Scribd
Upload
210 views5 pages

C6.6 Cam Shaft Install

This document provides instructions for removing and installing a camshaft on a C6.6 Industrial Engine. Key steps include: 1. Remove the rocker shaft, pushrods and front housing. 2. Remove the thrust washer from the cylinder block and carefully remove the camshaft. 3. Clean and inspect the camshaft, thrust washer and camshaft bearings, replacing any worn parts. Lubricate the camshaft and install into the cylinder block with the thrust washer. 4. Reinstall the front housing, rocker shaft and pushrods.

Uploaded by

sen
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
210 views5 pages

C6.6 Cam Shaft Install

This document provides instructions for removing and installing a camshaft on a C6.6 Industrial Engine. Key steps include: 1. Remove the rocker shaft, pushrods and front housing. 2. Remove the thrust washer from the cylinder block and carefully remove the camshaft. 3. Clean and inspect the camshaft, thrust washer and camshaft bearings, replacing any worn parts. Lubricate the camshaft and install into the cylinder block with the thrust washer. 4. Reinstall the front housing, rocker shaft and pushrods.

Uploaded by

sen
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 5

Shutdown SIS

Previous Screen
Welcome: j093ban
Product: INDUSTR IAL ENGINE
Mode l: C 6.6 INDUSTR IAL ENGINE 66621626
C onfiguration: C 6.6 Industrial Engine 66600001-UP

Disassembly and Assembly


C6.6 Industrial Engine
Media Number -RENR9722-01 Publication Date -01/10/2007 Date Updated -10/10/2007

i02786879

Camshaft - Remove and Install


SMCS - 1210-010

Removal Procedure
Start By:

A. Remove the rockershaft and pushrods. Refer to Disassembly and Assembly, "Rocker shaft and Pushrod -
Remove".
B. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Remove".

NOTICE
Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

1. The engine should be mounted on a suitable stand and placed in the inverted position.
Illustration 1 g01340531
Typical example

2. Remove thrust washer (1) from the cylinder block. Do not remove dowel (2) from the cylinder block
unless the dowel is damaged.

Note: The thrust washer can have one or two slots (X) .

Illustration 2 g01340532
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.

3. Carefully remove camshaft (3) from the cylinder block.

4. If necessary, remove key (4) from camshaft (3) .

Installation Procedure

NOTICE
Keep all parts clean from contaminants.

Contaminants may cause rapid wear and shortened component life.

1. Clean the camshaft and the thrust washer. Inspect the camshaft and the thrust washer for wear and for
damage. Refer to Specifications, "Camshaft" for more information. Replace any worn components or any
damaged components.

2. Clean the camshaft bearing in the cylinder block. Inspect the camshaft bearing for wear and for damage.
Refer to Specifications, "Camshaft Bearings" for more information. If necessary, replace the camshaft
bearing. Refer to Disassembly and Assembly, "Camshaft Bearing - Remove and Install".

NOTICE
It is strongly recommended that all lifters should be replaced when a new
camshaft is installed.

3. Inspect the lifters for wear and for damage. Refer to Specifications, "Lifter Group" for more information.
Replace any worn lifters or any damaged lifters. Refer to Disassembly and Assembly, "Lifter Group -
Remove and install".
Illustration 3 g01340531
Typical example

4. If necessary, install a new key (4) into camshaft (3) .

5. Lubricate the bearing surfaces of camshaft (3) and lubricate the lobes of the camshaft with clean engine oil.

NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.

6. Carefully install camshaft (3) into the cylinder block.


Illustration 4 g01167327
Typical example

7. Lubricate the thrust washer with clean engine oil. Align slot (X) in thrust washer (1) with dowel (2) in the
cylinder block. Install thrust washer (1) into the recess in the cylinder block.

Note: The thrust washer can have one or two slots (X) .

End By:

a. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
b. Install the rockershaft and pushrods. Refer to Disassembly and Assembly, "Rocker shaft and Pushrod -
Install".

C opyright 1993 - 2013 C ate rpillar Inc.


Fri Nov 22 2013 12:12:22 GMT+0530 (India Standard Tim e )
All R ights R e se rve d.
Private Ne twork For SIS Lice nse e s. j093ban

You might also like