V20.1.

NETUM C750 Manual

Contents
Firmware Version ....................................................................................................................................... - 1 -
Barcode Programming ............................................................................................................................... - 1 -
Connection Way ......................................................................................................................................... - 1 -
Working via USB Cable ....................................................................................................................... - 1 -
Working via 2.4G receiver .................................................................................................................. - 1 -
Working via Bluetooth ....................................................................................................................... - 1 -
Connection Modes: .................................................................................................................................... - 2 -
Wired Connection .............................................................................................................................. - 2 -
USB HID-KBW ............................................................................................................................. - 2 -
USB COM Port Emulation........................................................................................................... - 2 -
RF Wireless Connection. .................................................................................................................... - 2 -
*RF DONGLE HID-KBW ............................................................................................................... - 2 -
RF DONGLE AS VIRTUAL COM .................................................................................................... - 2 -
Bluetooth Connection ........................................................................................................................ - 3 -
Basic Mode (HID) (default)......................................................................................................... - 3 -
How to pair bluetooth under Basic Mode (HID) ? .................................................................... - 3 -
Bluetooth keyboard Upload Speed ........................................................................................... - 3 -
BLE Mode ................................................................................................................................... - 4 -
SPP Mode ................................................................................................................................... - 4 -
Scanning Mode: ......................................................................................................................................... - 5 -
*Trigger Mode (Default) .................................................................................................................... - 5 -
Auto Sense Mode ............................................................................................................................... - 5 -
Continuous Mode .............................................................................................................................. - 5 -
Keyboard Language .................................................................................................................................... - 5 -
DATA UPLOADING MODE .......................................................................................................................... - 7 -
Quit Offline Mode .............................................................................................................................. - 7 -
Offline Mode ...................................................................................................................................... - 7 -
Output Stored Data ............................................................................................................................ - 8 -
Output Total Entry ............................................................................................................................. - 8 -
Clear Memory .................................................................................................................................... - 8 -
Get Battery Volume ................................................................................................................................... - 8 -
Idle time ..................................................................................................................................................... - 8 -
Convert Case .............................................................................................................................................. - 9 -
Terminator ................................................................................................................................................. - 9 -
IOS Keyboard POP UP/HIDE ..................................................................................................................... - 10 -
Beeper ...................................................................................................................................................... - 10 -
Restore factory default ............................................................................................................................ - 10 -
Transmit Code ID Character ..................................................................................................................... - 11 -
Symbol Code ID Identifiers............................................................................................................... - 11 -
AIM Code Identifiers ........................................................................................................................ - 12 -
All Symbologies ........................................................................................................................................ - 12 -
1D Symbologies ................................................................................................................................ - 12 -
2D Symbologies ................................................................................................................................ - 13 -
1D Inverse Barcode ......................................................................................................................... - 13 -
Decode UPC/EAN Supplementals UPC/EAN .................................................................................... - 14 -
UPC-A ............................................................................................................................................... - 14 -
Enable/Disable UPC-A .............................................................................................................. - 14 -
Transmit Preamble Character .................................................................................................. - 15 -
UPC-A Transmit Check Character ............................................................................................. - 15 -

1
 UPC-A Add-On Code................................................................................................................. - 15 -
UPC-A Add-On Code Required ................................................................................................. - 16 -
UPC-E................................................................................................................................................ - 16 -
Enable/Disable UPC-E .............................................................................................................. - 16 -
Transmit Preamble Character .................................................................................................. - 17 -
UPC-E Transmit Check Character ............................................................................................. - 17 -
Convert UPC-E to UPC-A .......................................................................................................... - 17 -
UPC-E Add-On Code ................................................................................................................. - 17 -
UPC-E Add-On Code Required ................................................................................................. - 18 -
EAN-8 ............................................................................................................................................... - 18 -
Enable/Disable EAN-8 .............................................................................................................. - 18 -
EAN-8 Extension ....................................................................................................................... - 19 -
EAN-8 Add-On Code ................................................................................................................. - 19 -
EAN-8 Add-On Code Required ................................................................................................. - 19 -
EAN-8 Transmit Check Character ............................................................................................. - 20 -
EAN-13 ............................................................................................................................................. - 20 -
Enable/Disable EAN-13 ............................................................................................................ - 20 -
EAN-13 Add-On Code ............................................................................................................... - 20 -
EAN-13 Add-On Code Required ............................................................................................... - 21 -
EAN-13 Transmit Check Character ........................................................................................... - 21 -
Bookland EAN(ISBN)......................................................................................................................... - 21 -
Enable/Disable EAN(ISBN) ....................................................................................................... - 21 -
Bookland ISBN .................................................................................................................................. - 22 -
Enable/Disable ISBN................................................................................................................. - 22 -
Code 128 .......................................................................................................................................... - 22 -
Enable/Disable Code 128 ......................................................................................................... - 22 -
Code128 Transmit Check Character......................................................................................... - 23 -
GS1-128 (UCC/EAN-128) .................................................................................................................. - 23 -
Enable/Disable GS1-128 (UCC/EAN-128) ................................................................................. - 23 -
GS1-128 Transmit Check Character ......................................................................................... - 23 -
ISBT 128............................................................................................................................................ - 23 -
Enable/Disable ISBT 128 .......................................................................................................... - 23 -
Code39 ............................................................................................................................................. - 24 -
Enable/Disable Code 39 ........................................................................................................... - 24 -
Set Length Range for Code39................................................................................................... - 24 -
One Discrete Length................................................................................................................ - 24 -
Two Discrete Lengths .............................................................................................................. - 25 -
Length Within Range............................................................................................................... - 25 -
Any Length .............................................................................................................................. - 25 -
Code 39 Check Digit Verification.............................................................................................. - 25 -
Transmit Code 39 Check Digit .................................................................................................. - 26 -
Enable/Disable Code 39 Full ASCII ........................................................................................... - 26 -
Code39 Transmit Start/Stop Character.................................................................................... - 27 -
Code 32 ............................................................................................................................................ - 27 -
Enable/Disable Code 32 ........................................................................................................... - 27 -
Code 32 Prefix .......................................................................................................................... - 27 -
Code 93 ............................................................................................................................................ - 27 -
Enable/Disable Code 93 ........................................................................................................... - 27 -
Set Lengths for Code93 ............................................................................................................ - 28 -
One Discrete Length................................................................................................................ - 28 -
Two Discrete Lengths .............................................................................................................. - 28 -
Length Within Range............................................................................................................... - 29 -
Any Length .............................................................................................................................. - 29 -
Code 93 Check Digit Verification.............................................................................................. - 29 -
Transmit Code 93 Check Digit .................................................................................................. - 29 -
Code 11 ............................................................................................................................................ - 30 -
Enable/Disable Code 11 ........................................................................................................... - 30 -
Set Lengths for Code 11 ........................................................................................................... - 30 -

2
 One Discrete Length................................................................................................................ - 30 -
Two Discrete Lengths .............................................................................................................. - 31 -
Length Within Range............................................................................................................... - 31 -
Any Length .............................................................................................................................. - 31 -
Code 11 Check Digit Verification.............................................................................................. - 31 -
Transmit Code 11 Check Digits ................................................................................................ - 32 -
Interleaved 2 of 5/ITF....................................................................................................................... - 32 -
Enable/Disable Interleaved 2 of 5 ............................................................................................ - 32 -
Set Lengths for Interleaved 2 of 5 ............................................................................................ - 33 -
One Discrete Length................................................................................................................ - 33 -
Two Discrete Lengths .............................................................................................................. - 33 -
Length Within Range............................................................................................................... - 33 -
Any Length .............................................................................................................................. - 34 -
I 2 of 5 Check Digit Verification ................................................................................................ - 34 -
Transmit I 2 of 5 Check Digit .................................................................................................... - 34 -
ITF14................................................................................................................................................. - 35 -
Enable/Disable ITF14 ............................................................................................................... - 35 -
Transmit ITF14 Check Digit ...................................................................................................... - 35 -
Discrete 2 of 5/Industrial 2 of 5/IND25............................................................................................ - 35 -
Enable/Disable Discrete 2 of 5 ................................................................................................. - 35 -
Set Lengths for Discrete 2 of 5 ................................................................................................. - 36 -
One Discrete Length................................................................................................................ - 36 -
Two Discrete Lengths .............................................................................................................. - 36 -
Length Within Range............................................................................................................... - 36 -
Any Length .............................................................................................................................. - 37 -
Discrete 2 of 5 Check Digit Verification ................................................................................... - 37 -
Transmit Discrete 2 of 5 Check Digit ........................................................................................ - 37 -
Matrix 25 .......................................................................................................................................... - 38 -
Enable/Disable Matrix 25......................................................................................................... - 38 -
Matrix 25 Check Digit Verification .......................................................................................... - 38 -
Transmit Matrix 25 Check Digit ............................................................................................... - 38 -
Set Lengths for Matrix 25 ......................................................................................................... - 39 -
One Discrete Length................................................................................................................ - 39 -
Two Discrete Lengths .............................................................................................................. - 39 -
Length Within Range............................................................................................................... - 40 -
Any Length .............................................................................................................................. - 40 -
Standard 25/IATA 25 ........................................................................................................................ - 40 -
Enable/Disable Standard 25 ..................................................................................................... - 40 -
Standard 25 Check Digit Verification ....................................................................................... - 41 -
Standard 25 Transmit Check Character ................................................................................... - 41 -
Set Lengths for Standard 25 ..................................................................................................... - 41 -
One Discrete Length................................................................................................................ - 42 -
Two Discrete Lengths .............................................................................................................. - 42 -
Length Within Range............................................................................................................... - 42 -
Any Length .............................................................................................................................. - 42 -
Codabar ............................................................................................................................................ - 43 -
Enable/Disable Codabar........................................................................................................... - 43 -
Set Lengths for Codabar ........................................................................................................... - 43 -
One Discrete Length................................................................................................................ - 43 -
Two Discrete Lengths .............................................................................................................. - 43 -
Length Within Range............................................................................................................... - 44 -
Any Length .............................................................................................................................. - 44 -
Codabar Check Digit Verification ............................................................................................. - 44 -
Codabar Transmit Check Character ......................................................................................... - 44 -
Start/Stop Character Format ................................................................................................... - 45 -
MSI ................................................................................................................................................... - 45 -
Enable/Disable MSI .................................................................................................................. - 45 -
Set Lengths for MSI .................................................................................................................. - 45 -
One Discrete Length................................................................................................................ - 46 -

3
 Two Discrete Lengths .............................................................................................................. - 46 -
Length Within Range............................................................................................................... - 46 -
Any Length .............................................................................................................................. - 46 -
MSI Check Character Verification ............................................................................................ - 47 -
GS1 DataBar/RSS .............................................................................................................................. - 47 -
Enable/Disable GS1 DataBar-14............................................................................................... - 47 -
Enable/Disable GS1 DataBar Limited ....................................................................................... - 47 -
Enable/Disable GS1 DataBar Expanded ................................................................................... - 48 -
PDF417 ............................................................................................................................................. - 48 -
Enable/Disable PDF417 ............................................................................................................ - 48 -
PDF 417 Twin Code .................................................................................................................. - 49 -
Read Normal Phase/ Phase Reversal ....................................................................................... - 49 -
QR..................................................................................................................................................... - 50 -
Enable/Disable QR ................................................................................................................... - 50 -
QR Twin Code ........................................................................................................................... - 50 -
Enable/Disable QR ECI Output ................................................................................................. - 51 -
Read Normal Phase/ Phase Reversal ....................................................................................... - 51 -
Data Matrix(DM) .............................................................................................................................. - 51 -
Enable/Disable Data Matrix(DM) ............................................................................................. - 51 -
Data Matrix Twin Code ............................................................................................................ - 52 -
Enable/Disable Data Matrix ECI Output................................................................................... - 52 -
Read Normal Phase/ Phase Reversal ....................................................................................... - 53 -
Maxi Code ........................................................................................................................................ - 53 -
Enable/Disable Maxi Code ....................................................................................................... - 53 -
Aztec Code ....................................................................................................................................... - 53 -
Enable/Disable Aztec Code ...................................................................................................... - 54 -
Han Xin Code .................................................................................................................................... - 54 -
Enable/Disable Han Xin Code................................................................................................... - 54 -
Han Xin Twin Code ................................................................................................................... - 54 -
Read Normal Phase/ Phase Reversal ....................................................................................... - 55 -
Plessey.............................................................................................................................................. - 55 -
Enable/Disable Plessey ............................................................................................................ - 55 -
Check Character Verification ................................................................................................... - 56 -
Transmit Check Character ........................................................................................................ - 56 -
Brazil Bank Code .............................................................................................................................. - 56 -
Enable/Disable Brazil Bank Code ............................................................................................. - 56 -
COMPOSITE ...................................................................................................................................... - 56 -
Enable/Disable COMPOSITE ..................................................................................................... - 56 -
EAN/UCC .......................................................................................................................................... - 57 -
Enable/Disable EAN/UCC ......................................................................................................... - 57 -
Appendix 1: Numeric Bar Codes .............................................................................................................. - 57 -
Cancel Barcode ................................................................................................................................ - 59 -
Hide Prefix or suffix digits ........................................................................................................................ - 59 -
Output Format ................................................................................................................................. - 59 -
To Hide chars of barcode Start/Middle/End: ................................................................................... - 60 -
Numeric Bar Codes .......................................................................................................................... - 61 -
Output Format ................................................................................................................................. - 62 -
Table 1. ASCII Character Equivalents ....................................................................................................... - 65 -

4
5
SCANNER SETUP GUIDE

Firmware Version
Read below command barcode to check scanner firmware version.

Firmware Version
Barcode Programming
Netum barcode scanners are factory programmed for the most common terminal and communications
settings. If you need to change these settings, programming is accomplished by scanning the bar codes in this
guide. An asterisk (*) next to an option indicates the default setting.

Important Notes: Many of the command barcodes only work with a scanner in a particular connection modes.
Bluetooth or 2.4Ghz wireless mode as indicated by the header row of each table.

Connection Way

Working via USB Cable

Get Started:
①Connect scanner with your device via USB cable.
②If you use US keyboard, it's plug and play. If you use other type of keyboard , please refer to "keyboard
language" to configure the keyboard language before you use it.
③Locate the cursor on the place where you want the data to be displayed then you can start to scan.

Working via 2.4G receiver

Get Started:
①Scan command barcode of "RF 2.4Ghz Wireless Transmit".
②Plug the USB receiver on your computer.
③If you use US keyboard, it's plug and play. If you use other type of keyboard , please refer to "keyboard
language" to configure the keyboard language before use it.
④Locate the cursor on the place where you want the data to be displayed then you can start to scan.

*RF 2.4Ghz Wireless Transmit

Working via Bluetooth
Get Started:
①Scan command barcode of" Working via Bluetooth"

-1-
②Pair the bluetooth. Please refer to the “bluetooth pairing” Page 3.
④Set keyboard language. US Keyboard by default if you use other types of keyboard please configure
keyboard language before you use it.
⑤ Locate cursor on the place where you want the data to be displayed then you can start to scan.

Working via Bluetooth

Connection Modes:

Wired Connection
USB HID-KBW
By default, the scanner is in HID mode as a Keyboard device. It works on a Plug and Play basis and no driver is
required

*USB Cable as Keyboard (HID)

USB COM Port Emulation

If you connect the scanner to the Host via a USB connection, the USB COM Port Emulation feature allows the
host to receive data in the way as a serial port does.

USB Cable as Virtual COM

Note: Wire and Wireless connect way selected automatically, the Wire way has high priority.

RF Wireless Connection.
*RF DONGLE HID-KBW
By default, the scanner is in HID mode as a Keyboard device. It works on a Plug and Play basis and no driver is
required

*RF Dongle as Keyboard(HID)

RF DONGLE AS VIRTUAL COM

If you plug the RF Dongle to the host, the USB COM Port Emulation feature allows the host to receive data in
the way as a serial port does.

RF Dongle as Virtual COM

-2-
Bluetooth Connection
Basic Mode (HID) (default)
Configures the scanner to Human Interface Device (HID) mode. The scanner will be discoverable as a
Keyboard to other Bluetooth devices.

*Basic Mode(HID)

Basic Mode Features:

·NO software installation required
·Connects to most devices
·Scanner interacts with host device like a keyboard

How to pair bluetooth under Basic Mode (HID) ?

Android: Connect Android Device in Basic Mode (HID)
1. Power on the scanner. The LED light will be flashing.
2. Touch Home | Menu | Settings | Wireless & Networks | Bluetooth settings
3. Make sure the device has Bluetooth “On”.
4. In the list of found devices, select “Netum Bluetooth”. Tap Pair.
5. The scanner will make one long beep after bluetooth paired and LED light will turn to solid blue (no
blinking).

Apple: Connect Apple iOS Device (HID)

1.Power on the scanner. Blue LED light will start to flash.
2.Start a Bluetooth device search.
IOS: Tap Settings | General| Bluetooth. Turn on. A Bluetooth device search will begin.
3. In the device list, tap on “Netum Bluetooth”. Tap Pair.
4. The scanner will make one beep once it’s connected and LED light will turnto solid blue (no blinking) and is
ready to scan.

Windows: Connect Windows PC(HID)

1.Power on the scanner. Make sure the scanner is discoverable (unpaired).
2. Use your computer’s Bluetooth Settings to connect to the scanner.
3. Open Devices and Printers and select “Add a device”.
4. In the device list, select “Netum Bluetooth”. Click Next.
5. Follow the remaining screens to complete the wizard.
6. The scanner will make one beep once it’s connected and LED light will turn to solid blue (no blinking) and is
ready to scan.

Bluetooth keyboard Upload Speed

High Speed

-3-
 Medium Speed

Low Speed

Important Note:
Default Idle Time: Scanner will power off automatically if device is not connected within 1min.

Un-Pair Bluetooth :
Below two steps to unpair the bluetooth from previous device completely.
1.Scan Un-pair Bluetooth HID , Scanner disconnected from current device and waits for other device to be
paired.
2.Remove or Ignore"Netum Bluetooth" from your previous device.

Un-Pair Bluetooth

BLE Mode
For Apple Devices (a software was required to work under this mode)

BLE Mode
SPP Mode
For Windows or Android (a software was required to work under this mode)

SPP Mode
Important Note:

If you want to shift from HID to SPP or BLE just scan the Corresponding command barcode.
If you want to shift from SPP or BLE to HID mode, please ignore (or delete) "Netum Bluetooth"→ turn off
bluetooth→ scan command barcode of HID→ Open the bluetooth → repair it.

-4-
Scanning Mode:
*Trigger Mode (Default)
Scanning this bar code will enable the scanner to enter manual trigger mode.

Trigger Mode

Auto Sense Mode

Scanning this bar code will enable the scanner to enter auto sense mode.

Auto Sense Mode

Continuous Mode
This mode enables the engine to scan/capture, decode and transmit over and over again.

Continuous Mode

Keyboard Language
For example If you use French Keyboard, scan command barcode of “French keyboard ”. If you use a US
keyboard you can ignore this step.

* America EN keyboard French keyboard

Germany keyboard Italy keyboard

-5-
 Portugal keyboard Spain keyboard

Turkey Q keyboard Turkey F keyboard

UK keyboard Czech keyboard

Hungary keyboard Belgium FR keyboard

Brazil PT keyboard Canadian FR keyboard

Croatia keyboard Slovak keyboard

Denmark keyboard Finland keyboard

-6-
 Latin-America ES keyboard Netherland keyboard

Norway keyboard Poland keyboard

Serbia keyboard Slovenia keyboard

Sweden keyboard Swiss DE keyboard

Data Uploading Mode

If you are heading for a working area which lies outside the Bluetooth signal range, you may activate scanner’s
store mode, following steps described below. Under this mode, all scanned data will be stored directly into
the buffer memory of the device. Furthermore, the data entries will be permanently saved in the buffer
memory prior to the manual upload into the working station, so that you may upload them when you are near
your working device.

Quit Offline Mode

By scanning the following barcode, the device leaves the offline mode, normal mode will be reinitialised.

*Quit Offline Mode

Offline Mode
By scanning the following barcode, the offline mode will be activated

Offline Mode

-7-
Output Stored Data
By scanning the following barcode, all data entries in the buffer memory can be manually uploaded after
reconnecting to the working station.

Output Stored Data

Output Total Entry

By scanning the following barcode, the gross quantity of the uploaded data entries will be summarised .

Output Total Entry

Clear Memory
By scanning the following barcode, all data in the buffer memory will be deleted.

Clear Memory

Get Battery Volume

Scan below command barcode to get battery rough volume

Battery Rough Volume

Idle time
Scanner will turn to sleep after idle/inactive for 1min
Scan "Disable module Idle time" before you doing any other setup from this section.

Power Off Disable Sleep Mode

30S 3Mins

-8-
 10Mins 30Min

Convert Case

* Disable Convert Case

Up Low Case Swap (A<->a)

All Upper Case (a->A)

All Lower Case (A->a)

Notes: Command barcodes from Working mode section are only applied for Bluetooth wireless mode,

Terminator
The scanner provides a shortcut for setting the terminating character suffix to CR or CRLF and enabling it by
scanning the appropriate barcode below.

None CR&LF *

CR TAB

-9-
IOS Keyboard POP UP/HIDE
During the scanning IOS keyboard can be hided or popped up by scanning below command barcode.

IOS Keyboard POP UP/HIDE

Beeper
Enable/Disable scanner to beep to indicate successful scan.

BEEP OFF

*High Volume

Middle Volume

Low Volume
Restore factory default
Scanning the following barcodes one by one to restore the scanner to factory defaults. (Four steps included)

1.

2.

- 10 -
3.

4.

Transmit Code ID Character

A code ID character identifies the code type of a scanned bar code. This can be useful when decoding more
than one code type. The code ID character is inserted between the prefix character (if selected) and the
decoded symbol.

Symbol Code ID Character Code ID

Aim Code ID Character AIM ID

*None
Symbol Code ID Identifiers

A= UPC-A, UPC-E, EAN-8, EAN-13 J= MSI, MSI/Plessey

B= Code 39, Code 32 K= GS1-DataBar, /UCC/EAN-128
C= Codabar L= Bookland EAN, Bookland EAN/ISBN
D= Code 128, ISBT 128 M= Trioptic Code 39
E= Code 93 N= Coupon Code
F= Interleaved 2 of 5 R= GS1 DataBar-14, GS1 DataBar Limited, GS1 DataBar Expanded, RSS
G= Discrete 2 of 5 S= SETUP128
H= CODE11

- 11 -
r= PDF417 x= Maxi Code
u= DataMatrix(DM) v= Veri Code
q= QR c= HanXin
a= Aztec Code

AIM Code Identifiers

Each AIM Code Identifier contains the three-character string ]cm where:
] = Flag Character
c =Code Character (see Table 4-4)
m= Modifier Character

Table 4-4

A Code 39, Code 39 Full ASCII, Code 32 S Discrete 2 of 5, IATA 2 of 5

C Code 128, ISBT 128, GS1-128, X Code 39 Trioptic, Bookland EAN, Han Xin
Coupon (Code 128 portion), Setup128
E UPC/EAN, Coupon (UPC portion) e GS1 DataBar
F Codabar L PDF417
G Code 93 d Data Matrix(DM)
H Code 11 Q QR
I Interleaved 2 of 5 z Aztec Code

All Symbologies

Enable/Disable All Symbologies

If the Disable All Symbologies feature is enabled, the scanner will not be able to read any non-programming
barcodes except the programming barcodes.

Disable All Symbologies

Enable All Symbologies

1D Symbologies
Enable/Disable1D Symbologies
If the Disable 1D Symbologies feature is enabled, the scanner will not be able to read any 1D barcodes.

- 12 -
 Disable 1D Symbologies

Enable 1D Symbologies

2D Symbologies
Enable/Disable 2D Symbologies
If the Disable 2D Symbologies feature is enabled, the scanner will not be able to read any 2D barcodes.

Disable 2D Symbologies

Enable 2D Symbologies

1D Inverse Barcode
Regular barcode: Dark image on a bright background.
Inverse barcode: Bright image on a dark background.

* Disable to read 1D reverse barcode

- 13 -
 Enabled to read 1D reverse barcode

Decode UPC/EAN Supplementals UPC/EAN

Supplementals are bar codes appended according to specific format conventions (e.g.UPC A+2, UPC E+2, EAN
13+2, EAN 13+5). The following options are available:

*Ignore UPC/EAN with Supplementals

Decode UPC/EAN with Supplementals

Auto discriminate UPC/EAN Supplementals

UPC-A
Enable/Disable UPC-A
To enable or disable UPC-A, scan the appropriate bar code below.

*Enable UPC-A

- 14 -
 Disable UPC-A

Transmit Preamble Character

Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-A
barcode. Select one of the following options for transmitting UPC-A preamble to the host device: transmit
system character only or transmit system character and country code (“0” for USA).

No System Character

System Character & Country Code * System Character

UPC-A Transmit Check Character

* Transmit UPC-A Check Character Do Not Transmit UPC-A Check Character

UPC-A Add-On Code

A UPC-A barcode can be augmented with a two-digit or five-digit add-on code to form a new one.

Enable 2-Digit Add-On Code/ Enable 5-Digit Add-On Code: The scanner decodes a mix of UPC-A
barcodes with and without 2-digit/5-digit add-on codes.
Disable 2-Digit Add-On Code/ Disable 5-Digit Add-On Code: The engine decodes UPC-A and ignores
the add-on code when presented with a UPC-A plus add-on barcode. It can also decode UPC-A barcodes
without add-on codes.

- 15 -
Enable 2-Digit Add-On Code *Disable 2-Digit Add-On Code

Enable 5-Digit Add-On Code * Disable 5-Digit Add-On Code

UPC-A Add-On Code Required

When UPC-A Add-On Code Required is selected, the scanner will only read UPC-A barcodes that contain add-
on codes.

UPC-A Add-On Code Required * UPC-A Add-On Code Not Required

UPC-E
Enable/Disable UPC-E
To enable or disable UPC-E, scan the appropriate bar code below.

*Enable UPC-E

Disable UPC-E

- 16 -
Transmit Preamble Character
Preamble characters (Country Code and System Character) can be transmitted as part of a UPC-E
barcode. Select one of the following options for transmitting UPC-E preamble to the host device: transmit
system character only or transmit system character and country code (“0” for USA).

No System Character

System Character & Country Code * System Character

UPC-E Transmit Check Character

* Transmit UPC-E Check Character Do Not Transmit UPC-E Check Character

Convert UPC-E to UPC-A

Convert UPC-E to UPC-A *Do not convert UPC-E to UPC-A

UPC-E Add-On Code

A UPC-E barcode can be augmented with a two-digit or five-digit add-on code to form a new one.

Enable 2-Digit Add-On Code/ Enable 5-Digit Add-On Code: The scanner decodes a mix of UPC-E
barcodes with and without 2-digit/5-digit add-on codes.
Disable 2-Digit Add-On Code/ Disable 5-Digit Add-On Code: The scanner decodes UPC-E and ignores
the add-on code when presented with a UPC-E plus add-on barcode. It can also decode UPC-E barcodes
without add-on codes.

- 17 -
 Enable 2-Digit Add-On Code *Disable 2-Digit Add-On Code

Enable 5-Digit Add-On Code * Disable 5-Digit Add-On Code

UPC-E Add-On Code Required

When UPC-E Add-On Code Required is selected, the scanner will only read UPC-E barcodes that contain add-
on codes.

UPC-E Add-On Code Required * UPC-E Add-On Code Not Required

EAN-8
Enable/Disable EAN-8
To enable or disable EAN-8, scan the appropriate bar code below.

*Enable EAN-8

Disable EAN-8

- 18 -
EAN-8 Extension

Disable EAN-8 Zero Extend: Transmit EAN-8 barcodes as is.

Enable EAN-8 Zero Extend: Add five leading zeros to decoded EAN-8 barcodes to extend to13 digits.

Enable EAN-8 Zero Extend *Disable EAN-8 Zero Extend

EAN-8 Add-On Code

A EAN-8 barcode can be augmented with a two-digit or five-digit add-on code to form a new one.

Enable 2-Digit Add-On Code/ Enable 5-Digit Add-On Code: The scanner decodes a mix of EAN-8
barcodes with and without 2-digit/5-digit add-on codes.
Disable 2-Digit Add-On Code/ Disable 5-Digit Add-On Code: The scanner decodes EAN-8 and ignores
the add-on code when presented with a EAN-8 plus add-on barcode. It can also decode EAN-8 barcodes
without add-on codes.

Enable 2-Digit Add-On Code *Disable 2-Digit Add-On Code

Enable 5-Digit Add-On Code *Disable 5-Digit Add-On Code

EAN-8 Add-On Code Required

When EAN-8 Add-On Code Required is selected, the scanner will only read EAN-8 barcodes that contain add-
on codes.

EAN-8 Add-On Code Required *EAN-8 Add-On Code Not Required

- 19 -
EAN-8 Transmit Check Character

* Transmit EAN-8 Check Character Do Not Transmit EAN-8 Check Character

EAN-13
Enable/Disable EAN-13
To enable or disable EAN-13, scan the appropriate bar code below.

*Enable EAN-13

Disable EAN-13

EAN-13 Add-On Code

A EAN-13 barcode can be augmented with a two-digit or five-digit add-on code to form a new one.

Enable 2-Digit Add-On Code/ Enable 5-Digit Add-On Code: The scanner decodes a mix of EAN-13
barcodes with and without 2-digit/5-digit add-on codes.
Disable 2-Digit Add-On Code/ Disable 5-Digit Add-On Code: The scanner decodes EAN-13 and ignores
the add-on code when presented with a EAN-13 plus add-on barcode. It can also decode EAN-13 barcodes
without add-on codes.

Enable 2-Digit Add-On Code *Disable 2-Digit Add-On Code

- 20 -
 Enable 5-Digit Add-On Code * Disable 5-Digit Add-On Code

EAN-13 Add-On Code Required

When EAN-13 Add-On Code Required is selected, the scanner will only read EAN-13 barcodes that contain
add-on codes.

EAN-13 Add-On Code Required *EAN-13 Add-On Code Not Required

EAN-13 Transmit Check Character

* Transmit EAN-13 Check Character Do Not Transmit EAN-13 Check Character

Bookland EAN(ISBN)
Enable/Disable EAN(ISBN)
To enable or disable EAN Bookland, scan the appropriate bar code below.

Enable Bookland EAN

- 21 -
 *Disable Bookland EAN

Bookland ISBN
Enable/Disable ISBN
To enable or disable Bookland ISBN, scan the appropriate bar code below.

*Bookland ISBN-10

Bookland ISBN-13

Code 128
Enable/Disable Code 128
To enable or disable Code 128, scan the appropriate bar code below.

*Enable Code 128

Disable Code 128

- 22 -
Code128 Transmit Check Character

Transmit Code128 Check Character * Do Not Transmit Code128 Check Character

GS1-128 (UCC/EAN-128)
Enable/Disable GS1-128 (UCC/EAN-128)

To enable or disable GS1-128, scan the appropriate bar code below.

*Enable GS1-128

Disable GS1-128

GS1-128 Transmit Check Character

Transmit GS1-128 Check Character * Do Not Transmit GS1-128 Check Character

ISBT 128
Enable/Disable ISBT 128

To enable or disable ISBT 128, scan the appropriate bar code below.

- 23 -
 *Enable ISBT 128

Disable ISBT 128

Code39
Enable/Disable Code 39
To enable or disable Code 39, scan the appropriate bar code below.

*Enable Code 39

Disable Code 39

Set Length Range for Code39

The length of a code refers to the number of characters (i.e., human readable characters), including check
digit(s) the code contains. Lengths for Code 39 may be set for any length, one or two discrete lengths, or
lengths within a specific range.

NOTE When setting lengths, single digit numbers must always be preceded by a leading zero.

One Discrete Length

This option limits decodes to only those Code 39 symbols containing a selected length. Lengths are selected
from the Numeric Bar Codes in appendix. For example, to decode only Code 39 symbols with 14 characters,
scan Code 39 - One Discrete Length, then scan 1 followed by 4. To change the selection or cancel an incorrect
entry, scan Cancel in appendix.

- 24 -
 Code 39 - One Discrete Length

Two Discrete Lengths

This option limits decodes to only those Code 39 symbols containing either of two selected lengths. Lengths
are selected from the Numeric Bar Codes in appendix. For example, to decode only those Code 39 symbols
containing either 2 or 14 characters, select Code 39 - Two Discrete Lengths, then scan 0, 2, 1, and then 4. To
change the selection or cancel an incorrect entry, scan Cancel in appendix.

Code 39 - Two Discrete Lengths

Length Within Range

This option limits decodes to only those Code 39 symbols within a specified range. For example, to decode
Code 39 symbols containing between 4 and 12 characters, first scan Code 39 - Length Within Range. Then
scan 0, 4, 1, and 2 according to Numeric Bar Codes in appendix. To change the selection or cancel an incorrect
entry, scan Cancel in appendix

Code 39 - Length Within Range

Any Length
Scan this option to decode Code 39 symbols containing any number of characters

Code 39 - Any Length

Code 39 Check Digit Verification

When this feature is enabled, the scan engine checks the integrity of all Code 39 symbols to verify that the
data complies with specified check digit algorithm. Only those Code 39 symbols which include a modulo 43
check digit are decoded. Only enable this feature if your Code 39 symbols contain a module 43 check digit.

- 25 -
 Verify Code 39 Check Digit

*Do Not Verify Code 39 Check Digit

Transmit Code 39 Check Digit

Scan this symbol to transmit the check digit with the data.

Transmit Code 39 Check Digit (Enable)

Scan this symbol to transmit data without the check digit.

*Do Not Transmit Code 39 Check Digit

Enable/Disable Code 39 Full ASCII

Code 39 Full ASCII is a variant of Code 39 which pairs characters to encode the full ASCII character set.

Enable Code 39 Full ASCII

- 26 -
 *Disable Code 39 Full ASCII

NOTE Trioptic Code 39 and Code 39 Full ASCII cannot be enabled simultaneously. If you get an error beep
when enabling Code 39 Full ASCII, disable Trioptic Code 39 and try again.

Code39 Transmit Start/Stop Character

Transmit Start/Stop Character ** Do not Transmit Start/Stop Character

Code 32
Enable/Disable Code 32

Code 32 is a variant of Code 39 used by the Italian pharmaceutical industry. Scan the appropriate bar
code below to enable or disable Code 32. Code 39 must be enabled and Code 39 check character
verification must be disabled for this parameter to function.

* Disable Code 32 Enable Code 32

Code 32 Prefix
Scan the appropriate bar code below to enable or disable adding the prefix character “A” to all Code 32
barcodes. Code 32 must be enabled for this parameter to function.

* Disable Code 32 Prefix Enable Code 32 Prefix

Code 93
Enable/Disable Code 93
To enable or disable Code 93, scan the appropriate bar code below.

- 27 -
 Enable Code 93

*Disable Code 93

Set Lengths for Code93

The length of a code refers to the number of characters (i.e., human readable characters), including check
digit(s) the code contains. Lengths for Code 93 may be set for any length, one or two discrete lengths, or
lengths within a specific range.

One Discrete Length

Select this option to decode only those codes containing a selected length. For example, select Code 93 One
Discrete Length, then scan 1, 4, to limit the decoding to only Code 93 symbols containing 14 characters.
Numeric Bar Codes is in appendix. To change the selection or cancel an incorrect entry, scan Cancel in
appendix

Code 93 - One Discrete Length

Two Discrete Lengths

Select this option to decode only those codes containing two selected lengths. For example, select Code 93
Two Discrete Lengths, then scan 0, 2, 1, 4, to limit the decoding to only Code 93 symbols containing 2 or 14
characters. Numeric Bar Codes is in appendix. To change the selection or cancel an incorrect entry, scan
Cancel in appendix.

Code 93 - Two Discrete Lengths

- 28 -
Length Within Range
This option sets the unit to decode a code type within a specified range. For example, to decode Code 93
symbols containing between 4 and 12 characters, first scan Code 93 Length Within Range, then scan 0, 4, 1
and 2 (single digit numbers must always be preceded by a leading zero). Numeric Bar Codes is in appendix. To
change the selection or cancel an incorrect entry, scan Cancel in appendix..

Code 93 - Length Within Range

Any Length
Scan this option to decode Code 93 symbols containing any number of characters

Code 93 - Any Length

Code 93 Check Digit Verification

*Verify Code 93 Check Digit

Do Not Verify Code 39 Check Digit

Transmit Code 93 Check Digit

- 29 -
 Transmit Code 93 Check Digit (Enable)

*Do Not Transmit Code 93 Check Digit

Code 11
Enable/Disable Code 11
To enable or disable Code 11, scan the appropriate bar code below.

Enable Code 11

*Disable Code 11

Set Lengths for Code 11

The length of a code refers to the number of characters (i.e., human readable characters), including check
digit(s) the code contains. Set lengths for Code 11 to any length, one or two discrete lengths, or lengths within
a specific range

One Discrete Length

Select this option to decode only Code 11 symbols containing a selected length. Select the length using the
Numeric Bar Codes in appendix. For example, to decode only Code 11 symbols with 14 characters, scan Code
11 - One Discrete Length, then scan 1 followed by 4. To correct an error or to change the selection, scan
Cancel in appendix.

Code 11 - One Discrete Length

- 30 -
Two Discrete Lengths
Select this option to decode only Code 11 symbols containing either of two selected lengths. Select lengths using
the Numeric Bar Codes in appendix. For example, to decode only those Code 11 symbols containing either 2 or 14
characters, select Code 11 - Two Discrete Lengths, then scan 0, 2, 1, and then 4. To correct an error or to change
the selection, scan Cancel in appendix.

Code 11 - Two Discrete Lengths

Length Within Range

Select this option to decode a Code 11 symbol with a specific length range. Select lengths using the Numeric Bar
Codes in appendix. For example, to decode Code 11 symbols containing between 4 and 12 characters, first scan
Code 11 - Length Within Range. Then scan 0, 4, 1, and 2 (single digit numbers must always be preceded by a
leading zero). To correct an error or change the selection, scan Cancel in appendix.

Code 11 - Length Within Range

Any Length
Scan this option to decode Code 11 symbols containing any number of characters within the scan engine capability.

Code 11 - Any Length

Code 11 Check Digit Verification

This feature allows the scan engine to check the integrity of all Code 11 symbols to verify that the data
complies with the specified check digit algorithm. This selects the check digit mechanism for the decoded
Code 11 bar code. The options are to check for one check digit, check for two check digits, or disable the
feature.

* Disable Code 11 Check Digit Verification

- 31 -
 Enable One Check Digit

Enable Two Check Digits

Transmit Code 11 Check Digits

Transmit Code 11 Check Digit(s) (Enable)

*Do Not Transmit Code 11 Check Digit(s) (Disable)

Interleaved 2 of 5/ITF
Enable/Disable Interleaved 2 of 5
To enable or disable Interleaved 2 of 5, scan the appropriate bar code below.

*Enable Interleaved 2 of 5

- 32 -
 Disable Interleaved 2 of 5

Set Lengths for Interleaved 2 of 5

The length of a code refers to the number of characters (i.e., human readable characters), including check
digit(s) the code contains. Lengths for I 2 of 5 may be set for any length, one or two discrete lengths, or
lengths within a specific range.

One Discrete Length

Select this option to decode only those codes containing a selected length. For example, select I 2 of 5 One
Discrete Length, then scan 1, 4, to decode only D 2 of 5 symbols containing 14 characters. Numeric Bar Codes
is in appendix. To change the selection or cancel an incorrect entry, scan Cancel in appendix.

I 2 of 5 - One Discrete Length

Two Discrete Lengths

Select this option to decode only those codes containing two selected lengths. For example,select I 2 of 5
Two Discrete Lengths, then scan 0, 6, 1, 4, to decode only I 2 of 5 symbols containing 6 or 14 characters.
Numeric Bar Codes is in appendix. To change the selection or cancel an incorrect entry, scan Cancel in
appendix

I 2 of 5 - Two Discrete Lengths

Length Within Range

Select this option to decode only codes within a specified range. For example, to decode I 2 of 5 symbols
containing between 4 and 12 characters, first scan I 2 of 5 Length Within Range, then scan 0, 4, 1 and 2 (single
digit numbers must always be preceded by a leading zero). Numeric Bar Codes is in appendix. To change the
selection or cancel an incorrect entry, scan Cancel in appendix.

I 2 of 5 - Length Within Range

- 33 -
Any Length
Scan this option to decode I 2 of 5 symbols containing any number of characters.
NOTE Selecting this option may lead to misdecodes for I 2 of 5 codes

I 2 of 5 - Any Length

I 2 of 5 Check Digit Verification

Verify I 2 of 5 Check Digit

*Do Not Verify I 2 of 5 Check Digit

Transmit I 2 of 5 Check Digit

Transmit I 2 of 5 Check Digit (Enable)

*Do Not Transmit I 2 of 5 Check Digit

- 34 -
ITF14
Enable/Disable ITF14
To enable or disable ITF14, scan the appropriate bar code below.

Enable ITF14

*Disable ITF14

Transmit ITF14 Check Digit

Transmit ITF14 Check Digit (Enable)

*Do Not Transmit ITF14 Check Digit

Discrete 2 of 5/Industrial 2 of 5/IND25

Enable/Disable Discrete 2 of 5
To enable or disable Discrete 2 of 5, scan the appropriate bar code below.

Enable Discrete 2 of 5

- 35 -
 *Disable Discrete 2 of 5

Set Lengths for Discrete 2 of 5

The length of a code refers to the number of characters (i.e., human readable characters), including check
digit(s) the code contains. Lengths for D 2 of 5 may be set for any length, one or two discrete lengths, or
lengths within a specific range.

One Discrete Length

Select this option to decode only those codes containing a selected length. For example, select D 2 of 5 One
Discrete Length, then scan 1, 4, to decode only D 2 of 5 symbols containing 14 characters. Numeric Bar Codes
is in appendix. To change the selection or cancel an incorrect entry, scan Cancel in appendix.

D 2 of 5 - One Discrete Length

Two Discrete Lengths

Select this option to decode only those codes containing two selected lengths. For example, select D 2 of 5 Two
Discrete Lengths, then scan 0, 2, 1, 4, to decode only D 2 of 5 symbols containing 2 or 14 characters. Numeric Bar
Codes is in appendix. To change the selection or cancel an incorrect entry, scan Cancel in appendix

D 2 of 5 - Two Discrete Lengths

Length Within Range

Select this option to decode codes within a specified range. For example, to decode D 2 of 5 symbols containing
between 4 and 12 characters, first scan D 2 of 5 Length Within Range, then scan 0, 4, 1 and 2 (single digit numbers
must be preceded by a leading zero). Numeric Bar Codes is in appendix. To change the selection or cancel an
incorrect entry, scan Cancel in appendix.

D 2 of 5 - Length Within Range

- 36 -
Any Length
Scan this option to decode D 2 of 5 symbols containing any number of characters.
NOTE Selecting this option may lead to misdecodes for D 2 of 5 codes.

D 2 of 5 - Any Length

Discrete 2 of 5 Check Digit Verification

Verify D 2 of 5 Check Digit

*Do Not Verify D 2 of 5 Check Digit

Transmit Discrete 2 of 5 Check Digit

Transmit D 2 of 5 Check Digit (Enable)

*Do Not Transmit D 2 of 5 Check Digit

- 37 -
Matrix 25
Enable/Disable Matrix 25
To enable or disable Matrix 25, scan the appropriate bar code below.

Enable Matrix 25

*Disable Matrix 25

Matrix 25 Check Digit Verification

Verify Matrix 25 Check Digit

*Do Not Verify Matrix 25 Check Digit

Transmit Matrix 25 Check Digit

- 38 -
 Transmit Matrix 25 Check Digit (Enable)

*Do Not Transmit Matrix 25 Check Digit

Set Lengths for Matrix 25

The length of a code refers to the number of characters (i.e., human readable characters), including check
digit(s) the code contains. Lengths for Matrix 25 may be set for any length, one or two discrete lengths, or
lengths within a specific range.

One Discrete Length

Select this option to decode only those codes containing a selected length. For example, select Matrix 25 One
Discrete Length, then scan 1, 4, to decode only Matrix 25 symbols containing 14 characters. Numeric Bar
Codes is in appendix. To change the selection or cancel an incorrect entry, scan Cancel in appendix.

Matrix 25 - One Discrete Length

Two Discrete Lengths

Select this option to decode only those codes containing two selected lengths. For example, select Matrix 25
Two Discrete Lengths, then scan 0, 2, 1, 4, to decode only Matrix 25 symbols containing 2 or 14 characters.
Numeric Bar Codes is in appendix. To change the selection or cancel an incorrect entry, scan Cancel in
appendix.

Matrix 25 - Two Discrete Lengths

- 39 -
Length Within Range
Select this option to decode codes within a specified range. For example, to decode Matrix 25 symbols
containing between 4 and 12 characters, first scan Matrix 25 Length Within Range, then scan 0, 4, 1 and 2
(single digit numbers must be preceded by a leading zero). Numeric Bar Codes is in appendix. To change the
selection or cancel an incorrect entry, scan Cancel in appendix.

Matrix 25 - Length Within Range

Any Length
Scan this option to decode Matrix 25 symbols containing any number of characters.
NOTE Selecting this option may lead to misdecodes for Matrix 25 codes.

Matrix 25 - Any Length

Standard 25/IATA 25
Enable/Disable Standard 25
To enable or disable Standard 25, scan the appropriate bar code below.

*Disable Standard 25

Enable Standard 25

- 40 -
Standard 25 Check Digit Verification

*Disable Standard 25 Check Digit Verification

Enable Standard 25 Check Digit Verification

Standard 25 Transmit Check Character

*Disable Standard 25 Transmit Check Character

Enable Standard 25 Transmit Check Character

Set Lengths for Standard 25

The length of a code refers to the number of characters (i.e., human readable characters), including check
digit(s) the code contains. Lengths for Standard 25 may be set for any length, one or two discrete lengths, or
lengths within a specific range.

- 41 -
One Discrete Length
Select this option to decode only those codes containing a selected length. For example, select Standard 25
One Discrete Length, then scan 1, 4, to decode only Standard 25 symbols containing 14 characters. Numeric
Bar Codes is in appendix. To change the selection or cancel an incorrect entry, scan Cancel in appendix.

Standard 25 - One Discrete Length

Two Discrete Lengths

Select this option to decode only those codes containing two selected lengths. For example, select Standard
25 Two Discrete Lengths, then scan 0, 2, 1, 4, to decode only Standard 25 symbols containing 2 or 14
characters. Numeric Bar Codes is in appendix. To change the selection or cancel an incorrect entry, scan
Cancel in appendix.

Standard 25 - Two Discrete Lengths

Length Within Range

Select this option to decode codes within a specified range. For example, to decode Standard 25 symbols
containing between 4 and 12 characters, first scan Standard 25 Length Within Range, then scan 0, 4, 1 and 2
(single digit numbers must be preceded by a leading zero). Numeric Bar Codes is in appendix. To change the
selection or cancel an incorrect entry, scan Cancel in appendix.

Standard 25 - Length Within Range

Any Length
Scan this option to decode Standard 25 symbols containing any number of characters.
NOTE Selecting this option may lead to misdecodes for Standard 25 codes.

Standard 25 - Any Length

- 42 -
Codabar
Enable/Disable Codabar
To enable or disable Codabar, scan the appropriate bar code below.

Enable Codabar

*Disable Codabar

Set Lengths for Codabar

The length of a code refers to the number of characters (i.e., human readable characters), including check
digit(s) the code contains. Lengths for Codabar may be set for any length, one or two discrete lengths, or
lengths within a specific range.

One Discrete Length

Select this option to decode only those codes containing a selected length. For example, select Codabar One
Discrete Length, then scan 1, 4, to decode only Codabar symbols containing 14 characters. Numeric Bar Codes
is in appendix. To change the selection or cancel an incorrect entry, scan Cancel in appendix.

Codabar - One Discrete Length Codabar

Two Discrete Lengths

This option sets the unit to decode only those codes containing two selected lengths. For example, select
Codabar Two Discrete Lengths, then scan 0, 2, 1, 4, to decode only Codabar symbols containing 6 or 14
characters. Numeric Bar Codes is in appendix. To change the selection or cancel an incorrect entry, scan
Cancel in appendix.

Codabar - Two Discrete Lengths Codabar

- 43 -
Length Within Range
Select this option to decode a code within a specified range. For example, to decode Codabar symbols
containing between 4 and 12 characters, first scan Codabar Length Within Range, then scan 0, 4, 1 and 2
(single digit numbers must always be preceded by a leading zero). Numeric Bar Codes is in appendix. To
change the selection or cancel an incorrect entry, scan Cancel in appendix

Codabar - Length Within Range Codabar -

Any Length
Scan this option to decode Codabar symbols containing any number of characters.

Codabar - Any Length Codabar

Codabar Check Digit Verification

*Disable Codabar Check Digit Verification

Enable Codabar Check Digit Verification

Codabar Transmit Check Character

*Disable Codabar Transmit Check Character

- 44 -
 Enable Codabar Transmit Check Character

Start/Stop Character Format

You can choose your desired start/stop character format by scanning the appropriate barcode below.

* ABCD/ABCD as the Start/Stop Character ABCD/TN*E as the Start/Stop Character

*Start/Stop Character in Uppercase Start/Stop Character in Lowercase

MSI
Enable/Disable MSI
To enable or disable MSI, scan the appropriate bar code below.

Enable MSI

*Disable MSI

Set Lengths for MSI

The length of a code refers to the number of characters (i.e., human readable characters) the code contains,
and includes check digits. Lengths for MSI can be set for any length, one or two discrete lengths, or lengths
within a specific range.

- 45 -
One Discrete Length
Select this option to decode only those codes containing a selected length. For example, select MSI Plessey
One Discrete Length, then scan 1, 4, to decode only MSI Plessey symbols containing 14 characters. Numeric
Bar Codes is in Appendix.

MSI - One Discrete Length

Two Discrete Lengths

Select this option to decode only those codes containing two selected lengths. For example, select MSI
Plessey Two Discrete Lengths, then scan 0, 6, 1, 4, to decode only MSI Plessey symbols containing 6 or 14
characters. Numeric Bar Codes is in appendix. To change the selection or cancel an incorrect entry, scan
Cancel in appendix

MSI - Two Discrete Lengths

Length Within Range

Select this option to decode codes within a specified range. For example, to decode MSI symbols containing
between 4 and 12 characters, first scan MSI Length Within Range, then scan 0, 4, 1 and 2 (single digit
numbers must always be preceded by a leading zero). Numeric Bar Codes is in appendix. To change the
selection or cancel an incorrect entry, scan Cancel in appendix.

MSI - Length Within Range

Any Length
Scan this option to decode MSI Plessey symbols containing any number of characters.
NOTE Selecting this option may lead to misdecodes for MSI codes.

MSI - Any Length

- 46 -
MSI Check Character Verification

* One Check Character Two Check Characters

MSI Transmit Check Character

Transmit Check Character * Do Not Transmit Check Character

GS1 DataBar/RSS
Enable/Disable GS1 DataBar-14
To enable or disable GS1 DataBar-14, scan the appropriate bar code below.

Enable GS1 DataBar-14

*Disable GS1 DataBar-14

Enable/Disable GS1 DataBar Limited

To enable or disable GS1 DataBar Limited, scan the appropriate bar code below.

- 47 -
 Enable GS1 DataBar Limited

*Disable GS1 DataBar Limited

Enable/Disable GS1 DataBar Expanded
To enable or disable GS1 DataBar Expanded, scan the appropriate bar code below.

Enable GS1 DataBar Expanded

*Disable GS1 DataBar Expanded

PDF417
Enable/Disable PDF417
To enable or disable PDF417, scan the appropriate bar code below.

Disable PDF417

- 48 -
 *Enable PDF417

PDF 417 Twin Code

PDF417 twin code is 2 PDF417 barcodes paralleled vertically or horizontally. They must both be either
regular or inverse barcodes. They must have similar specifications and be placed closely together.
There are 3 options for reading PDF417 twin codes:

Single PDF417 Only: Read either PDF417 code.

Twin PDF417 Only: Read both PDF417 codes.
Both Single & Twin: Read both PDF417 codes. If successful, transmit as twin PDF417 only. Otherwise,
try single PDF417 only.

*Single PDF417 Only Twin PDF417 Only

Both Single & Twin

Read Normal Phase/ Phase Reversal

*Read Normal Phase

- 49 -
 Read Phase Reversal

Read Normal Phase/ Phase Reversal

QR
Read normal phase/ phase reversal/ mirror image picture

Enable/Disable QR
To enable or disable QR, scan the appropriate bar code below.

Disable QRCode

*Enable QR Code

QR Twin Code

*Single QR Only Twin QR Only

- 50 -
 Both Single & Twin

Enable/Disable QR ECI Output

*Disable QR ECI Output Enable QR ECI Output

Read Normal Phase/ Phase Reversal

*Read Normal Phase

Read Phase Reversal

Read Normal Phase/ Phase Reversal

Data Matrix(DM)
Scan normal or mirror image picture.

Enable/Disable Data Matrix(DM)

To enable or disable Data Matrix(DM), scan the appropriate bar code below.

- 51 -
 Disable Data Matrix

*Enable Data Matrix

Data Matrix Twin Code

*Single Data Matrix Only Twin Data Matrix Only

Both Single & Twin

Enable/Disable Data Matrix ECI Output

*Disable Data Matrix ECI Output Enable Data Matrix ECI Output

- 52 -
Read Normal Phase/ Phase Reversal

*Read Normal Phase

Read Phase Reversal

Read Normal Phase/ Phase Reversal

Maxi Code
Enable/Disable Maxi Code
To enable or disable Maxi Code, scan the appropriate bar code below.

*Disable MaxiCode

Enable MaxiCode

Aztec Code

- 53 -
Enable/Disable Aztec Code
To enable or disable Aztec Code, scan the appropriate bar code below.

*Disable Aztec Code

Enable Aztec Code

Han Xin Code

Enable/Disable Han Xin Code
To enable or disable Han Xin Code, scan the appropriate bar code below.

*Disable Han Xin Code

Enable Han Xin Code

Han Xin Twin Code

*Single Han Xin Only Twin Han Xin Only

- 54 -
 Both Single & Twin

Read Normal Phase/ Phase Reversal

*Read Normal Phase

Read Phase Reversal

Read Normal Phase/ Phase Reversal

Plessey
Enable/Disable Plessey
To enable or disable Plessey, scan the appropriate bar code below.

Enable Plessey

- 55 -
 *Disable Plessey

Check Character Verification

Enable Character Verification * Disable Character Verification

Transmit Check Character

Transmit Check Character * Do Not Transmit Check Character

Brazil Bank Code

Enable/Disable Brazil Bank Code
Only applied to 1D barcode, To enable or disable Han Xin Code, scan the appropriate bar code below.

Enable Brazil Bank Code * Disable Brazil Bank Code

COMPOSITE
Enable/Disable COMPOSITE
To enable or disable Plessey, scan the appropriate bar code below.

- 56 -
 Enable COMPOSITE Code * Disable COMPOSITE Code

EAN/UCC
Enable/Disable EAN/UCC
To enable or disable EAN/UCC, scan the appropriate bar code below.

Enable EAN/UCC Code * Disable EAN/UCC Code

Appendix 1: Numeric Bar Codes

- 57 -
 4

- 58 -
Cancel Barcode
To change the selection or cancel an incorrect entry, scan the barcode below.

Cancel

Hide Prefix or suffix digits

The start/middle/end of barcode chars can be hidden. After scan below hide set barcode, scan a double-digit
hexadecimal number that you want to hide char length(00~FF e.g. hide length 4, scan 0, 4).

Hide Barcode Start Chars

Hide Barcode Middle Char Start

Hide Barcode Middle Chars

Hide Barcode End Chars

Output Format

To change the Scan Data Transmission Format, scan one of the eight bar codes corresponding to the desired
format.

Enable Hide Barcode Start Char

- 59 -
 Enable Hide Barcode Middle Char

Enable Hide Barcode End Char

To Hide chars of barcode Start/Middle/End:

Procedures
1. Scan the Hide Barcode Start / Middle Start / Middle length / End Chars symbol.
2. Determine the hex value for the length you wish to enter(hide 4 chars, scan 0,4; hide 12 chars, scan 0,C).
3. Scan the 2 digit hex value from the Numeric Bar Codes
4. Scan the output format to enable or cancel hide char function.

Custom prefix and suffix

Maximum 20 prefixes and 20 suffixes can be added to scan data for use in data editing. To set these values,
scan a double-digit hexadecimal number (i.e. two bar codes) that corresponds to ASCII values. See the Table 1
and Numeric Bar Codes in appendix.

To Add a Prefix or Suffix:

1. Scan command barcode of " Add Prefix" or" Add Suffix ".
2. Check the prefix or suffix hex value from the ASCII Chart.
3. Scan the 2 digit hex value from the Numeric Bar Codes
4. Repeat Steps 2 and 3 for all the prefix or suffix that you want to add.
5. Scan the output format to enable or disable prefix/suffix output.

Add Prefix

Add Suffix

Clear All Prefix

- 60 -
 Clear All Suffix

Numeric Bar Codes

- 61 -
Output Format
To change the Scan Data Transmission Format, scan one of the eight bar codes corresponding to the desired format.

*Default output format

Enable Suffix output

- 62 -
 Enable Prefix output

Example on how to add normal prefix or suffix on barcode "123456789"

Add " A" and "B" as prefixes and "!" as suffix

1. Scan command barcode of " Add Prefix"

2. Check the prefix hex value from the ASCII Chart. A- "4","1"; B-"4" "2";
3. Scan the 2 digit hex value from the Numeric Bar Codes

4. Scan the output format to enable prefix output.

Enable Prefix output

5. Scan command barcode of " Add Suffix" to add "!" as suffix.

- 63 -
 Add Suffix

6. Check the suffix hex value from the ASCII Chart. !- "2" "1"
7. Scan the 2 digit hex value from the Numeric Bar Codes.

8. Scan the output format to enable suffix output.

Enable Suffix output

9. Scan the barcode then you will get AB123456789!

Example on how to add Combination Key suffix for barcode "123456789"

Add "Ctrl+P" on "123456789" as suffix

1.Scan command barcode of " Add Suffix" to add "Ctrl+P" as suffix.

Add Suffix
2. Check the suffix hex value from the ASCII Chart. Ctrl+P - "9" "7" "5" "0"

3. Scan the 4 digits hex value from the Numeric Bar Codes.

- 64 -
4. Scan the output format to enable suffix output.

Enable Suffix output

5. Scan " Keyboard Ctrl Combination Key"

6. Scan the barcode 123456789. (test it on Excel)

Table 1. ASCII Character Equivalents

HEX ASCII HEX ASCII HEX ASCII HEX ASCII

20H Space 30H 0 40H @ 50H P
21H ! 31H 1 41H A 51H Q
22H " 32H 2 42H B 52H R
23H # 33H 3 43H C 53H S
24H $ 34H 4 44H D 54H T
25H % 35H 5 45H E 55H U
26H & 36H 6 46H F 56H V
27H ' 37H 7 47H G 57H W
28H ( 38H 8 48H H 58H X
29H ) 39H 9 49H I 59H Y
2AH * 3AH : 4AH J 5AH Z
2BH + 3BH ; 4BH K 5BH [
2CH , 3CH < 4CH L 5CH \
2DH - 3DH = 4DH M 5DH ]
2EH . 3EH > 4EH N 5EH ^
2FH / 3FH ? 4FH O 5FH _
60H ` 70H p 80H F1 90H End

- 65 -
 61H a 71H q 81H F2 91H Page Down
62H b 72H r 82H F3 92H Right Arrow
63H c 73H s 83H F4 93H Left Arrow
64H d 74H t 84H F5 94H Down Arrow
65H e 75H u 85H F6 95H Up Arrow
66H f 76H v 86H F7 96H Print Screen
67H g 77H w 87H F8 97H *Ctrl
68H h 78H x 88H F9 98H *Shirt
69H i 79H y 89H F10 99H *Left Alt
6AH J 7AH z 8AH F11 9AH *Right Alt
6BH k 7BH { 8BH F12 08H BS
6CH l 7CH 8CH Insert 09H HT

6DH m 7DH } 8DH Home 0AH LF

6EH n 7EH ~ 8EH Page Up 0DH CR
6FH o 7FH DEL 8FH Delete 1BH ESC

Support
For any inquiries concerning our products, please send an email to
[email protected], and we will respond to you as soon as possible.

Contact Information
Whatsapp: +86 188 2626 1132
Tel.:+0086 20-6626-0708
Email:[email protected]
Addr.:Unit 137, The Pacific Industry Park, Xintang Town,Zengcheng District,
Guangzhou,China/511340

Made in China

- 66 -