Project Name

PROJECT PROPOSAL OF SMART PHONE BASED

Semester Project Proposal by

Group Members:

BEEM-F18-014 Hamza Mughal

BEEM-F19-015 Muhammad Irfan

BEEM-F18-017 Abdullah Bin Zubair

Advisor: Engr.
Basit ali sb

Signature:

Department of Electrical Engineering

1
ABSTRACT
The main objective of the project is to develop home automation system using arduino board with
Bluetooth being remotely controlled by an android operating system Smartphone. As technology is
advancing so houses are also getting smarter modern houses are gradually shifting from
conventional switches to centralized control system involving remote control switches. Presently
conventional wall switches which is located in different parts of the house makes it difficult for the
user to go near them to operate. Even more it becomes more difficult for the elderly or physically
handicapped people to do so. Remote controlled home automation system provides a most modern
solution with smart phones .In order to achieve this a Bluetooth module is interface to the aurdino
board at the receiver end while on the transmitter end, a GUI application on the cell phone sends
ON OFF command to the receiver where loads are connected.

2
LIST OF ACRONYMS

3
 Table of Contents
ABSTRACT...................................................................................................................2

LIST OF ACRONYMS..................................................................................................3

LIST OF FIGURES........................................................................................................5

LIST OF TABLES.........................................................................................................6

INTRODUCTION......................................................................................................7
PROJECT STATEMENT…………………………………………………………....7
ROJECT OVERIEW/GOAL......................................................................................8
PROJECT METHODLOGY......................................................................................8
PROJECT MILESTONES AND DELIVERABLES.................................................9
WORK DIVISION...................................................................................................10
REFERENCES.........................................................................................................11

4
LIST OF FIGURES

5
LIST OF TABLES

6
INTRODUCTION:
Nowadays, we have remote controls for our television sets and other electronic systems, which
have made our lives real easy. Have you ever wondered about home automation which would
give the facility of controlling tube lights, fans and other electrical appliances at home using a
remote control? Off-course, Yes! But, are the available options cost-effective? If the answer is
No, we have found a solution to it. We have come up with a new system called Arduino based
home automation using Bluetooth. This system is super-cost effective and can give the user, the
ability to control any electronic device without even spending for a remote control. This project
helps the user to control all the electronic devices using his/her smartphone. Time is a very
valuable thing. Everybody wants to save time as much as they can. New technologies are being
introduced to save our time. To save people’s time we are introducing Home Automation system
using Bluetooth . With the help of this system you can control your home appliances from your
mobile phone. You can turn on/off your home appliances within the range of Bluetooth.

7
PROJECT OVERIEW/GOAL
The aim of the project is to design and construct a home automation system that will remotely
switch on or off any household appliances connected to it, using a microcontroller, voice dial on
phone, or Bluetooth based android application. Project Objective The objective of this project is
to implement a low cost , reliable and scalable home automation system that can be used to
remotely switch on or off any household appliance , using a microcontroller to achieve hardware
simplicity ,low cost short messaging service for feedback and voice dial from any phone to
toggle the switch state. Project scope and limitation This project work is complete on its own in
remotely and automatically switching on or off of an electrical appliance not limited to
household appliances and sends a feedback message indicating the new present state of the
appliance.

PROJECT STATEMENT:

The list of components mentioned here are specifically for controlling 4 different loads.

 Arduino Uno with Atmega 328P microcontroller

 HC – 05 Bluetooth Module

 10 KΩ Resistor

 1 KΩ Resistor X 4

 BC547 NPN Transistor X 4

 1N4007 Diode X 4

 5 V Relay X 4

 Prototyping board (Bread board)

 Connecting wires

 9 V Power supply

 Smartphone or tablet (Bluetooth enabled) Software Requirement

 Arduino 1.6.9 compiler  Proteus 7  Android application

PROJECT METIHODLOGY

8
BLOCK DIAGRAM

PROJECT MILESTONES AND DELIVERABLES

This project is one of the important Arduino Projects. Arduino based home automation
using Bluetooth project helps the user to control any electronic device using Device
Control app on their Android Smartphone. The android app sends commands to the
controller – Arduino, through wireless communication, namely, Bluetooth. The Arduino is
connected to the main PCB which has five relays as shown in the block diagram. These
relays can be connected to different electronic devices. As per the block diagram, Device 1
– Buzzer, Device 2- Fan, Device 3 – Lights. When the user presses on the ‘On’ button
displayed on the app for the device 1, the Buzzer is switched on. This Buzzer can be
switched off, by pressing the same button again. Similarly, when the user presses on the
‘On’ button displayed on the app for the device 2, the fan is switched on. The fan can be
switched off, by pressing the same button again. This project of home automation using
Bluetooth and Arduino can be used for controlling any AC or DC devices. In the

9
demonstration, we have used DC Fan and DC Bulb. To drive this DC Fan and Light, a 9V
battery is connected.

PROJECT APPLICATIONS:

The purpose of the system is to use mobile phone’s inbuilt Bluetooth facility for
automation. Different hardware

and software unit of the system are described. The complete application software has been
designed using

Android, using C Language. The HAS furnishes a good paradigm for any Automation
System based on Android Mobile Phone and Bluetooth.

PROJECT DELIVERABLES

PROJECT MILESTONES

Table 1: Project Milestones

OBJECTIVES EXPECTED TIME-LINE

Proposal submission October 2020

Proposal defense November 2020

Project Evaluation I December 2020

Project Evaluation II December 2020

ORKDIVISION

Table 2. Work Division

Sr. # Name Allocated Tasks

10
1 Hamza Mughal

2 Muhammad Irfan

3 Abdullah Bin Zubair

11
REFERENCES

[1] www.autogates.com.my

[2] www.usautomatic.com

[3] www.amazinggates.com

[4] www.microchip.co.uk

[5] www.quora.com

[6] www.engineeringproject.com

[7] www.efy.com

[8] www.electronicsworldforyou.com

12