Scribd
Upload
181 views3 pages

08 TIA-Portal Practical

This document contains 3 sets (A, B, C) of practical questions for an NSQF level-6 final test in TIA. Each set contains a ladder logic programming question and asks the student to write a program, distribute marks for programming, hardware and simulation, and provides a total of 60 marks. Set A asks to program a lamp that glows for 15 seconds when a start switch is on and turns off when the start or reset switch is switched. Set B asks to program different lamps to turn on based on different sensor inputs and turn off all lamps using a memory bit. Set C asks to develop logic to sequentially control two motors that can be individually started and stopped, and turn off together using different stop switches

Uploaded by

Ankit
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
181 views3 pages

08 TIA-Portal Practical

This document contains 3 sets (A, B, C) of practical questions for an NSQF level-6 final test in TIA. Each set contains a ladder logic programming question and asks the student to write a program, distribute marks for programming, hardware and simulation, and provides a total of 60 marks. Set A asks to program a lamp that glows for 15 seconds when a start switch is on and turns off when the start or reset switch is switched. Set B asks to program different lamps to turn on based on different sensor inputs and turn off all lamps using a memory bit. Set C asks to develop logic to sequentially control two motors that can be individually started and stopped, and turn off together using different stop switches

Uploaded by

Ankit
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 3

CENTRAL TOOL ROOM LUDHIANA

NSQF (LEVEL-6) Final Test

Course: ADMMA (____Batch) Max Marks:


Subject: TIA Time : 1 hr.
Name: Roll No :

(Set A)
Practical Question

1. Write a program in ladder logic that a Lamp should glow when start switch S1 is made ON. Lamp should
go off after 15 second automatically. Lamp should go OFF immediately when start switch S1 is made OFF.
Lamp should go OFF immediately also when reset switch S2 is made ON even before the expiry of 15 sec
time.

MARKS DISTRIBUTION
PROGRAMMIMG HARDWARE SIMULATION TOTAL
20 20 20 60
CENTRAL TOOL ROOM LUDHIANA
NSQF (LEVEL-6) Final Test

Course: ADMMA (___Batch) Max Marks:


Subject: TIA Time : 1 hr.
Name: Roll No :

(Set B)
Practical Question

1. Write a program in ladder logic, When the sensor S1 is made ON the lamp B1 should glow When the
sensor S2 is made ON the lamp B2 should glow When the sensor S3 is made ON the lamp B3 should glow
When the sensor S4 is made ON the entire lamp should OFF. Hints: - Do it by use of a memory bit

MARKS DISTRIBUTION
PROGRAMMIMG HARDWARE SIMULATION TOTAL
20 20 20 60
CENTRAL TOOL ROOM LUDHIANA
NSQF (LEVEL-6) Final Test

Course: ADMMA (___Batch) Max Marks:


Subject: TIA Time : 1 hr.
Name: Roll No :

(Set C)
Practical Question

1. Develop LAD logic for sequential control of two motors. Two motors (M1, M2) are to be
separately started and stop from individual start stop push button stations. Motor M2 can only
be started when Motor M1 starts. Once motor M2 starts it can be separately stopped but if the
stop push button for motor M1 is pressed then both the motor M1& M2 gets OFF. While running
Motor M1 & M2 both if a common stop switch is pressed it makes both the motor OFF.

MARKS DISTRIBUTION
PROGRAMMIMG HARDWARE SIMULATION TOTAL
20 20 20 60

You might also like