Scribd
Upload
55 views

Connection 2

This document contains design details for Project Item 15, including: - Project name, number, author, date, and design code - Materials, cross sections, and load effects for beams and columns - Checks for analysis, plates, bolts, welds, and buckling - Details of equivalent stresses, strains, and bolt capacities

Uploaded by

Der3'am Al m7armeh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
55 views

Connection 2

This document contains design details for Project Item 15, including: - Project name, number, author, date, and design code - Materials, cross sections, and load effects for beams and columns - Checks for analysis, plates, bolts, welds, and buckling - Details of equivalent stresses, strains, and bolt capacities

Uploaded by

Der3'am Al m7armeh
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 19

Project:

Project no:
Author:

Project data
Project name
Project number
Author
Description
Date 4/3/2022
Design code AISC 360-16

Material
Steel A36

1 / 19
Project:
Project no:
Author:

Project item 15

Design
Name 15
Description
Analysis Stress, strain/ loads in equilibrium
Design code AISC - ASD 2016

Beams and columns


β – Direction γ - Pitch α - Rotation Offset ex Offset ey Offset ez
Name Cross-section Forces in
[°] [°] [°] [mm] [mm] [mm]
19 2 - IPE200 0.0 0.0 0.0 0 0 0 Position
8 3 - HEB200 0.0 0.0 0.0 0 0 0 Position
18 4 - IPE300 0.0 0.0 0.0 0 0 0 Position
52 2 - IPE200 0.0 0.0 0.0 0 0 0 Position
113 2 - IPE200 0.0 0.0 0.0 0 0 0 Position

2 / 19
Project:
Project no:
Author:

3 / 19
Project:
Project no:
Author:

Cross-sections
Name Material
2 - IPE200 A36
3 - HEB200 A36
4 - IPE300 A36

4 / 19
Project:
Project no:
Author:

Cross-sections
Name Material Drawing

2 - IPE200 A36

3 - HEB200 A36

4 - IPE300 A36

Bolts
Diameter fu Gross area
Name Bolt assembly
[mm] [MPa] [mm2]
16 A325M 16 A325M 16 830.0 201
20 A325M 20 A325M 20 830.0 314

5 / 19
Project:
Project no:
Author:

Load effects (forces in equilibrium)


N Vy Vz Mx My Mz
Name Member
[kN] [kN] [kN] [kNm] [kNm] [kNm]
DSTL2(2) 19 0.8 -0.1 -26.7 0.0 25.3 0.0
8 90.1 -1.1 12.9 0.0 34.9 3.0
18 9.8 0.1 -54.0 0.0 -60.2 -0.2
52 1.0 0.0 3.6 0.0 -1.0 0.0
113 0.0 2.3 -12.9 0.0 1.9 0.2

Check

Summary
Name Value Check status
Analysis 100.0% OK
Plates 0.4 < 5.0% OK
Bolts 81.8 < 100% OK
Welds 85.0 < 100% OK
Buckling Not calculated

6 / 19
Project:
Project no:
Author:

Plates
fy Thickness σEd εPl σcEd
Name Loads Check status
[MPa] [mm] [MPa] [%] [MPa]
19-bfl 1 248.2 8.5 DSTL2(2) 145.4 0.0 0.0 OK
19-tfl 1 248.2 8.5 DSTL2(2) 148.7 0.0 0.0 OK
19-w 1 248.2 5.6 DSTL2(2) 148.7 0.1 3.9 OK
8-bfl 1 248.2 15.0 DSTL2(2) 73.8 0.0 0.0 OK
8-tfl 1 248.2 15.0 DSTL2(2) 148.7 0.0 0.0 OK
8-w 1 248.2 9.0 DSTL2(2) 148.9 0.1 0.0 OK
18-bfl 1 248.2 10.7 DSTL2(2) 148.7 0.0 0.0 OK
18-tfl 1 248.2 10.7 DSTL2(2) 148.7 0.0 0.0 OK
18-w 1 248.2 7.1 DSTL2(2) 127.3 0.0 0.0 OK
52-bfl 1 248.2 8.5 DSTL2(2) 46.4 0.0 0.0 OK
52-tfl 1 248.2 8.5 DSTL2(2) 37.1 0.0 0.0 OK
52-w 1 248.2 5.6 DSTL2(2) 32.0 0.0 0.5 OK
113-bfl 1 248.2 8.5 DSTL2(2) 53.6 0.0 0.0 OK
113-tfl 1 248.2 8.5 DSTL2(2) 58.4 0.0 0.0 OK
113-w 1 248.2 5.6 DSTL2(2) 45.7 0.0 0.6 OK
FP1 248.2 14.0 DSTL2(2) 33.4 0.0 3.9 OK
FP2 248.2 14.0 DSTL2(2) 7.8 0.0 2.2 OK
FP2 248.2 12.0 DSTL2(2) 14.6 0.0 0.6 OK
STUB1 1 248.2 10.7 DSTL2(2) 148.6 0.0 0.0 OK
STUB1 2 248.2 10.7 DSTL2(2) 148.9 0.1 0.0 OK
STUB1 3 248.2 7.1 DSTL2(2) 149.0 0.2 0.0 OK
STUB1-EPa 248.2 16.0 DSTL2(2) 149.2 0.3 61.3 OK
STUB1-EPb 248.2 16.0 DSTL2(2) 149.5 0.4 61.3 OK
STIFF2a 248.2 12.0 DSTL2(2) 70.2 0.0 0.0 OK
STIFF2b 248.2 12.0 DSTL2(2) 73.7 0.0 0.0 OK

Design data
fy εlim
Material
[MPa] [%]
A36 248.2 5.0

Symbol explanation
εPl Plastic strain
σcEd Contact stress
σEd Eq. stress
fy Yield strength
εlim Limit of plastic strain

7 / 19
Project:
Project no:
Author:

Overall check, DSTL2(2)

Strain check, DSTL2(2)

8 / 19
Project:
Project no:
Author:

Equivalent stress, DSTL2(2)

9 / 19
Project:
Project no:
Author:

Bolts
Ft V Rn/ΩBearing Utt Uts Utts
Shape Item Grade Loads Status
[kN] [kN] [kN] [%] [%] [%]
B1 16 A325M - 1 DSTL2(2) 1.2 2.2 43.0 2.0 5.9 - OK

B2 16 A325M - 1 DSTL2(2) 1.6 0.9 34.9 2.6 2.5 - OK

B3 16 A325M - 1 DSTL2(2) 0.5 2.3 43.0 0.8 6.1 - OK

B4 16 A325M - 1 DSTL2(2) 0.2 0.9 43.0 0.3 2.4 - OK

B5 16 A325M - 1 DSTL2(2) 0.1 0.3 43.0 0.2 0.8 - OK

B6 16 A325M - 1 DSTL2(2) 0.2 0.2 43.0 0.3 0.6 - OK

B7 16 A325M - 1 DSTL2(2) 0.1 0.3 43.0 0.2 0.8 - OK

B8 16 A325M - 1 DSTL2(2) 0.1 0.2 43.0 0.2 0.7 - OK

B9 16 A325M - 1 DSTL2(2) 0.2 0.6 43.0 0.4 1.6 - OK

B10 16 A325M - 1 DSTL2(2) 0.2 0.2 43.0 0.3 0.7 - OK

B11 16 A325M - 1 DSTL2(2) 0.2 0.6 43.0 0.3 1.7 - OK

B12 16 A325M - 1 DSTL2(2) 0.3 0.3 43.0 0.5 0.8 - OK

B13 20 A325M - 2 DSTL2(2) 79.6 5.9 145.9 81.7 10.1 - OK


B14 20 A325M - 2 DSTL2(2) 79.6 5.8 145.9 81.8 9.9 - OK
B15 20 A325M - 2 DSTL2(2) 42.0 6.8 145.9 43.2 11.6 - OK
B16 20 A325M - 2 DSTL2(2) 42.0 6.7 145.9 43.1 11.4 - OK
B17 20 A325M - 2 DSTL2(2) 28.5 7.1 145.9 29.3 12.1 - OK
B18 20 A325M - 2 DSTL2(2) 28.5 7.0 145.9 29.3 12.0 - OK
B19 20 A325M - 2 DSTL2(2) 6.3 7.4 145.9 6.5 12.7 - OK
B20 20 A325M - 2 DSTL2(2) 6.3 7.4 145.9 6.4 12.6 - OK

Design data
Rn/ΩTension Rn/ΩShear
Grade
[kN] [kN]
16 A325M - 1 62.3 37.4
20 A325M - 2 97.3 58.4

Symbol explanation
Ft Tension force
V Resultant of shear forces Vy, Vz in bolt
Rn/ΩBearing Bolt bearing resistance
Utt Utilization in tension
Uts Utilization in shear
Utts Utilization in tension and shear
Rn/ΩTension Bolt tension resistance AISC 360-16 J3.6
Rn/ΩShear Bolt shear resistance AISC 360-16 – J3.8

10 / 19
Project:
Project no:
Author:

Weld sections
Th Ls L Lc Fn Rn/Ω Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
8-bfl 1 FP1 E70xx ◢4.0◣ ◢5.7◣ 179 11 DSTL2(2) 2.0 6.9 28.9 OK
E70xx ◢4.0◣ ◢5.7◣ 179 11 DSTL2(2) 1.9 9.0 20.9 OK
8-tfl 1 19-tfl 1 E70xx ◢4.3◣ ◢6.0◣ 100 25 DSTL2(2) 17.4 22.9 75.7 OK
E70xx ◢4.3◣ ◢6.0◣ 100 25 DSTL2(2) 17.3 22.8 75.8 OK
8-tfl 1 19-bfl 1 E70xx ◢4.3◣ ◢6.0◣ 100 25 DSTL2(2) 17.3 23.0 75.2 OK
E70xx ◢4.3◣ ◢6.0◣ 100 25 DSTL2(2) 17.4 22.8 76.2 OK
8-w 1 52-bfl 1 E70xx ◢4.0◣ ◢5.7◣ 100 25 DSTL2(2) 5.0 14.7 34.3 OK
E70xx ◢4.0◣ ◢5.7◣ 100 25 DSTL2(2) 4.8 16.0 30.0 OK
8-w 1 52-tfl 1 E70xx ◢4.0◣ ◢5.7◣ 100 25 DSTL2(2) 3.8 16.4 23.3 OK
E70xx ◢4.0◣ ◢5.7◣ 100 25 DSTL2(2) 4.5 14.8 30.2 OK
8-w 1 52-w 1 E70xx ◢4.0◣ ◢5.7◣ 191 24 DSTL2(2) 2.0 20.7 9.7 OK
E70xx ◢4.0◣ ◢5.7◣ 191 24 DSTL2(2) 3.0 19.5 15.4 OK
8-w 1 FP2 E70xx ◢4.0◣ ◢5.7◣ 178 11 DSTL2(2) 0.7 7.8 8.6 OK
E70xx ◢4.0◣ ◢5.7◣ 179 11 DSTL2(2) 0.7 9.0 7.9 OK
8-w 1 113-bfl 1 E70xx ◢4.0◣ ◢5.7◣ 100 25 DSTL2(2) 5.4 15.6 34.7 OK
E70xx ◢4.0◣ ◢5.7◣ 100 25 DSTL2(2) 6.8 15.8 42.9 OK
8-w 1 113-tfl 1 E70xx ◢4.0◣ ◢5.7◣ 100 25 DSTL2(2) 8.2 16.0 51.4 OK
E70xx ◢4.0◣ ◢5.7◣ 100 25 DSTL2(2) 6.9 15.5 44.3 OK
8-w 1 113-w 1 E70xx ◢4.0◣ ◢5.7◣ 191 24 DSTL2(2) 1.9 20.0 9.7 OK
E70xx ◢4.0◣ ◢5.7◣ 191 24 DSTL2(2) 2.0 20.3 9.8 OK
8-w 1 FP2 E70xx ◢4.0◣ ◢5.7◣ 179 11 DSTL2(2) 1.2 8.4 14.7 OK
E70xx ◢4.0◣ ◢5.7◣ 179 11 DSTL2(2) 1.4 8.2 17.5 OK
STUB1-EPb STUB1 3 E70xx ◢3.0◣ ◢4.2◣ 277 20 DSTL2(2) 10.8 12.9 83.8 OK
E70xx ◢3.0◣ ◢4.2◣ 277 20 DSTL2(2) 10.8 12.9 83.8 OK
STUB1 1 STUB1 3 E70xx ◢5.0◣ ◢7.1◣ 184 23 DSTL2(2) 12.1 24.4 49.7 OK
E70xx ◢5.0◣ ◢7.1◣ 184 23 DSTL2(2) 12.2 24.4 50.2 OK
STUB1-EPa 18-bfl 1 E70xx ◢5.0◣ ◢7.1◣ 149 19 DSTL2(2) 14.5 20.3 71.8 OK
E70xx ◢5.0◣ ◢7.1◣ 149 19 DSTL2(2) 15.2 20.3 75.1 OK
STUB1-EPa 18-tfl 1 E70xx ◢5.0◣ ◢7.1◣ 149 19 DSTL2(2) 14.7 19.5 75.2 OK
E70xx ◢5.0◣ ◢7.1◣ 149 19 DSTL2(2) 13.9 18.5 75.0 OK
STUB1-EPa 18-w 1 E70xx ◢3.0◣ ◢4.2◣ 288 21 DSTL2(2) 11.3 13.4 85.0 OK
E70xx ◢3.0◣ ◢4.2◣ 288 21 DSTL2(2) 11.4 13.4 85.0 OK
STUB1-EPb STUB1 1 E70xx ◢5.0◣ ◢7.1◣ 149 19 DSTL2(2) 14.3 20.3 70.8 OK
E70xx ◢5.0◣ ◢7.1◣ 149 19 DSTL2(2) 15.2 20.2 75.1 OK
STUB1-EPb STUB1 2 E70xx ◢5.0◣ ◢7.1◣ 149 19 DSTL2(2) 12.0 19.9 60.2 OK
E70xx ◢5.0◣ ◢7.1◣ 150 19 DSTL2(2) 14.2 18.9 75.1 OK
STUB1 2 STUB1 3 E70xx ◢5.0◣ ◢7.1◣ 183 23 DSTL2(2) 11.9 19.8 60.1 OK
E70xx ◢5.0◣ ◢7.1◣ 183 23 DSTL2(2) 11.8 19.9 59.2 OK
8-tfl 1 STUB1 1 E70xx ◢4.0◣ ◢5.7◣ 149 21 DSTL2(2) 14.3 18.5 77.1 OK

11 / 19
Project:
Project no:
Author:

Th Ls L Lc Fn Rn/Ω Ut
Item Edge Xu Loads Status
[mm] [mm] [mm] [mm] [kN] [kN] [%]
E70xx ◢4.0◣ ◢5.7◣ 149 21 DSTL2(2) 14.5 18.5 78.4 OK
8-tfl 1 STUB1 3 E70xx ◢4.0◣ ◢5.7◣ 278 25 DSTL2(2) 16.5 21.9 75.4 OK
E70xx ◢4.0◣ ◢5.7◣ 278 25 DSTL2(2) 16.5 21.9 75.4 OK
8-tfl 1 STUB1 2 E70xx ◢4.0◣ ◢5.7◣ 149 21 DSTL2(2) 14.1 18.5 76.0 OK
E70xx ◢4.0◣ ◢5.7◣ 149 21 DSTL2(2) 14.1 18.5 76.2 OK
8-bfl 1 STIFF2a E70xx ◢4.0◣ ◢5.7◣ 77 19 DSTL2(2) 2.8 14.6 19.3 OK
E70xx ◢4.0◣ ◢5.7◣ 77 19 DSTL2(2) 2.6 13.1 20.2 OK
8-w 1 STIFF2a E70xx ◢4.0◣ ◢5.7◣ 134 22 DSTL2(2) 3.0 18.1 16.6 OK
E70xx ◢4.0◣ ◢5.7◣ 134 22 DSTL2(2) 3.4 15.8 21.4 OK
8-tfl 1 STIFF2a E70xx ◢4.0◣ ◢5.7◣ 77 19 DSTL2(2) 6.6 15.4 43.0 OK
E70xx ◢4.0◣ ◢5.7◣ 77 19 DSTL2(2) 2.6 15.5 16.7 OK
8-bfl 1 STIFF2b E70xx ◢4.0◣ ◢5.7◣ 77 19 DSTL2(2) 2.4 12.4 19.4 OK
E70xx ◢4.0◣ ◢5.7◣ 77 19 DSTL2(2) 3.5 15.6 22.3 OK
8-w 1 STIFF2b E70xx ◢4.0◣ ◢5.7◣ 134 22 DSTL2(2) 3.5 17.5 19.8 OK
E70xx ◢4.0◣ ◢5.7◣ 134 22 DSTL2(2) 3.3 19.3 17.1 OK
8-tfl 1 STIFF2b E70xx ◢4.0◣ ◢5.7◣ 77 19 DSTL2(2) 2.4 15.5 15.5 OK
E70xx ◢4.0◣ ◢5.7◣ 77 19 DSTL2(2) 6.9 15.8 43.6 OK

Symbol explanation
Th Throat thickness of weld
Ls Leg size of weld
L Length of weld
Lc Length of weld critical element
Fn Force in weld critical element
Rn/Ω Weld resistance AISC 360-16 J2.4
Ut Utilization

Buckling
Buckling analysis was not calculated.

12 / 19
Project:
Project no:
Author:

Bill of material

Manufacturing operations
Plates Welds Length
Name Shape Nr. Bolts Nr.
[mm]
[mm]
[mm]

FP1 P14.0x150.0-180.0 (A36) 1 Double fillet: a = 4.0 180.0 16 A325M 4





CUT4 Double fillet: a = 4.0 391.5



FP2 P14.0x150.0-180.0 (A36) 1 Double fillet: a = 4.0 180.0 16 A325M 4





CUT4 Double fillet: a = 4.0 391.5



FP2 P12.0x150.0-180.0 (A36) 1 Double fillet: a = 4.0 180.0 16 A325M 4





CUT1

Double fillet: a = 5.0 1636.0


STUB1 P16.0x150.0-320.0 (A36) 1 20 A325M 8
Double fillet: a = 3.0
846.5

P16.0x150.0-320.0 (A36) 1

STIFF2 P12.0x95.5-170.0 (A36) 2 Double fillet: a = 4.0 578.0



13 / 19
Project:
Project no:
Author:

Welds
Throat thickness Leg size Length
Type Material

[mm] [mm]
[mm]

Double fillet E70xx 4.0 5.7 2479.6


Double fillet E70xx 4.3 6.0 200.0
Double fillet E70xx 3.0 4.2 567.9
Double fillet E70xx 5.0 7.1 968.0

Bolts
Grip length
Name Count
[mm]
16 A325M 20 8
16 A325M 18 4
20 A325M 32 8

Drawing

FP1

P14.0x180-150 (A36)

14 / 19
Project:
Project no:
Author:

FP2

P14.0x180-150 (A36)

15 / 19
Project:
Project no:
Author:

FP2

P12.0x180-150 (A36)

STUB1 - STUB1-EPa

P16.0x320-150 (A36)

16 / 19
Project:
Project no:
Author:

STUB1 - STUB1-EPb

P16.0x320-150 (A36)

STIFF2

P12.0x170-96 (A36)

17 / 19
Project:
Project no:
Author:

19, IPE200 - Web 1:

52, IPE200 - Web 1:

18 / 19
Project:
Project no:
Author:

113, IPE200 - Web 1:

Code settings
Item Value Unit Reference
Friction coefficient - concrete 0.40 - ACI 349 – B.6.1.4
Friction coefficient in slip-resistance 0.30 - AISC 360-16 J3.8
Limit plastic strain 0.05 -
Plastic
Weld stress evaluation
redistribution
Detailing No
Distance between bolts [d] 2.66 - AISC 360-16 – J3.3
Distance between bolts and edge [d] 1.25 - AISC 360-16 – J.3.4
Concrete breakout resistance check Both
Base metal capacity check at weld fusion
No AISC 360-16: J2-2
face
Cracked concrete Yes ACI 318-14 – Chapter 17
Local deformation check No
Local deformation limit 0.03 - CIDECT DG 1, 3 - 1.1
Analysis with large deformations for hollow section
Geometrical nonlinearity (GMNA) Yes
joints

19 / 19

You might also like