NOTE: This guide covers only the most common

situations. Please refer to the full User

Manual on the Router CD-ROM if your
network LAN has any of the following:
• another connected router
• an existing DHCP Server
• PCs using Fixed (Static) IP Addresses

802.11g Wireless
Router
Multi-function wireless router
with 4-Port Fast Ethernet switch
WEP-72104G
vers.2

User’s Guide
 Table of Contents
CHAPTER 1: INTRODUCTION..............................................................................2
Wireless Router Features ...................................................................................2
Package Contents .............................................................................................4
Physical Details................................................................................................5
About the Operation Mode................................................................................7
CHAPTER 2: INSTALLATION ..............................................................................8
Requirements ...................................................................................................8
Procedure ........................................................................................................8
CHAPTER 3: SETUP .............................................................................................9
Overview .........................................................................................................9
Configuration Program .....................................................................................9
Setup Wizard................................................................................................. 11
Configuration via Web ................................................................................... 14
CHAPTER 4: PC CONFIGURATION .................................................................... 35
Overview ....................................................................................................... 35
Windows Clients ............................................................................................ 35
Macintosh Clients........................................................................................... 47
Linux Clients................................................................................................. 47
Other Unix Systems ........................................................................................ 47
Wireless Station Configuration........................................................................ 48

APPENDIX A TROUBLESHOOTING ....................................................... 49

Overview ....................................................................................................... 49
General Problems........................................................................................... 49
Internet Access ............................................................................................... 49
Wireless Access............................................................................................... 50

APPENDIX B ABOUT WIRELESS LANS.................................................. 51

Modes ........................................................................................................... 51
BSS .............................................................................................................. 51
Channels ....................................................................................................... 51
WEP............................................................................................................. 52
Wireless LAN Configuration ........................................................................... 52
APPENDIX C SPECIFICATIONS ......................................................................... 53
Multi-Function Wireless Router....................................................................... 53
Wireless Interface ........................................................................................... 53
Regulatory Approvals..................................................................................... 54
Chapter 1: Introduction
Congratulations on the purchase of your new Unicom 802.11g Wireless Router. Unicom’s
Wireless Router is a multi-function device providing the following services:
• Shared Broadband Internet Access for all LAN users.
• 4-Port Switching Hub for 10Base-T or 100Base-T connections.
• Wireless Access Point for 802.11b and 802.11g Wireless Stations.

Wireless Router Features

Unicom's 802.11g Wireless Router incorporates many advanced features, carefully designed to
provide sophisticated functions while being easy to use.

Internet Access Features

• Shared Internet Access. All users on the LAN or WLAN can access the Internet
through the Wireless Router, using only a single external IP Address. The local (invalid)
IP Addresses are hidden from external sources. This process is called NAT (Network
Address Translation).
• DSL & Cable Modem Support. The Wireless Router has a 10/100Base-T Ethernet
port for connecting a DSL or Cable Modem. All popular DSL and Cable Modems are
supported. SingTel RAS and Big Pond (Australia) login support is also included.
• PPPoE, and PPTP. The Internet (WAN port) connection supports PPPoE (PPP over
Ethernet), PPTP (Peer-to-Peer Tunneling Protocol), as well as "Direct Connection" type
services. Unnumbered IP with PPPoE is also supported.
• Fixed or Dynamic IP Address. On the Internet (WAN port) connection, the Wireless
Router supports both Dynamic IP Address (IP Address is allocated on connection) and
Fixed IP Address.

Advanced Internet Functions

• Communication Applications. Support for Internet communication applications, such
as interactive Games, Telephony, and Conferencing applications, which are often difficult
to use when behind a Firewall, is included.
• Special Internet Applications. Applications that use non-standard connections or port
numbers are normally blocked by the Firewall. Application support is provided allowing
such applications to be used normally.

2
• Virtual Servers. This feature allows Internet users to access Internet servers on your
LAN. The required setup is quick and easy.
• DDNS Support. DDNS (Dynamic DNS) allows Internet users to connect to Virtual
Servers on your LAN using a domain name, even if your IP address is not fixed.
• DMZ. For each WAN (Internet) IP address allocated to you, only one (1) PC on your
local LAN can be configured to allow unrestricted 2-way communication with Servers or
individual users on the Internet. This provides the ability to run programs that are
incompatible with Firewalls.
• URL Filter. Use the URL Filter to block access to undesirable Web sites by LAN users.
• Internet Access Log. See which Internet connections have been made.
• Access Control. Using the Access Control feature, you can assign LAN users to
different groups, and determine which Internet services are available to each group.
• VPN Pass through Support. PCs with VPN (Virtual Private Networking) software
using PPTP, L2TP and IPSec are transparently supported - no configuration is required.

Wireless Features
• Standards Compliant. The Wireless Router complies with the IEEE802.11g (DSSS)
specifications for Wireless LANs.
• Supports both 802.11b and 802.11g Wireless Stations. The 802.11g standard
provides for backward compatibility with the 802.11b standard, so that both 802.11b and
802.11g Wireless stations can be used simultaneously.
• Speeds to 54Mbps. All speeds up to the 802.11g maximum of 54Mbps are supported.
• WEP support. Support for WEP (Wired Equivalent Privacy) is included. Key sizes of
64 Bit and 128 Bit are supported.
• Wireless MAC Access Control. The Wireless Access Control feature can check the
MAC address (hardware address) of Wireless stations to ensure that only trusted Wireless
Stations can access your LAN.
• Simple Configuration. If the default settings can be changed quickly and easily.

LAN Features
• 4-Port Switching Hub. The Wireless Router incorporates a 4 Port 10/100Base-T
switching hub, making it easy to create or extend your LAN.
• DHCP Server Support. Dynamic Host Configuration Protocol provides a dynamic IP
address to PCs and other devices upon request. The Wireless Router can act as a DHCP
Server for devices on your local LAN and WLAN.

Configuration & Management

• Easy Setup. Use your WEB browser from anywhere on the LAN or WLAN for
configuration.
• Configuration File Upload/Download. Save (download) the configuration data from
the Wireless Router to your PC, and restore (upload) a previously saved configuration file
to the Wireless Router.
• Remote Management. The Wireless Router can be managed from any PC on your
LAN. If an Internet connection exists, the router can also be configured via the Internet.
• Network Diagnostics. The Wireless Router can perform a Ping or DNS lookup.
• UPnP Support. UPnP (Universal Plug and Play) allows automatic discovery and
configuration of the Wireless Router. UPnP is by supported by Windows ME, XP, or
later.

3
Security Features
• Password-protected Configuration. Optional password protection is provided to
prevent unauthorized users from modifying the configuration data and settings.
• Wireless LAN Security. WEP (Wired Equivalent Privacy) is supported, as well as
Wireless access control to prevent unknown wireless stations from accessing your LAN.
• NAT Protection. An intrinsic side effect of NAT (Network Address Translation)
technology is that by allowing all LAN users to share a single IP address, the location and
even the existence of each PC is hidden. From the external viewpoint, there is no network,
only a single device - the Wireless Router.
• Protection against DoS attacks. DoS (Denial of Service) attacks can flood your
Internet connection with invalid packets and connection requests, using so much
bandwidth and so many resources that Internet access becomes unavailable. The Wireless
Router incorporates protection against DoS attacks.

Package Contents
The following items are included:
• The Wireless Router Unit
• Power Adapter
• Quick Installation Guide
• CD-ROM containing the online manual.
If any of the above items are damaged or missing, please contact your dealer immediately.

4
Physical Details

Front-mounted LEDs

Figure 1: Front Panel

Power LED On - Power on.

Off - No power.
Internet LED On - Connection to the Broadband Modem attached to the WAN
(Internet) port is established.
Off - No connection to the Broadband Modem.
Flashing - Data is being transmitted or received via the WAN port.
WLAN LED On - Wireless connection available; Wireless Access Point is ready for
use.
Off - No Wireless connection available.
Flashing - Data is being transmitted or received via the Wireless access
point. Data includes "network traffic" as well as user data.
LAN LEDs For each port, there are 2 LEDs
• Link/Act light
On - Corresponding LAN (hub) port is active.
Off - No active connection on the corresponding LAN (hub) port.
Flashing - Data is being transmitted or received via the
corresponding LAN (hub) port.
• 100 light
On - Corresponding LAN (hub) port is using 100Base-T.
Off - Corresponding LAN (hub) port connection is using 10Base-T,
or no active connection.

5
Rear Panel

Figure 2: Rear Panel

Power port Connect the supplied power adapter here.

10/100Base-T Use standard LAN cables (RJ45 connectors) to connect your PCs to
LAN port these ports.
If required, any port can be connected to another hub. Any LAN port
will automatically function as an "Uplink" port when necessary.
Internet port Connect the DSL or Cable Modem here. If your modem came with a
(10/100Base-T) cable, use the supplied cable. Otherwise, use a standard LAN cable.
Reset Button This button has two (2) functions:
• Reboot. When pressed within 3~5 seconds, the power LED
lights amber. When released, the Wireless Router will reboot
(restart).
• Clear All Data. This button can also be used to clear ALL data
and restore ALL settings to the factory default values.

To Clear All Data and restore the factory default values:

1. After Power On.
2. Hold the Reset Button down.
3. Keep holding the Reset Button more than 5 seconds, until the
Amber LED has flashed.
4. Release the Reset Button. The Wireless Router is now using the
factory default values.

6
About the Operation Mode

AP Mode
When acting as an access point, this device connects all the remote stations (Desktop/notebook
PC with wireless network adapter) to a wired network. All stations can have Internet access
provided the Access Point has an Internet connection.

Bridge Mode
The WDS (Wireless Distributed System) function lets this access point act as a wireless LAN
access point and repeater at the same time. Users can use this feature to build up a large
wireless network in a large space like airports, hotels and schools …etc. This feature is also
useful when users want to bridge networks between buildings where it is impossible to deploy
network cable connections between these buildings.

Repeater
Refer to the illustration below. While acting as a Bridge, AP1 (Station 1) and AP2 (Station 2)
can communicate with each other through wireless interface (with WDS). Thus Station 1 can
communicate with Station 2 and both Station 1 and Station 2 are able to access the Internet
even if only one of the stations has the Internet connection.
To set the operation mode to Bridge, please go to “Wireless
Basic Settings”, in the
“Mode” field click the down arrow  to select AP mode. And go to “Wireless
WDS
Settings” to enable WDS.

7
Chapter 2: Installation
Requirements
• Network cables. Use standard 10/100Base-T network (UTP) cables with RJ45 connectors.
• TCP/IP protocol must be installed on all PCs.
• For Internet Access, an Internet Access account with an ISP and either a DSL or Cable
modem (for WAN port usage)
• To use the Wireless Access Point, all Wireless devices must be compliant with the
IEEE802.11b or IEEE802.11g specifications.

Procedure

1. Choose an Installation Site

• Select a suitable place on the network to install the Wireless Router.
Ensure both the Wireless Router and the DSL/Cable modem are powered OFF.
2. Connect LAN Cables
• Use standard LAN cables to connect PCs to the Switching Hub ports on the Wireless
Router. Both 10Base-T and 100Base-T connections can be used simultaneously.
• If required, connect any port to a normal port on another Hub, using a standard LAN
cable. Thanks to MDI/MDIX, any LAN port on the Wireless Router will automatically
function as an "Uplink" port when required.
3. Connect WAN Cable
• Connect the DSL or Cable modem to the WAN port on the Wireless Router. Use the cable
supplied with your DSL/Cable modem. If no cable is supplied, use a standard RJ45 cable.
4. Power Up
• Power on the Cable or DSL modem.
• Connect the supplied power adapter to the Wireless Router and power up.
Use only the power adapter provided. Using a different one may cause hardware damage
5. Check the LEDs
• The Power LED should be ON.
• The Status LED should flash, then turn off. If it stays on, there is a hardware error.
• For each LAN (PC) connection, the LAN Link/Act LED should be ON (provided the PC
is also ON.)
• The WAN LED should be ON.
• The WLAN LED should be ON
For more information, refer to Front-mounted LEDs in Chapter 1.

8
Chapter 3: Setup
Overview
This chapter describes the setup procedure for:
• Internet Access
• LAN configuration
• Wireless setup
• Assigning a Password to protect the configuration data.
PCs on your local LAN may also require configuration. For details, see Chapter 4 - PC
Configuration.
Other configuration may also be required, depending on which features and functions of the
Wireless Router you wish to use. Use the table below to locate detailed instructions for the
required functions.

Configuration Program
The Wireless Router contains an HTTP server. This enables you to connect to it and configure
it using your Web Browser. Your Browser must support JavaScript.
The configuration program has been tested on the following browsers:
• Netscape v4.08 or later
• Internet Explorer v4 or later

Preparation
Before attempting to configure the Wireless Router, please ensure that:
• Your PC can establish a physical connection to the Wireless Router. The PC and the
Wireless Router must be directly connected (using the Hub ports on the Wireless Router)
or on the same LAN segment.
• The Wireless Router must be installed and powered ON.
• If the Wireless Router's default IP Address (192.168.1.254) is already used by another
device, the other device must be turned OFF until the Wireless Router is allocated a new
IP Address during configuration.

Using UPnP
If your Windows system supports UPnP, an icon for the Wireless Router will appear in the
system tray notifying you that a new network device has been found and offering to create a
new desktop shortcut to the newly-discovered device.
• Unless you intend to change the IP Address of the Wireless Router, you can accept the
desktop shortcut.
• Whether you accept the desktop shortcut or not, you can always find UPnP devices in My
Network Places (previously called Network Neighborhood).
• Double-click the icon for the Wireless Router (either on the Desktop or in My Network
Places) to start the configuration. Refer to the following section, Setup Wizard, for details
of the initial configuration process.

9
Using your Web Browser
To establish a connection from your PC to the Wireless Router:
1. After installing the Wireless Router in your LAN, start your PC. If your PC is already
running, restart it.
2. Start your WEB browser.
3. In the Address box, enter "HTTP://" and the IP Address of the Wireless Router. The
Wireless Router's default IP Address is as follows:
HTTP://192.168.1.254
No username and password are required for the first login (default setting). However, you can
assign a set of username and password for future security. See the Password Setup section later
in this chapter for details.

If you can't connect

If the Wireless Router does not respond, check the following:
• The Wireless Router is properly installed, LAN connection is OK, and it is
powered ON. You can test the connection by using the "Ping" command:
• Open the MS-DOS window or command prompt window.
• Enter the command:
ping 192.168.1.254
If no response is received, either the connection is not working, or your
PC's IP address is not compatible with the Wireless Router's IP Address.
(See next item.)
• If your PC is using a fixed IP Address, its IP Address must be within the
range 192.168.1.1 to 192.168.1.253 to be compatible with the Wireless
Router's default IP Address of 192.168.1.254. Also, the Network Mask must
be set to 255.255.255.0. See Chapter 4 - PC Configuration for details on
checking your PC's TCP/IP settings.
• Ensure that your PC and the Wireless Router are on the same network
segment. (If you don't have a router, this must be the case.)
• Ensure you are using the wired LAN interface. The Wireless interface can only
be used if its configuration matches your PC's wireless settings.

10
Setup Wizard
The Setup Wizard provides brief and basic configuration of this device, you may enter each
screen to change the default settings. For more detailed settings, you may refer to the
“Configuration via Web” section.
1. View the listed configuration items and click Next to continue.

2. Configure Time Zone and NTP server by enabling NTP client update. Click Next to
continue.

3. Configure the parameters for area network (If you want to change the default parameters) by
entering New IP Address and Subnet Mask.

4. Change the access method (Static IP, DHCP, PPPoE or PPTP) by selecting from the pull-
down menu. Click Next to continue.

11
5. Configure the parameters for wireless LAN clients. Check the “Disable Access Point” to
disable the settings of this screen. Click Next to continue.

6. Manage your wireless network security by selecting the encryption type (None, WEP and
WPA (TKIP)) from the pull-down menu. Click Finish to exit Set Wizard screen.

12
Common Connection Types

Cable Modems
Type Details ISP Data required
Dynamic Your IP Address is allocated Usually, none. However some
IP Address automatically when you ISP's may require you to use a
connect to you ISP. particular Hostname, Domain
name, or MAC (physical) address.
Static Your ISP allocates a IP Address allocated to you.
(Fixed) permanent IP Address to you. Some ISP's may also require you
IP Address to use a particular Hostname,
Domain name, or MAC (physical)
address.

DSL Modems
Type Details ISP Data required
Dynamic Your IP Address is allocated None.
IP Address automatically when you
connect to you ISP.
Static (Fixed) Your ISP allocates a Permanent IP Address allocated.
IP Address permanent IP Address to you.
PPPoE You connect to the ISP only User name and password.
when required. The IP address
is usually allocated
automatically.
PPTP Mainly used in Europe. • PPTP Server IP Address.
You connect to the ISP only • User name and password.
when required. The IP address • IP Address allocated to
is usually allocated you, if Static (Fixed).
automatically but may be
Static (Fixed).

Other Modems (e.g. Broadband Wireless)

Type Details ISP Data required
Dynamic Your IP Address is allocated None.
IP Address automatically when you connect
to you ISP.
Static (Fixed) Your ISP allocates a permanent Permanent IP Address
IP Address IP Address to you. allocated.

13
Configuration via Web

LAN Interface Setup

IP Address Default: 192.168.1.254 (this is the local address of this Router)

Subnet Mask Default: 255.255.255.0

DHCP Disable: Disables this Router from distributing IP Addresses

Server: Enables this Router to distribute IP Addresses (DHCP
Server). The following field will be activated to enter the
starting IP Address

DHCP Client Range The starting address of this local IP network address pool.
The pool is a piece of continuous IP address segment. Keep the
default value “192.168.1.1” It should work in most cases.
• Maximum: 253. Default value 253 should work
in most cases.
Note: If “Continuous IP address poll starts” is set at
192.168.1.1 and the “Number of IP address in pool” is 253,
the device will distribute IP addresses from 192.168.1.1 to
192.168.1.253 to all the computers in the network that request
IP addresses from DHCP server (Router)

Show Client Click to show Active DHCP Client table.

Save After completing the settings on this page, click Save to save
the settings.

Reset Click Reset to restore to default values.

14
Password Setup

New Password Maximum input is 36 alphanumeric characters (case sensitive)

Confirmed Password Key in the password again to confirm.

Save After completing the settings on this page, click Save to save
the settings.

Reset Click Reset to clear settings.

Status

Internet Shows the Internet connection status

LAN Shows the Local area network information

System Briefly shows the device name and firmware information

Connection Details Click to show more details of the internet connection

System Data Click to show the detailed information of the system

Refresh Screen Click to refresh all the data

15
Wireless

Wireless basic Settings

Disable Access Point Check to disable the AP function.

The wireless (WLAN) LED on front panel will remain OFF if
the Wireless interface is disabled.

Band You can choose one of the following modes:

 2.4GHz (B): 802.11b supported rate only.

 2.4GHz (G): 802.11g supported rate only.

 2.4GHz (B+G): 802.11b supported rate and 802.11g

supported rate.

The default is 2.4GHz (B+G) mode.

SSID Shows the SSID name.

Channel Number Select the router’s wireless channel (from 1 to 11).

Associated Clients Click to show all the listed active clients.

Save After completing the settings on this page, click Save to save
the settings.

Reset Click Reset to restore to default values.

16
Wireless Advanced Settings

Authentication Open System: If your access point/wireless router is using "Open

Type " authentication, then the wireless adapter will need to be set to the
same authentication type.
Shared Key: Shared Key is when both the sender and the
recipient share a secret key.
Auto: Select Auto Switch for the adapter to automatically select
the appropriate authentication.

Preamble Type A preamble is a signal used in wireless environments to

synchronize the transmission timing including Synchronization
and Start frame delimiter. (Note: If you want to change the
Preamble type into Long or Short, please check the setting of
AP.)
Broadcast SSID Enable: This wireless AP will broadcast its SSID to all stations.
Disable: This wireless AP will not broadcast its SSID to stations. If
stations want to connect to this wireless AP, its SSID should be known
in advance to make a connection.

Save After completing the settings on this page, click Save to save the
settings.

Reset Click Reset to restore to default values.

Security
Here you can configure the security of your wireless network. Selecting different methods will
enable you to have different levels of security. Please note that using any encryption by which
data packets are encrypted before transmission to prevent undesired eavesdropping, there may
be a significant degradation of the data throughput on the wireless link.
Note: This security function is only enabled under AP mode and Repeater mode.
Encryption: None (Encryption is set to None by default)
If Use 802.1x Authentication is selected, the RADIUS Server will proceed to check the
802.1x Authentication.

17
Encryption: WEP
If WEP is selected, users must Set WEP keys either manually or select to Use 802.1x
Authentication to make the RADIUS server issue the WEP key dynamically.

• Clicking Set WEP Keys will prompt you to set 64bit or

SET WEP KEY 128bit Encryption.
• Select HEX if you are using hexadecimal numbers (0-9,
or A-F). Select ASCII if you are using ASCII characters
(case-sensitive).
• Ten hexadecimal digits or five ASCII characters are
needed if 64-bit WEP is used; 26 hexadecimal digits or
13 ASCII characters are needed if 128-bit WEP is used.

Encryption: WPA (TKIP)

WPA (TKIP): If WPA is selected, users must select either Enterprise (RADIUS) or
Personal (Pre-shared Key) Authentication modes.

Pre-shared Key Pre-Shared-Key serves as a password. Users may key in a 1

to 63 character string to set the password or leave it blank in
which the 802.1x Authentication will be activated. Make sure
the same password is used on the client's end.
There are two Pre-shared key formats, i.e. Passphrase and
Hex. If Hex is selected, users will have to enter a 64 characters
string. For easier configuration, the Passphrase (at least 8

18
 characters) format is recommended.

Group Key Life Time Enter the number of seconds that will elapse before the group
key changes automatically. The default is 86400 seconds.

Enable Pre- The two most important features standardized through

Authentication 802.11i/WPA2 beyond WPA are: pre-authentication, which
enables secure fast roaming without noticeable signal latency.
Pre-authentication provides a way to establish a PMK security
association before a client associates. The advantage is that the
client reduces the time that it is disconnected to the network.

Authentication RADIUS Port: Enter the RADIUS Server’s port number provided by
Server your ISP. The default is 1812.
IP Address: Enter the RADIUS Server’s IP Address provided
by your ISP.
Password: Enter the password that the AP shares with the
RADIUS Server.

Save Press to save the new settings on the screen.

Reset Press to discard the current settings.

Site Survey
Site survey displays all the active Access Points and IBSS in the neighborhood.

Refresh Click Refresh to get the latest information.

Connect Click Connect to make a wireless connection.

WDS Settings

19
Enable WDS Check Enable WDS to enable the WDS function.

Add WDS AP MAC Address: Enter the Wireless SSID of the wireless AP that
you want to connect with. To check your wireless router’s MAC
address, please go to Status and then click the System Data
button to find your MAC address.
Comment: Enter a description for the device.
Set Security Enable the WDS function and then click to set the WDS
security. For detailed security setup, please refer to the Wireless
Security mentioned previously.

Show Statistics Click to show the current WDS AP table.

Save Click Save to save the current settings.

Reset Click Reset to clear and reset.

Current WDS AP List Click Current WDS AP List to show the current WDS AP
information.

Delete Selected Click Delete Selected to delete the selected items.

Delete All Click Delete All to delete all the items.

Reset Click Reset to reset.

Trusted Stations
The Trusted Stations screen allows you to configure this device to give exclusive access to up
to 20 devices. Every Ethernet device has a unique MAC (Media Access Control) address. The
MAC address is assigned at the factory and consists of six pairs of hexadecimal characters, for
example, 00:A0:C5:00:00:02. You need to know the MAC address of the devices to configure
this screen.

20
Wireless Access Control Mode Select the Access Control Mode from the pull-down menu.
Disable: Select to disable Wireless Access Control Mode.
Allow Listed: Only the stations shown in the table can
associate with the AP.

MAC Address Enter the MAC addresses of the wireless stations that are
to be allowed or denied access to this wireless router in
these address fields. Enter the MAC addresses in a valid
MAC address format, that is, a six hexadecimal character
pairs. i.e., 12:34:56:78:9a:bc.
Description Enter a descriptive name so you know which device the
MAC address is associated with.
Current Access Control List Shows the current access control list.

Delete Selected Select the MAC Address(es) you want to delete and then
click the Delete Selected button.

Delete All Click to delete all the MAC Address(es) listed.

Save After completing the settings on this page, click Save to

save the settings.

Reset Click Reset to restore to default values.

Current Access Control List Shows the current access control information.

Delete Selected Click Delete Selected to delete all selected items.

Delete All Click Delete All to delete al items.

Reset Click Reset to rest.

21
Advanced

WAN Port

WAN Access Type Select the WAN access type (Static IP, DHCP, PPPoE and
PPTP) from the pull-down menu.

DNS 1-3 Enter the DNS server IP address(es) provided by your ISP
or you can specify your own preferred DNS server IP
address(es).
DNS 1 and DNS 2 servers are optional. You can enter
another DNS server’s IP address as a backup. DNS 1 and
DNS 2 servers will be used when the DNS 1 server fails.

Clone MAC Address Your ISP may require a particular MAC address in order
for you to connect to the Internet. This MAC address is
the PC’s MAC address that your ISP had originally
connected your Internet connection to. Type in this Clone
MAC address in this section to replace the WAN MAC
address with the MAC address of that original PC.
Enable uPNP Check to enable the listed functions.
Enable Ipsec pass through
on VPN connection
Enable L2TP pass through
on VPN connection

Save After completing the settings on this page, click Save to

save the settings.

Reset Click Reset to restore to default values.

22
Access Control
This screen allows you to block access to specified Internet services based on the
port number used. This can be used restrict Internet access to only certain
applications or to block applications you feel may be harmful.

Enable Access Control Select to enable Access Control function.

Select Services to Block This lists all defined Services. Select the Services you wish to
block.

Port Range For TCP and UDP Services, enter the beginning of the range of
port numbers used by the service. If the service uses a single
port number, enter it in both the start and finish fields.

Protocol Select the protocol (TCP, UDP or Both) used to the remote
system or service.

Description You may key in a description for port range.

Save After completing the settings on this page, click Save to save
the settings.

Reset Click Reset to restore to default values.

Current Blocked Table Shows the current blocked information.

Delete Selected Click Delete Selected to delete selected items.

Delete All Click Delete All to delete all the items.

Reset Click Reset to rest

Dynamic DNS
Dynamic DNS allows you to update your current dynamic IP address with one or
many dynamic DNS services so that anyone can contact you (in NetMeeting, CU-
SeeMe, etc.). You can also access your FTP server or Web site on your own
computer using a domain name (for instance myhost.dhs.org, where my host is a
name of your choice) that will never change instead of using an IP address that
changes each time you reconnect. Your friends or relatives will always be able to
call you even if they don't know your IP address.

23
First of all, you need to have registered a dynamic DNS account with either
www.dyndns.org or www.tzo.com. This is for those with a dynamic IP from their
ISP or DHCP server that would still like to have a domain name. The Dynamic
DNS service provider will give you a password or key.

Enable DDNS Check to enable DDNS function.

This free service is very useful when combined with the Virtual
Server feature. It allows Internet users to connect to your Virtual
Servers using a URL, rather than an IP Address. This also solves the
problem of having a dynamic IP address. With a dynamic IP address,
your IP address may change whenever you connect, which makes it
difficult to connect to.

Service Provider • Select the desired DDNS Service Provider from the list.
• Details of your DDNS account (Name, password, Domain name)
must then be entered and saved on this screen.
• This device will then automatically ensure that your current IP
Address is recorded by the DDNS Service Provider.
• From the Internet, users will now be able to connect to your
Virtual Servers (or DMZ PC) using your Domain name.

Domain Name Apply for a Domain Name and ensure it is allocated to you.

User Name/Email Enter your Username for the DDNS Service.

Password/key Enter your current password for the DDNS Service.

Result Displays the current results from IP address registration attempts

with the DDNS provider.
Update Click Update to update the screen information.

Reset Click Reset to restore to default values.

24
DMZ
If the DMZ Host Function is enabled, it means that you set up DMZ host at a particular
computer to be openly exposed to the Internet so that some applications/software, especially
Internet/online gaming can have two-way connections. A device acting as DMZ is not
protected by this device’s firewall.

Enable DMZ If the DMZ Host Function is enabled, it means that you set up
DMZ host at a particular computer to be openly exposed to the
Internet so that some applications/software, especially
Internet/online gaming can have two-way connections.

DMZ Host IP Address Enter the IP address of a particular host in your LAN which will
receive all the packets originally going to the WAN port/Public IP
address above.

Note: You need to give your LAN PC clients a fixed/static IP

address for DMZ to work properly.
Save After completing the settings on this page, click Save to save the
settings.

Reset Click Reset to restore to default values.

25
DoS Setting
DoS (Denial of Service) attacks can flood your Internet connection with invalid packets and
connection requests, occupying so much bandwidth and so many resources that Internet access
becomes unavailable. The Wireless Router incorporates protection against DoS attacks. This
screen allows you to configure DoS protection.

Enable DoS Select to enable the DoS prevention function.

Prevention
Enable Source IP Set the threshold for the frequency of packets that are allowed to pass
Blocking Block through. The default value is 50 packets per second. You can adjust the
time (sec) value according to your need. It is recommended that you set a practical
number so that your network performance won’t be hampered.
Select All Click to select all listed items.
Clear All Click to clear all listed items.
Apply Changes Click to save the current settings.

Virtual Server
The Virtual Server function is a list of inside servers (behind NAT on the LAN), for example,
web or FTP, that you can make visible to the outside world even though NAT makes your
whole inside network appear as a single computer to the outside world. You may enter a single
port number or a range of port numbers to be forwarded and the local IP address of the desired
server. The port number identifies a service; for example, web service is on port 80 and FTP
on port 21. In some cases, such as for unknown services or where one server can support more
than one service (for example both FTP and web service), it might be better to specify a range
of port numbers. You can allocate a server IP address that corresponds to a port or a range of
ports. Many residential broadband ISP accounts do not allow you to run any server processes
(such as a Web or FTP server) from your location. Your ISP may periodically check for servers
and may suspend your account if it discovers any active services at your location. If you are
unsure, refer to your ISP.

26
Enable Virtual Servers Select to enable virtual server function.

Servers You can set up a local server with a specific port number that
represents the service (e.g. web (80), FTP (21), Telnet (23)).
When this device receives an incoming access request for this
specific port, it will be forwarded to the corresponding internal
server. You can add virtual servers by either port numbers or
by names.
Maximum 24 Server entries are allowed and each port number
can only be assigned to one IP address.

Local IP Address Enter the Local Server’s IP address.

Protocol Select the protocol (TCP, UDP or Both) used for the remote system
or service.

Port Range For TCP and UDP Services, enter the beginning of the range of
port numbers used by the service. If the service uses a single port
number, enter it in both the start and finish fields.

Description You may key in a description for the local IP address.

Save After completing the settings on this page, click Save to save the
settings.

Reset Click Reset to restore to default values.

Current Virtual Servers Shows the current virtual servers information.

Table

Delete Selected Click Delete Selected to delete all selected items.

Delete All Click Delete All to delete all the items.

Reset Click Reset to rest

27
Special Application
If you use Internet applications that use non-standard connections or port numbers, you may
find that they do not function correctly because they are blocked by the Wireless Router's
firewall. In this case, you can define those applications as "Special Applications" so that they
function properly.
You can define your Special Applications. You will need detailed information about the
application such as number of ports required; this is normally available from the supplier of
the application.
Also, note that "Incoming" on this screen refer to traffic from the client (PC) viewpoint.
You must first check Enable before you can add or edit an application.

Name Enter the application name.

Incoming Type Click the down arrow  to select the incoming application type (TCP
or UDP)
Incoming Start Type a port number or the starting port number in a range of port
Port numbers.
Incoming Finish Type a port number or the ending port number in a range of port
Port numbers.
Trigger Type Click the down arrow  to select the trigger type (TCP or UDP)
Trigger Start Enter a port number as the starting outbound port for the special
Port application defined in the preceding field.
Trigger Finish Enter a port number as the ending outbound port for the special
Port application defined in the preceding field.
Save Press to save the new settings on the screen.
Undo Press to discard all new data entered since last Save.

Ping
This screen allows you to perform a "Ping". The response messages that will appear below
can be useful in diagnosing network problems.

28
IP Address/ Enter the IP address or domain name that you want to ping.
Host name
Run Click to start pinging.
Reset Click to clear the current IP address /Host name.

Diagnostics
This screen allows you to perform a DNS lookup on any host name you enter. This can be
used to help diagnose network problems.

Domain Name/URL Enter the domain name you want to lookup.

Start Lookup Click this button to activate the DNS lookup.

Administration

Remote management
Remote management allows you to remotely configure your Unicom Wireless Router over an
Internet connection. Since this is a potential security risk, this feature is turned off by default.
Unicom’s Wireless Router can be managed from any PC on your LAN. And, if the Internet
connection exists, it can also (optionally) be configured via the Internet.

29
 Enable web Server Access via WAN Check to enable the function.
Port number Enter the port number.
Save Click to save the current settings.
Reset Click to clear the current settings.

Config File
This feature allows you to download the current settings from the Wireless Router and save
them to a file on your PC.
You can restore a previously downloaded configuration file to the Wireless Router by
uploading it to the Wireless Router.
This screen also allows you to set the Wireless Router back to its factory default configuration.
Any existing settings will be deleted.
An example Config File screen is shown below.

Backup Config Use this to download a copy of the current configuration and
store the file on your PC. Click Download to start the
download.

Restore Config This allows you to restore a previously saved configuration

file back to the Wireless Router.
Click Browse to select the configuration file, then click
Restore to upload the configuration file.
WARNING !
Uploading a configuration file will destroy (overwrite) ALL of
the existing settings.

Default Config Clicking the Restore Defaults button will reset the Wireless
Router to its factory default settings.

WARNING !
This will delete ALL of the existing settings.

30
Log
The Logs record various types of activity on the Wireless Router. This data is useful for
troubleshooting, but enabling all logs will generate a large amount of data and adversely affect
performance.

Enable Log Check to enable logging function.

System All Activates all logging functions.

Wireless Only Only logs related to the wireless LAN will be recorded.

DoS Only Only logs related to the DoS protection will be recorded.

Save After completing the settings on this page, click Save to save them.

Refresh Click to refresh the logs.

Clear Click to delete the logs.

IP Filtering
Entries in this table are used to restrict certain types of data packets from your local network
entering the Internet through the Router. Here you can restrict local LAN clients to access
Internet application/services by IP Address. Use of such filters can be helpful in securing or
restricting your local network.

31
Enable IP Filtering Check to enable the IP filtering function.

Local IP Address Enter the client IP address.

Protocol Select the protocol (TCP, UDP or Both) used to the remote system
or service.

Description You may key in a description for the local IP address

Current Filter Table Shows the current filter information.

Delete Selected Click Delete Selected to delete selected items.

Delete All Click Delete All to delete all the items.

Reset Click Reset to rest

Save After completing the settings on this page, click Save to save them.

Reset Click Reset to restore to default values.

MAC Filtering
This screen is used to restrict devices on your local network from being able to access the
Internet. You do this by entering the MAC address of any device you want to restrict.

Enable MAC Check to enable MAC filtering function.

Filtering

MAC Address Enter the client MAC address.

Description You may key in a description for the MAC address.

32
Current Filter Table Shows the current filter information.

Delete Selected Click Delete Selected to delete all selected items.

Delete All Click Delete All to delete all the items.

Reset Click Reset to reset

Save After completing the settings on this page, click Save to save them.

Reset Click Reset to restore to default values.

Statistics

Refresh Click to refresh the statistics table.

Time Zone Setting

Current Time Enter the current time of this wireless router.

Enable NTP client Check to enable NTP (Network Time Protocol Server) client
update update function.

Time Zone Select Select the time zone from the pull-down menu.

NTP server You may choose to select NTP server from the pull-down menu or
enter an IP address of a specific server.

Save After completing the settings on this page, click Save to save
them.

Reset Click Reset to restore to default values.

33
Refresh Click to refresh the current time.

Upgrade Firmware

Browse Click the Browse button to find and open the firmware file. The
browser will display to correct file path.

Start Upgrade Click the Start Upgrade button to perform

Reset Click Reset to restore to default values.

Navigation & Data Input

• Use the menu bar on the left of the screen and the "Back" button on your Browser for
navigation.
• Changing to another screen without clicking "Save" does NOT save any changes you may
have made. You must "Save" before changing screens or your data will be ignored.

34
Chapter 4: PC Configuration
Overview
For each PC, the following may need to be configured:
• TCP/IP network settings
• Internet Access configuration
• Wireless configuration

Windows Clients
This section describes how to configure Windows clients for Internet access via the Wireless
Router.

The first step is to check the PC's TCP/IP settings.

The Wireless Router uses the TCP/IP network protocol for all functions, so it is essential that
the TCP/IP protocol be installed and configured on each PC.

TCP/IP Settings - Overview

If using the default Wireless Router settings, and the default

Windows TCP/IP settings, no changes need to be made.

• By default, the Wireless Router will act as a DHCP Server, automatically providing a
suitable IP Address (and related information) to each PC when the PC boots.
• For all non-Server versions of Windows, the default TCP/IP setting is to act as a DHCP
client.

If using a Fixed (specified) IP address, the following changes are

required:
• The Gateway must be set to the IP address of the Wireless Router
• The DNS should be set to the address provided by your ISP.

35
Checking TCP/IP Settings - Windows 98/ME:
1. Select Control Panel - Network. You should see a screen like the following:

2. Select the TCP/IP protocol for your network card.

3. Click on the Properties button. You should then see a screen like the following.

Ensure your TCP/IP settings are correct, as follows:

Using DHCP
To use DHCP, select the radio button Obtain an IP Address automatically. This is the default
Windows setting. Using this is recommended. By default, the Wireless Router will act as a
DHCP Server.
Restart your PC to ensure it obtains an IP Address from the Wireless Router.

Using "Specify an IP Address"

If your PC is already configured, check with your network administrator before making the
following changes:
• On the Gateway tab, enter the Wireless Router's IP address in the New Gateway field and
click Add, as shown below. Your LAN administrator can advise you of the IP Address
they assigned to the Wireless Router.

36
• On the DNS Configuration tab, ensure Enable DNS is selected. If the DNS Server Search
Order list is empty, enter the DNS address provided by your ISP in the fields beside the
Add button, then click Add.

37
Checking TCP/IP Settings - Windows NT4.0
1. Select Control Panel - Network and on the Protocols tab, select the TCP/IP protocol as
shown below.

38
2. Click the Properties button to see a screen like the one below.

3. Select the network card for your LAN.

4. Select the appropriate radio button - Obtain an IP address from a DHCP Server or Specify
an IP Address, as explained below.

Obtain an IP address from a DHCP Server

This is the default Windows setting. Using this is recommended. By default, the Wireless
Router will act as a DHCP Server.
Restart your PC to ensure it obtains an IP Address from the Wireless Router.

39
Specify an IP Address
If your PC is already configured, check with your network administrator before making the
following changes.
1. The Default Gateway must be set to the IP address of the Wireless Router. To set this:
• Click the Advanced button on the screen above.
• On the following screen, click the Add button in the Gateways panel, and enter the
Wireless Router's IP address.
• If necessary, use the Up button to make the Wireless Router the first entry in the
Gateways list.

40
2. The DNS should be set to the address provided by your ISP, as follows:
• Click the DNS tab.
• On the DNS screen, shown below, click the Add button (under DNS Service Search
Order), and enter the DNS provided by your ISP.

41
Checking TCP/IP Settings - Windows 2000:
1. Select Control Panel - Network and Dial-up Connection.
2. Right-click the Local Area Connection icon and select Properties. You should see a
screen like the following:

42
3. Select the TCP/IP protocol for your network card.
4. Click on the Properties button. You should then see a screen like the following.

5. Ensure your TCP/IP settings are correct, as described below.

Using DHCP
To use DHCP, select the radio button Obtain an IP Address automatically. This is the default
Windows setting. Using this is recommended. By default, the Wireless Router will act as a
DHCP Server.
Restart your PC to ensure it obtains an IP Address from the Wireless Router.

Using a fixed IP Address ("Use the following IP Address")

If your PC is already configured, check with your network administrator before making the
following changes.
• Enter the Wireless Router's IP address in the Default gateway field and click OK. (Your
LAN administrator can advise you of the IP Address they assigned to the Wireless
Router.)
• If the DNS Server fields are empty, select Use the following DNS server addresses, and
enter the DNS address or addresses provided by your ISP, then click OK.

43
Checking TCP/IP Settings - Windows XP
1. Select Control Panel - Network Connection.
2. Right click the Local Area Connection and choose Properties. You should see a screen
like the following:

3. Select the TCP/IP protocol for your network card.

44
4. Click on the Properties button. You should then see a screen like the following.

5. Ensure your TCP/IP settings are correct.

Using DHCP
To use DHCP, select the radio button Obtain an IP Address automatically. This is the default
Windows setting. Using this is recommended. By default, the Wireless Router will act as a
DHCP Server.
Restart your PC to ensure it obtains an IP Address from the Wireless Router.

Using a fixed IP Address ("Use the following IP Address")

If your PC is already configured, check with your network administrator before making the
following changes.
• In the Default gateway field, enter the Wireless Router's IP address and click OK. Your
LAN administrator can advise you of the IP Address they assigned to the Wireless Router.
• If the DNS Server fields are empty, select Use the following DNS server addresses, and
enter the DNS address or addresses provided by your ISP, then click OK.

45
Internet Access
To configure your PCs to use the Wireless Router for Internet access:
• Ensure that the DSL modem, Cable modem, or other permanent connection is functional.
• Use the following procedure to configure your Browser to access the Internet via the LAN,
rather than by a Dial-up connection.

For Windows 9x/ME/2000

1. Select Start Menu - Settings - Control Panel - Internet Options.
2. Select the Connection tab, and click the Setup button.
3. Select "I want to set up my Internet connection manually” or “I want to connect through a
local area network (LAN)" and click Next.
4. Select "I connect through a local area network (LAN)" and click Next.
5. Ensure all of the boxes on the following Local area network Internet Configuration screen
are unchecked.
6. Check the "No" option when prompted "Do you want to set up an Internet mail account
now?".
7. Click Finish to close the Internet Connection Wizard.
Setup is now completed.

For Windows XP
1. Select Start Menu - Control Panel - Network and Internet Connections.
2. Select Set up or change your Internet Connection.
3. Select the Connection tab, and click the Setup button.
4. Cancel the pop-up "Location Information" screen.
5. Click Next on the "New Connection Wizard" screen.
6. Select "Connect to the Internet" and click Next.
7. Select "Set up my connection manually" and click Next.
8. Check "Connect using a broadband connection that is always on" and click Next.
9. Click Finish to close the New Connection Wizard.
Setup is now completed.

Accessing AOL
To access AOL (America On Line) through the Wireless Router, the AOL for Windows
software must be configured to use TCP/IP network access rather than a dial-up connection.
The configuration process is as follows:
• Start the AOL for Windows communication software. Ensure that it is Version 2.5, 3.0 or
later. This procedure will not work with earlier versions.
• Click the Setup button.
• Select Create Location, and change the location name from "New Locality" to "Wireless
Router".
• Click Edit Location. Select TCP/IP for the Network field. (Leave the Phone Number
blank.)
• Click Save, then OK.
Configuration is now complete.
• Before clicking "Sign On", always ensure that you are using the "Wireless Router"
location.

46
Macintosh Clients
From your Macintosh, you can access the Internet via the Wireless Router. The procedure is as
follows.
1. Open the TCP/IP Control Panel.
2. Select Ethernet from the Connect via pop-up menu.
3. Select Using DHCP Server from the Configure pop-up menu. The DHCP Client ID field
can be left blank.
4. Close the TCP/IP panel, saving your settings.

Note:
If using manually assigned IP addresses instead of DHCP, the required changes are:
• Set the Router Address field to the Wireless Router's IP Address.
• Ensure your DNS settings are correct.

Linux Clients
To access the Internet via the Wireless Router, it is only necessary to set the Wireless Router
as the "Gateway".
Ensure you are logged in as "root" before attempting any changes.

Fixed IP Address
By default, most Unix installations use a fixed IP Address. If you wish to continue using a
fixed IP Address, make the following changes to your configuration.
• Set your "Default Gateway" to the IP Address of the Wireless Router.
• Ensure your DNS (Name server) settings are correct.

To act as a DHCP Client (recommended)

The procedure below may vary according to your version of Linux and X -windows shell.
1. Start your X Windows client.
2. Select Control Panel - Network
3. Select the "Interface" entry for your Network card. Normally, this will be called "eth0".
4. Click the Edit button, set the "protocol" to "DHCP", and save this data.
5. To apply your changes
• Use the "Deactivate" and "Activate" buttons, if available.
• OR, restart your system.

Other Unix Systems

To access the Internet via the Wireless Router:
• Ensure the "Gateway" field for your network card is set to the IP Address of the Wireless
Router.
• Ensure your DNS (Name Server) settings are correct.

47
Wireless Station Configuration
This section applies to all Wireless stations wishing to use the Wireless Router's Access Point,
regardless of the operating system that is used on the client.
To use the Wireless Access Point in the Wireless Router, each Wireless Station must have
compatible settings, as follows:

Mode The mode must be set to Infrastructure.

SSID (ESSID) This must match the value used on the Wireless Router. The default
value is Untitled
Note! The SSID is case sensitive.
WEP By default, WEP on the Wireless Router is disabled.
• If WEP remains disabled on the Wireless Router, all stations must
have WEP disabled.
• If WEP is enabled on the Wireless Router, each station must use the
same settings as the Wireless Router.

Note:
By default, the Wireless Router will allow both 802.11b and 802.11g connections.

48
Appendix A
Troubleshooting
Overview
This chapter covers some common problems that may be encountered while using the Unicom
802.11g Wireless Router and their possible solutions. If you follow the suggested steps and
the Wireless Router still does not function properly, contact your dealer for further advice.

General Problems
Problem 1: Can't connect to the Wireless Router to configure it.
Solution 1: Check the following:
• The Wireless Router is properly installed, LAN connections are OK,
and it is powered ON.
• Ensure that your PC and the Wireless Router are on the same network
segment. (If you don't have a router, this must be the case.)
• If your PC is set to "Obtain an IP Address automatically" (DHCP
client), restart it.
• If your PC uses a Fixed (Static) IP address, ensure that it is using an IP
Address within the range 192.168.1.1 to 192.168.1.253 and thus
compatible with the Wireless Router's default IP Address of
192.168.1.254.
Also, the Network Mask should be set to 255.255.255.0 to match the
Wireless Router.
In Windows, you can check these settings by using Control Panel-
Network to check the Properties for the TCP/IP protocol.

Internet Access
Problem 1: When I enter an URL or IP address I get a time out error.
Solution 1: A number of things could be causing this. Try the following
troubleshooting steps.
• Ensure other PCs work. If they do, ensure that your PCs IP settings are
correct. If using a Fixed (Static) IP Address, check the Network Mask,
Default gateway and DNS as well as the IP Address.
• If the PCs are configured correctly, but still not working, check the
Wireless Router. Ensure that it is connected and ON. Connect to it and
check its settings. (If you can't connect to it, check the LAN and power
connections.)
• If the Wireless Router is configured correctly, check your Internet
connection (DSL/Cable modem etc) to see that it is working correctly.
 Problem 2: Some applications do not run properly when using the Wireless
Router.

Solution 2: The Wireless Router processes the data passing through it, so it is not
transparent. Use the Special Applications feature to allow the use of Internet
applications that do not function correctly.
If this does solve the problem you can use the DMZ function.
This should work with almost every application, however:
1. It is a security risk, since the firewall is disabled.
2. Only one (1) PC can use this feature.

Wireless Access
Problem 1: My PC can't locate the Wireless Access Point.
Solution 1: Check the following.
• Your PC is set to Infrastructure Mode. (Access Points are always in
Infrastructure Mode)
• Ensure the SSID on your PC and the Wireless Access Point are the
same. Remember that the SSID is case-sensitive. So, for example
"Workgroup" does NOT match "workgroup".
• Both your PC and the Wireless Router must have the same setting for
WEP. The default setting for the Wireless Router is disabled, so your
wireless station should also have WEP disabled.
• If WEP is enabled on the Wireless Router, your PC must have WEP
enabled and the key must match.
• If the Wireless Router's Wireless screen is set to Allow LAN access to
selected Wireless Stations only, then each of your Wireless stations
must have been selected or access will be blocked.
• To check if radio interference is causing a problem, see if connection is
possible when near the Wireless Router. Remember that the connection
range can be as little as 100 feet in poor environments.
Problem 2: Wireless connection speed is very slow.
Solution 2: The wireless system will connect at the highest possible speed, depending
on the distance and the environment. To obtain the highest possible
connection speed, you can experiment with the following:
• Wireless Router location.
Try adjusting the location and orientation of the Wireless Router.
• Wireless Channel
If interference is the problem, changing to another channel may show a
marked improvement.
• Radio Interference
Other devices may be causing interference. You can experiment by
switching other devices off and see if this helps. Any "noisy" devices
should be shielded or relocated.
• RF Shielding
Your environment may tend to block transmission between the wireless
stations. This will mean high access speed is only possible when close
to the Wireless Router.

50
Appendix B
About Wireless LANs
Modes
B
Wireless LANs can work in either of two (2) modes:
• Ad-hoc
• Infrastructure

Ad-hoc Mode
Ad-hoc mode does not require an Access Point or a wired (Ethernet) LAN. Wireless
Stations (e.g. notebook PCs with wireless cards) communicate directly with each other.

Infrastructure Mode
In Infrastructure Mode, one or more Access Points are used to connect Wireless Stations
(e.g. Notebook PCs with wireless cards) to a wired (Ethernet) LAN. The Wireless Stations
can then access all LAN resources.

Access Points can only function in "Infrastructure" mode,

and can communicate only with Wireless Stations that are
set to "Infrastructure" mode.

BSS

BSS
A group of Wireless Stations and a single Access Point, all using the same ID (SSID), form a
Basic Service Set (BSS).
Using the same SSID is essential. Devices with different SSIDs are unable to communicate
with each other.

Channels
The Wireless Channel sets the radio frequency used for communication.
• Access Points use a fixed Channel. You can select the Channel used. This allows you to
choose a Channel which provides the least interference and best performance. In the USA
and Canada, 11 channels are available. If using multiple Access Points, it is better if
adjacent Access Points use different Channels to reduce interference.
• In "Infrastructure" mode, Wireless Stations normally scan all Channels, looking for an
Access Point. If more than one Access Point can be used, the one with the strongest signal
is used. (This can only happen within an ESS.)
WEP
WEP (Wired Equivalent Privacy) is a standard for encrypting data before it is transmitted.
This is desirable because it is impossible to prevent snoopers from receiving any data that is
transmitted by your Wireless Stations. But if the data is encrypted, then it is meaningless
unless the receiver can decrypt it.
If WEP is used, the Wireless Stations and the Access Point must have the same settings
for each of the following:

WEP Off, 64 Bit, 128 Bit

Key For 64 Bit encryption, the Key value must match.
For 128 Bit encryption, the Key value must match
WEP Authentication Open System or Shared Key.

Wireless LAN Configuration

To allow Wireless Stations to use the Access Point, the Wireless Stations and the Access
Point must use the same settings, as follows:

Mode On client Wireless Stations, the mode must be set to "Infrastructure".

(The Access Point is always in "Infrastructure" mode.)
SSID (ESSID) Wireless Stations should use the same SSID (ESSID) as the Access
Point they wish to connect to. Alternatively, the SSID can be set to
"any" or null (blank) to allow connection to any Access Point.
WEP The Wireless Stations and the Access Point must use the same settings
for WEP (Off, 64 Bit, 128 Bit).
WEP Key: If WEP is enabled, the Key must be the same on the
Wireless Stations and the Access Point.
WEP Authentication: If WEP is enabled, all Wireless Stations must
use the same setting as the Access Point (either "Open System" or
"Shared Key").

52
Appendix C
Specifications C
Multi-Function Wireless Router
Model 802.11g Wireless Router

Dimensions 141mm(W) x 100mm(D) x 27mm(H)

Operating Temperature 0° C to 40° C

Storage Temperature -10° C to 70° C

Network Protocol: TCP/IP

Network Interface: 5 Ethernet:

4 x 10/100Base-T (RJ45) LAN connection
1 x 10/100Base-T (RJ45) for WAN

LEDs 12

Power Adapter 12 V DC External

Wireless Interface
Standards IEEE802.11g WLAN, JEIDA 4.2, roaming support

Frequency 2.4 to 2.4835GHz (Industrial Scientific Medical Band )

Channels Maximum 14 Channels, depending on regulatory authorities

Modulation DSSS BPSK/QPSK/CCK, OFDM/CCK

Data Rate Up to 54 Mbps

Coverage Area Indoors : 15m @54Mbps, 120m @6Mbps or lower

Outdoors : 40m @54Mbps, 300m @6Mbps or lower

WEP 64Bit, 128Bit

Output Power 13dBm (typical)

Receiver Sensitivity -80dBm Min.

Regulatory Approvals

CE Standards
This product complies with the 99/5/EEC directives, including the following safety and EMC
standards:
• EN300328-2
• EN301489-1/-17
• EN60950

CE Marking Warning
This is a Class B product. In a domestic environment this product may cause radio interference
in which case the user may be required to take adequate measures.

54