TONEI ON BP Synthetic Enamel qd To 18:2932 So { Scope ” Uses BP Synthetic Enamel is formulated to give . | aglossy durable coating meeting IS: 2932 Recommended for use on tank ext | | spe tion. It is ideally suitable for structurals, pipelines, cladding gantries ete, application on primed stee! structures in polluted atmosphere. f Resistance Guide ——————— Chemical Resist ‘Composition: Modified alkyd medium Chemical Resistance Suitably pigmented Exposures Splash Mild Fumes / ‘Application: Brush conventional or airless and spillage outdoor spray Resistai Recommended DFT: 20-25 microns Aes na far Corresponding WFT: 85-125 microns per ‘alkalis NR Fair coat Solvent NIR Fair Theoretical Spreading Rate: 12.0-15.0 Sq Salt Good Good Mir/ Lar * Water Good Good Drying time: * Not recommended for Immersion TOUCH: 3-4 hours . HANDLE: 8 hours Temperature Resistance: HARD: — Overnight - Continuous: 80 degree C Overcoating Interval: Min: Overnight Intermittent: 100 degree C Flash Point: Above 30 degree C Weatherability: Good under mild industrial Colour: Assorted shade and chemical exposure Packing: 20 Lir Thinner / Cleaner: Thinner 800 Flexibility: Excellent Finish: —G ° Abrasion Resistance: Moderate Storage Life: Up to twelve months as long as the sealed containers are kept under cover in Data Sheet No. 008/1 a dry place under normal temperature condiSurface Preparation STEEL: Remove grease, oil and other contaminants preferably by using Bison Degreasing Solvent, Blast clean to a ‘minimum Sa 2 1/2 Swedish Standards SIS 05 5900 with a surface profile not exceeding 65 microns, If blasting is not practical, make full use of mechanical tools alongwith manual chipping and wire brushing to remove loose rust and scale to St.2 Swedish Standard SIS 05 5900. Excessive burnishing of steel is to be avoided. Thoroughly dust down all surfaces. Best results can be achieved if the manually cleaned surface is treated with Bison Metal Conditioning Solution. ‘The surface should be clean and dry before application of appropriate primer coat Application Mix the contents thoroughly before and during use. Brush: Apply without any thinning, Airless spray: Add upto 5% Thinner 800 if required, Use any standard equipment having pump ratio 30:1. Tip size 0.28.0.38 mm. tip pressure 110-160 kg / m2, ‘Typical Painting Specifications Surface Ist coat Ist coat 2nd coat 3rd coat 4" Coat Steel ROZC or Bison Syn RIL ROZC or Bison Syn R/L_BP Synthetic BP Synthetic Or Bison HB Z/P Primer or Bison HB Z/P Primer Enamel Enamel Or Luxol Z/C Primer or Luxol Z/C Primer -do- -do- Bison HB MIO. -do- -do- Concrete Luxol Clear Varnish or BP Synthetic -do- Thinned coat of BP Enamel Synthetic Enamel Galvanished iron Degrease and abrade the surface. Apply Bison Wash Primer followed by any of Aluminium, the above systems excluding the primer coats. Berger Paints India Ltd BERGERHOUSE 129 Park Street Calcutta — 700 017 Tel: (033) 22499724 (5 lines) 22499754 (4 lines) Fax: 91-33-22499729/9009 Notes: 1. Allow minimum 48 hours before subjecting the painted surface to service conditions. 2. Do not apply when temperature falls below 10 degree C or rises above $0 degree C when relative humidity rises above 90%, Do not apply during rain, fog or mis Health & Safety - Please refer to the separate safety data sheet Data Sheet No. 008/1 Disclaimer ‘The information contained herein within this data sheet is based on information believed to be reliable atthe time of its preparation. The Company will not be liable for loss or damage howsoever caused including liability for negligence, which may be suffered by the user of the data contained herein. It is the users’ responsibility to conduct all necessary tests to confirm the suitability of any product or system for their intended use. No ‘guarantee of results is implied since conditions of use are beyond our control. Issue Date: Oct. 2005