Doc.

Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 1 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

Operation Manual

ST340UR

Suntech International Ltd.

CONFIDENTIAL DOCUMENT
This document belongs to intellectual property of Suntech
International Ltd. and shall neither be copied nor be given to any
3rd partie(s) without prior written consent from the company.
DO NOT MAKE ANY COPIES

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 2 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

Table of Contents

1. Introduction ........................................................................................................................................ 6
2. Overview ............................................................................................................................................. 7
2-1. Operation modes ......................................................................................................................... 7
2-2. Reports sent by device................................................................................................................ 7
2-3. Parameter change........................................................................................................................ 8
2-4. Features ....................................................................................................................................... 8
3. Communication string format ......................................................................................................... 10
3-1. Command format ....................................................................................................................... 10
3-2. Report format ............................................................................................................................. 11
4. Configuration ................................................................................................................................... 12
4-1. Network parameters .................................................................................................................. 13
4-2. Reporting parameters ............................................................................................................... 14
4-3. Event parameters....................................................................................................................... 16
4-4. GSM parameters for SMS messaging / phone Calling ............................................................ 19
4-5. Parameters for various features ............................................................................................... 20
4-6. Vehicle battery parameters ....................................................................................................... 22
4-7. Motion sensor parameters ........................................................................................................ 23
4-8. Circular geo-fencing parameters .............................................................................................. 24
4-9. Additional parameters (TCP/UDP parameters) ........................................................................ 25
4-10. Additional parameters2 ........................................................................................................... 28
4-11. New parameters ....................................................................................................................... 29
4-12. Backup battery parameters ..................................................................................................... 32
4-13. Telemetry parameters.............................................................................................................. 33
4-14. Setting for Driver ID parameters ............................................................................................. 34
4-14-1. ADD Driver ID ........................................................................................................................................ 34
4-14-2. Remove Driver ID .................................................................................................................................. 34
4-14-3. Get Drive ID............................................................................................................................................ 35
4-15. Driver Pattern Analysis parameters ....................................................................................... 36
5. Reporting to Server.......................................................................................................................... 37
5-1. Status Report ............................................................................................................................. 38
5-1-1. Normal ...................................................................................................................................................... 38
5-1-2. Zip ............................................................................................................................................................. 39
5-2. Emergency Report ..................................................................................................................... 42
5-2-1. Normal ...................................................................................................................................................... 42
5-2-2. Zip ............................................................................................................................................................. 43
5-3. Event Report .............................................................................................................................. 46
5-3-1. Normal ...................................................................................................................................................... 46
5-3-2. Zip ............................................................................................................................................................. 47
5-4. Alert Report ................................................................................................................................ 49
5-4-1. Normal ...................................................................................................................................................... 49
5-4-2. Zip ............................................................................................................................................................. 52
5-5. Travel Event Report ................................................................................................................... 55
5-5-1. Normal ...................................................................................................................................................... 55
5-5-2. Zip ............................................................................................................................................................. 56
5-6. Keep-Alive Report...................................................................................................................... 58
5-6-1. Normal ...................................................................................................................................................... 58
Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 3 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

5-6-2. Zip ............................................................................................................................................................. 58

5-7.Data Report from External RS232 .............................................................................................. 59
5-7-1. Normal ...................................................................................................................................................... 59
5-7-2. Zip ............................................................................................................................................................. 60
5-8. Transferring Data to External RS232 Device ........................................................................... 62
5-9. Status String Reporting via SMS .............................................................................................. 63
5-9-1. In case of Back-up method .................................................................................................................... 63
5-9-2. In case of Main method .......................................................................................................................... 63
5-10. Location query sent via smart phone..................................................................................... 64
6. Command for general use ............................................................................................................... 65
6-1. Common parts of this command .............................................................................................. 65
6-2. Requesting Status ..................................................................................................................... 65
6-3. Pre-setting .................................................................................................................................. 66
6-4. ACK of Emergency .................................................................................................................... 68
6-5. Re-setting (Restoring to factory defaults and Rebooting) ...................................................... 68
6-6. Enable1 (‘Activating Output 1’) ................................................................................................. 69
6-7. Disable1 (‘Inactivating Output1’) .............................................................................................. 69
6-8. Requesting IMSI ......................................................................................................................... 69
6-9. Requesting ICCID ...................................................................................................................... 70
6-10. Requesting IMEI ....................................................................................................................... 70
6-11. Requesting Version ................................................................................................................. 70
6-12Status Request made by External device connected with RS232 of Event Lines ................. 71
6-13 AT Commands from RS232 ...................................................................................................... 71
7. Command for non-general use ....................................................................................................... 72
7-1. Erase All ..................................................................................................................................... 72
7-2. Initialize Traveled Distance ....................................................................................................... 72
7-3. Setting Traveled Distance ......................................................................................................... 73
7-4. Initializing Message Number ..................................................................................................... 73
7-5. Setting Hour-Meter .................................................................................................................... 73
7-6. Initialize Circular Geo-fence ...................................................................................................... 73
7-7. Requesting Circular Geo-fence ................................................................................................ 74
7-8. Requesting Own Phone Number .............................................................................................. 74
7-9. Setting Own Phone Number ..................................................................................................... 75
7-10. Command to Reboot ............................................................................................................... 75
7-11. Setting ImproveBatteryLife ..................................................................................................... 75
7-12. Request ImproveBatteryLife ................................................................................................... 76
7-13. Command on How to Restart Anti-Theft 2 ............................................................................. 76
7-14. Command on How to Set SMS Number for Panic Situation ................................................. 76
7-15. Requesting SMS Number Used in Panic Situation ................................................................ 76
7-16. Command to Set Google Map Address .................................................................................. 77
7-17. Command to Get Google Map Address.................................................................................. 77
7-18. Changing Direction of SMS response .................................................................................... 78
7-19. Requesting Direction of SMS response ................................................................................. 78
7-20. Request Driver ID..................................................................................................................... 78
7-21. Release Output Control by Driver ID ...................................................................................... 79
7-22. Start DPA Calibration .............................................................................................................. 79
7-23. Stop DPA Calibration............................................................................................................... 79
7-24. Testing Output 1 for 30 seconds. ........................................................................................... 80
7-25. Testing Output 1 for 60 seconds. ........................................................................................... 80

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 4 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

8. Detailed Description on Event Lines and Features ....................................................................... 81

8-1. Total 8 pin Event Lines .............................................................................................................. 81
8-1-1. Immobilizer .............................................................................................................................................. 81
8-1-2. Immobilizer2 ............................................................................................................................................ 82
8-1-3. Alert of Buzzer ......................................................................................................................................... 83
8-2. Indication with Two (2) LEDs .................................................................................................... 84
8-2-1. Red LED for GPS ..................................................................................................................................... 84
8-2-2. Blue LED for GPRS ................................................................................................................................. 84
8-3. Power Saving ............................................................................................................................. 86
8-4. Backup Battery .......................................................................................................................... 87
8-5. Motion Sensor............................................................................................................................ 88
8-6. Protection of Vehicle Battery .................................................................................................... 89
8-7. Anti-Theft ................................................................................................................................... 90
8-8. Storage of Reports un-sent ....................................................................................................... 93
8-9. I-button ....................................................................................................................................... 94
8-10. Driver Pattern Calibration ....................................................................................................... 94
8-11. Over-speed ............................................................................................................................... 95
9. Engineering Command .................................................................................................................... 96
9-1. Command on how to shutdown back-up battery .................................................................... 96
9-2. Command on how to stop shutdown back-up battery ............................................................ 96
Revisions .............................................................................................................................................. 97

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 5 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

Disclaimer
We, at Suntech, announce that this document and all other related products (i.e. device, firmware, and software)
have been developed by the company, Suntech International Ltd., which is hereinafter referred to as “Suntech”.
The information in this manual is believed to be accurate and reliable at the time of releasing. We, at Suntech, also
assume no responsibility for any damage or loss resulting from the use of this manual, and expressly disclaim any
liability or damages for loss of data, loss of use, and property damage of any kind, direct, incidental or
consequential, in regard to or arising out of the performance or form of the materials presented herein or in any
software program(s) that may accompany this document. When this document is released, it is most compatible
with a specified firmware version. Now that the functionalities of the devices are being developed and improved
continuously from time to time by Suntech, any alteration on the protocol, the firmware functions, the hardware
specifications of the product is subject to change without prior notice.

Copyright
We, at Suntech, notify that Suntech holds all parts of intellectual rights applicable in the copyright laws in all the
countries. The information contained in this document cannot be reproduced in any form without prior written
consent made by Suntech. Any software programs that might accompany this document can be used only in
accordance with any license agreement(s) between the purchaser and Suntech.

Warning
Our customers are required to be aware that connecting the wire inputs can be hazardous to both of the installer
and your vehicle’s electrical system(s) if not done by an experienced installer. This document assumes you are
aware of the inherent dangers of working in installing the device on the vehicle(s) and the machinery.

Document Amendments

Please be advised that, for the firmware version column with specific firmware number, any modification(s) on the
comments column should be done on this corresponding firmware version (and the versions thereafter). Please
make sure you upgrade the firmware to the specified version before applying any changes made in this protocol.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 6 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

1. Introduction

The ST300 is a vehicle tracking and controlling device. It is designed to collect location data through GPS
technology, various vehicle conditions through event lines, and interact remotely with its server by using
GSM/GPRS technology.

In order to make the vehicle tracking system work, device should be configured and installed properly on a vehicle
whose geographical position and/or state is desired to be remotely monitored and/or controlled.

Following this “Introduction Chapter” (i.e. Chapter 1.), the Operation Manual is organized as below.

 Chapter 2. Overview

This chapter covers fundamental features of the device.

 Chapter 3. Communication string format (‘Command’ and ‘Report’)

This chapter gives descriptions on the two (2) formats, Command (all the formats received by device) and Report
(sent from the device).

 Chapter 4. Configuration

This chapter gives users explanation on how and what parameters are required to be set in configuring
device.

This manual describes setting commands which can be sent with following three options;
- Option 1 : Setting by PC
- Option 2 : Setting by GPRS
- Option 3 : Setting by SMS

Practically special program (named as “SyncTrack”) is used for setting. It enables setting much easier
and multi-setting possible in PC environments.

 Chapter 5. Reporting to server

This chapter covers when and what reports are sent back to the server by device.

 Chapter 6. Checking/Changing the current settings

This chapter describes how user can check current settings of the device and how user can change the ‘pre-
defined’ parameters.

 Chapter 7. Detailed description on event lines and special features

This chapter gives users detailed information on key features of the device and on how to operate the device if the
events occur after configuring the parameters related to such events.

Please note that this ‘Operation Manual’ is for a standard model. In case specific requirements are incorporated
into this manual, such a manual applies only for the case.

For overall operation including installation, in addition to the ‘Operation Manual’, users should refer to other
documents such as Installation Manual, Technical Data Sheet, Firmware OTA (over-the-air) Manual, Buyer Change
Guide, Trace Log, Assembly Guide and so on.
Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 7 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

2. Overview
Main function of device installed on a vehicle is to report vehicle location and status to its monitoring server at pre-
defined interval and to deliver command coming from the server for activating any appliance connected to the
device.

2-1. Operation modes

The device works in one of the three (3) operation modes below.

 Driving mode:

This mode starts when ‘Ignition’ of the vehicle is ON.

 Parking mode:

This mode is operational when ‘Ignition’ is OFF for duration longer than the pre-defined time (‘T1’).

In parking mode, the device can get into special modes for power saving like ‘Sleep mode’ and ‘Deep
sleep mode’. These power saving modes are described in more details in this document.

 Emergency mode:

This mode works either when panic button is ON or when one of any pre-defined events occurs.

2-2. Reports sent by device

There are 8types of report/ response sent by device to the server as follows:

 Status report (made in string / made in zip),

 Status string report (made in string) sent via SMS

 Emergency report,

 Event report,

 Keep-alive report,

 Alert (**),

Note (**): In addition to the reports periodically sent to the server as described above, device also sends
some alerts. For instance, device sends the server such an alert if the vehicle moves under the parking
mode or if the connected Input Line is changed.

Suntech can also increase this capacity up to a certain level if a customer of the device wants to do so. As soon as
the reporting condition for the device is recovered, the device starts sending all those accumulated reports
according to the following rule:
Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 8 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

- Emergency (the most important)  Command Response  Alert  Status Report Alive (the lowest priority)

This means that the emergency report is the first one that should be sent right after the GPRS network condition is
recovered.

2-3. Parameter change

Parameters which have already been set on the device can be changed via GPRS or via SMS or via RS232
connected with PC if a user needs to do so. Some controlling functions can also be implemented in the same way.

How to change values of the current parameters is described in detail in Chapter 4 of this document.

2-4. Features

Key features of the ST340UR device are as follows:

- Power Saving Modes( = Power Down Modes)

- LED Indicators

The LEDs indicate GPRS and GPS status. It is helpful to check what error(s) and why such an error has
occurred.

- Event Lines

Device has RS232 (TX/RX), 1-wire, 1 output line and 2 input lines, being 1 input can be configurable as
ignition line.

- Upgrading Firmware by Over The Air (Firmware OTA)

In case ‘firmware’ of the device has an (some) error(s) or needs to be upgraded to provide the user with
newly implemented services, the device can upgrade its internal ROM file by over the air (Firmware OTA),
remotely via GPRS. The users do not need to visit the vehicle individually to download the new firmware on
those vehicles.
How to do OTA is described in detail in the “SunTech_OTA_UA_Protocol” document.

- Parking Lock

Device is able to check if the vehicle moves away from the pre-defined parking boundary or starts moving
without having a mode of the ignition on. In case the device recognizes such an unauthorized moving or
driving, it sends an emergency report immediately.

- Over speed

Device checks speed of the vehicle and sends to the server an alert if the vehicle runs faster than the pre-
defined over-speed threshold values.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 9 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

- Checking Status of Main Power Source

Device recognizes its connectivity with the main power source (i.e. vehicle’s battery) and is able to inform
the server about status on whether or not the main power line is disconnected. The device is also able to
inform the server about the voltage level status of the main power source and informs the server in case the
voltage level of the main power source drops down below the pre-set value. This function is applicable to
battery-installed device models only.

- Alerting Battery Error

Device sends an alert when a battery charging error occurs. This function is applicable only to the device
models available with back-up battery.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 10 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

3. Communication string format

All the communication messages exchanged between device and its server should be in the form of STRING as
described below. Each ‘Report’ can be compressed in ZIP. Every ‘Filed’ is separated with semicolon. All the report
string triggered by device ends with a mark, ‘＼r’ (0x0d).

3-1. Command format

The following format is used when the server sends command message to the device(s) as shown in the below
table. The “Value”(or Indicating Mark) and its “Meaning” are described individually.

The parts consisting of ‘Fields’ are capitalized for naming like:

“HDR” stands for the header, ‘DEV_ID’ for device’ identification number, “VER” for version, Field 1, Field 2, etc.

HDR DEV_ID VER Field 1 Field 2 … Field n

Field Value (or Mark) Meaning

HDR String “ST300” + Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version. This is fixed with “02”.
Field 1 ~ n String Contents

The ‘Device ID’ is a unique number that each device should have. It is equal to the last 9 digits of IMEI numbers
shown on the back label of the device. Whenever the server sends a command message, it designates a specific
device along with the unique identification number of the device as a command receiver. And then, the device
recognizes a fact that it has received the command message and responds to the server with a relevant response
or a relevant action to be taken. This is how a normal communication is made between the server and its device.

On the other hand, sometimes, a very bad GPRS connection between a device and the server may consequently
bring about a bad result that the specified command message would be delivered NOT to the targeted device BUT
to other device. In such a situation, the wrong device does not accept the command message because the device
ID number of the message does not match the ID number of the wrong device.

However, we might consider a situation in which a command message is delivered to a device via RS232. In such
a situation the device accepts the command message even though the device ID number of that command
message is NOT its own one.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 11 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

3-2. Report format

The contents of the following table show what messages and how they are delivered to the server in response to
the command that the server has sent to the device(s) by requesting the device(s) to respond with.

HDR DEV_ID SW_VER Field 1 Field 2 … Field n

Field Value (or Mark) Meaning

HDR String “ST300” + Report type
DEV_ID 9 char. Device ID
SW_VER “001” Software version that the device has.
Field 1 ~ n String Contents

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 12 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4. Configuration

Before a device starts being operated, its parameters should be set first. This chapter shows the string to be sent to
device.

There are 3 options of sending string.

Option 1: by using PC
Option 2: by using GSM/GPRS network
Option 3: by messaging via SMS

In practice, configuration can be made more efficiently with ‘SyncTrak’, i.e. a setting tool provided by Suntech.

Once a device receives a command from the server, it gets back to the server with a relevant response. Device
also changes some parameters (if it is required to do so) or takes an action as instructed below as per the
command sent by the server.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 13 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-1. Network parameters

The following table shows how and what parameters are required to be set so that the device can be connected
with network. As shown in the bottom part of this table, an ‘<Example>’ of ‘[command]’ and ‘[response]’are made in
string respectively when the configuration for the networking is completed.

HDR DEV_ID VER AUTH APN USER_ID USER_PWD SEVER_IP SEVER_PORT

B_SEVER_IP B_SEVER_PORT SMS_NO PIN_NO

Field Marks Value Meaning

HDR “ST300NTW” Command type of Header
DEV_ID 9 char. Device ID
VER “02” Protocol Version
AUTH ‘0’ /‘1’/’A’ GPRS authentication
0 : PAP(‘NO’ in ‘SyncTrak’)
1 : CHAP(‘YES’ in‘ SyncTrak’)
A: Automatic GPRS set.
In this case, parameters for APN, USER_ID and
USER_PWD field should remain empty.
APN String Access Point Name
USER_ID String ID for GPRS Access
USER_PWD String Password for GPRS Access
SEVER_IP String Server IP Address
SEVER_PORT String Server Port
B_SEVER_IP String IP Address of Backup Server
B_SEVER_PORT String Port of Backup Server
SMS_NO String Phone number that will receive the SMS report sent by the
device. This can be used for backup in the area where
GPRS condition is not good. Or, it can be used as a main
report receiver when IP and Port are unavailable. If it is not
used, it should remain empty.
PIN_NO String PIN Number to release PIN lock if it is enabled
<Example>
[command] ST300NTW;100850000;02;0;internet;;;111.111.111.111;8600;;;;
[response] ST300NTW;Res;100850000;010;0;internet;;; 111.111.111.111;8600;;;;
ST300NTW;Res;100850000;010;A1;tim.br;tim;tim; 111.111.111.111;8600;;;;

<Note>:
** If network does not require User ID and Password, these fields should remain empty.

Automatic Setting for GPRS Network

If you set the device to ‘Automatic GPRS Set’, the device will automatically set the parameters for GPRS with
the data available on the inserted SIM card.
For instance, if Airtel SIM is inserted, the device will set ‘AUTH’ to ‘0’, ‘APN’ to ‘airtelgprs.com’, ‘USER_ID and
USER_PASS’ to empty respectively.
And then, the device reports response string after adding real GPRS parameters, if ‘Automatic GPRS Set’ is
selected.

DNS
Server_IP and B_SERVER_IP field can be filled with direct IP address (for example 111.111.111.111) or
domain name (for example, suntechint.com). If this field is written by domain, the device will find real IP address
by DNS and sends reports to IP address.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 14 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-2. Reporting parameters

Device responds to the command(s) with the relevant report or response periodically at a time interval or at a
travelled distance interval of the vehicle that has already been pre-defined by user. Such are response sent back to
the server includes SMS message (if the device user has already configured SMS messaging functionality). The
following table shows how to set those parameters.

In bottom part of the table, the following table also shows how and what parameters should be set to utilize
functions like:

 ‘Angle Report’, that is used for displaying the historic path more accurately or saving network cost while
the vehicle is driving on straight roads for long time, and

 ‘FIFO’ or ‘LIFO’, that should be selected to determine a sequential order if buffer of the device is
completely full of reports. For more information, have a look at the description made in the bottom part of
the table below.

HDR DEV_ID VER T1 T2 T3 A1 SND_DIST T4 SMS_T1 SMS_T2 SMS_PACK_NO

Field Marks Value Meaning

HDR “ST300RPT” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
T1 String Sec Interval to be set to send a Status Report in parking mode:

Range : 0 ~ 86400
If 0, a report in parking will be sent only one time when
vehicle starts being parked.
T2 String Sec Interval to be set to send a Status Report in driving mode:

Range : 0 ~ 60000
If 0, a report in driving will be sent only one time when
vehicle starts driving.
T3 String Sec Interval to be set to send a Status Report in emergency
mode:

Range : 0 ~ 9999
If 0, an emergency report will be sent only one time when an
emergency state occurs.
A1 String Number of attempts to send an emergency report until the
device gets acknowledgement from the server:

If 0, no Emergency Report will be sent.

If 65500, unlimited report until get ACK from Server.
SND_DIST String Meter Distance interval to be set when the device sends a Status
Report:

Range : 0 ~ 60000 (60km)

If 0, a Status Report on traveled distance is disabled.
If not 0, a Status Report is sent when traveled distance
reaches the predefined SND_DIST.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 15 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

T4 String Sec Interval to be set to send a Keep Alive string.

Range: 0 ~ 65500
SMS_T1 String Min Interval to be set to send a Status Report in parking mode
Range: 0 ~ 99999
SMS_T2 String Min Interval to be set to send a Status Report in driving mode
Range: 0 ~ 99999
SMS_PACK_NO String Report No in one SMS message
Range: 0 ~ 5
<Example>

[command] ST300RPT;100850000;02;180;120;60;3;0;0;0;0;0
[response] ST300RPT;Res;100850000;010;180;120;60;3;0;0;0;0;0

<Note>:

** If a reporting interval is set with a big number, the network may disconnect GPRS connection because GPRS
communication does not make a progress for a long time. So, the device may not receive the command via
GPRS. “T4” will be used to prevent such a disconnection by sending a short data for short time.

** The ‘Keep Alive’ report is sent only when the device has no data to be sent for the time of the interval ‘T4’.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 16 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-3. Event parameters

In order to set these parameters properly, read carefully the contents and <Example> along with <Note> described
in the bottom inside the table below.

HDR DEV_ID VER IGNITION T1 T2

IN1_TYPE IN2_TYPE IN3_TYPE IN1_CHAT IN2_CHAT IN3_CHAT

OUT1_TYPE OUT2_TYPE OUT1_ACTIVE OUT2_ACTIVE

PULSE1_NO PULSE1_ON PULSE1_OFF PULSE2_NO PULSE2_ON PULSE2_OFF

IN4_TYPE IN5_TYPE IN4_CHAT IN5_CHAT BAUD

Field Marks Value Meaning

HDR “ST300EVT” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
IGNITION ‘0’ ~ ‘3’ Ignition using state:

0 : Use Ignition with Input1

1 : Reserved (Line ignition)
2 : Virtual ignition(power)
3 : Virtual ignition (motion)
Default = ‘0’
T1 String Sec Delay in entering parking mode after ignition goes to OFF
T2 String Sec Delay in entering driving mode after ignition goes to ON
IN1_TYPE ‘0’ ~ ‘21’ 0 = Falling Edge
1 = Rising Edge
2 = Both Edge (Falling & Rising)
3 = Panic Button
7 = Anti-Theft Button
11 = Door Sensor
12 = Ignition Line
13 = Disable Immobilizer if it’s activated by jammer Detector
15 = Anti-Theft Button 2
17 = HMeter
19 = Rain Sensor (Gnd)
20 = Rain Sensor (Open)
21 = Rain Sensor (Pulse)
Please refer below note for rain sensors. (19 ~20)

Default = ‘12’.
IN2_TYPE ‘0’ ~ ‘21’ Same as IN1_TYPE except for Ignition Line.
Default = ‘3’
IN3_TYPE ‘9’ 9 = No Use
This device does not have INPUT3
IN1_CHAT String 100ms Input1 chattering time.
Range : 0 ~ 9999
Default = 0 sec.

If 0, input1 is not checked.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 17 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

IN2_CHAT String 100ms Input2 chattering time.

Range : 0 ~ 9999
Default = 3 sec. (30)

If ‘0’, the input2 is not checked.

IN3_CHAT ‘0’ 100ms This device does not have INPUT3
It should be set to ‘0’.
OUT1_TYPE ‘0’ ~ ‘9’ 0 = GPIO
1 = immobilizer
2 = Immobilizer Auto
3 = Pulse
5 = Buzzer
8 = Immobilizer 2
9 = Auto Immobilizer 2
OUT2_TYPE ‘7’ 7 = No Use
This device does not have OUTPUT2
OUT1_ACTIVE ‘0’ or ‘1’ 0 = Open when out1 is active
1 = GND when out1 is active
OUT2_ACTIVE ‘0’ This device does not have OUTPUT2.
It should be set to ‘0’.
PULSE1_NO String Pulse number when the out1 type is set to pulse.
Range : 0 ~ 9999
If Pulse Number is 9999, pulsing runs permanently.
PULSE1_ON String 100ms Active time of Pulse1:

Range : 0 ~ 9999
It should be set with an even number.
PULSE1_OFF String 100ms Inactive time of Pulse1:

Range : 0 ~ 9999
It should be set with an even number.
PULSE2_NO ‘0’ This device does not have OUTPUT2
PULSE2_ON ‘0’ This device does not have OUTPUT2
PULSE2_OFF ‘0’ This device does not have OUTPUT2
IN4_TYPE ‘9’ This device does not have INPUT4
IN5_TYPE ‘9’ This device does not have INPUT5
IN4_CHAT ‘0’ This device does not have INPUT4
IN5_CHAT ‘0’ This device does not have INPUT5
BAUD ‘0’ ~ ‘6’ Baud-rate are:
0 = No use
1 = 4800bps
2 = 9600bps
3 = 19200bps
4 = 38400bps
5 = 115200bps
6 = 2400bps

<Example>
[command] ST300EVT;100850000;02;1;60;0;3;2;9;30;20;0;1;7;1;0;0;0;0;0;0;0;9;9;0;0;0
[response] ST300EVT;Res;100850000;010;1;60;0;3;2;9;30;20;0;1;7;1;0;0;0;0;0;0;0;9;9;0;0;0

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 18 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

<Note>:

** If IGNITION is set to ‘0’, the device doesn’t check driving or parking state of the vehicle. It always reports
status string under parking mode, and cannot support Parking Lock and the Service which enters Sleep or Deep
Sleep automatically when the vehicle is parked.

** If IGNITION is set to ‘2’, the device checks driving or parking state of the vehicle with voltage range of
vehicle’s battery. We named it as ‘Virtual Ignition’. Virtual ignition runs when the device installed on a real
vehicle and it may need to adjust the voltage range for special vehicle.

** “IGNITION” should be selected to “Not Use Ignition” if “IN1_TYPE” = 12.

** In case of pulse, pulse time may have tolerance about dozens of ms.

** Rain Sensor
Rain sensors are inputs to check if it rains.
If the type of rain sensor set to ‘GND’, the device recognizes rain when related line keeps ground during
chattering time. Also, if it set to ‘OPEN’, the device recognizes rain when the line keeps logical high or open
state during chattering time.
If the type of rain sensor set to ‘PULSE’, related chattering time means maximum time of one cycle of pulses.
In this case, the device recognizes rain when pulses that don’t exceed related chattering time continue to be
generated.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 19 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-4. GSM parameters for SMS messaging / phone Calling

In order to set these parameters properly, read carefully the contents and <Example> along with <Note> described
in the bottom inside the table below.

HDR DEV_ID VER SMS_LOCK SMS_MT1 SMS_MT2 SMS_MT3

SMS_MT4 IN_CALL_LOCK CALL_MT1 CALL_MT2 CALL_MT3 CALL_MT4 CALL_MT5

CALL_MO1 CALL_MO2

Field Marks Value Meaning

HDR “ST300GSM” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
SMS_LOCK ‘0’ or ‘1’ Lock of Receiving Commands by SMS
Disable (0) / Enable (1)
If enabled, only the commands which have been
received from SMS_MT1 ~ MT4, their number(s) can be
accepted.
SMS_MT1 String Up to 20 char. Phone number for SMS commands
SMS_MT2 String Up to 20 char. Phone number for SMS commands
SMS_MT3 String Up to 20 char. Phone number for SMS commands
SMS_MT4 String Up to 20 char. Phone number for SMS commands
IN_CALL_LOCK ‘0’’ Not supported
CALL_MT1 Not supported
CALL_MT2 Not supported
CALL_MT3 Not supported
CALL_MT4 Not supported
CALL_MT5 Not supported
CALL_MO1 Not supported
CALL_MO2 Not supported
<Example>
[command] ST300GSM;100850000;02;0;;;;;0;;;;;;;
[response] ST300GSM;Res;100850000;010;0;;;;;0;;;;;;;

<Note>
** When SMS or Call numbers are not set, that field should be empty.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 20 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-5. Parameters for various features

In order to set these various parameters properly, read carefully the contents and <Example> along with <Note>
described in the bottom inside the table below. In setting a new device, the ‘SyncTrak’ will show you detailed
explanation on how to set parameters relating to these ‘Fields’.

HDR DEV_ID VER PARKING_LOCK SPEED_LIMIT PWR_DN CON_TYPE

ZIP GROUP_SEND MP_CHK ANT_CHK BAT_CHK M_SENSOR CALL

GEO_FENCE DATA_LOG

Field Marks Value Meaning

HDR “ST300SVC” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
PARKING_LOCK ‘0’ or ‘1’ Parking lock enable (1) / disable (0):

If 1, the device periodically checks vehicle position under

parking status. When the vehicle goes off some boundary or
starts moving faster than the predefined velocity, the device
reports the Parking Lock Emergency.
SPEED_LIMIT String Km/h Over speed limit:

If 0, the device does not check the over-speed.

If 1 and if the vehicle runs faster than the over predefined

value, the device reports an alert once.
PWR_DN ‘0’ ~ ‘2’ Power saving type:

0 : Disabled sleep and deep sleep service

1 : Enabled deep sleep
2 : Enabled sleep
CON_TYPE ‘0’ or ‘1’ Connection Type with Server:

0 = KEEP_CON
1 = KEEP_DISCON
Detail explanation is below.
ZIP ‘0’ or ‘1’ Use Zip
Disable (0) / Enable (1)
GROUP_SEND ‘0’ or ‘1’ Group Send for stored data:

0 : Disable
1 : Enable. One packet can include up to 5 reports.
The ‘Group Send’ function is explained below.
MP_CHK ‘0’ or ‘1’ Checking Main Power Disconnection:

Disable (0) / Enable (1)

ANT_CHK ‘0’ or ‘1’ GPS Antenna Connection Error Check:

Disable (0) / Enable (1)

BAT_CHK ‘0’ or ‘1’ Backup Battery Error Check:

Disable (0) / Enable (1)

Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 21 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

M_SENSOR ‘0’ ~’7’ Motion Sensor

Motion Collision Shock
0 Disable Disable Disable
1 Enable Disable Disable
2 Disable Disable Enable
3 Enable Disable Enable
4 Disable Enable Disable
5 Enable Enable Disable
6 Disable Enable Enable
7 Enable Enable Enable
CALL ‘0’ Not supported
GEO_FENCE ‘0’ or ‘1’ Support Geo-fence:

Disable (0) / Enable (1)

DATA_LOG ‘0’ or ‘1’ This parameter is not used now.
But you can get all the stored data log from the device by
using the SyncDown program and Setting cable.
<Example>
[command] ST300SVC;100850000;02;1;120;0;0;0;0;1;1;1;0;0;0;0
[response] ST300SVC;Res;100850000;010;1;120;0;0;0;0;1;1;1;0;0;0;0

<Note>:

** Function of M_SENSOR can be used with the model that has motion sensor.
If shock or collision detection is enabled and if there is shock or collision on the vehicle, the device sends a
report to the server.

** If these parameters are customized for your device, please follow the instructions customized for you instead
of using this table.

CON_TYPE

1. KEEP_CON: Device always keeps TCP connection and can receive a command via GPRS.

2. KEEP_DISCON: Device maintains TCP connection while the device is sending the data to the server.
Within 3 minutes after sending all the data that the device has been keeping, the device disconnects
GPRS and TCP connection as there is no data to be sent any more inside the device. In this case, the
device cannot receive a command via GPRS.

Group Send
Device stores data if the vehicle is in ‘no GPRS area’. And, the vehicle moves to GPRS available area, device
starts sending the stored data.
If the ‘Group Send option’ is enabled, the device sends the server5 reports at one time as one bundle.
The ‘Group Send’ is useful to speed up sending.

M_Sensor
1. Collision: Device sends an event report when ignition is ON and the vehicle moves.
2. Shock: Device sends an event report when ignition is OFF and the vehicle moves.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 22 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-6. Vehicle battery parameters

In order to set these parameters properly, read carefully the contents and <Example> along with <Note> described
in the bottom inside the table below. In setting a new device, the ‘SyncTrak’ will show you detailed explanation on
how to set parameters relating to these ‘Fields’.

HDR DEV_ID VER CHR_STOP_THRES_12 CHR_STOP_THRES_24 DECIDE_BAT_24

OPERATION_STOP_THRES_12 OPERATION_STOP_THRES_24 IGNDET_H IGNDET_L

Field Marks Meaning

HDR “ST300MBV” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
CHR_STOP_THRES_12 String Not used
CHR_STOP_THRES_24 String Not used
DECIDE_BAT_24 String Voltage value to check if the vehicle’s battery is 12V or
24V.
OPERATION_STOP_THRES_12 String Voltage value to protect vehicle battery.
In case of 12 V vehicle, the device stops operation if car
battery voltage gets lower than this value.
OPERATION_STOP_THRES_24 String Voltage value to protect vehicle.
In case of 24 V vehicle, the device stops operation if car
battery voltage gets lower than this value.
In case of virtual ignition, the vehicle can recognize driving
state when vehicle power is higher than IGNDET_H.
IGNDET_H String
Default = ‘0’
IGNDET_L String In case of virtual ignition, the vehicle can recognize parking
state when vehicle power is less than IGNDET_L.

Default = ‘0’
<Example>
[command] ST300MBV;100850000;02;0;22;19;8.00;18.00;0;0
[response]ST300MBV;Res;100850000;122;0;22;19;8.00;18.00;0;0

<Note>
1. IGNDET_H and IGNDET_L are ‘0’, device check parking and driving automatically.
2. CHR_STOP_THRES_12 and CHR_STOP_THRES_24 parameters are not used in this device.
Charging is stopped every time when vehicle mode changed to Parking.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 23 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-7. Motion sensor parameters

In order to set these parameters properly, read carefully the contents and <Example> along with <Note> described
in the bottom inside the table below. In setting a new device, the ‘SyncTrak’ will show you detailed explanation on
how to set parameters relating to these ‘Fields’.
HDR DEV_ID VER SHOCK_DELAY MOTION_THRES SHOCK_THRES

COLL_THRES

Field Marks Value Meaning

HDR “ST300MSR” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
SHOCK_DELAY String Sec. Delay in entering shock detection mode after ignition off
0 – Disable
Range : 1 ~ 21600 (5hour)
Recommend: 600 ( 10 min.)
MOTION_THRES String Step Detection level of shock violation.
Range : 0.04 ~ 2.0
Recommend : 0.06
SHOCK_THRES String Step Detection level of shock violation.
Range : 0.04 ~ 2.0
Recommend : 0.10
COLL_THRES String Step Gravity for collision report.
Range : 0.1 ~ 2.0
Recommend : 0.7
<Example>
[command] ST300MSR;100850000;02;600;0.04;0.04;0.7
[response] ST300MSR;Res;100850000;128;600;0.04;0.04;0.70
<Note>
* For the shock level, it is recommended that the user should set to 0.04. If the motion threshold is higher
than0.04, the sensor will be too sensitive to make a proper detection on shock.
The setting values of “ MOTION_THRES < SHOCK_THRES < COLL_THRES ”

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 24 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-8. Circular geo-fencing parameters

This table shows how a device user can set parameters for circular geo-fencing. In order to set these parameters
properly, read carefully the contents and <Example> along with <Note> described in the bottom inside the table
below. In setting a new device, the ‘SyncTrak’ will show you detailed explanation on how to set parameters relating
to these ‘Fields’.

HDR DEV_ID VER GEO_ID ACTIVE LAT LON RADIUS IN OUT

Field Marks Value Meaning

HDR “ST300CGF” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
GEO_ID ‘1’ ~ ‘200’ Geo-fence ID
ACTIVE ‘0’ or ‘1’ enable (1) or disable (0)
LAT String Central latitude of circular area
LON String Central longitude of circular area
RADIUS String meter Radius of circular area
Range : 30~65,000
IN ‘0’ or ‘1’ Alert that a vehicle enters into the circular area.
Enable (1) or disable (0)
OUT ‘0’ or ‘1’ Alert that a vehicle goes out from the circular area.
Enable (1) or disable (0)
GEO_SPD_LIMIT ‘0’ ~ ‘300’ Km/h If zero, checking over-speed in a circle geo-fence is not
supported.
If not zero, when the vehicle is inside in a geo-fence, the
device checks over-speed with GEO_SPD_LIMIT.
GEO_SPD_LIMIT ‘0’~’1800’ Seconds De-bouncing time to confirming over-speed in a circle geo-
_DEBOUNCE fence.
<Example>
[command] ST300CGF;100850000;02;1;1;+37.000000;+127.000000;50;1;1;75.0;30
[response] ST300CGF;Res;100850000;010;1;1;+37.000000;+127.000000;50;1;1;75.0;30

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 25 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-9. Additional parameters (TCP/UDP parameters)

In order to set these parameters properly, read carefully the contents and <Example> along with <Note> described
in the bottom inside the table below. In setting a new device, the ‘Additional Parameter’ section available in the
‘SyncTrak’ program will show you detailed explanation on how to set parameters relating to these ‘Fields’.

HDR DEV_ID VER SVR_TYPE B_SVR_TYPE UDP_ACK DEV_PORT OLD_PROTOCOL

SAT_OUT SAT_DELAY SAT_RS232

Field Definitions Unit Remark

HDR “ST300ADP” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
SVR_TYPE ‘T’ / ‘U’ Server Protocol Type
T : TCP
U : UDP
B_SVR_TYPE ‘T’ / ‘U’ Backup Server Protocol Type
T : TCP
U : UDP
UDP_ACK ‘0’ ~ ‘3’ ‘ACK’ from the server when UDP is used:

0 : No Use

1 : ACK (‘Acknowledgement’ to be made by the server right

after receiving a report from the device) when the server
receives reports except ‘Alive’

2 : ACK when the server receives reports except ‘STT (Status)

Report ‘and ‘Alive Report’

3 : ACK when the server receives an ‘emergency report’.

‘Command response ‘doesn’t need ACK.

DEV_PORT String It is a port of the device for receiving commands from the
server via UDP.

It can be used only when UDP server is used.

If ‘0’ or empty, the device would use port 9000.

If not zero, the device can receive commands through the port,
DEV_PORT.
OLD_PROTOCOL ‘0’~’1’ If ‘0’, follow this document about commands and reports.
If ‘1’, follow old document of ST215 or ST240 series.
( For example, use “SA200” as header and 6digits as unit ID)
SAT_OUT String ‘0’~‘1’ Output1 controls for satellite modem can detect the situation of
no GSM.
0 = Disable
1 = Enable satellite if lost GSM signal with OUT1Please refer
below note, Control of Satellite Modem.
SAT_DELAY String Sec Delay time to activate the output after losing GSM/GPRS
Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 26 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

signal.
Range : 0 ~ 86400
Please refer below note, Control of Satellite Modem
SAT_RS232 String ‘0’ or ‘1’ Send reports through RS232 when SAT_OUT is activated.
0 : Disable
1 : Enable
Caution: This function use only in ST300R.
Please refer below note, Control of Satellite Modem
NO_USE ‘0’ It had been used in old firmware.
RESERVED
<example>
[command] ST300ADP;100850000;02;U;T;2;9000;0;0;0;0;0;0
[response] ST300ADP;Res;100850000;022;U;T;2;9000;0;0;0;0;0;0

<notes>

ACK in case of UDP

UDP is protocol that doesn’t check whether the data is transmitted successfully. So, the device checks
completion of sending with ACK depending on UDP_ACK type.
ACK is sent by server when the server receives the data.
If the ACK has not been sent for more than 2 minutes after sending, the device recognizes the data has not
been reached to the server and sends the data again.

Examples of ACK report are as below.

String Format : “ST300ACK;100850000”
Zip Format : 0x15 0x85 0x00 0x00

Device users are recommended to set ACK_TYPE to ‘1’ to confirm that all the data can be transmitted
successfully.
Report Type UDP_ACK=0 UDP_ACK=1 UDP_ACK=2 UDP_ACK=3
Alive X X X X
STT X O X X
Event, Alert, Etc. X O O X
Emergency X O O O

<Note>
‘O’: Necessary
‘X’: Not necessary

Control of Satellite Modem

SAT_OUT, SAT_DELAY and SAT_RS232 are used for connected satellite modem can communicate with
server instead of the device under no GSM/GPRS situation.

Operation of the control is as follows.

1. If no GSM/GPRS situation keeps more than SAT_DELAY, the device activates related output depend on
SAT_OUT.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 27 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

2. If SAT_OUT is activated, the satellite modem detects no GSM situation and starts own
communication.
3. If SAT_RS232 is enabled, the device sends STT string which has ‘0’ in MSG_TYPE field through RS232.
And then it sends all reports except for STT and Alive.
4. If GSM signal is recovered, the device deactivates output line related on SAT_OUT. If SAT_RS232 is
enabled, STT string which has ‘0’ in MSG_TYPE field is sent before the deactivation.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 28 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-10. Additional parameters2

In order to set these parameters properly, read carefully the contents and <Example> along with <Note> described
in the bottom inside the table below. In setting a new device, the ‘Additional Parameter 2’ section available in the
‘SyncTrak’ program will show you detailed explanation on how to set parameters relating to these ‘Fields’.

DELAY_FOR_ SPEED_LIMIT_ DELAY_FOR_

HDR DEV_ID VER
OVSPD_RPT UNDER_RAIN RAIN_OVSPD_RPT
RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED

RESERVED RESERVED RESERVED RESERVED RESERVED RESERVED

Field Definitions Unit Remark

HDR “ST300AD2” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
DELAY_FOR_ ‘0’ ~ ‘600’ Delay for alert report of over-speed.
_OVSPD_RPT If the device has buzzer, the buzzer activates as soon as the
vehicle runs faster than SPEED_LIMIT.
But, the ‘alert for over-speed’ would be reported after
DELAY_FOR_ OVSPD_RPT seconds.

Unit : seconds
SPEED_LIMIT_UN String Km/h Over speed limit under the rain.
DER_RAIN ‘0’ ~ ‘300’ If 0, the device does not check over speed under rain.
If greater than 0 and when it rains, the device checks over-
speed under rain with SPEED_LIMIT_UNDER_RAIN.
DELAY_FOR_RAIN ‘0’ ~ ‘600’ Delay for alert report of over speed under rain.
_OVSPD_RPT If the device has buzzer, the buzzer activates as soon as the
vehicle runs faster than SPEED_LIMIT_UNDER_RAIN.
But, the ‘alert for over-speed under rain’ would be reported
after DELAY_FOR_RAIN_OVSPD_RPT seconds.

Unit : seconds
RESERVE
RESERVE
RESERVE
RESERVE
RESERVE
RESERVE
RESERVE
RESERVE
RESERVE
RESERVE
RESERVE
RESERVE
<example>
[command] ST300AD2;100850000;02;60;80;60;;;;;;;;;;;;
[response] ST300AD2;Res;100850000;1093;60;80;60;;;;;;;;;;;;

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 29 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-11. New parameters

In order to set these parameters properly, read carefully the contents and <Example> along with <Note> described
in the bottom inside the table below. In setting a new device, the ‘New Parameter Setting’ section available in the
‘SyncTrak’ program will show you detailed explanation on how to set parameters relating to these ‘Fields’.

HDR DEV_ID VER ANGLE_RPT RPT_TYPE ANTITHFT_CNT1 ANTITHFT_CNT2 JAM_DET

JAM_CHK_DIST JAM_CHK_TM VI_ON_THRES VI_ON_DELAY VI_ON_PERCENT

VI_OFF_PERC
VI_OFF_THRES VI_OFF_DELAY HBM_STT
ENT

● Definition : Set parameters related on report interval.

Field Definitions Unit Remark

HDR “ST300NPT” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
ANGLE_RPT String degree Reporting about the STT Message if the steering angle is
greater than ANGLE_RPT:

Disable : 0
Enable : more than 0 and less than 180 degrees
RPT_TYPE String ‘0’ or ‘1’ How to set a sequential rule of storing/erasing reports if
buffer of the device is full of reports un-sent to the server:

0: FIFO: First in First Out.

1: LIFO: Last In First Out.
ANTITHFT_CNT1 String Sec Delay of Anti-Theft Release:

When ignition is on, it starts Anti-Theft emergency state after

the user-defined time.
Range : 10 to 60000 second
ANTITHFT_CNT2 String Sec Delay of Anti-Theft Alert:

When it is Anti-theft emergency state, it sends the

emergency report after the user-defined time.
Range : 0 to 60000 second
JAM_DET String ‘0’ ~’3 GPRS or GPRS+GPS Jamming detection function:

0 = Disable
1 ~ 4 = enabled jamming detection and if detected first,
check assist functions and then triggered by JAM_DET mode
as follows.
JAM_DET Alert Active Immob. Active Buzzer
‘1’ O X X
‘2’ O O X
‘3’ O X O

X – Inactive, O – Activated if jamming is detected.

Immobilizer: You can disable it by command.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 30 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

Buzzer: It is disabled automatically after being released from

jamming.

Device will send an alert after recovering the GSM network.

It takes about 2 minutes or more for the device to complete a
jamming detection.

Default : 0
JAM_CHK_DIST ‘0’ ~’60000’ Meter This is complementary to the detection function of device
described above on the GPRS jamming by utilizing a
distance value as a parameter when jamming is done.

Once jamming on the GPRS network starts being detected,

the device will also check the distance between the current
location of the vehicle and the First geographical Point (‘Fp’)
where the jamming started being detected.

If the distance is greater than JAM_CHK_DIST for a while

triggered by JAM_DET mode.

If ‘0’, skip this procedure.

Default : 500 meters

It is complementary to the function of GPRS jamming
JAM_CHK_TM ‘0’ ~ ‘43200’ Sec. detection in an area ‘without GPS connectivity’ (‘No GPS’).

After detecting jamming first in such a bad GPS connecting

area, the device begins to count the 2 time-length factors (A
and B) to make a sum (A + B = C) if the vehicle moves in the
area:
 A: time length that needs to complete the
jamming detection
 B: time length that the vehicle driver needs to
complete driving in the area.

If C (the sum) is longer than the length of the jamming

detection (‘JAM_CHK_TM’) the device judges that jamming
was done in the area. Please refer to the table for more
details.

If the has not moved in the area, ignore jamming detection

until the jamming detection function is released.

If ‘0’, skip this procedure.

Default: 300 seconds.

VI_ON_THRES String 1/255G Threshold value for Motion Virtual Ignition On
Range : 3~30
Default : 5
VI_ON_DELAY String Sec. Delay time for Motion Virtual Ignition On
Range : 3~999
Default : 10
VI_ON_PERCENT String % Percent for Motion Virtual Ignition On.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 31 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

Range : 30~100
Default: 70
VI_OFF_THRES String 1/255G Threshold value for Motion Virtual Ignition Off
Range : 3~30
Default : 5
VI_OFF_DELAY String Sec. Delay time for Motion Virtual Ignition Off
Range : 3~999
Default : 10
VI_OFF_PERCENT String % Percent for Motion virtual Ignition Off.
Range : 30 ~ 100
Default : 70
HBM_STT String ‘0’ ~ ‘2’ Type of report as follows.
0 : Not Increase H_METER/ BCK_VOLT/ MSG_TYPE in
“STT” String
1: Increase H_METER/ BCK_VOLT/ MSG_TYPE in “STT”
String.
2: Increase H_METER/ BCK_VOLT/ MSG_TYPE in “STT”
String and LBS information
<example>
[command] ST300NPT;100850000;02;0;0;0;0;0;500;300;5;10;70;5;10;70;0

[response] ST300NPT;Res;100850000;010; 02;0;0;0;0;0;500;300;5;10;70;5;10;70;0

Jamming detection procedure

JAM_CHK_DIST and & JAM_CHK_TM are complementary to jamming detection to avoid false detection.
At least, we recommend that users of our device should utilize the ‘JAM_CHK_DIST’ for safety purposes.
If you use the 2 (two) functions, it can detect the following two cases of jamming:

*Case A: Jamming GPRS only.

Jamming detected ->JAM_CHK_DIST -> JAM_CHK_TM -> Triggered by JAM_DET mode.

*Case B: Jamming GPRS & GPS.

Jamming detected ->JAM_CHK_TM -> Triggered by JAM_DET mode.

JAM_CHK_DIST: if 0, skip this function.

JAM_CHK_TM: if 0, skip this function.

In case all of the complementary functions are disabled, device starts working according to the jamming mode
(JAM_DET mode) after detecting the jamming. In this case, a false detection might be made in an area having a
weak GSM connectivity or in an area having a strong radio.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 32 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-12. Backup battery parameters

HDR DEV_ID VER SDN_USE SDN_THRES

● Definition : When vehicle battery is disconnected and Backup battery voltage is low, device is turned off.

Field Definitions Unit Remark

HDR “ST300BAT” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
SDN_USE String ‘0’ or ‘1’ 0 : Doesn’t power off the device.
1 : Power off the device when vehicle battery is disconnected
and Backup battery voltage is low
SDN_THRES String Volts Threshold of backup battery voltage for power off.
Minimum: 3.4 Volts
Maximum: 3.8 Volts
<example>
[command] ST300BAT;600850000;02;1;3.5
[response] ST300BAT;Res;600850000;010;1;3.5

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 33 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-13. Telemetry parameters

HDR DEV_ID VER TRAVEL_EVT ODO_USE ODO_UNIT RPM_UNIT ECO_MAX_RPM

ECO_MIN_RPM MAX_RPM DID_OUT_CTRL MASTER_ADD MASTER_REMOVE

CHK_GEAR CHK_GEAR_TIME CHK_GEAR_RPM MAX_REST_TIME MAX_STOP_TIME

● Definition : Set telemetry parameters.

Field Definitions Unit Remark

HDR “ST300HTP” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
TRAVEL_EVT String ‘0’ or ‘1’ 0: Doesn’t send travel event string
1: Send travel event string when the vehicle is parked.
RESERVED String ‘0’ Not Supported (ODO_USE)
RESERVED String ‘A’ Not Supported (ODO_UNIT)
RESERVED String pulse Not Supported (RPM_UNIT)
RESERVED String RPM Not Supported (ECO_MAX_RPM)
RESERVED String RPM Not Supported (ECO_MIN_RPM)
RESERVED String RPM Not Supported (MAX_RPM)
DID_OUT_CTRL String ‘0’ ~ ‘1’ Output control by Driver ID

0 : Disabled
1 : OUT1 is activated automatically when the vehicle starts
driving (ignition on) without registered driver ID

MASTER_ADD String Master driver ID to register new driver ID.

Master is inserted and removed, and then another I-button is
inserted within 10s after removing master. In this case,
another ID can be registered automatically.
MASTER_REMOVE String Master driver ID to unregister driver ID.
Master is inserted and removed, and then another I-button is
inserted within 10s after removing master. In this case,
another ID can be unregistered automatically.
RESERVED String ‘0’ or ‘1’ Not Supported (CHK_GEAR)
RESERVED String Sec. Not Supported (CHK_GEAR_TIME)
RESERVED String RPM Not Supported (CHK_GEAR_RPM)
MAX_REST_TIME String Sec. Time to alert for no driving with ignition on.
If not ‘0’, the device alerts when the driver stops with ignition
on during more MAX_REST_TIME.
MAX_STOP_TIME String Sec. Time to alert for stopping
If not ‘0’, the device alerts when the time of stop exceeds
MAX_STOP_TIME.
<example>
[command] ST300HTP;100850000;02;1;1;16344;16;3200;1500;4000;0;0100004E160000;;1;10;1000;0;0
[response] ST300HTP;Res;100850000;267;1;1;16344;16;3200;1500;4000;0;0100004E160000;;1;10;1000;0;0

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 34 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-14. Setting for Driver ID parameters

4-14-1. ADD Driver ID

st st
HDR DEV_ID VER DID_POS (1 ) DID (1 ) … … DID_POS (last) DID (last)

● Definition : Add driver ID to registration table.

Field Definitions Unit Remark

HDR “ST300HAD” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
st
DID_POS (1 ) “1”~”5000” Index position of driver ID to save
st
DID(1 ) String 14hex digits Driver ID
…
…
DID_POS (last) “1”~”5000” Index position of driver ID to save
DID(last) String 14hex digits Driver ID
<example>
[command] ST300HAD;100850000;02;001;00001000000000;002;00002000ABCDEF;005;00003333AAAAAA;
…
[response] ST300HAD;Res;100850000;267;001; 00001000000000;002; 00002000ABCDEF;005;00003333
AAAAAA; …

After receiving this command, the device will save new driver ID as below table.
st nd
1 position 00001000000000 2 position 00002000ABCDEF
rd th
3 position 4 position
th
5 position 00003333AAAAAA …

<notes>
The driver ID can be register up to 50 IDs at a time.
And, this command overwrites with new ID although the set position has another ID already.

4-14-2. Remove Driver ID

HDR DEV_ID VER DID_POS

● Definition : Remove driver ID to registration table.

Field Definitions Unit Remark

HDR “ST300HRD” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
DID_POS “1”~”5000” Index position of driver ID to remove.
or If “ALL”, all driver ID will be removed.
“ALL”
<example>
[command] ST300HRD;100850000;02;001
[response] ST300HRD;Res;100850000;267;001

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 35 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-14-3. Get Drive ID

HDR DEV_ID VER HD_DID DRIVE_ID_N ID_DRIVER

● Definition : Read driver ID from registration table.

Field Definitions Unit Remark

HDR “ST300HGD” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
DID_POS “1”~”5000” Driver ID’s position
or If “ALL”, the device should informs all driver IDs.
“ALL”
<example>
[command] ST300HGD;100850000;02;001
[response] ST300HGD;Res;100850000;267;001;00001000000000

In case of the device has 51 driver id :

[command] ST300HGD;100850000;02;ALL
[response]
ST300HGD;Res;100850000;267;001;01000000000101;002;01000000000102;003;01000000000103;
004;01000000000104;005;01000000000105;006;01000000000106;007;01000000000107;
008;01000000000108;009;01000000000101;010;01000000000101;011;01000000000111;
012;01000000000112;013;01000000000113;014;01000000000114;015;01000000000115;
016;01000000000116;017;01000000000117;018;01000000000118;019;01000000000119;
…
050;01000000000150;Continued
ST300HGD;Res;100850000;267;051;01000000000151

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 36 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

4-15. Driver Pattern Analysis parameters

HDR DEV_ID VER DRVPTN_EN BASESPEED FASTACCEL

HARSHBRAKE SHARPTURN ENB_BUZZER TIME_BUZZER

● Definition : Set parameter related Driver Pattern Analysis Function.

Field Definitions Unit Remark

HDR “ST300DPA” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
DRVPTN_EN 0 or 1 0 : disable
1 : enable
BASESPEED String Km/h Base speed limitation value (default :
Device will be checking Driver Pattern Data when the current
speed is over this value.
FASTACCEL String [X/256]G Fast acceleration violation value
This value is based on the difference value of speed during 1
second. This value can be set 1 ~ 512
HARSHBRAKE String [X/256]G Harsh brake violation value. This value can be set 1 ~ 512
SHARPTURN String [X/256]G Sharp turn violation value. This value can be set 1 ~ 512
ENB_BUZZER String ‘0’ or ‘1’ 0 : Disable “active output (Buzzer)” when sending Driver
Pattern alert
1 : Enable “active output (Buzzer)” when sending Driver
Pattern alert
TIME_BUZZER String Time to active Buzzer when driver pattern alert.
<example>
[command] ST300DPA;600850000;02;1;50.0;7.5;15.0;45.0;1;5

[response] ST300DPA;Res;600850000;651;1;50.0;7.5;15.0;45.0;1;5

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 37 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

5. Reporting to Server

Once a device is configured properly and registered on its server for operation, it sends reports to the server (or
sends SMS messages to cellular phone whose number is pre-defined) either in response to the commands made
by the server or as per the way how the device has been configured to respond to its server.

This chapter shows the strings of each report, so that server could understand the contents. One report can be
issued in either of two types, normal string and zip string, both of which are described below.

Also, note that we take an <Example> and make a <Note> in bottom part of each report in this chapter to help the
users understand better what contents are included in the report. So, it is highly recommended that users should
read the whole parts of the reports very carefully.

Model Identification Table

Model ID
ST300R 01
ST340 02
ST340LC(4pin) 03
ST300HD 04
ST350 05
ST480 06
ST340 17
ST390 18
ST310U 40
ST360 42
ST340U 44
ST340UR 45

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 38 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

5-1. Status Report

This report (‘Status Report’) is sent to the server periodically as defined by user to configure ‘status report’ if
conditions for issuing the report are met. The following two (2) tables show that one reporting can be made in 2
different types such as in ‘string’ and in ‘zip’.

HDR DEV_ID MODEL SW_VER DATE TIME CELL LAT

LON SPD CRS SATT FIX DIST PWR_VOLT I/O

MODE MSG_NUM H_METER BCK_VOLT MSG_TYPE DID CELL_ID MCC

MNC RX_LVL LAC TM_ADV

5-1-1. Normal

Field Marks Meaning

HDR “ST300STT” Header of Status Report
DEV_ID 9 char. Device ID
MODEL 2Char Device Model (According to table model)
SW_VER String Main version : number
Derived version : alphabet from ‘A’ to ‘O’
Ex) “313”, “313F”
DATE 8 char. GPS date (yyyymmdd)
Year + Month + Day
TIME 8 char. GPS time (hh:mm:ss)
Hour : Minute : Second
CELL String Location Code ID(3 digits hex) + Serving Cell BSIC(2 digits decimal)
LAT String Latitude (+/-xx.xxxxxx)
LON String Longitude (+/-xxx.xxxxxx)
SPD String Speed in km/h
This value returns to 0 when it is over than 200,000km (kilo meters).
CRS String Course on the ground in degree
SATT String Number of satellites
FIX ‘1’ or ‘0’ GPS is fixed (1); GPS is not fixed (0)
DIST String Traveled distance in meter. Max 999999999
PWR_VOLT String Voltage value of the main power
I/O 6 char. Current I/O status of the inputs and the outputs:
Ignition + Input1 + Input 2 + ‘0’ + Out1 + ‘0’
Ignition : ‘1’ (ON), ‘0’ (OFF)
Input1 ~ Input2 : ‘1’ (Ground, Shorted), ‘0’ (Opened)
Out1 : ‘1’ (Active), ‘0’ (Inactive)
MODE 1 char. ‘1’ = Idle mode(Parking)
‘2’ = Active Mode(Driving)
‘4’ = Distance mode
‘5’ = Angle mode
MSG_NUM 4 char. Message number

After “9999” is reported, message number returns to ‘0000”.

H_METER String Driving hour-meter. Max 999999
BCK_VOLT String Voltage value of backup battery
MSG_TYPE 1 char Report is real time (1), Report is storage (0)
DID 14 char. Driver ID (inserted I-button ID ). Only for ST340UR

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 39 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

DID_REG 1 char. State of DID’s registration. Only for ST340UR

‘0’ = not registered. ‘1’ = registered.
CELL_ID String Information of Cell ID
MCC String Information of Mobile Country Code
MNC String Information of Mobile Network Code
RX_LVL String Information of Rx Level
LAC String Information of Location Area Code
TM_ADV String Information of Timing Advance
<Example>
ST300STT;100850000;07;301;20170103;01:45:10;01454;+37.479265;+126.887877;000.000;104.38;13;1;0;12.
14;000000;1;0001;000000;3.8;1;012497F1160000;1;73;01c2;00;-82;20;1

ST300STT;100850000;07;301F;20170103;01:45:10;01454;+37.479265;+126.887877;000.000;104.38;13;1;0;12
.14;000000;1;0001;000000;3.8;1;012497F1160000;1;73;01c2;00;-82;20;1

<Note>
The report can be constructed depending on HBM_STT option in new parameters.
If HBM_STT is set to ‘0’, the report ends at MSG_NUM.
If HBM_STT is set to ‘1’, the reports include up to DID_REG.
If HBM_STT is set to ‘2;, the reports include whole field.

5-1-2. Zip

Field Marks Meaning

STX 0x02 Start of zip data
PKT_LEN 2 Bytes Length of zip data, HDR to MSG_TYPE
HDR 0x10 Header of Status Report
DEV_ID 5 bytes Device ID
BCD format

If the Device ID is 123456789, this field will be filled with 0x12, 0x34,
0x56 0x78 and 0x90.
MODEL 1byte Device Model (According to table model)
SW_VER 2 bytes
Bit 15 ~ Bit 12 Bit 11 ~ Bit 0
Version letter Version Number

Version letter represents alphabet following version number.

The range of this from ‘A’ to ‘O’.
The other bits field means version number.
The range of this is from 0 to 4095.
th th
If the version has no alphabet, bits from 12 to 15 should be zero.
Ex) 6139
6 means ‘F’, and 139 means V313.
DATE_TIME 6 bytes GPS date & Time (Year + Month + Day + Hour + Minute + Second)
CELL 3 bytes Location Code ID (2 bytes) + Serving Cell BSIC (1 byte)
LAT 4 bytes 1 byte (integer) + 3 bytes (BCD)
LON 4 bytes 1 byte (integer) + 3bytes (BCD)
SPD 3 bytes 2 bytes (integer) + 1 byte (BCD)
CRS 3 bytes 2 bytes (integer) + 1 byte (BCD)
SATT_FIX 1 byte
Bit 7 Bit 6 Bit 5 Bit 4 ~ Bit 0
Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 40 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

Fix Latitude Longitude Satellite’s count

+/- sign +/- sign
+ sign = 0, - sign = 1

DIST 4 bytes Traveled distance in meter

PWR_VOLT 2 bytes Voltage value of main power
1 byte (integer) + 1 byte (BCD)
I/O 1 byte
Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
‘0’ Out1 ‘0’ Input 2 Input1 Ignition
Ignition : ‘1’ (ON), ‘0’ (OFF)
Input1 ~ Input2 : ‘1’ (Ground, Shorted), ‘0’ (Opened)
Out1 : ‘1’ (Active), ‘0’ (Inactive)
MODE 1 byte 1 = Idle (Parking), 2 = Active (Driving), 4 = Distance, 5 = Angle
MSG_NUM 2 bytes Message number

After 9999, message number returns to 0.

H_METER 4 bytes Driving hour-meter
BCK_VOLT 2 bytes Voltage value of backup battery
1 byte (integer) + 1 byte (BCD)
MSG_TYPE 1 byte Report is real time (1), Report is storage (0)
DID 7 bytes Driver ID (inserted I-button ID )
DID_REG 1 byte State of DID’s registration.
0 = not registered. 1 = registered.
CELL_ID 2 bytes Information of Cell ID
MCC 2 bytes Information of Mobile Country Code
MNC 1 byte Information of Mobile Network Code
RX_LVL 2 bytes Information of Rx Level
LAC 2 bytes Information of Location Area Code
TM_ADV 1 bytes Information of Timing Advance
ETX 0x03 End of zip data.
<Example>

Original String :
ST300STT;100850000;07;313F;20170103;01:45:10;01454;+37.479320;+126.887833;000.007;000.00;9;1;0;12.
36;000000;1;0001;000000;3.8;1;012497F1160000;1;73;01c2;00;-82;20;1

Zip Packet
0x02
0x00 0x3c
0x10
0x10 0x08 0x50 0x00 0x00
0x07
0x61 0x39
0x11 0x01 0x03 0x01 0x2d 0x0a
0x00 0x14 0x36
0x25 0x47 0x93 0x20
0x7e 0x88 0x78 0x33
0x00 0x00 0x07
0x00 0x00 0x00
0x89
0x00 0x00 0x00 0x00
0x0c 0x36
0x00 0x00
Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 41 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

0x01
0x00 0x01
0x00 0x00 0x00 0x00
0x03 0x08
0x01
0x01 0x24 0x97 0xF1 0x16 0x00 0x01
0x00 0x49
0x01 0xc2
0x00
0xff 0xae
0x00 0x14
0x01
0x03

<note>
If you want ‘RX_LVL’ data back to normal format to use excel. Use this function.

=IF(HEX2DEC(C1)>HEX2DEC("8FFF"), (HEX2DEC("FFFF")-HEX2DEC(C1)+1)*-1, HEX2DEC(C1))

C1 is position of cell, and this cell has 16 bits hexadecimal data.

‘Timing Advance’ value is last available data. If the device never getting available ‘Timing Advance’ value, it will
be ‘0’.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 42 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

5-2. Emergency Report

When an emergency occurs, device sends to the server this ‘emergency report’ as defined already in the
course of configuring device.

HDR DEV_ID MODEL SW_VER DATE TIME CELL LAT

LON SPD CRS SATT FIX DIST PWR_VOLT I/O

EMG_ID H_METER BCK_VOLT MSG_TYPE CELL_ID MCC MNC RX_LVL

LAC TM_ADV

5-2-1. Normal

Field Marks Meaning

HDR “ST300EMG” Header of Emergency Report
DEV_ID 9 char. Device ID
MODEL 2Char Device Model (According to table model)
SW_VER String Main version : number
Derived version : alphabet from ‘A’ to ‘O’
Ex) “313”, “313F”
DATE 8 char. GPS date (yyyymmdd)
TIME 8 char. GPS time (hh:mm:ss)
CELL String Location Code ID(3 digits hex) + Serving Cell BSIC(2 digits decimal)
LAT String Latitude (+/-xx.xxxxxx)
LON String Longitude (+/-xxx.xxxxxx)
SPD String Speed in km/h
CRS String Course over ground in degree
SATT String Number of satellites
FIX ‘1’ or ‘0’ GPS is fixed (1), GPS is not fixed (0)
DIST String Traveled distance in m.
PWR_VOLT String Voltage value of main power
I/O 6 char. Current I/O status of inputs and outputs.
Ignition + Input1 + Input 2 + ‘0’ + Out1 + ‘0’
Ignition : ‘1’ (ON), ‘0’ (OFF)
Input1 ~ Input2 : ‘1’ (Ground, Shorted), ‘0’ (Opened)
Out1 : ‘1’ (Active), ‘0’ (Inactive)
EMG_ID 1 char. Emergency type:

‘1’ = emergency by panic button

‘2’ = emergency by parking lock
‘3’ = emergency by removing main power.
It’s only available in model that has a backup battery.
‘5’ = emergency by anti-theft
‘6’ = emergency by anti-theft door
‘7’ = emergency by motion
‘8’ = emergency by anti-theft shock
H_METER String Driving hour-meter
BCK_VOLT String Voltage value of backup battery
MSG_TYPE 1 char Report is real time (1), Report is storage (0)
DID 14 char. Driver ID (inserted I-button ID ). Only for ST340UR
DID_REG 1 char. State of DID’s registration. Only for ST340UR
Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 43 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

‘0’ = not registered. ‘1’ = registered.

CELL_ID String Information of Cell ID
MCC String Information of Mobile Country Code
MNC String Information of Mobile Network Code
RX_LVL String Information of Rx Level
LAC String Information of Location Area Code
TM_ADV String Information of Timing Advance

<Example>
ST300EMG;100850000;01;010;20081017;07:41:56;00100;+37.478519;+126.886819;000.012;000.00;9;1;0;12.1
4;001100;1;0;3.8;1;012497F1160000;1;73;01c2;00;-82;20;1

<Note>
Emergency reports are sent A1 times until the unit receives server acknowledge.
The “H_METER/ BCK_VOLT/ MSG_TYPE” are included in STT only when “HBM_STT” is “1”
CELL_ID to TM_ADV are included in STT only when “HBM_STT” is “2”

5-2-2. Zip

Field Marks Meaning

STX 0x02 Start of zip data
PKT_LEN 2 Bytes Length of zip data, HDR to MSG_TYPE
HDR 0x11 Header of Emergency Report
DEV_ID 5 bytes Device ID
BCD format

If the Device ID is 123456789, this field will be filled with 0x12, 0x34,
0x56 0x78 and 0x90.
MODEL 1byte Device Model (According to table model)
SW_VER 2 bytes
Bit 15 ~ Bit 12 Bit 11 ~ Bit 0
Version letter Version Number

Version letter represents alphabet following version number.

The range of this from ‘A’ to ‘O’.
The other bits field means version number.
The range of this is from 0 to 4095.
th th
If the version has no alphabet, bits from 12 to 15 should be zero.
Ex) 6139
6 means ‘F’, and 139 means V313.
DATE_TIME 6 bytes GPS date & Time (Year + Month + Day + Hour + Minute + Second)
CELL 3 bytes Location Code ID (2 Bytes) + Serving Cell BSIC (1 Byte)
LAT 4 bytes 1 byte (integer) + 3 bytes (BCD)
LON 4 bytes 1 byte (integer) + 3bytes (BCD)
SPD 3 bytes 2 bytes (integer) + 1 byte (BCD)
CRS 3 bytes 2 bytes (integer) + 1 byte (BCD)
SATT_FIX 1 byte
Bit 7 Bit 6 Bit 5 Bit 4 ~ Bit 0
Fix Latitude Longitude Satellite’s count
+/- sign +/- sign
+ sign = 0, - sign = 1

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 44 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

DIST 4 byte Traveled distance in meter

PWR_VOLT 2bytes Voltage value of the main power
1 byte (integer) + 1 byte (BCD)
I/O 1 byte
Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
‘0’ Out1 ‘0’ Input 2 Input1 Ignition
Ignition : ‘1’ (ON), ‘0’ (OFF)
Input1 ~ Input2 : ‘1’ (Ground, Shorted), ‘0’ (Opened)
Out1 : ‘1’ (Active), ‘0’ (Inactive)
EMG_ID 1 byte Emergency type:

1 = emergency by panic button

2 = emergency by parking lock
3 = emergency by removing the main power
It’s only available in model that has a backup battery.
5 = emergency by anti-theft
6 = emergency by anti-theft door
7 = emergency by motion
8 = emergency by anti-theft shock
H_METER 4bytes Driving hour-meter
BCK_VOLT 2bytes Voltage value of backup battery
MSG_TYPE 1 char Report is real time (1), Report is storage (0)
DID 7 bytes Driver ID (inserted I-button ID )
DID_REG 1 byte State of DID’s registration.
0 = not registered. 1 = registered.
CELL_ID 2 bytes Information of Cell ID
MCC 2 bytes Information of Mobile Country Code
MNC 1 byte Information of Mobile Network Code
RX_LVL 2 bytes Information of Rx Level
LAC 2 bytes Information of Location Area Code
TM_ADV 1 bytes Information of Timing Advance
ETX 0x03 End of zip data.

<Example>
Original String :
ST300EMG;100850001;01;313F;20181017;07:41:56;2F100;+37.478519;+126.886819;000.007;000.00;9;1;
0;12.14;000000;1;3.8;1;012497F1160000;1;73;01c2;00;-82;20;1

Zip Packet

0x02
0x00 0x3c
0x11
0x10 0x08 0x50 0x00 0x10
0x01
0x61 0x39
0x12 0x0a 0x11 0x07 0x29 0x38
0x02 0xf1 0x00
0x25 0x47 0x85 0x19
0x7e 0x88 0x68 0x19
0x00 0x00 0x07
0x00 0x00 0x00
0x89
0x00 0x00 0x00 0x00

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 45 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

0x0c 0x14
0x00 0x00
0x01
0x03 0x08
0x01
0x01 0x24 0x97 0xF1 0x16 0x00 0x01
0x00 0x49
0x01 0xc2
0x00
0xff 0xae
0x00 0x14
0x01
0x03

<Note>
Emergency reports are sent A1 times until the unit receives server acknowledge.
The “H_METER/ BCK_VOLT/ MSG_TYPE” is include in emergency report only when “HBM_STT” is “1”
CELL_ID to TM_ADV are included in STT only when “HBM_STT” is “2”

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 46 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

5-3. Event Report

When an emergency occurs, device sends to the server this ‘event report’ as defined already in the
course of configuring the device. The following shows a sample of event report that is sent to the server
if ‘Input Line’ is changed.

HDR DEV_ID MODEL SW_VER DATE TIME CELL LAT

LON SPD CRS SATT FIX DIST PWR_VOLT I/O

EVT_ID H_METER BCK_VOLT MSG_TYPE CELL_ID MCC MNC RX_LVL

LAC TM_ADV

5-3-1. Normal

Field Marks Meaning

HDR “ST300EVT” Header of Event Report
DEV_ID 9 char. Device ID
MODEL 2Char Device Model (According to table model)
SW_VER String Main version : number
Derived version : alphabet from ‘A’ to ‘O’
Ex) “313”, “313F”
DATE 8 char. GPS date (yyyymmdd)
TIME 8 char. GPS time (hh:mm:ss)
CELL String Location Code ID(3 digits hex) + Serving Cell BSIC(2 digits decimal)
LAT String Latitude (+/-xx.xxxxxx)
LON String Longitude (+/-xxx.xxxxxx)
SPD String Speed in km/h
CRS String Course over ground in degree
SATT String Number of satellites
FIX ‘1’ or ‘0’ GPS is fixed (1), GPS is not fixed (0)
DIST String Traveled distance in meter
PWR_VOLT String Voltage value of the main power
I/O 6 char. Current I/O status of inputs and outputs.
Ignition + Input1 + Input 2 + ‘0’ + Out1 + ‘0’
Ignition : ‘1’ (ON), ‘0’ (OFF)
Input1 ~ Input2 : ‘1’ (Ground, Shorted), ‘0’ (Opened)
Out1 : ‘1’ (Active), ‘0’ (Inactive)
EVT_ID 1 char. Event type:
1 = Input1 goes to ground state.
2 = Input1 goes to open state.
3 = Input2 goes to ground state.
4 = Input2 goes to open state.
H_METER String Driving hour-meter
BCK_VOLT String Voltage value of backup battery
MSG_TYPE 1 char Report is real time (1), Report is storage (0)
DID 14 char. Driver ID (inserted I-button ID ). Only for ST340UR
DID_REG 1 char. State of DID’s registration. Only for ST340UR
‘0’ = not registered. ‘1’ = registered.
CELL_ID String Information of Cell ID
MCC String Information of Mobile Country Code
MNC String Information of Mobile Network Code
Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 47 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

RX_LVL String Information of Rx Level

LAC String Information of Location Area Code
TM_ADV String Information of Timing Advance
<Example>
ST300EVT;100850001;01;010;20081017;07:41:56;00100;+37.478519;+126.886819;000.012;000.00;9;1;0;12.1
4;000000;3;1;0;3.8;1;012497F1160000;1;73;01c2;00;-82;20;1

<Note>
The “H_METER/ BCK_VOLT/ MSG_TYPE” is include in event report only when “HBM_STT” is “1”
CELL_ID to TM_ADV are included in STT only when “HBM_STT” is “2”

5-3-2. Zip

Field Marks Meaning

STX 0x02 Start of zip data
PKT_LEN 2 Bytes Length of zip data, HDR to MSG_TYPE
HDR 0x12 Header of Event Report
DEV_ID 5 bytes Device ID
BCD format

If the Device ID is 123456789, this field will be filled with 0x12, 0x34,
0x56 0x78 and 0x90.
MODEL 1byte Device Model (According to table model)
SW_VER 2 bytes
Bit 15 ~ Bit 12 Bit 11 ~ Bit 0
Version letter Version Number

Version letter represents alphabet following version number.

The range of this from ‘A’ to ‘O’.
The other bits field means version number.
The range of this is from 0 to 4095.
th th
If the version has no alphabet, bits from 12 to 15 should be zero.
Ex) 6139
6 means ‘F’, and 139 means V313.
DATE_TIME 6 bytes GPS date & Time (Year + Month + Day + Hour + Minute + Second)
CELL 3 bytes Location Code ID (2 Bytes) + Serving Cell BSIC (1 Byte)
LAT 4 bytes 1 byte (integer) + 3 bytes (BCD)
LON 4 bytes 1 byte (integer) + 3bytes (BCD)
SPD 3 bytes 2 bytes (integer) + 1 byte (BCD)
CRS 3 bytes 2 bytes (integer) + 1 byte (BCD)
SATT_FIX 1 byte
Bit 7 Bit 6 Bit 5 Bit 4 ~ Bit 0
Fix Latitude Longitude Satellite’s count
+/- sign +/- sign
+ sign = 0, - sign = 1

DIST 4 byte Traveled distance in meter

PWR_VOLT 2bytes Voltage value of the main power
1 byte (integer) + 1 byte (BCD)
I/O 1 byte

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 48 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0

‘0’ Out1 ‘0’ Input 2 Input1 Ignition
Ignition : ‘1’ (ON), ‘0’ (OFF)
Input1 ~ Input2 : ‘1’ (Ground, Shorted), ‘0’ (Opened)
Out1 : ‘1’ (Active), ‘0’ (Inactive)Out2 : 1 (Active), 0 (Inactive)
EVT_ID 1 char. Event type:
1 = Input1 goes to ground state.
2 = Input1 goes to open state.
3 = Input2 goes to ground state.
4 = Input2 goes to open state.
H_METER 4bytes Driving hour-meter
BCK_VOLT 2bytes Voltage value of backup battery
MSG_TYPE 1 char Report is real time (1), Report is storage (0)
DID 7 bytes Driver ID (inserted I-button ID )
DID_REG 1 byte State of DID’s registration.
0 = not registered. 1 = registered.
CELL_ID 2 bytes Information of Cell ID
MCC 2 bytes Information of Mobile Country Code
MNC 1 byte Information of Mobile Network Code
RX_LVL 2 bytes Information of Rx Level
LAC 2 bytes Information of Location Area Code
TM_ADV 1 bytes Information of Timing Advance
ETX 0x03 End of zip data.
<Example>

Original String :
ST300EVT;100850000;01;313F;20181017;07:41:56;2F100;+37.478519;+126.886819;000.007;000.00;9;1;0;12.
14;000000;1;0;3.8;1;012497F1160000;1;73;01c2;00;-82;20;1

Zip Packet

0x02
0x00 0x3c
0x12
0x10 0x08 0x50 0x00 0x00
0x01
0x61 0x39
0x14 0x0a 0x11 0x07 0x29 0x38
0x02 0xF1 0x00
0x25 0x47 0x85 0x19
0x7e 0x88 0x68 0x19
0x00 0x00 0x07
0x00 0x00 0x00
0x89
0x00 0x00 0x00 0x00
0x0c 0x14
0x00 0x00
0x01
0x00
0x03 0x08
0x01
0x01 0x24 0x97 0xF1 0x16 0x00 0x01
0x00 0x49
0x01 0xc2

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 49 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

0x00
0xff 0xae
0x00 0x14
0x01
0x03

<Note>
The “H_METER/ BCK_VOLT/ MSG_TYPE” is include in event report only when “HBM_STT ”is “1”
CELL_ID to TM_ADV are included in STT only when “HBM_STT” is “2”

5-4. Alert Report

Device sends ‘Alert’ to the server as defined by user in the course of setting the relevant parameters. Most of cases
that requiring an alert to be issued means that the vehicle or asset or its driver is in danger or is almost in danger
that should be notified by device to the server and/or the cellular phone (If communication via SMS has been
configured) for warning.

Have a close look at the fields from the following table for more information on when and what alerts are triggered.
An <Example> of alerting and <Note> are also described in the bottom part of the table below.

HDR DEV_ID MODEL SW_VER DATE TIME CELL LAT

LON SPD CRS SATT FIX DIST PWR_VOLT I/O

ALERT_ID H_METER BCK_VOLT MSG_TYPE CELL_ID MCC MNC RX_LVL

LAC TM_ADV

5-4-1. Normal

Field Marks Meaning

HDR “ST300ALT” Header of Alert Report
DEV_ID 9 char. Device ID
MODEL 2Char Device Model (According to table model)
SW_VER String Main version : number
Derived version : alphabet from ‘A’ to ‘O’
Ex) “313”, “313F”
DATE 8 char. GPS date (yyyymmdd)
TIME 8 char. GPS time (hh:mm:ss)
CELL String Location Code ID(3 digits hex) + Serving Cell BSIC(2 digits decimal)
LAT String Latitude (+/-xx.xxxxxx)
LON String Longitude (+/-xxx.xxxxxx)
SPD String Speed in km/h
CRS String Course over ground in degree
SATT String Number of satellites
FIX ‘1’ or ‘0’ GPS is fixed (1); GPS is not fixed (0)
DIST String Traveled distance in m.
PWR_VOLT String Voltage value of main power
I/O 6 char. Current I/O status of inputs and outputs.
Ignition + Input1 + Input 2 + ‘0’ + Out1 + ‘0’
Ignition : ‘1’ (ON), ‘0’ (OFF)
Input1 ~ Input2 : ‘1’ (Ground, Shorted), ‘0’ (Opened)
Out1 : ‘1’ (Active), ‘0’ (Inactive)
Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 50 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

ALERT_ID 1 char. Alert type

1 = Start driving faster than SPEED_LIMIT.
2 = Ended over-speed condition
5 = The vehicle exited the geo-fenced area that has the following ID.
(5001 ~ 5200)
6 = The vehicle entered the geo- fenced area that has the following ID.
(5001 ~ 5200)
9 = Enter the Deep Sleep Mode
10 = Exit from the Deep Sleep Mode
13 = Backup battery error
14 = Vehicle battery goes down to a very low level.
Refer to “Protection of Vehicle Battery” chapter.
15 = shocked
16 = Collision has occurred to the vehicle.
40=Connected with the Main Power source
41=Disconnected with the Main Power source
44=Connected with the Back-up Battery
45=Disconnected with the Back-up Battery
46 = Alert of fast acceleration from Driver Pattern Analysis
47 = Alert of harsh brake from Driver Pattern Analysis
48 = Alert of sharp turn from Driver Pattern Analysis
50 = Jamming detected
59 = Inserted I-Button
60 = Removed I-Button
61 = The vehicle turns on (ignition ON) but doesn’t drive during
MAX_REST_TIME.
62 = Stopped more than predefined time.
68 = Completed automatic Driver Pattern calibration.
70 = Alert when the vehicle runs faster than
‘SPEED_LIMIT_UNDER_RAIN’ during
‘DELAY_FOR_RAIN_OVSPD_RPT’ under rain.
71 = Alert when the vehicle’s speed becomes less than
‘SPEED_LIMIT_UNDER_RAIN’ under rain after alerting ‘70’. ‘
72 = Alert when the vehicle’s speed becomes less than
‘SPEED_LIMIT_UNDER_RAIN’ after alerting ‘70’ and stopping rain.
73 = Alert when the vehicle is inside a circle geo-fence and it’s speed
exceeds ‘GEO_SPD_LIMIT’ during ‘GEO_SPD_LIMIT_DEBOUNCE’.
74 = Alert when the vehicle’s speed returns less ‘GEO_SPD_LIMIT;
during ‘GEO_SPD_LIMIT_DEBOUNCE’ after alert ‘73’.

Please refer below note for report format of alert 1, 2, 70, 71, 72, 73 and
74.

H_METER String Driving hour-meter

BCK_VOLT String Voltage value of backup battery
MSG_TYPE 1 char Report is real time (1), Report is storage (0)
DID 14 char. Driver ID (inserted I-button ID ). Only for ST340UR
DID_REG 1 char. State of DID’s registration. Only for ST340UR
‘0’ = not registered. ‘1’ = registered.
CELL_ID String Information of Cell ID
MCC String Information of Mobile Country Code
MNC String Information of Mobile Network Code
RX_LVL String Information of Rx Level
LAC String Information of Location Area Code

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 51 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

TM_ADV String Information of Timing Advance

FORCE [X/256]G Value of force when DPA Alert. This value is only for alert “46”,”47” and
“48”
GEO ID 001 up to 200 For alert ID 73 and 74
MAX_SPD Km/h For alert ID 1, 2, 70, 71, 72, 73 and 74
SET_SPD Km/h For alert ID 1, 2, 70, 71, 72, 73 and 74.
Value of SPD_LIMIT_UNDER_RAIN or GEO_SPD_LIMIT.
*40,41,44 and 45 are optional functions . (Not the standard specifications)

*46,47,and 48 are optional functions to analyze the ‘Driver Pattern’.

<Example>
ST300ALT;100850001;01;302;20181017;07:41:56;2F100;+37.478519;+126.886819;000.007;000.00;9;1;
0;12.14;000000;1;0;3.8;1;012497F1160000;1;73;01c2;00;-82;20;1

<Note>

ALERT_ID 13 may be reported if the Back-up Battery cannot be charged or cannot be supported for long time
enough in case the Main Power source (vehicle’s battery) is disconnected.

The “H_METER/ BCK_VOLT/ MSG_TYPE” is included in alert report only when “HBM_STT” is “1”.
CELL_ID to TM_ADV are included in STT only when “HBM_STT” is “2”.

ALERT_ID 1, 2, 70, 71 and 72 includes configured speed limit (or speed limit under rain) and maximum speed
during over-speed condition including delay.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 52 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

5-4-2. Zip

Field Marks Meaning

STX 0x02 Start of zip data
PKT_LEN 2 Bytes Length of zip data, HDR to MSG_TYPE
HDR 0x13 Header of Alert Report
DEV_ID 5 bytes Device ID
BCD format

If the Device ID is 123456789, this field will be filled with 0x12, 0x34,
0x56 0x78 and 0x90.
MODEL 1byte Device Model (According to table model)
SW_VER 2 bytes
Bit 15 ~ Bit 12 Bit 11 ~ Bit 0
Version letter Version Number

Version letter represents alphabet following version number.

The range of this from ‘A’ to ‘O’.
The other bits field means version number.
The range of this is from 0 to 4095.
th th
If the version has no alphabet, bits from 12 to 15 should be zero.
Ex) 6139
6 means ‘F’, and 139 means V313.
DATE_TIME 6 bytes GPS date & Time (Year + Month + Day + Hour + Minute + Second)
CELL 3 bytes Location Code ID (2 Bytes) + Serving Cell BSIC (1 Byte)
LAT 4 bytes 1 byte (integer) + 3 bytes (BCD)
LON 4 bytes 1 byte (integer) + 3bytes (BCD)
SPD 3 bytes 2 bytes (integer) + 1 byte (BCD)
CRS 3 bytes 2 bytes (integer) + 1 byte (BCD)
SATT_FIX 1 byte
Bit 7 Bit 6 Bit 5 Bit 4 ~ Bit 0
Fix Latitude Longitude Satellite’s count
+/- sign +/- sign
+ sign = 0, - sign = 1

DIST 4 byte Traveled distance in meter

PWR_VOLT 2bytes Voltage value of main power
1 byte (integer) + 1 byte (BCD)
I/O 1 byte
Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
‘0’ Out1 ‘0’ Input 2 Input1 Ignition
Ignition : ‘1’ (ON), ‘0’ (OFF)
Input1 ~ Input2 : ‘1’ (Ground, Shorted), ‘0’ (Opened)
Out1 : ‘1’ (Active), ‘0’ (Inactive)
ALERT_ID 1 char. Alert type
0x01 ~ 0x32
H_METER 4bytes Driving hour-meter
BCK_VOLT 2bytes Voltage value of backup battery
MSG_TYPE 1 char Report is real time (1), Report is storage (0)
DID 7 bytes Driver ID (inserted I-button ID )
DID_REG 1 byte State of DID’s registration.
0 = not registered. 1 = registered.
CELL_ID 2 bytes Information of Cell ID
MCC 2 bytes Information of Mobile Country Code
Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 53 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

MNC 1 byte Information of Mobile Network Code

RX_LVL 2 bytes Information of Rx Level
LAC 2 bytes Information of Location Area Code
TM_ADV 1 bytes Information of Timing Advance
FORCE 4 Bytes 1 byte (integer) + 3 bytes (BCD)
Value of force when DPA Alert. This value is only for alert “46”,”47” and
“48”
GEO ID 2 bytes For alert ID 73 and 74. MSB
MAX_SPD 3 bytes 2 bytes (integer) + 1 byte (BCD)
SET_SPD 3 bytes 2 bytes (integer) + 1 byte (BCD)
ETX 0x03 End of zip data.

<Example>

Original String :

ST300ALT;100850001;01;313F;20181017;07:41:56;2F100;+37.478519;+126.886819;000.007;000.00;9;1;
0;12.14;000000;1;0;3.8;1;012497F1160000;1;73;01c2;00;-82;20;1

Zip Packet

0x02
0x00 0x3c
0x13
0x10 0x08 0x50 0x00 0x10
0x01
0x61 0x39
0x14 0x0a 0x11 0x07 0x29 0x38
0x02 0xF1 0x00
0x25 0x47 0x85 0x19
0x7e 0x88 0x68 0x19
0x00 0x00 0x07
0x00 0x00 0x00
0x89
0x00 0x00 0x00 0x00
0x0c 0x14
0x00 0x00
0x01
0x00
0x03 0x08
0x01
0x01 0x24 0x97 0xF1 0x16 0x00 0x01
0x00 0x49
0x01 0xc2
0x00
0xff 0xae
0x00 0x14
0x01
0x03

<Note>

ALERT_ID 13 may be reported if the Back-up Battery cannot be charged or cannot be supported for long time
enough in case the Main Power source (vehicle’s battery) is disconnected.
Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 54 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

The “H_METER/ BCK_VOLT/ MSG_TYPE” is include in alert report only when “HBM_STT” is “1”
CELL_ID to TM_ADV are included in STT only when “HBM_STT” is “2”.

ALERT_ID 1, 2, 70, 71 and 72 includes configured speed limit (or speed limit under rain) and maximum speed
during over-speed condition including delay. Maximum speed can be read from GPS or odometer depending on
ODO_USE option.
These flow alert ID as below.
… [ALERT ID] ; [SPD LIMIT UNDER RAIN] ; [GPS MAX SPD] ; [H METER] ; …

ALERT_ID 1 byte Alert type

0x01 ~ 0x44
GPS MAX SPD 3 bytes 2 bytes (integer) + 1 byte (BCD)
SPD LIMIT UNDER RAIN 3 bytes 2 bytes (integer) + 1 byte (BCD)
…

ALERT_ID 73 and 74 includes geo-fence ID, configured speed limit (GEO_SPD_LIMIT) and read maximum
speed from GPS during de-bouncing time (in case of ’73) or over-speed duration (in case of ’74’).
These flow alert ID as below.
… [ALERT ID] ; [GEO ID] ; [GEP SPD LIMIT] ; [GPS MAX SPD] ; [H METER] ; …

ALERT_ID 1 byte Alert type

0x01 ~ 0x44
OVSPD GEO_ID 2 byte
GPS MAX SPD 3 bytes 2 bytes (integer) + 1 byte (BCD)
GEP SPD LIMIT 3 bytes 2 bytes (integer) + 1 byte (BCD)
…

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 55 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

5-5. Travel Event Report

Device sends ‘Travel Event’ to the server as defined by user in the course of setting the telemetry parameters. This
event is sending when the vehicle is parked.

HDR DEV_ID MODEL SW_VER DATE TIME DIST PWR_VOLT H_METER BCK_VOLT

MSG_TYPE TRAVEL_DIST TRAVEL_TIME TIME_STOP TIME_MOVING LAT_TRAVEL_ST

LON_TRAVEL_ST LAT_TRAVEL_FI LON_TRAVEL_FI AVERAGE_SPD MAX_SPD TIME_OVER_SPD

TIME_ECO_UP TIME_ECO_DOWN TIME_ECO_INSIDE TIME_ECO_INSIDE TIME_OVER_RPM

TIME_DC DRIVER_ID

5-5-1. Normal

Field Definitions Remark

HDR “ST300HTE” Header of Travel Event Report
DEV_ID 9 char. Device ID
MODEL 2 Char Device Model (According to table model)
SW_VER String Main version : number
Derived version : alphabet from ‘A’ to ‘O’
Ex) “313”, “313F”
DATE 8 char. GPS date (yyyymmdd)
Year + Month + Day
TIME 8 char. GPS time (hh:mm:ss)
Hour : Minute : Second
DIST String Traveled distance in meter
PWR_VOLT String Voltage value of main power
H_METER String Driving hour-meter **
BCK_VOLT String Voltage value of backup battery **
MSG_TYPE 1 char Report is real time (1), Report is storage (0) **
TRAVEL_DIST String Traveled distance during this travel(in meter)
TRAVEL_TIME String Time of this travel (in minute)
TIME_STOP String Duration of stop in this travel (in minute)
TIME_MOVING String Duration of moving in this travel (in minute)
LAT_TRAVEL_ST String Latitude of start position of this travel (+/-xx.xxxxxx)
LON_TRAVEL_ST String Longitude of start position of this travel (+/-xxx.xxxxxx)
LAT_TRAVEL_FI String Latitude of end position of this travel (+/-xx.xxxxxx)
LON_TRAVEL_FI String Longitude of end position of this travel(+/-xxx.xxxxxx)
AVERAGE_SPD String Average speed in this travel(in km/h)
MAX_SPD String Maximum speed in this travel (in km/h)
TIME_OVER_SPD String Accumulated time that the car exceeded over-speed in this travel.
(in minute)
DRIVER_ID String Inserted driver ID
<example>
** field can be displayed although HBM_STT option is not ‘0’.
ST300HTE;100850001;04;248;20110101;00:13:52;167559;12.28;004005;0.0;1;0;3;3;0;-22.881018;-047.070831
;-22.881018;-047.070831;000.000;000.000;0;0;3;0;0;0;01E04D44160000

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 56 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

5-5-2. Zip

Field Definitions Remark

STX 0x02 Start of zip data
PKT_LEN 2 Bytes Length of zip data, HDR to MSG_TYPE
HDR 0x1B Header of Travel Event Report
DEV_ID 5 bytes Device ID
BCD format
If the Device ID is 123456789, this field will be filled with 0x12, 0x34,
0x56 0x78 and 0x90.
MODEL 1byte Device Model (According to table model)
SW_VER 2 bytes
Bit 15 ~ Bit 12 Bit 11 ~ Bit 0
Version letter Version Number

Version letter represents alphabet following version number.

The range of this from ‘A’ to ‘O’.
The other bits field means version number.
The range of this is from 0 to 4095.
th th
If the version has no alphabet, bits from 12 to 15 should be zero.
Ex) 6139
6 means ‘F’, and 139 means V313.
DATE_TIME 6 bytes GPS date & Time (Year + Month + Day + Hour + Minute + Second)
DIST 4 byte Traveled distance in meter
PWR_VOLT 2bytes Voltage value of main power
1 byte (integer) + 1 byte (BCD)
H_METER 4bytes Driving hour-meter
BCK_VOLT 2bytes Voltage value of backup battery
MSG_TYPE 1 byte Report is real time (1), Report is storage (0)
TRAVEL_DIST 3bytes Traveled distance during this travel(in meter)
TRAVEL_TIME 2bytes Time of this travel (in minute)
TIME_STOP 2bytes Duration of stop in this travel (in minute)
TIME_MOVING 2bytes Duration of moving in this travel (in minute)
LAT_TRAVEL_ST 4bytes Latitude of start position of this travel (+/-xx.xxxxxx)
1 byte (integer) + 3 bytes (BCD)
LON_TRAVEL_ST 4bytes Longitude of start position of this travel (+/-xxx.xxxxxx)
1 byte (integer) + 3 bytes (BCD)
LAT_TRAVEL_FI 4bytes Latitude of end position of this travel (+/-xx.xxxxxx)
1 byte (integer) + 3 bytes (BCD)
LON_TRAVEL_FI 4bytes Longitude of end position of this travel(+/-xxx.xxxxxx)
1 byte (integer) + 3 bytes (BCD)
POS_SIGN 1byte Minus sign of travel positions
Bit 3 Bit 2 Bit 1 Bit 0
Travel start Travel start Travel stop Travel stop
latitude longitude latitude longitude
+/- sign +/- sign +/- sign +/- sign
+ sign = 0, - sign = 1
AVERAGE_SPD 3bytes Average speed in this travel(in km/h)
2 bytes (integer) + 1 byte (BCD)
MAX_SPD 3bytes Maximum speed in this travel (in km/h)
2 bytes (integer) + 1 byte (BCD)
TIME_OVER_SPD 2bytes Accumulated time that the car exceeded over-speed in this travel.
(in minute)

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 57 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

TIME_DC 2bytes Accumulated time that the vehicle was driven putting the gear in dead
center in this travel. (in minute)
DRIVER_ID 7bytes Inserted driver ID. BCD format
ETX 0x03 End of zip data
<example>
ST300HTE;600850777;04;313F;20110101;00:01:10;151229;12.07;000669;0.0;1;135010;351;21;330;
-22.881018;-047.130831;-22.882034;-047.087123;035.350;096.480;3;5;12;334;7;0;01E04D44160000

Field Data in string format Data in ZIP format

STA 0x02
PKTLEN 0x00 0x4f
HDR “ST300HTE” 0x1b
DEV_ID 600850777” 0x60 0x08 0x50 0x77 0x70
MODEL “04” 0x04
SW_VER “313F” 0x61 0x39
DATE_TIME “20140428” “00:13:52” 0x0e 0x04 0x1c 0x00 0x0d 0x34
DIST “151227” 0x00 0x02 0x4e 0xbb
PWR_VOLT “12.11” 0x0c 0x11
H_METER “000662” 0x00 0x00 0x02 0x96
BCK_VOLT “0.0” 0x00 0x00
MSG_TYPE “1” 0x01
TRAVEL_DIST “135010” 0x02 0x0f 0x62
TRAVEL_TIME “351” 0x01 0x5f
TIME_STOP “21” 0x00 0x15
TIME_MOVING “330” 0x01 0x4a
LAT_TRAVEL_ST “-22.881018” 0x16 0x88 0x10 0x18
LON_TRAVEL_ST “047.130831” 0x2f 0x13 0x08 0x31
LAT_TRAVEL_FI “-22.882034” 0x16 0x88 0x20 0x34
LON_TRAVEL_FI “-047.087123” 0x2f 0x08 0x71 0x23
POS_SIGN 0x0f
AVERAGE_SPD “035.350” 0x00 0x23 0x35
MAX_SPD “096.480” 0x00 0x60 0x48
TIME_OVER_SPD “3” 0x00 0x03
DRIVER_ID “01E04D44160000” 0x01 0xe0 0x4d 0x44 0x16 0x00 0x00

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 58 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

5-6. Keep-Alive Report

A typical GSM/GPRS service provider in any countries has its own corporate policy restricting connection time of
device with the GSM/GPRS networks only at an interval if device does not communicate with its server for a long
time, which is 1 hour, for instance. The time length varies depending upon such service provider. Please check it
by asking your GSM/GPRS service provider this question in your country.

In a casethat there has not been any communication between device and server for such a time period, the
GSM/GPRS service provider would not provide GSM/GPRS service for the device temporarily. To avoid such a
case, device sends the server this ‘Keep-Alive’ Report at an interval, ‘T4’ (‘Keep-Alive’ interval named in ‘SyncTrak’
and in this document), which is shorter than the 60 minutes. User of the device may adjust the value of ‘T4’ as
desired.

This Report is intended to mean that the device is still alive and ready for any possible communications with the
server for that long time (‘T4’) even though the device does not interact temporarily with the server.

5-6-1. Normal

HDR DEV_ID

Field Marks Meaning

HDR “ST300ALV” Header of Alive report
DEV_ID 9 char. Device ID
<Example>
ST300ALV;100850000

5-6-2. Zip

Field Marks Meaning

STX 0x02 Start of zip data
PKT_LEN 2 Bytes Length of zip data, HDR to DEV_ID
HDR 0x14 Header of Alive report (1 byte)
DEV_ID 5 bytes Device ID
BCD format

ETX 0x03 End of zip data

<Example>
0x02 0x00 0x06 0x14 0x10 0x08 0x50 0x00 0x00 0x03

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 59 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

5-7.Data Report from External RS232

If device is connected with external appliance by RS232, it receives data from the appliance and sends the data to
the server. Data transfer is made with below string.

HDR DEV_ID MODEL SW_VER DATE TIME CELL LAT

LON SPD CRS SATT FOX DIST PWR_VOLT I/O
LEN DATA H_METER BCK_VOLT MSG_TYPE CHK_SUM

5-7-1. Normal

Field Marks Meaning

HDR “ST300UEX” Report Header of External Device’s Data
DEV_ID 9 char. Device ID
MODEL 2Char Device Model (According to table model)
SW_VER String Main version : number
Derived version : alphabet from ‘A’ to ‘O’
Ex) “313”, “313F”
DATE 8 char. GPS date (yyyymmdd)
TIME 8 char. GPS time (hh:mm:ss)
CELL String Location Code ID(3 digits hex) + Serving Cell BSIC(2 digits decimal)
LAT String Latitude (+/-xx.xxxxxx)
LON String Longitude (+/-xxx.xxxxxx)
SPD String Speed in km/h
CRS String Course over ground in degree
SATT String Number of satellites
FIX ‘1’ or ‘0’ GPS is fixed (1), GPS is not fixed (0)
DIST String Traveled distance in meter
PWR_VOLT String Voltage value of main power
I/O 6 char. Current I/O status of inputs and outputs.
Ignition + Input1 + Input 2 + ‘0’ + Out1 + ‘0’
Ignition : ‘1’ (ON), ‘0’ (OFF)
Input1 ~ Input2 : ‘1’ (Ground, Shorted), ‘0’ (Opened)
Out1 : ‘1’ (Active), ‘0’ (Inactive)
LEN String Length of Data
DATA Data from external RS232 device
Up to 500 bytes
CHK_SUM String 8bit Checksum. Summation of DATA
H_METER String Driving hour-meter
BCK_VOLT String Voltage value of backup battery
MSG_TYPE 1 char Report is real time (1), Report is storage (0)
DID 14 char. Driver ID (inserted I-button ID ). Only for ST340UR
DID_REG 1 char. State of DID’s registration. Only for ST340UR
‘0’ = not registered. ‘1’ = registered.
CELL_ID String Information of Cell ID
MCC String Information of Mobile Country Code
MNC String Information of Mobile Network Code
RX_LVL String Information of Rx Level
LAC String Information of Location Area Code
TM_ADV String Information of Timing Advance

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 60 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

<Example>
ST300UEX;100850000;01;010;20081017;07:41:56;2F100;+37.478519;+126.886819;000.012;000.00;9;1;0;15.3
0;001100;25;Welcome to Suntech World!;12;0;4.5;1
5-7-2. Zip

Field Marks Meaning

STX 0x02 Start of zip data
PKT_LEN 2 Bytes Length of zip data, HDR to MSG_TYPE
HDR 0x16 Report Header of External Device’s Data
DEV_ID 5 bytes Device ID
BCD format

If the Device ID is 123456789, this field will be filled with 0x12, 0x34,
0x56 0x78 and 0x90.
MODEL 1byte Device Model (According to table model)
SW_VER 2 bytes
Bit 15 ~ Bit 12 Bit 11 ~ Bit 0
Version letter Version Number

Version letter represents alphabet following version number.

The range of this from ‘A’ to ‘O’.
The other bits field means version number.
The range of this is from 0 to 4095.
th th
If the version has no alphabet, bits from 12 to 15 should be zero.
Ex) 6139
6 means ‘F’, and 139 means V313.
DATE_TIME 6 bytes GPS date & Time (Year + Month + Day + Hour + Minute + Second)
CELL 3 bytes Location Code ID (2 Bytes) + Serving Cell BSIC (1 Byte)
LAT 4 bytes 1 byte (integer) + 3 bytes (BCD)
LON 4 bytes 1 byte (integer) + 3bytes (BCD)
SPD 3 bytes 2 bytes (integer) + 1 byte (BCD)
CRS 3 bytes 2 bytes (integer) + 1 byte (BCD)
SATT_FIX 1 byte
Bit 7 Bit 6 Bit 5 Bit 4 ~ Bit 0
Fix Latitude Longitude Satellite’s count
+/- sign +/- sign
+ sign = 0, - sign = 1

DIST 4 bytes Traveled distance in meter

PWR_VOLT 2bytes Voltage value of the Main Power
1 byte (integer) + 1 byte (BCD)
I/O 1 byte
Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
‘0’ Out1 ‘0’ Input 2 Input1 Ignition
Ignition : ‘1’ (ON), ‘0’ (OFF)
Input1 ~ Input2 : ‘1’ (Ground, Shorted), ‘0’ (Opened)
Out1 : ‘1’ (Active), ‘0’ (Inactive)
LEN 2 bytes Length of Data
DATA Data from external RS232 device
Up to 500 bytes
CHK_SUM 1 byte 8bit Checksum. Summation of Data
H_METER 4bytes Driving hour-meter
BCK_VOLT 2bytes Voltage value of backup battery
Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 61 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

MSG_TYPE 1 char Report is real time (1), Report is storage (0)

DID 7 bytes Driver ID (inserted I-button ID )
DID_REG 1 byte State of DID’s registration.
0 = not registered. 1 = registered.
CELL_ID 2 bytes Information of Cell ID
MCC 2 bytes Information of Mobile Country Code
MNC 1 byte Information of Mobile Network Code
RX_LVL 2 bytes Information of Rx Level
LAC 2 bytes Information of Location Area Code
TM_ADV 1 bytes Information of Timing Advance
ETX 0x03 End of zip data.
<Example>

Original String :
ST300UEX;100850001;01;313F;20081017;07:41:56;2F100;+37.478519;+126.886819;032.012;000.00;9;1;500;
15.30;001100;25;Welcome to Suntech World!;12;0;4.5;1

Zip Packet
0x02
0x00 0x47
0x16
0x10 0x08 0x50 0x00 0x10
0x01
0x61 0x39
0x08 0x0a 0x11 0x07 0x29 0x38
0x02 0xF1 0x00
0x25 0x47 0x85 0x19
0x7e 0x88 0x68 0x19
0x00 0x20 0x01
0x00 0x00 0x00
0x89
0x00 0x00 0x01 0xF4
0x0F 0x30
0x0c
0x00 0x19
0x57 0x65 0x6C 0x63 0x6F 0x6D 0x65 0x20 0x74 0x6F 0x20 0x53 0x75 0x6E 0x74 0x65 0x63 0x68 0x20
0x57 0x6F 0x72 0x6C 0x64 0x21
0x12
0x00 0x00 0x00 0x00
0x04 0x05
0x01
0x03

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 62 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

5-8. Transferring Data to External RS232 Device

HDR DEV_ID VER LEN DATA CHK_SUM

● Definition : If the device receives this command, it transfers the data to connected RS232’s device.

Field Definitions Unit Remark

HDR “ST300DEX” Command type
DEV_ID 9 char. Device ID
VER “02” Protocol Version
LEN Length of data
DATA Up to 500bytes
CHK_SUM 8bit Checksum
<example>
[command] ST300DEX;100850000;02;6;012345;2F
[response] ST300DEX;Res;100850000;010;25;012345;2F

<note>
CHK_SUM is string converted from lower 8 bit of the summation of DATA field.
In case of above example.
Value of ‘0’ character in DATA field is equal to 0x30 in hex system, and ‘1’ is equal to 0x31 in hex system.
In this case, summation of DATA will be 0x12F (0x30+0x31+0x32+0x33+0x34+0x35), and CHK_SUM string will
be “2F’.
And, whole string from server will be “ST300DEX;100850000;02;6;012345;2F”.

If DATA field includes 0x00 or 0x01, server should convert and send as below.
Original Data : 0x30 0x31 0x00 0x32 0x01
Conversion : 0x30 0x31 0x01 0x10 0x32 0x01 0x11

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 63 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

5-9. Status String Reporting via SMS

5-9-1. In case of Back-up method

In case device is located in an area where it has good connectivity with GSM and without having good
connectivity with GPRS, it sends a string type report to its server. However, as soon as the bad
connectivity between GPRS and device gets back to normal, the device will try to send the reports to the
server.

HDR DEV_ID MODEL SW_VER

DATE1 TIME1 CELL1 LAT1 LON1 SPD1 CRS1 SATT1 FIX1 DIST1 PVOLT1 I/O1
DATE2 TIME2 CELL2 LAT2 LON2 SPD2 CRS2 SATT2 FIX2 DIST2 PVOLT2 I/O2
…

Note):
‘STT String ‘sent via SMS does not include the ‘message number field’.
Depending on HBM_STT option, additional field would added after I/O field.

5-9-2. In case of Main method

Device sends to its server ‘status string’ via SMS when it can be connected with the server only via SMS
without being connected with GPRS.

Refer to “Status Report” chapter.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 64 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

5-10. Location query sent via smart phone

If you are a smart phone user, you can use it to easily find the current location on the google map

Just send one of the following messages by your smart phone:

“Where are you”, “whereareyou”, “Where r u”, “whereru”

And, then the google map will be responding to you by sending the address on your smart phone. You
can see the current location of the device just by opening the message containing that address on the
web browser.

In order to enable device to accept your SMS message, you have to add your smart phone number to
one of the 4 optional numbers such asSMS_MT1 to SMS_MT4 or disable SMS_LOCK.
Refer to Chapter, “GSM Parameter Setting” for more details.
Before you start using this function, you should get to know the URL (server address) of the Google map
first.

You can have more information about how to get the server address of the Google map in section
“Command to Get Google Map Address” of this document.

You can also get more information about how to set the server address of the Google map in section
“Command to Set Google Map Address” of this document.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 65 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

6. Command for general use

After device is configured, user may need to check/query values of the parameters if he/she wants to change those
values. This chapter shows user how to change the parameters’ values that have been set already.

6-1. Common parts of this command

HDR DEV_ID VER CMD_ID

Field Marks Value Meaning

HDR “ST300CMD” Command type
DEV_ID 9 char. Device ID
VER ‘02’ Protocol Version
CMD_ID String

**Caution: If ‘Device ID’ is not correct, this command will be ignored by the device.

6-2. Requesting Status

Once this command is made, some interactions will be made between the server and the device as described in
the ‘Meaning’ section of the table below.

Field Mark Value Meaning

CMD_ID “StatusReq” Requesting Status of the device.

If device receives this ‘Request’ command from the server, it

sends the Status string to the server promptly.
<Example>

[command] ST300CMD;100850000;02;StatusReq

[response]
ST300STT;100850000;07;301;20060908;14:43:21;01454;+37.124975;+127.091003;000.000;158.53;10;1;0;12.
11;000000;1;0493

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 66 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

6-3. Pre-setting

Once this command is made, some interactions will be made between the server and the device as described in
the ‘Meaning’ section of the table below.

Field Mark Value Meaning

CMD_ID “Preset” Report parameters’ setting values and current device status

Response includes network, report, event, GSM and Service

parameters included in ‘SyncTrak’. It includes status of device
as well.
<Example>

[command] ST300CMD;100850000;02;Preset

[response] ST300CMD;Res;100850000;010;Preset;
NTW;0;internet;;;111.111.111.111;8600;;;;1234;
RPT;60;180;120;60;3;0;0;;;;
EVT;0;60;0;12;3;9;0;30;0;0;7;1;0;0;0;0;0;0;0;9;9;0;0;0;
GSM;0;;;;;0;;;;;;;;
SVC;1;120;0;0;0;0;1;1;1;0;0;0;0
DEV;0;0;0;0

<Note>

** After power is on, the device sends to the server response string of the ‘Preset’ once.

** The ‘DEVFiled’ informs the device of the current status as below.

OUT1 OUT2 PWR_DN BAT_CON
0 = Disable 0 = Disable 0 = Normal 0 = Backup battery is disconnected.
1 = Enable 1 = Enable 1 = Sleep 1 = Backup battery is connected.
2 = Deep sleep

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 67 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

Field Mark Value Meaning

CMD_ID “PresetA” Report all the parameters including additional parameter.
<Example>

[command] ST300CMD;100850000;02;Preset A

[response] ST300CMD;Res;100850000;010;PresetA;
NTW;0;internet;;;111.111.111.111;8600;;;;1234;
RPT;3600;180;120;60;3;0;0;;;;
EVT;0;60;0;12;3;9;0;30;0;0;7;1;0;0;0;0;0;0;0;9;9;0;0;0;
GSM;0;;;;;0;;;;;;;;
SVC;1;120;0;0;0;0;1;1;1;0;0;0;0;
ADP;U;T;2;9000;0;0;0;0;0;0;
MSR;10;0.10;0.10;0.70;
MBV;9.43;21.07;17.07;8.00;18.00;0.00;0.00;
NPT;0.0;0;30;0;0;500;300;5;10;70;5;10;70;0;
DEV;0;0;0;0;0;0;0;0;
AD2;30;50;10;0;0;0;0;0;0;0;0;0;0;0;0;
BAT;1;3.4;
HTP;1;0;0;0;0;0;0;0;;;0;0;0;10;0;
DPA;0;20.0;15.0;30.0;40.0;0;0

<Note>

** ‘DEV Filed’ informs the server about the current status of the device as below.

OUT1 OUT2 PWR_DN BAT_CON

0 = Disable 0 = Disable 0 = Normal 0 = Backup battery is disconnected.
1 = Enable 1 = Enable 1 = Sleep 1 = Backup battery is connected.
2 = Deep sleep

Anti-Theft
Reserved 0 = Disable Reserved Reserved
1 = Enable

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 68 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

6-4. ACK of Emergency

Once this command is made by the server, the device will stop reporting about the occurrence of
emergency. More details are described in the ‘Meaning’ section of the table below.

Field Mark Value Meaning

CMD_ID “AckEmerg” ‘Acknowledge’ of emergency report

The server sends device this command as a response to

inform the device that the server has completed receiving all
the ‘emergency reports’. And then, the device will stop
sending Emergency reports if it is in emergency state.
<Example>
[command] ST300CMD;100850000;02;AckEmerg
[response] ST300CMD;Res;100850000;010;AckEmerg

6-5. Re-setting (Restoring to factory defaults and Rebooting)

Once this command is made, some interactions will be made between the server and the device as described in
the ‘Meaning’ section of the table below.

Field Mark Value Meaning

CMD_ID “Reset” Re-setting the current parameters’ values

This command is used to initialize all the parameters with the

values set in the factory of the devices and to reboot the
device.
<Example>

[command] ST300CMD;100850000;02;Reset

[response] ST300CMD;Res;100850000;010;Reset

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 69 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

6-6. Enable1 (‘Activating Output 1’)

Field Mark Value Meaning

CMD_ID “Enable1” Enable Output1
<Example>
[command] ST300CMD;100850000;02;Enable1
[response] ST300CMD;Res;100850000;010;Enable1
[response] ST300CMD;Res;100850000;010;Enable1NoUse (in case that IN type is set to ‘No Use’).

<Note>
** Output1 line goes to active status.

** If OUT1 is set with immobilizer, output1 line goes to the Active Status gradually with pulse in driving mode.

** If OUT1 is set with pulse type, output1 line generates pulse and automatically returns to the Inactive State
after pulsing out.

6-7. Disable1 (‘Inactivating Output1’)

Field Mark Value Meaning

CMD_ID “Disable1” Disable Output1
<Example>
[command] ST300CMD;100850000;02;Disable1
[response] ST300CMD;Res;100850000;010;Disable1
[response] ST300CMD;Res;100850000;010;Disable1NoUse (in case that IN type is set to ‘No Use’).

<Note>
** Output1 line goes to the Inactive Status.

6-8. Requesting IMSI

Once this command is made, some interactions will be made between the server and the device as described in
the ‘Meaning’ section of the table as below.

Field Mark Value Meaning

CMD_ID “ReqIMSI” The server sends the device this command requesting IMSI
(International Mobile Subscriber Identity) if the server wants to
receive IMSI from the device.)
If the device receives the command from the server, it sends
the IMSI to the server.
<Example>

[command] ST300CMD;100850000;02;ReqIMSI
[response] ST300CMD;Res;100850000;010;ReqIMSI;724031111553779

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 70 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

6-9. Requesting ICCID

Once this command is made, some interactions will be made between the server and the device as described in
the ‘Meaning’ section of the table as below.

Field Mark Value Meaning

CMD_ID “ReqICCID”  How to request ICCID (Integrated Circuit Card Identifier),
which is a sequence number that is displayed on SIM

If device receives this command, it sends the server ICCID.

<Example>

[command] ST300CMD;100850000;02;ReqICCID
[response] ST300CMD;Res;100850000;010;ReqICCID;89550230000084256668

6-10. Requesting IMEI

Field Mark Value Meaning

CMD_ID “ReqIMEI” Requesting IMEI of the device

If the device receives this command, it reports IMEI to the

server.
<Example>

[command] ST300CMD;100850000;02;ReqIMEI
[response] ST300CMD;Res;100850000;301;ReqIMEI;356430073101123

6-11. Requesting Version

Once this command is made, some interactions will be made between the server and the device as described in
the ‘Meaning’ section of the table as below.

Field Mark Value Meaning

CMD_ID “ReqVer” Requesting version of the device

If the device receives this command, it reports to the server

about: Model, Buyer, Protocol and Software(S/W) release
version.
<Example>

[command] ST300CMD;100850000;02;ReqVer
[response] ST300CMD;Res;100850000;300;ReqVer;ST340UR(M001)_SUNTECHBR_STADV_300

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 71 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

6-12Status Request made by External device connected with RS232 of Event Lines

This command is made towards ST300 by the external device connected with RS232 of the event line. Once the
ST300 receives this command, some interactions will be made between the external device and the ST300 as
described in the ‘Meaning’ section of the table as below.

HDR DEV_ID VER LEN DATA CHK_SUM

Field Mark Value Meaning

CMD_ID “SttReq” Status request
If received, the device sends status string instantly.
<Example>

[command] SttReq
[response]
ST300STT;100850000;01;010;20090724;07:12:16;00129;+37.479995;+126.885815;000.029;000.00;
7;1;0;15.33;100000;2;0002

6-13 AT Commands from RS232

HDR AT COMMAND CR/LF

● Definition : Controls some functions

Field Definitions Unit Remark

HDR “ATCMD” Header
AT COMMAND General AT Commands string
CR/LF 0x0d0x0a Mark of End [Carriage Return \ Line Feed]

<example>
[command]
ATCMD;AT+CGREG? CR\LF
[response]
+CGREG: 0, 1
OK

Note.
We can support to the most of at commands except SMS commands.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 72 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

7. Command for non-general use

Description on each factor necessary to make types of these commands is shown in this Chapter.

HDR DEV_ID VER CMD_ID

Field Marks Value Meaning

HDR “ST300CMD” Command type
DEV_ID 9 char. Device ID
VER ‘01’ Protocol Version
CMD_ID String Control command content

Commands are classified into two groups such as:

 “Commands for General Use”, which have already been explained in the previous chapter, Chapter 8,
 “Commands for Non-general Use”.

The latter commands are described here as below.

7-1. Erase All

This command is used if you want to erase all the saved reports and disable the outputs.

Field Mark Value Meaning

CMD_ID “EraseAll” This command is used if you want to erase all the saved
reports and disable the outputs.
This command is needed to initialize the device whichis to be
delivered to a new customer.
<Example>

[command] ST300CMD;100850000;02;EraseAll
[response] ST300CMD;Res;100850000;010;EraseAll

7-2. Initialize Traveled Distance

● Definition : Initialize the travel distance.

Field Definitions Unit Remark

CMD_ID “InitDist” meter Set odometer to 0.
<example>
[command] ST300CMD;600850000;02;InitDist
[response] ST300CMD;Res;600850000;262;InitDist

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 73 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

7-3. Setting Traveled Distance

This command is used if you want to set the travelled distance.

Field Mark Value Meaning

CMD_ID “SetOdometer=” meter Setting odometer.
<Example>

[command] ST300CMD;100850000;02;SetOdometer=999999999
[response] ST300CMD;Res;100850000;010;SetOdometer=999999999

7-4. Initializing Message Number

This command is used if you want to initialize sequence number of the message.

Field Mark Value Meaning

CMD_ID “InitMsgNo” Set message number to 0.
<Example>

[command] ST300CMD;100850000;02;InitMsgNo
[response] ST300CMD;Res;100850000;010;InitMsgNo

7-5. Setting Hour-Meter

This command is used if you want to set the travelled time period.

Field Mark Value Meaning

CMD_ID “SetHMeter=” minute What to set the travelled time period.
<Example>
[command] ST300CMD;100850000;02;SetHMeter=999999
[response] ST300CMD;Res;100850000;010;SetHmeter=999999
Max value is ‘999999’

7-6. Initialize Circular Geo-fence

● Definition : Request all of geo-fence parameters.

Field Definitions Unit Remark

CMD_ID “InitCircleGeo” Clear circular geo-fences.
<example>
[command] ST300CMD;600850000;02;InitCircleGeo
[response] ST300CMD;Res;600850000;262;InitCircleGeo

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 74 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

7-7. Requesting Circular Geo-fence

This command is used if the device is required to report to the server with all of the geo-fence parameters that are
pre-set.

Field Mark Value Meaning

CMD_ID “ReqCircleGeo”  Report the enabled circular geo-fences
 Response consists of continuous field (0 or 1) and
information about all the geo-fences including the
first geo-fence up to the last one whose last digit is 1
(One).
<Example>
[command] ST300CMD;100850000;02;ReqCircleGeo
[response] Case that unit has 3 geo-fences :
ST300CMD;Res;205310317;301;ReqCircleGeo;1;1;1;37.478809;126.887890;191;1;1;100;5
ST300CMD;Res;205310317;301;ReqCircleGeo;1;2;1;37.566190;126.977330;177;1;1;80;10
ST300CMD;Res;205310317;301;ReqCircleGeo;0;3;1;37.565654;126.966462;267;0;1;80;20

Case that unit has no geo-fence.

ST300CMD;Res;205310317;301;ReqCircleGeo;NoData

<Notes>
** Continuous field of above response string represents bold.

7-8. Requesting Own Phone Number

Once this command is made, some interactions will be made between the server and the device as described in
the ‘Meaning’ section of the table as below.

Field Mark Value Meaning

CMD_ID “ReqOwnNo” Requesting own phone number
<Example>
[command] ST300CMD;100850000;02;ReqOwnNo
[response] ST300CMD;Res;100850000;010;ReqOwnNo;82220275656

<Notes>
** When the device has no SIM or is under power-on process, the own phone number cannot be read.
The device reports with “NotReady”

** If the own number field in SIM is empty, the device reports with “NoData”.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 75 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

7-9. Setting Own Phone Number

Once this command is made, some interactions will be made between the server and the device as described in
the ‘Meaning’ section of the table as below.

Field Mark Value Meaning

CMD_ID “SetOwnNo”  How to set the own phone number
This command is followed by “=” and own number.
<Example>
[command] ST300CMD;100850000;02;SetOwnNo=21140108
[response] ST300CMD;Res;100850000;010;SetOwnNo=21140108

<Notes>
** When the device has no SIM or is under power-on process, the own phone number cannot be set.
The device reports with “NotReady”

7-10. Command to Reboot

This command is made by the server to the device which needs to be reboot.

Field Mark Value Meaning

CMD_ID “Reboot” Reboot device.
<Example>
[command] ST300CMD;100850000;02;Reboot
[response] ST300CMD;Res;100850000;010;Reboot

7-11. Setting ImproveBatteryLife

● Definition : Setting Improve Battery Life.

Field Definitions Unit Remark

CMD_ID “ImproveBatteryLife” 0 = Disable ImproveBatteryLife
1 = Enable ImproveBatteryLife
<example>
[command] ST300CMD; 600850000;02;ImproveBatteryLife=0
[response] ST300CMD;Res; 600850000;010;ImproveBatteryLife=0;OK

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 76 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

7-12. Request ImproveBatteryLife

● Definition : Request Improve Battery Life.

Field Definitions Unit Remark

CMD_ID “ReqBattLife” Request Improve Battery Life
<example>
[command] ST300CMD;600850000;02;ReqBattLife
[response] ST300CMD;Res;600850000;534;ReqBattLife;1

7-13. Command on How to Restart Anti-Theft 2

Field Definitions Unit Remark

CMD_ID “RestartAntiTheft2” Restart anti-theft after anti-theft disabled by press of panic
button in case of ‘Anti-theft 2’.
<Example>
[command] ST300CMD;600850000;02;RestartAntiTheft2
[response] ST300CMD;Res;600850000;010; RestartAntiTheft2

<Note>
This command is only for ‘Anti-theft 2’ mode.

7-14. Command on How to Set SMS Number for Panic Situation

This table shows us how to set the SMS number to be used when the panic button is pressed.

Field Mark Value Meaning

CMD_ID “SetSMSNoOfPanic” How to set the SMS number where the location information
(i.e. the location link address) will be delivered through SMS
when the panic button is pressed.
<Example>
[command] ST300CMD;100850000;02;SetSMSNoOfPanic=01988888888
[response] ST300CMD;Res;100850000;010;SetSMSNoOfPanic=01988888888

7-15. Requesting SMS Number Used in Panic Situation

This table shows us how to get the SMS number when the panic button is pressed.

Field Mark Value Meaning

CMD_ID “ReqSMSNoOfPanic” Requesting SMS number where the location link address is
sent when the panic button is pressed.
<Example>
[command] ST300CMD;100850000;02;ReqSMSNoOfPanic
[response] ST300CMD;Res;100850000;010;ReqSMSNoOfPanic;NoData

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 77 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

7-16. Command to Set Google Map Address

In a case that you use a smart phone operating a function of “Where Are You”, you can use the server of the
Google as set below in italic bold letters, “Google map address”. The users of the Google map should check what
the right map address of the Google is and that the right address should be set. The Google map address needs to
be checked. If the Google map address is not right, this function (“Where Are You”) cannot be used.

Field Mark Value Meaning

CMD_ID “SetGoogleMap” Set location link address format (Google map address).
This command is either followed by “=” or inserted inside the
address.
<Example>
[command] ST300CMD;100850000;02;SetGoogleMap=http://maps.google.com/maps?q=
[response] ST300CMD;Res;100850000;010; SetGoogleMap=http://maps.google.com/maps?q=

[command] ST300CMD;100850000;02;SetGoogleMap=http://maps.google.com/[Lon],[Lat]/maps?q
[response] ST300CMD;Res;100850000;010;SetGoogleMap=http://maps.google.com/[Lon],[Lat]/maps?q

<Note>
The max of input string is 96 characters.

7-17. Command to Get Google Map Address

In case this command is made, the pre-set existing Google Map address will be known.
Get Google Map Address.

Field Mark Value Meaning

CMD_ID “ReqGoogleMap” Request the Google Map Address.
This command is followed by “=” and Google Map Address.
<Example>
[command] ST300CMD;100850000;02;ReqGoogleMap
[response] ST300CMD;Res;100850000;010;ReqGoogleMap;http://maps.google.com/maps?q=

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 78 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

7-18. Changing Direction of SMS response

Field Mark Value Meaning

CMD_ID “SetSmsResDir” 0~2 Change direction of SMS response

When a command is transmitted by SMS, device send its

response by SMS, GPRS or both.

0: Response is sent by SMS

1: Response is sent by GPRS
2: Response is sent by both SMS and GPRS
<Example>

[command] ST300CMD;100850000;02;SetSmsResDir=0
[response] ST300CMD;Res;100850000;301;SetSmsResDir=0

7-19. Requesting Direction of SMS response

Field Mark Value Meaning

CMD_ID “ReqSmsResDir” 0~2 Requesting direction of SMS response

If the device receives this command, it reports direction of

SMS response

0: SMS responses are sent through SMS only.

1: SMS responses are sent through GPRS only.
0: SMS responses are sent through both SMS and GPRS.
<Example>

[command] ST300CMD;100850000;02;ReqSmsResDir
[response] ST300CMD;Res;100850000;301; ReqSmsResDir;0

7-20. Request Driver ID

● Definition : Request current inserted driver ID

Field Definitions Unit Remark

CMD_ID “ReqDriverID” Request inserted driver ID
<example>
[command] ST300CMD;;02;ReqDriverID
[response]ST300CMD;Res;100850000;267;ReqDriverID;0100004E160000
ST300CMD CMD;Res;100850000;267;NoDriverID

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 79 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

7-21. Release Output Control by Driver ID

● Definition : Request all registered driver IDs

Field Definitions Unit Remark

CMD_ID “ReleaseDIDOutControl” Release output control by driver ID temporarily
<example>
[command] ST300CMD;;02;ReleaseDIDOutControl
[response]ST300CMD;Res;100850000;267;ReleaseDIDOutControl

<note>
When the device activates related output because registered I-button is not inserted and the device receives
this command, the device deactivates related output temporarily until next parking.

7-22. Start DPA Calibration

This command is for starting DPA calibration.

Field Mark Value Meaning

CMD_ID “StartDPACAL”
<Example>
[command] ST300CMD;100850000;02;StartDPACAL
[response] ST300CMD;Res;100850000;010;StartDPACAL

<note>

7-23. Stop DPA Calibration

This command is for stopping DPA calibration.

Field Mark Value Meaning

CMD_ID “StopDPACAL”
<Example>
[command] ST300CMD;100850000;02;StopDPACAL
[response] ST300CMD;Res;100850000;010;StopDPACAL

<note>

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 80 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

7-24. Testing Output 1 for 30 seconds.

This table shows you how to test the output (i.e. Output1) for 30 seconds.

Field Mark Value Meaning

CMD_ID “ReqShortTest” Request the device to activate output to do testing for 30
seconds.
<example>
[command] ST300CMD;100850000;02;ReqShortTest
[response] ST300CMD;Res;100850000;259;ReqShortTest

Output 1 will be activated for 30 seconds for test. After 30 seconds, output 1 will be deactivated.

7-25. Testing Output 1 for 60 seconds.

This table shows you how to test the output (i.e. Output1) for 60 seconds.

Field Mark Value Meaning

CMD_ID “ReqTest” Request the device to activate output to do testing for 60
seconds.
<example>
[command] ST300CMD;100850000;02;ReqTest
[response] ST300CMD;Res;100850000;259;ReqtTest

Output 1 will be activated for 60 seconds for test. After 60 seconds, output 1 will be deactivated.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 81 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

8. Detailed Description on Event Lines and Features

8-1. Total 8 pin Event Lines

8-1-1. Immobilizer

If Output type is set to ‘Immobilizer’ or ‘Immobilizer & Auto Active’ and you connect this line to immobilize the
vehicle, the Output line can use the immobilizer.

When the device recognizes the command to activate the immobilizer output, one of the 2 options (‘Active’ or
‘Inactive’) will be selected. Which activation you choose will depend on what mode the vehicle is in a parking mode
or in a driving mode.

In case of driving, the immobilizer activation is made in a way of progressive blocking as shown the following
blinking diagram:

The active time of the immobilizer is increased by 90ms each 4s. Three (3) minutes later, the immobilizer starts
being activated and will be activated continuously.

However, in case of parking as soon as the vehicle is parked, the immobilizer is activated normally.

In a case that the Output type is set to ‘Immobilizer & Auto active’, the output is activated automatically as long as
the vehicle is parked. In such a case the Output is also activated as long as the vehicle starts being in a driving
mode.

If the device receives a command to activate the immobilizer output, the output is always activated regardless to a
mode type (either parking mode or driving mode).

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 82 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

8-1-2. Immobilizer2

If output type is set to ‘Immobilizer2’(or ‘Immobilizer2 & Auto Active’), the way how ‘Immobilizer2’(or ‘Immobilizer2 &
Auto Active’) functions is same as the way how ‘9-1-1. Immobilizer’ functions.

The active time of the ‘Immobilizer2’(or ‘Immobilizer2 & Auto Active’) is increased by 90ms every 2.5 seconds.

One(1) minute later, the immobilizer starts being activated and will be activated continuously.

<NOTE> When you use the IMMOBILIZER please check the following conditions.

The combination of the order to use the IMMOBILIZER with the OUTPUTx

Connect the power of the

If not connected to the
Device to constant power
constant power of the vehicle,
of the vehicle
OUTPUT OUTPUT ACIVE OUTPUT ACIVE
OUTPUTx Type
LINE 0 1 0 1

Immobilizer,
1 /2 O O O X
Immobilizer Auto,
Immobilizer 2, 3/4
Immobilizer Auto 2
O X O X
(If available)
O : Available , X : Not available / OUTPUT ACTIVE : 0(OPEN) , 1(GND)

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 83 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

8-1-3. Alert of Buzzer

In a case that the Output type is set to ‘Buzzer’, the buzzer alerts. The following table shows such cases:

8-1-2-1. Related with over-speed

Condition Alert Pulse Meaning
Over-speed When vehicle’s speed
(Out = Buzzer) exceeds the over-speed
value.
Over-speed When vehicle’s speed
(Out = exceeds the over-peed
NRT_Buzzer) value.

Stop buzzer When the vehicle’s speed

is maintained under (over-
speed value – 5km/h) for
10 seconds.

8-1-2-2. Related with Anti-theft

In case one of any input ports is set to “Anti-Theft”.
Condition Alert Pulse Meaning
Enable This size of Alert pulse is
generated ifyou enable this
function by pressing the
anti-theft button for 10
seconds.
Disable This type of Alert pulse is
generated ifyou disable
this functionby pressing
anti-theft button for 10
seconds.
Lock Alert When it starts to be in a
locking mode. (anti-theft
function is enabled and 20
seconds later after
beginning to park vehicle.
Emergency

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 84 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

8-2. Indication with Two (2) LEDs

Blue LED indicates GPS status and red LED indicates GPRS status while the device is not processing call.

8-2-1. Red LED for GPS

GPS Blink Count Meaning

Normal 1

No Fix 2

<Probable Situations>

1. If power is on, GPS chipset tries to find position for some

minutes.
2. If device has weak connectivity with GPS network or if it has no
GPS signal position
3. If GPS connectivity with a device is weak
GPS Chipset Error 4
GPS Antenna Error
<Probable Situations>
1. If GPS antenna is disconnected.
2. If GPS antenna or socket of GPS antenna is broken.
3. If device is broken.

8-2-2. Blue LED for GPRS

GPRS Blink Count Meaning

Normal 1

Server Com. Error 2

< Probable Situations >

1. If the server or network parameter is wrong.
2. If the server is closed.
3. If there is a temporary network barrier
GPRS Com. Error 3

<Probable Situations >

1. If network parameter is wrong.
2. If SIM is blocked and it is impossible to use GPRS session
3. If there is a temporary network barrier
4. If device receives weak GPRS signal
5. If GPRS connectivity with a device is weak
No Network 4

< Probable Causes>

Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 85 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

1. If GPRS antenna is disconnected

2. If GPRS antenna or socket of GPRS antenna is broken
3. If the device is broken
SIM PIN Locked 5

<Probable Situation >

1. If SIM PIN is enabled.
Cannot Attach NW 6

< Probable Situations>

1. If device receives weak GPRS signal
2.If GPRS connectivity with a device is weak
No SIM 7

< Probable Situations >

1. If there is no SIM or if SIM is not inserted properly
2. If SIM or SIM socket is broken.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 86 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

8-3. Power Saving

The device can save power consumption of the battery by using one of two modes such as Sleep Mode, Deep
Sleep Mode. If PWR_DN is set with ‘1’ or ‘2’ and report interval in parking mode is made every 2 minutes or longer
than 2 minutes to enable the devices to process power down while the vehicle is in parking situation.

However, there are some restrictions in processing power down:

- If an emergency situation occurs, device cannot process power down for 30 minutes due to safety issue.
- When GPS signal is not fixed or weak, the device can start to process power down after trying to fix for
maximum 20 minutes.
- If communication with the server fails continuously, the device processes Deep Sleep after trying to make
communications for 8 minutes.
- While the device is charging the backup battery, it cannot process Deep Sleep.

Device turns off LED and sends a status report and a related alert before entering the power-down functionality.

The device terminates power down either when ignition is ON or when an event or an emergency occurs. In such
cases, the device sends related alert and status string, instead.

- Sleep

Device turns off only GPS part and GPRS part enters Sleep. Even for time of Sleep, all communication with the
server works normally and the device can receive SMS or call always. Average of Sleep current is lower than 10mA
and this current may be increased under weak GPRS condition.

- Deep Sleep

Device turns off GPS and GPRS part. For time of Sleep, all communication with the server is impossible and it
cannot receive any SMS messages or any calls, either. Device turns on GPRS session every max. 30 minutes.
However, the device can receive SMS or call while it is in Deep Sleep. Average current during Deep Sleep mode is
around 5mA (non-battery version).

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 87 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

8-4. Backup Battery

The device has a back-up battery in order to be prepared for any emergency cases when the main power source is
removed or sabotaged. When the vehicle is stolen and power of device is removed, the back-up battery starts
working as a replacement power source for the main power source (the vehicle’s battery).

Back-up battery at full charge on good GPRS network condition at a reporting interval value of every 3 minutes, the
device can work for 6 hours at least.

The device was designed to keep back-up battery staying as effective as possible all the time. Charging the back-
up battery starts if voltage of the back-up battery goes below 4,2V.In a parking mode, charging the back-up battery
is hold when the main power source gets consumed down to 90% of the normal voltage level.

The charging algorithm for the back-up battery has a protection against over-voltage, abnormal charging current
and high temperature.

In addition, the device alerts about battery error if the back-up battery cannot be charged.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 88 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

8-5. Motion Sensor

<About How to activate Motion Sensor>

- Ignition ON (Driving)

The sensor mode goes to collision detection mode. So, if the vehicle has a car accident, the accident may bring
about a big impact of which value is higher than that of the specified collision threshold (COLL_THRES). In this
case the device will be reporting a collision message to the server.

After a collision is made against the vehicle, the sensor will be disabled for a while (30 seconds) so as to avoid
sending to the server the same message as the first one repeatedly.

- Ignition OFF (Parking)

‘Ignition Off” situation means that the vehicle is in state of parking and that the sensor goes to ‘parking mode’
(shock or movement detection mode).

In this situation, if there is a shock made on the vehicle by somebody, the device will report a shock message to the
server. The device will also exit from the power down mode if the device has been in power down mode.

In case of movement, the device will exit from the mode of power down to check functionality of ‘Parking Lock’ from
the power down mode without reporting to the server.

After triggering an event such as a shock or a movement, the sensor will be disabled for a while (for 30 seconds)
so as to avoid sending to the server the same message as the first one repeatedly.

<About Threshold>

- Collision Threshold

Our recommendation is 0.7 but it is only for reference value obtained from our field testing made on real vehicles
(nearby gear).The value may vary in a real situation depending upon driving manner or condition of road. So, you
need to check this value.

- Shock Threshold

Our recommendation is 0.04 but it is only for reference value obtained from our field testing made on real vehicles
(nearby gear).Motion sensor is installed on an inside part of the vehicle’s body to measure sensitivity value(s)
created by vibration and shock impact given to the vehicle. Value of this sensitivity varies because it depends on
what body part of the vehicle the motion sensor is installed.

Shock Threshold is also used for checking movement of vehicle. So, the device may not be able to recognize if a
shock threshold value is too high. You need to consider these kinds of factors measurable under realistic
environment when you also adjust the values.

State Detection Exit from Power down Reporting about:

Motion Shock Collision Motion Shock Collision Motion Shock Collision
Parking ON Enable X Exit Exit Exit X Enable X
Driving OFF OFF Enable X X X X X Enable
Suntech International Ltd. Confidential Document
 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 89 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

<Note>:
 ON : activation
 OFF : Deactivation
 Enable : Enable or Disable by setting
 X: Please, do not care.

For setting method, please refer “Motion Sensor Parameter Settings” chapter.

[Caution] :Basically, the device checks any motions in parking mode(Ignition Off). It does not care about the enable
flags such as COLL_EN or SHOCK_EN. This means that, if the device senses any motion (movement) created in
the power down mode, it will exit from the power down mode as if a creature would wake up from sleeping
suddenly. So, if you want to check the power down mode to save power consumption of the backup battery, DO
NOT give any impacts to the vehicle.

8-6. Protection of Vehicle Battery

For a period of duration that the vehicle has been in a parking mode for a long time by consuming vehicle’s battery
down to a very low level, the device starts entering the Deep Sleep Mode automatically. This situation happens
because the device intends to prevent vehicle’s battery from wasting power. In this case, the device alerts with
ALERT_ID 14 before entering the deep sleep mode, and exits from the deep sleep mode either when ignition line
goes to ‘ON ‘or until the voltage level is increased sufficiently.

The vehicle’s battery level for protection can be changed by making a Command,‘$SetMVolt’.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 90 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

8-7. Anti-Theft

Anti-theft function available at the device is used to protect the vehicle from a risk of potential thefts by utilizing
buzzer, immobilizer and alerting to the server.

In order to use the function related with the anti-theft, the following basic conditions should be satisfied:

[Basic Conditions]

1. IGNITION of event parameter should not be set to “0” (No Use).

2. One input should be set to “Anti-theft” type.

If one output event is set to immobilizer or buzzer, immobilizer or buzzer can be activated automatically when
emergency related with anti-theft occurs.

Activation/Deactivation

When the input is set to “Anti-theft” by command, anti-theft is enabled by default at first.
Activation/deactivation state of anti-theft can be checked by “PresetA” command.

Case of ‘Anti-Theft’

In a case that anti-theft button type is “Anti-theft “and that the device has a buzzer, the anti-theft function can be
activated or deactivated by pressing anti-theft button for more than 10seconds.
If anti-theft button is pressed for 10 seconds in activation mode of anti-theft, anti-theft gets disabled by making the
buzzer beep two times.

On the other hand, if anti-theft button is pressed as being disabled, anti-theft gets enabled by making the buzzer
beep just one time.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 91 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

Anti-theft without Door Sensor

The anti-theft system in a vehicle without door sensor can be operated. The followings show you how it works:

1. About when the anti-theft system starts working?  There are 2 different types of the start timing of the anti-
theft function as described below:

If your device has been configured with the “Anti-theft Button”, twenty (20) seconds later after the vehicle is
parked (ignition goes to off), the protection function starts working by making a beep just one time.

2. After driving is started (ignition goes to on) in state of vehicle protection, the driver should press the anti-theft
button within the pre-defined time period of “Delay of Anti-theft Release” described in the “New Parameter.

3. If the button is pressed for 1 second within this time period, the protection function is released. If the driver has
not pressed the button within this time period, anti-theft emergency of the device starts working immediately.

4. In emergency, the buzzer and the immobilizer are activated if they are connected properly. After the preset
time of “Delay of Anti Theft Alert”, the device sends emergency report about anti-theft occurring.

5. However, you can stop such an emergency functioning of the device if you were not expecting such an
emergency. The followings are two (2) alternatives on how to stop functioning the Emergency:

 Alt. 1. By pressing anti-theft button for 1 second, the emergency situation can be stopped immediately.

 Alt. 2. As soon as all the immobilizer and the buzzer start getting deactivated by commands of the
“Disable Output”, the emergency situation will be over.

Anti-Theft with Door Sensor

The anti-theft system in a vehicle having door sensor can be operated. The followings show you how it works:

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 92 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

1. About when the anti-theft system starts working?  There are 2 different types of the start timing of the anti-
theft function as described below:

- Under an assumption that your device has been configured with the “Anti-theft Button”, twenty (20)
seconds later after the driver parks the vehicle (ignition goes to off), opens and closes the door, the
protection function starts working by making a beep just one time.

- Under an assumption that your device has been configured with the “Anti-theft Button2”, twenty (20)
seconds later after the driver parks the vehicle (ignition goes to off), opens and closes the door, the
protection function starts working silently.

2. After the door is opened and closed in state of vehicle protection, the driver should press the anti-theft button
within the pre-defined time period of “Delay of Anti-theft Release” described in the “New Parameter.

3. If the button is pressed for 1 second within this time period, the protection function is released. If the driver has
not pressed the button within this time period, anti-theft emergency of the device starts working immediately.

4. In emergency, the buzzer and the immobilizer are activated if they are connected properly. After the preset
time of “Delay of Anti Theft Alert”, the device sends emergency report about anti-theft occurring.

5. However, you can stop such an emergency functioning of the device if you were not expecting such an
emergency. The followings are two (2) alternatives on how to stop functioning the Emergency:

 Alt. 1. By pressing anti-theft button for 1 second, the emergency situation can be stopped immediately.

 Alt. 2. As soon as all the immobilizer and the buzzer start getting deactivated by commands of the
“Disable Output”, the emergency situation will be over.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 93 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

8-8. Storage of Reports un-sent

Device has maximum storage capacity of the un-sent reports in such cases as follows:

 2,000 status reports (**),

 50 emergency reports,

 50 alert reports (including event reports), and

 1500 bytes for the response that the command has required the device to respond with as command
response

Note (**):

Due to bad report-routing environment, device could not make a real-time based reporting. For example,
the reporting router does neither run properly, is nor connected properly. In such a situation there might be
a report which has consequently failed to arrive in the server successfully after making several attempts to
send the report to the server. In that case, the device stores such a report for a while until such
environment (e.g. GPRS network) gets back to normal to enable the device to try to send the report to the
server again.

When ‘status reports’ start being accumulated, max 1000 reports can be hold in the buffer storage of the
device. If those ‘status reports’ are triggered out to the server, the oldest report is erased first and a new
report is buffered if the buffer is completely full of those reports. And then, a new status report enters
(FIFO: First In First Out as a sequential system).

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 94 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

8-9. I-button

ST340UR supports reading I-button that has unique ID, 14 hex digits.
The device uses I-button’s ID as driver ID and can permit or reject driving depending on registration of the inserted
ID.

Driver ID can be registered up to 5000 in one device. There are 2 methods for registration. One is by command,
the other is by master I-button.
Below is flow of registration by master I-button.
1. Master I-button (add master / remove master) was inserted and removed.
2. New I-button is inserted within 10 seconds after remove.
3. And, the ID of I-button is registered or deregistered automatically.

Once the device recognizes-button, this ID of the button is valid until the vehicle changes from driving to parking
although the I-button is removes. So, until the next parking, the device reports with this ID information and approval
of this ID from registration table forbids activation by driver ID.

Let’s take two examples.

Case 1)
1. When registered I-button is inserted in parking, the buzzer beeps once (if buzzer is connected) and the
device sends alert (ID=59).
2. I-button is removed and the device sends alert (ID=60).
3. Device reports with previous I-button’s ID yet.
4. The vehicle turns to driving, but Output is not activated although registered I-button is not inserting because
previous I-button’s ID is valid.
5. When the vehicle goes to parking, ID is removed.
Case 2)
1. When unregistered I-button is inserted in parking, the buzzer beeps once (if buzzer is connected) and the
device sends alert (ID=59).
2. The vehicle turns to driving, and the device activates related output because previous driver ID is not in
registration table.
3. The vehicle turns to parking, and the device release related output.
4. When the I-button is removed, device sends alert (ID=60) and the ID field in report is removed.

8-10. Driver Pattern Calibration

This is the steps to calibrate Driver Pattern.

1. Turn ON and turn OFF ignition line (blue line) 7 times continuously.
st nd rd th th th th
On(1 )  Off(2 )  ON(3 )  Off(4 )  ON(5 )  Off(6 )  On(7 )
2. Wait during 5 seconds.
3. And GPRS LED (blue) and GPS LED (red) blink 0.5s continuously.
4. Driver in normal conditions more than 10 Km/h. The device needs to identify more than 3 braking,
acceleration and curve for auto calibration.
5. After driving turn off and turn on the ignition. The device will blinks the LED with normal conditions.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 95 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

8-11. Over-speed

There are 3 types of over-speed for ST300 SB retails. Over-speed, over-speed under rain and over-speed in
circle geo-fence.
Over-speed has no configurable time for chattering (fixed as 10 seconds), but over-speed under rain and
over-speed in circle geo-fence have the configurable time.

All of over-speed can be checked when the speed of vehicle is more than related speed-limit rightly.
And then, return from over-speed can be checked when the speed of vehicle is less than tolerance speed as
below.
1) If speed-limit is more than 100km/h, tolerance speed is equal "speed-limit - 5km/h".
2) If speed-limit is from 50km/h to 100km/h, tolerance speed is equal "speed-limit - 3km/h".
3) If speed-limit is less than 50km/h, tolerance speed is equal "speed-limit - 2km/h".
In case of over-speed, the device activates a buzzer rightly when over-speed is checked, and then sends an
alert after 10 seconds.
In case of over-speed under rain or over-speed in a circle geo-fence, the device activates a buzzer rightly
when over-speed is checked, but send an alert after waiting related delay under over-speed condition.
And.. The device sends an alert and deactivates a buzzer rightly when return from over-speed is checked.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 96 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

9. Engineering Command

9-1. Command on how to shutdown back-up battery

The ‘Shutdown command’ is mainly used to save power consumption of the back-up battery which has not been
installed completely on a vehicle. This command is available only for a device model that has a back-up battery.

This command should be sent only via RS232; not via ‘SyncTrak’.

Command $SHTDN<enter>
Response OK (successful)
NO SIM (Error: No SIM is inserted.)
ERROR: Plug out the Main Power! (Error: The Main power is connected).
<Note>

In order to send this command, the following three steps should be taken to:

1. Insert SIM and connect the main power (12V or 24V) and the battery.
2. Disconnect the main power.
3. Send “$SHTDN” command 3 seconds later.

After entering the storage mode, the device cannot be operated until the main power is connected.

A battery with 96ecogni. 30% of charging level can last for 2 months in Shutdown Mode.

9-2. Command on how to stop shutdown back-up battery

This command is used when a tracking system programmer wants to stop processing the 3 steps described above.
This command should be sent only via RS232; not via ‘SyncTrak’.

Command $SHTRST<enter>
Response OK
<Note>

This command can be recognized only for the time that the device does not complete steps for entering storage
mode yet.

Suntech International Ltd. Confidential Document

 Doc. Title Author Page of Pages

ST340UR OPERATION MANUAL SA KIM 97 of 97

Concerning Doc. No. Rev. Date

Features and How to set parameters 1.03 2019/10/18

Revisions
Rev. Date Modifications were made on: Author
Rev. 1.00 2019-04-14 Construct Protocol. Based on ST340UR SA Kim
Rev. 1.01 2019-05-23 Fixed some wrong explanations SA Kim
Rev. 1.02 2019-09-20 Changed power down specification related on GPS SA Kim

- End of the Document -

Suntech International Ltd. Confidential Document