Scribd
Upload
42 views11 pages

LPW 2022-23

1. The document provides instructions for students for their Machine Design practice laboratory work. It lists 11 points covering requirements like bringing necessary books and materials, recording design work, drawing neat designs, including title blocks and bills of materials in set formats, clearly dimensioning mating parts, planning work in advance, and incorporating teacher feedback. 2. The document then provides 4 problems covering designs of single and multi-plate clutches, centrifugal clutches, hydraulic presses, and internal expanding brakes. It gives specifications for each design exercise and states any additional data needed may be assumed. Students are to complete the designs and drawings. 3. The instructions aim to guide students in properly planning and executing their machine design laboratory work

Uploaded by

Albatross Beastboy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
42 views11 pages

LPW 2022-23

1. The document provides instructions for students for their Machine Design practice laboratory work. It lists 11 points covering requirements like bringing necessary books and materials, recording design work, drawing neat designs, including title blocks and bills of materials in set formats, clearly dimensioning mating parts, planning work in advance, and incorporating teacher feedback. 2. The document then provides 4 problems covering designs of single and multi-plate clutches, centrifugal clutches, hydraulic presses, and internal expanding brakes. It gives specifications for each design exercise and states any additional data needed may be assumed. Students are to complete the designs and drawings. 3. The instructions aim to guide students in properly planning and executing their machine design laboratory work

Uploaded by

Albatross Beastboy
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 11

NIRMA UNIVERSITY

INSTITUTE OF TECHNOLOGY
Mechanical engineering Department

Machine Design I (2ME501) (LPW)

Instructions to students for Machine Design Practice:

1. All the students should come with a book on machine design, data book, calculator, notebook
etc.
2. The design work carried out for a particular major problem should be recorded during each
practical turn and the concerned teacher's check/signature is to be obtained.
3. The drawing work should be neat and clean.
4. The title block should be drawn as per IS Code of drawing. (SP 46)
5. The bill of material should
• Contain the name of the exercise done (i.e. e.g. Design of steam stop value etc.)
• Have the specifications of standard items (such as screw, bolts, bearings, seals, washers,
etc.) as per IS.
• Have the indication of materials used for components as per IS (i.e. e.g. C 40 or 50)
6. The dimensions of mating parts for assembly must be clearly mentioned (with tolerance
if applicable) and checked.
7. Planning for the term should be done in advance.
8. Teacher will give schedule for the work to be done during semester and student will plan their
activity so as to meet the schedule.
9. Report writing should contain data of a problem, diagram of the design to be carried out with
notations assumptions made, references used, sketc hes of components designed as the
design progresses and at the end.
10. Student should make all corrections given by the teacher and submit the drawing sheet in bound
from as desired.
11. Due weightage will be given to the students for their understanding, diligence, quality of work
and regularity in laboratory work.

H.O.D. (MECH)
Prob.:- 1 Single plate clutch: Batch A1/B1

Ex.1 Batch A11/B11

An industrial diesel engine develops 15 kW at 4000 rpm. Design and draw the clutch.
Use any additional data if required for the design.

Ex.2 Batch A12/B12


An industrial diesel engine develops 1.8 kW at 300 rpm. Design and draw the single plate
clutch as shown above. Use any additional data if required for the design.

Ex.3 Batch A13/B13


Design a multi-plate plate clutch for multi-cylinder engine which has maximum torsional
movement of 4 kW at 750 rpm. Use any additional data if required for the design.

Ex.4 Batch A14/B14

Design a multi-plate plate clutch for multi-cylinder engine which has maximum torsional
movement of 18 kW at 1900 rpm as shown above. Use any additional data if required for
the design.
Prob.:- 2 Centrifugal clutch: Batch A2/B2

Ex:1 Design and draw centrifugal clutch as shown in figure from the following data

Description Batch A21/B21


Power transmission 2 kw
Operating Speed 1500
No. of shoes 2
Engagement speed 750 rpm

Any other data necessary for the design may be assumed

Ex:2 Design and draw centrifugal clutch as shown in figure from the following data
Description Batch A22/B22
Power transmission 3.2 kw
Operating Speed 2500 rpm
No. of shoes 2
Engagement speed 1250 rpm

Any other data necessary for the design may be assumed


Ex:3 Design and draw centrifugal clutch as shown in figure from the following data

Description Batch A23/B23


Power transmission 3 kw
Operating Speed 2600 rpm
No. of shoes 3
Engagement speed 2000 rpm

Any other data necessary for the design may be assumed


Ex:4 Design and draw centrifugal clutch as shown in figure from the following data

Description Batch A24/B24


Power transmission 12 kw
Operating Speed 1200 rpm
No. of shoes 4
Engagement speed 900 rpm

Any other data necessary for the design may be assumed.

Ex:5 Design and draw centrifugal clutch as shown in figure from the following data

Description Batch A25/B25


Power transmission 10 kw
Operating Speed 1000 rpm
No. of shoes 4
Engagement speed 750 rpm

Any other data necessary for the design may be assumed.


Prob.:- 3 Hydraulic Press: A3/B3

Ex.1 Design and draw hydraulic press for cotton bailing from the following data:

Description Batch A31/B31


capacity 5 Ton.
Working space 500 x 500 x 500(H)
Pressure 120 bar
Minimum 125 mm
baling height

Any other data necessary for the design may be assumed.


Ex.2 Design and draw single hydraulic cylinder scissor lift trolley from the following
data:

Description Batch A32/B32


capacity 500 kg
Working space 900mm x 500mm
Elevation 500mm

Any other data necessary for the design may be assumed.


Ex.3 Design and draw single hydraulic cylinder tail stock for drilling hole from the
following data:

Description Batch A33/B33


capacity 25mm drill hole in MS rod

Any other data necessary for the design may be assumed.

Ex.4 Design and draw hydraulic press for use of pipe bending from the following data:

Description Batch A34/B34


capacity To bend pipe of 1.5 inch
Any other data necessary for the design may be assumed.

Prob.:- 4 Internal Expanding Brake: A4/B4

Design and Draw an internal expanding double shoe brake/ externally closing brake for
the following configuration and data.

Description Batch Batch 2 Batch 3 Batch 3


A41/B41 A42/B42 A43/B43 A44/B44

Actuating force (N) 4500 700 500 7200


Torque transmitting capacity (N.m) 3000 60 150 2400

Any other data necessary for the design may be assumed.


1. Batch A41/B41

2. Batch A42/B42
3. Batch A43/B43

4. Batch A44/B44

You might also like