Most Widely Accepted and Trusted

ESR-2361
ICC-ES Evaluation Report Reissued 05/2017
Revised 01/2019
ICC-ES
000| (800) 423-6587 | (562) 699-0543 | www.icc-es.org This report is subject to renewal 05/2019.

DIVISION: 05 00 00—METALS
SECTION: 05 40 00—COLD-FORMED METAL FRAMING
SECTION: 05 41 00—STRUCTURAL METAL STUD FRAMING
DIVISION: 09 00 00—FINISHES
SECTION: 09 22 16.13—NON-STRUCTURAL METAL STUD FRAMING

REPORT HOLDER:

FRAMECAD LICENSING LTD.

EVALUATION SUBJECT:

COLD-FORMED STEEL FRAMING MEMBERS

“2014 Recipient of Prestigious Western States Seismic Policy Council

(WSSPC) Award in Excellence” A Subsidiary of

ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically
addressed, nor are they to be construed as an endorsement of the subject of the report or a recommendation for its use.
There is no warranty by ICC Evaluation Service, LLC, express or implied, as to any finding or other matter in this
report, or as to any product covered by the report.

Copyright © 2019 ICC Evaluation Service, LLC. All rights reserved.

ICC-ES Evaluation Report ESR-2361
Reissued May 2017
Revised January 2019
This report is subject to renewal May 2019.

www.icc-es.org | (800) 423-6587 | (562) 699-0543 A Subsidiary of the International Code Council ®

DIVISION: 05 00 00—METALS 2.0 USES

Section: 05 40 00—Cold-Formed Metal Framing
The FRAMECAD Licensing Ltd. steel framing members
Section: 05 41 00—Structural Metal Stud Framing
(C-shapes and tracks) are recognized for use in interior
and exterior, nonload-bearing and load-bearing
DIVISION: 09 00 00—FINISHES
applications.
Section: 09 22 16.13—Non-Structural Metal Stud
Framing 3.0 DESCRIPTION
3.1 General:
REPORT HOLDER: The products that are recognized in this report are limited
to those products noted in Tables 3 and 4. The C-shapes
FRAMECAD LICENSING LTD. and tracks are factory-formed from coils of light gage steel.
See Table 14 for manufacturing locations. See Figures 1
ADDITIONAL LISTEES: and 2 for C-shape and track configurations, and Tables 1
through 4 for steel minimum yield strengths, steel
FRAMECAD LTD. thicknesses, and dimensional details. The C-shapes are
manufactured with and without web punch-outs. When
DOUGLASS COLONY GROUP, INC. punch-outs are provided, they are located along the center
1
of the web, with a maximum width of 1 /2 inches (38 mm)
GEORGE M. RAYMOND CO. and a maximum length of 4 inches (102 mm). The punch-
outs are spaced a minimum of 24 inches (610 mm) on
VOLSTRUKT, LLC center. The edge of the punch-outs must be a minimum of
10 inches (254 mm) from each end of the stud. The tracks
CENTERLINE PREFAB, LLC have the same shape as the C-shapes, except the stiffener
lip of the track is removed at the location of each stud.
BLUVERA, LLC Gross, effective, and torsional section properties are set
forth in Tables 3 and 4.
C.J. COAKLEY CO., INC.
3.2 Material:
F.L. CRANE AND SONS, INC. The C-shapes and tracks are formed from galvanized steel
coils. The steel complies with ASTM A653 SS Grade 33,
NETWORK FRAMING SOLUTIONS, LLC ASTM A1003 Structural Grade 33 Type H (ST33H) or
ASTM A1003 Nonstructural Grade 33 (NS33) [for
FRAMELAND INDUSTRIES, LLC nonload-bearing studs with a 10 psf (478 Pa) maximum
transverse load only]; except for 0.0538-inch-thick [54 mils
EVALUATION SUBJECT: (1.366 mm)] and greater C-shapes and tracks, which are
formed from steel complying with ASTM A653 SS Grade
COLD-FORMED STEEL FRAMING MEMBERS 50, Class 1 or 3, or ASTM A1003 Structural Grade 50 Type
1.0 EVALUATION SCOPE H (ST50H). The steel is hot-dipped galvanized with a
minimum G60 or G40 galvanized coating designation.
Compliance with the following codes: Members with less than a G60 galvanized coating are
limited to interior nonload-bearing wall applications with
 2015, 2012 and 2009 International Building Code® (IBC)
10 psf (478 Pa) maximum transverse load.
 2015, 2012 and 2009 International Residential Code® 4.0 DESIGN AND INSTALLATION
(IRC)
4.1 Design:
†
 2013 Abu Dhabi International Building Code (ADIBC) Structural capacities are determined in accordance with
†
The ADIBC is based on the 2009 IBC. 2009 IBC code sections referenced the applicable edition of the North American Specification
in this report are the same sections in the ADIBC. for the Design of Cold-Formed Steel Structural Members
Property evaluated: (AISI-S100) based on structural properties in Tables 1
through 4 of this report. Web crippling details and
Structural maximum web crippling loads are described in Tables 5

ICC-ES Evaluation Reports are not to be construed as representing aesthetics or any other attributes not specifically addressed, nor are they to be construed
as an endorsement of the subject of the report or a recommendation for its use. There is no warranty by ICC Evaluation Service, LLC, express or implied, as
to any finding or other matter in this report, or as to any product covered by the report.

Copyright © 2019 ICC Evaluation Service, LLC. All rights reserved. Page 1 of 20
ESR-2361 | Most Widely Accepted and Trusted Page 2 of 20

and 6. As an alternative, structural uses may be 7.0 IDENTIFICATION

determined in accordance with Section 4.1.1 or 4.1.2. 7.1 Each C-shape and track must have a legible label,
C-shapes listed in Table 13 and tracks with a thickness stamp or embossment, at a maximum of 48 inches
greater than 27 mils qualify for use with the prescriptive (1219 mm) on center, indicating the manufacturer’s
requirements of the 2009 IRC. For use under the IRC of all name (see Report Holder or Additional Listees at
other sections, the cold-formed steel framing members beginning of this report) or initials; the evaluation
must be limited to engineered structures, in accordance report number (ESR-2361); the acronym “ICC-ES”;
with IRC Section R301.1.3. material minimum base-metal thickness (uncoated) in
4.1.1 Nonload-bearing Wall Heights: decimal thickness or mils; minimum specified yield
strength [if greater than 33 ksi (228 MPa)]; and
Allowable wall heights for interior nonload-bearing walls coating grade (if G60 or greater). Members with a
are shown in Table 7. The allowable end reactions of the coating grade of less than G60 must have “NS” noted
studs based on web crippling effects for the applicable on the member.
bearing lengths in Tables 5 and 6 must equal, or exceed,
the applied load end reaction. 7.2 The report holder’s contact information is the
4.1.2 Load-bearing Wall Studs: following:
Allowable axial loads combined with transverse loads for FRAMECAD LICENSING LTD.
POST OFFICE BOX 1292
various heights and stud spacings, based on mechanical
AUCKLAND 1140
bracing at a maximum of 48 inches (1219 mm) on center NEW ZEALAND
and sheathing on both sides of the studs for lateral 64 9 307 0411
stability, with the design complying with Section C5 in www.framecad.com
AISI-S100, are shown in Tables 8 through 12. The
allowable end reactions of the studs based on web 7.3 The additional listee’s contact information is the
crippling effects for the applicable bearing lengths in following:
Tables 5 and 6 must equal, or exceed, the end reactions FRAMECAD LTD.
based on the applied transverse loads. 99 FELTON MATHEW AVENUE
GLEN INNES/ST. JOHN,
4.2 Installation: AUCKLAND 1072
The C-shapes and tracks must be installed in accordance NEW ZEALAND
with the approved plans and this report. If there is a conflict www.framecad.com
between the plans submitted for approval and this report, DOUGLASS COLONY GROUP, INC.
this report governs. The approved plans must be available 5901 EAST 58TH AVENUE
at the jobsite at all times during installation. COMMERCE CITY, COLORADO 80022
www.douglasscolony.com
5.0 CONDITIONS OF USE
GEORGE M. RAYMOND CO.
The FRAMECAD Licensing Ltd. steel framing members 6345 SOUTH VALLEY VIEW BOULEVARD,
described in this report comply with, or are suitable SUITE H
alternatives to what is specified in, those codes listed in LAS VEGAS, NEVADA 89118
Section 1.0 of this report, subject to the following www.raymondgroup.com
conditions: VOLSTRUKT, LLC
5.1 C-shapes and tracks must be installed in accordance 13802 TURBINE DRIVE
AUSTIN, TEXAS 78728
with this report, the applicable code and the approved
www.volstrukt.com
plans. If there is a conflict between this report and the
CENTERLINE PREFAB, LLC
submitted plans, this report governs.
4101 ROGER B CHAFFEE BOULEVARD SE
5.2 Minimum base steel thickness of cold-formed steel GRAND RAPIDS, MICHIGAN 49548
members, as delivered to the jobsite, must be at least www.centerlineprefab.com
95 percent of the design thickness specified in Tables BLUVERA, LLC
2 through 4. 103 ENTERPRISE DRIVE
5.3 Complete plans and calculations verifying compliance NORTHWOOD, IOWA 50459
with this report must be submitted to the code official C. J. COAKLEY CO., INC.
for each project. The calculations and drawings must 2719-C DORR AVENUE
MERRIFIELD, VIRGINIA 22031
be prepared and sealed by a registered design
www.cjcoakley.com
professional where required by the statutes of the
jurisdiction in which the project is constructed. F.L. CRANE AND SONS, INC.
5707 GULF TECH DRIVE
5.4 Stud member end reactions, resulting from allowable OCEAN SPRINGS, MISSISSIPPI 39564
heights and loads, as noted in the accompanying www.flcrane.com
tables, must be checked with the web crippling tables NETWORK FRAMING SOLUTIONS, LLC
noted in this report. ST
35B ROBERT JACKSON WAY, 1 FLOOR
5.5 C-shapes and tracks having a galvanized coating PLAINVILLE, CONNECTICUT 06062
www.network-interiors.com
weight of less than G60 must be limited to use as
nonload-bearing interior wall framing subject to a FRAMELAND INDUSTRIES, LLC
maximum transverse load of 10 psf (478 Pa). 2508 PETERSON ROAD
APOPKA, FLORIDA 32703
6.0 EVIDENCE SUBMITTED www.frameland-industries.com
Data in accordance with the ICC-ES Acceptance Criteria
for Cold-formed Steel Framing Members (AC46), dated
June 2012 (editorially revised April 2015).
ESR-2361 | Most Widely Accepted and Trusted Page 3 of 20
3
TABLE 1—MEMBER DESIGNATION DIMENSIONS

1
MEMBER DEPTH WEB DEPTH FLANGE WIDTH 2
LIP SIZE (in)
(in) (in) (in)

5
1 /8 1.625 1.625 0.50
1
2 /2 2.500 1.625 0.50
1
3 /2 3.500 1.625 0.50
5
3 /8 3.625 1.625 0.50
4 4.000 1.625 0.50
1
5 /2 5.500 1.625 0.50
6 6.000 1.626 0.50
For SI: 1 inch = 25.4 mm.
1
Web depth for both stud and track sections is measured from outside of flange to outside of flange.
2
Track flange stiffeners (lips) are removed at stud locations.
3
Member Designation identification provides nominal dimensions as shown in the example below:
Example: 600S162-43; 600 = 6 inch depth (Depth measured from the outside face to outside face of flanges),
S = C-Section, 162 = 1.625 inch flange width, 43 = thickness designation of 43 mils or 0.0428 inches.

TABLE 2—UNCOATED STEEL THICKNESS

THICKNESS DESIGNATION DESIGN THICKNESS MINIMUM THICKNESS INSIDE BEND

(mils) (in) (in) RADIUS (in)

27 0.0283 0.0269 0.0796

30 0.0312 0.0296 0.0781
33 0.0346 0.0329 0.0764
43 0.0451 0.0428 0.0712
54 0.0566 0.0538 0.0849
68 0.0713 0.0677 0.1069
For SI: 1 inch = 25.4 mm.
Notes for Section Properties Tables (Tables 3 and 4):
1. For applications in accordance with the IRC, use of all 162S162-XX, 250S162-XX, 350S162-27, 350S162-30, 362S162-27, 362S162-30; and
162T162-XX, 250T162-XX, 350T162-27, 350T162-27, 350T162-30, 362T162-27, and 362T162-30 are applicable only for engineered
designs in accordance with IRC Section R301.1.3.
2. When provided, factory punch-outs must be located along the centerline of the webs of the members, have a minimum center-to-center
spacing of 24”, a maximum width of half the member depth or 11/2”, whichever is less, and a maximum length of 4”. The minimum distance
between the end of the member and the near edge of the web punch-out must be no less than 10”.
3. The strength increase due to cold work of forming was incorporated for flexural strength as applicable in accordance with Section A7.2 of
AISI-S100.
4. Minimum base metal thickness must be 95% of the design thickness in accordance with Section A2.4 of AISI-S100.
5. Tabulated gross properties, including torsional properties, are based on the full unreduced cross section of the studs, away from the punch-
outs.
6. For deflection calculations, use the effective moment of inertia.
7. Allowable moment is the lesser of Ma and Mad. Distortional buckling moment, Mad, based on assumed Kφ = 0
8. Studs are assumed to be adequately braced at a maximum spacing of Lu to develop full allowable moment, Ma.
9. Definitions of structural property symbols:
Gross Properties
Area: The cross sectional area of the full unreduced cross-section of the studs, away from the punch-outs.
Weight: The weight per foot of the full unreduced cross-section of the studs, away from the punch-outs.
Ix: Moment of inertia of the gross section about the strong axis (X-X).
Rx: Radius of gyration of the gross section about the X-X axis.
Sx: Gross section-modulus about the strong axis (X-X).
Iy: Moment of inertia of the gross section about the weak axis (Y-Y).
Ry: Radius of gyration of the gross section about the Y-Y axis.
Effective Properties
Ix: Effective moment of inertia about the strong axis (X-X)..
Sx: Effective section modulus about the strong axis (X-X) at stress = Fy.
Ma: Allowable bending moment based on local buckling.
Mad: Allowable distortional bending moment based on kΦ = 0.
Va: Allowable strong axis shear away from punchout.
Va(net): Allowable strong axis shear at punchout,
Torsional and Other Properties
J: St. Venant Torsional Constant
Cw: Torsional warping constant.
m: Distance from shear center to mid-plane of web.
Xo: Distance from the shear center to the centroid along the principal X-axis.
Ro: Polar radius of gyration about the centroidal principal axis.
β: 1 – (Xo/Ro)2
Lu: Critical unbraced length for lateral-torsional buckling. Members are considered fully braced when unbraced length is less than Lu.
 ESR-2361 | Most Widely Accepted and Trusted Page 4 of 20

2
TABLE 3—C-SHAPE (S) SECTION PROPERTIES

Design Gross Properties Effective Properties Torsional Properties

Member Fy
Thickness Area Weight Ix Sx Rx Iy Ry Ix Sx Ma Mad Vag Va(net) J x 1000 Cw X0 m R0 β Lu
Designation
(in) (ksi) 2
(in ) (lb/ft) 4
(in ) 3
(in ) (in) 3
(in ) (in) 4
(in ) 3
(in ) (in-k) (in-k) (lb) (lb) 4
(in ) 6
(in ) (in) (in) (in) (in)
1
162S162-27 0.0283 33 0.159 0.539 0.073 0.090 0.680 0.061 0.622 0.073 0.078 1.549 1.704 494 106 0.042 0.061 -1.634 0.925 1.876 0.241 46.5
1
162S162-27 0.0283 50 0.159 0.539 0.073 0.090 0.680 0.061 0.622 0.070 0.072 2.146 2.268 748 161 0.042 0.061 -1.634 0.925 1.876 0.241 37.9
162S162-301 0.0312 33 0.174 0.593 0.080 0.099 0.678 0.067 0.620 0.080 0.089 1.768 1.922 543 106 0.057 0.067 -1.631 0.923 1.872 0.241 46.3
1
162S162-30 0.0312 50 0.174 0.593 0.080 0.099 0.678 0.067 0.620 0.079 0.082 2.444 2.573 823 160 0.057 0.067 -1.631 0.923 1.872 0.241 37.8
1
162S162-33 0.0346 33 0.193 0.657 0.088 0.109 0.677 0.074 0.619 0.088 0.102 2.012 2.150 601 105 0.077 0.073 -1.627 0.921 1.868 0.241 46.3
162S162-331 0.0346 50 0.193 0.657 0.088 0.109 0.677 0.074 0.619 0.088 0.092 2.740 2.935 910 159 0.077 0.073 -1.627 0.921 1.868 0.241 37.6
1
162S162-43 0.0451 33 0.250 0.849 0.113 0.139 0.673 0.094 0.615 0.113 0.137 2.968 3.022 777 102 0.169 0.092 -1.615 0.914 1.854 0.242 43.9
1
162S162-43 0.0451 50 0.250 0.849 0.113 0.139 0.673 0.094 0.615 0.113 0.123 3.672 4.075 1177 155 0.169 0.092 -1.615 0.914 1.854 0.242 37.4
1
250S162-27 0.0283 33 0.183 0.624 0.194 0.155 1.029 0.072 0.627 0.193 0.140 2.768 2.756 685 344 0.049 0.122 -1.477 0.863 1.906 0.400 43.4
250S162-271 0.0283 50 0.183 0.624 0.194 0.155 1.029 0.072 0.627 0.188 0.130 3.889 3.630 843 423 0.049 0.122 -1.477 0.863 1.906 0.400 35.6
1
250S162-30 0.0312 33 0.202 0.686 0.213 0.171 1.028 0.079 0.626 0.213 0.159 3.140 3.125 832 378 0.065 0.133 -1.473 0.861 1.902 0.400 43.6
1
250S162-30 0.0312 50 0.202 0.686 0.213 0.171 1.028 0.079 0.626 0.210 0.147 4.409 4.135 1024 466 0.065 0.133 -1.473 0.861 1.902 0.400 35.5
1
250S162-33 0.0346 33 0.223 0.760 0.235 0.188 1.027 0.087 0.624 0.235 0.180 3.553 3.563 975 399 0.089 0.146 -1.470 0.859 1.898 0.401 44.1

250S162-331 0.0346 50 0.223 0.760 0.235 0.188 1.027 0.087 0.624 0.235 0.164 4.909 4.741 1260 515 0.089 0.146 -1.470 0.859 1.898 0.401 35.4
1
250S162-43 0.0451 33 0.289 0.984 0.302 0.242 1.022 0.111 0.620 0.302 0.240 5.224 5.252 1265 394 0.196 0.184 -1.457 0.852 1.885 0.402 42.1
1
250S162-43 0.0451 50 0.289 0.984 0.302 0.242 1.022 0.111 0.620 0.302 0.217 6.503 6.679 1917 597 0.196 0.184 -1.457 0.852 1.885 0.402 35.2
1
350S162-27 0.0283 33 0.212 0.710 0.418 0.239 1.407 0.081 0.620 0.419 0.195 3.860 4.070 614 359 0.057 0.230 -1.331 0.800 2.034 0.571 42.6
350S162-271 0.0283 50 0.212 0.710 0.418 0.239 1.407 0.081 0.620 0.419 0.195 3.860 4.070 614 359 0.057 0.230 -1.331 0.800 2.034 0.571 34.6
1
350S162-30 0.0312 33 0.239 0.793 0.460 0.263 1.406 0.082 0.618 0.460 0.225 4.442 4.559 824 436 0.076 0.252 -1.328 0.798 2.03 0.572 42.8
1
350S162-30 0.0312 50 0.239 0.793 0.460 0.263 1.406 0.082 0.618 0.456 0.201 6.012 5.983 824 436 0.076 0.252 -1.328 0.798 2.03 0.572 34.8
350S162-33 0.0346 33 0.258 0.880 0.508 0.291 1.404 0.098 0.617 0.508 0.257 5.090 5.220 1024 487 0.103 0.277 -1.324 0.796 2.026 0.573 42.7
350S162-33 0.0346 50 0.258 0.880 0.508 0.291 1.404 0.098 0.617 0.508 0.227 6.780 6.880 1125 535 0.103 0.277 -1.324 0.796 2.026 0.573 34.5
350S162-43 0.0451 33 0.334 1.140 0.655 0.374 1.400 0.125 0.612 0.654 0.357 7.050 7.310 1739 631 0.227 0.350 -1.312 0.789 2.014 0.575 42.6

350S162-43 0.0451 50 0.334 1.140 0.655 0.374 1.400 0.125 0.612 0.654 0.309 9.250 9.800 2141 777 0.227 0.350 -1.312 0.789 2.014 0.575 34.2

350S162-54 0.0566 33 0.415 1.410 0.805 0.460 1.393 0.152 0.606 0.804 0.447 8.830 9.080 2253 633 0.443 0.426 -1.298 0.782 1.998 0.578 42.7

350S162-54 0.0566 50 0.415 1.410 0.805 0.460 1.393 0.152 0.606 0.804 0.426 12.740 13.050 3372 947 0.443 0.426 -1.298 0.782 1.998 0.578 34.5

350S162-68 0.0713 33 0.515 1.750 0.985 0.563 1.383 0.184 0.597 0.985 0.551 12.570 12.830 2774 592 0.872 0.514 -1.280 0.772 1.977 0.581 39.7

350S162-68 0.0713 50 0.515 1.750 0.985 0.563 1.383 0.184 0.597 0.985 0.549 16.440 16.850 4203 897 0.872 0.514 -1.280 0.772 1.977 0.581 34.5
 ESR-2361 | Most Widely Accepted and Trusted Page 5 of 20

2
TABLE 3—C-SHAPE (S) SECTION PROPERTIES (Continued)

Design Gross Properties Effective Properties Torsional Properties

Member Fy
Thickness Area Weight Ix Sx Rx Iy Ry Ix Sx Ma Mad Vag Va(net) J x 1000 Cw X0 m R0 β Lu
Designation
2 4 3 3 4 3 4 6
(in) (ksi) (in ) (lb/ft) (in ) (in ) (in) (in ) (in) (in ) (in ) (in-k) (in-k) (lb) (lb) (in ) (in ) (in) (in) (in) (in)
1
362S162-27 0.0283 33 0.216 0.730 0.455 0.251 1.454 0.083 0.619 0.445 0.202 3.998 4.178 589 372 0.058 0.247 -1.316 0.793 2.056 0.590 42.7
1
362S162-27 0.0283 50 0.216 0.730 0.455 0.251 1.454 0.083 0.619 0.445 0.180 5.374 5.456 589 372 0.058 0.247 -1.316 0.793 2.056 0.590 34.5
1
362S162-30 0.0312 33 0.237 0.806 0.499 0.275 1.452 0.090 0.617 0.499 0.234 4.619 4.740 794 449 0.077 0.270 -1.312 0.791 0.038 0.591 42.6

362S162-301 0.0312 50 0.237 0.806 0.499 0.275 1.452 0.090 0.617 0.495 0.209 6.247 6.217 794 449 0.077 0.270 -1.312 0.791 0.038 0.591 34.5

362S162-33 0.0346 33 0.262 0.890 0.551 0.304 1.450 0.099 0.616 0.551 0.268 5.290 5.430 1024 521 0.105 0.297 -1.308 0.789 2.048 0.592 42.6

362S162-33 0.0346 50 0.262 0.890 0.551 0.304 1.450 0.099 0.616 0.551 0.236 7.180 7.170 1080 553 0.105 0.297 -1.308 0.789 2.048 0.592 34.4

362S162-43 0.0451 33 0.340 1.160 0.710 0.392 1.445 0.127 0.611 0.710 0.372 7.340 7.620 1739 676 0.230 0.376 -1.297 0.782 2.036 0.594 42.5

362S162-43 0.0451 50 0.340 1.160 0.710 0.392 1.445 0.127 0.611 0.710 0.321 9.620 10.200 2141 832 0.230 0.376 -1.297 0.782 2.036 0.594 34.2

362S162-54 0.0566 33 0.422 1.440 0.873 0.482 1.438 0.154 0.605 0.873 0.467 9.220 9.520 2341 705 0.451 0.457 -1.283 0.774 2.02 0.597 42.5

362S162-54 0.0566 50 0.422 1.440 0.873 0.482 1.438 0.154 0.605 0.873 0.444 13.280 13.600 3372 1016 0.451 0.457 -1.283 0.774 2.02 0.597 34.4

362S162-68 0.0713 33 0.524 1.780 1.069 0.590 1.429 0.186 0.596 1.069 0.579 11.430 11.650 2884 662 0.887 0.552 -1.264 0.765 1.999 0.600 42.7

362S162-68 0.0713 50 0.524 1.780 1.069 0.590 1.429 0.186 0.596 1.069 0.574 17.190 17.660 4370 1004 0.887 0.552 -1.264 0.765 1.999 0.600 34.3

400S162-33 0.0346 33 0.275 0.940 0.692 0.346 1.586 0.103 0.611 0.692 0.299 5.910 6.070 976 595 0.110 0.363 -1.263 0.768 2.118 0.644 42.3

400S162-33 0.0346 50 0.275 0.940 0.692 0.346 1.586 0.103 0.611 0.692 0.299 5.910 6.070 976 595 0.110 0.363 -1.263 0.768 2.118 0.644 34.2

400S162-43 0.0451 33 0.357 1.210 0.892 0.446 1.581 0.131 0.606 0.892 0.417 8.230 8.550 1739 810 0.242 0.460 -1.252 0.761 2.106 0.647 42.2

400S162-43 0.0451 50 0.357 1.210 0.892 0.446 1.581 0.131 0.606 0.892 0.359 10.750 11.400 2141 997 0.242 0.460 -1.252 0.761 2.106 0.647 34.0

400S162-54 0.0566 33 0.443 1.510 1.098 0.549 1.574 0.159 0.600 1.098 0.526 10.390 10.850 2603 944 0.473 0.560 -1.238 0.754 2.09 0.649 42.2

400S162-54 0.0566 50 0.443 1.510 1.098 0.549 1.574 0.159 0.600 1.098 0.498 14.900 15.250 3372 1223 0.473 0.560 -1.238 0.754 2.09 0.649 34.1

400S162-68 0.0713 33 0.550 1.870 1.346 0.673 1.564 0.192 0.591 1.346 0.658 13.000 13.300 3215 895 0.933 0.677 -1.220 0.745 2.069 0.653 42.2

400S162-68 0.0713 50 0.550 1.870 1.346 0.673 1.564 0.192 0.591 1.346 0.648 19.410 20.160 4871 1356 0.933 0.677 -1.220 0.745 2.069 0.653 34.0

550S162-33 0.0346 33 0.327 1.110 1.459 0.530 2.112 0.113 0.589 1.459 0.512 10.110 8.630 699 699 0.130 0.713 -1.114 0.697 2.459 0.795 41.4

550S162-33 0.0346 50 0.327 1.110 1.459 0.530 2.112 0.113 0.589 1.459 0.444 13.280 11.260 697 697 0.130 0.713 -1.114 0.697 2.459 0.795 33.5

550S162-43 0.0451 33 0.424 1.440 1.884 0.685 2.107 0.145 0.584 1.883 0.681 14.800 13.140 1550 1199 0.288 0.905 -1.103 0.691 2.449 0.797 39.2

550S162-43 0.0451 50 0.424 1.440 1.884 0.685 2.107 0.145 0.584 1.883 0.624 18.690 16.240 1550 1199 0.288 0.905 -1.103 0.691 2.449 0.797 33.4

550S162-54 0.0566 33 0.528 1.800 2.325 0.845 2.098 0.176 0.577 2.324 0.845 18.760 17.880 2739 1666 0.564 1.105 -1.090 0.684 2.434 0.800 38.7

550S162-54 0.0566 50 0.528 1.800 2.325 0.845 2.098 0.176 0.577 2.324 0.811 26.860 23.530 3093 1881 0.564 1.105 -1.090 0.684 2.434 0.800 31.6

550S162-68 0.0713 33 0.657 2.240 2.862 1.041 2.087 0.212 0.569 2.861 1.041 23.720 23.730 4347 2057 1.114 1.342 -1.072 0.675 2.414 0.803 38.0

550S162-68 0.0713 50 0.657 2.240 2.862 1.041 2.087 0.212 0.569 2.861 1.031 34.950 32.300 5350 2532 1.114 1.342 -1.072 0.675 2.414 0.803 31.1
 ESR-2361 | Most Widely Accepted and Trusted Page 6 of 20

2
TABLE 3—C-SHAPE (S) SECTION PROPERTIES (Continued)

Design Gross Properties Effective Properties Torsional Properties

Member Fy
Thickness Area Weight Ix Sx Rx Iy Ry Ix Sx Ma Mad Vag Va(net) J x 1000 Cw X0 m R0 β Lu
Designation
(in) (ksi) (in2) (lb/ft) (in4) (in3) (in) (in3) (in) (in4) (in3) (in-k) (in-k) (lb) (lb) (in4) (in6) (in) (in) (in) (in)

600S162-33 0.0346 33 0.344 1.170 1.793 0.598 2.282 0.116 0.581 1.793 0.577 11.410 9.470 638 638 0.137 0.861 -1.072 0.677 2.588 0.828 41.1

600S162-33 0.0346 50 0.344 1.170 1.793 0.598 2.282 0.116 0.581 1.793 0.482 14.427 12.319 637 637 0.137 0.861 -1.072 0.677 2.588 0.828 33.3

600S162-43 0.0451 33 0.447 1.520 2.316 0.772 2.277 0.148 0.576 2.316 0.767 16.680 14.470 1416 1240 0.303 1.095 -1.062 0.67 2.577 0.830 39.0

600S162-43 0.0451 50 0.447 1.520 2.316 0.772 2.277 0.148 0.576 2.316 0.706 21.122 17.827 1416 1240 0.303 1.095 -1.062 0.67 2.577 0.830 33.1

600S162-54 0.0566 33 0.556 1.890 2.861 0.954 2.268 0.180 0.570 2.860 0.953 21.170 19.760 2739 1890 0.594 1.337 -1.049 0.663 2.563 0.833 38.4

600S162-54 0.0566 50 0.556 1.890 2.861 0.954 2.268 0.180 0.570 2.860 0.916 30.330 25.910 2823 1947 0.594 1.337 -1.049 0.663 2.563 0.833 31.4

600S162-68 0.0713 33 0.693 2.360 3.526 1.175 2.256 0.218 0.561 3.525 1.175 26.790 26.790 4347 2339 1.174 1.626 -1.032 0.655 2.543 0.835 37.7

600S162-68 0.0713 50 0.693 2.360 3.526 1.175 2.256 0.218 0.561 3.525 1.164 39.470 35.710 5350 2879 1.174 1.626 -1.032 0.655 2.543 0.835 30.8

For SI: 1 inch = 25.4 mm;1 lb/ft = 14.5939 N/m; 1 in-k = 12.8 N-m; 1 lb = 4.448 N; 1 ksi = 6.89 MPa.
1
For applications in accordance with the IRC, use of all 162S162-XX, 250S162-XX, 350S162-27, 350S162-30, 362S162-27 and 362S162-30 is applicable only for engineered designs in accordance with IRC Section R301.1.3.
2
Member Designation identification provides nominal dimensions as shown in the example below:
Example: 600S162-43; 600 = 6 inch depth (Depth measured from the outside face to outside face of flanges), S = C-Section, 162 = 1.625 inch flange width, 43 = thickness designation of 43 mils or
0.0428 inches.

2
TABLE 4—TRACK (T) SECTION PROPERTIES

Design Gross Properties Effective Properties Torsional Properties

Member Fy
Thickness Area Weight Ix Sx Rx Iy Ry Ix Sx Ma Vag J x 1000 Cw X0 m R0 β
Designation
2 4 3 3 4 3 4 6
(in) (ksi) (in ) (lb/ft) (in ) (in ) (in) (in ) (in) (in ) (in ) (in-k) (lb) (in ) (in ) (in) (in) (in)
1
162T162-27 0.0283 33 0.138 0.469 0.079 0.090 0.757 0.040 0.537 0.057 0.046 0.910 541 0.037 0.022 -1.216 0.683 1.529 0.368
1
162T162-27 0.0283 50 0.138 0.469 0.079 0.090 0.757 0.040 0.537 0.053 0.042 1.268 820 0.037 0.022 -1.216 0.683 1.529 0.368
1
162T162-30 0.0312 33 0.152 0.517 0.087 0.099 0.756 0.044 0.536 0.065 0.053 1.044 597 0.049 0.024 -1.214 0.682 1.528 0.369
1
162T162-30 0.0312 50 0.152 0.517 0.087 0.099 0.756 0.044 0.536 0.060 0.049 1.452 905 0.049 0.024 -1.214 0.682 1.528 0.369
1
162T162-33 0.0346 33 0.169 0.574 0.097 0.109 0.758 0.048 0.536 0.074 0.061 1.211 663 0.067 0.026 -1.212 0.681 1.526 0.369
1
162T162-33 0.0346 50 0.169 0.574 0.097 0.109 0.758 0.048 0.536 0.069 0.056 1.679 1005 0.067 0.026 -1.212 0.681 1.526 0.369
1
162T162-43 0.0451 33 0.219 0.747 0.219 0.142 0.759 0.063 0.534 0.106 0.090 1.780 867 0.149 0.034 -1.206 0.678 1.522 0.372
1
162T162-43 0.0451 50 0.219 0.747 0.219 0.142 0.759 0.063 0.534 0.099 0.082 2.450 1314 0.149 0.034 -1.206 0.678 1.522 0.372
1
250T162-27 0.0283 33 0.163 0.554 0.193 0.146 1.089 0.046 0.530 0.143 0.083 1.633 685 0.043 0.055 -1.086 0.634 1.626 0.554
1
250T162-27 0.0283 50 0.163 0.554 0.193 0.146 1.089 0.046 0.530 0.136 0.077 2.317 833 0.043 0.055 -1.086 0.634 1.626 0.554
1
250T162-30 0.0312 33 0.179 0.610 0.213 0.161 1.089 0.050 0.529 0.162 0.094 1.859 832 0.058 0.060 -1.084 0.634 1.625 0.555
1
250T162-30 0.0312 50 0.179 0.610 0.213 0.161 1.089 0.050 0.529 0.153 0.088 2.628 1024 0.058 0.060 -1.084 0.634 1.625 0.555
 ESR-2361 | Most Widely Accepted and Trusted Page 7 of 20

2
TABLE 4—TRACK (T) SECTION PROPERTIES (Continued)

Design Gross Properties Effective Properties Torsional Properties

Member Fy
Thickness Area Weight Ix Sx Rx Iy Ry Ix Sx Ma Vag J x 1000 Cw X0 m R0 β
Designation
2 4 3 3 4 3 4 6
(in) (ksi) (in ) (lb/ft) (in ) (in ) (in) (in ) (in) (in ) (in ) (in-k) (lb) (in ) (in ) (in) (in) (in)
1
250T162-33 0.0346 33 0.199 0.676 0.235 0.178 1.088 0.056 0.529 0.185 0.108 2.310 1024 0.079 0.067 -1.083 0.633 -1.624 0.555
1
250T162-33 0.0346 50 0.199 0.676 0.235 0.178 1.088 0.056 0.529 0.175 0.100 3.004 1260 0.079 0.067 -1.083 0.633 -1.624 0.555
1
250T162-43 0.0451 33 0.259 0.881 0.308 0.232 1.091 0.072 0.527 0.262 0.156 3.086 1356 0.176 0.087 -1.077 0.630 1.621 0.558
1
250T162-43 0.0451 50 0.259 0.881 0.308 0.232 1.091 0.072 0.527 0.247 0.144 4.315 2054 0.176 0.087 -1.077 0.630 1.621 0.558
1
350T162-27 0.0283 33 0.190 0.650 0.400 0.220 1.447 0.051 0.515 0.307 0.134 2.660 590 0.051 0.117 -0.971 0.586 1.817 0.714
1
350T162-27 0.0283 50 0.190 0.650 0.400 0.220 1.447 0.051 0.515 0.298 0.110 3.302 590 0.051 0.117 -0.971 0.586 1.817 0.714
1
350T162-30 0.0312 33 0.211 0.716 0.441 0.242 1.447 0.056 0.514 0.346 0.152 3.008 790 0.068 0.128 -0.97 0.586 1.816 0.715
1
350T162-30 0.0312 50 0.211 0.716 0.441 0.242 1.447 0.056 0.514 0.334 0.133 4.324 790 0.068 0.128 -0.97 0.586 1.816 0.715
350T162-33 0.0346 33 0.233 0.794 0.490 0.269 1.449 0.062 0.514 0.395 0.175 3.447 1024 0.093 0.142 -0.968 0.585 1.816 0.716
350T162-33 0.0346 50 0.233 0.794 0.490 0.269 1.449 0.062 0.514 0.376 0.164 4.918 1078 0.093 0.142 -0.968 0.585 1.816 0.716
350T162-43 0.0451 33 0.304 1.035 0.641 0.349 1.451 0.080 0.512 0.553 0.248 4.905 1739 0.206 0.185 -0.963 0.582 1.815 0.719
350T162-43 0.0451 50 0.304 1.035 0.641 0.349 1.451 0.080 0.512 0.525 0.232 6.948 2141 0.206 0.185 -0.963 0.582 1.815 0.719
350T162-54 0.0566 33 0.381 1.298 0.811 0.438 1.459 0.989 0.509 0.743 0.341 6.729 2386 0.407 0.234 -0.957 0.578 1.817 0.726
350T162-54 0.0566 50 0.381 1.298 0.811 0.438 1.459 0.989 0.509 0.707 0.317 9.492 3372 0.407 0.234 -0.957 0.578 1.817 0.726
350T162-68 0.0713 33 0.480 1.634 1.026 0.549 1.462 0.123 0.506 0.992 0.467 9.220 3005 0.814 0.294 -0.950 0.574 1.816 0.726
350T162-68 0.0713 50 0.480 1.634 1.026 0.549 1.462 0.123 0.506 0.948 0.433 12.978 4554 0.814 0.294 -0.950 0.574 1.816 0.726
1
362T162-27 0.0283 33 0.195 0.662 0.435 0.230 1.497 0.051 0.513 0.337 0.142 2.803 571 0.052 0.127 -0.958 0.580 1.848 0.731
1
362T162-27 0.0283 50 0.195 0.662 0.435 0.230 1.497 0.051 0.513 0.328 0.116 3.486 571 0.052 0.127 -0.958 0.580 1.848 0.731
1
362T162-30 0.0312 33 0.214 0.730 0.477 0.253 1.491 0.056 0.512 0.376 0.160 3.168 762 0.070 0.139 -0.957 0.580 1.844 0.731
1
362T162-30 0.0312 50 0.214 0.730 0.477 0.253 1.491 0.056 0.512 0.363 0.138 4.129 762 0.070 0.139 -0.957 0.580 1.844 0.731
362T162-33 0.0346 33 0.238 0.809 0.532 0.281 1.496 0.062 0.511 0.432 0.185 3.661 1024 0.095 0.155 -0.955 0.579 1.847 0.733
362T162-33 0.0346 50 0.238 0.809 0.532 0.281 1.496 0.062 0.511 0.413 0.173 5.177 1044 0.095 0.155 -0.955 0.579 1.847 0.733
362T162-43 0.0451 33 0.310 1.054 0.696 0.366 1.499 0.080 0.509 0.603 0.263 5.197 1739 0.210 0.202 -0.950 0.576 1.846 0.735
362T162-43 0.0451 50 0.310 1.054 0.696 0.366 1.499 0.080 0.509 0.574 0.025 7.373 2141 0.210 0.202 -0.950 0.576 1.846 0.735
362T162-54 0.0566 33 0.389 1.322 0.876 0.457 1.502 0.100 0.507 0.803 0.357 7.057 2473 0.415 0.253 -0.944 0.573 1.845 0.738
362T162-54 0.0566 50 0.389 1.322 0.876 0.457 1.502 0.100 0.507 0.765 0.333 9.966 3372 0.415 0.253 -0.944 0.573 1.845 0.738
362T162-68 0.0713 33 0.489 1.665 1.122 0.577 1.514 0.124 0.504 1.089 0.496 9.802 3088 0.829 0.324 -0.936 0.567 1.850 0.744
362T162-68 0.0713 50 0.489 1.665 1.122 0.577 1.514 0.124 0.504 1.043 0.462 13.832 4679 0.829 0.324 -0.936 0.567 1.850 0.744
400T162-33 0.0346 33 0.251 0.853 0.663 0.318 1.625 0.064 0.505 0.542 0.214 4.225 944 0.100 0.194 -0.920 0.563 1.935 0.774
400T162-33 0.0346 50 0.251 0.853 0.663 0.318 1.625 0.064 0.505 0.522 1.898 5.683 944 0.100 0.194 -0.920 0.563 1.935 0.774
 ESR-2361 | Most Widely Accepted and Trusted Page 8 of 20

2
TABLE 4—TRACK (T) SECTION PROPERTIES (Continued)

Design Gross Properties Effective Properties Torsional Properties

Member Fy
Thickness Area Weight Ix Sx Rx Iy Ry Ix Sx Ma Vag J x 1000 Cw X0 m R0 β
Designation
2 4 3 3 4 3 4 6
(in) (ksi) (in ) (lb/ft) (in ) (in ) (in) (in ) (in) (in ) (in ) (in-k) (lb) (in ) (in ) (in) (in) (in)
400T162-43 0.0451 33 0.327 1.117 0.866 0.414 1.628 0.083 0.503 0.754 0.302 5.970 1739 0.222 0.252 -0.915 0.56 1.934 0.776
400T162-43 0.0451 50 0.327 1.117 0.866 0.414 1.628 0.083 0.503 0.719 0.284 8.500 2090 0.222 0.252 -0.915 0.56 1.934 0.776
400T162-54 0.0566 33 0.410 1.394 1.090 0.518 1.631 0.103 0.551 1.001 0.409 8.075 2736 0.438 0.315 -0.910 0.557 1.933 0.779
400T162-54 0.0566 50 0.410 1.394 1.090 0.518 1.631 0.103 0.551 0.955 0.382 11.442 3372 0.438 0.315 -0.910 0.557 1.933 0.779
400T162-68 0.0713 33 0.516 1.756 1.392 0.653 1.643 0.128 0.498 1.352 0.565 11.160 3419 0.874 0.403 -0.901 0.552 1.939 0.784
400T162-68 0.0713 50 0.516 1.756 1.392 0.653 1.643 0.128 0.498 1.296 0.528 15.800 5180 0.874 0.403 -0.901 0.552 1.939 0.784
550T162-33 0.0346 33 0.303 1.030 1.369 0.483 2.126 0.069 0.479 1.158 0.314 6.205 582 0.121 0.400 -0.803 0.508 2.323 0.880
550T162-33 0.0346 50 0.303 1.030 1.369 0.483 2.126 0.069 0.479 1.132 0.257 7.699 682 0.121 0.400 -0.803 0.508 2.323 0.880
550T162-43 0.0451 33 0.394 1.342 1.787 0.629 2.129 0.090 0.477 1.578 0.480 9.493 1510 0.267 0.519 -0.799 0.505 2.323 0.882
550T162-43 0.0451 50 0.394 1.342 1.787 0.629 2.129 0.090 0.477 1.523 0.437 13.072 1510 0.267 0.519 -0.799 0.505 2.323 0.882
550T162-54 0.0566 33 0.495 1.683 2.246 0.787 2.131 0.111 0.475 2.079 0.642 12.684 2739 0.528 0.648 -0.794 0.502 2.323 0.883
550T162-54 0.0566 50 0.495 1.683 2.246 0.787 2.131 0.111 0.475 1.996 0.607 18.168 2985 0.528 0.648 -0.794 0.502 2.323 0.883
550T162-68 0.0713 33 0.623 2.120 2.855 0.990 2.141 0.139 0.472 2.778 0.874 17.269 4347 1.056 0.821 -0.787 0.497 2.329 0.886
550T162-68 0.0713 50 0.623 2.120 2.855 0.990 2.141 0.139 0.472 2.676 0.825 24.696 5350 1.056 0.821 -0.787 0.497 2.329 0.886
600T162-33 0.0346 33 0.320 1.089 1.677 0.544 2.289 0.071 0.470 1.436 0.340 6.715 624 0.128 0.487 -0.771 0.492 2.461 0.902
600T162-33 0.0346 50 0.320 1.089 1.677 0.544 2.289 0.071 0.470 1.404 0.280 8.376 624 0.128 0.487 -0.771 0.492 2.461 0.902
600T162-43 0.0451 33 0.417 1.419 2.188 0.708 2.291 0.092 0.468 1.942 0.548 10.819 1382 0.283 0.632 -0.767 0.489 2.461 0.903
600T162-43 0.0451 50 0.417 1.419 2.188 0.708 2.291 0.092 0.468 1.888 0.472 14.119 1382 0.283 0.632 -0.767 0.489 2.461 0.903
600T162-54 0.0566 33 0.523 1.779 2.750 0.886 2.293 0.114 0.466 2.552 0.729 14.411 2732 0.559 0.789 -0.762 0.486 2.461 0.904
600T162-54 0.0566 50 0.523 1.779 2.750 0.886 2.293 0.114 0.466 2.454 0.691 20.700 2372 0.559 0.789 -0.762 0.486 2.461 0.904
600T162-68 0.0713 33 0.658 2.241 3.479 1.114 2.299 0.141 0.463 3.379 0.983 19.428 4347 1.116 0.992 -0.756 0.482 2.464 0.906
600T162-68 0.0713 50 0.658 2.241 3.479 1.114 2.299 0.141 0.463 3.257 0.930 27.841 5350 1.116 0.992 -0.756 0.482 2.464 0.906
For SI: 1 inch = 25.4 mm;1 lb/ft = 14.5939 N/m; 1 in-k = 12.8 N-m; 1 lb = 4.448 N; 1 ksi = 6.89 MPa.
1
For applications in accordance with the IRC, use of all 162T162-XX, 250T162-XX, 350T162-27, 350T162-30, 362T162-27 and 362T162-30 is applicable only for engineered designs in accordance with IRC Section R301.1.3.
2
Member Designation identification provides nominal dimensions as shown in the example below:
Example: 600T162-43; 600 = 6 inch depth (Depth measured from the outside face to outside face of flanges), T = T-Section, 162 = 1.625 inch flange width, 43 = thickness designation of 43 mils or
0.0428 inches.
ESR-2361 | Most Widely Accepted and Trusted Page 9 of 20

1,2,3
TABLE 5—ALLOWABLE WEB CRIPPLING LOAD (lbs)—SINGLE MEMBERS

YIELD CONDITION 1 CONDITION 2 CONDITION 3 CONDITION 4

SECTION BEARING LENGTH (in) BEARING LENGTH (in) BEARING LENGTH (in) BEARING LENGTH (in)
STRENGTH
DESIGNATION
(ksi)
1 3.5 4 6 1 3.5 4 6 1 3.5 4 6 1 3.5 4 6
350S162 - 33 33 166 260 274 323 324 445 463 526 131 175 182 205 384 484 499 551
350S162 - 43 33 278 428 451 528 571 768 798 900 240 315 326 365 680 842 866 949
350S162 - 54 33 420 638 670 783 879 1162 1204 1351 392 507 524 583 1086 1324 1359 1482
350S162 - 54 50 637 967 1016 1186 1331 1761 1825 2046 594 768 794 883 1645 2005 2059 2245
350S162 - 68 33 637 951 998 1160 1351 1756 1816 2025 640 813 839 928 1736 2085 2137 2317
350S162 - 68 50 965 1441 1512 1758 2047 2660 2751 3068 970 1232 1271 1406 2631 3159 3238 3510
362S162 - 33 33 165 259 273 322 323 444 462 525 129 173 179 202 381 480 495 547
362S162 - 43 33 277 427 449 526 570 767 796 898 236 311 322 360 675 836 860 943
362S162 - 54 33 419 636 668 780 877 1160 1202 1348 388 501 518 577 1079 1316 1351 1473
362S162 - 54 50 634 963 1012 1182 1329 1758 1822 2043 588 760 785 874 1635 1994 2047 2232
362S162 - 68 33 635 948 995 1157 1349 1753 1813 2022 635 806 831 920 1728 2074 2126 2305
362S162 - 68 50 962 1437 1507 1752 2044 2657 2747 3064 961 1221 1259 1393 2618 3143 3221 3492
400S162 - 33 33 163 256 269 317 322 442 460 522 122 164 170 192 372 469 483 534
400S162 - 43 33 274 422 444 520 567 763 792 893 227 299 309 346 662 819 843 924
400S162 - 54 33 415 629 661 772 873 1155 1197 1342 376 485 502 558 1061 1293 1328 1448
400S162 - 54 50 628 954 1002 1170 1323 1750 1813 2034 569 735 760 846 1607 1960 2012 2194
400S162 - 68 33 629 940 986 1147 1344 1746 1806 2014 617 784 809 895 1702 2044 2094 2271
400S162 - 68 50 953 1424 1494 1737 2036 2646 2736 3051 936 1188 1226 1356 2579 3096 3173 3440
550S162 - 33 33 155 243 256 302 315 432 450 511 100 134 139 157 339 428 441 487
550S162 - 43 33 262 405 426 499 556 749 778 877 195 256 265 297 614 760 782 858
550S162 - 54 33 400 607 638 745 859 1136 1177 1320 331 428 443 493 995 1213 1246 1358
550S162 - 54 50 606 920 966 1128 1302 1722 1784 2001 502 649 671 746 1508 1838 1887 2058
550S162 - 68 33 609 910 955 1111 1324 1721 1780 1985 557 707 729 807 1611 1934 1982 2149
550S162 - 68 50 923 1380 1447 1683 2007 2608 2697 3007 844 1071 1105 1223 2441 2931 3003 3256
600S162 - 33 33 153 240 253 297 313 430 447 507 93 125 130 146 329 416 429 473
600S162 - 43 33 259 400 420 493 553 745 773 872 185 243 252 282 600 743 764 838
600S162 - 54 33 395 600 631 736 855 1131 1172 1314 318 411 425 473 975 1189 1221 1331
600S162 - 54 50 599 909 956 1116 1295 1713 1775 1991 482 623 644 716 1478 1802 1850 2017
600S162 - 68 33 604 902 946 1100 1318 1714 1772 1976 539 684 706 781 1583 1901 1949 2113
600S162 - 68 50 914 1366 1433 1666 1998 2596 2685 2994 816 1036 1069 1183 2399 2881 2952 3201

(Continued)
ESR-2361 | Most Widely Accepted and Trusted Page 10 of 20

NOTES FOR TABLE 5

For SI: 1 inch = 25.4mm, 1 lb = 4.448 N.
1
For multiple members, multiply the listed capacity of a single member by the number of members in the assembly.
2
Values shown are for unpunched and punched members. For punched members, the clear distance between the edge of bearing and the edge of the punch-out must be at least two times the depth of the web to a
maximum of 10 inches.
3
Condition 1 - End Reaction - One Flange Loading
Condition 2 - Interior Reaction - One Flange Loading
Condition 3 - End Reaction - Two Flange Loading
Condition 4 - Interior Reaction - Two Flange Loading
See Figure 4 for Conditions 1, 2, 3 and 4.

1,2,3
TABLE 6—ALLOWABLE WEB CRIPPLING LOAD (lb)—BACK-TO-BACK MEMBERS

YIELD CONDITION 1 CONDITION 2 CONDITION 3 CONDITION 4

SECTION BEARING LENGTH (in) BEARING LENGTH (in) BEARING LENGTH (in) BEARING LENGTH (in)
DESIGNATION STRENGTH
(ksi)
1 3.5 4 6 1 3.5 4 6 1 3.5 4 6 1 3.5 4 6
See See See See See See See See See See See See
350S162 - 33 33 776 917 463 984
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See See See See See
350S162 - 43 33 1272 1590 838 1808
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See See See See See
350S162 - 54 33 1892 2474 1361 2943
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See See See See See
350S162 - 54 50 2867 3749 2062 4459
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See See See See See
350S162 - 68 33 2829 3863 2208 4776
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See See See See See
350S162 - 68 50 4286 5853 3346 7236
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See See See See See
362S162 - 33 33 776 916 458 972
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See See See See See
362S162 - 43 33 1271 1589 830 1790
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See See See See See
362S162 - 54 33 1892 2473 1349 2918
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See See See See See
362S162 - 54 50 2867 3747 2045 4422
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See See See See See
362S162 - 68 33 2828 3861 2193 4742
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See See See See See
362S162 - 68 50 4285 5851 3322 7185
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See
400S162 - 33 33 776 1181 915 1083 442 557 937 1183
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See
400S162 - 43 33 1271 1900 1587 1850 806 998 1739 2154
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See
400S162 - 54 33 1891 2782 2470 2844 1317 1605 2848 3472
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See
400S162 - 54 50 2866 4215 3743 4309 1995 2432 4315 5260
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
ESR-2361 | Most Widely Accepted and Trusted Page 11 of 20

1,2,3
TABLE 6—ALLOWABLE WEB CRIPPLING LOAD (lb)—BACK-TO-BACK MEMBERS (Continued)

YIELD CONDITION 1 CONDITION 2 CONDITION 3 CONDITION 4

SECTION BEARING LENGTH (in) BEARING LENGTH (in) BEARING LENGTH (in) BEARING LENGTH (in)
DESIGNATION STRENGTH
(ksi)
1 3.5 4 6 1 3.5 4 6 1 3.5 4 6 1 3.5 4 6
See See See See See See See See
400S162 - 68 33 2827 4087 3857 4387 2147 2578 4644 5576
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See See See See See
400S162 - 68 50 4284 6193 5844 6646 3253 3906 7036 8448
Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4 Note 4
See See See See
550S162 - 33 33 774 1179 1239 909 1077 1102 384 484 499 815 1028 1060
Note 4 Note 4 Note 4 Note 4
See See See See
550S162 - 43 33 1269 1897 1990 1579 1841 1879 721 893 919 1556 1927 1982
Note 4 Note 4 Note 4 Note 4
See See See See
550S162 - 54 33 1888 2778 2909 2459 2831 2886 1200 1463 1502 2595 3164 3249
Note 4 Note 4 Note 4 Note 4
See See See See
550S162 - 54 50 2861 4208 4408 3725 4289 4372 1818 2217 2276 3933 4794 4922
Note 4 Note 4 Note 4 Note 4
See See See See
550S162 - 68 33 2823 4082 4268 3841 4369 4447 1985 2384 2443 4294 5186 5284
Note 4 Note 4 Note 4 Note 4
See See See See
550S162 - 68 50 4278 6185 6467 5820 6619 6738 3008 3612 3702 6506 7812 8005
Note 4 Note 4 Note 4 Note 4
See See See See
600S162 - 33 33 774 1178 1238 908 1075 1100 366 462 477 778 982 1012
Note 4 Note 4 Note 4 Note 4
See See See See
600S162 - 43 33 1268 1896 1989 1576 1838 1876 696 862 886 1501 1859 1912
Note 4 Note 4 Note 4 Note 4
See See See See
600S162 - 54 33 1888 2776 2908 2455 2827 2882 1165 1420 1458 2520 3072 3154
Note 4 Note 4 Note 4 Note 4
See See See See
600S162 - 54 50 2860 4207 4406 3720 4283 4366 1765 2152 2209 3818 4654 4778
Note 4 Note 4 Note 4 Note 4
See See See See
600S162 - 68 33 2822 4080 4267 3836 4363 4441 1937 2326 2383 4189 5030 5154
Note 4 Note 4 Note 4 Note 4
See See See See
600S162 - 68 50 4276 6182 6465 5812 6611 6729 2935 3524 3611 6347 7621 7810
Note 4 Note 4 Note 4 Note 4
For SI: 1 inch = 25.4mm, 1 lb = 4.448 N.
1
For multiple members, multiply the listed capacity of a single member by the number of members in the assembly.
2
Values shown are for unpunched and punched members. For punched members, the clear distance between the edge of bearing and the edge of the punch-out must be at least two times the depth of the web to a
maximum of 10 inches.
3
Condition 1 - End Reaction - One Flange Loading
Condition 2 - Interior Reaction - One Flange Loading
Condition 3 - End Reaction - Two Flange Loading
Condition 4 - Interior Reaction - Two Flange Loading
4
Bearing length to web height ratio, N/h, exceeds limit of 1. Web Stiffeners are required.
See Figure 4 for Conditions 1, 2, 3 and 4.
ESR-2361 | Most Widely Accepted and Trusted Page 12 of 20
1,2,3,4
TABLE 7—LIMITING WALL HEIGHTS—NONLOAD-BEARING WALLS—NON-COMPOSITE

LATERAL LOAD
STUD 5 psf 7.5 psf 10 psf
MEMBER Fy
SPACING
DESIGNATION (ksi) DEFLECTION LIMIT
(in) o.c.
L/120 L/240 L/120 L/240 L/120 L/240
16 19'-7" 16'-0" 16'-0" 14'-0" 13'-10" 12'-8"
33
24 16'-0" 14'-0" 13'-1" 12'-2" 11'-4" 11'-1"
350S162-27
16 20'-0" 16'-0" 17'-6" 14'-0" 15'-10" 12'-8"
50
24 17'-6" 14'-0" 15'-2" 12'-2" 13'-2" 11'-1"
16 20' 10" 16' 6" 17'-2" 14'-5" 14'-10" 13'-1"
33
24 17' 2" 14' 5" 14'-0" 12'-7" 12'-1" 11'-5"
350S162-30
16 20' 10" 16' 6" 18' 1" 14'-4" 16'-5" 13'-1"
50
24 18' 1" 14' 4" 15'-10" 12'-7" 14'-1" 11'-5"
16 21'-6" 17' 1" 18'-4" 14'-11" 15'-11" 13'-6"
33
24 18'-4" 14'-11" 15'-0" 13'-0" 13'-0" 11'-10"
350S162-33
16 21' 6" 17' 1" 18'-9" 14'-11" 17' 1" 13'-6"
50
24 18' 9" 14'-11" 16'-5" 13'-0" 14'-11" 11'-10"
16 23' 5" 18' 7" 20'-5" 16'-2" 18'-7" 14'-9"
33
24 20'-5" 16' 2" 17'-10" 14'-2" 15'-3" 12'-10"
350S162-43
16 23' 5" 18' 7" 20'-5" 16'-2" 18'-7" 14'-9"
50
24 20'-5" 16' 2" 17'-10" 14'-2" 16'-2" 12'-10"
16 25'-1" 19'-11" 21'-11" 17'-4" 19'-11" 15'-9"
33
24 21'-11" 17' 4" 19'-1" 15'-2" 17' 1" 13'-9"
350S162-54
16 25'-1" 19'-11" 21'-11" 17'-4" 19'-11" 15'-9"
50
24 21'-11" 17' 4" 19'-1" 15'-2" 17' 1" 13'-9"
16 19' 11" 16' 5" 16'-4" 14'-4" 14'-2" 13'-0"
33
24 16' 3" 14' 4" 13'-4" 12'-6" 11'-6" 11'-5"
362S162-27
16 20' 7" 16' 5" 17'-11" 14'-4" 16'-4" 13'-0"
50
24 18' 0" 14' 4" 15'-6" 12'-6" 13'-5" 11'-5"
16 21' 4' 16' 11" 17'-6" 14'-10" 15'-2" 13'-5"
33
24 17' 6" 14' 10" 14'-3" 12'-11" 12'-4" 11'-9"
362S162-30
16 21' 4" 16' 11" 18'-7" 14'-10" 16'-11" 13'-5"
50
24 18' 7" 14' 9' 16'-3" 12'-11" 14'-4" 11'-9"
16 22' 1" 17' 6" 18'-8" 15'-3" 16'-2" 13'-10"
33
24 18' 9" 15' 4" 15'-2" 13'-4" 13'-2" 12'-1"
362S162-33
16 22' 1" 17' 6" 19'-3" 15'-3" 17'-6" 13'-10"
50
24 19' 3" 15' 4" 16'-10" 13'-4" 15'-3" 12'-1"
16 24' 0" 19' 1" 21'-0" 16'-8" 19'-1" 15'-2"
33
24 21' 0" 16' 8" 18'-0" 14'-7" 15'-7" 13'-3"
362S162-43
16 24' 0" 19' 1" 21'-0" 16'-8" 19'-1" 15'-2"
50
24 21' 0" 16' 8" 18'-4" 14'-7" 16'-8" 13'-3"
16 25' 9" 20' 5" 22'-6" 17'-10" 20'-5" 16'-2"
33
24 22' 6" 17' 10" 19'-8" 15'-7" 17'-6" 14'-2"
362S162-54
16 25' 9" 20' 5" 22'-6" 17'-10" 20'-5" 16'-2"
50
24 22' 6" 17' 10" 19'-8" 15'-7" 17'-10" 14'-2"
ESR-2361 | Most Widely Accepted and Trusted Page 13 of 20
1,2,3,4
TABLE 7—LIMITING WALL HEIGHTS—NONLOAD-BEARING WALLS—NON-COMPOSITE (Continued)

LATERAL LOAD
STUD 5 psf 7.5 psf 10 psf
MEMBER Fy
SPACING
DESIGNATION (ksi) DEFLECTION LIMIT
(in) o.c.
L/120 L/240 L/120 L/240 L/120 L/240
16 21' 1" 17' 9" 17'-3" 15'-6" 14'-11" 14'-1"
33
24 17' 2" 15' 6" 14'-1" 13'-6" 12'-2" 12'-2"
400S162-27
16 22' 3" 17' 7" 19'-5" 15'-6" 17'-4" 14'-1"
50
24 19' 5" 15' 5" 16'-4" 13'-6" 14'-1" 12'-2"
16 27'-4" 23'-5" 17'-3" 15'-6" 14'-11" 14'-1"
33
24 22'-4" 20'-6" 14'-1" 13'-6" 12'-2" 12'-2"
400S162-30
16 29'-7" 23'-5" 19'-5" 15'-6" 17'-4" 14'-1"
50
24 25'-5" 20'-6" 16'-4" 13'-6" 14'-1" 12'-2"
16 23' 10" 18' 11" 19'-10" 16'-6" 17'-2" 15'-0"
33
24 19' 10" 16' 6" 16'-2" 14'-5" 14'-0" 13'-1"
400S162-33
16 23' 10" 18' 11" 20'-10" 16'-6" 18'-11" 15'-0"
50
24 20' 10" 16' 6" 18'-2" 14'-5" 16'-2" 13'-1"
16 25' 11" 20' 7" 22'-8" 18'-0" 20'-3" 16'-4"
33
24 22' 8" 18' 0" 19'-1" 15'-8" 16'-6" 14'-3"
400S162-43
16 25' 11" 20' 7" 22'-8" 18'-0" 20'-7" 16'-4"
50
24 22' 8" 18' 0" 19'-1" 15'-8" 18'-0" 14'-3"
16 27' 10" 22' 1" 24'-3" 19'-3" 22'-10" 17'-6"
33
24 24' 3" 19' 3" 21'-2" 16'-10" 18'-7" 15'-3"
400S162-54
16 27' 10" 22' 1" 24'-3" 19'-3" 22'-10" 17'-6"
50
24 24' 3" 19' 3" 21'-2" 16'-10" 19'-3" 15'-3"
16 25' 7" 22' 9" 20'-10" 19'-10" 17'-10" 17'-10"
33
24 20' 10" 19' 10" 15'-10" 15'-10" 11'-11" 11'-11"
550S162-27
16 28' 7" 22' 9" 23'-9" 19'-10" 20'-6" 18'-0"
50
24 23' 9" 19' 10" 19'-4" 17'-3" 16'-9" 15'-6"
16 25' 7" 22' 9" 27'-4" 23'-5" 22'-4" 20'-6"
33
24 20' 10" 19' 10" 22'-4" 20'-6" 18'-2" 17'-11"
550S162-30
16 28' 7" 22' 9" 25'-5" 20'-6" 22'-0" 18'-7"
50
24 23' 9" 19' 10" 20'-9" 17'-11" 18'-0" 16'-3"
16 29' 4" 24' 3" 23'-11" 21'-2" 20'-9" 19'-3"
33
24 23' 11" 21' 2" 19'-6" 18'-6" 16'-11" 16'-10"
550S162-33
16 30' 7" 24' 3" 26'-8" 21'-2" 23'-8" 19'-3"
50
24 26' 8" 21' 2" 22'-4" 18'-6" 19'-4" 16'-10"
16 33' 3" 26' 5" 29'-1" 23'-1" 25'-7" 20'-11"
33
24 29' 1" 23' 1" 24'-1" 20'-2" 20'-11" 18'-4"
550S162-43
16 33' 3" 26' 5" 29'-1" 23'-1" 26'-5" 20'-11"
50
24 29' 1" 23' 1" 25'-5" 20'-2" 23'-1" 18'-4"
16 35' 9" 28' 4" 31'-2" 24'-9" 28'-4" 22'-6"
33
24 31' 2" 24' 9" 27'-3" 21'-7" 24'-4" 19'-8"
550S162-54
16 35' 9" 28' 4" 31'-2" 24'-9" 28'-4" 22'-6"
50
24 31' 2" 24' 9" 27'-3" 21'-7" 24'-9" 19'-8"
 ESR-2361 | Most Widely Accepted and Trusted Page 14 of 20
1,2,3,4
TABLE 7—LIMITING WALL HEIGHTS—NONLOAD-BEARING WALLS—NON-COMPOSITE (Continued)

LATERAL LOAD
STUD 5 psf 7.5 psf 10 psf
MEMBER Fy
SPACING
DESIGNATION (ksi) DEFLECTION LIMIT
(in) o.c.
L/120 L/240 L/120 L/240 L/120 L/240
16 28'-7" 25'-2" 23'-4" 21'-11" 23'-0" 19'-11"
33
24 23'-4" 21'-11" 19'-0" 19'-0" 14'-3" 14'-3"
600S162-30
16 31'-8" 25'-2" 26'-7" 21'-11" 23'-0" 19'-11"
50
24 26'-7" 21'-11" 21'-8" 19'-2" 18'-9" 17'-5"
16 30' 9" 26' 0" 25'-1" 22'-8" 21'-9" 20'-7"
33
24 25' 1" 22' 8" 20'-6" 19'-10" 17'-6" 17'-6"
600S162-33
16 32' 9" 26' 0" 28'-7" 22'-8" 24'-9" 20'-7"
50
24 28' 7" 22' 8" 23'-4" 19'-10" 20'-2" 18'-0"
16 35' 8" 28' 4" 31'-0" 24'-9" 26'-10" 22'-5"
33
24 31' 0" 24' 9" 25'-4" 21'-7" 21'-11" 19'-7"
600S162-43
16 35' 8" 28' 4" 31'-2" 24'-9" 28'-4" 22'-5"
50
24 31' 2" 24' 9" 27'-3" 21'-7" 24'-4" 19'-7"
16 38' 3" 30' 4" 33'-5" 26'-6" 30'-4" 24'-1"
33
24 33' 5" 26' 6" 29'-2" 23'-2" 25'-7" 21'-1"
600S162-54
16 38' 3" 30' 4" 33'-5" 26'-6" 30'-4" 24'-1"
50
24 33' 5" 26' 6" 29'-2" 23'-2" 26'-6" 21'-1"
For SI: 1 inch = 25.4mm, 1 lb = 4.448 N.
1
Lateral loads have NOT been reduced for strength or deflection checks. Full lateral load is applied.
2
Limiting heights are based on continuous support of each flange over the full length of the stud.
3
Limiting heights are based on steel framing only (non-composite).
4
Web crippling checks are based on end-one flange loading condition using 1-inch end bearing.
Notes for combined Axial and Lateral Load Tables (Tables 8, 9, 10, 11 and 12)

1. Allowable axial loads listed in kips (1 kip = 1000 pounds).

2. Listed lateral pressures and axial loads have not been modified for 1/3 stress increase based on wind/earthquake
or multiple transient loads.

3. Allowable axial loads based on lateral and torsional bracing at a maximum spacing of 4 feet on center.

4. The 5 psf live load has not been reduced for deflection checks. For 15 psf or higher wind pressure, read the note below.

Note: 2015 and 2012 IBC/ASCE 7-10: Due to the change in the model building codes, design wind pressures determined using 2015 and
2012 IBC/ASCE 7-10 are strength level loads (LRFD) in comparison to those determined in earlier IBC codes which were service level
loads (ASD). The load/span tables that follow are based on service level (ASD) wind loads. Therefore, to properly use the load/span tables
in, multiply the 2015 and 2012 IBC/ ASCE 7-10 design wind pressures by 0.6 (Reference section 2.4 ASCE 7-10) prior to entering the
load/span tables.

5. End supports have not been checked for web crippling. Refer web crippling capacity tables.

6. All tables are based on simple (single) span.

7. Cells marked with an alphabetic letter after load meet deflection criteria. Blank cells do not meet L/120.
a
Deflection meets L/720.
b
Deflection meets L/600.
c
Deflection meets L/480.
d
Deflection meets L/360.
e
Deflection meets L/240.
f
Deflection meets L/120.

For SI: 1 inch = 25.4 mm, 1 ft = 304.8mm, 1 lb = 4.448 N, 1 psf = 48 Pa.

 ESR-2361 | Most Widely Accepted and Trusted Page 15 of 20

TABLE 8—COMBINED LATERAL AND AXIAL LOADS - ALLOWABLE AXIAL LOAD (kips) WITH 5 psf LATERAL LOAD

350S162- 362S162- 400S162- 550S162- 600S162-

MAX.
WALL 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi
STUD
HEIGHT
SPACING Stud Thickness (mils)
(ft)
(in)
33 43 54 68 33 43 54 68 33 43 54 68 33 43 54 68 33 43 54 68
a a a a a a a a a a a a a a a a a a a a
12 1.81 2.56 3.97 5.08 1.87 2.65 4.15 5.38 2.03 2.87 4.62 6.18 2.39 3.38 5.63 7.45 2.42 3.40 5.61 7.45
a a a a a a a a a a a a a a a a a a a a
8 16 1.74 2.48 3.90 5.01 1.80 2.57 4.08 5.31 1.96 2.80 4.55 6.11 2.34 3.33 5.58 7.41 2.37 3.35 5.57 7.41
a a a a a a a a a a a a a a a a a a a a
24 1.58 2.32 3.76 4.87 1.65 2.42 3.94 5.17 1.82 2.65 4.42 5.97 2.24 3.23 5.49 7.32 2.28 3.27 5.49 7.33
a a a a a a a a a a a a a a a a a a a a
12 1.67 2.38 3.65 4.67 1.74 2.48 3.86 4.99 1.91 2.72 4.37 5.85 2.32 3.31 5.55 7.41 2.38 3.36 5.57 7.41
a a a a a a a a a a a a a a a a a a a a
9 16 1.57 2.28 3.56 4.58 1.64 2.38 3.77 4.90 1.82 2.63 4.28 5.76 2.26 3.24 5.49 7.35 2.32 3.30 5.52 7.36
a a a a a a a a a a a a a a a a a a a a
24 1.39 2.09 3.39 4.41 1.46 2.19 3.60 4.72 1.65 2.45 4.11 5.59 2.13 3.12 5.38 7.24 2.20 3.19 5.42 7.26
a a a a a a a a a a a a a a a a a a a a
12 1.51 2.18 3.29 4.23 1.58 2.29 3.53 4.55 1.77 2.56 4.07 5.47 2.25 3.22 5.41 7.35 2.33 3.31 5.53 7.37
a a a a a a a a a a a a a a a a a a a a
10 16 1.40 2.07 3.19 4.12 1.47 2.17 3.42 4.44 1.67 2.45 3.97 5.36 2.16 3.14 5.34 7.27 2.25 3.24 5.46 7.30
a a a a a a a a a a a a a a a a a a a a
24 1.19 1.84 2.99 3.92 1.26 1.95 3.22 4.23 1.46 2.23 3.77 5.14 2.00 2.99 5.19 7.12 2.10 3.11 5.33 7.17
a a a a a a a a a a a a a a a a a a a a
12 1.18 1.75 2.56 3.31 1.25 1.87 2.79 3.60 1.46 2.17 3.41 4.54 2.05 3.00 5.04 6.87 2.17 3.15 5.35 7.25
b a a a a a a a a a a a a a a a a a a a
12 16 1.04 1.61 2.44 3.18 1.11 1.72 2.66 3.47 1.32 2.02 3.27 4.39 1.93 2.89 4.93 6.76 2.06 3.05 5.25 7.15
d c a a c b a a b a a a a a a a a a a a
24 0.79 1.34 2.21 2.94 0.86 1.44 2.42 3.22 1.06 1.74 3.01 4.12 1.71 2.68 4.71 6.54 1.85 2.85 5.05 6.95
c a a a b a a a a a a a a a a a a a a a
12 0.86 1.33 1.95 2.54 0.93 1.44 2.14 2.78 1.14 1.75 2.71 3.57 1.81 2.72 4.54 6.23 1.95 2.91 4.93 6.77
d c b a d b a a c a a a a a a a a a a a
14 16 0.71 1.17 1.82 2.40 0.78 1.28 2.00 2.64 0.98 1.58 2.55 3.41 1.66 2.57 4.39 6.07 1.81 2.78 4.80 6.63
e d d c e d c b d c b a a a a a a a a a
24 0.46 0.89 1.58 2.16 0.52 0.99 1.75 2.38 0.70 1.26 2.27 3.11 1.37 2.29 4.11 5.78 1.54 2.51 4.53 6.35
d c b a d c b a c b a a a a a a a a a a
12 0.59 0.96 1.48 1.95 0.65 1.06 1.63 2.14 0.84 1.35 2.12 2.78 1.53 2.39 3.95 5.45 1.71 2.62 4.41 6.10
e d d c e d c b d c b a a a a a a a a a
16 16 0.45 0.80 1.35 1.81 0.51 0.90 1.49 2.00 0.68 1.17 1.96 2.61 1.35 2.20 3.77 5.26 1.53 2.45 4.24 5.91
f e e d f e e d e e d c c a a a b a a a
24 0.21 0.54 1.12 1.57 0.25 0.61 1.25 1.74 0.39 0.85 1.67 2.31 1.02 1.87 3.43 4.90 1.20 2.12 3.91 5.57
 ESR-2361 | Most Widely Accepted and Trusted Page 16 of 20

TABLE 9—COMBINED LATERAL AND AXIAL LOADS - ALLOWABLE AXIAL LOAD (kips) WITH 15 psf LATERAL LOAD

350S162- 362S162- 400S162- 550S162- 600S162-

MAX.
WALL 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi
STUD
HEIGHT
SPACING Stud Thickness (mils)
(ft)
(in)
33 43 54 68 33 43 54 68 33 43 54 68 33 43 54 68 33 43 54 68
a a a a a a a a a a a a a a a a a a a a
12 1.37 2.10 3.56 4.66 1.44 2.20 3.74 4.96 1.62 2.45 4.22 5.77 2.08 3.09 5.36 7.19 2.14 3.14 5.37 7.22
a a a a a a a a a a a a a a a a a a a a
8 16 1.16 1.89 3.36 4.46 1.23 1.99 3.55 4.76 1.42 2.25 4.04 5.57 1.93 2.95 5.22 7.06 2.00 3.02 5.25 7.10
a a a a a a a a a a a a a a a a a a a a
24 0.78 1.49 2.99 4.08 0.85 1.59 3.17 4.38 1.05 1.86 3.67 5.18 1.64 2.68 4.96 6.80 1.73 2.77 5.02 6.88
a a a a a a a a a a a a a a a a a a a a
12 1.13 1.82 3.14 4.16 1.21 1.93 3.35 4.47 1.40 2.20 3.87 5.33 1.94 2.94 5.20 7.07 2.02 3.03 5.26 7.11
a a a a a a a a a a a a a a a a a a a a
9 16 0.90 1.57 2.91 3.92 0.97 1.67 3.12 4.23 1.17 1.95 3.64 5.08 1.75 2.77 5.03 6.90 1.85 2.87 5.11 6.96
c b a a c a a a b a a a a a a a a a a a
24 0.46 1.11 2.48 3.48 0.53 1.21 2.68 3.77 0.73 1.49 3.20 4.61 1.38 2.42 4.69 6.56 1.51 2.56 4.81 6.67
a a a a a a a a a a a a a a a a a a a a
12 0.90 1.53 2.71 3.63 0.97 1.64 2.94 3.94 1.17 1.93 3.48 4.83 1.77 2.77 4.97 6.90 1.89 2.91 5.14 6.98
c a a a b a a a a a a a a a a a a a a a
10 16 0.64 1.25 2.45 3.37 0.71 1.36 2.67 3.66 0.90 1.64 3.21 4.54 1.54 2.56 4.76 6.69 1.67 2.71 4.94 6.80
d c b a c c b a c a a a a a a a a a a a
24 0.17 0.74 1.99 2.88 0.23 0.84 2.18 3.15 0.41 1.12 2.70 3.99 1.10 2.14 4.35 6.26 1.26 2.32 4.57 6.43
d c b a d b a a b a a a a a a a a a a a
12 0.47 0.98 1.90 2.62 0.53 1.08 2.10 2.88 0.72 1.37 2.65 3.73 1.39 2.36 4.40 6.22 1.54 2.56 4.76 6.66
e d c b e d c b d c b a a a a a a a a a
12 16 0.18 0.67 1.62 2.33 0.24 0.76 1.81 2.58 0.41 1.03 2.33 3.38 1.08 2.07 4.10 5.91 1.25 2.28 4.48 6.37
e e d e d d d d c b a a a a a a a
24 -- 0.13 1.13 1.81 -- 0.20 1.29 2.03 -- 0.43 1.75 2.76 0.52 1.51 3.54 5.32 0.70 1.75 3.94 5.82
e e d c e d d d d c c a a a a a a a a a
12 0.13 0.53 1.27 1.83 0.18 0.61 1.42 2.03 0.33 0.86 1.89 2.70 0.97 1.90 3.71 5.36 1.15 2.13 4.15 5.95
e e d e e d e d d c c a a a a a a a
14 16 -- 0.22 1.00 1.54 -- 0.29 1.14 1.73 0.01 0.50 1.56 2.35 0.61 1.53 3.34 4.97 0.79 1.78 3.79 5.58
f e f e e d c b b c b a a
24 -- -- 0.53 1.04 -- -- 0.64 1.19 -- -- 0.98 1.72 -- 0.86 2.66 4.24 0.14 1.12 3.11 4.87
f e d e e d e e d c c b a a b a a a
12 -- 0.20 0.82 1.25 -- 0.26 0.93 1.41 0.03 0.44 1.30 1.92 0.58 1.41 2.98 4.42 0.75 1.67 3.45 5.08
16 16 -- -- 0.57
f
0.98
e
-- -- 0.66
f
1.12
e
-- 0.09
e
0.98
e
1.58
d
0.18
d
1.00
c
2.57
b
3.97
a
0.35
c
1.26
b
3.03
a
4.64
a

24 -- -- 0.13
f
0.51
f
-- -- 0.19
f
0.62
f
-- -- 0.42
f
0.98
e
-- 0.28
e
1.83
d
3.18
c
-- 0.51
d
2.28
c
3.82
b
 ESR-2361 | Most Widely Accepted and Trusted Page 17 of 20

TABLE 10—COMBINED LATERAL AND AXIAL LOADS - ALLOWABLE AXIAL LOAD (kips) WITH 20 psf LATERAL LOAD

350S162- 362S162- 400S162- 550S162- 600S162-

MAX.
WALL 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi
STUD
HEIGHT
SPACING Stud Thickness (mils)
(ft)
(in)
33 43 54 68 33 43 54 68 33 43 54 68 33 43 54 68 33 43 54 68
a a a a a a a a a a a a a a a a a a a a
12 1.16 1.89 3.36 4.46 1.23 1.99 3.55 4.76 1.42 2.25 4.04 5.57 1.93 2.95 5.22 7.06 2.00 3.02 5.25 7.10
a a a a a a a a a a a a a a a a a a a a
8 16 0.90 1.62 3.11 4.21 0.98 1.72 3.30 4.50 1.17 1.99 3.79 5.31 1.74 2.77 5.05 6.89 1.82 2.85 5.10 6.95
c b a a b a a a b a a a a a a a a a a a
24 0.43 1.11 2.64 3.72 0.50 1.21 2.82 4.01 0.70 1.50 3.32 4.81 1.35 2.41 4.70 6.55 1.47 2.53 4.79 6.65
a a a a a a a a a a a a a a a a a a a a
12 0.90 1.57 2.91 3.92 0.97 1.68 3.12 4.23 1.17 1.95 3.64 5.08 1.75 2.77 5.03 6.90 1.85 2.87 5.11 6.96
c a a a b a a a a a a a a a a a a a a a
9 16 0.60 1.26 2.62 3.62 0.67 1.36 2.82 3.92 0.87 1.64 3.34 4.76 1.50 2.54 4.80 6.67 1.62 2.66 4.91 6.76
d c b a d c b a c b a a a a a a a a a a
24 0.07 0.69 2.08 3.06 0.13 0.78 2.27 3.34 0.33 1.07 2.78 4.16 1.03 2.09 4.36 6.23 1.18 2.25 4.51 6.38
c a a a b a a a a a a a a a a a a a a a
12 0.64 1.25 2.45 3.37 0.70 1.36 2.67 3.66 0.90 1.64 3.21 4.54 1.54 2.56 4.76 6.69 1.67 2.71 4.94 6.80
d c b a d c a a c a a a a a a a a a a a
10 16 0.32 0.91 2.14 3.03 0.38 1.01 2.34 3.32 0.57 1.29 2.87 4.17 1.24 2.28 4.48 6.40 1.40 2.45 4.69 6.55
d d c d c b c c b a a a a a a a a
24 -- 0.29 1.56 2.43 -- 0.38 1.74 2.69 -- 0.64 2.24 3.48 0.69 1.74 3.95 5.85 0.86 1.94 4.20 6.06
e d c b e d c b d c b a a a a a a a a a
12 0.18 0.67 1.62 2.33 0.24 0.76 1.81 2.58 0.41 1.03 2.33 3.38 1.08 2.07 4.10 5.91 1.25 2.28 4.48 6.37
e d c e d c d d b b a a a a a a a
12 16 -- 0.30 1.29 1.97 -- 0.38 1.45 2.20 -- 0.62 1.94 2.96 0.70 1.69 3.72 5.51 0.88 1.92 4.11 6.00
e e e e e d b a a c a a a
24 -- -- 0.70 1.35 -- -- 0.84 1.55 -- -- 1.25 2.20 -- 0.99 3.01 4.77 0.19 1.24 3.43 5.30
e e d e e d e d d c c a a a a a a a
12 -- 0.22 1.00 1.54 -- 0.29 1.14 1.73 0.01 0.50 1.56 2.35 0.61 1.53 3.34 4.97 0.79 1.78 3.79 5.58
e e e e e e d d c b a c b a a
14 16 -- -- 0.68 1.20 -- -- 0.79 1.36 -- 0.08 1.16 1.92 0.17 1.08 2.88 4.48 0.35 1.33 3.33 5.10
f f f f f e d d c d c a
24 -- -- 0.13 0.60 -- -- 0.21 0.73 -- -- 0.48 1.18 -- 0.26 2.05 3.59 -- 0.52 2.49 4.21
f e f e e e d d c b a c b a a
12 -- -- 0.57 0.98 -- -- 0.66 1.12 -- 0.09 0.98 1.58 0.18 1.00 2.57 3.97 0.35 1.26 3.03 4.63
f f f f f e d d c d c a
16 16 -- -- 0.26 0.66 -- -- 0.34 0.77 -- -- 0.60 1.18 -- 0.51 2.07 3.44 -- 0.75 2.52 4.08
f f f e d d c
24 -- -- -- 0.11 -- -- -- 0.19 -- -- -- 0.48 -- -- 1.19 2.48 -- -- 1.60 3.09
 ESR-2361 | Most Widely Accepted and Trusted Page 18 of 20

TABLE 11—COMBINED LATERAL AND AXIAL LOADS - ALLOWABLE AXIAL LOAD (kips) WITH 25 psf LATERAL LOAD

350S162- 362S162- 400S162- 550S162- 600S162-

MAX.
WALL 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi
STUD
HEIGHT
SPACING Stud Thickness (mils)
(ft)
(in)
33 43 54 68 33 43 54 68 33 43 54 68 33 43 54 68 33 43 54 68
a a a a a a a a a a a a a a a a a a a a
12 0.97 1.68 3.17 4.27 1.04 1.78 3.36 4.57 1.23 2.05 3.85 5.37 1.79 2.82 5.09 6.93 1.87 2.89 5.14 6.99
b a a a a a a a a a a a a a a a a a a a
8 16 0.66 1.36 2.87 3.96 0.73 1.46 3.05 4.25 0.93 1.74 3.55 5.06 1.54 2.59 4.87 6.72 1.64 2.69 4.94 6.80
d c b a c b a a b a a a a a a a a a a a
24 0.09 0.76 2.30 3.38 0.16 0.86 2.48 3.66 0.37 1.15 2.98 4.45 1.07 2.14 4.44 6.30 1.21 2.28 4.56 6.43
b a a a b a a a a a a a a a a a a a a a
12 0.67 1.33 2.69 3.70 0.74 1.44 2.89 3.99 0.94 1.72 3.41 4.84 1.56 2.59 4.86 6.73 1.68 2.71 4.96 6.82
d b a a c b a a b a a a a a a a a a a a
9 16 0.33 0.96 2.34 3.34 0.39 1.06 2.54 3.62 0.59 1.35 3.06 4.45 1.26 2.31 4.58 6.45 1.40 2.45 4.71 6.57
d c b d c b c b a a a a a a a a a
24 -- 0.29 1.71 2.68 -- 0.39 1.89 2.94 -- 0.66 2.39 3.73 0.68 1.76 4.04 5.91 0.86 1.95 4.22 6.09
d c a a c b a a b a a a a a a a a a a a
12 0.39 0.99 2.21 3.11 0.46 1.09 2.42 3.40 0.65 1.38 2.95 4.26 1.32 2.34 4.55 6.47 1.46 2.51 4.75 6.61
e d c b d d c a d b a a a a a a a a a a
10 16 0.02 0.59 1.84 2.72 0.08 0.68 2.03 2.99 0.26 0.96 2.54 3.82 0.96 2.00 4.21 6.13 1.13 2.19 4.44 6.30
d d d c d c b b a a a a a a a
24 -- -- 1.17 2.02 -- -- 1.34 2.26 -- 0.20 1.81 3.01 0.29 1.35 3.56 5.46 0.48 1.58 3.84 5.71
e d c d d c d d c b a a a a a a a a
12 -- 0.39 1.37 2.06 -- 0.47 1.54 2.29 0.13 0.72 2.03 3.06 0.79 1.78 3.82 5.61 0.97 2.01 4.20 6.09
e d e e d e d c c a a a b a a a
12 16 -- -- 0.99 1.65 -- 0.03 1.13 1.86 -- 0.25 1.58 2.56 0.34 1.33 3.36 5.13 0.53 1.58 3.77 5.64
f e f e e e c b a b a a
24 -- -- 0.32 0.94 -- -- 0.43 1.11 -- -- 0.78 1.70 -- 0.50 2.51 4.24 -- 0.76 2.94 4.79
e e e e e e d d b a a c a a a
12 -- -- 0.76 1.28 -- -- 0.87 1.45 -- 0.18 1.26 2.02 0.28 1.19 2.99 4.59 0.45 1.44 3.44 5.21
f e f e e e d c b c b a
14 16 -- -- 0.39 0.89 -- -- 0.48 1.04 -- -- 0.81 1.54 -- 0.66 2.45 4.02 -- 0.91 2.90 4.64
f f f f d d d c
24 -- -- -- 0.21 -- -- -- 0.32 -- -- 0.03 0.70 -- -- 1.49 2.98 -- -- 1.92 3.60
f f f f e e d c b c b a
12 -- -- 0.34 0.73 -- -- 0.41 0.85 -- -- 0.68 1.27 -- 0.63 2.19 3.56 -- 0.87 2.64 4.21
f f f f f e d d d d c
16 16 -- -- -- 0.37 -- -- 0.05 0.47 -- -- 0.25 0.81 -- 0.06 1.61 2.94 -- 0.29 2.04 3.57
f e e e d
24 -- -- -- -- -- -- -- -- -- -- -- 0.02 -- -- 0.60 1.84 -- -- 0.98 2.42
 ESR-2361 | Most Widely Accepted and Trusted Page 19 of 20

TABLE 12—COMBINED LATERAL AND AXIAL LOADS - ALLOWABLE AXIAL LOAD (kips) WITH 30 psf LATERAL LOAD

350S162- 362S162- 400S162- 550S162- 600S162-

MAX.
WALL 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi 33 ksi 50 ksi
STUD
HEIGHT
SPACING Stud Thickness (mils)
(ft)
(in)
33 43 54 68 33 43 54 68 33 43 54 68 33 43 54 68 33 43 54 68
a a a a a a a a a a a a a a a a a a a a
12 0.78 1.49 2.99 4.08 0.85 1.59 3.17 4.38 1.05 1.86 3.67 5.18 1.64 2.68 4.96 6.80 1.73 2.77 5.02 6.88
c b a a b a a a a a a a a a a a a a a a
8 16 0.43 1.11 2.64 3.72 0.50 1.21 2.82 4.01 0.70 1.50 3.32 4.81 1.35 2.41 4.70 6.55 1.47 2.53 4.79 6.65
d c a c b a c b a a a a a a a a a a
24 -- 0.42 1.99 3.05 -- 0.52 2.16 3.32 0.05 0.81 2.66 4.10 0.79 1.88 4.19 6.05 0.95 2.05 4.33 6.21
c b a a c a a a b a a a a a a a a a a a
12 0.46 1.11 2.48 3.48 0.53 1.21 2.68 3.77 0.73 1.49 3.20 4.60 1.38 2.42 4.69 6.56 1.51 2.56 4.81 6.67
d c b a d c b a c b a a a a a a a a a a
9 16 0.07 0.69 2.08 3.06 0.13 0.78 2.27 3.34 0.33 1.07 2.78 4.16 1.03 2.09 4.36 6.23 1.18 2.25 4.52 6.38
d c d d c d c b a a a a a a a a
24 -- -- 1.37 2.31 -- 0.02 1.54 2.57 -- 0.28 2.02 3.33 0.35 1.44 3.72 5.59 0.54 1.65 3.94 5.81
d c b a d c b a c b a a a a a a a a a a
12 0.17 0.74 1.99 2.88 0.23 0.84 2.18 3.15 0.41 1.12 2.70 3.99 1.10 2.14 4.35 6.26 1.26 2.32 4.57 6.43
d d c d c b c b a a a a a a a a a
10 16 -- 0.29 1.56 2.43 -- 0.38 1.74 2.69 -- 0.64 2.24 3.48 0.69 1.74 3.95 5.85 0.86 1.94 4.20 6.06
e d e d d c b a a b a a a
24 -- -- 0.81 1.63 -- -- 0.96 1.86 -- -- 1.40 2.57 -- 0.97 3.18 5.07 0.11 1.22 3.49 5.36
e e d e d d d d c b a a a a a a a
12 -- 0.13 1.13 1.81 -- 0.20 1.29 2.03 -- 0.43 1.75 2.76 0.52 1.51 3.54 5.32 0.70 1.75 3.94 5.82
e e e e e d b a a c a a a
12 16 -- -- 0.71 1.35 -- -- 0.84 1.55 -- -- 1.25 2.20 -- 0.99 3.01 4.76 0.19 1.24 3.43 5.29
f f f f e d c b c b a
24 -- -- -- 0.56 -- -- 0.05 0.71 -- -- 0.36 1.23 -- 0.04 2.04 3.74 -- 0.31 2.47 4.31
f e f e e d c b a c b a a
12 -- -- 0.53 1.04 -- -- 0.64 1.19 -- -- 0.98 1.73 -- 0.86 2.66 4.24 0.14 1.12 3.11 4.87
f f f f f e d d c d c a
14 16 -- -- 0.13 0.60 -- -- 0.21 0.73 -- -- 0.48 1.18 -- 0.26 2.05 3.59 -- 0.52 2.49 4.21
f e d d c
24 -- -- -- -- -- -- -- -- -- -- -- 0.25 -- -- 0.96 2.41 -- -- 1.38 3.02
f f f f f e e d c d c b
12 -- -- 0.13 0.51 -- -- 0.19 0.62 -- -- 0.42 0.98 -- 0.28 1.83 3.18 -- 0.51 2.28 3.82
f f f e d d c
16 16 -- -- -- 0.11 -- -- -- 0.19 -- -- -- 0.48 -- -- 1.19 2.48 -- -- 1.60 3.09
f e e e
24 -- -- -- -- -- -- -- -- -- -- -- -- -- -- 0.06 1.26 -- -- 0.40 1.80
ESR-2361 | Most Widely Accepted and Trusted Page 20 of 20

TABLE 13—STUDS FOR USE WITH THE 2009 IRC

IRC MEMBER DESIGNATION

t 350S162-t 550S162-t
EQUIVALENT METAL FORMING TECHNOLOGIES MEMBER DESIGNATION
33 350S162-33 550S162-33
43 350S162-43 550S162-43
54 350S162-54 550S162-54
68 350S162-68 550S162-68

TABLE 14—MANUFACTURING LOCATIONS

FRAMECAD Ltd.
Douglass Colony Group, Inc. George M. Raymond Co.
Glen Innes/ St. John, Auckland
Commerce City, CO 80022 Las Vegas, NV 89118
New Zealand

Volstrukt, LLC Centerline Prefab, LLC BLUvera, LLC

Austin, TX 78728 Grand Rapids, MI 49548 Northwood, IA 50459

F.L. Crane and Sons, Inc. Network-Framing

C.J. Coakley Co., Inc.
Ocean Spring, MS 39564 Solutions, LLC
Merrifield, VA 22031
Plainville, CT 06062

Frameland Industries, LLC

- -
Apopka, FL 32703

FIGURE 1—TYPICAL STUD AND

TRACK DETAILS
FIGURE 2—SWAGED END DETAILS