HCD-BX9/DX9

SERVICE MANUAL AEP Model

UK Model
Ver 1.1 2001. 06 HCD-BX9

E Model
Australian Model
HCD-DX9

HCD-BX9/DX9 is the tuner, deck, CD and

amplifier section in MHC-BX9/DX9. Photo: HCD-DX9

Model Name Using Similar Mechanism HCD-BX7/DX7/DX7J

CD CD Mechanism Type CDM58-K2BD38
SECTION
Base Unit Type BU-K2BD38
Optical Pick-up Type KSM-213DAP/ZNP
TAPE DECK Model Name Using Similar Mechanism HCD-BX7/DX7/DX7J
SECTION Tape Transport Mechanism Type TCM-230MWR11

SPECIFICATIONS
Amplifier section CD player section Tuner section
European model: System FM stereo, FM/AM superheterodyne tuner
DIN power output (rated) Compact disc and digital audio system
130 + 130 W Laser FM tuner section
(6 Ω at 1 kHz, DIN) Semiconductor laser (λ=780 nm) Tuning range
Continuous RMS power output (reference) Emission duration: continuous 87.5 – 108.0 MHz
170 + 170 W Laser output Antenna
(6 Ω at 1 kHz, 10% THD) Max. 44.6 µW* FM lead antenna
*This output is the value measured at a Antenna terminals
Other models: distance of 200 mm from the objective 75 Ω, unbalanced
The following measured at AC 120, 220, 240 V lens surface on the Optical Pick-up Block Intermediate frequency
50/60 Hz with 7 mm aperture. 10.7 MHz
DIN power output (rated) Frequency response
220 + 220 W 2 Hz – 20 kHz (±0.5 dB)
Wavelength
AM tuner section
(4 Ω at 1 kHz, DIN) Tuning range
Continuous RMS power output (reference) 780 – 790 nm
BX9, Saudi Arabia models:
300 + 300 W Signal-to-noise ratio
531 – 1,602 kHz
(4 Ω at 1 kHz, 10% THD) More than 90 dB
(with the interval set at 9 kHz)
Dynamic range
Other models:
Inputs More than 90 dB
531 – 1,602 kHz
MD/VIDEO (AUDIO) IN: CD OPTICAL DIGITAL OUT
(with the interval set at 9 kHz)
(phone jacks) (Square optical connector jack, rear panel)
530 – 1,710 kHz
voltage 450 mV/250 mV, Wavelength 660 nm
(with the interval set at 10 kHz)
impedance 47 kΩ Output Level –18 dBm
Antenna
MIC: AM Loop antenna
(phone jack) Tape player section Antenna terminals
sensitivity 1 mV, Recording system External antenna terminal
impedance 10 kΩ 4-track 2-channel stereo Intermediate frequency
Frequency response (DOLBY NR OFF) 450 kHz
Outputs 40 – 13,000 Hz (±3 dB),
PHONES: using Sony TYPE I cassette — Continued on next page —
(stereo mini jack)
accepts headphones of 8 Ω or more
FRONT SPEAKER:
HCD-BX9:
accepts impedance of 6 to 16 Ω
COMPACT DISC DECK RECEIVER
HCD-DX9:
accepts impedance of 4 to 16 Ω

9-929-239-12 Sony Corporation

2001F0200-1 Home Audio Company
© 2001.6 Shinagawa Tec Service Manual Production Group

1
General
NOTES ON HANDLING THE OPTICAL PICK-UP
Power requirements
BX9 model: BLOCK OR BASE UNIT
230 V AC, 50/60 Hz
Australian model: The laser diode in the optical pick-up block may suffer electrostatic
230 - 240 V AC, 50/60 Hz
Mexican model: break-down because of the potential difference generated by the
120 V AC, 50/60 Hz charged electrostatic load, etc. on clothing and the human body.
Other models: During repair, pay attention to electrostatic break-down and also
120 V, 220 V or 230 - 240 V AC,
use the procedure in the printed matter which is included in the
50/60 Hz
Adjustable with voltage selector repair parts.
Power consumption The flexible board is easily damaged and should be handled with
HCD-BX9: 180 W care.
HCD-DX9: 300 W
Dimensions (w/h/d)
Approx. 280 × 360 × 425 mm NOTES ON LASER DIODE EMISSION CHECK
(11 × 14 3/16 × 16 11/16 in.)
Mas:
The laser beam on this model is concentrated so as to be focused on
HCD-DX9: Approx. 11 kg (24 lbs. 5 oz)
HCD-BX9: Approx. 9.5 kg (21 lbs.) the disc reflective surface by the objective lens in the optical pick-
Supplied accessories up block. Therefore, when checking the laser diode emission,
AM loop antenna (1) observe from more than 30 cm away from the objective lens.
Remote commander (1)
Batteries (2)
FM lead antenna (1) Laser component in this product is capable
Front speaker pads (8)
of emitting radiation exceeding the limit for
Design and specifications are subject to change Class 1.
without notice.

This appliance is classified as a CLASS 1 LASER product. The

CLASS 1 LASER PRODUCT MARKING is located on the rear
exterior.

CAUTION
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous radiation
exposure.

Notes on chip component replacement

• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.

Flexible Circuit Board Repairing

• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH

MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.

2
 TABLE OF CONTENTS
MODEL IDENTIFICATION
— BACK PANEL —
PARTS No.
1. SERVICE NOTE ······························································· 4
2. GENERAL ·········································································· 5
3. DISASSEMBLY ································································ 7
4. TEST MODE ···································································· 12
5. MECHANICAL ADJUSTMENTS ····························· 16
6. ELECTRICAL ADJUSTMENTS ······························· 16
7. DIAGRAMS
7-1. Circuit Board Location ····················································· 21
7-2. Block Diagrams ································································ 22
7-3. Printed Wiring Board – BD Section – ······························ 24
7-4. Schematic Diagram – BD Section – ································· 25
7-5. Printed Wiring Board – Main Section – ··························· 26
7-6. Schematic Diagram – Main (1/3) Section – ····················· 27
7-7. Schematic Diagram – Main (2/3) Section – ····················· 28
7-8. Schematic Diagram – Main (3/3) Section – ····················· 29
MODEL PARTS No. 7-9. Printed Wiring Board – Power AMP Section –
(BX9 model) ····································································· 30
BX9, DX9: MX models 4-225-041-4s 7-10. Schematic Diagram – Power AMP Section –
DX9: E, AR, SP, MY, EA, AUS models 4-225-041-5s (BX9 model) ····································································· 31
7-11. Printed Wiring Board – Power AMP Section –
(DX9 model) ····································································· 32
• Abbreviation 7-12. Schematic Diagram – Power AMP Section –
AUS : Australian model
EA : Saudi Arabia model (DX9 model) ····································································· 33
MY : Malaysia model 7-13. Printed Wiring Board – Panel Section – ··························· 34
SP : Singapore model 7-14. Schematic Diagram – Panel Section – ····························· 35
MX : Mexican model 7-15. Printed Wiring Board – Leaf SW Section – ···················· 36
AR : Argentina model
7-16. Schematic Diagram – Leaf SW Section – ························ 37
7-17. Printed Wiring Board – Driver Section – ························· 38
7-18. Schematic Diagram – Driver Section – ···························· 39
7-19. Printed Wiring Board – Trans Section –
(BX9 model) ····································································· 40
7-20. Schematic Diagram – Trans Section –
(BX9 model) ····································································· 41
7-21. Printed Wiring Board – Trans Section –
(DX9 model) ····································································· 42
7-22. Schematic Diagram – Trans Section –
(DX9 model) ····································································· 43
7-23. IC Pin Function Description ············································· 44
7-24. IC Block Diagrams ··························································· 46

8. EXPLODED VIEWS
8-1. Main Section ····································································· 49
8-2. Panel Section ···································································· 50
8-3. Main Board Section ·························································· 51
8-4. Tape Mechanism Deck Section ········································ 52
8-5. CD Mechanism Deck Section (CDM58-K2BD38) ·········· 53
8-6. Base Unit Section (BU-K2BD38) ···································· 54

9. ELECTRICAL PARTS LIST ······································· 55

3
 SECTION 1
SERVICE NOTE

Note for installing the panel board

2 Panel board

Hot melt

Screw hole
1 Cut the eleven melted-connection points with a cutting plier.
Attach the panel board with
six screws (+BVTP 2.6 × 8 )
after the board is removed once.
Do not tighten the screws excessively.

4
 SECTION 2
GENERAL

1 2 3 4 5 eg

wg
wf
wd 6

ws 7
wa 8 ef wh

9 ed wj

w; q; eh
qk qa es wk
ql
qj qs

qh qg qf qd ea e; wl

Photo: HCD-BX9

1 DISC SKIP EX-CHANGE button qk MIC LEVEL knob (DX9 model)

2 DISC 1 button and indicator ql V-GROOVE button and indicator
3 DISC 2 button and indicator w; CURSOL button and indicator
4 DISC 3 button and indicator wa GROOVE button
5 Z OPEN/CLOSE button ws EQ EDIT button
6 EDIT, TUNER MOMERY button wd SPECTRUM button
7 PLAY MODE, STEREO/MONO button wf DISPLAY button
8 REPEAT, DOLBY NR button wg ?/1 button and indicator
9 DIRECTION knob (DX9 model) wh TUNER/BAND button
DIRECTION, PTY knob (BX9 model) wj MD (VIDEO) button
q; SURROUND button wk Y button
qa VOLUME knob wl > + button
qs PHONES jack e; X button
qd ENTER button ea – . button
qf REC PAUSE/START button and indicator es x button
qg CD SYNC HI-DUB button ed TAPE A/B button
qh LOOP button (BX9 model) ef CD button
KARAOKE PON button (DX9 model) eg Function indicator
qj MIC jack (DX9 model) eh m/M knob

5
6
Step 1: Hooking up the system Inserting two size AA (R6)
(continued) 3 Press ENTER.
batteries into the remote Step 2: Setting the The minute indication flashes.
To attach the front speaker pads time
Attach the supplied front speaker pads to the
bottom of the speakers to stabilize the
speakers and prevent them from slipping. You must set the time before using the timer
functions.
e
instruction manual.

The clock is on a 24-hour system for the

E
E European model and a 12-hour system for
e
other models.
The 24-hour system model is used for
illustration purposes. 4 Press . or > repeatedly to set
This section is extracted from

Tip the minute.

With normal use, the batteries should last for about
six months. When the remote no longer operates
the system, replace both batteries with new ones. 5 Press ENTER.
1 The clock starts working.
Note
If you do not use the remote for a long period of Y X x

Positioning the speakers time, remove the batteries to avoid possible damage Tip
. >
Before you connect them, determine the best from battery leakage. 2,4 3,5 If you’ve made a mistake, start over from step 1.
location for your speakers. m M x
When carrying this system
N X
Do the following to protect the CD To change the time
1 Place the front speakers at an angle mechanism. The previous explanation shows you how to set the
of 45 degrees from your listening time while the power is off. To change the time
1 Make sure that all discs are removed from
position. while the power is on, do the following:
the unit.
1 Press CLOCK/TIMER SET.
Front Front 2 Hold down CD and then press ?/1 so that 2 Press . or > repeatedly to select
speaker speaker “LOCK” appears in the display.
(L) (R) SET CLOCK.
3 Unplug the AC power cord. 3 Press ENTER.
4 Perform steps 2 through 5 above.

45º
Note
Surround Surround The clock settings are canceled when you disconnect
speaker speaker the power cord or if a power failure occurs.
1 Press CLOCK/TIMER SET.
(L) (R)
The hour indication flashes.

2 Place the surround speakers facing

each other at about 60 to 90 cm
above your listening position.

Surround
speaker
60 to 90 cm
2 Press . or > repeatedly to set
the hour.

6 7
 SECTION 3
DISASSEMBLY
Note : Follow the disassembly procedure in the numerical order given.

9Two screws (+BVTP 3 × 10)

Upper case (Top)
3-1. UPPER CASE (TOP)

5Two screws (Case) q;

7Two screws
(+BVTP 3 × 10)

8
Claw

Side panel R
4

Side panel L
6Screw (Case)

3Two screws
(+BVTP 3 × 10)

1Two screws (Case)

2Screw (Case)

3-2. LOADING PANEL ASSY

Loading panel assy

CD mechanism deck (CDM58)

1 Turn the pulley to the direction of arrow.

Front panel side

pulley 3

2 Pull-out the disc tray.

7
3-3. FRONT PANEL SECTION

8Connector (CN201)
CD mechanism deck (CDM58)

4Screw (+BVTP 3 × 10)

Connector
(CN601)
1Flat type wire (CN304)

5Screw (+BVTP 3 × 10)

2Connector (CN1)

9Connector (CN202)
3Connector (CN2)

Front panel section

6Three screws (+BVTT 3 × 6)

3-4. TAPE MECHANISM DECK

4Bracket (Heart cam L)

3Screw (+BVTP 2.6 × 8)

5Five screws (+BVTP 2.6 × 8)

1Screw (+BVTP 2.6 × 8)

2Bracket (Heart cam R)

6Tape mechanism deck

8
3-5. PANEL BOARD

0Three claws

9Two screws
(+BVTP 2.6 × 8)
7Knob(MIC)

qaCD Switch board

6Spring

2Two screws qfPanel board

(+BVTP 2.6 × 8)

qdFive claws

3Two bosses & four pins

5FR knob qsCut the eleven melted-connection points with a cutting plier.
4Bracket (FR) Note: When attching the panel board,
refer to "Service Note" on page 4.
1Knob (Volume)

3-6. SUB-TRANS BOARD AND TRANS BOARD

8Panel, back
2Connector (CN974) 3Two screws
(+BVTP 3 × 8)
1Connector (CN975)

9Connector (CN975)
6Six screws
(+BVTP 3 × 10)
qfTrans board

0Connector (CN977)

qsTwo screws
(+BVTT 4 × 8)
qaTwo screws (+BVTT 4 × 8)
qdTrans 4Sub-trans 5Two screws
board (+BVTP 3 × 10)

7Connector (CN891)

9
3-7. MAIN BOARD AND AMP BOARD

4Three screws (+BVTP 3 × 8) 7Heat sink

6Two screws (+BVTP 3 × 8)

5Power AMP board

Connector(CN502)
3Two screws (+BVTP 3 × 16)

Connector
(CN503)

2Main board

1Two screws (+BVTP 3 × 8)

3-8. LEAF SW BOARD, HEAD (A) BOARD AND HEAD (B) BOARD

1Five claws
2Leaf SW board

6Remove the four solderings.

4Head (A) board

5Head (B) board

3Screw (+PS 2.6 × 5)

6Screw (+PS 2.6 × 5)

10
3-9. BASE UNIT

3
4Two insulators
Base unit

1Flat type wire (CN101)

5Two insulators

2Four screws (+PTPWH 2.6)

3-10. DRIVER BOARD, MOTOR BOARD AND SENSOR BOARD

9Screw (+PTPWH 2.6 × 8)

4Three screws (+BVTP 2.6 × 8)

6Motor board

7Flat type wire (CN721)

5Remove the two solderings of motor.

qaScrew (+BVTP 2.6 × 8)
q;Tray 8Connector(CN722)
2Driver board
qsSensor board

3Connector (CN701)

1Screw (+BVTP 2.6 × 8)

11
 SECTION 4
TEST MODE
[MC Cold Reset] [Change-over of MW Tuner Step between 9 kHz and
• The cold reset clears all data including preset data stored in the 10 kHz]
RAM to initial conditions. Execute this mode when returning • A step of MW channels can be changed over between 9 kHz
the set to the customer. and 10 kHz.
Procedure: Procedure:
1. Press three buttons x , ENTER , and ?/1 simulta-neously. 1. Press ?/1 button to turn the set ON.
2. The fluorescent indicator tube displays “COLD RESET” and 2. Select the function “TUNER”, and press TUNER/BAND
the set is reset. button to select the BAND “MW”.
3. Press ?/1 button to turn the set OFF.
[CD Ship Mode] 4. Press ENTER and ?/1 buttons simultaneously, and the display
• This mode moves the pickup to the position durable to vibra- of fluorescent indicator tube changes to “MW 9 k STEP” or
tion. Use this mode when returning the set to the customer after “MW 10 k STEP”, and thus the channel step is changed over.
repair.
Procedure: [GC Test Mode]
1. Press ?/1 button to turn the set ON. • This mode is used to check the software version, FL tube, LED,
2. Press CD button and ?/1 button simultaneously. keyboard and VACS.
3. After the "STANDBY" display blinks six times, a message Procedure:
“LOCK” is displayed on the fluorescent indicator tube, and the 1. Press three buttons x , ENTER , and DISC 2 simultaneously.
CD ship mode is set. 2. LEDs and fluorescent indicator tube are all turned on.
3. When you want to enter the software version display mode,
[MC Hot Reset] press DISC 1 . The model number and destination are displayed.
• This mode resets the set with the preset data kept stored in the 4. Each time DISC 1 is pressed, the display changes starting
memory. The hot reset mode functions same as if the power from MC version, GC version, VC version, CD version, CM
cord is plugged in and out. version, ST version, TC version, TA version, TM version and
Procedure: BR version in this order, and returns to the model number and
1. Press three buttons x , ENTER , and DISC 1 simultaneously. destination display.
2. The fluorescent indicator tube becomes blank instantaneously, 5. When DISC 3 is pressed while the version numbers are being
and the set is reset. displayed except model number and destination, year, month
and day of the software creation appear. When DISC 3 is
[CD Service Mode] pressed again, the display returns to the software version display.
• This mode can run the CD sled motor freely. Use this mode, for When DISC 1 is pressed while year, month and day of the
instance, when cleaning the pickup. software creation are being displayed, the year, month and day
Procedure: of creation of the software versions are displayed in the same
1. Press ?/1 button to turn the set ON. order of version display.
2. Select the function “CD”. 6. Press DISC 2 button, and the key check mode is activated.
3. Press three buttons x , ENTER , and OPEN/CLOSE simul- 7. In the key check mode, the fluorescent indicator tube displays
taneously. “KEY0 VOL0”. Each time a button is pressed, “KEY” value
4. The CD service mode is selected. increases. However, once a button is pressed, it is no longer
5. With the CD in stop status, turn the shuttle knob clockwise to taken into account.
move the pickup to outside track, or turn the shuttle knob “VOL” value increases like 1, 2, 3 ... if rotating VOLUME
counter-clockwise to inside track. knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in
6. To exit from this mode, perform as follows: “–” direction.
1) Move the pickup to the most inside track. 8. Also when DISC 3 is pressed after lighting of all LEDs and FL
2) Press three buttons in the same manner as step 2. tubes, value of VACS appears.
Note: • Always move the pickup to most inside track when exiting from 9. To exit from this mode, press three buttons in the same manner
this mode. Otherwise, a disc will not be unloaded. as step 1, or disconnect the power cord.
• Do not run the sled motor excessively, otherwise the gear can be
chipped.

[VACS ON/OFF Mode]

• This mode is used to switch ON and OFF the VACS (Variable
Attenuation Control System).

Procedure:
Press the ENTER and SPECTRUM buttons simultaneously. The
message “VACS OFF” or “VACS ON” appears.

12
[MC Test Mode]
• This mode is used to check operations of the respective sections
of Amplifier, Tuner, CD and Tape.

Procedure:
1. Press the ?/1 button to turn on the set.
2. Press the three buttons of x , ENTER and DISC 3
simultaneously.
3. A message “TEST MODE” appears on the FL display tube.
4 When f (CURSOR UP) button is pressed, GEQ increases to
its maximum and a message “GEQ ALL MA” appears.
5. When F (CURSOR DOWN) button is pressed, GEQ decreases
to its minimum and a message “GEQ ALL M1” appears.
6. When g (CURSOR LEFT) or G (CURSOR RIGHT) button
is pressed, GEQ is set to flat and a message “GEQ FLAT”
appears.
7. When the VOLUME control knob is turned clockwise even
slightly, the sound volume increases to its maximum and a
message “VOLUME MAX” appears for two seconds, then the
display returns to the original display.
8. When the VOLUME control knob is turned counter-clockwise
even slightly, the sound volume decreases to its minimum and
a message “VOLUME MIN” appears for two seconds, then
the display returns to the original display.
9. In the test mode, the default-preset channel is called even when
the TUNER is selected and an attempt is made to call the preset
channel that has been stored in memory, by operating the Shuttle
knob. (It means that the memory is cleared.)
10. When CD is selected and the EDIT button is pressed, the disc
that is being chucked at this moment becomes the default
setting. It means that the default disc only is accessed when
any other discs are selected even though the display indication
changes accordingly. At the same time, the DISC SKIP EX-
CHANGE and OPEN/CLOSE cannot be accepted. (It means
that the tray motor and the turntable motor are disabled of their
operation.)
11. When a tape is inserted in Deck B and recording is started, the
input source function selects VIDEO automatically.
12. When x button is pressed to stop recording, the Tape (Deck)
B is selected and tape is rewound using the Shuttle knob, tape
is rewound, tape is stops at around the record-starting position
and playback of the recorded portion of the tape is started. If
PAUSE is inserted even once during recording, tape is rewound
to the position around the PAUSE position and is played back.
13. When the CD SYNC HI-DUB Button is press during playback
of Deck B, either normal speed or high speed can be selected
by this button.
14. Select the desired loop by pressing the PLAY MODE button.
Insert a test tape AMS-110A or AMS-RO to Deck A.
15. Press the SPECTRUM button to enter the AMS test mode.
16. After a tape is rewound first, the FF AMS is checked, and the
mechanism is shut off after detecting the AMS signal twice.
17. Then the REW AMS is checked and the mechanism is shut off
after detecting the AMS signal twice.
18. When the check is complete, a message of either OK or NG
appears.
19. When you want to exit this mode, press the ?/1 button twice.
The cold reset is enforced at the same time.

13
[Aging Mode]
This mode can be used for operation check of CD section and tape deck section.
• If an error occurred:
The aging operation stops and display status.
• If no error occurs:
The aging operation continues repeatedly.

1. Operating method of Aging Mode

Turn on the main power and select “CD” of the function.
1) Set a disc in DISC1 tray. Select ALL DISC CONTINUE, and REPEAT OFF.
2) Load the tapes recording use into the decks A and B respectively.
3) Press three buttons x , ENTER , and
DISC SKIP/EX-CHANGE simultaneously.
4) Aging operations of CD and tape are started at the same time.
5) To exit the aging mode, perform [MC Cold Reset].

3. Aging Mode in CD section

1) Display state
• No error occurs Display

AGING[*][*][*][*]

Note:
[*][*][*][*] : Number of aging operations

Error display

E ** s ## $$ %%
12 3 4 5
1 ** The error No. 00 indicates the newest error. As the error No. increases, it means the older error.
When you want to retrieve the error history, press the PLAY MODE button in the case of mechanism error.
Or press the REPEAT button in the case of NO DISC error.
2 s M: Mechanism error D: No disc error
3 ## Don’t care 01: FOCUS ERROR
02: GFS ERROR
03: SETUP ERROR
4 $$ High order digits only 01: NO DISC judgment without chucking retry
D: Stopped during closing due to problems other than mechanism. 02: NO DISC judgment after chucking retry
E: Stopped during opening due to problems other than mechanism.
C: Stopped during chucking due to problems other than mechanism.
F: Stopped during EX-opening due to problems other than mechanism.
5 %% Emergency related errors (High order digits only) Status at the time of NO DISC judgment
1: Stopped during chuck-up (High order digits only)
2: Stopped during chuck-down 1: STOP
3: Time out by EX-OPEN 2: SETUP
5: Time out by EX-CLOSE 3: TOC READ
4: ACCESS
5: PLAY BACK
6: PAUSE
7: MANUAL SEARCH (PLAY)
8: MANUAL SEARCH (PAUSE)

• When the buttons x , ENTER and DISC 1 are pressed simultaneously, number of time of the mechanism error and the NO DISC error
can be checked.
Display: EMC**EDC** **: Number of times of error (Maximum three times)
EMC: Mechanism error
EDC: NO DISC error

• When aging operation is complete, be sure to perform the MC Cold Reset to reset the error history.

14
2) Operation during aging mode
In the aging mode, the program is executed in the following
sequence.
(1) The disc tray opens and closes.
(2) The mechanism accesses DISC 2 and makes an attempt to
read TOC. However, since there are no discs, a message
“CD2 NO DISC” appears.
(3) The mechanism accesses DISC 3 and a message “CD3 NO
DISC” appears.
(4) The disc tray turns to select a disc1.
(5) A disc is chucked.
(6) TOC of disc is read.
(7) The pickup accesses to the track 1, and playing 2 seconds.
(8) The pickup accesses to the last track, and playing 2 seconds.
(9) Every time when an aging operation of step 1 to step 8 is
complete, the display “AGING[*][*][*][*]” value increases
as the number of aging operations is counted up.
(10) Returns to step 1.

3. Aging Mode in Tape Deck section

1) Display state
• No error occurs
Display action now
• Error occurred
Display action last time

NO. Display action Action contents Final timing

1 TAPE A AG-1 Rewind the TAPE A, B The top of tape
2 TAPE A AG-2 FWD play the TAPE A 2 minutes playing
3 TAPE A AG-3 F.F. the TAPE A 20 second FF or the end
of tape
4 TAPE A AG-4 REV play the TAPE A 2 minutes playing
5 TAPE A AG-5 Rewind the TAPE A The top of tape
6 TAPE B AG-2 FWD play the TAPE B 2 minutes playing
7 TAPE B AG-3 F.F. the TAPE B 20 second FF or the end
of tape
8 TAPE B AG-4 REV play the TAPE B 2 minutes playing
9 TAPE B AG-5 Rewind the TAPE B The top of tape

2) Operation during aging mode

In the aging mode, the program is executed in the following
sequence.
(1) Rewind is executed up to the top of tape A and B.
(2) A tape on FWD side is played for 2 minutes.
(3) FF is executed up to either made for 20 second or the end of
tape.
(4) A tape is reversed, and the tape on REV side is played for 2
minutes.
(5) Rewind is executed up to the top of tape.
(6) Returns to step 2, and repeat steps from 2 to 5.

[Function Change Mode]

* elect either VIDEO or MD of the external FUNCTION input.

Procedure:
1. Turn on the power.
2. Press the two buttons ENTER and ?/1 at the same time.
The main power is turned on and the other function of the
previous function is selected and displayed. “MD” or
“VIDEO”.

15
 SECTION 5 SECTION 6
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS
Precaution
DECK SECTION 0 dB=0.775 V
1. Clean the following parts with a denatured alcohol-moistened
swab: 1. Demagnetize the record/playback head with a head
record/playback heads pinch rollers demagnetizer.
erase head rubber belts 2. Do not use a magnetized screwdriver for the adjustments.
capstan idlers 3. After the adjustments, apply suitable locking compound to the
2. Demagnetize the record/playback head with a head parts adjust.
demagnetizer. 4. The adjustments should be performed with the rated power
3. Do not use a magnetized screwdriver for the adjustments. supply voltage unless otherwise noted.
4. After the adjustments, apply suitable locking compound to the 5. The adjustments should be performed in the order given in this
parts adjusted. service manual. (As a general rule, playback circuit adjustment
5. The adjustments should be performed with the rated power should be completed before performing recording circuit
supply voltage unless otherwise noted. adjustment.)
6. The adjustments should be performed for both L-CH and R-
Torque Measurement CH.
Mode Torque meter Meter reading 7. Switches and controls should be set as follows unless otherwise
specified.
3.06 N • m to 6.96 N • m
FWD CQ-102C 31 to 71 g • cm
• Test Tape
(0.43 – 0.98 oz • inch)
0.19 N • m to 0.58 N • m Tape Signal Used for
FWD CQ-102C 2 to 6 g • cm P-4-A100 10 kHz, –10 dB Azimuth Adjustment
back tension
(0.02 – 0.08 oz • inch) WS-48B 3 kHz, 0 dB Tape Speed Adjustment
3.06 N • m to 6.96 N • m P-4-L300 315 Hz, 0 dB Level Adjustment
REV CQ-102RC 31 to 71 g • cm
(0.43 – 0.98 oz • inch)
Record/Playback Head Azimuth Adjustment
0.19 N • m to 0.58 N • m
REV CQ-102RC 2 to 6 g • cm DECK A DECK B
back tension
(0.02 – 0.08 oz • inch)
Note: Perform this adjustments for both decks
6.96 N • m to 14.02 N • m
Procedure:
FF/REW CQ-201B 71 to 143 g • cm
1. Mode: Playback
(0.98 – 1.99 oz • inch)
9.80 N • m
test tape main board
FWD tension CQ-403A 100 g or more P-4-A100 CN301
(3.53 oz or more) (10 kHz, –10 dB) Pin 3 (L-CH)
9.80 N • m Pin 1 (R-CH) level meter
REV tension CQ-403R 100 g or more
set
(3.53 oz or more) +
–
main board
CN301
Pin 2 (GND)

16
2. Turn the adjustment screw and check output peaks. If the peaks Tape Speed Adjustment DECK B
do not match for L-CH and R-CH, turn the adjustment screw Note: Start the Tape Speed adjustment as below after setting to the test
so that outputs match within 1dB of peak. mode.
In the test mode, the tape speed is high during pressing the
CD SYNC HI-DUB button.
Procedure:
within 1. Turn the power switch on.
L-CH 1dB 2. Press the x button, ENTER button and DISC 3 button
peak
within simultaneously.
Output 1dB (The “TEST MODE” on the fluorescent indicator tube display
level
while in the test mode.)
To exit from the test mode, press the ?/1 button.
R-CH Mode: Playback
peak
Screw Screw test tape
position L-CH R-CH position WS-48B frequency counter
peak peak (3 kHz, 0 dB)

set +
3. Mode: Playback –
test tape main board
P-4-A100
(10 kHz, –10 dB) oscilloscope CN301 (Pin 3 : L-CH)
pin 3 (Pin 1 : R-CH)
L-CH
pin 2
MAIN L 1. Insert the WS-48B into the deck B.
board V H
CN301 2. Press the gG button on the deck B.
set R 3. Press the CD SYNC HI-DUB button in playback mode.
Then at HIGH speed mode.
R-CH
4. Adjust RV1001 on the LEAF SW board do that frequency
pin 1
counter reads 6,000 ± 30 Hz.
waveform of oscilloscope
5. Press the CD SYNC HI-DUB button.
Then back to NORMAL speed mode.
6. Adjust RV1002 on the LEAF SW board so that frequency
in phase 45 ° 90 ° 135 ° 180 ° counter reads 3,000 ± 15 Hz.
Adjustment Location: LEAF SW board
good wrong

Playback level Adjustment DECK A DECK B

4. After the adjustments, apply suitable locking compound to the Procedure:
pats adjusted. Mode: Playback

test tape
Adjustment Location: Playback Head (Deck A). P-4-L300 level meter
Record/Playback/Erase Head (Deck B). (315 Hz, 0 dB)

set +
–

main board
CN301 (Pin 3 : L-CH)
(Pin 1 : R-CH)

Deck A is RV302 (L-CH) and RV352 (R-CH), Deck B is RV303

(L-CH) and RV353 (R-CH) so that adjustment within adjustment
level as follows.
Adjustment Level:
CN301 PB level: 301.5 to 338.3 mV (–8.2 to –7.2 dB) level
difference between the channels: within ±0.5 dB
Adjustment Location: MAIN board

Sample Volue of Wow and Flutter: 0.3% or less W. RMS

(WS-48B)

forward
reverse

17
REC Bias Adjustment DECK B 4. Mode: Record
Procedure:
INTRODUCTION MD/VIDEO (AUDIO) IN
When set to the test mode performed in Tape Speed Adjustment, 315 Hz, 50 mV (–23.8 dB)
when the tape is rewound after recording, the “REC memory mode” AF OSC
blank tape
which rewinds only the recorded portion and playback is set. 600 Ω CS-123
This “REC memory mode” is convenient for performing this attenuator
adjustment. During recording, the input signal FUNCTION will set
automatically switch to VIDEO.
(If do not operation of stopped from recording complete, and rotette
of shuttle knob then rewind to recording start position.) 5. Mode: Playback

1. Press MD/VIDEO button to select VIDEO. (This step is not recorded level meter
portion
necessary if the above test mode has already been set.)
2. Insert a tape into deck B. +
3. After press REC PAUSE/START button, press REC PAUSE/ set
–
START button, then recording start.
4. Mode: Record CN301 (Pin 3 : L-CH)
(Pin 1 : R-CH)

6. Confirm playback the signal recorded in step 3 become

MD/VIDEO (AUDIO) IN adjustable level as follows.
1) 315 Hz  50 mV (–23.8 dB) If these levels do not adjustable level, adjustment the RV301

2) 10 kHz  (L-CH) and RV351 (R-CH) on the MAIN board to repeat steps
AF OSC blank tape 4 and 5.
600 Ω CN-123 Adjustable level:
attenuator CN301 PB level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)
set Adjustment Location: MAIN board

5. Mode: Playback [MAIN BOARD] (Component Side)

recorded level meter

portion

set +
T601
–
REC LEVEL (L)
CN301 (Pin 3 : L-CH) RV611 (B) PB LEVEL (R)
(Pin 1 : R-CH) (A)

CN304
6. Confirm playback the signal recorded in step 3 become CN301

adjustable level as follows. PB LEVEL (L) 3 1 RV301

(A)
If these levels do not adjustable level, adjustment the RV304 PB LEVEL (R)
RV352
CN302
(L-CH) and RV354 (R-CH) on the AUDIO board to repeat steps (B)
RV302
RV353
4 and 5. RV351 RV303

Adjustable level: Playback output of 315 Hz to playback output REC LEVEL (R)
CN303
PB LEVEL (L)
of 10 kHz: ±1.0 dB (B) (B) RV304
Adjustment Location: MAIN board REC LEVEL (L)
(A) REC LEVEL (R) RV354

REC Level Adjustment DECK B (A)

Procedure:
INTRODUCTION [LEAF SW BOARD] (Component Side)
When set to the test mode performed in Tape Speed Adjustment,
TAPE SPEED
when the tape is rewound after recording, the “REC memory mode”











which rewinds only the recorded portion and playback is set. (NORMAL) (HIGH)
This “REC memory mode” is convenient for performing this
adjustment. During recording, the input signal FUNCTION will RV1002 CN1001
RV1001
automatically switch to VIDEO.
(If do not operation of stopped from recording complete, and rotate
of shuttle knob then rewind to recording start position.)

1. Press MD/VIDEO button to select VIDEO. (This step is not

necessary if the above test mode has already been set.)
2. Insert a tape into deck B.
3. After press REC PAUSE/START button, press REC PAUSE/
START button, then recording start.

18
FM Tuned Level Adjustment CD SECTION
FM RF SSG Note :
75 Ω coaxial 1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10MΩ impedance.
set 4. Clean the object lens by an applicator with neutral detergent
Carrier frequency : 98 MHz when the signal level is low than specified value with the
Modulation : AUDIO 1 kHz, 75 kHz FM ANTENNA terminal following checks.
deviation (100%) (TM601)
Output level : 28 dB (at 75 W open)
S-Curve Check

Procedure: Oscilloscope
1. Supply a 28 dB 98 MHz signal from the ANTENNA terminal. BD board
2. Tune the set to 98 MHz.
3. Adjust RV611 to the point (moment) when the TUNED TP(FEO)
indicator will change from going off to going on. TP(VC)

Adjustment Location: MAIN board Procedure :

1. Connect oscilloscope to TP (FEO).
Null Adjustment 2. Connect between TP (FEI) and TP (VC) by lead wire.
3. Connect between TP (AGCCON) and TP (GND) by lead wire.
FM RF SSG 4. Turn Power switch on.
5. Load a disc (YEDS-18) and actuate the focus search. (In
75 Ω coaxial consequence of open and close the disc tray, actuate the focus
search)
6. Confirm that the oscilloscope waveform (S-curve) is
set symmetrical between A and B. And confirm peak to peak level
Carrier frequency : 98 MHz within 4 ±1 Vp-p.
Modulation : AUDIO 1 kHz, 75 kHz FM ANTENNA terminal
deviation (100%) (TM601) S-curve waveform
Output level : 60 dB (at 75 W open)
symmetry

Procedure:
1. Supply a 60 dB 98 MHz signal from the ANTENNA terminal. A
2. Tune the set to 98 MHz.
within 4 ±1Vp-p
3. Measure voltage between pin 21 of IC 601. Adjust T601 ubtil
B
the voltage becomes 0 V.

Adjustment Location: MAIN board 7. After check, remove the lead wire connected in step 2 and 3.
Note : • Try to measure several times to make sure than the ratio
of A : B or B : A is more than 10 : 7.
Adjustment Location • Take sweep time as long as possible and light up the
brightness to obtain best waveform.
[MAIN BOARD] Component side
RF Level Check

NULL
oscilloscope
BD board
FM TUNED LEVEL
T601
TP(RF)
TP(VC)
RV611

Procedure :
CN304 1. Connect oscilloscope to TP (RF).
CN301
2. Connect between TP (AGCCON) and TP (GND) by lead wire.
3 1 RV301
3. Turned Power switch on.
RV352
RV302 CN302 4. Load a disc (YEDS-18) and playback.
RV353 5. Confirm that oscilloscope waveform is clear and check RF signal
RV351 RV303
level is correct or not.
CN303
6. After check, remove the lead wire connected in step 2.
RV304

RV354

19
Note: Clear RF signal waveform means that the shape “◊” can be Adjustment Location:
clearly distinguished at the center of the waveform.
[BD BOARD] (Conductor Side)
RF signal waveform
VOLT/DIV : 200mV
TIME/DIV : 500ns

level : 1.45 ± 0.3Vp-p

E-F Balance (1 Track jump) Check

oscilloscope
BD board TP
TP
(XPCK)
(AGCCON)
TP (TEO) + 12
TP (VC) – 1 21 20
TP IC103
(TEO) 24
40 1
TP IC101
Procedure: 41 80
(FEO)
1. Connect oscilloscope to TP (TEO) and TP (VC) board. TP
2. Turned Power switch on. TP (FEI)
60 61
3. Load a disc (YEDS-18) and playback the number five track. (VC)
4. Press the Y button. (Becomes the 1 track jump mode.)
5. Confirm that the level B and A (DC voltage) on the oscilloscope TP
waveform. (RF) TP
(DGND)
1 track jump waveform
Center of
waveform

A (DC voltage)
0V

level=1.3±0.6Vp-p Symmetry

Specification level: A x 100=less than ±22%

B

6. After check, remove the lead wire connected in step 1.

RF PLL Free-run Frequency

Procedure :
1. Connect frequency counter to test point (XPCK) with lead wire.

BD board frequency counter

TP (XPCK) +
–

2. Turned Power switch on.

3. Put the disc (YEDS-18) in to play the number five track.
Confirm that reading on frequency counter is 4.3218MHz.

20
 HCD-BX9/DX9
SECTION 7
DIAGRAMS
7-1. CIRCUIT BOARD LOCATION
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
MOTOR Board DRIVER Board
Note on Schematic Diagram: Note on Printed Wiring Boards:
• All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side. SENSOR Board
50 WV or less are not indicated except for electrolytics • b : Pattern from the side which enables seeing. SUB-TRANS Board
and tantalums. • Indication of transistor. TRANS Board
• All resistors are in Ω and 1/4 W or less unless otherwise BD Board
specified. C
• f : internal component.
• C : panel designation. These are omitted. Q
CD SWITCH Board
B E
Note: The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.

• U : B+ Line. Q
• V : B– Line.
• H : adjustment for repair. B C E
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions. These are omitted.
• Voltages are taken with a VOM (Input impedance 10 MΩ).
PANEL Board
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
MAIN Board
tion tolerances.
• Circled numbers refer to waveforms.
LEAF SW Board
• Signal path.
F : FM
f : AM
E : PB (DECK A)
d : PB (DECK B) POWER AMP Board
G : REC (DECK B)
J : CD HEAD (A) Board
c : digital out
• Abbreviation
HEAD (B) Board
AUS : Australian model
G : German model
EA : Saudi Arabia model
• WAVEFORMS
MY : Malaysia model
SP : Singapore model
MX : Mexican model – BD BOARD – – MAIN BOARD –
AR : Argentina model
AED : North European model 1 IC101 yj 3 IC101 ra 1 IC401 qa 3 T301 4
CD PLAY MODE CD PLAY MODE STOP MODE TAPE B REC MODE

approx 200mVp-p
6.4Vp-p 3.0Vp-p 80.7kHz 120Vp-p
16.9344MHz 32.768kHz

2 IC101 ta 4 IC101 el 2 IC401 qd

CD PLAY MODE CD PLAY MODE STOP MODE

approx 170mVp-p

16MHz 3.4Vp-p
400nsec/div 1.2Vp-p

– PANEL BOARD –
1 IC601 oa
STOP MODE

12.5MHz 4.8Vp-p

21 21
HCD-BX9/DX9
DX9 MODEL
AM/FM IF MPX
TM601 FE601 Q602 IC601 LPF601
7-2. BLOCK DIAGRAMS CF601 RF IF CF602 BUFFER L-CH • RCH is omitted
– TUNER/CD SECTION – 1 ANT IN IF OUT 7
AMP
1 FM IF L OUT 11
Q611
LPF A • Signal Path
FM 75Ω OSC OUT 8
MAIN
VT 5 R OUT 10 R-CH SECTION : FM
Q602 (Page 23)
G +B A+12V : CD
AM IF IN 18
IFT601
AM PLL : DIGITAL OUT
IC651
AM MIX OUT 19
10 FM FM/AM IF 12 9 IF OUT
FM 7 12 AM/IF FM SD ADJ 3
1 XIN AM OSC 14 24 AM OSC RV611 BX9
BX9 MODEL X651 MODEL
VCO STOP 2 13 VCO STOP
FE603 4.5MHz RDS
24 XOUT IF REQ 8 8 IF REQ MUTE IC682 MASTER CONTROL
IC681 IC401(1/2)
1 ANT IN IF OUT 7 3 1
R601 FM/AM DET 16 4 MUX
DO
OSC OUT 8 15 FM OSC DO 6
DI DATA 2 21 RDS DATA
VT 5 18 VT1 IN DI 4 14 XO
CL XT681 INT 16 20 RDS INT
17 VT1 CL 5 4.332MHz
CE
19 PD1 CE 3 13 XI

20 AM RF IN
RB641 13 14
1 4 11 15 9
22 AM OSC TUNED 6 24 TUNED
5
STEREO 17 23 STEREO
3 6 7
23 V REG

22 ST MUTE
2 12
DO
27 ST DIN
DI
26 ST DOUT
CL
28 ST CLK
CE
25 ST CE

OPTICAL PICK-UP DIGITAL SERVO

DIGITAL SIGNAL PROC.
BLOCK RF AMP D/A CONV. IC201
(KSM-213DAP) IC103 IC101
OPTICAL CD
VC 12 VC D OUT 60 DIGITAL
OUT DIGITAL OUT
+5V
A
5 A RFO 16 51 RFAC
B
6 B RFI 17 43 RFDC
C L OUT
D
7 C L OUT 72 B IC701
8 D FE 14 39 FE
E MAIN
11 E TE 13 41 TE R OUT 75 R-CH SECTION MTR CNT2 44 9 4
F MOTOR M721
10 F 40 SE (Page 23) DRIVE
M TURN
Q101 MOTOR
MTR CNT1 45 7 2
LD LD
3 LD LD ON 22 14 XLON DATA 5 33 CD DATA
DRIVE
CLOK 7 37 CD CLK
GND XLAT 6 42 XLT
IC711
HOLD SW 21 SQCK 2 33 SQ CLK
TBL ADDRESS
SCLK 9 T SENS 49
PD SENSOR
4 PD SCOR 20 19 SCOR
VR SQSO 1 32 SQ DATA
IC102
MOTOR/COIL DRIVE
F+ S101 OPEN SW 46 S701
13 CH1RO CH1RI 3 32 FFDR SSTP 27 LIMIT OPEN/CLOSE
FOCUS IN SW CLOSE SW 47
COIL F-
14 CH1FO CH1FI 2 33 FRDR
S711
XTAI 66 BU UP/DOWN SW 48 BU UP/
T+ X101 DOWN
11 CH2RO CH2RI 6 30 TFDR
TRACKING 16.9344MHz
XTAO 67
COIL T-
12 CH2FO CH2FI 5 31 TRDR
09

18 CH3RO CH3RI 23 29 SRDR

M102
SLED M
MOTOR
17 CH3FO CH3FI 24 28 SFDR
XRST 3 43 XRST
16 CH4RO CH4INS 25 26 MDP
M101
SPINDLE M
MOTOR
15 CH4FO 41 HOLD
MUTE 20

22 22
 HCD-BX9/DX9

– MAIN SECTION –

J102
SURROUND
SPEAKER
INPUT SELECT R CH
TONE/VOL CONT
IC101
IC102 IC501 TM801
TUNER L-CH 5
SECTION A 40 IN2A VOL OUT2 24
6
7
15 POWER 11 L
(Page 22) Q504,505 AMP Q861 Q821,822
RY801
SPEAKER
CD Q824,825
LOUT MUTE MUTE MUTE MUTE PROTECT R CH R
SECTION B 38 IN2C
CONT Q103 12 CONT Q862 DETECTOR RELAY
(Page 22) Q101,102
DRIVE

Q551 Q823 Q828,829

J101 DBFB D841 D502
REF 1 OVER LOAD PROTECT PROTECT
L-CH CONT
L 37 IN2D DETECTOR CONT SWITCH R CH
MD/VIDEO Q503,504 J631
(AUDIO) Q503 MUTE MUTE +B Q506,506 PHONS
R R-CH
DBFB CONT Q581 OVER HEAT
SWITCH DETECTOR

Q891,892 FAN
DECK PROC. FAN
IC301 DRIVE
PB EQ
DECK-A AMP
RV302 REC
IC303 43 35 INVOL OUT2
FL601
48 REC
DOLBY FLOURESCENT
PB B
70 INDICATOR TUBE
HEAD A PB DISPLAY CONTROL
PB EQ DOL PB IC601
R-CH AMP 40 39 IN2B
RV303 PAS
IC304 B 3 HEADPHONE
120 F1 F2
46 50
.
21 DATA P1
REC/PB SWITCH 52
DECK-B IC302 22 CLOCK Q615 IC602 P35
85 Q606-614
+5.6V 17 20 BPF 0 49
1 +7V REG 10 SPEANA G1 LED
BPF 12 25 BPF 5 G17 33 DRIVER
6
REC/PB 2 SWITCH 11 26 ALL BAND
4 R-CH DX9 MODEL 5
HEAD Q304,305 Q630-635
RV722 4
PLAY1-3 10 LED
R-CH 3 MIC 3 DRIVER D630-632
EXIST1-3 5
R CH VOL
C332,L301 J721 IC722 IC722
S617,618
BIAS REC MIC 1 S623-628,630-636
TRAP 36 38 39 GROOVE LED 11
RV304 EQ FUCTION D611-615
KEY 17 KEY0 FILE LED 12 D617,618

B NORM/CROM/METAL
R-CH REC RV301 Q621-626
BIAS BASS SHIFT LED 13
REC(L) EA MODEL S611-616 LED
S619-621,626,629 FUNCTION LED 14 DRIVER
LEVEL

REC /PB/PASS
T301 TA+12V

BIAS ON/OFF
IC721 REC/PAUSE LED 15

NORM/HIGH
ALC ON/OFF
FUCTION

RM ON/OFF
BIAS

LM ON/OFF
NR ON/OFF
NORM KEY 18 KEY1
OSC RV721

A120/70
33

MS OUT
BIAS J722 SURROUND LED 16

PB A/B
ERASE Q302,303 CROM SW ECHO Q604
Q301 32 MIC 2 2 6 S637-646
HEAD LEVEL LED D601
FUCTION POWER LED 28 DRIVER
17 19 16 18 15 20 22 23 24 25 26 ECHO KEY 19 KEY2 POWER
LEVEL
Q141 Q605
D602
DC LED
+6V BIAS
A+12V S601 1 VOL A TIMER LED 27 DRIVER TIMER
TC BLOCK VOLUME SELECT
2 VOL B
A120/70
B120/70 SIRCS
100 SIRCS
A HALF D822 IC603 XIN 89
B HALF X601
12.5MHz
A PLAY 97 I2C DATA XOUT 90
B PLAY 98 I2CCLOCK
A SHUT 96 WAKE UP
B SHUT X401 X402 92 RESET
32.768kHz 16MHz
Q941
-V
91 90 69 68 93 67 79 77 76 78 75 74 73 72 71 70 4 5 10 11 15 13 83 84 100 87 82 30 29 18 7 -B
Q393,394 REG
B HALF
A HALF

DBFB ON/OFF
REC MUTE
B PLAY
A PLAY

NR ON/OFF

DATA

IIC CLK
TC RELAY

ALC

CLK

WAKE UP
TC MUTE

X IN
EQ H/N

BIAS

X OUT

LINE MUTE

AC CUT
B SHUT
A SHUT

R/PB PAS

XC OUT
PB A/B

STK MUTE

RELAY H
PROTECT

IIC DATA
XC IN
AMS IN

A TRIG
A TRG M+ 57 A TRIG
DRIVE
D541 F974 T971
Q391,392
B TRIG IC911 Q911,912 BX9,AUS
B TRG M+ 58 B TRIG CD D+5V +B
DRIVE +5V CD POWER EXCEPT MX MODEL
CD A+5V 3 1 POWER F975
Q395 REG SWITCH AMP F973 JW9073
MASTER CONTROL -B
CAP MOTOR IC401(2/2) EXCEPT BX9,AUS,MX
CAP M H/L 59 CAP M H/L CD POWER 85 MODEL
SPEED CONT D901-904 S951
D952 IC951 F972

STBY RELAY
Q396,397 RDS D+5V UNSW
D953 +5V AC
CAP MOTOR AUDIO +5V 3 1

RESET
CAP M+ 60 CAP M CONT REG IN
09 DRIVE A+12V
TC A+12V D511 DX9
81 12 IC921 F971 JW9071 MODEL
MIC A+12V
+12V EXCEPT BX9,AUS AUS MODEL
ST A+12V 3 1
REG
IC501 D906-909
Q501 IC961
RESET +9V
TC M+9V 3 1
REG

• RCH is omitted IC931

CD M+7V
+7V F1
• Signal Path LED +7V 3 1
REG
F2
: PB (DECK A)
BX9 MODEL

: PB (DECK B)
D972-975 T972
IC971
: REC (DECK B)
EVER +5.6V +5.6V AC
3 1
REG IN
: FM

: CD Q971 RY971
RELAY
DRIVE

23 23
HCD-BX9/DX9

7-3. PRINTED WIRING BOARD – BD SECTION – • See page 21 for Circuit Boards Location.

1 2 3 4 5 6

(KSM-213DAP)

E
09

F (Page 26)

24 24
 HCD-BX9/DX9

7-4. SCHEMATIC DIAGRAM – BD SECTION – • See page 21 for Wavefoms. • See page 46 for IC Block Diagrams.

(KSM-213DAP)

(Page 29)

09

25 25
HCD-BX9/DX9
7-5. PRINTED WIRING BOARD – MAIN SECTION – • See page 21 for Circuit Boards Location.

1 2 3 4 5 6 7 8 9
(Page 38) (Page 24)
TO DRIVER BOARD

A
DX9
MODEL
JR928

DX9
FE601: DX9
MODEL
FE603: BX9

DX9 DX9 MODEL

B MODEL

(Page 34)

DX9 MODEL
BX9 MODEL

BX9 MODEL

DX9 MODEL
BX9 MODEL

BX9 MODEL

M961

BX9 MODEL
BX9
MODEL

D
TO LEAF SW BOARD

(Page 36)

E
DX9
MODEL
(Page 36)
JR917

(Page 36)
DX9 MODEL

G BX9 MODEL

DX9 MODEL

09

(Page 30, 32) (Page 30, 32)

26 26
 HCD-BX9/DX9
7-6. SCHEMATIC DIAGRAM – MAIN (1/3) SECTION – • See page 47 for IC Block Diagrams.

DX9 MODEL BX9 MODEL

DX9 BX9 BX9 MODEL

MODEL DX9

C625 BX9 MODEL

BX9
DX9

680 : BX9
330: DX9

DX9 MODEL

L642
33uH : BX9
0 : DX9

BX9 MODEL

R612
4.7k : DX9
10k : BX9

0.015 : BX9
0.01 : DX9

DX9
330 BX9

09

(Page 29)

27 27
HCD-BX9/DX9

7-7. SCHEMATIC DIAGRAM – MAIN (2/3) SECTION – • See page 21 for Wavefoms. • See page 44 for IC Pin Function Description. • See page 48 for IC Block Diagrams.

(Page 29) (Page 29)

(Page 29)

DX9 MODEL

(Page 29)
BX9
MODEL

100
100
100
BX9 MODEL

100
100
4.7k 100
100
4.7k 100
100
100
100
100

22k 470

BX9
MODEL PIN 470
FUNCTION 470

DX9 MODEL C395 0.1

DX9 MODEL

C304
0.1
2.2

DX9
MODEL

(Page 29)
2.2

C354
0.1

09

(Page 37)

28 28
 HCD-BX9/DX9
7-8. SCHEMATIC DIAGRAM – MAIN (3/3) SECTION –

(Page 27)
(Page 31, 33) (Page 31, 33)

DX9 MODEL

BX9 MODEL

BX9 MODEL

BX9 MODEL

DX9 MODEL

3.3k 4.7k

10V

C824

R901

(Page 100

25) JR908 32 D824 R830

1SS355 4.7k

JR909 33

C212
1000P

C901
DX9: 3300 25V
BX9: 3300 16V

(Page
39)

(Page 28)

25V

M5F7809L

(Page 28)
TA7807S

10V

09 (Page 28)
(Page 35)

29 29
HCD-BX9/DX9

7-9. PRINTED WIRING BOARD – POWER AMP SECTION – (BX9 MODEL) • See page 21 for Circuit Boards Location.

TO

G SUB TRANS
BOARD
(Page 40) (Page 26) (Page 40) (Page 26)

• Semiconductor
Location
Ref. No. Location
D501 B-4
D502 A-4
D503 E-4
D504 E-5
D541 B-1
D543 E-2
D551 B-4 NO504
D581 D-4 3 1
D941 A-1
D979 A-1

IC501 D-6

Q501 B-4 EP502

Q503 F-1
Q504 F-1
Q505 F-4
Q506 F-5
Q551 B-5
Q581 E-4
Q941 B-1
Q942 B-1

(Page 40)

( )

30 30
 HCD-BX9/DX9

7-10. SCHEMATIC DIAGRAM – POWER AMP SECTION – (BX9 MODEL)

RBV-602-01

-01
1.5k

15B

0.22

80V

040

0.22

80V

470

(Page 41)

C512
0.01

EP502
(Page 41)
470

1.5k
15B

0.22

040

0.22

NO504
D-GND
EVER +5.6V
STBY RELAY

(Page 41) (Page 29) (Page 29)

31 31
HCD-BX9/DX9

7-11. PRINTED WIRING BOARD – POWER AMP SECTION – (DX9 MODEL) • See page 21 for Circuit Boards Location.

(Page 42) (Page 26) (Page 26)

• Semiconductor
Location
Ref. No. Location
D501 B-4
D502 A-4
D503 E-4
D504 E-5
D541 B-1
D543 E-2
D551 B-4
D581 D-4
D941 A-1
D979 A-1

IC501 D-6

Q501 B-4
Q503 F-1
Q504 F-1
Q505 F-4
Q506 F-5
Q551 B-5
Q581 E-4
Q941 B-1
Q942 B-1

(Page 42)

NO505

G
1

(Page 42)

( )

32 32
 HCD-BX9/DX9

7-12. SCHEMATIC DIAGRAM – POWER AMP SECTION – (DX9 MODEL)

RBV-1506

NO505

VH
VH
GND (Page 43)

470

VL
VL (Page 43)

(Page 43)
470

(Page 29)
(Page 29)

33 33
HCD-BX9/DX9

7-13. PRINTED WIRING BOARD – PANEL SECTION – • See page 21 for Circuit Boards Location.

1 2 3 4 5 6 7 8

EA

D MODEL

(Page 26)

EA MODEL
EA
R732 MODEL

G DX9
MODEL
09 EA MODEL

34 34
 HCD-BX9/DX9

7-14. SCHEMATIC DIAGRAM – PANEL SECTION – • See page 21 for Wavefoms. • See page 45 for IC Pin Function Description. • See page 47 for IC Block Diagrams.

EA MODEL

PIN
FUNCTION

* R737
47k : EA
22k : EXCEPT EA
(Page 29)
DX9 MODEL
MTZJ-T-77-5.6C

0
0 0

0 0
0
* 7.0

R732
1k

ECHO
LEVEL
16V
MTZJ-T77-5.1B
D605

R747
330
0.9

2.5
4.8

2.5

2.5
2.5

2.5

C617
0.001
0.7
2.5

220 220 150 220

2.5
2.5
2.5

0.7

7.2
EA 0
MODEL 7

R746 DX9 MODEL

1k
09

35 35
HCD-BX9/DX9

7-15. PRINTED WIRING BOARD – LEAF SW SECTION – • See page 21 for Circuit Boards Location.

1 2 3 4 5 6

B
(Page 26)

C
09

(Page 26) (Page 26)

36 36
 HCD-BX9/DX9

7-16. SCHEMATIC DIAGRAM – LEAF SW SECTION –

NORMAL
SPEED

HIGH SPEED

(Page 28)

09

37 37
HCD-BX9/DX9

7-17. PRINTED WIRING BOARD – DRIVER SECTION –

1 2 3 4 5 6

09

G (Page 26)

38 38
 HCD-BX9/DX9

7-18. SCHEMATIC DIAGRAM – DRIVER SECTION –

C712
0.1

(Page 29)

09

39 39
HCD-BX9/DX9
7-19. PRINTED WIRING BOARD – TRANS SECTION – (BX9 MODEL) • See page 21 for Circuit Boards Location.

1 2 3 4 5 6 7 8 9

30

30

( )

F
(Page 30)

H 09

40 40
 HCD-BX9/DX9

7-20. SCHEMATIC DIAGRAM – TRANS SECTION – (BX9 MODEL)

(Page 31)

F973
T4A 250V

31

TRANSFORMER

31

41 41
HCD-BX9/DX9

7-21. PRINTED WIRING BOARD – TRANS SECTION – (DX9 MODEL) • See page 21 for Circuit Boards Location.

EXCEPT MX
F973

EXCEPT MX,AUS

F972

3
2
1

CN978
3

G 1

( )

42 42
 HCD-BX9/DX9

7-22. SCHEMATIC DIAGRAM – TRANS SECTION – (DX9 MODEL)

CN978
VH

G VH
GND
F973 T4A 250V

F972 T4A 250V

43 43
HCD-BX9/DX9

7-23. IC PIN FUNCTION DESCRIPTION

• MAIN BOARD IC401 M30622MAA-A25FP (MASTER CONTROL)

Pin No. Pin Name I/O Description Pin No. Pin Name I/O Description
1 SURROUND 1 O Not used. 51 N.C I Not used.
2 SURROUND 2 O Not used. 52 N.C I Not used.
3 SURROUND 3 O Not used. 53 N.C I Not used.
4 498-DATA O Data signal output for IC101 (M61504FP) 54 N.C I Not used.
5 498-CLK O Clock signal output for IC101 (M61504FP) 55 N.C I Not used.
6 N.C I Not used. 56 N.C I Not used.
7 AC-CUT I AC CUT ON (L) / OFF (H) CHECK 57 A TRIG O A deck trigger control signal output.H=ON, L-OFF
8 GND — Connected to ground. 58 B TRIG O B deck trigger control signal output.H=ON, L-OFF
9 GND — Connected to ground. 59 CAPM-H/L O Capstan motor High/Low speed control signal output.
10 XC IN I SUB CLOCK input. (32.768kHz) 60 CAPM-CONT O Capstan motor REV/FWD/STOP control signal output.H=REV, L=FWD/STOP
11 XC OUT O SUB CLOCK output. (32.768kHz) 61 N.C I Not used.
12 RESET I System reset input. 62 VCC — POWER SUPPLY (+5V)
13 X-OUT O MAIN SYSTEM CLOCK output. (16MHz) 63 N.C I Not used.
14 VSS — Vss 64 VSS — Ground.
15 X-IN I MAIN SYSTEM CLOCK input. (16MHz) 65 N.C I Not used.
16 VCC — Power supply. (+5V) 66 N.C I Not used.
17 NMI I PULL UP (EVER +5V) 67 A HALF I A deck half detect signal input.
18 WAKE_UP I WAKE UP signal input. (L) 68 A PLAY I A deck play detect signal input.
19 SCOR I CD Q-data request signal input. 69 B PLAY I B deck play detect signal input.
20 RDS-INT I RDS interrupt signal input. 70 AMS-IN I AMS signal input. L=ON,H=OFF
21 RDS-DATA I RDS data signal input. 71 TC-MUTE O Tape deck line mute ON/OFF signal output. H=ON, L=OFF
22 ST-MUTE O Tuner mute signal output. 72 R/PB/PAS I REC/PB/PASS select signal input.
23 STEREO I STEREO detect signal input. L=ON, H=OF 73 NR-ON/OFF O DOLBY NR ON/OFF signal output. H=ON, L=OFF
24 TUNED I TUNED detect signal input. L=ON, H=OFF 74 REC-MUTE O REC mute ON/OFF signal output. L=ON, H=OFF
25 ST-CE O TUNER chip eneble output. 75 BAIS O BIAS ON/OFF signal output.H=ON, L=OFF
26 ST-DOUT O TUNER data output. 76 EQ-H/N O EQ High/Normal select signal output. H=High, L=Normal
27 ST-DIN I TUNER data input. 77 PB-A/B O Playback deckA/B select signal output. H=deckB, L=deckA
28 ST-CLK O TUNER clock signal output. 78 ALC O ALC ON/OFF signal output. L=ON, H=OFF
29 IIC_CLK O IIC SCL output. 79 TC-RELAY O Tape deck relay ON/OFF signal output. H=ON, L=OFF
30 IIC_DATA O IIC SDA output. 80 N.C I Not used.
31 TXDI — Not used. 81 STBY-RELAY O STANDBY relay control signal output.
32 SQ-DATA I Subcode Q data input. (CD data) 82 PROTECT I Speaker protect signal input. L=ON, H=OFF
33 SQ-CLK I Subcode Q data input. (CD clock) 83 DBFB-ON/OFF I Not used.
34 RST1 I Not used. 84 LINE-MUTE O Line mute signal output. L=ON, H=OFF
35 CD-DATA O CD data input. 85 CD-POWER O CD-POWER ON/OFF signal output. H=ON, L=OFF
36 N.C I Not used. 86 F-SHIFT O Not used.
37 CD-CLK O CD clock input. 87 RELAY-H O Speaker terminal relay control signal output. H=ON, L=OFF
38 N.C I Not used. 88 POWER O POWER ON/OFF signal output. H=ON, L=OFF
39 CLOCK-OUT I Clock check signal input. 89 N.C O Not used.
40 SENS I BD condition signal input. 90 A SHUT O A deck reel pulse detect signal output.
41 HOLD O MODE signal input. 91 B SHUT O B deck reel pulse detect signal output.
42 XLT O CD latch signal output. 92 SOFT-TEST O Not used.
43 XRST O CD reset signal output. 93 B HALF O B deck half detect signal input.
44 LOAD-IN I Loading motor control signal input. 94 KEY/CD ADJ O KEY (for jig) / CD adjust.
45 LOAD-OUT O Loading motor control signal output. 95 MODEL-IN I MODEL input.
46 OPEN I Tray open detect signal input. 96 AVSS — Analog ground.
47 CLOSE I Tray close detect signal input. 97 SPEC-IN I Version select signal input.
48 UP/DOWN SW I Pick-up up/down detect signal input. 98 VREF — Analog Reference Voltage
49 T-SENS I CD table detect signal input. 99 AVCC — Analog Power Supply
50 TEST MODE I Not used. 100 STK-MUTE O Power amplifier mute ON/OFF signal output. H=ON, L=OFF

44 44
• PANEL BOARD IC601 TMP88CP77F-1A22 (DISPLAY CONTROL)

Pin No. Pin Name I/O Description

1 VOLUME A I VOLUME A signal input.
2 VOLUME B I VOLUME B signal input.
3 HEADPHONE I Head phone detect signal input. H=ON, L=OFF
4 N.C I Not used.
5 TUNER O TUNER LED driver output.(high active)
6 CD O CD LED driver output.(high active)
7 TAPE A/B O TAPE A/B LED driver output.(high active)
8 MD/VIDEO O MD/VIDEO LED driver output.(high active)
9-10 N.C O Not used.
11 GROOVE O GROOVE LED driver output.(high active)
12-14 N.C O Not used.
15 REC/PAUSE O REC/PAUSE LED driver output.(high active)
16 SURROUND O SURROUND LED driver output.(high active)
17-19 KEY0-2 I KEY input. (AD)
20 Super Low Freq (BPF 0) I BPF input. (AD)
21-25 BPF1-5 I BPF input. (AD)
26 ALL BAND I BPF input. (AD)
27 TIMER O TIMER SEL LED driver output.
28 STANDBY O STANDBY LED output.
29 VSS — Ground.
30 VASS — Ground.
31 AVREF — Analog reference voltage.
32 VDD — Power supply (+5V)
33-49 G17-1 O FL gride signal output.
50 P1 O FL segment signal output.
51 VDD VFT — Power supply (+5V)
52-85 P2-35 O FL segment signal output.
86 N.C I Not used.
87 VKK — –]30V driving power for FL.
88 VDD — Power supply (+5V)
89 Xin I 12.5MHz (Xin)
90 VSS — Ground.
91 Xout O 12.5MHz (Xout)
92 RESET I RESET (low active)
93-94 N.C I Not used.
95 TEST I Connected to ground.
96 WAKE UP O WAKE UP signal output for master controller. (PULL UP)
97 I2C data O IIC SDA
98 I2C clk O IIC SCL
99 N.C I Not used.
100 SIRCS I Remote commander input. (input capture)

45
7-24. IC BLOCK DIAGRAMS

IC101 CXD2587Q (BD BOARD)

AVDD3

AVDD0
AVSS3

AVSS0
DOUT

ASYO

RFDC
RFAC
CLTV

ADIO
IGEN
ASYI
BIAS
FILO
VDD

PCO
VSS

FILI

CE
TE
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41

40 SE
DIGITAL ERROR DIGITAL ASYMMETRY
INTERNAL BUS

39 FE
OUT CORRECTOR PLL CORRECTION
38 VC
16K
LRCK 61 RAM OPERATIONAL
D/A EFM AMPLIFIER
PCMD 62
INTERFACE DEMODULATOR ANALOG SWITCH
BCK 63
A/D
CONVERTER
EMPH 64
XVDD 65
CLOCK
37 XTSL
XTAI 66 TIMING GENERATOR
36 TES1
XTAO 67 LOGIC
35 TEST
XVSS 68 SERVO DSP PWM GENERATOR 34 VSS
AVDD1 69
AOUT1 FOCUS FOCUS PWM 33 FRDR
70
SERVO GENERATOR 32 FFDR
AIN1 71 SUBCODE
TRACKING TRACKING 31 TRDR
PROCESSOR
SERVO PWM GENERATOR 30 TFDR
LOUT1 72
PWM PWM SLED SLED PWM 29 SRDR
AVSS1 73 SERVO GENERATOR 28 SFDR
AVSS2 74
3rd ORDER 27 SSTP
LOUT2 75 NOISE SHAPER SERVO
DIGITAL 26 MDP
INTERFACE
CLV 25 LOCK
AIN2 76
OVER SAMPLING
AOUT2 77 DIGITAL FILTER MIRR, DFCT, 24 FOK
AVDD2 78 SERVO AUTO FOK 23 DFCT
RMUT 79 SEQUENCER DETECTOR 22 MIRR
SERIAL IN
LMUT 80 INTERFACE
21 COUT

CPU
INTERFACE

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
GFS
SCLK

XLON

SCOR
XLAT

SENS

SPOB

C2PO
XRST
SYSM

WFCK
VDD
SQSO

ATSK

XUGF
SPOA

XPCK
SQCK

CLOK
DATA

IC102 BA5974FP (BD BOARD)

CH3OUTR

CH4OUTR
CH3OUTF

CH4OUTF
POWVCC
CAPAIN3
CH4SIN'
PRFVCC

CH3RIN
CH4BIN

CH4SIN

CH3FIN

MUTE
GND

28 27 26 25 24 23 22 21 20 19 18 17 16 15

F R
R MUTE
INTERFACE

F
LEVEL SHIFT

THERMAL
SHUTDOWN
F
INTERFACE

F R F
R

INTERFACE
R
F R

1 2 3 4 5 6 7 8 9 10 11 12 13 14
VREFOUT

CH1FIN

CH1RIN

CAPAIN1

CH2FIN

CH2RIN

CAPAIN2

GND

VREFIN

POWVCC

CH2OUTR

CH2OUTF

CH1OUTR

CH1OUTF

46
IC103 CXA2568M (BD BOARD) IC602 BA3830F (PANEL BOARD)

APC PD AMP VCC 24 VCC

R02 1 REFFERENCE RESET 18 RESET
VCC 23 LC/PD CURRENT
VEE 22 LD_ON
HOLD 1
P01 2 REFFERENCE 17 f01
VEE CURRENT
AGCVTH 2 VREF
APC LD AMP
LD 3 21 HOLD_SW LINE 3 BPF DET 16 f02
VC 20 AGCCONT NF
VCC (50%/30%
OFF) BPF DET
PD 4
19 RF_BOT LINE
4 15 f03
IN
BPF DET
VC
A 5
REC 5 BPF DET 14 f04
NF
B 6 VEE
18 RFTC BPF DET
RF SUMMING AMP RF_EQ_AMP 17 RF_1 REC 6 13 f05
C 7 VC VC IN
16 RFO
BPF DET
15 RFE
D 8 RESET 7 12 f06
ERROR AMP DET
VC C
FOCUS
VEE 9 VEE
14 FE
BIAS 8 11 REC
VC C Bias LEVEL
VC
F 10
GND1 9 10 VCC
E 11

13 TE
VC
TRACKING
VC
VC BUFFER ERROR AMP
VC 12 VCC
VC
VEE
VC
IC682 BU1924 (MAIN BOARD)

VDD2
RCLK

VSS2
(NC)

XO

T1

T2
XI

16 15 14 13 12 11 10 9

CLOCK
TEST

DEFFERENTIAL BIPHASE PLL PLL 57KHz

DECODER DECODER 1187.5Hz RDS/ARI

8TH SWITCHED
CAPACITOR
FILTER

1 2 3 4 5 6 7 8
QUAL

RDATA

VREF

MUX

VDD1

VSS1

VSS3

CMP

IC701 BA6956AN (DRIVER BOARD)

TSD

CONTROL LOGIC

1 2 3 4 5 6 7 8 9
VREF

OUT2

RNF

OUT1

VM

VCC

FIN

GND

RIN

47
IC601 BA1450 (MAIN BOARD)

FM BAND WIDTH

FM/AM DET OUT

AM OSC OUT

AM MIX OUT

AM MPX IN

FM MPX IN

VCO STOP
AM RF IN

AM IF IN
AM OSC

AM AGC
V . REG

24 23 22 21 20 19 18 17 16 15 14 13

AM AM AM IF
OSC MIX

VREG SD

AM
AGC
DET 1/2

SW 1/2

PD

FM FM LED VCO
DRIVER DECODER
IF DET
SD COMP
DET

1 2 3 4 5 6 7 8 9 10 11 12
VCC
FM IN

FM SD ADJ

GND

FM DET

TUNED

STEREO

IN REQ MUTE

IF OUT

R OUT

L OUT

AM/FM
IC302 µPC1330H (MAIN BOARD) IC681 M5218AFP (MAIN BOARD)

+
+
–
–
INVERTER
V– V+
1 2 3 4 5 6 7 8

COMPARATER

1 2 3 4 5 6 7 8 9
SW R1 GND SW P1 CONT GND VCC SW P2 GND SW R2

IC651 LC72130 (MAIN BOARD)

AOUT1
AOUT2
XOUT

AMIN
FMIN
AIN2

AIN1

VDD
VSS

PD2

PD1

I02

24 23 22 21 20 19 18 17 16 15 14 13

SWALLOW COUNTER
1/16.1/17 4bits
POWER
REFERENCE ON 1/2
DIVIDER RESET

SWALLOW COUNTER
1/16.1/17 4bits
REFERENCE
DIVIDER

PHASE DETECTOR
CHARGE PUMP

2
C B DATA SHIFT REGISTER C B
I/F LATCH I/F

1 2 3 4 5 6 7 8 9 10 11 12
XIN

B05

CE

D1

CL

D0

B01

B02

B03

B04

I01

IFIN

48
 SECTION 8
EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may • Abbreviation
The components identified by mark 0 or
have some differences from the original one. AED : North European model
dotted line with mark 0 are critical for safety.
• Items marked “*” are not stocked since they AUS : Australian model Replace only with part number specified.
are seldom required for routine service. Some G : German model
delay should be anticipated when ordering these EA : Saudi Arabia model
items. MY : Malaysia model
• The mechanical parts with no reference number SP : Singapore model
in the exploded views are not supplied. MX : Mexican model
• Hardware (# mark) list and accessories and AR : Argentina model
packing materials are given in the last of this
parts list.

8-1. MAIN SECTION

#5
8 #2

6 #3

2
#3
7

4 CD mechanism deck
#3
#3

1
M961
9
3

#3

2
#3

10
#3

5
#5 1
Chassis section
Front panel section
#5

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
1 3-363-099-01 SCREW(CASE 3 TP2) 6 4-224-550-01 UPPER CASE (TOP)
2 3-363-099-41 SCREW(CASE 3 TP2) 7 1-676-191-11 SUB-TRANS BOARD(BX9)
3 4-225-038-31 SIDE PANEL L 8 4-225-041-41 BACK PANEL(BX9,MX)
4 X-4952-780-1 LOADING PANEL ASSY(BX9) 8 4-225-041-51 BACK PANEL(E,AR,SP,MY,EA,AUS)
4 X-4952-781-1 LOADING PANEL ASSY(E,AR,MX,SP,MY,AUS) 9 4-225-252-01 CUSHION (FOOT)

4 X-4952-782-1 LOADING PANEL ASSY(EA) 10 3-831-441-11 CUSHION, SARANET

5 4-225-039-31 SIDE PANEL R M961 1-763-072-11 FAN, D.C.

49
8-2. PANEL SECTION

67
* For service only 66
(Be sure to refer to "Service note" on page 4.)
* 67

58 54
67
FL601
59 61

55 65
60
S

69
67

62 59

67
68 63
60

64
Tape mechanism deck

51 71

not supplied
70

#7 56
52 57
not supplied
53

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
51 X-4952-418-1 TC HOLDER (L) ASSY(EXCEPT EA) 62 4-224-559-01 CAM(R), HEART
51 X-4952-792-1 TC HOLDER (L) ASSY(EA) 63 4-224-561-01 BRACKET (HEART CAM R)
52 X-4952-730-1 TC HOLDER (R) ASSY(EXCEPT EA) 64 4-225-053-01 SPRING R
52 X-4952-794-1 TC HOLDER (R) ASSY(EA) 65 4-224-584-11 HOLDER (FL)
53 4-225-032-11 VOL KNOB 66 A-4428-075-A PANEL BOARD, COMPLETE(BX9)

54 A-4428-077-A CD SWITCH BOARD, COMPLETE 66 A-4428-338-A PANEL BOARD, COMPLETE(EA)

55 4-962-708-81 EMBLEM (4-A), SONY 66 A-4428-342-A PANEL BOARD, COMPLETE
56 4-225-033-01 FR KNOB (E,AR,MX,SP,MY,AUS)
57 X-4952-554-1 FRONT PANEL ASSY(BX9) 67 4-951-620-01 SCREW (2.6X8), +BVTP
57 X-4952-673-1 FRONT PANEL ASSY(DX9) 68 4-224-578-11 KNOB(MIC)(DX9)
69 4-225-052-01 SPRING L
58 4-224-562-01 BRACKET (HEART CAM L)
59 4-224-803-01 SPRING (PUSH),COMPRESSION COIL 70 4-225-252-01 CUSHION (FOOT)
60 4-224-104-21 DAMPER 71 4-225-054-01 SPRING FR
61 4-224-560-01 CAM(L), HEART FL601 1-517-928-11 INDICATOR TUBE, FLUORESCENT

50
8-3. MAIN BOARD SECTION

105
#6

106 #3 108
#3
#6

AR

108 108
not supplied
107 AUS
#4 104 MX

103
108 109
E,EA,MY,SP

BX9,E,SP,MY,EA

not supplied 101

#2
102

The components identified by mark 0 or

dotted line with mark 0 are critical for safety.
Replace only with part number specified.

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
101 1-773-045-11 WIRE (FLAT TYPE) (17 CORE) 106 3-703-244-00 BUSHING (FBS001), CORD(EXCEPT E,MX)
102 A-4428-507-A MAIN BOARD, COMPLETE (BX9) 106 4-966-266-01 BUSHING (S) (FBS002), CORD(E,MX)
102 A-4428-512-A MAIN BOARD, COMPLETE (SP,MY) 107 A-4428-503-A POWER AMP BOARD, COMPLETE(BX9)
102 A-4473-080-A MAIN BOARD, COMPLETE (EA) 107 A-4428-509-A POWER AMP BOARD, COMPLETE(DX9)
102 A-4473-087-A MAIN BOARD, COMPLETE (E) 0 108 1-696-847-11 CORD, POWER(AUS)

102 A-4473-090-A MAIN BOARD, COMPLETE (AUS) 0 108 1-777-071-21 CORD, POWER(BX9)
102 A-4473-093-A MAIN BOARD, COMPLETE (AR,MX) 0 108 1-777-071-51 CORD, POWER(E,SP,MY,EA)
* 103 4-988-533-01 HOLDER, PWB 0 108 1-782-315-11 CORD, POWER(MX)
104 1-773-122-11 WIRE (FLAT TYPE) (19 CORE) 0 108 1-783-941-11 CORD, POWER(AR)
105 1-676-808-11 TRANS BOARD 0 109 1-785-504-11 ADAPTOR, CONVERSION(E,SP,MY,EA)

51
8-4. TAPE MECHANISM DECK SECTION

Note: Two different types of tape mechanism are used depending on models. 165
They maintain compatibility as an entire mechanism even though
160
there are some different parts are used. 159
164
158
161
163 157
156 167
155

159
166

158
151

162
#1

152 151 162

153
#7

152 #7
154

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
151 X-3374-156-4 PINCH LEVER (REV) ASSY 160 4-227-239-01 BELT (CAPSTAN C)
152 X-3374-155-4 PINCH LEVER (FWD) ASSY 161 X-3378-241-1 MOTOR ASSY
153 1-676-220-11 HEAD(A) BOARD 162 3-019-208-01 WASHER, STOPPER
154 1-676-221-11 HEAD(B) BOARD 163 3-016-533-01 WASHER(FR), STOPPER
155 A-2004-737-A MAIN CHASSIS ASSY 164 X-3378-041-1 FLYWHEEL (A-REV) ASSY

156 3-040-580-11 PULLEY(TENSION) 165 X-3378-040-1 FLYWHEEL (A-FWD) ASSY

157 A-2007-838-A LEAF SW BOARD, COMPLETE 166 X-3378-043-1 FLYWHEEL (B-REV) ASSY
158 3-041-947-01 BELT (FR) 167 X-3378-042-1 FLYWHEEL (B-FWD) ASSY
159 3-041-946-01 BELT (CAPSTAN B)

52
 Ver 1.1 2001.06

8-5. CD MECHANISM DECK SECTION

(CDM58-K2BD38)

201
206 208 209
213 221

207
214

212
211

219

226 208
223 205 M721
215
208
204
224
224
225 216
210
217
218
not supplied
222

203
220
220
202 227 221
227
221
201
220
BU-K2BD38
227 221

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
201 4-933-134-11 SCREW (+PTPWH M2.6X8) 215 4-221-688-01 PULLEY (B), CHUCKING
202 4-221-679-01 CAM(RELAY) 216 1-471-035-11 MAGNET ASSY
203 4-221-675-01 TABLE 217 X-4952-019-1 PULLEY (A) ASSY, CHUCKING
204 4-221-686-01 LEVER (CHANGE) 218 X-4951-889-1 HOLDER (BU) ASSY
205 4-221-676-01 TRAY 219 4-222-097-01 SCREW, STEP

206 4-933-134-51 SCREW (+PTPWH 2.6X8) 220 4-227-045-01 SPRING (INSULATOR), COIL
207 1-675-910-11 MOTOR BOARD 221 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING
208 4-951-620-01 SCREW (2.6X8), +BVTP 222 4-222-095-01 BELT
209 1-791-983-12 WIRE (FLAT TYPE) (8 CORE) 223 4-221-678-01 CAM(CONTROL)
210 1-675-911-11 SENSOR BOARD 224 4-221-683-01 GEAR (U)

211 1-675-912-11 DRIVER BOARD 225 4-221-685-01 PULLEY (S)

212 X-4952-608-1 CAM(U/D) ASSY 226 4-229-807-11 CUSHION (SLIDE)
213 4-221-681-01 LEVER (EX) 227 4-227-549-11 INSULATOR
214 4-221-682-01 LEVER (LIFTER) M721 A-4672-826-A MOTOR ASSY (INCLUDING PULLEY)

53
8-6. BASE UNIT SECTION (BU-K2BD38)

252

251

253

254

The components identified by mark 0 or

dotted line with mark 0 are critical for safety.
Replace only with part number specified.

Ref. No. Part No. Description Remarks

0 251 8-820-116-01 OPTICAL PICK-UP KSM-213DAP/Z-NP
252 1-792-024-11 WIRE (FLAT TYPE) (16 CORE)
253 A-4724-934-A BD BOARD, COMPLETE
254 4-951-620-01 SCREW (2.6X8), +BVTP

54
 SECTION 9
ELECTRICAL PARTS LIST BD
NOTE:
•Ref.Due
No. to standardization,
Part No. replacements
Description in the • COILS Remarks Ref. No. Part No. Description
When Remarks
indicating parts by reference number,
parts list may be different from the parts uH: µH please include the board name.
specified in the diagrams or the components • SEMICONDUCTORS
used on the set. In each case, u: µ, for example: The components identified by mark 0 or
• -XX, -X mean standardized parts, so they uA...: µA... , uPA... , µPA... , dotted line with mark 0 are critical for safety.
may have some difference from the original uPB... , µPB... , uPC... , µPC... , Replace only with part number specified.
one. uPD..., µPD...
• Items marked “*” are not stocked since they • Abbreviation
are seldom required for routine service. AED : North European model
Some delay should be anticipated when AUS : Australian model
ordering these items. G : German model
• CAPACITORS: EA : Saudi Arabia model
uF: µF MY : Malaysia model
• RESISTORS SP : Singapore model
All resistors are in ohms. MX : Mexican model
METAL: metal-film resistor AR : Argentina model
METAL OXIDE: Metal Oxide-film resistor
F: nonflammable

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
A-4724-934-A BD BOARD, COMPLETE C182 1-163-123-00 CERAMIC CHIP 180PF 5% 50V
*******************
< CONNECTOR >
< CAPACITOR >
CN101 1-784-741-11 CONNECTOR, FFC 19P
C101 1-163-005-11 CERAMIC CHIP 470PF 10% 50V CN102 1-793-907-11 CONNECTOR, FFC/FPC 16P
C102 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
C103 1-163-005-11 CERAMIC CHIP 470PF 10% 50V < FERRITE BEAD >
C104 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C108 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V FB101 1-500-445-21 FERRITE 0UH
FB103 1-500-445-21 FERRITE 0UH
C109 1-163-011-11 CERAMIC CHIP 0.0015uF 10% 50V
C110 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V < IC >
C111 1-163-251-11 CERAMIC CHIP 100PF 5.00% 50V
C112 1-107-682-11 CERAMIC CHIP 1uF 10.00% 16V IC101 8-752-386-85 IC CXD2587Q
C114 1-163-038-91 CERAMIC CHIP 0.1uF 25V IC102 8-759-549-28 IC BA5974FP-E2
IC103 8-752-085-51 IC CXA2568M-T6
C115 1-104-665-11 ELECT 100uF 20.00% 10V
C116 1-104-665-11 ELECT 100uF 20.00% 10V < TRANSISTOR >
C117 1-104-665-11 ELECT 100uF 20.00% 10V
C118 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V Q101 8-729-049-31 TRANSISTOR 2SB710-RTX
C119 1-163-235-11 CERAMIC CHIP 22PF 5.00% 50V
< RESISTOR >
C121 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C122 1-104-665-11 ELECT 100uF 20.00% 10V R101 1-216-077-91 RES-CHIP 15K 5% 1/10W
C123 1-163-021-91 CERAMIC CHIP 0.01uF 10.00% 50V R102 1-216-097-91 RES-CHIP 100K 5% 1/10W
C124 1-107-823-11 CERAMIC CHIP 0.47uF 10.00% 16V R103 1-216-077-91 RES-CHIP 15K 5% 1/10W
C125 1-163-038-91 CERAMIC CHIP 0.1uF 25V R104 1-216-085-00 METAL CHIP 33K 5% 1/10W
R105 1-216-073-00 METAL CHIP 10K 5% 1/10W
C126 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C127 1-104-665-11 ELECT 100uF 20.00% 10V R106 1-216-049-91 RES-CHIP 1K 5% 1/10W
C129 1-163-031-11 CERAMIC CHIP 0.01uF 50V R107 1-216-073-00 METAL CHIP 10K 5% 1/10W
C130 1-164-346-11 CERAMIC CHIP 1uF 16V R108 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
C131 1-126-964-11 ELECT 10uF 20.00% 50V R109 1-216-121-91 RES-CHIP 1M 5% 1/10W
R110 1-216-025-91 RES-CHIP 100 5% 1/10W
C133 1-164-346-11 CERAMIC CHIP 1uF 16V
C140 1-164-346-11 CERAMIC CHIP 1uF 16V R111 1-216-121-91 RES-CHIP 1M 5% 1/10W
C141 1-164-346-11 CERAMIC CHIP 1uF 16V R113 1-216-121-91 RES-CHIP 1M 5% 1/10W
C143 1-163-038-91 CERAMIC CHIP 0.1uF 25V R114 1-216-073-00 METAL CHIP 10K 5% 1/10W
C145 1-163-038-91 CERAMIC CHIP 0.1uF 25V R116 1-216-001-00 METAL CHIP 10 5% 1/10W
R117 1-216-049-91 RES-CHIP 1K 5% 1/10W
C153 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C159 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V R118 1-216-025-91 RES-CHIP 100 5% 1/10W
C162 1-104-665-11 ELECT 100uF 20.00% 10V R119 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
C163 1-104-665-11 ELECT 100uF 20.00% 10V R123 1-216-073-00 METAL CHIP 10K 5% 1/10W
C165 1-163-038-91 CERAMIC CHIP 0.1uF 25V R124 1-216-097-91 RES-CHIP 100K 5% 1/10W
R131 1-216-033-00 METAL CHIP 220 5% 1/10W
C167 1-163-237-11 CERAMIC CHIP 27PF 5.00% 50V
C168 1-163-235-11 CERAMIC CHIP 22PF 5.00% 50V R143 1-216-103-00 METAL CHIP 180K 5% 1/10W
C171 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V R144 1-216-103-00 METAL CHIP 180K 5% 1/10W
C172 1-163-123-00 CERAMIC CHIP 180PF 5% 50V R147 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
C181 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V R148 1-216-001-00 METAL CHIP 10 5% 1/10W
R149 1-216-001-00 METAL CHIP 10 5% 1/10W

55
 BD CD SWITCH DRIVER HEAD (A) HEAD (B) LEAF SW
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R158 1-216-111-00 METAL CHIP 390K 5% 1/10W 1-675-912-11 DRIVER BOARD
R159 1-216-101-00 METAL CHIP 150K 5% 1/10W *************
R162 1-216-101-00 METAL CHIP 150K 5% 1/10W
R171 1-216-078-00 RES-CHIP 16K 5% 1/10W < CAPACITOR >
R172 1-216-073-00 METAL CHIP 10K 5% 1/10W
C702 1-126-964-51 ELECT 10uF 20.00% 50V
R173 1-216-077-91 RES-CHIP 15K 5% 1/10W
R181 1-216-078-00 RES-CHIP 16K 5% 1/10W < CONNECTOR >
R182 1-216-073-00 METAL CHIP 10K 5% 1/10W
R183 1-216-077-91 RES-CHIP 15K 5% 1/10W CN701 1-785-336-11 PIN, CONNECTOR(LIGHT ANGLE)10P
CN702 1-785-550-11 CONNECTOR, FFC/FPC 8P
< CHIP NETWORK >
< DIODE >
RN101 1-233-576-11 RES, CHIP NETWORK 100
D701 8-719-109-66 DIODE MTZJ-T-77-3.3B
< SWITCH >
< IC >
S101 1-771-853-11 SWITCH, DETECTION(LIMIT IN)
IC701 8-759-598-69 IC BA6956AN
< VIBRATOR >
< RESISTOR >
X101 1-579-280-11 VIBRATOR, CRYSTAL(16.9344MHz)
************************************************************** R701 1-249-411-11 CARBON 330 5% 1/4W
R702 1-249-401-11 CARBON 47 5% 1/4W F
A-4428-077-A CD SWITCH BOARD, COMPLETE **************************************************************
**************************
1-676-220-11 HEAD (A) BOARD
< DIODE > **************

D630 8-719-056-13 DIODE SML79423C-TP15(DISC 1) < CONNECTOR >

D631 8-719-056-13 DIODE SML79423C-TP15(DISC 2)
D632 8-719-056-13 DIODE SML79423C-TP15(DISC 3) * CN1 1-564-719-11 PIN, CONNECTOR (SMALL TYPE) 3P
**************************************************************
< TRANSISTOR >
1-676-221-11 HEAD (B) BOARD
Q630 8-729-422-57 TRANSISTOR BN1A4M-TP **************
Q631 8-729-422-57 TRANSISTOR BN1A4M-TP
Q632 8-729-422-57 TRANSISTOR BN1A4M-TP < CONNECTOR >
Q633 8-729-422-57 TRANSISTOR BN1A4M-TP
Q634 8-729-422-57 TRANSISTOR BN1A4M-TP CN2 1-564-722-11 PIN, CONNECTOR (SMALL TYPE) 6P
**************************************************************
Q635 8-729-422-57 TRANSISTOR BN1A4M-TP
A-2007-838-A LEAF SW BOARD, COMPLETE
< RESISTOR > ************************

R685 1-249-417-11 CARBON 1K 5% 1/4W F < CAPACITOR >

R686 1-249-418-11 CARBON 1.2K 5% 1/4W F
R687 1-249-420-11 CARBON 1.8K 5% 1/4W F C1001 1-107-716-11 ELECT 33uF 20.00% 10V
R688 1-249-422-11 CARBON 2.7K 5% 1/4W F
R689 1-247-843-11 CARBON 3.3K 5% 1/4W < CONNECTOR >

R750 1-249-406-11 CARBON 120 5% 1/4W F CN1001 1-568-860-21 SOCKET, CONNECTOR 17P
R751 1-249-406-11 CARBON 120 5% 1/4W F
R752 1-249-406-11 CARBON 120 5% 1/4W F < DIODE >
R753 1-249-406-11 CARBON 120 5% 1/4W F
R754 1-249-406-11 CARBON 120 5% 1/4W F D1001 8-719-911-19 DIODE 1SS133T-72
D1002 8-719-911-19 DIODE 1SS133T-72
R755 1-249-406-11 CARBON 120 5% 1/4W F
< IC >
< SWITCH >
IC1001 8-749-016-76 IC RPI-321
S642 1-762-875-21 SWITCH, KEYBOARD(DISC SKIP) IC1002 8-749-016-76 IC RPI-321
S643 1-762-875-21 SWITCH, KEYBOARD(DISC 1)
S644 1-762-875-21 SWITCH, KEYBOARD(DISC 2) < TRANSISTOR >
S645 1-762-875-21 SWITCH, KEYBOARD(DISC 3)
S646 1-762-875-21 SWITCH, KEYBOARD(Z OPEN/CLOSE) Q1001 8-729-029-56 TRANSISTOR DTA144ESA-TP
**************************************************************
< RESISTOR >

R1001 1-249-409-11 CARBON 220 5% 1/4W F

R1002 1-249-409-11 CARBON 220 5% 1/4W F

56
 LEAF SW MAIN
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R1003 1-249-414-11 CARBON 560 5% 1/4W F C122 1-126-964-11 ELECT 10uF 20.00% 50V
R1004 1-247-834-11 CARBON 1.3K 5% 1/4W (DX9)
R1005 1-247-818-11 CARBON 300 5% 1/4W C123 1-126-964-11 ELECT 10uF 20.00% 50V
R1006 1-247-864-11 CARBON 24K 5% 1/4W (DX9)
R1007 1-247-780-00 CARBON 7.5 5% 1/4W C124 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C125 1-126-964-11 ELECT 10uF 20.00% 50V
R1008 1-249-417-11 CARBON 1K 5% 1/4W F (DX9)
C131 1-136-169-00 MYLAR 0.22uF 5.00% 50V
< VARIABLE RESISTOR >
C132 1-126-964-11 ELECT 10uF 20.00% 50V
RV1001 1-241-785-11 RES, ADJ, CARBON 10K C133 1-126-925-11 ELECT 470uF 20.00% 10V
RV1002 1-241-785-11 RES, ADJ, CARBON 10K C134 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C135 1-126-964-11 ELECT 10uF 20.00% 50V
< SWITCH > C140 1-163-038-91 CERAMIC CHIP 0.1uF 25V

S1001 1-570-953-11 SWITCH, PUSH (1 KEY)(DECK A PLAY) C142 1-163-038-91 CERAMIC CHIP 0.1uF 25V
S1002 1-570-953-11 SWITCH, PUSH (1 KEY)(DECK B PLAY) C144 1-126-964-11 ELECT 10uF 20.00% 50V
S1003 1-771-333-11 SWITCH, LEAF(DECK A HALF) C146 1-126-925-11 ELECT 470uF 20.00% 10V
S1004 1-771-536-11 SWITCH, LEAF(DECK A 120/70) C151 1-163-001-11 CERAMIC CHIP 220PF 10% 50V
S1005 1-771-536-11 SWITCH, LEAF(DECK A REC) C152 1-126-961-11 ELECT 2.2uF 20.00% 50V

S1006 1-771-333-11 SWITCH, LEAF(DECK B HALF) C153 1-126-964-11 ELECT 10uF 20.00% 50V
S1008 1-771-536-11 SWITCH, LEAF(DECK B 120/70) C154 1-126-964-11 ELECT 10uF 20.00% 50V
S1009 1-771-536-11 SWITCH, LEAF(DECK B REC) C155 1-126-964-11 ELECT 10uF 20.00% 50V
************************************************************** C156 1-136-161-00 MYLAR 0.047uF 5.00% 50V
C157 1-136-495-11 MYLAR 0.068uF 5.00% 50V
A-4428-507-A MAIN BOARD, COMPLETE (BX9)
********************* C158 1-136-495-11 MYLAR 0.068uF 5.00% 50V
C159 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V
A-4428-512-A MAIN BOARD, COMPLETE (SP,MY) C160 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V
********************* C161 1-163-018-00 CERAMIC CHIP 0.0056uF 5% 50V
C162 1-126-961-11 ELECT 2.2uF 20.00% 50V
A-4473-080-A MAIN BOARD, COMPLETE (EA)
********************* C165 1-136-169-00 MYLAR 0.22uF 5.00% 50V
C166 1-136-169-00 MYLAR 0.22uF 5.00% 50V
A-4473-087-A MAIN BOARD, COMPLETE (E) C167 1-126-964-11 ELECT 10uF 20.00% 50V
********************* C171 1-126-964-11 ELECT 10uF 20.00% 50V
(DX9)
A-4473-090-A MAIN BOARD, COMPLETE (AUS) C172 1-126-964-11 ELECT 10uF 20.00% 50V
********************* (DX9)

A-4473-093-A MAIN BOARD, COMPLETE (AR,MX) C175 1-126-964-11 ELECT 10uF 20.00% 50V
********************* (DX9)
C199 1-163-038-91 CERAMIC CHIP 0.1uF 25V
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S C201 1-104-665-11 ELECT 100uF 20.00% 10V
C202 1-126-925-11 ELECT 470uF 20.00% 10V
< CAPACITOR > C203 1-163-033-91 CERAMIC CHIP 0.022uF 50V

C101 1-163-001-11 CERAMIC CHIP 220PF 10% 50V C204 1-126-961-11 ELECT 2.2uF 20.00% 50V
C102 1-126-961-11 ELECT 2.2uF 20.00% 50V C205 1-163-033-91 CERAMIC CHIP 0.022uF 50V
C103 1-126-964-11 ELECT 10uF 20.00% 50V C206 1-126-961-11 ELECT 2.2uF 20.00% 50V
C104 1-126-964-11 ELECT 10uF 20.00% 50V C207 1-126-916-11 ELECT 1000uF 20.00% 6.3V
C105 1-126-964-11 ELECT 10uF 20.00% 50V C208 1-163-117-00 CERAMIC CHIP 100PF 5% 50V

C106 1-136-161-00 MYLAR 0.047uF 5.00% 50V C209 1-126-925-11 ELECT 470uF 20.00% 10V
C107 1-136-495-11 MYLAR 0.068uF 5.00% 50V C212 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C108 1-136-495-11 MYLAR 0.068uF 5.00% 50V C301 1-126-960-11 ELECT 1uF 20.00% 50V
C109 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V C302 1-130-479-00 MYLAR 0.0047uF 5% 50V
C110 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V C303 1-136-165-00 MYLAR 0.1uF 5.00% 50V

C111 1-163-018-00 CERAMIC CHIP 0.0056uF 5% 50V C304 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C112 1-126-961-11 ELECT 2.2uF 20.00% 50V C305 1-126-964-11 ELECT 10uF 20.00% 50V
C113 1-126-957-11 ELECT 0.22uF 20.00% 50V C306 1-126-960-11 ELECT 1uF 20.00% 50V
C115 1-136-169-00 MYLAR 0.22uF 5.00% 50V C307 1-126-959-11 ELECT 0.47uF 20.00% 50V
C116 1-136-169-00 MYLAR 0.22uF 5.00% 50V C308 1-126-964-11 ELECT 10uF 20.00% 50V

C117 1-126-964-11 ELECT 10uF 20.00% 50V C309 1-137-194-81 MYLAR 0.47uF 5.00% 50V
C118 1-126-961-11 ELECT 2.2uF 20.00% 50V C310 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
C121 1-126-964-11 ELECT 10uF 20.00% 50V C311 1-126-964-11 ELECT 10uF 20.00% 50V
(DX9) C312 1-126-959-11 ELECT 0.47uF 20.00% 50V
C313 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V

57
 MAIN
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
C314 1-126-964-11 ELECT 10uF 20.00% 50V C410 1-163-233-11 CERAMIC CHIP 18PF 5.00% 50V
C315 1-126-963-11 ELECT 4.7uF 20.00% 50V C411 1-163-231-11 CERAMIC CHIP 15PF 5.00% 50V
C316 1-126-933-11 ELECT 100uF 20.00% 16V C414 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C317 1-104-665-11 ELECT 100uF 20.00% 10V C416 1-126-916-11 ELECT 1000uF 20.00% 6.3V
C318 1-126-964-11 ELECT 10uF 20.00% 50V C462 1-104-665-11 ELECT 100uF 20.00% 10V

C319 1-126-961-11 ELECT 2.2uF 20.00% 50V C464 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C320 1-126-961-11 ELECT 2.2uF 20.00% 50V C497 1-126-964-11 ELECT 10uF 20.00% 50V
C321 1-163-131-00 CERAMIC CHIP 390PF 5% 50V C498 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C322 1-163-117-00 CERAMIC CHIP 100PF 5% 50V C501 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C323 1-136-157-00 MYLAR 0.022uF 5.00% 50V C502 1-136-165-00 MYLAR 0.1uF 5.00% 50V

C324 1-126-964-11 ELECT 10uF 20.00% 50V C503 1-126-964-11 ELECT 10uF 20.00% 50V
C325 1-126-965-11 ELECT 22uF 20.00% 50V C504 1-109-953-11 ELECT 2.2uF 20.00% 50V
C326 1-163-131-00 CERAMIC CHIP 390PF 5% 50V C505 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C327 1-104-665-11 ELECT 100uF 20.00% 10V C601 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C328 1-163-117-00 CERAMIC CHIP 100PF 5% 50V C602 1-163-031-11 CERAMIC CHIP 0.01uF 50V

C329 1-130-483-00 MYLAR 0.01uF 5% 50V C603 1-104-664-11 ELECT 47uF 20.00% 16V
C330 1-126-964-11 ELECT 10uF 20.00% 50V C604 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C331 1-126-965-11 ELECT 22uF 20.00% 50V C605 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C332 1-137-427-11 MYLAR 120PF 5.00% 50V C607 1-216-295-91 SHORT 0 (DX9)
C333 1-163-003-11 CERAMIC CHIP 330PF 10% 50V C611 1-104-664-11 ELECT 47uF 20.00% 16V

C334 1-163-103-00 CERAMIC CHIP 27PF 5% 50V C612 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C335 1-137-150-11 MYLAR 0.01uF 5.00% 100V C613 1-126-960-11 ELECT 1uF 20.00% 50V
C336 1-126-961-11 ELECT 2.2uF 20.00% 50V C614 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C337 1-136-155-00 FILM 0.015uF 5% 50V C615 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C338 1-130-481-00 MYLAR 0.0068uF 5% 50V C616 1-163-021-91 CERAMIC CHIP 0.01uF 10.00% 50V
(DX9)
C339 1-130-481-00 MYLAR 0.0068uF 5% 50V
C340 1-136-156-00 MYLAR 0.018uF 5.00% 50V C616 1-163-023-00 CERAMIC CHIP 0.015uF 5% 50V
C341 1-126-960-11 ELECT 1uF 20.00% 50V (BX9)
C342 1-104-664-11 ELECT 47uF 20.00% 16V C617 1-163-021-91 CERAMIC CHIP 0.01uF 10.00% 50V
C351 1-126-960-11 ELECT 1uF 20.00% 50V (DX9)
C617 1-163-023-00 CERAMIC CHIP 0.015uF 5% 50V
C352 1-130-479-00 MYLAR 0.0047uF 5% 50V (BX9)
C353 1-136-165-00 MYLAR 0.1uF 5.00% 50V C618 1-126-957-11 ELECT 0.22uF 20.00% 50V
C354 1-136-165-00 MYLAR 0.1uF 5.00% 50V C619 1-163-075-00 CERAMIC CHIP 0.047uF 50V
C355 1-126-964-11 ELECT 10uF 20.00% 50V
C356 1-126-960-11 ELECT 1uF 20.00% 50V C620 1-126-962-11 ELECT 3.3uF 20.00% 50V
C621 1-126-962-11 ELECT 3.3uF 20.00% 50V
C357 1-126-959-11 ELECT 0.47uF 20.00% 50V C622 1-104-664-11 ELECT 47uF 20.00% 16V
C358 1-126-964-11 ELECT 10uF 20.00% 50V C623 1-126-964-11 ELECT 10uF 20.00% 50V
C359 1-137-194-81 MYLAR 0.47uF 5.00% 50V C624 1-126-960-11 ELECT 1uF 20.00% 50V
C360 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
C362 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V C625 1-163-125-00 CERAMIC CHIP 220PF 5% 50V
(DX9)
C363 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V C625 1-163-137-00 CERAMIC CHIP 680PF 5% 50V
C368 1-126-964-11 ELECT 10uF 20.00% 50V (BX9)
C369 1-126-961-11 ELECT 2.2uF 20.00% 50V C626 1-104-760-11 CERAMIC CHIP 0.047uF 10.00% 50V
C370 1-126-961-11 ELECT 2.2uF 20.00% 50V C628 1-163-117-00 CERAMIC CHIP 100PF 5% 50V
C371 1-163-131-00 CERAMIC CHIP 390PF 5% 50V (DX9)
C628 1-163-133-00 CERAMIC CHIP 470PF 5% 50V
C372 1-163-117-00 CERAMIC CHIP 100PF 5% 50V (BX9)
C373 1-136-157-00 MYLAR 0.022uF 5.00% 50V
C374 1-126-964-11 ELECT 10uF 20.00% 50V C629 1-126-965-11 ELECT 22uF 20.00% 50V
C375 1-126-965-11 ELECT 22uF 20.00% 50V C630 1-126-964-11 ELECT 10uF 20.00% 50V
C376 1-163-131-00 CERAMIC CHIP 390PF 5% 50V C631 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C632 1-126-933-11 ELECT 100uF 20.00% 16V
C377 1-104-665-11 ELECT 100uF 20.00% 10V C633 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C378 1-163-117-00 CERAMIC CHIP 100PF 5% 50V
C379 1-130-483-00 MYLAR 0.01uF 5% 50V C634 1-163-016-00 CERAMIC CHIP 0.0039uF 10% 50V
C380 1-126-964-11 ELECT 10uF 20.00% 50V C635 1-163-016-00 CERAMIC CHIP 0.0039uF 10% 50V
C381 1-126-965-11 ELECT 22uF 20.00% 50V C636 1-163-021-91 CERAMIC CHIP 0.01uF 10.00% 50V
C637 1-163-021-91 CERAMIC CHIP 0.01uF 10.00% 50V
C382 1-137-427-11 MYLAR 120PF 5.00% 50V C638 1-163-135-00 CERAMIC CHIP 560PF 5% 50V
C383 1-163-003-11 CERAMIC CHIP 330PF 10% 50V (BX9)
C384 1-163-103-00 CERAMIC CHIP 27PF 5% 50V
C385 1-126-964-11 ELECT 10uF 20.00% 50V C641 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C395 1-163-038-91 CERAMIC CHIP 0.1uF 25V C644 1-163-087-00 CERAMIC CHIP 4PF 50V

58
 MAIN
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
C645 1-163-031-11 CERAMIC CHIP 0.01uF 50V C863 1-107-721-11 ELECT 4.7uF 20.00% 100V
C647 1-163-105-00 CERAMIC CHIP 33PF 5% 50V C891 1-126-964-11 ELECT 10uF 20.00% 50V
(BX9) C892 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C651 1-163-239-11 CERAMIC CHIP 33PF 5.00% 50V C901 1-126-944-11 ELECT 3300uF 20.00% 25V
C652 1-163-235-11 CERAMIC CHIP 22PF 5.00% 50V (DX9)
C653 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V C901 1-126-936-11 ELECT 3300uF 20.00% 16V
(BX9)
C655 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C656 1-163-031-11 CERAMIC CHIP 0.01uF 50V C902 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C657 1-104-664-11 ELECT 47uF 20.00% 16V C903 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C658 1-126-961-11 ELECT 2.2uF 20.00% 50V C905 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C659 1-163-031-11 CERAMIC CHIP 0.01uF 50V C906 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C907 1-128-548-11 ELECT 4700uF 20.00% 25V
C660 1-104-664-11 ELECT 47uF 20.00% 16V
C661 1-163-031-11 CERAMIC CHIP 0.01uF 50V C908 1-126-942-61 ELECT 1000uF 20.00% 25V
C662 1-126-959-11 ELECT 0.47uF 20.00% 50V C909 1-126-952-11 ELECT 1000uF 20.00% 35V
C663 1-163-031-11 CERAMIC CHIP 0.01uF 50V C911 1-126-960-11 ELECT 1uF 20.00% 50V
C669 1-163-031-11 CERAMIC CHIP 0.01uF 50V C912 1-126-916-11 ELECT 1000uF 20.00% 6.3V
C921 1-126-960-11 ELECT 1uF 20.00% 50V
C681 1-126-964-11 ELECT 10uF 20.00% 50V
(BX9) C922 1-126-933-11 ELECT 100uF 20.00% 16V
C682 1-163-135-00 CERAMIC CHIP 560PF 5% 50V C925 1-104-665-11 ELECT 100uF 20.00% 10V
(BX9) C931 1-126-964-11 ELECT 10uF 20.00% 50V
C683 1-163-038-91 CERAMIC CHIP 0.1uF 25V C932 1-126-925-11 ELECT 470uF 20.00% 10V
(BX9) C951 1-126-960-11 ELECT 1uF 20.00% 50V
C684 1-104-664-11 ELECT 47uF 20.00% 16V
(BX9) C961 1-126-960-11 ELECT 1uF 20.00% 50V
C685 1-126-964-11 ELECT 10uF 20.00% 50V C962 1-126-926-11 ELECT 1000uF 20.00% 10V
(BX9)
< FILTER >
C686 1-126-961-11 ELECT 2.2uF 20.00% 50V
(BX9) CF601 1-760-023-11 FILTER, CERAMIC (DX9)
C687 1-163-129-00 CERAMIC CHIP 330PF 5% 50V CF602 1-760-023-11 FILTER, CERAMIC (DX9)
(BX9) CF601 1-579-185-21 FILTER, CERAMIC (BX9)
C688 1-163-031-11 CERAMIC CHIP 0.01uF 50V CF602 1-579-185-21 FILTER, CERAMIC (BX9)
(BX9)
C689 1-163-135-00 CERAMIC CHIP 560PF 5% 50V < CONNECTOR >
(BX9)
C690 1-126-961-11 ELECT 2.2uF 20.00% 50V * CN201 1-569-913-11 S0CKET, CONNECTOR 19P
(BX9) CN202 1-785-336-11 PIN, CONNECTOR(LIGHT ANGLE)10P
* CN301 1-568-449-11 HOUSING, CONNECTOR(PC BOARD)3P
C691 1-163-031-11 CERAMIC CHIP 0.01uF 50V * CN304 1-569-934-11 SOCKET, CONNECTOR 17P
(BX9) CN401 1-793-766-11 CONNECTOR, BOARD TO BOARD 30P
C692 1-163-245-11 CERAMIC CHIP 56PF 5.00% 50V
(BX9) * CN891 1-564-506-11 PLUG, CONNECTOR 3P
C693 1-163-245-11 CERAMIC CHIP 56PF 5.00% 50V CN901 1-778-982-21 CONNECTOR, BOARD TO BOARD 13P
(BX9) CN902 1-778-982-21 CONNECTOR, BOARD TO BOARD 13P
C694 1-163-031-11 CERAMIC CHIP 0.01uF 50V
(BX9) < DIODE >
C695 1-163-031-11 CERAMIC CHIP 0.01uF 50V
(BX9) D501 8-719-988-61 DIODE 1SS355TE-17
D502 8-719-988-61 DIODE 1SS355TE-17
C712 1-164-159-21 CERAMIC 0.1uF 50V D503 8-719-988-61 DIODE 1SS355TE-17
C801 1-163-038-91 CERAMIC CHIP 0.1uF 25V D504 8-719-988-61 DIODE 1SS355TE-17
(BX9) D505 8-719-988-61 DIODE 1SS355TE-17
C802 1-163-038-91 CERAMIC CHIP 0.1uF 25V
(BX9) D506 8-719-988-61 DIODE 1SS355TE-17
C803 1-163-031-11 CERAMIC CHIP 0.01uF 50V D508 8-719-988-61 DIODE 1SS355TE-17
C821 1-104-665-11 ELECT 100uF 20.00% 10V D509 8-719-988-61 DIODE 1SS355TE-17
D510 8-719-988-61 DIODE 1SS355TE-17
C822 1-126-961-11 ELECT 2.2uF 20.00% 50V D511 8-719-988-61 DIODE 1SS355TE-17
C824 1-126-960-11 ELECT 1uF 20.00% 50V
C841 1-126-959-11 ELECT 0.47uF 20.00% 50V D601 8-719-056-83 DIODE UDZ-TE-17-6.8B
C851 1-163-038-91 CERAMIC CHIP 0.1uF 25V D641 8-719-914-42 DIODE DA204K-T-146
(BX9) D651 8-719-988-61 DIODE 1SS355TE-17
C852 1-163-038-91 CERAMIC CHIP 0.1uF 25V D681 8-719-988-61 DIODE 1SS355TE-17(BX9)
(BX9) D801 8-719-988-61 DIODE 1SS355TE-17

C853 1-163-031-11 CERAMIC CHIP 0.01uF 50V D822 8-719-988-61 DIODE 1SS355TE-17
C861 1-107-717-11 ELECT 47uF 20.00% 50V D824 8-719-988-61 DIODE 1SS355TE-17
C862 1-107-721-11 ELECT 4.7uF 20.00% 100V D841 8-719-988-61 DIODE 1SS355TE-17

59
 MAIN
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
D861 8-719-988-61 DIODE 1SS355TE-17 JR2 1-216-296-91 SHORT 0
D891 8-719-988-61 DIODE 1SS355TE-17 JR3 1-216-296-91 SHORT 0
D892 8-719-988-61 DIODE 1SS355TE-17 JR4 1-216-296-91 SHORT 0
D901 8-719-200-82 DIODE 11ES2-TB5 JR6 1-216-296-91 SHORT 0
D902 8-719-200-82 DIODE 11ES2-TB5 JR7 1-216-296-91 SHORT 0

D903 8-719-200-82 DIODE 11ES2-TB5 JR8 1-216-295-91 SHORT 0

D904 8-719-200-82 DIODE 11ES2-TB5 JR13 1-216-296-91 SHORT 0
D906 8-719-200-82 DIODE 11ES2-TB5 JR14 1-216-296-91 SHORT 0
D907 8-719-200-82 DIODE 11ES2-TB5 JR15 1-216-296-91 SHORT 0
D908 8-719-200-82 DIODE 11ES2-TB5 JR17 1-216-296-91 SHORT 0

D909 8-719-200-82 DIODE 11ES2-TB5 JR18 1-216-295-91 SHORT 0

D910 8-719-200-82 DIODE 11ES2-TB5 JR19 1-216-296-91 SHORT 0
D911 8-719-200-82 DIODE 11ES2-TB5 JR23 1-216-296-91 SHORT 0
D952 8-719-988-61 DIODE 1SS355TE-17 JR25 1-216-296-91 SHORT 0
D953 8-719-988-61 DIODE 1SS355TE-17 JR26 1-216-296-91 SHORT 0

< FERRITE BEAD > JR27 1-216-296-91 SHORT 0

JR29 1-216-296-91 SHORT 0
FB201 1-216-295-91 SHORT 0 JR31 1-216-295-91 SHORT 0
FB202 1-216-295-91 SHORT 0 JR32 1-216-296-91 SHORT 0
FB203 1-216-295-91 SHORT 0 JR33 1-216-296-91 SHORT 0
FB204 1-216-295-91 SHORT 0
FB416 1-216-295-91 SHORT 0 JR34 1-216-295-91 SHORT 0
JR36 1-216-295-91 SHORT 0
FB462 1-216-295-91 SHORT 0 JR37 1-216-296-91 SHORT 0
FB499 1-216-295-91 SHORT 0 JR38 1-216-296-91 SHORT 0
JR42 1-216-295-91 SHORT 0
< FRONT END >
JR44 1-216-296-91 SHORT 0
FE601 1-693-477-11 FRONT END (3 GANGS)(DX9) JR51 1-216-296-91 SHORT 0
FE603 1-693-496-11 FRONT END (4 GANG)(BX9) JR52 1-216-296-91 SHORT 0
JR54 1-216-295-91 SHORT 0
< IC > JR140 1-216-296-91 SHORT 0

IC101 8-759-652-04 IC M61504FP-TP JR601 1-216-296-91 SHORT 0

IC102 8-759-099-06 IC M5218AFP-TE1 JR602 1-216-295-91 SHORT 0
IC104 8-759-099-06 IC M5218AFP-TE1(DX9) JR603 1-216-296-91 SHORT 0
IC201 8-749-923-04 IC TOTX178A(OPTICAL DIGITAL OUT) JR604 1-216-296-91 SHORT 0
IC301 8-759-652-02 IC HA12226F JR605 1-216-296-91 SHORT 0

IC302 8-759-143-54 IC uPC1330HA JR606 1-216-296-91 SHORT 0

IC303 8-759-656-83 IC NJM4580MD-TE JR607 1-216-295-91 SHORT 0
IC304 8-759-656-83 IC NJM4580MD-TE JR608 1-216-296-91 SHORT 0
IC401 8-759-652-48 IC M30622MAA-A25FP JR609 1-216-295-91 SHORT 0 (DX9)
IC501 8-759-635-63 IC M51943BSL-TP JR611 1-216-296-91 SHORT 0

IC601 8-759-652-00 IC BA1450 JR614 1-216-295-91 SHORT 0 (BX9)

IC651 8-759-288-54 IC LC72130 JR615 1-216-295-91 SHORT 0
IC681 8-759-099-06 IC M5218AFP-TE1(BX9) JR616 1-216-295-91 SHORT 0
IC682 8-759-541-48 IC BU1924(BX9) JR619 1-216-295-91 SHORT 0
IC911 8-759-039-69 IC uPC7805AHF JR634 1-216-295-91 SHORT 0

IC921 8-759-088-08 IC uPC7812AHF JR636 1-216-295-91 SHORT 0 (BX9)

IC931 8-759-071-48 IC TA7807S JR640 1-216-295-91 SHORT 0 (DX9)
IC951 8-759-158-62 IC TA78057S JR641 1-216-295-91 SHORT 0 (BX9)
IC961 8-759-701-59 IC M5F7809L JR907 1-216-295-91 SHORT 0 (BX9)
JR910 1-216-295-91 SHORT 0 (BX9)
< IFT >
JR912 1-216-296-91 SHORT 0 (DX9)
IFT601 1-435-295-11 TRANSFORMER, IF JR923 1-216-295-91 SHORT 0 (DX9)
JR924 1-216-295-91 SHORT 0 (DX9)
< JACK > JR928 1-216-295-91 SHORT 0 (DX9)

J901 1-793-987-11 JACK, PIN 2P(MD/VIDEO) < COIL >

< JUMPER RESISTOR > L201 1-414-189-31 INDUCTOR 100uH

L301 1-410-780-11 INDUCTOR 27mH
JR1 1-216-296-91 SHORT 0 L302 1-414-193-41 INDUCTOR 220uH

60
 MAIN
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
L303 1-414-193-41 INDUCTOR 220uH R104 1-216-073-00 METAL CHIP 10K 5% 1/10W
L351 1-410-780-11 INDUCTOR 27mH R105 1-216-097-91 RES-CHIP 100K 5% 1/10W
L641 1-410-369-11 INDUCTOR CHIP 1uH(BX9) R107 1-216-105-91 RES-CHIP 220K 5% 1/10W
L642 1-216-296-91 SHORT 0 (DX9) R108 1-216-097-91 RES-CHIP 100K 5% 1/10W
L642 1-410-387-11 INDUCTOR CHIP 33uH(BX9) R109 1-216-073-00 METAL CHIP 10K 5% 1/10W

L681 1-410-393-11 INDUCTOR CHIP 100uH(BX9) R110 1-216-045-00 METAL CHIP 680 5% 1/10W
L801 1-420-872-00 COIL, AIR-CORE(BX9) R111 1-216-073-00 METAL CHIP 10K 5% 1/10W
L851 1-420-872-00 COIL, AIR-CORE(BX9) R112 1-216-089-91 RES-CHIP 47K 5% 1/10W
R113 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
< FILTER > R114 1-216-097-91 RES-CHIP 100K 5% 1/10W

LPF601 1-234-458-11 FILTER, LOW PASS R115 1-216-073-00 METAL CHIP 10K 5% 1/10W
LPF602 1-234-458-11 FILTER, LOW PASS R116 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R121 1-216-222-00 RES-CHIP 10K 5% 1/8W
< TRANSISTOR > (DX9)
R122 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q101 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6 (DX9)
Q102 8-729-144-85 TRANSISTOR 2SK1133-T1B R123 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q103 8-729-107-45 TRANSISTOR 2SC3624A-T1L15L16 (DX9)
Q141 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6
Q151 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6 R124 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
(DX9)
Q152 8-729-144-85 TRANSISTOR 2SK1133-T1B R125 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q153 8-729-107-45 TRANSISTOR 2SC3624A-T1L15L16 R132 1-216-049-91 RES-CHIP 1K 5% 1/10W
Q301 8-729-801-93 TRANSISTOR 2SD1387-34-TP R133 1-216-049-91 RES-CHIP 1K 5% 1/10W
Q302 8-729-142-46 TRANSISTOR 2SC2001TP-LK R134 1-216-049-91 RES-CHIP 1K 5% 1/10W
Q303 8-729-142-46 TRANSISTOR 2SC2001TP-LK
R141 1-216-049-91 RES-CHIP 1K 5% 1/10W
Q304 8-729-113-69 TRANSISTOR FN1F4M-T1M32 R142 1-216-051-00 METAL CHIP 1.2K 5% 1/10W
Q305 8-729-113-13 TRANSISTOR FA1A4M-T1L33 R143 1-216-089-91 RES-CHIP 47K 5% 1/10W
Q391 8-729-140-04 TRANSISTOR 2SB1116-TP-LK R144 1-216-295-91 SHORT 0
Q392 8-729-113-13 TRANSISTOR FA1A4M-T1L33 R145 1-216-041-00 METAL CHIP 470 5% 1/10W
Q393 8-729-140-04 TRANSISTOR 2SB1116-TP-LK
R146 1-216-041-00 METAL CHIP 470 5% 1/10W
Q394 8-729-113-13 TRANSISTOR FA1A4M-T1L33 R147 1-216-041-00 METAL CHIP 470 5% 1/10W
Q395 8-729-113-13 TRANSISTOR FA1A4M-T1L33 R151 1-216-049-91 RES-CHIP 1K 5% 1/10W
Q396 8-729-116-57 TRANSISTOR 2SB1068TP-K R153 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q397 8-729-113-13 TRANSISTOR FA1A4M-T1L33 R154 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q501 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6
R155 1-216-097-91 RES-CHIP 100K 5% 1/10W
Q503 8-729-113-13 TRANSISTOR FA1A4M-T1L33 R157 1-216-105-91 RES-CHIP 220K 5% 1/10W
Q504 8-729-113-69 TRANSISTOR FN1F4M-T1M32 R158 1-216-097-91 RES-CHIP 100K 5% 1/10W
Q505 8-729-113-13 TRANSISTOR FA1A4M-T1L33 R159 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q601 8-729-201-27 TRANSISTOR 2SC2715Y-TE85L R160 1-216-045-00 METAL CHIP 680 5% 1/10W
Q602 8-729-422-57 TRANSISTOR BN1A4M-TP
R161 1-216-222-00 RES-CHIP 10K 5% 1/8W
Q611 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR R162 1-216-089-91 RES-CHIP 47K 5% 1/10W
Q612 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR R163 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
Q821 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6 R164 1-216-097-91 RES-CHIP 100K 5% 1/10W
Q822 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6 R165 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q823 8-729-216-22 TRANSISTOR 2SA812-T1-M5M6
R166 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
Q824 8-729-113-13 TRANSISTOR FA1A4M-T1L33 R171 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q825 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6 (DX9)
Q828 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6 R172 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q829 8-729-120-28 TRANSISTOR 2SC1623-T1-L5L6 (DX9)
Q861 8-729-113-69 TRANSISTOR FN1F4M-T1M32 R173 1-216-073-00 METAL CHIP 10K 5% 1/10W
(DX9)
Q862 8-729-107-45 TRANSISTOR 2SC3624A-T1L15L16 R175 1-216-073-00 METAL CHIP 10K 5% 1/10W
Q863 8-729-107-45 TRANSISTOR 2SC3624A-T1L15L16
Q891 8-729-140-04 TRANSISTOR 2SB1116-TP-LK R201 1-216-025-91 RES-CHIP 100 5% 1/10W
Q892 8-729-620-05 TRANSISTOR 2SC2603TP-EF R202 1-216-085-00 METAL CHIP 33K 5% 1/10W
Q911 8-729-141-83 TRANSISTOR 2SB1375 R203 1-216-025-91 RES-CHIP 100 5% 1/10W
R204 1-216-085-00 METAL CHIP 33K 5% 1/10W
Q912 8-729-113-13 TRANSISTOR FA1A4M-T1L33 R301 1-216-085-00 METAL CHIP 33K 5% 1/10W

< RESISTOR > R302 1-216-057-00 METAL CHIP 2.2K 5% 1/10W

R303 1-216-025-91 RES-CHIP 100 5% 1/10W
R101 1-216-049-91 RES-CHIP 1K 5% 1/10W R304 1-216-025-91 RES-CHIP 100 5% 1/10W
R103 1-216-073-00 METAL CHIP 10K 5% 1/10W R305 1-216-057-00 METAL CHIP 2.2K 5% 1/10W

61
 MAIN
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R306 1-216-071-00 METAL CHIP 8.2K 5% 1/10W R384 1-216-100-00 RES-CHIP 130K 5% 1/10W
R307 1-216-065-91 RES-CHIP 4.7K 5% 1/10W R385 1-216-296-91 SHORT 0
R308 1-216-071-00 METAL CHIP 8.2K 5% 1/10W R386 1-216-099-00 METAL CHIP 120K 5% 1/10W
R309 1-216-081-00 METAL CHIP 22K 5% 1/10W R387 1-216-033-00 METAL CHIP 220 5% 1/10W
R311 1-216-121-91 RES-CHIP 1M 5% 1/10W R388 1-216-081-00 METAL CHIP 22K 5% 1/10W

R312 1-216-102-00 RES-CHIP 160K 5% 1/10W R389 1-216-075-00 METAL CHIP 12K 5% 1/10W
R313 1-216-097-91 RES-CHIP 100K 5% 1/10W R390 1-216-107-00 METAL CHIP 270K 5% 1/10W
R315 1-216-073-00 METAL CHIP 10K 5% 1/10W R391 1-216-296-91 SHORT 0
R316 1-216-234-00 RES-CHIP 33K 5% 1/8W R392 1-216-075-00 METAL CHIP 12K 5% 1/10W
R317 1-216-222-00 RES-CHIP 10K 5% 1/8W R393 1-216-081-00 METAL CHIP 22K 5% 1/10W

R318 1-216-073-00 METAL CHIP 10K 5% 1/10W R394 1-216-033-00 METAL CHIP 220 5% 1/10W
R319 1-216-111-00 METAL CHIP 390K 5% 1/10W R396 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R320 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R407 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R321 1-216-071-00 METAL CHIP 8.2K 5% 1/10W R409 1-216-295-91 SHORT 0
R331 1-216-099-00 METAL CHIP 120K 5% 1/10W R411 1-216-109-00 METAL CHIP 330K 5% 1/10W

R332 1-216-025-91 RES-CHIP 100 5% 1/10W R413 1-216-295-91 SHORT 0

R333 1-216-067-00 METAL CHIP 5.6K 5% 1/10W R417 1-216-073-00 METAL CHIP 10K 5% 1/10W
R334 1-216-100-00 RES-CHIP 130K 5% 1/10W R418 1-216-025-91 RES-CHIP 100 5% 1/10W
R335 1-216-033-00 METAL CHIP 220 5% 1/10W R419 1-216-025-91 RES-CHIP 100 5% 1/10W
R336 1-216-099-00 METAL CHIP 120K 5% 1/10W R429 1-216-025-91 RES-CHIP 100 5% 1/10W

R337 1-216-033-00 METAL CHIP 220 5% 1/10W R430 1-216-025-91 RES-CHIP 100 5% 1/10W
R338 1-216-081-00 METAL CHIP 22K 5% 1/10W R432 1-216-025-91 RES-CHIP 100 5% 1/10W
R339 1-216-075-00 METAL CHIP 12K 5% 1/10W R433 1-216-025-91 RES-CHIP 100 5% 1/10W
R340 1-216-107-00 METAL CHIP 270K 5% 1/10W R435 1-216-041-00 METAL CHIP 470 5% 1/10W
R341 1-216-033-00 METAL CHIP 220 5% 1/10W R437 1-216-041-00 METAL CHIP 470 5% 1/10W

R342 1-216-075-00 METAL CHIP 12K 5% 1/10W R440 1-216-041-00 METAL CHIP 470 5% 1/10W
0 R343 1-219-787-17 FUSIBLE 5.6 5% 1/4W R441 1-216-025-91 RES-CHIP 100 5% 1/10W
0 R344 1-219-787-17 FUSIBLE 5.6 5% 1/4W R442 1-216-025-91 RES-CHIP 100 5% 1/10W
R345 1-216-079-00 METAL CHIP 18K 5% 1/10W R443 1-216-025-91 RES-CHIP 100 5% 1/10W
R346 1-216-079-00 METAL CHIP 18K 5% 1/10W R444 1-216-025-91 RES-CHIP 100 5% 1/10W

R347 1-216-073-00 METAL CHIP 10K 5% 1/10W R445 1-216-025-91 RES-CHIP 100 5% 1/10W
R351 1-216-085-00 METAL CHIP 33K 5% 1/10W R446 1-216-025-91 RES-CHIP 100 5% 1/10W
R352 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R447 1-216-025-91 RES-CHIP 100 5% 1/10W
R353 1-216-025-91 RES-CHIP 100 5% 1/10W R448 1-216-025-91 RES-CHIP 100 5% 1/10W
R354 1-216-025-91 RES-CHIP 100 5% 1/10W R449 1-216-025-91 RES-CHIP 100 5% 1/10W

R355 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R467 1-216-025-91 RES-CHIP 100 5% 1/10W
R356 1-216-071-00 METAL CHIP 8.2K 5% 1/10W R468 1-216-025-91 RES-CHIP 100 5% 1/10W
R357 1-216-065-91 RES-CHIP 4.7K 5% 1/10W R469 1-216-025-91 RES-CHIP 100 5% 1/10W
R358 1-216-071-00 METAL CHIP 8.2K 5% 1/10W R481 1-216-025-91 RES-CHIP 100 5% 1/10W
R359 1-216-085-00 METAL CHIP 33K 5% 1/10W (BX9)
R483 1-216-073-00 METAL CHIP 10K 5% 1/10W
R360 1-216-045-00 METAL CHIP 680 5% 1/10W
R361 1-216-049-91 RES-CHIP 1K 5% 1/10W R484 1-216-073-00 METAL CHIP 10K 5% 1/10W
R363 1-216-049-91 RES-CHIP 1K 5% 1/10W R490 1-216-174-00 RES-CHIP 100 5% 1/8W
R364 1-216-045-00 METAL CHIP 680 5% 1/10W R491 1-216-174-00 RES-CHIP 100 5% 1/8W
R366 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R493 1-216-174-00 RES-CHIP 100 5% 1/8W
R494 1-216-295-91 SHORT 0
R367 1-216-089-91 RES-CHIP 47K 5% 1/10W
R368 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R495 1-216-081-00 METAL CHIP 22K 5% 1/10W
R369 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R496 1-216-089-91 RES-CHIP 47K 5% 1/10W
R371 1-216-238-91 RES-CHIP 47K 5% 1/8W R497 1-216-081-00 METAL CHIP 22K 5% 1/10W
R372 1-216-065-91 RES-CHIP 4.7K 5% 1/10W (E,AR,MX)
R497 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
R373 1-216-049-91 RES-CHIP 1K 5% 1/10W (SP,MY,AUS)
R374 1-216-089-91 RES-CHIP 47K 5% 1/10W R497 1-216-073-00 METAL CHIP 10K 5% 1/10W
R375 1-216-094-00 RES-CHIP 75K 5% 1/10W (EA)
R376 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R377 1-216-089-91 RES-CHIP 47K 5% 1/10W R497 1-216-089-91 RES-CHIP 47K 5% 1/10W
(BX9)
R378 1-216-094-00 RES-CHIP 75K 5% 1/10W R498 1-216-089-91 RES-CHIP 47K 5% 1/10W
R381 1-216-099-00 METAL CHIP 120K 5% 1/10W (DX9)
R382 1-216-025-91 RES-CHIP 100 5% 1/10W R498 1-216-085-00 METAL CHIP 33K 5% 1/10W
R383 1-216-067-00 METAL CHIP 5.6K 5% 1/10W (BX9)

The components identified by mark 0 or

dotted line with mark 0 are critical for safety.
Replace only with part number specified.
62
 MAIN
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R499 1-216-025-91 RES-CHIP 100 5% 1/10W R662 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R501 1-216-073-00 METAL CHIP 10K 5% 1/10W R663 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R502 1-216-089-91 RES-CHIP 47K 5% 1/10W R664 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R503 1-216-089-91 RES-CHIP 47K 5% 1/10W R665 1-216-025-91 RES-CHIP 100 5% 1/10W
R504 1-216-025-91 RES-CHIP 100 5% 1/10W R666 1-216-073-00 METAL CHIP 10K 5% 1/10W

R505 1-216-065-91 RES-CHIP 4.7K 5% 1/10W R667 1-216-222-00 RES-CHIP 10K 5% 1/8W
R506 1-216-041-00 METAL CHIP 470 5% 1/10W R668 1-216-049-91 RES-CHIP 1K 5% 1/10W
R508 1-216-065-91 RES-CHIP 4.7K 5% 1/10W R669 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R509 1-216-081-00 METAL CHIP 22K 5% 1/10W R681 1-216-025-91 RES-CHIP 100 5% 1/10W
R510 1-216-097-91 RES-CHIP 100K 5% 1/10W (BX9)
R682 1-216-073-00 METAL CHIP 10K 5% 1/10W
R511 1-216-174-00 RES-CHIP 100 5% 1/8W (BX9)
R523 1-216-073-00 METAL CHIP 10K 5% 1/10W
R524 1-216-073-00 METAL CHIP 10K 5% 1/10W R683 1-216-097-91 RES-CHIP 100K 5% 1/10W
R546 1-216-073-00 METAL CHIP 10K 5% 1/10W (BX9)
R547 1-216-073-00 METAL CHIP 10K 5% 1/10W R684 1-216-097-91 RES-CHIP 100K 5% 1/10W
(BX9)
R548 1-216-073-00 METAL CHIP 10K 5% 1/10W R685 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
R566 1-216-073-00 METAL CHIP 10K 5% 1/10W (BX9)
R601 1-216-295-91 SHORT 0 R686 1-216-166-00 RES-CHIP 47 5% 1/8W
R602 1-216-029-00 METAL CHIP 150 5% 1/10W (BX9)
R603 1-216-037-00 METAL CHIP 330 5% 1/10W R688 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
(DX9) (BX9)

R603 1-216-045-00 METAL CHIP 680 5% 1/10W R689 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
(BX9) (BX9)
R604 1-216-017-91 RES-CHIP 47 5% 1/10W R801 1-260-304-51 CARBON 10 5% 1/2W
R605 1-216-045-00 METAL CHIP 680 5% 1/10W (BX9)
R606 1-216-037-00 METAL CHIP 330 5% 1/10W R802 1-260-304-51 CARBON 10 5% 1/2W
R607 1-216-053-00 METAL CHIP 1.5K 5% 1/10W (BX9)
R804 1-216-089-91 RES-CHIP 47K 5% 1/10W
R608 1-216-017-91 RES-CHIP 47 5% 1/10W (DX9)
R610 1-216-045-00 METAL CHIP 680 5% 1/10W R821 1-216-238-91 RES-CHIP 47K 5% 1/8W
R611 1-216-182-00 RES-CHIP 220 5% 1/8W
R612 1-216-214-00 RES-CHIP 4.7K 5% 1/8W R822 1-216-240-00 RES-CHIP 56K 5% 1/8W
(DX9) R823 1-216-222-00 RES-CHIP 10K 5% 1/8W
R612 1-216-222-00 RES-CHIP 10K 5% 1/8W R824 1-216-073-00 METAL CHIP 10K 5% 1/10W
(BX9) R825 1-216-061-00 METAL CHIP 3.3K 5% 1/10W
R826 1-216-085-00 METAL CHIP 33K 5% 1/10W
R613 1-216-206-00 RES-CHIP 2.2K 5% 1/8W
R614 1-216-041-00 METAL CHIP 470 5% 1/10W R827 1-216-081-00 METAL CHIP 22K 5% 1/10W
(DX9) R829 1-216-230-00 RES-CHIP 22K 5% 1/8W
R614 1-216-037-00 METAL CHIP 330 5% 1/10W R830 1-216-214-00 RES-CHIP 4.7K 5% 1/8W
(BX9) R831 1-216-214-00 RES-CHIP 4.7K 5% 1/8W
R615 1-216-049-91 RES-CHIP 1K 5% 1/10W R841 1-216-081-00 METAL CHIP 22K 5% 1/10W
R616 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R842 1-216-081-00 METAL CHIP 22K 5% 1/10W
R617 1-216-041-00 METAL CHIP 470 5% 1/10W R843 1-216-214-00 RES-CHIP 4.7K 5% 1/8W
(DX9) R844 1-216-097-91 RES-CHIP 100K 5% 1/10W
R617 1-216-037-00 METAL CHIP 330 5% 1/10W R845 1-216-121-91 RES-CHIP 1M 5% 1/10W
(BX9) R851 1-260-304-51 CARBON 10 5% 1/2W
R618 1-216-049-91 RES-CHIP 1K 5% 1/10W (BX9)
R619 1-216-025-91 RES-CHIP 100 5% 1/10W
R620 1-216-065-91 RES-CHIP 4.7K 5% 1/10W R852 1-260-304-51 CARBON 10 5% 1/2W
(BX9)
R621 1-216-075-00 METAL CHIP 12K 5% 1/10W R854 1-216-089-91 RES-CHIP 47K 5% 1/10W
R622 1-216-057-00 METAL CHIP 2.2K 5% 1/10W (DX9)
R623 1-216-073-00 METAL CHIP 10K 5% 1/10W R861 1-216-049-91 RES-CHIP 1K 5% 1/10W
R624 1-216-073-00 METAL CHIP 10K 5% 1/10W R862 1-216-073-00 METAL CHIP 10K 5% 1/10W
R625 1-216-073-00 METAL CHIP 10K 5% 1/10W R863 1-216-089-91 RES-CHIP 47K 5% 1/10W

R641 1-216-097-91 RES-CHIP 100K 5% 1/10W R864 1-216-049-91 RES-CHIP 1K 5% 1/10W

R642 1-216-073-00 METAL CHIP 10K 5% 1/10W R865 1-216-049-91 RES-CHIP 1K 5% 1/10W
R655 1-216-073-00 METAL CHIP 10K 5% 1/10W R866 1-216-019-00 METAL CHIP 56 5% 1/10W
R656 1-216-222-00 RES-CHIP 10K 5% 1/8W R868 1-215-891-11 METAL OXIDE 680 5% 2W
R658 1-216-174-00 RES-CHIP 100 5% 1/8W R869 1-215-891-11 METAL OXIDE 680 5% 2W

R659 1-216-061-00 METAL CHIP 3.3K 5% 1/10W R891 1-216-222-00 RES-CHIP 10K 5% 1/8W
R660 1-216-065-91 RES-CHIP 4.7K 5% 1/10W R892 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R661 1-216-025-91 RES-CHIP 100 5% 1/10W R893 1-216-057-00 METAL CHIP 2.2K 5% 1/10W

63
 MAIN MOTOR PANEL
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R901 1-249-405-11 CARBON 100 5% 1/4W F A-4428-075-A PANEL BOARD, COMPLETE (BX9)
R911 1-216-059-00 METAL CHIP 2.7K 5% 1/10W **********************
R912 1-216-206-00 RES-CHIP 2.2K 5% 1/8W
R914 1-216-206-00 RES-CHIP 2.2K 5% 1/8W A-4428-338-A PANEL BOARD, COMPLETE (EA)
0 R916 1-219-120-51 FUSIBLE 0.15 5% 1/4W **********************

R966 1-216-019-00 METAL CHIP 56 5% 1/10W A-4428-342-A PANEL BOARD, COMPLETE

**********************
< COMPOSITION CIRCUIT BLOCK > (E,AR,MX,SP,MY,AUS)

RB641 1-234-457-11 ENCAPSULATED COMPONENT 4-224-584-11 HOLDER (FL)

< VARIABLE RESISTOR > < CAPACITOR >

RV301 1-241-764-11 RES, ADJ, CARBON 10K C601 1-124-589-11 ELECT 47uF 20% 16V
RV302 1-241-762-11 RES, ADJ, CARBON 2.2K C602 1-126-163-11 ELECT 4.7uF 20% 50V
RV303 1-241-762-11 RES, ADJ, CARBON 2.2K C603 1-162-306-11 CERAMIC 0.01uF 30.00% 16V
RV304 1-241-768-11 RES, ADJ, CARBON 220K C604 1-162-294-31 CERAMIC 0.001uF 10% 50V
RV351 1-241-764-11 RES, ADJ, CARBON 10K C605 1-162-306-11 CERAMIC 0.01uF 30.00% 16V

RV352 1-241-762-11 RES, ADJ, CARBON 2.2K C606 1-162-294-31 CERAMIC 0.001uF 10% 50V
RV353 1-241-762-11 RES, ADJ, CARBON 2.2K C607 1-104-664-11 ELECT 47uF 20.00% 10V
RV354 1-241-768-11 RES, ADJ, CARBON 220K C608 1-162-306-11 CERAMIC 0.01uF 30.00% 16V
RV611 1-241-765-11 RES, ADJ, CARBON 22K C609 1-162-306-11 CERAMIC 0.01uF 30.00% 16V
C612 1-162-303-11 CERAMIC 0.0033uF 30.00% 16V
< RELAY >
C615 1-126-963-11 ELECT 4.7uF 20.00% 50V
RY801 1-755-372-11 RELAY C616 1-162-306-11 CERAMIC 0.01uF 30.00% 16V
C617 1-162-294-31 CERAMIC 0.001uF 10% 50V
< TRANSFORMER > C620 1-126-933-11 ELECT 100uF 20.00% 16V
C621 1-104-664-11 ELECT 47uF 20.00% 16V
T301 1-423-980-11 TRANSFORMER, BIAS OSCILLATION
T601 1-435-195-11 TRANSFORMER, DISCRIMINATOR C631 1-162-294-31 CERAMIC 0.001uF 10% 50V
T602 1-234-477-11 ENCAPSULATED COMPONENT(BX9) C632 1-162-294-31 CERAMIC 0.001uF 10% 50V
C651 1-164-159-21 CERAMIC 0.1uF 50V
< TERMINAL > C652 1-126-960-11 ELECT 1uF 20.00% 50V
C653 1-126-960-11 ELECT 1uF 20.00% 50V
TM601 1-694-555-11 TERMINAL BOARD (4P)(FM/AM)(DX9)
TM601 1-694-556-21 TERMINAL BOARD (ANT.PAL)(FM/AM)(BX9) C654 1-164-159-21 CERAMIC 0.1uF 50V
TM801 1-694-635-11 TERMINAL BOARD (4P)(SPEAKER) C655 1-162-282-31 CERAMIC 100PF 10% 50V
C656 1-162-282-31 CERAMIC 100PF 10% 50V
< VIBRATOR > C657 1-162-282-31 CERAMIC 100PF 10% 50V
C658 1-162-282-31 CERAMIC 100PF 10% 50V
X401 1-567-098-41 VIBRATOR, CRYSTAL(32.768kHz)
X402 1-781-107-21 VIBRATOR, CERAMIC(16MHz) C659 1-162-282-31 CERAMIC 100PF 10% 50V
X651 1-760-549-31 VIBRATOR, CRYSTAL(4.5MHz) C660 1-162-282-31 CERAMIC 100PF 10% 50V
X681 1-579-900-21 VIBRATOR, CRYSTAL(4.332MHz)(BX9) C661 1-162-282-31 CERAMIC 100PF 10% 50V
************************************************************** C662 1-162-282-31 CERAMIC 100PF 10% 50V
C663 1-162-282-31 CERAMIC 100PF 10% 50V
1-675-910-11 MOTOR BOARD
************* C664 1-162-282-31 CERAMIC 100PF 10% 50V
C665 1-162-282-31 CERAMIC 100PF 10% 50V
< CAPACITOR > C666 1-162-282-31 CERAMIC 100PF 10% 50V
C667 1-162-282-31 CERAMIC 100PF 10% 50V
C721 1-162-306-11 CERAMIC 0.01uF 30.00% 16V C668 1-162-282-31 CERAMIC 100PF 10% 50V

< CONNECTOR > C669 1-162-282-31 CERAMIC 100PF 10% 50V

C670 1-162-282-31 CERAMIC 100PF 10% 50V
CN721 1-770-516-31 CONNECTOR, FFC 8P C671 1-162-282-31 CERAMIC 100PF 10% 50V
CN722 1-785-330-11 PIN, CONNECTOR (LIGHT ANGLE)4P C717 1-126-157-11 ELECT 10uF 20% 16V
(DX9)
< SWITCH > C718 1-126-157-11 ELECT 10uF 20% 16V
(DX9)
S701 1-771-822-11 SWITCH, LEVER (SLIDE)(OPEN/CLOSE)
************************************************************** C719 1-126-961-11 ELECT 2.2uF 20.00% 50V
(DX9)
C720 1-164-159-21 CERAMIC 0.1uF 50V(EA)
C721 1-162-294-31 CERAMIC 0.001uF 10% 50V(EA)
C722 1-162-305-11 CERAMIC 0.0068uF 30.00% 16V(EA)
C723 1-126-960-11 ELECT 1uF 20.00% 50V(EA)

The components identified by mark 0 or

dotted line with mark 0 are critical for safety.
Replace only with part number specified.
64
 PANEL
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
C724 1-136-495-11 MYLAR 0.068uF 5.00% 50V(EA) C774 1-162-282-31 CERAMIC 100PF 10% 50V
C725 1-126-959-11 ELECT 0.47uF 20.00% 50V(EA) C775 1-162-282-31 CERAMIC 100PF 10% 50V
C726 1-124-465-00 ELECT 0.47uF 20% 50V(EA) C776 1-162-282-31 CERAMIC 100PF 10% 50V
C727 1-136-167-00 MYLAR 0.15uF 5.00% 50V(EA) C777 1-162-282-31 CERAMIC 100PF 10% 50V
C728 1-162-294-31 CERAMIC 0.001uF 10% 50V(EA) C778 1-162-282-31 CERAMIC 100PF 10% 50V

C729 1-126-960-11 ELECT 1uF 20.00% 50V(EA) C779 1-162-282-31 CERAMIC 100PF 10% 50V
C730 1-161-494-00 CERAMIC 0.022uF 25V(EA) C780 1-162-282-31 CERAMIC 100PF 10% 50V
C731 1-162-305-11 CERAMIC 0.0068uF 30.00% 16V(EA) C781 1-162-282-31 CERAMIC 100PF 10% 50V
C732 1-136-495-11 MYLAR 0.068uF 5.00% 50V(EA) C782 1-162-282-31 CERAMIC 100PF 10% 50V
C733 1-104-664-11 ELECT 47uF 20.00% 10V(EA) C783 1-162-282-31 CERAMIC 100PF 10% 50V

C734 1-124-589-11 ELECT 47uF 20% 16V(EA) C784 1-162-282-31 CERAMIC 100PF 10% 50V
C735 1-124-257-00 ELECT 2.2uF 20% 50V(EA)
C736 1-126-964-11 ELECT 10uF 20.00% 50V < CONNECTOR >
(DX9)
C737 1-126-964-11 ELECT 10uF 20.00% 50V CN601 1-793-767-11 CONNECTOR, BOARD TO BOARD 30P
(DX9)
C738 1-126-961-11 ELECT 2.2uF 20.00% 50V < DIODE >
(DX9)
D601 8-719-057-30 DIODE HLMF-K205-2UL(`/1)
C739 1-162-215-31 CERAMIC 47PF 5% 50V D602 8-719-063-93 DIODE SLR325VC-N-T32(TIMER SELECT)
(DX9) D603 8-719-109-89 DIODE MTZJ-T-77-5.6C
C740 1-162-282-31 CERAMIC 100PF 10% 50V D605 8-719-109-85 DIODE MTZJ-T-77-5.1B(EA)
(DX9) D611 8-719-071-41 DIODE SELS5923C-TP15(GROOVE)
C741 1-124-463-00 ELECT 0.1uF 20% 50V
(DX9) D612 8-719-071-41 DIODE SELS5923C-TP15(CURSOL)
C742 1-162-215-31 CERAMIC 47PF 5% 50V D613 8-719-071-41 DIODE SELS5923C-TP15(CURSOL)
(DX9) D614 8-719-071-41 DIODE SELS5923C-TP15(V-GROOVE)
C743 1-162-290-31 CERAMIC 470PF 10% 50V D615 8-719-072-82 DIODE SELU5E20C-STP15(FUNCTION)
(DX9) D617 8-719-063-93 DIODE SLR325VC-N-T32(REC/PAUSE)

C744 1-162-294-31 CERAMIC 0.001uF 10% 50V D618 8-719-071-41 DIODE SELS5923C-TP15(SURROUND)
(DX9)
C745 1-126-961-11 ELECT 2.2uF 20.00% 50V < FERRITE BEAD >
(DX9)
C746 1-162-306-11 CERAMIC 0.01uF 30.00% 16V FB601 1-412-473-21 INDUCTOR 0UH
(DX9) FB602 1-412-473-21 INDUCTOR 0UH
C747 1-126-961-11 ELECT 2.2uF 20.00% 50V(EA) FB603 1-412-473-21 INDUCTOR 0UH
C748 1-162-306-11 CERAMIC 0.01uF 30.00% 16V(EA)
< FILTER >
C749 1-162-306-11 CERAMIC 0.01uF 30.00% 16V
(DX9) FL601 1-517-928-11 INDICATOR TUBE, FLUORESCENT
C750 1-162-282-31 CERAMIC 100PF 10% 50V
C751 1-162-282-31 CERAMIC 100PF 10% 50V < IC >
C752 1-162-282-31 CERAMIC 100PF 10% 50V
C753 1-162-282-31 CERAMIC 100PF 10% 50V IC601 8-759-652-49 IC TMP88CP77F-1A22
IC602 8-759-570-21 IC BA3830F-E2
C754 1-162-282-31 CERAMIC 100PF 10% 50V IC603 8-759-648-23 IC RPM6940-H4
C755 1-162-282-31 CERAMIC 100PF 10% 50V IC721 8-759-496-40 IC M65850FP(EA)
C756 1-162-282-31 CERAMIC 100PF 10% 50V IC722 8-759-634-51 IC M5218AP(DX9)
C757 1-162-282-31 CERAMIC 100PF 10% 50V
C758 1-162-282-31 CERAMIC 100PF 10% 50V < JACK >

C759 1-162-282-31 CERAMIC 100PF 10% 50V J631 1-785-569-11 JACK (SMALL TYPE)(PHONE)
C760 1-162-282-31 CERAMIC 100PF 10% 50V J721 1-785-569-11 JACK (SMALL TYPE)(MIC1)(DX9)
C761 1-162-282-31 CERAMIC 100PF 10% 50V J722 1-785-569-11 JACK (SMALL TYPE)(MIC2)(EA)
C762 1-162-282-31 CERAMIC 100PF 10% 50V
C763 1-162-282-31 CERAMIC 100PF 10% 50V < COIL >

C764 1-162-282-31 CERAMIC 100PF 10% 50V L601 1-410-509-11 INDUCTOR 10uH
C765 1-162-282-31 CERAMIC 100PF 10% 50V
C766 1-162-282-31 CERAMIC 100PF 10% 50V < TRANSISTOR >
C767 1-162-282-31 CERAMIC 100PF 10% 50V
C768 1-162-282-31 CERAMIC 100PF 10% 50V Q604 8-729-900-80 TRANSISTOR BA1A4M-TP
Q605 8-729-900-80 TRANSISTOR BA1A4M-TP
C769 1-162-282-31 CERAMIC 100PF 10% 50V Q606 8-729-900-74 TRANSISTOR BA1L3Z-TP
C770 1-162-282-31 CERAMIC 100PF 10% 50V Q607 8-729-900-74 TRANSISTOR BA1L3Z-TP
C771 1-162-282-31 CERAMIC 100PF 10% 50V Q608 8-729-900-74 TRANSISTOR BA1L3Z-TP
C772 1-162-282-31 CERAMIC 100PF 10% 50V
C773 1-162-282-31 CERAMIC 100PF 10% 50V Q609 8-729-900-74 TRANSISTOR BA1L3Z-TP

65
 PANEL
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
Q610 8-729-900-74 TRANSISTOR BA1L3Z-TP R661 1-247-843-11 CARBON 3.3K 5% 1/4W
Q611 8-729-900-74 TRANSISTOR BA1L3Z-TP R662 1-249-425-11 CARBON 4.7K 5% 1/4W F
Q612 8-729-900-74 TRANSISTOR BA1L3Z-TP R664 1-249-429-11 CARBON 10K 5% 1/4W
Q613 8-729-900-74 TRANSISTOR BA1L3Z-TP R665 1-249-410-11 CARBON 270 5% 1/4W F
Q614 8-729-900-74 TRANSISTOR BA1L3Z-TP R666 1-249-411-11 CARBON 330 5% 1/4W

Q615 8-729-111-29 TRANSISTOR 2SD1616A-TP-LK R667 1-249-413-11 CARBON 470 5% 1/4W F

Q621 8-729-900-80 TRANSISTOR BA1A4M-TP R668 1-249-414-11 CARBON 560 5% 1/4W F
Q622 8-729-900-80 TRANSISTOR BA1A4M-TP R669 1-249-414-11 CARBON 560 5% 1/4W F
Q623 8-729-900-80 TRANSISTOR BA1A4M-TP R670 1-249-415-11 CARBON 680 5% 1/4W F
Q624 8-729-900-80 TRANSISTOR BA1A4M-TP R671 1-249-422-11 CARBON 2.7K 5% 1/4W F

Q625 8-729-900-80 TRANSISTOR BA1A4M-TP R672 1-249-420-11 CARBON 1.8K 5% 1/4W F

Q626 8-729-900-80 TRANSISTOR BA1A4M-TP R673 1-249-422-11 CARBON 2.7K 5% 1/4W F
Q721 8-729-119-79 TRANSISTOR 2SC2785TP-FEK(DX9) R674 1-247-843-11 CARBON 3.3K 5% 1/4W
R675 1-249-425-11 CARBON 4.7K 5% 1/4W F
< RESISTOR > R676 1-249-427-11 CARBON 6.8K 5% 1/4W F

R603 1-249-429-11 CARBON 10K 5% 1/4W R677 1-249-429-11 CARBON 10K 5% 1/4W
R604 1-247-807-31 CARBON 100 5% 1/4W R678 1-249-432-11 CARBON 18K 5% 1/4W
R605 1-247-903-00 CARBON 1M 5% 1/4W R679 1-249-429-11 CARBON 10K 5% 1/4W
R606 1-247-807-31 CARBON 100 5% 1/4W R680 1-249-410-11 CARBON 270 5% 1/4W F
R607 1-249-429-11 CARBON 10K 5% 1/4W R681 1-249-411-11 CARBON 330 5% 1/4W

R608 1-247-807-31 CARBON 100 5% 1/4W R682 1-249-413-11 CARBON 470 5% 1/4W F
R609 1-249-429-11 CARBON 10K 5% 1/4W R683 1-249-414-11 CARBON 560 5% 1/4W F
R610 1-247-807-31 CARBON 100 5% 1/4W R684 1-249-415-11 CARBON 680 5% 1/4W F
R611 1-249-429-11 CARBON 10K 5% 1/4W R693 1-249-429-11 CARBON 10K 5% 1/4W
R612 1-249-401-11 CARBON 47 5% 1/4W F R694 1-249-429-11 CARBON 10K 5% 1/4W

R613 1-247-893-11 CARBON 390K 5% 1/4W R695 1-249-429-11 CARBON 10K 5% 1/4W
R614 1-247-893-11 CARBON 390K 5% 1/4W R696 1-249-429-11 CARBON 10K 5% 1/4W
R615 1-249-441-11 CARBON 100K 5% 1/4W R701 1-247-815-91 CARBON 220 5% 1/4W
R616 1-249-440-11 CARBON 82K 5% 1/4W R702 1-249-407-11 CARBON 150 5% 1/4W F
R617 1-249-429-11 CARBON 10K 5% 1/4W R703 1-247-815-91 CARBON 220 5% 1/4W

R618 1-249-441-11 CARBON 100K 5% 1/4W R704 1-249-411-11 CARBON 330 5% 1/4W
R619 1-249-441-11 CARBON 100K 5% 1/4W R705 1-249-410-11 CARBON 270 5% 1/4W F
R620 1-249-437-11 CARBON 47K 5% 1/4W R706 1-247-815-91 CARBON 220 5% 1/4W
R621 1-249-440-11 CARBON 82K 5% 1/4W R721 1-260-099-11 CARBON 1K 5% 1/2W
R622 1-249-429-11 CARBON 10K 5% 1/4W (DX9)
R722 1-260-100-11 CARBON 1.2K 5% 1/2W
R623 1-249-431-11 CARBON 15K 5% 1/4W (DX9)
R625 1-249-435-11 CARBON 33K 5% 1/4W
R626 1-247-895-91 CARBON 470K 5% 1/4W R723 1-247-863-91 CARBON 22K 5% 1/4W
R633 1-249-411-11 CARBON 330 5% 1/4W (EA)
R634 1-249-407-11 CARBON 150 5% 1/4W F R724 1-247-863-91 CARBON 22K 5% 1/4W
(EA)
R635 1-249-401-11 CARBON 47 5% 1/4W F R725 1-247-863-91 CARBON 22K 5% 1/4W
R636 1-249-441-11 CARBON 100K 5% 1/4W (EA)
R637 1-249-441-11 CARBON 100K 5% 1/4W R726 1-249-437-11 CARBON 47K 5% 1/4W
R638 1-249-441-11 CARBON 100K 5% 1/4W (EA)
R639 1-249-441-11 CARBON 100K 5% 1/4W R727 1-247-863-91 CARBON 22K 5% 1/4W
(EA)
R640 1-249-441-11 CARBON 100K 5% 1/4W
R641 1-249-441-11 CARBON 100K 5% 1/4W R728 1-249-429-11 CARBON 10K 5% 1/4W
R642 1-249-441-11 CARBON 100K 5% 1/4W (EA)
R643 1-249-441-11 CARBON 100K 5% 1/4W R729 1-247-863-91 CARBON 22K 5% 1/4W
R644 1-249-441-11 CARBON 100K 5% 1/4W (EA)
R730 1-247-863-91 CARBON 22K 5% 1/4W
R651 1-249-429-11 CARBON 10K 5% 1/4W (EA)
R652 1-249-410-11 CARBON 270 5% 1/4W F R731 1-247-881-00 CARBON 120K 5% 1/4W
R653 1-249-411-11 CARBON 330 5% 1/4W (EA)
R654 1-249-413-11 CARBON 470 5% 1/4W F R732 1-249-417-11 CARBON 1K 5% 1/4W F
R655 1-249-415-11 CARBON 680 5% 1/4W F (EA)

R656 1-249-417-11 CARBON 1K 5% 1/4W F R733 1-249-429-11 CARBON 10K 5% 1/4W

R657 1-249-418-11 CARBON 1.2K 5% 1/4W F (EA)
R658 1-249-418-11 CARBON 1.2K 5% 1/4W F R734 1-247-807-31 CARBON 100 5% 1/4W
R659 1-249-417-11 CARBON 1K 5% 1/4W F (DX9)
R660 1-249-420-11 CARBON 1.8K 5% 1/4W F

66
 PANEL POWER AMP
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R735 1-247-885-00 CARBON 180K 5% 1/4W S641 1-762-875-21 SWITCH, KEYBOARD(DISPLAY)
(DX9)
R736 1-249-429-11 CARBON 10K 5% 1/4W < VIBRATOR >
(DX9)
R737 1-249-437-11 CARBON 47K 5% 1/4W X601 1-579-352-11 VIBRATOR, CERAMIC(12.5MHz)
(EA) **************************************************************
R737 1-247-863-91 CARBON 22K 5% 1/4W
(EXCEPT BX9,EA) A-4428-503-A POWER AMP BOARD, COMPLETE (BX9)
R738 1-249-417-11 CARBON 1K 5% 1/4W F ***************************
(DX9)
A-4428-509-A POWER AMP BOARD, COMPLETE (DX9)
R739 1-249-441-11 CARBON 100K 5% 1/4W ***************************
(DX9)
R740 1-249-417-11 CARBON 1K 5% 1/4W F < CAPACITOR >
(DX9)
R741 1-249-429-11 CARBON 10K 5% 1/4W C501 1-126-963-11 ELECT 4.7uF 20.00% 50V
(DX9) C502 1-162-290-31 CERAMIC 470PF 10% 50V
R742 1-249-417-11 CARBON 1K 5% 1/4W F C503 1-162-286-21 CERAMIC 220PF 10.00% 50V
(EA) (DX9)
R744 1-249-441-11 CARBON 100K 5% 1/4W C504 1-104-665-11 ELECT 100uF 20.00% 10V
(DX9) C507 1-136-495-11 MYLAR 0.068uF 5.00% 50V

R745 1-247-807-31 CARBON 100 5% 1/4W C508 1-136-495-11 MYLAR 0.068uF 5.00% 50V
(DX9) C509 1-128-560-11 ELECT 22uF 20.00% 100V
R746 1-249-417-11 CARBON 1K 5% 1/4W F C510 1-128-578-11 ELECT 1uF 20.00% 100V
(DX9) C511 1-162-306-11 CERAMIC 0.01uF 30.00% 16V
R747 1-260-093-11 CARBON 330 5% 1/2W C512 1-162-306-11 CERAMIC 0.01uF 30.00% 16V
(EA) (BX9)

< VARIABLE RESISTOR > C541 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C542 1-127-752-11 ELECT 3300uF 20% 63V
RV721 1-225-739-11 RES, VAR CARBON 50K(ECHO LEVEL)(EA) C544 1-136-165-00 MYLAR 0.1uF 5.00% 50V
RV722 1-225-739-11 RES, VAR CARBON 50K(MIC LEVEL)(DX9) C545 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C546 1-127-755-11 ELECT 3300uF 20% 100V
< SWITCH > (DX9)

S601 1-418-725-11 ENCODER, ROTARY (12 TYPE)(VOLUME) C546 1-127-754-11 ELECT 3300uF 20% 80V
S611 1-762-875-21 SWITCH, KEYBOARD(f) (BX9)
S612 1-762-875-21 SWITCH, KEYBOARD(F) C551 1-126-963-11 ELECT 4.7uF 20.00% 50V
S613 1-762-875-21 SWITCH, KEYBOARD(V-GROOVE) C552 1-162-290-31 CERAMIC 470PF 10% 50V
S614 1-762-875-21 SWITCH, KEYBOARD(LOOP) C553 1-162-286-21 CERAMIC 220PF 10.00% 50V
(DX9)
S615 1-762-875-21 SWITCH, KEYBOARD(CD SYNC) C554 1-104-665-11 ELECT 100uF 20.00% 10V
S616 1-762-875-21 SWITCH, KEYBOARD(REC/PAUSE)
S617 1-762-875-21 SWITCH, KEYBOARD(ENTER/NEXT) C557 1-136-495-11 MYLAR 0.068uF 5.00% 50V
S618 1-762-875-21 SWITCH, KEYBOARD(M) C558 1-136-495-11 MYLAR 0.068uF 5.00% 50V
S619 1-762-875-21 SWITCH, KEYBOARD(AMS +) C559 1-128-560-11 ELECT 22uF 20.00% 100V
C581 1-126-967-11 ELECT 47uF 20.00% 50V
S620 1-762-875-21 SWITCH, KEYBOARD(PAUSE) C591 1-136-165-00 MYLAR 0.1uF 5.00% 50V
S621 1-762-875-21 SWITCH, KEYBOARD(– AMS)
S623 1-762-875-21 SWITCH, KEYBOARD(h) C592 1-127-752-11 ELECT 3300uF 20% 63V
S624 1-762-875-21 SWITCH, KEYBOARD(H) C596 1-127-755-11 ELECT 3300uF 20% 100V
S625 1-762-875-21 SWITCH, KEYBOARD(TAPE A/B) (DX9)
C596 1-127-754-11 ELECT 3300uF 20% 80V
S626 1-762-875-21 SWITCH, KEYBOARD(STOP) (BX9)
S627 1-762-875-21 SWITCH, KEYBOARD(CD) C942 1-126-964-11 ELECT 10uF 20.00% 50V
S628 1-762-875-21 SWITCH, KEYBOARD(TUNER/BAND) C943 1-126-968-11 ELECT 100uF 20.00% 50V
S629 1-762-875-21 SWITCH, KEYBOARD(PLAY)
S630 1-762-875-21 SWITCH, KEYBOARD(MD(VIDEO)) C980 1-164-159-21 CERAMIC 0.1uF 50V

S631 1-762-875-21 SWITCH, KEYBOARD(m) < CONNECTOR >

S632 1-762-875-21 SWITCH, KEYBOARD(SURROUND)
S633 1-762-875-21 SWITCH, KEYBOARD(DIRECTION) CN502 1-778-981-11 CONNECTOR, BOARD TO BOARD 13P
S634 1-762-875-21 SWITCH, KEYBOARD(REPEAT) CN503 1-778-981-11 CONNECTOR, BOARD TO BOARD 13P
S635 1-762-875-21 SWITCH, KEYBOARD(PLAY MODE)
< DIODE >
S636 1-762-875-21 SWITCH, KEYBOARD(EDIT)
S637 1-762-875-21 SWITCH, KEYBOARD(`/1) D501 8-719-991-33 DIODE 1SS133T-77
S638 1-762-875-21 SWITCH, KEYBOARD(GROOVE) D502 8-719-991-33 DIODE 1SS133T-77
S639 1-762-875-21 SWITCH, KEYBOARD(EQ EDIT) D503 8-719-922-03 DIODE MTZJ-T-77-18C(DX9)
S640 1-762-875-21 SWITCH, KEYBOARD(SPECTRUM) D503 8-719-110-41 DIODE MTZJ-T-77-15B(BX9)

67
 POWER AMP SENSOR SUB-TRANS
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
D504 8-719-922-03 DIODE MTZJ-T-77-18C(DX9) R522 1-249-441-11 CARBON 100K 5% 1/4W
D504 8-719-110-41 DIODE MTZJ-T-77-15B(BX9) R523 1-249-441-11 CARBON 100K 5% 1/4W
D541 8-719-302-37 DIODE RBV-602(DX9) R524 1-215-872-11 METAL OXIDE 3.3K 5% 1W
D541 8-719-302-38 DIODE RBV-602-01(BX9) (DX9)
D543 8-719-033-58 DIODE RBV-1506(DX9) R524 1-215-870-11 METAL OXIDE 1.5K 5% 1W
(BX9)
D543 8-719-302-38 DIODE RBV-602-01(BX9) R541 1-249-441-11 CARBON 100K 5% 1/4W
D551 8-719-991-33 DIODE 1SS133T-77
D581 8-719-991-33 DIODE 1SS133T-77 R542 1-249-441-11 CARBON 100K 5% 1/4W
D941 8-719-110-90 DIODE MTZJ-T-77-39D R551 1-249-417-11 CARBON 1K 5% 1/4W F
D979 8-719-110-31 DIODE MTZJ-T-77-12B R552 1-249-438-11 CARBON 56K 5% 1/4W
R553 1-249-413-11 CARBON 470 5% 1/4W F
< TERMINAL EARTH > R554 1-249-438-11 CARBON 56K 5% 1/4W

* EP501 1-537-738-21 TERMINAL, EARTH R555 1-249-417-11 CARBON 1K 5% 1/4W F

R556 1-249-431-11 CARBON 15K 5% 1/4W
< IC > R557 1-249-441-11 CARBON 100K 5% 1/4W
R558 1-219-718-11 METAL 0.1 10% 5W
IC501 8-749-017-07 IC STK412-170(DX9) (DX9)
IC501 8-749-017-05 IC STK412-040(BX9) R558 1-220-893-11 METAL 0.22 10% 5W
(BX9)
< TRANSISTOR >
R559 1-260-076-11 CARBON 10 5% 1/2W
Q501 8-729-140-84 TRANSISTOR 2SC1841TP-PAFAEA R560 1-219-718-11 METAL 0.1 10% 5W
Q503 8-729-140-82 TRANSISTOR 2SA988TP-PAFAEA (DX9)
Q504 8-729-140-84 TRANSISTOR 2SC1841TP-PAFAEA R560 1-220-893-11 METAL 0.22 10% 5W
Q505 8-729-140-84 TRANSISTOR 2SC1841TP-PAFAEA (BX9)
Q506 8-729-119-79 TRANSISTOR 2SC2785TP-FEK 0 R561 1-212-881-11 FUSIBLE 100 5% 1/4W
R581 1-249-435-11 CARBON 33K 5% 1/4W
Q551 8-729-140-84 TRANSISTOR 2SC1841TP-PAFAEA
Q581 8-729-140-84 TRANSISTOR 2SC1841TP-PAFAEA R582 1-249-435-11 CARBON 33K 5% 1/4W
Q941 8-729-048-52 TRANSISTOR 2SA1932(TP) R591 1-249-441-11 CARBON 100K 5% 1/4W
Q942 8-729-119-76 TRANSISTOR 2SA1175TP-HFE R592 1-249-441-11 CARBON 100K 5% 1/4W
R941 1-216-478-11 METAL OXIDE 390 5% 3W
< RESISTOR > R942 1-249-429-11 CARBON 10K 5% 1/4W

R501 1-249-417-11 CARBON 1K 5% 1/4W F R943 1-249-417-11 CARBON 1K 5% 1/4W F

R502 1-249-438-11 CARBON 56K 5% 1/4W R944 1-249-397-11 CARBON 22 5% 1/4W F
R503 1-249-413-11 CARBON 470 5% 1/4W F R980 1-249-429-11 CARBON 10K 5% 1/4W
R504 1-249-438-11 CARBON 56K 5% 1/4W
R505 1-249-417-11 CARBON 1K 5% 1/4W F < THERMISTOR >

R506 1-249-431-11 CARBON 15K 5% 1/4W TH501 1-807-796-11 THERMISTOR

R507 1-249-441-11 CARBON 100K 5% 1/4W **************************************************************
R508 1-219-718-11 METAL 0.1 10% 5W
(DX9) 1-675-911-11 SENSOR BOARD
R508 1-220-893-11 METAL 0.22 10% 5W **************
(BX9)
R509 1-260-076-11 CARBON 10 5% 1/2W < IC >

R510 1-219-718-11 METAL 0.1 10% 5W IC711 8-749-016-76 IC RPI-321

(DX9)
R510 1-220-893-11 METAL 0.22 10% 5W < RESISTOR >
(BX9)
0 R511 1-212-881-11 FUSIBLE 100 5% 1/4W R711 1-247-876-11 CARBON 75K 5% 1/4W
0 R512 1-202-972-61 FUSIBLE 1 5% 1/4W R712 1-247-815-91 CARBON 220 5% 1/4W
R513 1-249-435-11 CARBON 33K 5% 1/4W R713 1-249-429-11 CARBON 10K 5% 1/4W

R514 1-249-421-11 CARBON 2.2K 5% 1/4W F < SWITCH >

R515 1-247-863-91 CARBON 22K 5% 1/4W
R516 1-249-429-11 CARBON 10K 5% 1/4W S711 1-771-821-11 SWITCH, PUSH (1 KEY)(UP/DOWN)
R517 1-249-421-11 CARBON 2.2K 5% 1/4W F **************************************************************
R518 1-249-435-11 CARBON 33K 5% 1/4W
1-676-191-11 SUB-TRANS BOARD (BX9)
R519 1-249-439-11 CARBON 68K 5% 1/4W ****************
R520 1-215-872-11 METAL OXIDE 3.3K 5% 1W
(DX9) < CAPACITOR >
R520 1-215-870-11 METAL OXIDE 1.5K 5% 1W
(BX9) C973 1-126-933-11 ELECT 100uF 20.00% 16V
R521 1-249-441-11 CARBON 100K 5% 1/4W (BX9)

The components identified by mark 0 or

dotted line with mark 0 are critical for safety.
Replace only with part number specified.
68
 SUB-TRANS TRANS
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
C975 1-126-768-11 ELECT 2200uF 20.00% 16V < RESISTOR >
(BX9)
C976 1-164-159-21 CERAMIC 0.1uF 50V 0 R951 1-219-120-11 FUSIBLE 0.15 5% 1/4W
(BX9) 0 R952 1-219-120-11 FUSIBLE 0.15 5% 1/4W
C977 1-164-159-21 CERAMIC 0.1uF 50V 0 R953 1-219-120-11 FUSIBLE 0.15 5% 1/4W
(BX9)
C978 1-164-159-21 CERAMIC 0.1uF 50V < SWITCH >
(BX9)
0 S951 1-771-291-11 SWITCH, POWER(VOLTAGE SELECTOR)
< CONNECTOR > (E,AR,SP,MY,EA)

CN974 1-564-321-00 PIN, CONNECTOR 2P(BX9) < TRANSFORMER >

CN976 1-506-468-11 PIN, CONNECTOR 3P(BX9)
0 T971 1-435-323-11 POWER TRANSFORMER(DX9)
< DIODE > 0 T971 1-435-324-11 POWER TRANSFORMER(BX9)
**************************************************************
D971 8-719-991-33 DIODE 1SS133T-77(BX9)
D972 8-719-200-82 DIODE 11ES2-NTA1B(BX9) MISCELLANEOUS
D973 8-719-200-82 DIODE 11ES2-NTA1B(BX9) ***************
D974 8-719-200-82 DIODE 11ES2-NTA1B(BX9)
D975 8-719-200-82 DIODE 11ES2-NTA1B(BX9) 101 1-773-045-11 WIRE (FLAT TYPE) (17 CORE)
104 1-773-122-11 WIRE (FLAT TYPE) (19 CORE)
D976 8-719-991-33 DIODE 1SS133T-77(BX9) 0 108 1-696-847-11 CORD, POWER(AUS)
0 108 1-777-071-21 CORD, POWER(BX9)
< IC > 0 108 1-777-071-51 CORD, POWER(E,SP,MY,EA)

IC971 8-759-039-69 IC uPC7805AHF(BX9) 0 108 1-782-315-11 CORD, POWER(MX)

0 108 1-783-941-11 CORD, POWER(AR)
< TRANSISTOR > 0 109 1-785-504-11 ADAPTOR, CONVERSION(E,SP,MY,EA)
209 1-791-983-12 WIRE (FLAT TYPE) (8 CORE)
Q971 8-729-119-78 TRANSISTOR 2SC2785TP-HFE(BX9) 216 1-471-035-11 MAGNET ASSY

< RESISTOR > 0 251 8-820-116-01 OPTICAL PICK-UP KSM-213DAP/Z-NP

252 1-792-024-11 WIRE (FLAT TYPE) (16 CORE)
R974 1-249-441-11 CARBON 100K 5% 1/4W FL601 1-517-928-11 INDICATOR TUBE, FLUORESCENT
(BX9) M721 A-4672-826-A MOTOR ASSY
R975 1-249-429-11 CARBON 10K 5% 1/4W M961 1-763-072-11 FAN, D.C.
(BX9) **************************************************************

< RELAY > **************

HARDWARE LIST
0 RY971 1-755-276-11 RELAY, POWER(BX9) **************

< TRANSFORMER > #1 7-628-254-05 SCREW +PS 2.6X5

#2 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
0 T972 1-435-210-11 TRANSFORMER, POWER(BX9) #3 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
************************************************************** #4 7-685-650-79 SCREW +BVTP 3X16 TYPE2 N-S
#5 7-685-648-79 SCREW +BVTP 3X12 TYPE2 N-S
1-676-808-11 TRANS BOARD
************* #6 7-685-881-09 SCREW +BVTT 4X8 (S)
#7 7-685-781-09 SCREW +PTT 2X4 (2)
1-533-293-31 FUSE HOLDER

< CONNECTOR >

CN975 1-564-321-00 PIN, CONNECTOR 2P(DX9)

* CN977 1-564-524-11 PLUG, CONNECTOR 9P(DX9)
* CN977 1-564-528-11 PLUG, CONNECTOR 13P(BX9)
* CN978 1-564-214-11 PIN, CONNECTOR (B3PS-VH) 3P(DX9)

< FUSE >

0 F971 1-532-506-31 FUSE T6.3AL/250V(EXCEPT BX9,AUS)

0 F972 1-532-504-31 FUSE T4A/250V(EXCEPT BX9,AUS,MX)
0 F973 1-532-504-31 FUSE T4A/250V(EXCEPT MX)
0 F974 1-532-506-31 FUSE T6.3AL/250V
0 F975 1-532-506-31 FUSE T6.3AL/250V

The components identified by mark 0 or

dotted line with mark 0 are critical for safety.
Replace only with part number specified.

69
HCD-BX9/DX9

REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.

Ver. Date Description of Revision

1.1 2001.06 Correction of exploded views (227). (SPM-01021)

1.0 2000.04 New.