Designation: A 322 – 07

Standard Specification for

Steel Bars, Alloy, Standard Grades1
This standard is issued under the fixed designation A 322; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (e) indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.

1. Scope* 3.1.1 Quantity (weight or number of bars),

1.1 This specification covers hot-wrought alloy steel bars. 3.1.2 Name of material (hot-wrought alloy steel bars),
Bar applications include forging, heat treating, cold drawing, 3.1.3 Dimensions,
machining and many structural components (Note 1). 3.1.4 ASTM designation,
3.1.5 Deoxidation practice (see 5.3),
NOTE 1—A guide for the selection of steel bars is contained in Practice 3.1.6 Grade designation or chemical composition limits (see
A 400.
6.1 and Table 1),
1.2 The bars shall be furnished in the grades specified in 3.1.7 Grain size if required,
Table 1. Sections and sizes of bar steel available are covered in 3.1.8 Test reports, if required (Section 8),
Specification A 29/A 29M. Hot-wrought alloy steel bars are 3.1.9 Additions to the specification and Supplementary
produced in cut lengths and coils; the manufacturer should be Requirements, if required, and
consulted regarding sections and sizes available in coils, 3.1.10 Application.
produced to a chemical composition.
1.3 Some applications may require superior surface quality, 4. General Requirements
or special chemical restrictions, metallurgical characteristics, 4.1 Material furnished under this specification shall con-
heat treatment, or surface finishes which the purchaser may form to the applicable requirements of the current edition of
obtain by designating one or more of the available Supplemen- Specification A 29/A 29M, unless otherwise provided herein.
tary Requirements.
5. Materials and Manufacture
2. Referenced Documents 5.1 The steel shall be made by one or more of the following
2.1 ASTM Standards: 2 primary processes: open-hearth, basic-oxygen, or electric-
A 29/A 29M Specification for Steel Bars, Carbon and Alloy, furnace. The primary melting may incorporate separate degas-
Hot-Wrought, General Requirements for sing or refining and may be followed by secondary melting
A 304 Specification for Carbon and Alloy Steel Bars Sub- using electro-slag remelting or vacuum arc remelting. Where
ject to End-Quench Hardenability Requirements secondary melting is employed, the heat shall be defined as all
A 400 Practice for Steel Bars, Selection Guide, Composi- of the cast product remelted from a single primary heat.
tion, and Mechanical Properties 5.2 The steel shall be furnished as strand cast or ingot cast,
E 112 Test Methods for Determining Average Grain Size unless otherwise specified.
E 381 Method of Macroetch Testing Steel Bars, Billets, 5.2.1 Discard—A sufficient discard shall be made to secure
Blooms, and Forgings freedom from injurious piping and undue segregation.
E 527 Practice for Numbering Metals and Alloys (UNS) 5.3 Deoxidation—Killed steel is required.
5.3.1 The purchaser may designate that the steel be made to
3. Ordering Information coarse or fine austenitic grain size. (See Supplementary Re-
3.1 Orders under this specification should include the fol- quirement S9 or S10.)
lowing as required to describe adequately the desired material: 5.4 Slow Cooling—Immediately after hot forming, the bars
shall be allowed to cool to a temperature below the critical
1
range under suitable conditions to prevent imperfections
This specification is under the jurisdiction of ASTM Committee A01 on Steel,
Stainless Steel and Related Alloys and is the direct responsibility of Subcommittee caused by too rapid cooling.
A01.15 on Bars. 5.5 Thermal Treatment—Various thermal treatments such as
Current edition approved May 1, 2007. Published May 2007. Originally annealing, stress relief, quench and temper, normalize, etc., are
approved in 1947. Last previous edition approved in 2006 as A 322 – 06.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
available. Such treatments must be specified as a Supplemen-
contact ASTM Customer Service at [email protected]. For Annual Book of ASTM tary Requirement.
Standards volume information, refer to the standard’s Document Summary page on
the ASTM website.

*A Summary of Changes section appears at the end of this standard.

Copyright © ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.

1
 A 322 – 07
6. Chemical Composition
6.1 The heat analysis shall conform to the requirements for
chemical composition in Table 1 for the grade specified.

TABLE 1 Grade Designations and Chemical Compositions of Hot-Wrought Alloy Steel BarsA,B

UNS GradeD Chemical Composition, Ranges and Limits, %

DesignationC Designations
Carbon Manganese Phospho- Sulfur,E SiliconF Nickel Chromium Molybdenum
rus, max max
G13300 1330 0.28–0.33 1.60–1.90 0.035 0.040 0.15–0.35 ... ... ...
G13350 1335 0.33–0.38 1.60–1.90 0.035 0.040 0.15–0.35 ... ... ...
G13400 1340 0.38–0.43 1.60–1.90 0.035 0.040 0.15–0.35 ... ... ...
G13450 1345 0.43–0.48 1.60–1.90 0.035 0.040 0.15–0.35 ... ... ...
G40230 4023 0.20–0.25 0.70–0.90 0.035 0.040 0.15–0.35 ... ... 0.20–0.30
G40240 4024 0.20–0.25 0.70–0.90 0.035 0.035– 0.15–0.35 ... ... 0.20–0.30
0.050
G40270 4027 0.25–0.30 0.70–0.90 0.035 0.040 0.15–0.35 ... ... 0.20–0.30
G40280 4028 0.25–0.30 0.70–0.90 0.035 0.035– 0.15–0.35 ... ... 0.20–0.30
0.050
G40370 4037 0.35–0.40 0.70–0.90 0.035 0.040 0.15–0.35 .. ... 0.20–0.30
G40470 4047 0.45–0.50 0.70–0.90 0.035 0.040 0.15–0.35 ... ... 0.20–0.30
G41180 4118 0.18–0.23 0.70–0.90 0.035 0.040 0.15–0.35 ... 0.40–0.60 0.08–0.15
G41200 0.18–0.23 0.90–1.20 0.035 0.040 0.15–0.35 ... 0.40–0.60 0.13–0.20
G41210 0.18–0.23 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.45–0.65 0.20–0.30
G41300 4130 0.28–0.33 0.40–0.60 0.035 0.040 0.15–0.35 ... 0.80–1.10 0.15–0.25
G41370 4137 0.35–0.40 0.70–0.90 0.035 0.040 0.15–0.35 ... 0.80–1.10 0.15–0.25
G41400 4140 0.38–0.43 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.80–1.10 0.15–0.25
G41420 4142 0.40–0.45 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.80–1.10 0.15–0.25
G41450 4145 0.43–0.48 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.80–1.10 0.15–0.25
G41470 4147 0.45–0.50 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.80–1.10 0.15–0.25
G41500 4150 0.48–0.53 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.80–1.10 0.15–0.25
G41610 4161 0.56–0.64 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.70–0.90 0.25–0.35
G43200 4320 0.17–0.22 0.45–0.65 0.035 0.040 0.15–0.35 1.65–2.00 0.40–0.60 0.20–0.30
G43400 4340 0.38–0.43 0.60–0.80 0.035 0.040 0.15–0.35 1.65–2.00 0.70–0.90 0.20–0.30
G43406 E4340 0.38–0.43 0.65–0.85 0.025 0.025 0.15–0.35 1.65–2.00 0.70–0.90 0.20–0.30
G46150 4615 0.13–0.18 0.45–0.65 0.035 0.040 0.15–0.35 1.65–2.00 ... 0.20–0.30
G46200 4620 0.17–0.22 0.45–0.65 0.035 0.040 0.15–0.35 1.65–2.00 ... 0.20–0.30
G46210 4621 0.18–0.23 0.70–0.90 0.035 0.040 0.15–0.35 1.65–2.00 ... 0.20–0.30
G46260 4626 0.24–0.29 0.45–0.65 0.035 0.040 0.15–0.35 0.70–1.00 ... 0.15–0.25
G47150 0.13–0.18 0.70–0.90 0.035 0.040 0.15–0.35 0.70–1.00 0.45–0.65 0.45–0.60
G47200 4720 0.17–0.22 0.50–0.70 0.035 0.040 0.15–0.35 0.90–1.20 0.35–0.55 0.15–0.25
G48150 4815 0.13–0.18 0.40–0.60 0.035 0.040 0.15–0.35 3.25–3.75 ... 0.20–0.30
G48170 4817 0.13–0.20 0.40–0.60 0.035 0.040 0.15–0.35 3.25–3.75 ... 0.20–0.30
G48200 4820 0.18–0.23 0.50–0.70 0.035 0.040 0.15–0.35 3.25–3.75 ... 0.20–0.30
G51170 5117 0.15–0.20 0.70–0.90 0.035 0.040 0.15–0.35 ... 0.70–0.90 ...
G51200 5120 0.17–0.22 0.70–0.90 0.035 0.040 0.15–0.35 ... 0.70–0.90 ...
G51300 5130 0.28–0.33 0.70–0.90 0.035 0.040 0.15–0.35 ... 0.80–1.10 ...
G51320 5132 0.30–0.35 0.60–0.80 0.035 0.040 0.15–0.35 ... 0.75–1.00 ...
G51350 5135 0.33–0.38 0.60–0.80 0.035 0.040 0.15–0.35 ... 0.80–1.05 ...
G51400 5140 0.38–0.43 0.70–0.90 0.035 0.040 0.15–0.35 ... 0.70–0.90 ...
G51500 5150 0.48–0.53 0.70–0.90 0.035 0.040 0.15–0.35 ... 0.70–0.90 ...
G51550 5155 0.51–0.59 0.70–0.90 0.035 0.040 0.15–0.35 ... 0.70–0.90 ...
G51600 5160 0.56–0.64 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.70–0.90 ...
G51986 E51100 0.98–1.10 0.25–0.45 0.025 0.025 0.15–0.35 ... 0.90–1.15 ...
G52986 E52100 0.98–1.10 0.25–0.45 0.025 0.025 0.15–0.35 ... 1.30–1.60 ...
Vanadium
G61180 6118 0.16–0.21 0.50–0.70 0.035 0.040 0.15–0.35 ... 0.50–0.70 0.10–0.15
G61500 6150 0.48–0.53 0.70–0.90 0.035 0.040 0.15–0.35 ... 0.80–1.10 0.15 min
Molybdenum
G86150 8615 0.13–0.18 0.70–0.90 0.035 0.04 0.15–0.35 0.40–0.70 0.40–0.60 0.15–0.25
G86170 8617 0.15–0.20 0.70–0.90 0.035 0.040 0.15–0.35 0.40–0.70 0.40–0.60 0.15–0.25
G86200 8620 0.18–0.23 0.70–0.90 0.035 0.04 0.15–0.35 0.40–0.70 0.40–0.60 0.15–0.25
G86220 8622 0.20–0.25 0.70–0.90 0.035 0.040 0.15–0.35 0.40–0.70 0.40–0.60 0.15–0.25
G86250 8625 0.23–0.28 0.70–0.90 0.035 0.040 0.15–0.35 0.40–0.70 0.40–0.60 0.15–0.25
G86270 8627 0.25–0.30 0.70–0.90 0.035 0.040 0.15–0.35 0.40–0.70 0.40–0.60 0.15–0.25
G86300 8630 0.28–0.33 0.70–0.90 0.035 0.040 0.15–0.35 0.40–0.70 0.40–0.60 0.15–0.25
G86370 8637 0.35–0.40 0.75–1.00 0.035 0.040 0.15–0.35 0.40–0.70 0.40–0.60 0.15–0.25
G86400 8640 0.38–0.43 0.75–1.00 0.035 0.040 0.15–0.35 0.40–0.70 0.40–0.60 0.15–0.25
G86420 8642 0.40–0.45 0.75–1.00 0.035 0.040 0.15–0.35 0.40–0.70 0.40–0.60 0.15–0.25
G86450 8645 0.43–0.48 0.75–1.00 0.035 0.040 0.15–0.35 0.40–0.70 0.40–0.60 0.15–0.25
G86550 8655 0.51–0.59 0.75–1.00 0.035 0.040 0.15–0.35 0.40–0.70 0.40–0.60 0.15–0.25
G87200 8720 0.18–0.23 0.70–0.90 0.035 0.040 0.15–0.35 0.40–0.70 0.40–0.60 0.20–0.30
G87400 8740 0.38–0.43 0.75–1.00 0.035 0.040 0.15–0.35 0.40–0.70 0.40–0.60 0.20–0.30

2
 A 322 – 07

TABLE 1 Continued
D
UNS Grade Chemical Composition, Ranges and Limits, %
DesignationC Designations
Carbon Manganese Phospho- Sulfur,E SiliconF Nickel Chromium Molybdenum
rus, max max
G88220 8822 0.20–0.25 0.75–1.00 0.035 0.040 0.15–0.35 0.40–0.70 0.40–0.60 0.30–0.40
G92590 9259 0.56–0.64 0.75–1.00 0.035 0.040 0.70–1.10 ... 0.45–0.65 ...
G92600 9260 0.56–0.64 0.75–1.00 0.035 0.040 1.80–2.20 ... ... ...
Standard Boron SteelsG
G50441 50B44 0.43–0.48 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.20–0.60 ...
G50461 50B46 0.44–0.49 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.20–0.35 ...
G50501 50B50 0.48–0.53 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.40–0.60 ...
G50601 50B60 0.56–0.64 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.40–0.60 ...
G51601 51B60 0.56–0.64 0.75–1.00 0.035 0.040 0.15–0.35 ... 0.70–0.90 ...
G81451 81B45 0.43–0.48 0.75–1.00 0.035 0.040 0.15–0.35 0.20–0.40 0.35–0.55 0.08–0.15
G94171 94B17 0.15–0.20 0.75–1.00 0.035 0.040 0.15–0.35 0.30–0.60 0.30–0.50 0.08–0.15
G94301 94B30 0.28–0.33 0.75–1.00 0.035 0.040 0.15–0.35 0.30–0.60 0.30–0.50 0.08–0.15
A
Small quantities of certain elements are present in alloy steels which are not specified or required. These elements are considered as incidental and may be present
to the following maximum amounts: copper 0.35 %, nickel 0.25 %, chromium 0.20 %, and molybdenum 0.06 %.
B
Standard alloy steels can be produced with a lead range of 0.15 to 0.35 %. Such steels are identified by inserting the letter “L” between the second and third numerals
of the number, that is, 41L40. A cast or heat analysis is not determinable when lead is added to the ladle stream.
C
New designation established in accordance with Practice E 527.
D
Grade designations correspond to the respective AISI and SAE designations. Grade compositions correspond to the respective AISI compositions.
E
Where minimum and maximum sulfur contents are shown, it is indicative of resulfurized steel.
F
Silicon may be specified by the purchaser as 0.10 % maximum. The need for 0.10 % maximum generally relates to severely cold-formed parts.
G
These steels can be expected to contain 0.0005 to 0.003 % boron. If the usual titanium additive is not permitted, the steels can be expected to contain up to 0.005 %
boron.

6.2 The composition of the steel furnished under this 8. Certification and Test Reports
specification may be other than listed in Table 1 when agreed 8.1 When specified by the purchaser, a manufacturer’s
upon between the manufacturer and the purchaser as out-lined certification that the material was manufactured and tested in
in Specification A 29/A 29M (Table on Heat Analysis Chemi- accordance with this specification, together with a report of the
cal Ranges and Limits of Alloy Steel Bars). cast or heat analysis test results for the specified elements, shall
7. Workmanship, Finish, and Appearance be furnished. The report shall include the name of the manu-
facturer, ASTM designation and year date and revision letter, if
7.1 Workmanship—The bars shall be free of pipe, cracks, any, type and grade, heat number, and size.
and flakes. Within the limits of good manufacturing and
8.2 When Supplementary Requirements are specified, the
inspection practices, the bars shall be free of injurious seams,
report shall include a statement of compliance with the
laps, segregation, or other imperfections which due to their
requirement of the results of tests when the requirement
nature, degree, or extent, will interfere with the use of the
involves measured test values.
material in machining or fabrication of suitable parts.
7.2 Descaling—When descaled bars are required, Supple-
mentary Requirement S12 on Pickling or S13 on Cleaning 9. Keywords
must be specified. 9.1 alloy steel bars; hot-wrought steel bars; steel bars

SUPPLEMENTARY REQUIREMENTS

One or more of the following Supplementary Requirements shall apply when specified by the
purchaser.

S1. Axle Shaft Quality S3. Cold Shearing Quality

S1.1 Axle shaft quality applies to hot-rolled steel bars S3.1 When the bar size exceeds certain limits, it is recom-
intended for the manufacture of power-driven axle shafts of the mended that cold shearing quality steel be ordered. This quality
automotive or truck type, which by their design or method of will provide characteristics which permit cold shearing without
manufacture are not machined all over or have less than cracking. The producer should be consulted in establishing the
recommended stock removed for the proper clean-up of normal proper practice.
surface imperfections.
S4. Cold Working Quality
S2. Ball and Roller Bearing Quality and Bearing Quality S4.1 This classification encompasses bars subject to severe
S2.1 This quality applies to steel intended for antifriction cold plastic deformation such as, but not limited to, upsetting,
bearings. heading, forging, forward or backward extrusion.

3
 A 322 – 07
S4.2 If the type of steel or chemical composition does not S9. Grain Size (Coarse)
have adequate cold working characteristics, appropriate ther- S9.1 The steel shall conform to the coarse austenitic grain
mal treatments should be specified. size requirement of Specification A 29/A 29M.
S4.3 When Supplementary Requirement S1 is specified, the
bars shall be produced by manufacturing practices and sub- S10. Grain Size (Fine)
jected to mill tests and inspection and freedom from injurious S10.1 The steel shall be killed and shall have austenitic
surface imperfections to the extent that the bars shall be grain size of 5 and finer (fine grain), to be determined in
suitable for the manufacture of identified parts. The quality accordance with the comparison procedure in Test Methods
requirements of individual application vary. E 112. The grain structure shall be considered satisfactory
when a minimum of the rated grains are 70 % within the
S5. Aircraft Quality or Magnaflux Quality specified size limits.
S5.1 These quality designations apply to alloy steels for
important or highly stressed parts of aircraft and for other S11. Special Straightness
similar or corresponding purposes involving additional strin- S11.1 The bars shall be produced with special straightness
gent requirements, such as magnetic particle inspection, addi- (see Specification A 29/A 29M for tolerances).
tional discard, macroetch tests (see Method E 381), and hard-
enability control (see Specification A 304). S12. Pickling
S12.1 The surface of the bars shall be descaled by pickling.
S6. Annealing
S13. Cleaning
S6.1 The steel shall be furnished annealed.
S13.1 The surface of the bars shall be descaled by blast
S7. Spheroidize Annealing cleaning or other mechanical methods.
S7.1 The steel shall be spheroidize annealed. S14. Coating
S14.1 The bars shall be oiled, limed, or phosphate-coated as
S8. Stress Relieving specified by the purchaser. The purchaser shall also specify the
S8.1 The steel shall be stress relieved by heating to a method of cleaning (Supplementary Requirement S12 or S13);
temperature specified by the purchaser or to a temperature otherwise, the bars shall be descaled by pickling or blasting at
selected by the manufacturer. the manufacturer’s option.

SUMMARY OF CHANGES

Committee A01 has identified the location of selected changes to this standard since the last issue (A 322 – 06)
that may impact the use of this standard. (Approved May 1, 2007.)

(1) Updated Section 5.

ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.

This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.

This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or [email protected] (e-mail); or through the ASTM website
(www.astm.org).