETE
*********************
< VARIABLE RESISTOR >
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
RV101 1-238-602-11 RES, ADJ, CARBON 47K
< CAPACITOR/RESISTOR >
< VIBRATOR >
C101 1-164-159-11 CERAMIC 0.1uF 50V
X101 1-579-280-11 VIBRATOR, CRYSTAL (16.9344MHz) C102 1-164-159-11 CERAMIC 0.1uF 50V
************************************************************** C103 1-164-159-11 CERAMIC 0.1uF 50V
C116 1-249-417-11 CARBON 1K 5% 1/4W
C118 1-249-417-11 CARBON 1K 5% 1/4W

31
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

MAIN
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
D513 8-719-024-99 DIODE 11ES2-NTA2B
C122 1-161-494-00 CERAMIC 0.022uF 25V D514 8-719-024-99 DIODE 11ES2-NTA2B
C124 1-164-159-11 CERAMIC 0.1uF 50V
C125 1-126-923-11 ELECT 220uF 20% 10V D515 8-719-024-99 DIODE 11ES2-NTA2B
C251 1-161-494-00 CERAMIC 0.022uF 25V
C255 1-161-494-00 CERAMIC 0.022uF 25V < FERRITE BEAD >

C260 1-161-494-00 CERAMIC 0.022uF 25V FB305 1-412-473-21 INDUCTOR 0uH

C261 1-161-494-00 CERAMIC 0.022uF 25V FB310 1-412-473-21 INDUCTOR 0uH
C301 1-126-959-11 ELECT 0.47uF 20% 50V FB311 1-412-473-21 INDUCTOR 0uH
C302 1-162-600-11 CERAMIC 0.0047uF 20% 16V FB312 1-412-473-21 INDUCTOR 0uH
C303 1-162-306-11 CERAMIC 0.01uF 20% 16V FB313 1-412-473-21 INDUCTOR 0uH

C304 1-161-494-00 CERAMIC 0.022uF 25V FB314 1-412-473-21 INDUCTOR 0uH

C310 1-161-494-00 CERAMIC 0.022uF 25V FB315 1-412-473-21 INDUCTOR 0uH
C311 1-162-306-11 CERAMIC 0.01uF 20% 16V FB410 1-412-473-21 INDUCTOR 0uH
C313 1-162-286-31 CERAMIC 220PF 10% 50V FB416 1-412-473-21 INDUCTOR 0uH
C314 1-162-282-31 CERAMIC 100PF 10% 50V
< IC >
C315 1-162-282-31 CERAMIC 100PF 10% 50V
C316 1-162-282-31 CERAMIC 100PF 10% 50V IC102 8-749-019-13 IC TOTX140 (OPTICAL OUT TO ST-S3/S5)
C317 1-162-282-31 CERAMIC 100PF 10% 50V IC401 8-759-827-46 IC M30620MAA-B31FP
C318 1-162-282-31 CERAMIC 100PF 10% 50V IC402 8-759-269-09 IC SN74HCT04ANS-E05
C319 1-162-282-31 CERAMIC 100PF 10% 50V IC502 8-759-158-62 IC TA78057S
IC503 8-759-071-48 IC TA7807S
C320 1-162-306-11 CERAMIC 0.01uF 20% 16V
C321 1-161-494-00 CERAMIC 0.022uF 25V < RESISTOR >
C401 1-161-494-00 CERAMIC 0.022uF 25V
C411 1-126-960-11 ELECT 1uF 20% 50V JW98 1-247-807-31 CARBON 100 5% 1/4W
C416 1-126-964-11 ELECT 10uF 20% 50V JW99 1-247-807-31 CARBON 100 5% 1/4W

C425 1-162-282-31 CERAMIC 100PF 10% 50V < COIL >

C427 1-162-282-31 CERAMIC 100PF 10% 50V
C462 1-161-494-00 CERAMIC 0.022uF 25V L125 1-410-336-11 INDUCTOR 220uH
C463 1-126-964-11 ELECT 10uF 20% 50V L310 1-410-467-11 INDUCTOR 5.6uH
C498 1-161-494-00 CERAMIC 0.022uF 25V
< TRANSISTOR >
C499 1-161-494-00 CERAMIC 0.022uF 25V
C500 1-164-159-11 CERAMIC 0.1uF 50V Q501 8-729-049-79 TRANSISTOR RT1P137S-TP
C501 1-126-937-11 ELECT 4700uF 20% 16V Q502 8-729-900-80 TRANSISTOR BA1A4M-TP
C513 1-126-935-11 ELECT 470uF 20% 10V
C521 1-164-159-11 CERAMIC 0.1uF 50V < RESISTOR >

C522 1-126-935-11 ELECT 470uF 20% 10V R123 1-247-807-31 CARBON 100 5% 1/4W
C523 1-126-934-11 ELECT 220uF 20% 10V R132 1-247-876-11 CARBON 75K 5% 1/4W
C524 1-126-934-11 ELECT 220uF 20% 10V R133 1-247-876-11 CARBON 75K 5% 1/4W
C531 1-164-159-11 CERAMIC 0.1uF 50V R134 1-249-417-11 CARBON 1K 5% 1/4W
C532 1-126-935-11 ELECT 470uF 20% 10V R401 1-247-807-31 CARBON 100 5% 1/4W

< CONNECTOR > R402 1-247-807-31 CARBON 100 5% 1/4W

R403 1-247-807-31 CARBON 100 5% 1/4W
* CN101 1-568-419-11 PIN, CONNECTOR 9P R409 1-249-429-11 CARBON 10K 5% 1/4W
CN102 1-568-373-11 PIN, CONNECTOR 8P R411 1-247-807-31 CARBON 100 5% 1/4W
CN103 1-566-859-11 SOCKET, CONNECTOR 15P R412 1-249-429-11 CARBON 10K 5% 1/4W
(SYSTEM CONTROL 5 TO TC-S3)
CN301 1-568-838-11 CONNECTOR, FFC 21P R413 1-249-411-11 CARBON 330 5% 1/4W
* CN401 1-568-936-11 PIN, CONNECTOR 9P R417 1-249-429-11 CARBON 10K 5% 1/4W
R419 1-247-807-31 CARBON 100 5% 1/4W
< DIODE > R424 1-249-421-11 CARBON 2.2K 5% 1/4W
R425 1-249-425-11 CARBON 4.7K 5% 1/4W
D105 8-719-911-19 DIODE 1SS133T-72
D123 8-719-982-96 DIODE MTZJ-T-72-2.2A R426 1-247-887-00 CARBON 220K 5% 1/4W
D501 8-719-024-99 DIODE 11ES2-NTA2B R427 1-249-425-11 CARBON 4.7K 5% 1/4W
D502 8-719-024-99 DIODE 11ES2-NTA2B R428 1-249-441-11 CARBON 100K 5% 1/4W
D503 8-719-024-99 DIODE 11ES2-NTA2B R429 1-247-807-31 CARBON 100 5% 1/4W
R430 1-247-807-31 CARBON 100 5% 1/4W
D504 8-719-024-99 DIODE 11ES2-NTA2B
D511 8-719-024-99 DIODE 11ES2-NTA2B R432 1-247-807-31 CARBON 100 5% 1/4W
D512 8-719-024-99 DIODE 11ES2-NTA2B R433 1-247-807-31 CARBON 100 5% 1/4W

32
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

MAIN MOTOR PANEL (L) PANEL (R) TRAY SENSOR

Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
R435 1-247-807-31 CARBON 100 5% 1/4W 1-680-995-11 PANEL (L) BOARD
R436 1-247-807-31 CARBON 100 5% 1/4W ***************
R437 1-247-807-31 CARBON 100 5% 1/4W
< LED >
R438 1-247-807-31 CARBON 100 5% 1/4W
R440 1-247-807-31 CARBON 100 5% 1/4W D701 8-719-057-97 LED SEL5923A-TP15 (X)
R441 1-249-429-11 CARBON 10K 5% 1/4W D702 8-719-058-03 LED SEL5423E-TP15 (N)
R442 1-247-807-31 CARBON 100 5% 1/4W D703 8-719-057-97 LED SEL5923A-TP15 (3)
R443 1-247-807-31 CARBON 100 5% 1/4W D704 8-719-057-97 LED SEL5923A-TP15 (2)
D705 8-719-057-97 LED SEL5923A-TP15 (1)
R444 1-247-807-31 CARBON 100 5% 1/4W
R445 1-247-807-31 CARBON 100 5% 1/4W < RESISTOR >
R446 1-247-807-31 CARBON 100 5% 1/4W
R447 1-247-807-31 CARBON 100 5% 1/4W R710 1-249-410-11 CARBON 270 5% 1/4W
R448 1-247-807-31 CARBON 100 5% 1/4W R711 1-249-411-11 CARBON 330 5% 1/4W
R712 1-249-413-11 CARBON 470 5% 1/4W
R449 1-247-807-31 CARBON 100 5% 1/4W R713 1-249-414-11 CARBON 560 5% 1/4W
R450 1-247-807-31 CARBON 100 5% 1/4W R714 1-249-415-11 CARBON 680 5% 1/4W
R451 1-247-807-31 CARBON 100 5% 1/4W
R452 1-247-807-31 CARBON 100 5% 1/4W R715 1-249-417-11 CARBON 1K 5% 1/4W
R453 1-247-807-31 CARBON 100 5% 1/4W R716 1-249-418-11 CARBON 1.2K 5% 1/4W

R456 1-249-429-11 CARBON 10K 5% 1/4W < SWITCH >

R457 1-249-429-11 CARBON 10K 5% 1/4W
R459 1-247-807-31 CARBON 100 5% 1/4W S711 1-771-410-21 SWITCH, TACTILE (m)
R460 1-249-429-11 CARBON 10K 5% 1/4W S712 1-771-410-21 SWITCH, TACTILE (M)
R465 1-249-407-11 CARBON 150 5% 1/4W S713 1-771-410-21 SWITCH, TACTILE (>)
S714 1-771-410-21 SWITCH, TACTILE (.)
R469 1-249-407-11 CARBON 150 5% 1/4W S715 1-771-410-21 SWITCH, TACTILE (x)
R473 1-249-407-11 CARBON 150 5% 1/4W
R477 1-249-407-11 CARBON 150 5% 1/4W S716 1-771-410-21 SWITCH, TACTILE (X)
R480 1-249-441-11 CARBON 100K 5% 1/4W S717 1-771-410-21 SWITCH, TACTILE (N)
R481 1-249-407-11 CARBON 150 5% 1/4W **************************************************************

R482 1-249-429-11 CARBON 10K 5% 1/4W 1-680-996-11 PANEL (R) BOARD

R483 1-249-429-11 CARBON 10K 5% 1/4W ***************
R484 1-247-807-31 CARBON 100 5% 1/4W
R485 1-247-807-31 CARBON 100 5% 1/4W < RESISTOR >
R486 1-247-807-31 CARBON 100 5% 1/4W
R700 1-249-410-11 CARBON 270 5% 1/4W
R487 1-247-807-31 CARBON 100 5% 1/4W R701 1-249-411-11 CARBON 330 5% 1/4W
R489 1-247-807-31 CARBON 100 5% 1/4W R702 1-249-413-11 CARBON 470 5% 1/4W
R490 1-247-807-31 CARBON 100 5% 1/4W R703 1-249-414-11 CARBON 560 5% 1/4W
R491 1-247-807-31 CARBON 100 5% 1/4W R704 1-249-415-11 CARBON 680 5% 1/4W
R492 1-249-425-11 CARBON 4.7K 5% 1/4W
R705 1-249-417-11 CARBON 1K 5% 1/4W
R493 1-249-407-11 CARBON 150 5% 1/4W R706 1-249-418-11 CARBON 1.2K 5% 1/4W
R494 1-247-807-31 CARBON 100 5% 1/4W R707 1-249-420-11 CARBON 1.8K 5% 1/4W
R495 1-247-807-31 CARBON 100 5% 1/4W
R496 1-249-429-11 CARBON 10K 5% 1/4W < SWITCH >
R497 1-247-807-31 CARBON 100 5% 1/4W
S701 1-771-410-21 SWITCH, TACTILE (DISC 3)
R500 1-249-429-11 CARBON 10K 5% 1/4W S702 1-771-410-21 SWITCH, TACTILE (DISC 2)
S703 1-771-410-21 SWITCH, TACTILE (DISC1)
< VIBRATOR > S704 1-771-410-21 SWITCH, TACTILE (Z (DISC 1))
S705 1-771-410-21 SWITCH, TACTILE (Z (DISC 2))
X401 1-781-107-21 VIBRATOR, CERAMIC (16MHz)
************************************************************** S706 1-771-410-21 SWITCH, TACTILE (Z (DISC 3))
S707 1-771-410-21 SWITCH, TACTILE (REPEAT)
1-678-461-11 MOTOR BOARD S708 1-771-410-21 SWITCH, TACTILE (PLAY MODE)
************* **************************************************************

< CAPACITOR > 1-678-457-11 TRAY SENSOR BOARD

******************
C721 1-162-306-11 CERAMIC 0.01uF 30% 16V
************************************************************** < CAPACITOR >

C731 1-164-159-11 CERAMIC 0.1uF 50V

33
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

TRAY SENSOR
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
< PHOTO SENSOR >

IC731 8-749-081-01 PHOTO SENSOR DG-264

IC732 8-749-081-01 PHOTO SENSOR DG-264
IC733 8-749-081-01 PHOTO SENSOR DG-264

< RESISTOR >

R731 1-247-876-11 CARBON 75K 5% 1/4W

R732 1-249-408-11 CARBON 180 5% 1/4W
R733 1-247-876-11 CARBON 75K 5% 1/4W
R734 1-249-408-11 CARBON 180 5% 1/4W
R735 1-247-876-11 CARBON 75K 5% 1/4W

R736 1-249-408-11 CARBON 180 5% 1/4W

***********************************************************

MISCELLANEOUS
**************

9 1-823-055-11 WIRE (FLAT TYPE) (21 CORE)

11 1-757-633-11 CORD (WITH CONNECTOR) 17P
571 X-4952-971-2 MOTOR ASSY
605 1-757-710-11 WIRE (FLAT TYPE) (16 CORE)
0 606 A-4735-188-A BU-30 (60) ASSY

M721 1-541-632-12 MOTOR, DC (LOADING)

The components identified by mark 0 or dotted

line with mark 0 are critical for safety.
Replace only with part number specified.
34
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

MEMO

35
Downloaded from www.Manualslib.com manuals search engine
 CDP-S3

REVISION HISTORY

Clicking the version allows you to jump to the revised page.

Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.

Ver. Date Description of Revision

1.0 2001.04 New

Downloaded from www.Manualslib.com manuals search engine